–– VSS-113 SECURITY SYSTEM FEATURING KEYLESS ENTRY OWNER’S MANUAL ® 2006 ASTROFLEX ELECTRONICS
Table of contents What is included ...................................................................................................................................................................... 1 Important information ............................................................................................................................................................ 1 System maintenance.............................................................................................................
What is included One control module A pair of three-button transmitters A Stinger® Doubleguard® dual-stage shock sensor (on-board the control module) The Revenger® Soft Chirp® six-tone programmable siren Blue status LED indicator light A push-button Valet button Failsafe® Starter Kill ready circuitry (may require extra labour) HF+ external receiver/antenna Important information Congratulations on the purchase of your state-of-the-art vehicle security system.
Transmitter functions The system uses a computer-based learn routine to learn the transmitter buttons. This makes it possible to assign any transmitter button to any system function. The transmitter initially comes programmed with Standard Configuration, but may also be customized by an authorized dealer. The buttons in all of the instructions in this manual correspond to a Standard Configuration transmitter. STANDARD CONFIGURATION Button Pressing duration Action Confirmations 1 sec.
PASSIVE ARMING The system also can be programmed to arm itself automatically (called passive arming). If the system is programmed for passive arming, it will automatically arm 30 seconds after the ignition is turned off and the system “sees” you leave the vehicle by opening and closing a door. Whenever the system is in its 30-second passive-arming countdown, the status LED will flash twice as fast as it does when the system is armed.
Press a fourth time within five seconds: The siren chirps four times followed by a long chirp. Zones 2 and 4 are now bypassed. Press a fifth time within five seconds: The siren chirps five times followed by a long chirp. All input zones, except the ignition, are now bypassed. Continued pressing of will begin the Multi-Level Security Arming cycle over again. Note: Multi-Level Security Arming only applies to a single arming cycle.
DISARMING WITHOUT A TRANSMITTER This feature allows you to disarm the security system without the remote transmitter should it be lost or damaged. In order to disarm the system without a remote transmitter, you must have the vehicle’s ignition key and know where the Valet button is located. Be sure to check with the installer for the location and the number of presses of the Valet button required to disarm the system. To disarm the security system, turn the ignition to the ON position.
security system will not arm, even with the remote transmitter, but all convenience functions (door locks, trunk release, etc.) will continue to work normally. To enter or exit Valet® Mode: 1. Turn the ignition on. 2. Turn the ignition off. 3. Press and release the Valet® switch within 10 seconds. To enter or exit Valet Mode using the transmitter: 1. Open any vehicle door. 2. Press . 3. Press or 4. Press again. .
Doors and ignition are covered by NPC® differently; if the alarm is triggered by an open door or ignition on cycle for three full cycles, the doors will be bypassed until the trigger ceases. Note: Arming and disarming the system does not reset this function! The only ways to reset a bypassed zone are for it to not trigger for 60 minutes, or to turn on the ignition. If testing your system, it is important to remember that the NPC programming can cause zones to be bypassed and appear to stop working.
SYSTEM STATUS CHIRPS The siren will chirp when arming/disarming the system. The pattern of chirps will audibly report the system’s status as described below. Action Number of Chirps Description Arm 1 System armed Arm 1 (3 second delay), 1 System armed with zone active Disarm 2 System disarmed Disarm 4 System disarmed with zone violation report Disarm 5 System disarmed NPC® active TABLE OF ZONES The zone number is the number of LED flashes used by the system to identify that input.
Code hopping Both the receiver and transmitters use mathematical formulas called algorithms to change their codes each time the transmitter is used. This technology has been developed to increase the security of the unit. The control unit knows what the next codes should be. This helps to keep the transmitter “in sync” with the control unit even if you use the remote control out of range of the vehicle.
Power saver mode Your system will automatically enter Power Saver Mode while armed or in Valet Mode, after a long period of time in which no operation has been performed. This lowers the current draw to the vehicle’s battery. Power Saver Mode takes over under the following conditions: Power Saver when the system is armed: After the system has been armed for 24 hours, the LED will flash at half its normal rate, decreasing the system’s current draw.
been left ajar when leaving the vehicle. Forced passive arming ensures that the security system will be armed in every situation. Note: When the system passively arms after one hour, the entry point that has been left open, and anything connected to the same zone, is bypassed and cannot trigger the system. However, the remaining inputs to the system are fully operational.
Installation options The system has many options that may require extra parts and labor. Some of the possibilities are listed here. Progressive unlocking: In most cars with electric power door locks, the system can be configured so that when the system is disarmed, only the driver’s door unlocks. A second press of the button unlocks the other doors. Vehicle Recovery System (VRS®): VRS® is an anti-carjacking device designed to help in the safe recovery of your vehicle in case of a carjacking.
vehicle, the system will trigger as the door is opened and closed. This is how the system works to combat intersection carjacking. To protect against parking lot carjacking, arm the VRS® before leaving the vehicle. The system will now trigger automatically the next time you or anyone drives the vehicle. This helps to protect the vehicle if someone takes your keys and remote transmitter by force in a parking lot.
If the system has entered the triggered sequence (siren has begun chirping), pressing the disarm button of the transmitter will not disarm VRS®. To disarm the VRS® during a VRS® trigger sequence: 1. Turn the ignition on. 2. Press the Valet switch the pre-programmed number of times to disarm the VRS® system. Note: If the VRS® system has begun its chirping sequence, the ignition must be turned off, then on to disarm.
Trigger or Triggered Sequence: This is what happens when the alarm “goes off” or “trips”. The triggered response of your system consists of the siren sounding and parking light flashing for the programmed duration. Valet Switch: A small push-button switch mounted somewhere inside the vehicle. It is used to override the alarm when a transmitter is lost or damaged, or to enter or exit Valet mode.
REFERENCE GUIDE You can lock the doors, and arm the system by pressing the TO ARM AND LOCK (1) button on your transmitter for one second. When the system arms, you will hear a short siren sound, or chirp, and the parking lights will flash once. If the vehicle’s power door locks have been connected to the system, the doors will lock (1).