RB Robotic Pool Cleaner Installation and Operating Instructions Product 11712 Product Inst 320
Dear Customer, Thank you for choosing our product to clean your pool. We hope that you will enjoy using your new robot to maintain your swimming pool for years to come. Before you begin to use your robot, please take a few minutes to carefully read these operating instructions. Again, thank you for choosing our product.
Operating the pool cleaner 1. Place the power supply (transformer) at least 3.6 meters / 11.8 feet from the pool and at least 12 cm / 4 Inch above the surface (fig.1). The transformer will supply low voltage to the cleaner. 2. Uncoil the cable.(fig.1a) unit 4. Place the unit in the water. Turn the unit side to side in the water to allow air to escape from the body and then let the cleaner sink to the bottom of the pool (fig.3). Then, spread the cable over the surface of the pool as evenly as possible (fig.
Operating the pool cleaner Grounding The power supply must be connected to a grounded 3 conductor socket. The mains power supply must be connected via a GFCI (ground fault circuit interrupter) or RCD (residual current device) having a rated residual operating current not greater than 30mA. Fuse The fuse must be changed by an authorized service agent or trained and qualified person only. For continued protection against risk of fire, replace only with the same type and rating of fuse.
Operating the pool cleaner a. Power LED The blue LED flashes when the power supply is in standby mode and lights continuously when the pool cleaner is operating.The power button switches between ON and STANDBY b. "POWER" button The button switches between "ON" and "STANDBY". IMPORTANT- After every cycle the pool cleaner will automatically go to "standby".
Maintenance and adjustment CLEAN THE FILTER BAG AFTER EVERY CLEANING CYCLE smooth surface a. Unplug the power supply. (Please keep the plug away from contact with water) b. If the unit is in the pool, gently pull the cleaner toward you using the cable until the handle is within reach. Use the handle (not the cable) to pull the cleaner out of the pool after allowing most of the water to drain from the unit. c.
Maintenance and adjustment Filter bag Screws 30°C / 85°F outlet top propeller label (continued from the previous page) d. Remove the filter bag from the support bars, turn it inside out and wash off all the dirt with a garden hose or in a sink. Squeeze the bag gently until the rinse water is clear. If necessary, machine wash the bag using only cold water with NO DETERGENT! (fig.5) e. Re-install the bag on the support bars with the label in the center of one of the long sides of the bottom lid (5a) f.
Troubleshooting Guide PLEASE CHECK THE FOLLOWING BEFORE CALLING YOUR SERVICE CENTER Before troubleshooting, the pool cleaner must be disconnected from the power supply and the power supply must be unplugged from the electrical outlet to prevent damage to the unit and possible personal injury. For reference numbers, consult the parts list diagram located on the last page of the instructions. 1. Unit does not pump water or move: a) Check to see if electric outlet (22) has power.
16 2 1 3 4 5 6 7 22 24 23 Parts List the pool cleaner Operating 20 1. Outlet Top and propeller 2. Pump Motor 3. Drive Motor 4. Handle Locking Bracket 5. Pulley Assembly 6. Drive Belt 7. Drive Track 8. Body Assembly 9. Filter Screen 10. Side Plate 11. PVA Brushes 12. Filter Bag 13. Bottom Lid Assembly 14. Handle Assembly 15. Cable Assembly 16. Power Supply (Transformer) 17. Transformer Socket 18. Wheel Tube Assembly 19. “OFF” button 20. LED 21. “ON” button 22. Power Cord (Outlet) 23.
WARRANTY TERMS AND CONDITIONS Astral Pool Australia Pty Ltd (ABN 97 007 284 504) ("Astral Pool") provides the following warranty in relation to its Robotic Pool Cleaners. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
WARRANTY CLAIMS 1.If a fault covered by warranty occurs, the customer must first contact AstralPool at the contact address listed below, or an Authorised AstralPool Service Agent. 2. Any warranty claim must be accompanied by: (a) proof of purchase; (b) full details of the alleged defect; and (c) appropriate documentation (such as historical and maintenance records). 3. The customer must make the Product available to AstralPool or its Authorised AstralPool Service Agent for inspection and testing.
EXCLUSIONS AND LIMITATIONS EXCLUSIONS The warranty will not apply where: (a) the customer is in breach of the Terms and Conditions of Sale; (b) the Product was used for a purpose other than one it was intended for; (c) the Product was repaired, modified or altered by any person other than AstralPool; (d) the Product has not been installed, maintained and/or operated in complete compliance with the installation and operating instructions and any instructions by AstralPool; (e) the Product has been subject t
Melbourne 39-45 Cyber Loop Dandenong VIC 3175 P: 03 8796 8600 Townsville 17 Auscan Crescent Garbutt QLD 4814 P: 07 4796 0100 Sydney Seven Hills 2/2 Welder Road Seven Hills NSW 2147 P: 02 9853 2100 Sydney Moorebank 6/30 Heathcote Road Moorebank NSW 2170 P: 02 8778 9500 Adelaide 13 William Street Mile End South SA 5031 P: 08 8152 7600 Brisbane 1/27 Millenium Place Tingalpa QLD 4173 P: 07 3308 5400 Perth 97 Sheffield Road Welshpool WA 6106 P: 08 9350 2600 Gold Coast 1/28 Export Drive Molendinar QLD 4214
