P1-P5945G/P2-P5945G ASUS PC (Desktop Barebone) User Guide
E2798 First Edition October 2006 Copyright © 2006 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Table of contents Notices................................................................................................. vi Safety information...............................................................................vii About this guide..................................................................................viii System package contents..................................................................... x Chapter 1: System Introduction 1.1 Welcome!..........................................
Table of contents Chapter 3: 3.1 Installing an operating system............................................... 3-2 3.2 Powering up........................................................................... 3-2 3.3 Support CD information......................................................... 3-2 3.4 3.3.1 Running the support CD........................................... 3-3 3.3.2 Utilities menu........................................................... 3-4 3.3.3 ASUS contact information........
Table of contents 5.3 5.4 5.5 5.6 5.7 Main menu............................................................................ 5-13 5.3.1 System Time . ....................................................... 5-13 5.3.2 System Date ......................................................... 5-13 5.3.3 Primary and Third IDE Master/Slave....................... 5-14 5.3.4 IDE Configuration................................................... 5-15 5.3.5 System information..................................
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. • If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
About this guide Audience This guide provides general information and installation instructions about the ASUS P1-P5945G/P2-P5945G system. This guide is intended for experienced users and integrators with hardware knowledge of personal computers. How this guide is organized This guide contains the following parts: 1. Chapter 1: System introduction This chapter gives a general description of the ASUS P1-P5945G/P2P5945G.
Conventions used in this guide WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Instructions that you MUST follow to complete a task. NOTE: Tips and additional information to aid in completing a task. Where to find more information Refer to the following sources for additional information and for product and software updates. 1.
System package contents Check your P1-P5945G/P2-P5945G system package for the following items. If any of the items is damaged or missing, contact your retailer immediately. Item description 1. ASUS book size barebone system with • ASUS motherboard • 200W power supply unit • PCI riser card • CPU fan and heatsink assembly 2. Cables • Power cable and plug • Serial ATA power cable and signal cable • IDE cable (preinstalled) 4. CDs • Support CD • Recover PRO CD 5.
This chapter gives a general description of the ASUS P1P5945G/P2-P5945G. The chapter lists the system features including introduction on the front and rear panel, and internal components.
1.1 Welcome! Thank you for choosing the ASUS P1-P5945G/P2-P5945G! The ASUS P1-P5945G/P2-P5945G is an all-in-one barebone system with a versatile home entertainment feature. The system comes in a stylish mini-tower casing and powered by the ASUS motherboard that supports the Intel® Pentium® D, Intel® Pentium® 4, Intel® Conroe® or Intel® Celeron® processor in the 775-land package.
Open 7 8 9 10 11 12 13 14 1. Optical drive eject button. 2. HDD LED. This LED lights up when data is read from or written to the hard disk drive. 3. Optical drive bay cover. 4. Press to open the front panel cover. 5. Power button. Press this button to turn the system on. 6. Power LED. 7. Reset button 8. MS/MS Pro card slot. 9. CompactFlashTM Card slot. 10. SD/MMC card slot. 11. 4-pin IEEE 1394 port 12. USB 2.0 ports. These Universal Serial Bus 2.0 (USB 2.
1.3 Rear panel The system rear panel includes the power connector and several I/O ports that allow convenient connection of devices. 1 3 5 7 9 11 13 15 17 2 4 6 8 10 12 WARNING! Setting the switch to 115V in a 230V environment or 230V in a 115 environment will seriously damage the system! 14 16 1. Power connector 2. Voltage selector. This switch allows you to adjust the system input voltage according to the voltage supply in your area.
11. LAN (RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN) through a network hub. 12. USB 2.0 ports 1, 2, 3 and 4. These 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. 13. SPDIF Out port This port connects an external audio output device via an optical S/PDIF cable. 14. VGA port 15. DVI-D port 16. Serial port 17.
1.4 Internal components The illustration below is the internal view of the system when you remove the top cover and the power supply unit. The installed components are labeled for your reference. Proceed to Chapter 2 for instructions on installing additional system components. 3 1 2 5 4 8 7 6 1. 2. 3. 4. 1- 5.25-inch optical drive and 3.5 inch hard disk drive cage Front panel cover Power supply unit PCI card riser bracket (connected to the motherboard PCI slot) 5. 6. 7. 8.
