AK34 5U Tower Chassis Kit User Guide
Disclaimer/Copyrights Copyright © 2003 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Disclaimer/Copyrights ..................................................................... ii Contents ......................................................................................... iii Notices ............................................................................................ v Safety information .......................................................................... vi About this guide .............................................................................
Contents 2.7 2.8 2.6.2 Installing a long expansion card .......................... 2-17 2.6.3 Removing an expansion card .............................. 2-18 Removable components ................................................... 2-19 2.7.1 Chassis fan .......................................................... 2-19 2.7.2 Roller wheels ....................................................... 2-20 2.7.3 Power supply modules ......................................... 2-21 Connecting the cables ................
Notices Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical Safety IMPORTANT • Before installing or removing signal cables, ensure that the power cables for the system unit and all attached devices are unplugged. • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing any additional devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected.
About this guide Audience This user guide is intended for system integrators, and experienced users with at least basic knowledge of configuring a server. Contents This guide contains the following parts: 1. Chapter 1: System overview This chapter describes the general features of the AK34 barebone server. It includes sections on front panel and rear panel specifications. 2.
ASUS Contact Information ASUSTeK COMPUTER INC. (Asia-Pacific) Address: General Tel: General Fax: General Email: 150 Li-Te Road, Peitou, Taipei, Taiwan 112 +886-2-2894-3447 +886-2-2894-3449 info@asus.com.tw Technical Support MB/Others (Tel): Notebook (Tel): Desktop/Server (Tel): Support Fax: Web Site: +886-2-2890-7121 (English) +886-2-2890-7122 (English) +886-2-2890-7123 (English) +886-2-2890-7698 www.asus.com.
This chapter describes the general features of the AK34 chassis kit. It includes sections on front panel, rear panel, and internal features.
1.1 Package contents 1.1.1 ASUS AK34 chassis kit The AK34 models are distinguished by the type of bundled HDD tray and power supply. Refer to the following table to check the items that came with the model you purchased. Model AK34-R5 AK34-S4 AK34-S3 HDD tray type IDE/SCSI IDE/SCSI IDESCSI Power supply unit(s) 500W redundant (2 units) 450W single 320W single 1.1.2 Standard items 1.
1.2 Overview The AK34 chassis kit is designed for easy configuration, flexibility, and high reliability. The chassis may be set up as standalone or rack-mount. Flexible expansion Front panel Inside the stylish front bezel secured by a lock, the front panel features easily accessible drives bays: • a floppy drive bay (floppy drive already installed) • three 5.
1.3 Front panel features The AK34 chassis kit displays a stylish front bezel with lock. The bezel covers the system components on the front panel and serves as security. Open the bezel to access the front panel components. The power and reset buttons, LED indicators, CD-ROM drive, floppy drive, and two USB ports are located on the front panel. For future installation of 5.25-inch devices, two drive bays are available. Security lock CD-ROM drive Floppy disk drive 2 empty 5.
1.4 Rear panel features The rear panel includes a slot for the motherboard rear I/O ports, six fulllength expansion slots, a chassis lock and intrusion switch, a vent for the system fan, and either two redundant power supply modules or a standard power supply module.
1.5 Internal features The chassis kit includes the basic components as shown in the picture below. The power supply area differs depending on the power supply module that came with the server you purchased. System with standard power supply module 2 1 6 3 5 4 1. 2. 3. 4. 5. 6. Power supply module 5.
1.6 LED information The following table describes the LED indicators on the server front and rear panels.
1-8 Chapter 1: Product introduction
Chapter 2 Hardware setup This chapter describes the internal hardware components and provides the installation procedures for additional system components.
2.1 Preparation Before proceeding, prepare everything that you might need to facilitate installation. 2.1.1 Tools to use 1. Phillips head screw driver 2. Flat head screw driver 2.1.2 System components and devices to install The following items are the basics that you need to install into the chassis kit. You may need to install other devices depending on your configuration. 1. 2. 3. 4.
2.2 Removing and installing the side cover 2.2.1 Removing the cover 1. Loosen the two thumb screws that secure the side cover. 2. Slide the side cover for about half an inch toward the rear until it is disengaged from the chassis. 1 2 2.2.2 Installing the cover 1. Match and insert the hooks of the cover to the elongated holes on the side of the chassis. All the six hooks (three each on the top and bottom) of the cover must properly fit the designated holes. 2.
