使用手冊 Motherboard B85M-G
T8146 第一版 2013 年5 月發行 版權說明 ©ASUSTeK Computer Inc. All rights reserved.
目錄內容 安全性須知........................................................................................................................................ iv 電氣方面的安全性.............................................................................................................. iv 操作方面的安全性.............................................................................................................. iv 華碩 REACH..............................................................................................................
安全性須知 電氣方面的安全性 • 為避免可能的電擊造成嚴重損害,在搬動電腦主機之前,請先將電腦電源線暫時 從電源插槽中拔掉。 • 當您要加入硬體裝置到系統中或者要移除系統中的硬體裝置時,請務必先連接該 裝置的排線,然後再連接電源線。可能的話,在安裝硬體裝置之前先拔掉電腦的 電源供應器電源線。 • 當您要從主機板連接或拔除任何的排線之前,請確定所有的電源線已事先拔掉。 • 在使用介面卡或擴充卡之前,我們建議您可以先尋求專業人士的協助。這些裝置 有可能會干擾接地的迴路。 • 請確定電源供應器的電壓設定已調整到本國/本區域所使用的電壓標準值。若您不 確定您所屬區域的供應電壓值為何,那麼請就近詢問當地的電力公司人員。 • 如果電源供應器已損壞,請不要嘗試自行修復。請將之交給專業技術服務人員或 經銷處理。 操作方面的安全性 • 在您安裝主機板以及加入硬體裝置之前,請務必詳加閱讀本手冊所提供的相關資 訊。 • 在使用產品之前,請確定所有的排線、電源線都已正確地連接好。若您發現有任 何重大的瑕疵,請儘速連絡您的經銷商。 • 為避免發生電氣短路情形,請務必將所有沒用到的螺絲、迴紋針及其他零件收 好,不要遺
關於這本使用手冊 產品使用手冊包含了所有當您在安裝華碩 B85M-G 主機板時所需用到的資訊。 使用手冊的編排方式 使用手冊是由下面幾個章節所組成: • 第一章:產品介紹 您可以在本章節中發現諸多華碩所賦予 B85M-G 主機板的優異特色。利用簡 潔易懂的說明讓您能很快地掌握 B85M-G 主機板的各項特性,當然,在本章節中 我們也會提及所有能夠應用在 B85M-G 主機板的新產品技術。 • 第二章:BIOS 資訊 本章節描述如何使用 BIOS 設定程式中的每一個選單項目來更改系統的組態設 定。此外也會詳加介紹 BIOS 各項設定值的使用時機與參數設定。 提示符號 為了能夠確保您正確地完成主機板設定,請務必注意下面這些會在本手冊中出現 的標示符號所代表的特殊含意。 警告:提醒您在進行某一項工作時要注意您本身的安全。 小心:提醒您在進行某一項工作時要注意勿傷害到電腦主機板元件。 重要: 此符號表示您必須要遵照手冊所描述之方式完成一項或多項軟硬體的安 裝或設定。 注意:提供有助於完成某項工作的訣竅與其他額外的資訊。 跳線帽及圖示說明 主機板上有一些小小的塑膠套,裡面有金屬導線,可以套住選擇區的任二隻
哪裡可以找到更多的產品資訊 您可以經由下面所提供的兩個管道來獲得您所使用的華碩產品資訊以及軟硬體的 更新資訊等。 1. 華碩網站 您可以到 http://tw.asus.com 華碩電腦全球資訊網站取得所有關於華碩軟硬體產品 的各項資訊。 2. 其他檔案 在您的產品包裝盒中除了本手冊所列舉的標準配件之外,也有可能會夾帶有其他 的檔案,譬如經銷商所附的產品保證單據等。 代理商查詢 華碩主機板在台灣透過聯強國際與精技電腦兩家代理商出貨,您請參考下列範例 圖示找出產品的 12 碼式序號標籤(下圖僅供參考),再至 http://tw.asus.com/support/ eService/querydist_tw.
包裝內容物 在您拿到本主機板包裝盒之後,請馬上檢查下面所列出的各項標準配件是否齊全。 主機板 華碩 B85M-G 主機板 排線 2 x Serial ATA 6.0Gb/s 排線 配件 1 x I/O 擋板 公用程式光碟 驅動程式與公用程式光碟 相關文件 使用手冊 若以上列出的任何一項配件有損毀或是短缺的情形,請盡速與您的經銷 商聯絡。 B85M-G 規格列表 中央處理器 支援 LGA1150 插槽 Intel® 第四代 Core™ i7 / Core™ i5 / Core™ i3 / Pentium® / Celeron® 處理器 • 請造訪華碩網站 http:/tw.asus.com 獲取最新的 Intel® 處理器 支援列表 晶片組 Intel® B85 Express 晶片組 記憶體 4 x 記憶體插槽,最高支援 32GB DDR3 1600 / 1333 / 1066MHz, un-buffered、non-ECC 記憶體模組* 支援雙通道記憶體架構 * 請瀏覽 http://tw.asus.
B85M-G 規格列表 網絡功能 Realtek 8111G Gigabit 網絡控制器 音效 Realtek® ALC887-VD2 高保真 8 聲道* 音效編解碼晶片 - 支援音效連接埠偵測(Jack-Detection)、多音源獨立輸出 (multi-streaming)與前面板音效連接埠變換(Jack-Retasking) 功能 * 請使用前面板具備 HD 音效插孔的機殼以支援 8 聲道音效輸出。 USB 4 x USB 3.0 連接埠(2 個位於主板上,2 個位於後面板) 8 x USB 2.0 連接埠(4 個位於主板上,4 個位於後面板) 華碩獨家研發功能 華碩 DIGI+VRM(數位化電源相位設計): - 數位電源控制:CPU 的數位電源設計 - 華碩 3 相電源設計 - 華碩 CPU 電源公用程式 華碩獨家研發功能 - 華碩 EPU - 華碩 USB 3.0 Boost,支援快速 USB 3.
B85M-G 規格列表 內建 I/O 裝置連接埠 1 2 2 4 1 1 1 1 1 1 1 1 1 1 1 x x x x x x x x x x x x x x x USB 3.0 擴充套件排線插槽,可擴充 2 組外接式 USB 連接埠 USB 2.0 擴充套件排線插槽,可擴充 4 組外接式 USB 連接埠 SATA 3.0 Gb/s 裝置連接插座 SATA 6.0 Gb/s 裝置連接插座 機殼開啟警告排針 組態資料清除(CMOS) 中央處理器風扇電源插槽(4-pin) 機殼風扇電源插槽(4-pin) 高保真前面板音效連接排針(AAFP) 系統控制面板連接排針 內置喇叭連接插座 LPT 連接排針 S/PDIF 數位音效連接排針 序列埠連接插座(COM) 24-pin ATX 主機板電源插槽 BIOS 功能 1 x 4-pin ATX 12V 主機板電源插槽 64 Mb Flash ROM、EFI BIOS、PnP、DMI v2.0、WfM2.0、SM BIOS v2.7、ACPI v2.0a、SLP 3.