Chapter 2 Basic installation This chapter provides step-by-step instructions on how to install components in the system.
2.1 Preparation Before you proceed, make sure that you have all the components you plan to install in the system. Basic components to install 1. Central Processing Unit (CPU) 2. DDR2 Dual Inline Memory Module (DIMM) 3. Expansion card(s) 4. Hard disk drive 5. Optical drive Tool Phillips (cross) screw driver 2.2 Before you proceed Take note of the following precautions before you install components into the system.
2.3 Removing the chassis cover and front panel assembly To remove the chassis cover: 1 1. Remove the cover screws. Keep the screws for later use. 2. Pull the cover slightly toward the rear panel. 2 3 3. Lift the cover, then set aside. To remove the front panel cover 1. Lift the front panel cover hooks outward. 2. Carefully remove the front panel cover, then set it aside.
2.4 Central Processing Unit (CPU) 2.4.1 Overview The motherboard comes with a surface mount LGA775 socket designed for the Intel® Pentium® 4 processor in the 775-land package. 2.4.2 • Check your motherboard to make sure that the PnP cap is on the CPU socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components.
2. Press the load lever with your thumb (A), then move it to the left (B) until it is released from the retention tab. Retention tab A B To prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU. 3. Load lever PnP cap Load plate Lift the load lever in the direction of the arrow to a 135º angle. 4B 4. 5. Lift the load plate with your thumb and forefinger to a 100º angle (4A), then push the PnP cap from the load plate window to remove (4B).
2.4.4 Removing and Installing the CPU fan and heatsink assembly The system package includes a proprietary CPU fan and heatsink assembly to ensure optimum thermal condition and performance. DO NOT replace the proprietary CPU fan and heatsink with other models! To remove the CPU fan and heatsink assembly: 1. Disconnect the CPU fan cable. 2. Loosen the CPU fan and heatsink assembly screws. 3. Lift the CPU fan and heatsink assembly, then set aside.
2.5 Installing a DIMM The system motherboard comes with two Double Data Rate 2 (DDR2) Dual Inline Memory Module (DIMM) sockets. The following figure illustrates the location of the sockets: R 112 Pins 128 Pins DIMM_A1 DIMM_B1 40-pin DDR2 DIMM Sockets 2.5.1 Memory configurations You may install up to 2 GB system memory using 256 MB, 512 MB, and 1 GB DDR2 DIMMs. • Install only identical (the same type and size) DDR2 memory modules. • Install only ASUS-certified memory modules.
Qualified Vendors Lists (QVL) DDR2-533 Model Side(s) Component DIMM Support A B Size Vendor 256MB Kingston KVR533D2N4/256 SS E5116AB-5C-E v v 256MB Kingston KVR533D2N4/256 SS E5116AF-5C-E v v 512MB Kingston KVR533D2N4/512 DS HY5PS56821F-C4 v v 512MB Kingston KVR533D2N4/512 SS HYB18T512800AF3733336550 v v 1G Kingston KVR533D2N4/1G DS D6408TE7BL-37 v v 1G Kingston KVR533D2N4/1G DS 5YD11D9GCT v v 256MB Samsung M378T3253FG0-CD5 SS K4T56083QF-GCD5
DDR2-667 Model Side(s) Vendor 256MB Kingston KVR667D2N5/256 SS E2508AB-6E-E v v 512MB Kingston KVR667D2N5/512 SS D6408TE8WL-27 v v 512MB Kingston KVR667D2E5/512 SS E5108AE-6E-E(ECC) v v 1G Kingston KVR667D2N5/1G DS D6408TE8WL-3 v v 512MB Samsung KR M378T6553CZ0-CE6 SS K4T51083QC v v 512MB Samsung KR M378T6453FZ0-CE6 DS K4T56083QF-ZCE6 v v 512MB Samsung M378T6553CZ3-CE6 SS K4T51083QC-ZCE6 v v 1G Samsung M378T2953CZ3-CE6 DS K4T51083QC-ZCE6
2.5.2 Installing a DDR2 DIMM Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components. 2 1. Unlock a DDR2 DIMM socket by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. DDR2 DIMM notch 1 1 Unlocked retaining clip A DDR2 DIMM is keyed with a notch so that it fits in only one direction.
