BE24ECSNK 系列 LCD 顯示器 使用手冊
初版 2022 年 2 月 版權所有 © 2022 ASUSTeK COMPUTER INC. 保留所有權利。 在未取得 ASUSTeK COMPUTER INC.
目錄 目錄 ......................................................................................................... iii 注意事項 ....................................................................................................... iv TCO 認證 ...................................................................................................... vi 安全資訊 ...................................................................................................... vii 保養和清潔 ...................................................
注意事項 聯邦通訊委員會聲明 本裝置符合 FCC 規定之第 15 篇。操作符合下列兩個條件: • 本裝置不會造成有害干擾,而且 • 本裝置會接受任何接收到的干擾,包括可能會影響裝置運作的干擾。 本設備通過測試並符合 FCC 規定之第 15 篇 B 級數位裝置的限制。這些限 制的用意在於提供適當防護,避免設備安裝在居住環境下產生有害干擾。 本設備會產生、使用和發射無線電頻能量,此外,若未依照指示安裝和使用, 可能會對無線電通訊產生不良干擾。然而,並不保證在特定安裝情況下不會 產生干擾。若本設備對收音機或電視機的收訊產生不良干擾(可開啟然後關 閉設備電源判定),使用者可透過以下方法消除干擾: • 重新調整接收天線的方向或位置。 • 增加設備和接收天線之間的距離。 • 將本設備連接到與接收器電源不同的電源插座上。 • 請向經銷商或有經驗的廣電技術人員尋求協助。 連接顯示器與顯示卡的遮蔽纜線,須符合 FCC 的規定。若未經相容性規定之相 關當局明示許可,擅自修改或改裝本裝置,使用者可能喪失操作本設備之權限。 符合 ENERGY STAR 標準的產品 ENERGY STAR 是美國環保署與美國能
注意事項:Energy Star 不支援 FreeDOS 與 Linux 作業系統。 加拿大通訊部聲明 本數位裝置未超過加拿大通訊部無線電干擾法規所規定之數位裝置無線電干 擾發射 的 B 級限制。 本設備為符合加拿大 ICES-003 規範的 B 級數位裝置。 This Class B digital apparatus meets all requirements of the Canadian Interference - Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouiller du Canada.
TCO 認證 A third-party certification according to ISO 14024 Toward sustainable IT products Say hello to a more sustainable product IT products are associated with a wide range of sustainability risks throughout their life cycle. Human rights violations are common in the factories. Harmful substances are used both in products and their manufacture. Products can often have a short lifespan because of poor ergonomics, low quality and when they are not able to be repaired or upgraded.
安全資訊 • 設定本顯示器之前,請詳讀產品包裝內的說明文件。 • 為預防起火或觸電,請勿將顯示器置於雨中或潮溼環境中。 • 請勿試圖打開顯示器的機殼。顯示器內部的高壓電可能造成人員嚴重受傷。 • 若電源供應器損壞,請勿嘗試自行修復。請洽詢合格的維修技術人員您的零 售商。 • 使用本產品前,請確定已正確連接所有纜線,而且電源線並未損壞。若發現任何 損壞,請立刻聯絡您的經銷商。 • 機殼背面或頂端的開口和通風口係用於散熱。請勿堵塞這些開口。除非通風 良好,否則請勿將本產品置於靠近散熱器或熱源的位置或其上方。 • 本顯示器只能在產品標籤所示的電源環境下操作。若您不確定您家中的電源 規格,請洽詢您的經銷商或當地的電力公司。 • 使用符合當地電源標準的電源插頭。 • 不可使排插和延長線的電源過載。電源過載會導致起火或人員觸電。 • 避免在多灰塵、潮溼和極端溫度的環境中使用。請勿將顯示器置於可能會使其受 潮的區域。請將顯示器置於平穩的表面上。 • 雷雨期間或長時間不使用時,請拔下本機的電源插頭。如此可預防顯示器因電源 突波而損壞。 • 請勿讓任何物體或液體進入顯示器機殼的開口
保養和清潔 • 抬高或重新移位顯示器之前,請先拔下纜線和電源線。顯示器移位前,請依照正 確的抬高方法。抬高或移動顯示器時,請握住顯示器的邊緣。請勿以拉抬底座或 纜線的方式抬高顯示器。 • 清潔。關閉顯示器的電源,然後拔下電源線。使用無毛球且不會刮傷螢幕的布清 潔顯示器表面。可用沾有中性清潔劑的布清除頑垢。 • 避免使用含有酒精或丙酮的清潔劑。使用顯示器專用的清潔劑。請勿直接將清潔 劑噴灑於螢幕上,否則可能滲入顯示器內並造成人員觸電。 若顯示器發生以下情況,屬於正常現象: • 不同的桌面模式可能導致螢幕有輕微亮度不均的情況。 • 顯示同一幅影像數小時後,切換影像時可能會出現前張影像的殘影。殘影會慢慢 消失,或者您可以開關電源數小時消除此情況。 • 螢幕變黑、閃爍或完全無法運作時,請洽詢您的經銷商或服務中心進行修復。 請勿自行修理螢幕! 本手冊使用的慣語 警告:執行作業時,避免人員受傷的資訊。 注意:執行作業時,避免零組件損壞的資訊。 重要:執行作業時「必須」遵守的資訊。 附註:協助執行作業的提示和其它資訊。 viii
其它詳細資訊來源 如需其它資訊和產品與軟體的更新程式,請參閱下列來源。 1. ASUS 網站 ASUS 全球網站提供有關 ASUS 硬體和軟體產品的最新資訊。請連至 http://www.asus.com 取得相關資訊。 2. 選用的說明文件 您的產品包裝內可能有經銷商所提供的選用說明文件。產品的標準包裝中不含 此類文件。 Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for our customers to be able to responsibly recycle our products, batteries and other components as well as the packaging materials. Please go to http://csr.asus.
x
1.1 歡迎使用! 感謝您購買 ASUS® LCD 顯示器! ASUS 最新的寬螢幕液晶顯示器提供更寬廣、更明亮和更清晰的顯示,以及許多可 增強觀看感受的功能。 您可藉由這些功能享受到本顯示器帶給您的便利與快樂的視覺體驗! 1.