2.3 Motherboard installation This section only describes how to install a supported motherboard into the AK34 chassis kit. Refer to the motherboard user guide for instructions on installing specific motherboard components. 2.3.1 Motherboard dimensions 12 in (30.5 cm) This chassis kit supports an ASUS motherboard that measures 12x12 inches (30.5 x 30.5 cm). Motherboards of smaller sizes will fit into the system chassis. Refer to the motherboard user guide for more information on the system requirements.
2.3.2 Placement direction and screw holes Align the holes on the motherboard (indicated by white circles in the picture below) to the corresponding standoffs on the motherboard metal plate inside the chassis. Place screws through the designated holes to secure the motherboard to the chassis. Refer to the motherboard user guide for the specific number of screws that you need to use.
2.3.3 Installing the motherboard 1. Remove the temporary metal shield on the rear panel (beside the chassis fan) that covers the rear I/O slot opening. 2. Install the rear I/O shield that came with the motherboard package. Orient the I/O shield such that the openings for the mouse and keyboard ports are aligned to the top of the chassis fan. 1 Temporary metal shield on the I/O slot opening Mouse/Keyboard port openings 2 I/O shield 3.
2.4 Installing 5.25-inch drives If you have previously used and powered up the system, and that it may be connected to an AC power source, make sure to unplug the power cable before installing or removing any system components. Failure to do so may cause severe damage to the motherboard and other system components! Three 5.25-inch drive bays are located on the upper front part of the chassis. A CD-ROM drive that comes standard with the system package occupies the uppermost bay (labeled 1).
2. Pull and swing the left edge of the front panel outward. 3. Unhook the hinge-like tabs from the holes on the right side of the front panel to completely detach the front panel assembly from the chassis. 3 Hinge-like tab 2 2.4.2 Installing a 5.25-inch drive To install a 5.25-inch drive: 1. Remove the metal cover of the bay where you wish to install the drive by pulling the cover outward.
2. From the side of the drive bay, unlock and remove the screwless drive bay lock by turning the knob 45º counter-clockwise until it clicks on the reference point near the “unlocked icon.” Reference point 2 Unlocked icon Knob 3. When released, pull out the drive bay lock and set it aside. 3 4. Carefully insert a 5.25-inch drive (such as a CD/DVDROM drive) into the bay until it is in place. 4 The drive is in place when the screw holes on the drive align with the holes on the side of the bay.
5. Secure the drive to the bay using the screwless drive bay lock that you removed earlier. a. Match the two pegs on the lock to the holes on the drive bay. b. Turn the knob 45º clockwise until it clicks on the reference point near the “locked icon.” 5a Reference point 5b Locked icon 6. On the front panel assembly, detach the plastic bay cover opposite the 5.25-inch drive that you installed by pressing the two hooked tabs on each side of the bay cover.
7. Re-install the front panel assembly (front bezel and front panel cover). a. Insert the four hinge-like tabs to the holes on the right edge of the chassis. b. Swing the front panel to the left and fit the four (4) hooked tabs to the left side of the chassis until the tabs snap in place.
2.5 Installing hard disk drives The five internal hard disk drive (HDD) bays include removable trays for installing 3.5-inch hard disk drives. You need to remove the side cover to access the drive bays. See section “2.2 Removing and installing the side cover” for instructions. Disk drive bay 1 Disk drive bay 2 Disk drive bay 3 Disk drive bay 4 Disk drive bay 5 To install a hard disk drive: 1. Select the drive bay where you wish to install the hard disk.
3. Orient the hard disk drive such that the connectors are parallel to the tray handles. Match and insert the pegs on the left side of the tray to the holes on the drive. Pegs 3 Make sure to place the tray in the correct orientation as shown. 4. The right side of the tray has a spring-lock. Pull the right side of the tray and match its pegs to the holes on the right side of the drive. Return the tray handle in place to secure the drive. 5.