2.6 Expansion slots This mother board provides two PCI expansion slots, which locate on the PCI raiser card that is connected to its slot on the motherboard. 2.6.1 PCI slots The PCI slots support cards such as a LAN card, SCSI card, USB card, andother cards that comply with PCI specifications. Before installing an expansion card, read the documentation that came with it and make the necessary hardware settings for the card. The length of the PCI card should be less than 150mm on the system. 2.6.
2-12 2. Remove the metal cover opposite the slot that you intend to use. 3. Insert the card connector to the slot, then press the card firmly until it fits in place. Secure the card with a screw. 4. Reinstall the PCI riser card assembly. Make sure that the riser card connector sits properly on the motherboard PCI slot.
Standard interrupt assignments IRQ 0 Standard Function System Timer 1 Keyboard Controller 2 Re-direct to IRQ#9 3 IRQ holder for PCI steering* 4 Communications Port (COM1)* 5 IRQ holder for PCI steering* 6 Floppy Disk Controller 7 Printer Port (LPT1)* 8 System CMOS/Real Time Clock 9 IRQ holder for PCI steering* 10 IRQ holder for PCI steering* 11 IRQ holder for PCI steering* 12 PS/2 Compatible Mouse Port* 13 Numeric Data Processor 14 Primary IDE Channel 15 Secondary IDE Chann
2.7 Installing an optical drive and reinstalling the storage drive assembly Refer to the instructions in this section if you wish to install a new optical drive. Follow these steps to install an optical drive: 1. 2. Turn the storage drive assembly upside down with the 3.5-inch bay on top of the 5.25-inch bay. Insert the optical drive upside down to the 5.25-inch bay, then secure it with two screws on both sides. 2 3. Turn the storage drive assembly, insert the hard disk drive upside down to the 3.
Follow these steps to reinstall the storage drive assembly: Before reinstalling the storage drive assembly, connect the IDE/SATA and power plugs to the IDE/SATA and power connectors at the back of the drives. 1. Connect the black plug of the IDE cable to the optical drive, then the gray plug to the hard disk drive. If you have the SATA HDD, connect the SATA cable to the SATA HD. 2. Connect the 4-pin power plugs to the power connectors at the back of the drives. 3.
2.8 Installing the foot stand To install the foot stand: 1. Match the foot stand hooks to the holes on the chassis. 2. Pull the foot stand to the direction of the arrow until the lock clicks in place. To remove the foot stand, lift the lock, then slightly push the foot stand to the direction of the rear panel until it disengages from the chassis.
2.9 Reinstalling the front panel cover To reinstall the front panel cover: 1. Insert the front panel cover tabs to the holes at the right side of the chassis, then close. 2. Insert the front panel cover hooks to the chassis tabs until the front panel cover fits in place.
2.9 Reinstalling the cover To reinstall the cover: 2-18 1. Install the cover to the chassis. Make sure the cover tabs fit the chassis rails. 1 2. Push the cover toward the front panel until it fits in place. 2 3. Secure the cover with two screws.
Chapter 3 Starting up This chapter helps you power up the system and install drivers and utilities from the support CD.
3.1 Installing an operating system The barebone system supports Windows® 2000/XP operating systems (OS). Always install the latest OS version and corresponding updates so you can maximize the features of your hardware. Because motherboard settings and hardware options vary, use the setup procedures presented in this chapter for general reference only. Refer to your OS documentation for more information. 3.2 Powering up Press the system power button ( ) to enter the OS. Press to turn ON the system 3.
3.3.1 Running the support CD To begin using the support CD, place the CD in your optical drive. The CD automatically displays the Drivers menu if Autorun is enabled in your computer. Click an icon to display support CD/motherboard information Click an item to install If Autorun is NOT enabled in your computer, browse the contents of the support CD to locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run the CD.
3.3.2 Utilities menu The Utilities menu shows the applications and other software that the motherboard supports. ASUS InstAll-Installation Wizard for Utilities Installs the ASUS InstAll-Installation Wizard Utilities. ASUS PC Probe II This smart utility monitors the fan speed, CPU temperature, and system voltages, and alerts you of any detected problems. This utility helps you keep your computer in healthy operating condition.
