Disassembly Procedure 2 Chapter Disassembly Procedure Please follow the information provided in this section to perform the complete disassembly procedure of the notebook. Be sure to use proper tools described before. A SUS W5F Series Notebook consists of various modules. This chapter describes the procedures for the complete notebook disassembly. In addition, in between procedures, the detailed disassembly procedure of individual modules will be provided for your service needs.
Disassembly Procedure B A T T E R Y Battery Module The illustration below shows how to remove the battery module. 1. Press latch to open the battery module, then lift battery module away from the system. H D D M O D U L E H D D M O D U L E HDD Module The illustrations below show how to remove the HDD module from the notebook. Removing HDD Module 1. Remove 2 screws (M2*5L(K)), then remove the HDD door. R E M O V A L M2*5L 2.
Disassembly Procedure S E C O N D M E M O R Y M O D U L E M E M O R Y R E M O V A L Memory Module The W5F Series Notebook have onboard RAM. There is one SO-DIMM sockets for installing SO-DIMM RAM. It can upgrade the total memory size up to 1GB with a 512MB module on each socket. Removing Memory module 1. Remove 2 screws (M2*4L(K)), then remove the Memory cover. M2*4L 2. Pop the module up to a 45° angles, and then pulling out the module in that angle.
Disassembly Procedure C P U M O D U L E R E M O V A L C P U R E M O V A L CPU Module The illustrations below show how to remove the CPU module from the notebook. Removing CPU Module 1. Remove 3 screws (M2*4L(K)), then remove the back cover. M2*4L 2. Remove 4 screws (M2*4L(K)) and disconnect the FAN connector and then take away the Fan Module. M2*4L 3.
Disassembly Procedure O P T I C A L D R I V E Optical Drive Module Remove 3 screws and use tweezers to put the Optical Drive Module out. R E M O V A L M2*4L K E Y B O A R D K / B C O V E R R E M O V A L Keyboard Module The illustration of below shows how to remove the keyboard Removing Keyboard Cover 1. Unlock 3 keyboard latches then pull out the keyboard forward and lay the keyboard on the front side then disconnect the FPC.
Disassembly Procedure T O P C A S E M O D U L E R E M O V A L Top Case Module Removing Top Case Module 1. Disconnect all FPC and 2 screws on the top case. 2. Take away the both hinge cover. 3. Remove 17 screws (M2*6L(K)) on bottom case.
Disassembly Procedure 4. Remove 2 Antenna cables from Wireless LAN Module and organize tables. 5. Separate the Bottom Case from the Top Case module. T O P C A S E M O D U L E Removing Top Case Module 6. Remove 2 screws (M2*5L(K)) from the both hinge.
Disassembly Procedure 7. Separate the top case from the LCD module. 8. Remove 2 screws (M2*3.5L(K)) and take away the LID board. M2*3.5L 9. Remove 2 screws (M2*3.5L(K)) and take away the Power board. M2*3.
Disassembly Procedure 10. Remove 3 screws (M2*3L(K)) & 1 piece of tape then take away the Card reader module. M2*3L 11. Disconnect the FPC on the Touchpad and take it away. 12. Disconnect the Bluetooth antenna and take the Bluetooth module away.
Disassembly Procedure L C D M O D U L E L C D R E M O V A L LCD Module The illustrations below show how to remove and disassemble the LCD module. The module contains LCD panel, Inverter board, LCD Hinge bracket, Hinge cover, LCD front cover, LCD back cover Removing LCD Module 1. Remove 6 rubber pads and 6 screws (M2.5 x 4L) from LCD module. M2.5*4L 2. Prying the inside edges of the top front bezel, then separate it from LCD back cover and take LCD front bezel away. 3.
Disassembly Procedure 4. Remove 4 crews(M2.5*4L(K)) and take away the LCD module . M2.5*4L L C D D I S A S S E M B L Y 5. Remove 2 screws(M2*4L(K)) on the right LCD bracket , and 2 screws on the ilft side to disassemble LCD brackets. M2*4L M2*4L 6. Remove 2 tapes and dissconnect coaxial cable then take it away. 7. Remove 4 screws(M2*4L(K)) on the right & left speaker then take away the both speakers.
Disassembly Procedure 8. Remove 2 screws (M2*3L(K)) and cable. M2*3L 9. Remove the speaker cable and take the Microphone board off. 10. Remove 1 screw (M2*3L(K)) and disconnect the FPC then take the CMOS camera board off. M2*3L 11. Take away the camera cover.
Disassembly Procedure 12. Remove 2 screws (M2*3L(K)) and disconnect the FPC then take the bracket. M2*3L 10. Take away the CMOUS camera. M O T H E R B O A R D M O D U L E M D C M O D U L E Motherboard module The illustrations below show how to disassemble and remove the Motherboard module Removing Motherboard Module 1. Remove 1 screw (M2*3L(K)) on the Motherboard Module.
Disassembly Procedure 2. Remove 2 screws (M2*3L(K)) and disconnect the cable then take away the Modem board. M2*3L 3. Take away the Motherboard board from the left side. 4.
Disassembly Procedure 5. Disconnect the ODO Jack FPC. W I R E L E S S M O D U L E W I R E L E S S M O D U L E R E M O V A L Wireless module The illustrations below show how to disassemble and remove the Wireless module Removing Wireless Module 1. Remove the Wireless LAN module by opening the 2 latches aside, and pull out the module. 2. Remove 1 screw (M2*3L (K)) and take away the TPM board .