產品介紹 1.1 1 主機板安裝前 在您動手更改主機板上的任何設定之前,請務必先作好以下所列出的各項預防措 施。 • 在處理主機板上的任何元件之前,請您先拔掉電腦的電源線。 • 為避免產生靜電,在拿取任何電腦元件時除了可以使用防靜電手環之 外,您也可以觸摸一個有接地線的物品或者金屬物品像電源供應器外 殼等。 • 拿取積體電路元件時請儘量不要觸碰到元件上的晶片。 • 在您移除任何一個積體電路元件後,請將該元件放置在絕緣墊上以隔離 靜電,或者直接放回該元件的絕緣包裝袋中儲存。 • 在您安裝或移除任何元件之前,請確認 ATX 電源供應器的電源開關是 切換到關閉(OFF)的位置,而最安全的做法是先暫時拔出電源供應器 的電源線,等到安裝/移除工作完成後再將之接回。如此可避免因仍有 電力殘留在系統中而嚴重損及主機板、周邊裝置、元件等。 1.2 主機板概述 當您安裝主機板到電腦機殼內時,請確認主機板與機殼大小相適應。 請確認在安裝或移除主機板前先拔除電源線,否則可能導致主機板元器 件毀損與對使用者的人身傷害。 1.2.
此面朝向電腦主機 的後方面板 B85M-G 1.2.3 主機板結構圖 1 2 3 3 4 5 19.3cm(7.6in) CPU_FAN KBMS DVI_VGA DIGI +VRM BATTERY AUDIO PCIEX16 RTL 8111G B85M-G 64Mb BIOS PCIEX1_1 Super I/O Intel B85 ® SB_PWR PCIEX1_2 ALC 887 COM SPDIF_OUT CHASSIS USBPWF LPT USB1112 USB1314 AAFP 19 1-2 23.4cm(9.
1.2.4 主機板元件說明 連接插槽 / 跳線選擇區 / 插槽 頁數 1. ATX 主機板電源插槽 (24-pin EATXPWR, 4-pin ATX12V) 1-14 2. 鍵盤和 USB 裝置喚醒 (KB_USBPWB) 1-11 3. 中央處理器 / 機殼風扇電源插槽 (4-pin CPU_FAN, 4-pin CHA_FAN) 1-16 4. Intel® LGA1150 中央處理器插槽 1-3 5. DDR3 記憶體插槽 1-7 6. USB 3.0 擴充套件排線插槽 (20-1 pin USB3_12) 1-18 7. 電力指示燈 (SB_PWR) 1-20 8. Intel® B85 Serial ATA 6.0Gb/s 裝置連接插座 (7-pin SATA6G_1~4 [黃色]) 1-17 9. CMOS 組態資料清除 (3-pin CLRTC) ) 1-10 10. Intel® B85 Serial ATA 3.0Gb/s 裝置連接插座 (7-pin SATA3G_1~2 [咖啡色]) 1-17 11.
• 當您安裝處理器時,請確認所有的電源線都已拔除。 • 確保安裝的是 LGA1150 封裝的處理。請勿將 LGA1155 與 LGA1156 處 理器安裝於 LGA1150 插槽。 • 在您購買本主機板之後,請確認在 LGA1150 插座上附有一個隨插即用 的保護蓋,並且插座接點沒有彎曲變形。若是保護蓋已經丟失或是沒有 保護蓋,或者是插座接點已經彎曲,請立即與您的經銷商聯絡。 • 在 安 裝 完 主 機 板 之 後 , 請 將 隨 插 即 用 的 保 護 蓋 保 留 下 來 。 只 有 LGA1150 插槽上附有隨插即用保護蓋的主機板符合 Return Merchandise Authorization(RMA)的要求,華碩電腦才能為您處理產品的維修與保 修。 •本保固不包括處理器插座因遺失、錯誤的安裝或不正確地移除隨插即用 保護蓋所造成的毀損。 1.3.
4 5 C A B 1.3.
請依照下面步驟安裝處理器的散熱器和風扇: 1 A 2 B B A 3 4 請按照以下的步驟卸除散熱器和風扇: 1 A 2 B B A 1-6 第一章:產品介紹
1.4 系統記憶體 1.4.1 概述 本主機板配備四組 240-pin DDR3(Double Data Rate,雙倍資料傳送率)記憶體插 槽。DDR3 記憶體模組和 DDR 或 DDR2 記憶體模組不同,請勿將 DDR 或 DDR2 記憶 體模組 安裝在 DDR3 記憶體插槽。 下圖所示為 DDR3 記憶體插槽在主機板上的位置。 DIMM_B1 DIMM_B2 DIMM_A1 DIMM_A2 依據 Intel® CPU 規格,建議您安裝電壓低於 1.65V 的記憶體模組以保護 CPU。 通道 插槽 通道 A DIMM_A1 與 DIMM_A2 通道 B DIMM_B1 與 DIMM_B2 B85M-G B85M-G 240-pin DDR3 DIMM sockets 1.4.
•記憶體模組預設頻率依據 SPD 而變化,這是從記憶體模組存取資料的 標準方法。 • 在全負載(4 DIMM)或超頻設定下,請使用更有效的散熱系統以確保 系統穩定性。 • 請造訪華碩網站(http://tw.asus.com)獲得最新得記憶體合格供應商列表 (QVL)。 1.4.3 安裝記憶體模組 安裝 / 取出記憶體模組或其他的系統元件之前,請先暫時拔出電腦的電源 變壓器。如此可避免一些會對主機板或元件造成嚴重毀損的情況發生。 請依照下面步驟安裝記憶體模組: 2 記憶體模組缺口 1. 先將記憶體模組插槽二端的固定卡 榫扳開。 2. 將記憶體模組放在插槽上,使缺口 對準插槽的凸起點。 DDR3 記憶體模組金手指部 份均有缺口設計,因此只能 以一個固定方向安裝到記憶 體模組插槽中。請勿強制插 入以免損及記憶體模組。 1 1 向外扳開插槽兩端的卡榫 3 3. 最後緩緩將記憶體模組插入插槽 中,若無錯誤,插槽二端的卡榫會 因記憶體模組安裝而自動扣到記憶 體模組一側的凹孔中。 卡榫會在記憶體模組正確安裝後自動扣上 1.4.4 取出記憶體模組 請依照以下步驟取出記憶體模組: 1.