3.3.3 ASUS Contact information Click the Contact tab to display the ASUS contact information. You can also find this information on the inside front cover of this user guide.
3.4 Software information Most of the applications in the support CD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software for more information. ASUS PC Probe II PC Probe II is a utility that monitors the computer’s vital components and alerts you of any problem with these components. PC Probe II senses fan rotations, CPU temperature, and system voltages, among others.
Button Function Opens the Configuration window Opens the Report window Opens the Desktop Management Interface window Opens the Peripheral Component Interconnect window Opens the Windows Management Instrumentation window Opens the hard disk drive, memory, CPU usage window Shows/Hides the Preference section Minimizes the application Closes the application Sensor alert When a system sensor detects a problem, the main window right handle turns red, as the illustrations below show.
Hardware monitor panels The hardware monitor panels display the current value of a system sensor such as fan rotation, CPU temperature, and voltages. The hardware monitor panels come in two display modes: hexagonal (large) and rectangular (small). When you check the Enable Monitoring Panel option from the Preference section, the monitor panels appear on your computer’s desktop.
Monitoring sensor alert The monitor panel turns red when a component value exceeds or is lower than the threshold value. Refer to the illustrations below. Small display Large display WMI browser Click to display the WMI (Windows Management Instrumentation) browser. This browser displays various Windows® management information. Click an item from the left panel to display on the right panel. Click the plus sign (+) before WMI Information to display the available information.
PCI browser Click to display the PCI (Peripheral Component Interconnect) browser. This browser provides information on the PCI devices installed on your system. Click the plus sign (+) before the PCI Information item to display available information. Usage The Usage browser displays real-time information on the CPU, hard disk drive space, and memory usage. Click to display the Usage browser. CPU usage The CPU tab displays real-time CPU usage in line graph representation.
Memory usage The Memory tab shows both used and available physical memory. The pie chart at the bottom of the window represents the used (blue) and the available physical memory. Configuring PC Probe II Click to view and adjust the sensor threshold values. The Config window has two tabs: Sensor/Threshold and Preference. The Sensor/Threshold tab enables you to activate the sensors or to adjust the sensor threshold values.
This chapter gives information about the motherboard that comes with the system. This chapter includes the motherboard layout, jumper settings, and connector locations.
Motherboard layout 4.2 PS/2KBMS T: Mouse B: Keyboard USBPW12 CD BACK_AUDIO KBPWR USBPW34 COM1 LAN_USB12 USB34 VGA_DVI Realtek RTL8111B ADI AD1988B EATXPWR PCI1 SPDIF_OUT USBPW78 4Mb BIOS Super I/O R CPU_ FAN Intel ICH7 DDR2 DIMM_A1(64 bit,240-pin module) Intel MCH945G PRI_IDE DDR2 DIMM_B1(64 bit,240-pin module) CR2032 3V Lithium Cell CMOS Power VIA VT6308P Cypress CY28551 PANEL SB_PWR 75 A7 BUZZER LG ATX12V RTS5111 MS_CON CLRTC USB7 SATA1 33.
4.3 1. Jumpers Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in the CMOS, which includes the system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the battery. 3. Move the jumper cap from pins 1-2 (default) to pins 2-3.
2. USB device wake-up (3-pin USBPW12, USBPW34, USBPW78) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode).
3. Keyboard power (3-pin KBPWR) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) if you wish to wake up the computer when you press a key on the keyboard (the default is the Space Bar). This feature requires an ATX power supply that can supply at least 1A on the +5VSB lead, and a corresponding setting in the BIOS. KBPWR R 1 2 +5V 2 3 +5VSB (Default) Keyboard Power Setting 4.4 1.
2 IDE connectors (40-1 pin PRI_IDE) PIN1 The onboard IDE connectors are for Ultra DMA 100/66/33 signal cable(s). There are three connectors on each Ultra DMA 100/66/33 signal cable: blue, black, and gray. Connect the blue connector to the motherboard’s IDE connector, then select one of the following modes to configure your device(s). PRI_IDE R NOTE: Orient the red markings (usually zigzag) on the ID ribbon cable to PIN 1.