6. Connect one end of a 40-pin IDE cable to the IDE connector on the drive. Connect the other end to an availble IDE connector on the motherboard. 6 Each drive tray has a designated IDE cable to ensure better air flow and cable placement. Make sure to connect the appropriate cable plug to each drive. 7. Connect a 4-pin power plug to the drive power connector. 7 8. Repeat steps 1 to 7 to install other hard disk drives.
2.6 Installing or removing an expansion card The chassis is designed with a screwless expansion slot frame on the rear panel. This design feature allows you to install or remove an expansion card in less steps. Make sure to unplug the power cord before installing or removing expansion cards. Failure to do so may cause physical injury, and damage to the card and motheboard components! 2.6.1 Installing a standard size expansion card To install an expansion card: 1. Release the card lock. a.
3. Install the expansion card making sure that it is properly seated on the slot. 3 LOCK 4. Press the end of the card lock marked “LOCK” to secure the card on the slot. A light click indicates that the card is locked in place. 4 Refer to the card documentation for the card configuration details, and to the motherboard user guide in case you need to configure any jumpers after installing the expansion card.
2.6.2 Installing a long expansion card If you are installing a long expansion card, such as some types of RAID cards, use the plastic card support located near the front of the chassis (under the backplane board) to keep the expansion cards firmly seated on the slots. This card support has individual card guides that correspond to each expansion slot. Plastic long-card support To install a long expansion card: 1. Position the expansion card above the PCI slot that you wish to use. 2.
2.6.3 Removing an expansion card To remove an expansion card: 1. Release the card lock. a. Press the card lock lever. b. The card lock flips up. Card lock lever Card lock 1a 1b 2. Pull out the card from the PCI slot. 2 3. Press the end of the card lock marked “LOCK” to return it in place.
2.7 Removable components When installing or removing system devices, you may need to remove previously installed components. This section describes how to remove these components. 2.7.1 Chassis fan To remove the 12-cm chassis fan: 1. Disconnect the 3-pin fan cable from the connector on the motherboard. 2. Use a flat screwdriver to push the pin locks on the four corners of the fan from the inside of the chassis. Chassis fan cable Pin lock (tail-end) 3. Pull out the pin locks from the rear panel. 4.
2.7.2 Roller wheels The chassis comes with four roller wheels for convenient transport. Each wheel has a brake lock to stabilize the chassis in place. To remove the chassis wheels: 1. Lay the chassis in its side. 2. Use a Phillips screwdriver to remove the screws that secure the wheels to the bottom of the chassis. Brake lock Remove the chassis roller wheels if you wish to mount the system to a rack. Refer to the Rackmount Kit manual for more information.
2.7.3 Power supply modules The redundant power model has two power supply modules. These hot swap power modules can be removed or installed while the system is powered ON. Only one power module is necessary to provide power to the system. However, it is recommended to have two redundant power supply modules. In case one of the power modules fails, the other one keeps providing sufficient power to the system. This eliminates system down time and data loss.
2.8 Connecting the cables The chassis includes power and signal cables that you need to connect to the motherboard and to the devices that you will install. Most of the cables for the chassis kit are already connected upon shipment. When installing system devices and connecting cables, make sure that all cables are routed properly for better system stability and performance. Refer to the picture below when arranging cables. 2 1 3 4 5 6 7 8 9 Standard cables connected to the motherboard 1. 2. 3. 4. 5.
This appendix lists the common problems that you may encounter while using the server. It lists the possible causes of the problems and offers solutions. You may refer to this part and try to solve simple problems before calling customer support.
A.1 Simple fixes Some problems that you may encounter are not due to defects on the system or the components. These problems only requires simple troubleshooting actions that you can perform by yourself. Problem A-2 Action The power LED on the server or on the monitor do not light up 1. Check the power cable connection on the system rear panel if properly connected. 2. Make sure that the power cables are connected to a grounded power outlet.
Problem Action The system continuously beeps after it was turned on 1. Check the memory modules and make sure you installed the DIMMs the system supports. 2. Make sure that the DIMMs are properly installed on the sockets. 3. Check if it has a VGA ouput. The message “Non-system disk or disk error” appears 1. Check if a bootable HDD is active. 2. Check if the HDDs are properly installed. On SCSI models, make sure that the cables are properly connected to the SCSI connectors on the backplane.
A-4 Appendix: Troubleshooting