2 在壓下固定卡榫取出記憶 體模組的同時,您可以用 手指輕輕地扶住記憶體模 組,以免彈出而損及記憶 體模組。 1 1 2. 再將記憶體模組由插槽中取出。 1.5 記憶體模組缺口 擴充插槽 考慮到未來會擴充系統機能的可能性,本主機板提供了擴充插槽,在接下來的次 章節中,將會描述主機板上這些擴充插槽的相關資訊。 安裝 / 移除任何擴充卡之前,請暫時先將電腦的電源線拔出。如此可免除 因電氣殘留於電腦中而發生的意外狀況。 1.5.1 安裝擴充卡 請依照下列步驟安裝擴充卡: 1. 在安裝擴充卡之前,請先詳讀該擴充卡的使用說明,並且要針對該卡作必要的硬 體設定變更。 2. 鬆開電腦主機的機殼蓋並將之取下(如果您的主機板已經放置在主機內)。 3. 找到一個您想要插入新擴充卡的空置插槽,並以十字螺絲起子鬆開該插槽位於主 機背板的金屬擋板的螺絲,最後將金屬擋板移出。 4. 將擴充卡上的金手指對齊主機板上的擴充槽,接著慢慢地插入槽中,並以目視的 方法確認擴充卡上的金手指已完全沒入擴充槽中。 5. 再用剛才鬆開的螺絲將擴充卡固定在機殼內。 6. 將電腦主機的機殼蓋裝回鎖好。 1.5.
1.5.3 PCI Express 2.0 x1 介面卡擴充插槽 本主機板支援 PCI Express 2.0 x1 網路卡、SCSI 卡與其他與 PCI Express 規格相 容的卡。 1.5.4 PCI Express 3.0/2.0 x16 介面卡擴充插槽 本主機板配備 2 個 PCI Express x16 插槽,可支援 PCI Express x16 規格的顯示卡 以及其他符合 PCI Express 規格的功能擴充卡。 本主機板指定中斷要求 A B C D E F G H – – 共享 – – – – – PCIE x16 共享 – – – – – – – PCIE x1_1 共享 – – – – – – – PCIE x1_2 – 共享 – – – – – – Intel PCH SATA 控制器 – – – 共享 – – – – HD Audio – – – – – – 共享 – USB2.0_1 – – – – – – – 共享 USB2.
除了清除 CMOS 組態資料之外,請勿將主機板上 CLRTC 的跳線帽由預設 值的位置移除,因為這麼做可能會導致系統開機失敗。 • 如果上述方法無效,請將內建電池移除,再將跳線帽移除一次來清除 CMOS 組態資料。清除完成後,請將電池重新裝回主機板。 •如果您是因為超頻的緣故導致系統無法正常開機,您無須使用上述的組 態資料清除方式來排除問題。建議可以採用 C.P.R(CPU 自動參數回復) 功能,只要將系統重新開啟 BIOS 即可自動回復預設值。 2. 鍵盤和 USB 裝置喚醒跳線(KB_USBPWB) 此跳線允許您開啟或關閉 PS/2 裝置的喚醒功能。若您將跳線帽設定為 [23](+5VSB)短路,可透過按下 PS/2 鍵盤上的按鍵或點擊 PS/2 滑鼠喚醒電腦。 要使用此功能,ATX 電源需提供至少 1A 的電流與 +5VSB 電壓,並在 BIOS 中進 行相應設定。 1 2 2 3 KB_USBPWB B85M-G +5V +5VSB (Default) B85M-G Keyboard and USB device wake up 3.
1.7 元件與周邊裝置的連接 1.7.1 後側面板連接埠 1 2 12 11 3 10 9 8 4 5 6 7 1. PS/2 滑鼠連接埠(綠色):將 PS/2 滑鼠插頭連接到此連接埠。 2. VGA 連接埠:這組 15-pin 連接埠可連接 VGA 顯示屏幕或其他 VGA 硬體裝置。 3. RJ-45 網路連接埠:該連接埠可經 Gigabit 網路線連接至 LAN 網路。請參考下表 中各燈的說明。 網路指示燈說明 Activity/Link 指示燈 ACT/LINK 指示燈 速度指示燈 狀態 描述 狀態 描述 關閉 沒有連接 關閉 連接速度 10Mbps 橘色 已連接 橘色 連接速度 100Mbps 橘色(閃爍) 資料傳送中 綠色 連接速度 1Gbps 橘色(閃爍后 準備從 S5 模式 持續亮著) 啟動喚醒功能 4. 音效輸入連接埠(淺藍色):您可以將磁帶、CD、DVD 連接到此音效輸入連接埠。 速度 指示燈 網路連接埠 播放器等的音效輸出端 5.
二、四、六或八聲道音效設定 接頭 耳機/二聲道 喇叭輸出 四聲道 喇叭輸出 六聲道 喇叭輸出 八聲道 喇叭輸出 淺藍色(後面板) 聲音輸入端 後置喇叭輸出 後置喇叭輸出 後置喇叭輸出 草綠色(後面板) 聲音輸出端 前置喇叭輸出 前置喇叭輸出 前置喇叭輸出 粉紅色(後面板) 麥克風輸入端 麥克風輸入端 中央/重低音喇叭輸出 中央/重低音喇叭 輸出 草綠色(前面板) – – – 側邊環繞喇叭輸 出 要設定八聲道音效,請使用前面板具有 HD 音效插孔的機殼,以支援八 聲道音效輸出。 7. USB 2.0 裝置連接埠 3 和 4:這二組 4-pin 通用序列匯流排(USB)連接埠可連接 到使用 USB 2.0/1.1 介面的硬體裝置。 8. HDMI 連接埠:此高清晰多媒體連接埠(High-Definition Multimedia Interface), 兼容 HDCP,可播放 HD DVD、Blu-Ray 與其他保護內容。 9. USB 3.0 裝置連接埠 5 和 6:這二組 9-pin 通用序列匯流排(USB)連接埠可連接 到使用 USB 3.
1.7.2 內部連接埠 1. ATX 主機板電源插槽(24-pin EATXPWR、4-pin ATX12V) 這些電源插槽用來連接到一個 ATX 電源供應器。電源供應器所提供的連接插 頭已經過特別設計,只能以一個特定方向插入主機板上的電源插槽。找到正確的 插入方向後,僅需穩穩地將之套進插槽中即可。 GND GND +12V DC +12V DC ATX12V B85M-G EATXPWR +3 Volts +12 Volts +12 Volts +5V Standby Power OK PIN 1 GND +5 Volts GND +5 Volts GND +3 Volts +3 Volts GND +5 Volts +5 Volts +5 Volts -5 Volts GND GND GND PSON# GND -12 Volts +3 Volts PIN 1 B85M-G ATX power connectors • 建議您使用符合 ATX 12 V 2.
3.
5. 中央處理器 / 機殼風扇電源插槽(4-pin CPU_FAN、4-pin CHA_FAN) 將風扇電源接頭連接到這三組風扇電源插槽,確定每一條黑線與這些插槽的 接地端(GND)相匹配。 CPU FAN PWM CPU FAN IN CPU FAN PWR GND CPU_FAN B85M-G CHA FAN PWM CHA FAN IN CHA FAN PWR GND CHA_FAN B85M-G Fan connectors 千萬要記得連接風扇的電源,若系統中缺乏足夠的風量來散熱,很容易 因為主機內部溫度逐漸升高而導致當機,甚至更嚴重者會燒毀主機板上 的電子元件。注意:這些插槽並不是單純的排針,不要將跳線帽套在它 們的針腳上! 6.