3. CPU Fan connector (3-pin CPU_FAN) The fan connector support cooling fans of 350 mA~740 mA (8.88 W max.) or a total of 1 A~2.22 A (26.64 W max.) at +12V. Connect the fan cable to the fan connector on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. CPU_FAN +12V GND Tachometer R CPU FAN Connector Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components.
5. ATX power connectors (24-pin EATXPWR, 4-pin ATX12V) These connectors are for ATX power supply plugs. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit.
7. Back audio connector (20-1 pin Back_Audio Connector) AGND_A SENSE SUR BCAZ SUR R BCAZ SUR L SENSE SURB BCAZ SURBR BCAZ SURBL SENSE CN1 BCAZ LEF R BCAZ CEN L R SENSE FRONT BCAZ FRONTR BCAZ FRONT L SENSE LIN1 BCAZ LIN1 R BCAZ LIN1 L SENSE MIC1 BCAZ MIC1R BCAZ MIC1L BACK_AUDIO Back_Audio Connector We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s high‑definition audio capability. 8.
9. System panel connector (6 pin PANEL) This connector supports several chassis-mounted functions. PLED- HD_LED- PA NEL PLED+ HD_LED+ R System Panel Connector The system panel connector is color-coded for easy connection. Refer to the connector description below for details. 4-10 • System power LED (2-pin PLED) This 3-pin connector is for the system power LED. Connect the chassis power LED cable to this connector.
Chapter 5 BIOS setup This chapter tells how to change system settings through the BIOS Setup menus and describes the BIOS parameters.
5.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. ASUS EZ Flash (Updates the BIOS using the motherboard support CD during POST.) 2. ASUS AFUDOS (Updates the BIOS in DOS mode using a bootable USB flash disk.) 3. ASUS CrashFree BIOS 2 (Updates the BIOS using the motherboard support CD when the BIOS file fails or gets corrupted.) 4. ASUS Update (Updates the BIOS in Windows® environment.
5.1.2 AFUDOS utility The AFUDOS utility allows you to update the BIOS file in DOS environment using a bootable USB Flash with the updated BIOS file. This utility also allows you to copy the current BIOS file that you can use as backup when the BIOS fails or gets corrupted during the updating process. Copying the current BIOS To copy the current BIOS file using the AFUDOS utility: • Make sure that the USB Flash has at least 1024KB free space to save the file.
Updating the BIOS file To update the BIOS file using the AFUDOS utility: 1. Visit the ASUS website (www.asus.com) and download the latest BIOS file for the motherboard. Save the BIOS file to a bootable USB Flash. Write the BIOS filename on a piece of paper. You need to type the exact BIOS filename at the DOS prompt. 2. Copy the AFUDOS utility (afudos.exe) from the motherboard support CD to the bootable USB Flash you created earlier. 3.
5.1.3 ASUS CrashFree BIOS 2 utility The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can update a corrupted BIOS file using the motherboard support CD, or the USB Flash that contains the updated BIOS file. • Prepare the motherboard support CD, or the USB Flash containing the updated motherboard BIOS before using this utility.
Recovering the BIOS from the support CD To recover the BIOS from the support CD: 1. Insert the support CD to the optical drive. The utility automatically checks the optical drive for the original or updated BIOS file. The utility then updates the corrupted BIOS file. Checking for CD-ROM... CD-ROM found! Reading file “P5LVM139.ROM”. Completed. Start flashing... DO NOT shut down or reset the system while updating the BIOS! Doing so can cause system boot failure! 4.
5.1.4 ASUS Update utility The ASUS Update is a utility that allows you to manage, save, and update the motherboard BIOS in Windows® environment. The ASUS Update utility allows you to: • Save the current BIOS file • Download the latest BIOS file from the Internet • Update the BIOS from an updated BIOS file • Update the BIOS directly from the Internet, and • View the BIOS version information. This utility is available in the support CD that comes with the motherboard package.
Updating the BIOS through the Internet To update the BIOS through the Internet: 5- 1. Launch the ASUS Update utility from the Windows® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate. The ASUS Update main window appears. 2. Select Update BIOS from the Internet option from the drop‑down menu, then click Next. 3. Select the ASUS FTP site nearest you to avoid network traffic, or click Auto Select. Click Next.
