Assembly Instructions

CAP
CANDLE
COVER
SOCKET
CRYSTAL
DECORATION
ARM
HANGER
LOCK SCREW
HEX
COUPLING
CENTER
COLUMN
SUPPORT
ARM
JUNCTION BOX
SCROLLED PART
SMALL TUBE
FINIAL
CRYSTAL
SPACER
TUBE
OUTLET BOX
HOUSE SUPPLY and
GROUND WIRES
OUTLET BOX SCREWS
not supplied()
CROSSBAR
LOCK WASHER A
LOCK NUT A
NIPPLE
LOCK NUT B
LOCK WASHER B
CANOPY CHAIN LOOP
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE CHAIN
CEILING CANOPY
CANOPY LOCK RING
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE LOOP
NIPPLE
,.
..
1 Before beginning the installation carefully unpack
and identify all parts referring to the illustration
2 Turn power to the installation point OFF at circuit
breaker
3 Unfold the SUPPORT ARMS to the proper locations
Position the SPACER TUBE over the HEX
COUPLING on the top end of the JUNCTION BOX
assembly and then thread the nipple on the end of
the CENTER COLUMN onto the HEX COUPLING
Hand tighten until snug Please make sure the
mounting holes on the side of the CENTER
COLUMN line up the mounting holes on the side of
the JUNCTION BOX assembly
4 Locate the DECORATIVE ARMS Match the holes
on them with the mounting holes on the side of the
CENTER COLUMN and JUNCTION BOX assembly
Secure them by threading the LOCK SCREWS into
the mounting holes Hand tighten until snug
6 Fasten the CROSSBAR to the OUTLET BOX with
(2)OUTLET BOX SCREWS(not supplied). Proceed
to thread LOCK NUT A and LOCK WASHER A onto
the top end of NIPPLE. Thread NIPPLE into the
center of CROSSBAR. Locate the LOCK NUT B onto
the bottom end of the NIPPLE. Tighten LOCK NUT A
against CROSSBAR with plier until snug.
7. Locate the FIXTURE CHAIN and determine desired
hanging height of fixture.Adjust chain by removing
links if needed. Please note that depending on chain
material thickness, you might be required to use
chain pliers to spread links open. Proceed to attach
one end of chain to FIXTURE LOOP, attached to top
of fixture. Pass the fixture wires through FIXTURE
CHAIN alternating links. Proceed to pass the fixture
wires through the following mounting components
in this order: 1)CANOPY LOCK RING; 2)CEILING
CANOPY 3 CANOPY CHAIN LOOP 4 LOCK
WASHER B and LOCK NUT B 5 NIPPLE 6 LOCK
NUT A and LOCK WASHER A
8.
(2 people recommended for the remaining steps)
Position the fixture under the ceiling mounted outlet
box. Pass LOCK WASHER B over the NIPPLE.
Thread CANOPY CHAIN LOOPonto NIPPLE. Thread
LOCK NUT B down the NIPPLE, against the CANOPY
CHAIN LOOP and snug with pliers. Pass the wires
through the NIPPLE. Take up wire slack and trim wires
so that approx. 6” will remain inside outlet box.
Proceed to attach the top of the FIXTURE CHAIN to
the bottom of the CANOPY CHAIN LOOP.
Using wire connectors (not supplied) connect the
HOUSE GROUND WIRE to the FIXTURE GROUND
WIRE connect the HOUSE WHITE WIRE to the
FIXTURE SUPPLY WIRE (WHITE or RIBBED SIDE);
connect the HOUSE BLACK (or RED) WIRE to the
FIXTURE SUPPLY WIRE(BLACK or SMOOTH SIDE).
Wrap each connection with approved electrical tape.
9. With the proper connections made, proceed to push
the CEILING CANOPY upward over the OUTLET
BOX. Be sure that all wires are carefully tucked into
the OUTLET BOX cavity. Secure canopy against
ceiling by threading CANOPY LOCK RING onto the
CANOPY LOOP.Tighten until snug.
10 Thread the NIPPLE into the mounting hole on the
bottom center of the JUNCTION BOX Hand tighten
until snug Proceed to locate the SCROLLED PART
SMALL TUBE over the end of the NIPPLE in turn
and secure with the FINIAL Hand tighten until snug
11 Position the CRYSTALS onto the hangers on the
FINIAL SCROLLED PART SUPPORT ARMS and
DECORATIVE ARMS as shown
12.Position the CANDLE COVER over the SOCKET as
shown Put the CAPS onto the top end of the
CANDLE COVER Install the correct bulbs referring to
the maximum wattage affixed to the fixture.
13 Restore power to the installation point ON. Retain
this sheet for future reference.
.
.
.
.
,
,.
..
.
.
.
..
.
..
.
.
;) ;)
;) ; )
.
;
.
.
.,
..
.
,,
.
.
.
.
.
Making the connections:
Please note that
there are two kinds of CRYSTALS
ASSEMBLY/ INSTALLATION INSTRUCTIONS
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!
5 Thread the FIXTURE LOOP onto the nipple on the
top end of the CENTER COLUMN and tighten until
snug