7. Intel® B85 Serial ATA 3.0Gb/s 裝置連接插座 (7-pin SATA3G_1~2 [咖啡色]) 這些插槽支援使用 Serial ATA 3.0Gb/s 排線連接 Serial ATA 3.0Gb/s 硬碟或光 碟機。 SATA3G_2 GND RSATA_RXP2 RSATA_RXN2 GND RSATA_TXN2 RSATA_TXP2 GND B85M-G GND RSATA_RXP1 RSATA_RXN1 GND RSATA_TXN1 RSATA_TXP1 GND SATA3G_1 B85M-G Intel® SATA 3.0Gb/s connectors 當您使用支援 NCQ 技術的硬碟時,請將 BIOS 程式中的 SATA Mode Selection 設定為 [AHCI Mode]。請參考「2.6.3 SATA 裝置設定(SATA Configuration)」一節的說明。 8. Intel® B85 Serial ATA 6.0Gb/s 裝置連接插座 (7-pin SATA6G_1~4 [黃色]) 這些插槽支援使用 Serial ATA 6.
9. USB 3.0 擴充套件排線插座(20-1 pin USB3_12) 這個插槽用來連接額外的 USB 3.0 連接埠模組,並與 USB 2.0 規格相容。若 是您的機殼提供有 USB 3.0 前面板連接排線,將該排線連接至本插槽,就可擁有 前面板 USB 3.0 解決方案,支援傳送速率最高達 5Gbps,可對 USB 充電裝置進行 快速充電並優化能效。 USB3_12 B85M-G GND IntA_P1_D+ IntA_P1_DGND IntA_P1_SSTX+ GND IntA_P1_SSTXIntA_P1_SSRX+ IntA_P1_SSRXUSB3+5V IntA_P2_D+ IntA_P2_DGND IntA_P2_SSTX+ IntA_P2_SSTXGND IntA_P2_SSRX+ IntA_P2_SSRXUSB3+5V PIN 1 B85M-G USB3.0 Front panel connector USB 3.0 模組需另行購買。 10. USB 2.
11.
13. 機殼開啟警告排針 (4-1 pin CHASSIS) 這組排針提供給設計有機殼開啟偵測功能的電腦主機機殼之用。此外,尚須 搭配一個外接式偵測裝置譬如機殼開啟偵測感應器或者微型開關。在本功能啟用 時,若您有任何移動機殼元件的動作,感應器會隨即偵測到並且送出一信號到這 組接針,最後會由系統記錄下來這次的機殼開啟事件。本項目的預設值是將跳線 帽套在 CHASSIS 排針中標示著“Chassis Signal”和“GND”的二個針腳上,若 您想要使用本功能,請將跳線帽從“Chassis Signal”和“GND”的針腳上移除。 B85M-G Chassis Signal GND +5VSB_MB CHASSIS B85M-G Chassis intrusion connector 1.8 內建指示燈 1.
1.9 軟體支援 1.9.1 安裝作業系統 本主機板完全適用於 Windows® 7(32bit/64bit)與 Windows® 8(32bit/64bit)作 業系統。使用最新版本的作業系統並且不定時地升級,是讓硬體配備得到最佳工作效 率的有效方法。 由於主機板與周邊硬體裝置的選項設定繁多,本章僅就軟體的安裝程式供您 參考。您也可以參閱您使用的作業系統說明檔案以取得更詳盡的資訊。 1.9.2 驅動程式與公用程式光碟資訊 隨貨附贈的驅動程式與公用程式光碟包括了數個有用的軟體與公用程式,將它們 安裝到系統中可以強化主機板的機能。 驅動程式與公用程式光碟的內容若有更新,恕不另行通知。請造訪華碩網 站(http://tw.asus.
1-22 第一章:產品介紹
2 BIOS 資訊 2.1 管理、更新您的 BIOS 程式 建議您先將主機板原始的 BIOS 程式備份到一片 USB 隨身碟中,以備您 往後需要再度安裝原始的 BIOS 程式。使用華碩線上更新程式來拷貝主機 板原始的 BIOS 程式。 2.1.
2.1.2 使用華碩 EZ Flash 2 更新 BIOS 程式 華碩 EZ Flash 2 程式讓您能輕鬆的更新 BIOS 程式,可以不必再到作業系統模式 下執行。 在使用此程式前,請從華碩網站上(http://tw.asus.com)下載最新的 BIOS 檔案。 請依據以下步驟使用 EZ Flash 2 更新 BIOS: 1. 將儲存有最新 BIOS 檔案的 USB 隨身碟插入 USB 連接埠。 2. 進入 BIOS 設定程式的進階模式(Advanced Mode)畫面,來到 Tool 選單並選擇 EZ Flash2 並按下 <Enter> 鍵將其開啟。 3. 按下 <Tab> 鍵切換到 Driver 區域。 4. 按上/下方向鍵找到儲存有最新 BIOS 檔案的 USB 隨身碟,接著按下 <Enter> 鍵。 5. 按下 <Tab> 鍵切換到 Folder Info 區域。 6.
2.1.3 使用 CrashFree BIOS 程式回復 BIOS 程式 華碩最新自行研發的 CrashFree BIOS 工具程式,讓您在當 BIOS 程式與資料被病 毒入侵或損毀時,可以輕鬆地從驅動程式與公用程式光碟中,或是從含有最新或原始 BIOS 檔案的 USB 隨身碟中回復 BIOS 程式的資料。 • 使用此程式前,請將行動儲存裝置中的 BIOS 檔案重新命名為: B85MG.CAP。 • 從驅動程式與公用程式光碟中的 BIOS 可能不是最新版本,請造訪華碩 網站(http://tw.asus.com)來下載最新的 BIOS 程式。 回復 BIOS 程式: 請依照下列步驟回復 BIOS 程式: 1. 啟動系統。 2. 將儲存有 BIOS 檔案的驅動程式與公用程式光碟放入光碟機,或 USB 隨身碟插 入 USB 連接埠。 3. 接著工具程式便會自動檢查裝置中是否存有 BIOS 檔案。當搜索到 BIOS 檔案後, 工具程式會開始讀取 BIOS 檔案並自動進入 EZ Flash 2 應用程式。 4.
在 DOS 環境中啟動系統 1. 將儲存有最新的 BIOS 檔案與 BIOS Updater 工具程式的 USB 隨身碟連接到電腦 的 USB 連接埠。 2. 啟動電腦。當 ASUS 圖示出現時,按下 <F8> 以顯示「BIOS Boot Device Select」 選單。將驅動程式與公用程式光碟放入光碟機,並選擇光碟機為啟動裝置。 3. 當「Make Disk」選單出現時,按下對應的數字鍵選擇 FreeDOS command prompt 項。 4. 在 FreeDOS 提示符後輸入 d: 並按下 <Enter>,從 Drive C(光碟機)切換為 Drive D(USB 隨身碟)。 Welcome to FreeDOS (http://www.freedos.org)! C:\>d: D:\> 更新 BIOS 檔案 請依照以下步驟用 BIOS Updater 工具程式更新 BIOS 檔案: 1. 在 FreeDOS 提示符後輸入 bupdater /pc /g 並按下 <Enter>。 D:\>bupdater /pc /g 2.
