Installation & Assembly

ManualsBrandsAstoria Grand ManualsLantern Outdoor Wall LightingFalnaglass 3 - Bulb Beveled Glass Outdoor Wall Lantern

Part

Description

Quantity

A Crossbar

1pc.

2 pcs.

Finial Assembly

Hex Nut

Lock Washer

Package Contents

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing

the fixture. We strongly recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool

before removal. Do not subject glass parts to any shock while in operation or shattering may result.

Mounting Ball

Mounting Screw

1of7

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wire

strippers,electricaltape,safetyglasses.

EstimatedAssemblyTime:20-30 minutes

BulbRecommended: (3)CandelabraBase 60W Maximum

Preparation:Identifyandinspectallpartsbeforebeginninginstallation.Checkpackage

contentlistanddiagramsbelowtobesureallpartsarepresent.Ifanypartsaremissing

ordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomer

serviceforreplacementparts.

1pc.

Fixture Body

4 pcs.

8 pcs.

Lock Screw

Large Glass Panel

4 pcs.

Small Glass Panel

4 pcs.

Loog Tab

4 pcs.

Short Tab

Assembly Instruction

Summary of content (7 pages)

PAGE 1
Assembly Instruction Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Bulb Recommended: (3) Candelabra Base 60W Maximum Estimated Assembly Time: 20-30 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
FINISH: MYSTIC BLACK 14” 11” 12” 25” 11” (3)60W Candelabra base bulbs (not Supplied) NO. PART NUMBER NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2" REPLACEMENT PART DESCRIPTION 2of7 REQ.
PAGE 3
Assembly Instruction STEP 1 - Remove Glass Frame from Fixture Hood Fixture Body A. Prior to assembly, remove the Glass Frame from the Fixture Hood by unscrewing the Hex Coupling. Remove the packaging material inside of the Glass Frame. Fixture Hood Frame Figure 1 Hex Coupling STEP 2 - Attach Mounting Screws, Lock Washers and Hex Nuts to Crossbar Lock Washer Mounting Screw Hex Nut A. Line up a set of holes on the Crossbar (A) and Holes on the backplate of the Fixture Body (F). B.
PAGE 4
Assembly Instruction STEP 4 - Attach Lanyard Button Stop A. The purpose of the lanyard is to provide the installer a means to support the fixture from the junction box while connecting the electrical wires. This enables the fixture to hang from the junction box and your hands are free to make the wire connections. B. Turn the Button Stop so it may be inserted into the crossbar slot. Make sure the Button Stop is completely inside the crossbar.
PAGE 5
Assembly Instruction STEP 6 - Attach Fixture Body to Mounting Screw Figure 7 A. Place the backplate of the Fixture Body (G) over the Mounting Screws (B) and secure with Mounting Balls (E). Hand tighten until snug. Mounting Screw Backplate Mounting Ball STEP 7 - Install Bulb A. This fixture uses standard bulb with a candelabra screw base. Maximum 60 watts. B. Insert bulb and screw snugly into place. Bulb Socket Figure 8 STEP 8 - Attach Glass Short Tab Lock Screw A.
PAGE 6
Assembly Instruction STEP 9 - Attach Glass Frame to Fixture Hood A. Place the Glass Frame over the end of the Stem on the bottom center of the Junction Box. Attach to the Fixture Hood. Secure by threading the Hex Coupling onto the Stem and tighten until snug. Fixture Hood Junction Box Stem Glass Frame Figure 10 Hex Coupling STEP 10 - Assemble Strut Member and Finial Figure 11 A. Remove the Strut Member and the Nipple from the Finial. B.
PAGE 7
Assembly Instruction STEP 11 - Apply Silicone Sealer to Backplate Outdoor Fixture Backplate A. Make sure exterior wall surface and fixture backplate are free of dirt before applying caulk. Using exterior grade caulk, start on one side of fixture backplate and follow contour, where the fixture backplate meets the exterior wall surface upward. Proceed to caulk over top of backplate and down other side. Do not caulk bottom of fixture backplate to ensure proper moisture drainage.