4. From the FTP site, select the BIOS version that you wish to download. Click Next. 5. Follow the screen instructions to complete the update process. The ASUS Update utility is capable of updating itself through the Internet. Always update the utility to avail all its features. Updating the BIOS through a BIOS file To update the BIOS through a BIOS file: 1. Launch the ASUS Update utility from the Windows® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate.
5.2 BIOS setup program This motherboard supports a programmable firmware chip that you can update using the provided utility described in section “2.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you can change the configuration of your computer in the future.
5.2.1 BIOS menu screen Menu items Menu bar Configuration fields General help [11:51:19] [Thu 05/07/2004] Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. System Time System Date Primary IDE Master Primary IDE Slave Third IDE Master IDE Configuration :[Not Detected] :[Not Detected] :[Not Detected] System Information Sub-menu items 5.2.
5.2.4 Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting Main shows the Main menu items. The other items (Advanced, Power, Boot, and Exit) on the menu bar have their respective menu items. 5.2.5 System Time System Date Legacy Diskette A Language [11:10:19] [Thu 03/27/2003] [1.44M, 3.
5.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information. Refer to section “2.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them. System Time System Date Primary IDE Master Primary IDE Slave Third IDE Master IDE Configuration [11:51:19] [Thu 05/07/2004] :[Not Detected] :[Not Detected] :[Not Detected] Use [ENTER], [TAB] or [SHIFT-TAB] to select a field.
5.3.3 Primary and Third IDE Master/Slave While entering Setup, the BIOS automatically detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press to display the IDE device information.
PIO Mode [Auto] Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] Selects the DMA mode. Configuration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] SMART Monitoring [Auto] Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled] 32Bit Data Transfer [Enabled] Enables or disables 32-bit data transfer.
Enhanced Mode Support On [S-ATA] The default setting S-ATA allows you to use native OS on Serial ATA and Parallel ATA ports. We recommend that you do not change the default setting for better OS compatibility. In this setting, you may use legacy OS on the Parallel ATA ports only if you did not install any Serial ATA device. The P-ATA+S-ATA and P-ATA options are for advanced users only. If you set to any of these options and encounter problems, revert to the default setting S-ATA.
5.3.5 System Information This menu gives you an overview of the general system specifications. The BIOS automatically detects the items in this menu. AMIBIOS Version : 0104 Build Date : 08/07/06 Processor Type Speed Count : Genuine Intel(R) CPU 3.
5.4 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Take caution when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. JumperFree Configuration USB Configuration CPU Configuration Chipset Onboard Devices Configuration PCI PnP 5.4.
The following item appears only when you set the AI Overclocking item to [Overlock Profile]. Overlock Options [Overlock 5%] Configuration options: [Overlock 5%] [Overlock 10%] 5.4.2 USB Configuration The items in this menu allows you to change the USB-related features. Select an item then press to display the configuration options. USB Configuration Module Version - 2.24.0-F.4 USB Devices Enabled: 3 Drives USB Function [Enabled] Legacy USB Support [Auto] USB 2.
USB 2.0 Controller Mode [HiSpeed] Allows you to configure the USB 2.0 controller in HiSpeed (480 Mbps) or Full Speed (12 Mbps). Configuration options: [HiSpeed] [Full Speed] BIOS EHCI Hand-off [Enabled] Allows you to enable support for operating systems without an EHCI hand‑off feature. Configuration options: [Enabled] [Disabled] Do not disable the BIOS EHCI Hand-Off option if you are running a Windows® operating system with USB device.
5.4.3 CPU Configuration The items in this menu show the CPU-related information that the BIOS automatically detects. Configure Advanced CPU settings Manufacturer: Brand String: Frequency : FSB Speed : Cache L1 Cache L2 Cache L3 Intel Genuine Intel(R) CPU 3.
Max CPUID Value Limit [Disabled] Enable this item to boot legacy operating systems that cannot support CPUs with extended CPUID functions. Configuration options: [Disabled] [Enabled] Execute Disable Function [Disabled] Enables or disables the Execute Disable function. This item appears only when you install a processor with the Execute Disable function.
5.4.4 Chipset The Chipset menu allows you to change the advanced chipset settings. Select an item then press to display the sub-menu.