3. 按下 <Tab> 鍵在各設定欄之間切換,接著用 <Up/Down/Home/End> 鍵來選 擇 BIOS 檔案並按下 <Enter>。BIOS Updater 會檢查您所選擇的 BIOS 檔案並 提示您確認是否要更新 BIOS。 Are you sure to update BIOS? Yes No 4. 選擇 Yes 並按下 <Enter>。當 BIOS 更新完畢後,按 <ESC> 離開 BIOS Updater。重新啟動您的電腦。 當更新 BIOS 時,請勿關閉或重置系統!若是這麼做,將可能導致系統開 機失敗。 • 對於 BIOS Updater 1.30 或更高版本,當 BIOS 更新完畢後,工具程式會 自動回到 DOS 畫面。 • BIOS 程式的出廠預設值可讓系統運作處於最佳效能。若系統因您改變 BIOS 程式而導致不穩定,請讀取出廠預設值來保持系統的穩定。請在 「Exit」 選單中選擇 Load Optimized Defaults 項目。詳細說明請參考 「2.
2.2 BIOS 程式設定 BIOS 設定程式用於更新或設定 BIOS。BIOS 設定畫面中標示了操作功能鍵與簡明 的操作說明,幫助您進行系統設定。 在開機時進入 BIOS 設定,您可以依據以下步驟進行: • 在系統自我測試(POST)過程中按下 <Delete> 鍵。若不按下 <Delete> 鍵,自我測試會繼續進行。 在 POST 過程結束後再進入 BIOS 設定,您可以選擇以下任一步驟進行: • 按下 <Ctrl> + <Alt> + <Del> 鍵。 • 按下機殼上的 <RESET> 鍵重新開機。 • 您也可以將電腦關閉然後再重新開機。請在嘗試了以上兩種方法失敗後再選擇 這一操作。 透過電源鍵、Reset 鍵或 <Ctrl> + <Alt> + <Del> 鍵強迫正在運作 的系統重新開機會毀損到您的資料或系統,我們建議您正確地關閉正在 運作的系統。 • 本章節的 BIOS 程式畫面僅供參考,將可能與您所見到的畫面有所差 異。 • 請至華碩網站(http://tw.asus.
EZ 模式(EZ Mode) 預設情況下,當您進入 BIOS 設定程式後,EZ 模式(EZ Mode)畫面就會出現。 EZ 模式(EZ Mode)顯示基本系統資訊概要,並用來選擇顯示語言、系統效能模式 與啟動裝置順序。要進入進階模式(Advanced Mode),點選 Exit/Advanced Mode 按 鈕,接著選擇進階模式(Advanced Mode)。 進入 BIOS 設定程式的預設畫面可變更。請參考「2.8 啟動選單(Boot)」 部份 Setup Mode 項目的說明。 顯示 CPU / 主機板的溫度,CPU / 5V / 3.
返回按鈕 選單項目 子選單項目 功能表列 設定值 設定視窗 線上操作說明 卷軸 操作功能鍵 上次修正設定 快速筆記 功能表列 BIOS 設定程式最上方各選單功能說明如下: My Favorites Main 本項目用於保存經常使用的系統設定和配置資訊。 Ai Tweaker 本項目用於變更超頻設定 Advanced 本項目提供系統進階功能設定 Monitor 本項目顯示系統溫度、電源狀態,並變更風扇設定 Boot 本項目提供系統開啟設定 Tool Exit 本項目提供特殊功能設定 本項目提供系統基本設定 本項目提供離開 BIOS 設定程式與出廠預設值還原功能 選單項目 在功能表列選定選項時,被選擇的功能將會反白,並在選單項目區域內出現相應 的項目。 點選功能表列中的其他項目(例如:Ai Tweaker、Advanced、Monitor、Boot、 Tool 與 Exit) 會出現該項目不同的選項。 返回按鈕 當進入子選單時,此按鈕會出現。按下 <Esc> 或使用 USB 滑鼠點選此按鈕回到 前一個選單畫面。 子選單項目 在任何選單畫面中的項目前若有一個大於號(
設定視窗 在選單中選擇功能項目,接著按下 <Enter> 鍵,程式將會顯示包含此功能所提供 的選項小視窗,您可以利用此視窗來設定您所想要的設定。 捲軸 在選單畫面的右方若出現捲軸,即代表此頁選項超過可顯示的畫面,您可利用上/ 下方向鍵或是 PageUp/PageDown 鍵來切換畫面。 操作功能鍵 在選單畫面的右下方為操作功能鍵說明,請參照功能鍵說明來選擇及改變各項功 能。 線上操作說明 在選單畫面的右上方為目前所選擇的作用選項的功能說明,此說明會依選項的不 同而自動變更。 設定值 此區域顯示選單項目的設定值。這些項目中,有的功能選項僅為告知使用者目前 執行狀態,並無法更改,此類項目就會以淡灰色顯示。而可更改的項目,當您使用方 向鍵移動項目時,被選擇的項目以反白顯示。 設定值被選擇後以反白顯示。要改變設定值請選擇此項目,並按下 <Enter> 鍵以 顯示設定值列表。 快速筆記 此區域可進入您在 BIOS 中所做的內容筆記。 上次修改設定按鈕 此按鈕可顯示您在 BIOS 設定中上一次所做的修改項目。 2.
在 My Favorites 中新增項目 依據以下步驟將經常使用的 BIOS 項目新增至我的最愛: 1. 使用方向鍵選擇您要新增的項目。若使用滑鼠,將指針懸停在項目上。 2. 在鍵盤上按下 ,或按下滑鼠右鍵新增項目至我的最愛頁面。 2.4 主選單(Main) 當您進入 BIOS 設定程式的進階模式(Advanced Mode)時,首先出現的第一個畫 面即為主選單。主選單顯示系統資訊概要,用來設定系統日期、時間、語言與安全設 定。 2.4.1 System Language [English] 用來選擇 BIOS 語言。 設定值有:[English] [Русский] [한국어] [Español] 2.4.2 System Date [Day xx/xx/xxxx] 設定您的系統日期(通常是目前的日期)。 2.4.3 System Time [xx:xx:xx] 設定系統的時間(通常是目前的時間)。 2.4.
管理者密碼(Administrator Password) 若您已經設定了一個管理者密碼,建議您輸入管理者密碼來進入系統。否則,您 只能看到或變更 BIOS 設定程式中的部份內容。 請依照以下步驟設定系統管理者密碼: 1. 選擇 Administrator Password 項目並按下 <Enter>。 2. 在「Create New <Enter>。 Password」視窗出現時,輸入欲設定的密碼,輸入完成按下 3. 在彈出的確認視窗中再一次輸入密碼以確認密碼正確。 請依照以下步驟變更系統管理者密碼: 1. 選擇 Administrator Password 項目並按下 <Enter>。 2. 在「Enter Current <Enter>。 Password」視窗出現時,輸入現在的密碼,輸入完成按下 3. 在「Create New Password」視窗出現時,輸入欲設定的新密碼,輸入完成按下 <Enter>。 4.
2.
向下捲動頁面可顯示顯示以下項目: Target CPU Turbo-Mode Speed : xxxxMHz 顯示目標 CPU Turbo-Mode 速度。 Target DRAM Speed : xxxxMHz 顯示目標 DRAM 速度。 Target Cache Speed : xxxxMHz 顯示目標快取速度。 Target DMI/PEG Clock : xxxxMHz 顯示目標 DMI/PEG 時脈。 Target iGPU Speed : xxxxMHz 顯示目標 iGPU 速度。 2.5.1 Ai Overclock Tuner [Auto] 本項目可以讓您設定 CPU 的超頻選項來達到您所想要的 CPU 內頻。請選擇以下 任一種預設的超頻選項: [Auto] 自動載入系統最佳化設定值。 [X.M.P.] 可讓您的系統自動優化 CPU 倍頻,BCLK 頻率和記憶體參數。若您 安裝支援 eXtreme Memory Profile (X.M.P.) 技術的記憶體模組,請選 擇此項目以使用記憶體模組支援的設定檔,優化系統性能。 2.5.
只有當 CPU Core Ratio 項目設為 [Per Core] 或 [Per Core] 時以下項目才 會出現。 1-Core Ratio Limit [Auto] 本項目用來設定 1-Core 倍頻限制。選擇 [Auto] 套用 CPU 預設 Turbo 倍頻設 定,或手動指定 1-Core 倍頻限制值,可高於或等於 2-Core 倍頻限制。 2-/3-/4-Core Ratio Limit [Auto] 只有當 CPU Core Ratio 項目設為 [Per Core] 時,這些項目才可以被設定。 2.5.4 Min CPU Cache Ratio [Auto] 本項目用來將處理器非核心倍頻設定至可能的最小值。設定值有:[Auto] [1] - [30] 2.5.5 Max CPU Cache Ratio [Auto] 本項目用來將處理器非核心倍頻設定至可能的最大值。設定值有:[Auto] [1] - [30] 2.5.
自行變更數值將會導致系統的不穩定與硬體毀損,當系統出現不穩定的 狀況時,建議您使用預設值。 Primary Timings DRAM CAS# Latency [Auto] 設定值有:[Auto] [1 DRAM Clock] – [31 DRAM Clock] DRAM RAS# to CAS# Delay [Auto] 設定值有:[Auto] [1 DRAM Clock] – [31 DRAM Clock] DRAM RAS# PRE Time [Auto] 設定值有: [Auto] [1 DRAM Clock] – [31 DRAM Clock] DRAM RAS# ACT Time [Auto] 設定值有: [Auto] [1 DRAM Clock] – [63 DRAM Clock] DRAM COMMAND Rate [Auto] 設定值有:[Auto] [1 DRAM Clock] [2 DRAM Clock] [3 DRAM Clock] Secondary Timings DRAM RAS# to RAS# Delay [Auto] 設定值有:[Auto] [1 DRAM Clo
設定值有:[Auto] [1 DRAM Clock] - [63 DRAM Clock] DRAM RTL (CHB) [Auto] 設定值有:[Auto] [1 DRAM Clock] - [63 DRAM Clock] DRAM IO-L (CHA) [Auto] 設定值有:[Auto] [Delay 1 Clock] - [Delay 15 Clock] DRAM IO-L (CHB) [Auto] 設定值有:[Auto] [Delay 1 Clock] - [Delay 15 Clock] Third Timings tRDRD [Auto] 設定值有:[Auto] [1 DRAM Clock] – [7 DRAM Clock] tRDRD_dr [Auto] 設定值有:[Auto] [1 DRAM Clock] – [15 DRAM Clock] tRDRD_dd [Auto] 設定值有:[Auto] [1 DRAM Clock] – [15 DRAM Clock] tWRRD [Auto] 設定值有:[Auto] [1 DRAM Clock] – [63 DRAM Clock] tWRR
[Disable] 關閉 MRC 快速啟動。 DRAM CLK Period [Auto] 設定值有:[Auto] [1] – [14] Channel A DIMM Control [Enable Bot...] 設定值有:[Enable Both DIMMS] [Disable DIMM0] [Disable DIMM1] [Disable Both DIMMS] Channel B DIMM Control [Enable Bot...] 設定值有:[Enable Both DIMMS] [Disable DIMM0] [Disable DIMM1] [Disable Both DIMMS] Scrambler Setting [Optimized ...] 設定值有:[Optimized (ASUS)] [Default (MRC)] 2.5.
Manual Adjustment [Fast] 本項目用來設定 CPU 電源相位控制回應。設定值有:[Ultra Fast] [Fast] [Medium] [Regular] CPU Power Duty Control [T.Probe] 此項目用來調整每個元件相位的電流與散熱。 [T. Probe] 此設定值 VRM 保持熱量平衡。 [Extreme] 此設定值保持目前 VRM 平衡。 CPU Current Capability [Auto] 此項目用來設定全部電能範圍,並同步擴大超頻頻率範圍。設定值有:[Auto] [100%] [110%] [120%] [130%] [140%] 超頻或處理器高負載情況下,請選擇較高的設定值以獲得額外的電能支援。 2.5.
CPU Internal Power Switching Frequency Frequency Tuning Mode [Auto] 本項目用來提高或降低內部調節器的切換頻率。降低頻率可幫助節能,提 高頻率或獲得電壓穩定性,設定值有:[Auto] [+] [-] CPU Internal Power Fault Control Thermal Feedback [Auto] 允許當外部調節器的溫度超過限制時,系統為 CPU 採取預警動作。設定 值有:[Auto] [Disabled] [Enabled] CPU Integrated VR Fault Management [Auto] 關閉此項目防止超頻時全整合電壓調節器中斷。設定值有:[Auto] [Disabled] [Enabled]CPU Internal Power Configuration CPU Integrated VR Efficiency Management [Auto] 當處理器處於低電源狀態時提升節能效能。關閉此項目可時全集成電壓調 節器總是以高效能運作。設定值有:[Auto] [High Performance] [Balan
2.5.14 Extreme OV [Disabled] 此項目預設設定為 [Disabled],為 CPU 提供過壓保護。若將此項目設為 [Enabled], 您可以為選擇超頻電壓,但可能降低 CPU 壽命。 2.5.15 CPU Core Voltage [Auto] 本項目用來設定處理器核心的電壓饋電數量。核心頻率提高時提高電壓數量。設 定值有:[Auto] [Manual Mode] [Offset Mode] [Adaptive Mode] 僅適用於一些特殊規格的中央處理器。 CPU Core Voltage Override [Auto] 本項目用來設定 CPU 核心電壓覆寫。使用 <+> / <-> 鍵調整設定值。設定值範圍從 0.001V 至 1.920V,以 0.