Graphic Adapter Priority [PCI/Int-VGA] Allows selection of the graphics controller to use as primary boot device. Configuration options: [Internal VGA] [PCI/Int-VGA] Internal Graphics Mode Select [Enabled, 8MB] Sets the internal graphics mode. Configuration options: [Disabled] [Enabled, 1MB] [Enabled, 8MB] Graphics memory type [Auto] Sets the graphics memory type. Configuration options: [Auto] [DVMT] [FIX] [DVMT+FIX] 5.4.
LAN Option ROM [Disabled] Allows you to enable or disable the option ROM in the onboard LAN controller. This item appears only when the Onboard LAN item is set to Enabled. Configuration options: [Disabled] [Enabled] Serial Port1 Address [3F8/IRQ4] Allows you to select the Serial Port1 base address.
5.4.6 PCI PnP The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices. Take caution when changing the settings of the PCI PnP menu items. Incorrect field values can cause the system to malfunction. Advanced PCI/PnP Settings WARNING: Setting wrong values in below sections may cause system to malfunction.
IRQ-xx assigned to [PCI Device] When set to [PCI Device], the specific IRQ is free for use of PCI/PnP devices. When set to [Reserved], the IRQ is reserved for legacy ISA devices. Configuration options: [PCI Device] [Reserved] 5.5 Power menu The Power menu items allow you to change the settings for the Advanced Configuration and Power Interface (ACPI) and the Advanced Power Management (APM). Select an item then press to display the configuration options. Suspend Mode [Auto] ACPI 2.
5.5.4 APM Configuration APM Configuration Power button Mode [On/Off] Enabled or disable APM.
Power On By PCIE Devices [Disabled] When set to [Enabled], this parameter allows you to turn on the system through a PCI Express LAN card. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Enabled] Power On By PS/2 Keyboard [Disabled] Allows you to use specific keys on the keyboard to turn on the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead.
5.5.5 Hardware Monitor Hardware Monitor AI Quiet [Disabled] CPU Temperature [51ºC/122.5ºF] MB Temperature [41ºC/105.5ºF] CPU Fan Speed (RPM) [2481 RPM] CPU Q-Fan Control [Disabled] VCORE Voltage [ 1.320V] 3.3V Voltage [ 3.345V] 5V Voltage [ 5.094V] 12V Voltage [11.880V] +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit AI Quiet [Disabled] Automatically optimize BIOS setting to Minimize CPU FAN speed according to system loading.
5.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press to display the sub-menu. Boot Settings Boot Device Priority Removable Drives Boot Settings Configuration Security 5.6.1 Boot Device Priority Boot Device Priority 1st Boot Device [Hard Drive] 2nd Boot Device [USB:Generic 2.0Re] 3rd Boot Device [ATAPI CD-ROM] 5.6.2 Removable Drives Specifies the Boot Device Priority sequence from available Removable Drives.
5.6.3 Boot Settings Configuration Boot Settings Configuration Quick Boot [Enabled] Full Screen Logo [Enabled] AddOn ROM Display Mode [Force BIOS] Bootup Num-Lock [On] PS/2 Mouse Support [Auto] Wait For ‘F1’ If Error [Enabled] Hit ‘DEL’ Message Display [Enabled] Interrupt 19 Capture [Disabled] Quick Boot [Enabled] Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system.
Interrupt 19 Capture [Disabled] When set to [Enabled], this function allows the option ROMs to trap Interrupt 19. Configuration options: [Disabled] [Enabled] 5.6.4 Security The Security menu items allow you to change the system security settings. Select an item then press to display the configuration options. Security Settings Supervisor Password User Password : Not Installed : Not Installed to change password. again to disabled password.
After you have set a supervisor password, the other items appear to allow you to change other security settings.
Password Check [Setup] When set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system. Configuration options: [Setup] [Always] 5.7 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items.
Exit & Discard Changes Select this option only if you do not want to save the changes that you made to the Setup program. If you made changes to fields other than System Date, System Time, and Password, the BIOS asks for a confirmation before exiting. Discard Changes This option allows you to discard the selections you made and restore the previously saved values. After selecting this option, a confirmation appears. Select Ok to discard any changes and load the previously saved values.
ASUS P1-P5945G/P2-P5945G 5-37