2.5.17 CPU Graphics Voltage [Auto] 本項目用來設定處理器內建顯示單元的電壓饋電數量。iGPU 頻率提高時提高電壓 數量。設定值有:[Auto] [Manual Mode] [Offset Mode] [Adaptive Mode] [Adaptive Mode] 僅適用於一些特殊規格的中央處理器。 CPU Graphics Voltage Override [Auto] 本項目用來設定 CPU 顯示電壓覆寫。使用 <+> / <-> 鍵調整設定值。設定值範圍從 0.001V 至 1.920V,以 0.
2.5.20 CPU Digital I/O Voltage Offset Mode Sign [+] 本項目用來設定處理器 I/O 連接埠的數字部份的電壓饋電數量。設定值:[+] [-] CPU Digital I/O Voltage Offset [Auto] 本項目用來設定處理器 I/O 連接埠的數位部份的電壓饋電數量。記憶體頻率提高時 提高電壓數量。設定值範圍從 0.001V 至 0.999V,以 0.001V 為增量調整。 2.5.21 SVID Support [Auto] 關閉 SVID 支援可使 [Disabled] [Enabled] CPU 停止與外部電壓調節器通訊。 設定值有:[Auto] 2.5.22 CPU Input Voltage (VCCIN) [Auto] 本項目用來設定 CPU 輸入電壓。設定值範圍從 0.800V 至 2.700V,以 0.010V 為 增量調整。 2.5.23 DRAM Voltage [Auto] 本項目用來設定記憶體電壓。設定值範圍從 1.200V 至 1.800V,可調整範圍從 1.350V 至1.800V,以 0.
2.5.26 DRAM CTRL REF Voltage [Auto] 本項目用來設定記憶體電壓片段作為控制線參考。使用 <+> / <-> 鍵調整設定值。 設定值範圍從 0.3950V 至 0.6300V,以 0.0050V 為增量調整。 2.5.27 DRAM DATA REF Voltage on CHA [Auto] 本項目用來設定通道 A 上的記憶體資料參考電壓。設定值範圍從 0.3950V 到 0.6300V,以 0.0050V 為增量調整。不同的設定可能可提高記憶體超頻能力。 2.5.28 DRAM DATA REF Voltage on CHB [Auto] 本項目用來設定通道 B 上的記憶體資料參考電壓。設定值範圍從 0.3950V 到 0.6300V,以 0.0050V 為增量調整。不同的設定可能可提高記憶體超頻能力。 2.5.29 CPU Spread Spectrum [Auto] [Auto] [Disabled] [Enabled] 2.
2.6.
EIST(Enhanced Intel SpeedStep Technology)[Enabled] 本項目可讓您開啟或關閉 Enhanced Intel® SpeedStep Technology(EIST)技術。 [Disabled] CPU 在預設速度下運作。 [Enabled] 由作業系統控制 CPU 速度。 Turbo Mode [Enabled] 本項目在特定情況下,允許處理器以比標準頻率更快的速度運作。設定值 有:[Enabled] [Disabled] 僅指定型號的 CPU 支援 Turbo Mode。 CPU C States [Auto] [Auto] 自動配置。 [Enabled] 開啟處理器 C 狀態功能。 [Disabled] 關閉處理器 C 狀態功能。 只有當 CPU C States 項目設為 [Enabled] 時此以下項目才會出現。 Enhanced C1 state [Enabled] [Enabled] 開啟增強 C1 狀態。 [Disabled] 關閉增強 C1 狀態。 CPU C3 Report [Enabled] 本項目用來開啟或關
2.6.
2.6.
[96M] [128M] [160M] [192M] [224M] [256M] [288M][320M] [352M] [384M] [416M] [448M] [480M] [512M] [1024M] Render Standby [Auto] 本項目可讓您透過內部繪圖裝置開啟或關閉 Render Standby 功能。設定項有: [Auto] [Disabled] [Enabled] iGPU Multi-Monitor [Disabled] 本項目用來開啟 iGPU 多顯示器支援功能。要支援 LucidLogix Virtu MVP 功能, 將此項目設為 [Enabled] 以加強內建與獨立顯示卡效能。iGPU 共享系統記憶體 固定為 64MB。設定值有:[Disabled] [Enabled] DMI Configuration 本項目用來控制不同的 DMI(Desktop Management Interface)功能。 DMI Gen 2 [Auto] 本項目用來開啟或關閉 DMI Gen 2。設定值有:[Auto] [Enabled] [Disabled] NB PCIe Confi
2.6.
只有當 HD Audio Controller 項目設為 [Enabled] 時以下二個項目才會出 現。 Front Panel Type [HD] 依據前面板音效模組支援的音效標準,設定前面板音效連接埠(AAFP)模式為 legacy AC’97 或高傳真音效。 [HD] 將前面板音效連接埠(AAFP)模式設定為高傳真音效。 [AC97] 將前面板音效連接埠(AAFP)模式設定為 legacy AC’97。 SPDIF Out Type [SPDIF] [SPDIF] [HDMI] 設為 [SPDIF] 開啟 SPDIF 音效輸出。 設為 [HDMI] 開啟 HDMI 音效輸出。 Realtek LAN Controller [Enabled] [Enabled] [Disabled] 開啟 Realtek® 網路控制器。 關閉 Realtek® 網路控制器。 Realtek PXE OPROM [Disabled] 本項目用來開啟或關閉 [Enabled] [Disabled] Realtek 網路控制器的 PXE OptionRom,設定值有: 序列埠設定(Serial
Change Settings [Auto] 本項目可選擇 Super I/O 裝置的最佳設定。設定值有:[Auto] [IO=378h; IRQ=5;] [IO=378h; IRQ=5,6,7,9,10,11,12;] [IO=278h; IRQ=5,6,7,9,10,11,12;] [IO=3BCh; IRQ=5,6,7,9,10,11,12;] Device Mode [STD Printe...] 本項目可選擇 Printer Port 模式。 設定值有:[STD Printer Mode] [SPP Mode] [EPP-1.9 and SPP Mode] [EPP-1.7 and SPP Mode] [ECP Mode] [ECP and EPP 1.9 Mode] [ECP and EPP 1.7 Mode] 2.6.
只有當 Network Stack 項目設為 [Enabled] 時以下項目才會出現。 Ipv4 PXE Support [Enabled] 本項目用來開啟或關閉 Ipv4 PXE 啟動項支持。設定值:[Disabled] [Enabled] Ipv6 PXE Support [Enabled] 本項目用來開啟或關閉 Ipv6 PXE 啟動項支持。設定值:[Disabled] [Enabled] 2.
2.7.1 CPU Temperature [xxx℃/xxx℉] 本主機板具備了中央處理器的溫度感測器,可自動偵測並顯示目前處理器的溫度。 若您不想顯示偵測到的溫度,請選擇 [Ignore]。 2.7.2 CPU / Chassis Fan Speed [xxxx RPM] 或 [Ignore] / [N/A] 主機板具備中央處理器 / 機殼風扇轉速 RPM(Rotations Per Minute)監控功能。 如果主機板上沒有連接風扇,這裡會顯示 [N/A]。若您不想顯示偵測到的速度,請選擇 [Ignore]。 2.7.3 CPU Input Voltage (VCCIN), 3.3V Voltage, 5V Voltage, 12V Voltage 本主機板具有電壓監控的功能,用來確保主機板以及 CPU 接受正確的電壓準位,以 及穩定的電流供應。若您不想偵測此項目,請選擇 [Ignore]。 2.7.
CPU Fan Min. Duty Cycle(%) [20] 使用 <+> / <-> 鍵調整 CPU 風扇最小轉速。設定值範圍從 20% 到 100%。 當 CPU 溫度低於下限 時,CPU 風扇會以最小的轉速運作。 2.7.
2.8 啟動選單(Boot) 本選單可讓您改變系統啟動裝置與相關功能。 往下捲動顯示以下項目: 2.8.1 Fast Boot [Enabled] [Disabled] [Enabled] 系統返回正常開機速度。 系統加速啟動。 只有當 Fast Boot 項目設為 [Enabled] 時以下項目才會出現。 SATA Support [ALL Devices] 在開機自我測試(POST)時,所有連接 SATA 連接埠的裝 置都可用,這一過程將會延長 POST 時間 。 [Hard Drive Only] 在開機自我測試(POST)時,只有連接 SATA 連接埠的硬 碟驅動可用,任何硬體修改項都將關閉快速啟動功能。 [Boot Drive Only] 在開機自我測試(POST)時,只有連接 SATA 連接埠的啟 動驅動可用,任何硬體修改項都將關閉快速啟動功能。 USB Support [Partial In...
[Partial Initialization] 為了得到更快速的 POST 時間,只有連接了鍵盤和滑鼠的 USB 連接埠可被偵測到。 PS/2 Keyboard and Mouse Support [Auto] 安裝了鍵盤與滑鼠後請選擇以下任一設定值。只有當快速啟動功能開啟時,這些 設定才有用。 [Auto] 當 PS/2 裝置未重新連接或變更時,為獲得更快的 BIOS POST 時間,PS/2 裝置在系統啟動或重新開啟時可用。若您在重新開 啟系統前移除或變更了 PS/2 裝置,PS/2 裝置將不可用,且無 法透過 PS/2 裝置控制 BIOS 設定程式。 [Full Initialization] 為獲得完整的系統控制,在 POST 過程中 PS/2 裝置可用。此將 延長 POST 時間。 [Disabled] 為儘量縮短 POST 時間,所有的 PS/2 裝置將在系統進入作業系 統後才可用。 Network Stack Driver Support [Disabled] [Disabled] [Enabled] BIOS 跳過網路堆棧驅動並嘗試從下一個裝置啟動。 允許 BIO
2.8.4 Wait For‘F1’If Error [Enabled] 當您將本項目設為 [Enabled],那麼系統在開機過程出現錯誤訊息時,將會等待您 按下 <F1> 鍵確認才會繼續進行開機程式。設定值有:[Disabled] [Enabled] 2.8.5 Option ROM Messages [Force BIOS] [Force BIOS] 在啟動過程中,第三方 ROM 資訊將會強制顯示。 [Keep Current] 只有當第三方廠商將裝置設定為顯示 ROM 資訊時,第三方 ROM 資訊 才會顯示。 2.8.6 Interrupt 19 Capture [Disabled] [Enabled] [Disabled] 允許附加 ROM 捕捉中斷 19。 關閉此功能。 2.8.7 Setup Mode [EZ Mode] [Advanced Mode] 將進階模式(Advanced Mode)畫面設為進入 BIOS 設定程式的預設畫 面。 [EZ Mode] 將 EZ 模式(EZ Mode)畫面設為進入 BIOS 設定程式的預設畫面。 2.8.
2.8.9 Secure Boot 本項目用來設定安全啟動相關的參數。 OS Type [Windows UE...
Delete the KEK 本項目用來從系統刪除 KEK。設定值有:[Yes] [No] Load KEK from File 本項目用來載入從 USB 儲存裝置載入已下載的 KEK。 [Yes] 載入預設 KEK。 [Enabled] 從 USB 裝置載入。 Append KEK from file 本項目用來從儲存裝置載入額外的 KEK 用於附加 db 與 dbx 載入管理。 KEK 檔案必須格式化為一個基於時間認證變量的 UEFI 變量結構。 DB Management db(認證簽名資料庫)列出了您可以在單台電腦載入的 UEFI 公用程式、作業系 統載入器與 UEFI 驅動程式的簽名者或鏡像檔案。 Delete the db 本項目用來從系統刪除 db。設定值有:[Yes] [No] Load db from File 本項目用來從 USB 儲存裝置載入已下載的 db。 Append db from file 本項目用來從儲存裝置載入一個額外的 db 以安全載入更多的鏡像檔案。 db 檔案必須格式化為一個基於時間認證變量的 UEFI 變量結構。 DBX Management dbx(
2.8.10 啟動項目順序(Boot Option Priorities) 這些項目讓您自行選擇開機磁碟並排列開機裝置順序。螢幕上顯示的裝置數量依 據系統中安裝的裝置而定。 • 若要以安全模式進入 Windows® 作業系統,請選擇以下任一操作: • 在 ASUS 的圖示出現時按下 <F5> • 在開機自我測試完成後,按下 <F8>。 2.8.
2.9 工具選單(Tools) 本工具選單可以讓您針對特別功能進行設定。請選擇選單中的選項並按下 <Enter> 鍵來顯示子選單。 2.9.1 ASUS EZ Flash 2 本項目用來執行 ASUS EZ Flash 2。按下 <Enter> 開啟 ASUS EZ Flash 2 畫面。 更多詳細資訊,請參考「2.1.2 使用華碩 EZ Flash 2 更新 BIOS 程式」部 份的說明。 2.9.2 ASUS O.C.
2.
華碩的連絡資訊 華碩電腦公司 ASUSTeK COMPUTER INC.(台灣) 市場訊息 技術支援 地址: 台灣臺北市北投區立德路 15 號 電話: +886-2-2894-3447 傳真: +886-2-2890-7798 電子郵件: info@asus.com.tw 全球資訊網:http://tw.asus.com 電話: 0800-093-456 線上支援: http://support.asus.com/techserv/ techserv.aspx 華碩電腦公司 ASUSTeK COMPUTER INC.(亞太地區) 市場訊息 技術支援 地址: 台灣臺北市北投區立德路 15 號 電話: +886-2-2894-3447 傳真: +886-2-2890-7798 電子郵件: info@asus.com.tw 全球資訊網:http://tw.asus.com 電話: +86-21-38429911 傳真: +86-21-58668722, ext. 9101# 線上支援: http://support.asus.com/techserv/ techserv.
(510)739-3777/(510)608-4555 800 Corporate Way, Fremont, CA 94539. Asus Computer International Signature : Date : Representative Person’s Name : Apr. 29, 2013 Steve Chang / President This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.