1.3 顯示器介紹 1.3.1 正面圖 8 9 7 6 1. 5 4 3 2 1 電源按鈕/電源指示燈 • 開啟/關閉顯示器電源。 • 電源指示燈的顏色定義如下表所示。 2. 狀態 說明 白色 琥珀色 關閉 開機 待機模式 關閉 5 向按鈕: • OSD 選單關閉時顯示 OSD 選單。 • 執行選取的 OSD 選單項目。 • 3.
4. 連結按鈕: • 5. 接聽或結束語音/視訊通話。 麥克風靜音按鈕: • 6. 讓麥克風靜音或解除靜音。 音量按鈕: • 顯示音量列。 • 使用 5 向按鈕進行調整。 • 向下長按 5 秒,即可開啟或關閉按鍵鎖。 視訊會議軟體的按鈕功能可用性: 軟體 顯示器快速鍵 ZOOM - Microsoft Teams - 商務用 Skype Google Meet 7. 麥克風 8. 筆電鏡頭貼 9.
1.3.2 背面圖 11 1. 電源開關。按下開關以開啟 / 關閉電源。 2. AC-IN 連接埠。此連接埠用於連接電源線。 3. HDMI 連接埠。此連接埠用於連接 HDMI 相容裝置。 4. DisplayPort 輸入。此連接埠用於連接 DisplayPort 相容裝置。 5. USB 3.2 Gen1 Type-C。此連接埠用於連接 USB 上傳訊號線。該連接支援 USB 電源和資料傳輸。 本顯示器相容於 Super-Speed USB 3.2 Gen1 (5Gbps)。連接埠提供輸出電 壓 5V/3A、9V/3A、12V/3A、15V/3A 和 20V/4A 的最大 80W 電源。連接 USB Type-C 訊號線可輸入 DisplayPort 來源、輸出電源,並啟用顯示器的 USB Type-A 連接埠(下載)。連接 USB Type-C 對 Type-A 訊號線只會啟用顯示器 的 USB Type-A 連接埠(下載)。 6. 菊輪鍊 DisplayPort 輸出。此連接埠可供您連接多台 DisplayPort 相容顯示 器。 7.
具 1.3.3 圖示的連接埠符合 BC1.2 標準。 其他功能 1. 菊花鏈接 ( 適用於特定機型 ) 顯示器支援使用 DisplayPort 進行菊花鏈接。 菊花鏈接最多允許使用從訊號源傳送 至顯示器的視訊訊號,串接 4 台顯示器 ( 當輸入訊號源為 1920 x 1080@60Hz 並未 連接 USB-C 裝置時 ) 若要啟用菊花鏈接,請確定已傳輸訊號源。 此功能僅可在 OSD 選單中的 DisplayPort 串流為 DisplayPort 1.2 且訊號源自動 偵測為關閉時使用。 此外,您的電腦顯示卡至少須為 DP1.2 認證 (有 MST 選項) 。 若您將 DisplayPort 串流設為 DisplayPort 1.
1-6 第 1 章: 產品介紹
2.1 組裝顯示器支撐臂 / 底座 組裝顯示器底座: 1. 將顯示器正面朝下置於桌上。 2. 將支架總成的鉸接臂放在顯示器背面的隔間上。 3. 將底座安裝於支架,確定支架的調整片卡入底座的溝槽。 4. 旋緊固定螺絲將底座固定於支臂上。 建議您使用軟布覆蓋桌子表面,避免顯示器受損。 1 180° 2 2 1 底座螺絲尺寸: M6 x 16.
2.2 拆開支架 / 底座(適用於 VESA 壁掛式安裝) 此顯示器的可拆式支架/底座是專為 VESA 壁掛式安裝所設計。 拆開支架/底座: 1. 將顯示器正面朝下置於桌上。 2. 按下釋放鈕,然後將支架 / 底座自顯示器拉出。 2 1 建議您使用軟布覆蓋桌子表面,避免顯示器受損。 2-2 • VESA 壁掛架套件(100 x 100 公釐)需個別採購。 • 僅可使用最小重量 / 負荷 22.
2.
2.4 調整顯示器 • 為了取得最佳觀賞角度,我們建議您先從所有角度觀看顯示器,然後再將顯示器 調整到您認為最舒適的觀看角度。 • 變更角度時請握住底座,避免顯示器掉落。 • 您可以調整從 +35˚ 到 -5˚ 的顯示器角度,而且可以從左側或右側旋轉調整 180˚ (藉由取下止動螺絲)。您也可以調整顯示器的高度(+/- 150 公釐以內)。 -5° ~ +35° 150mm 180° (傾斜角度) 0° 180° (高度調整) (旋轉角度) 以顯示器為中心旋轉 1. 將顯示器抬升至最高位置。 2. 將顯示器傾斜至最大角度。 3.
2.
2.6 接線 依下列指示連接訊號線: • 連接電源線:將電源線的一端牢牢連接到顯示器的 AC 輸入埠,將另一端連接到 電源插座。 • 連接 DisplayPort/HDMI/USB Type-C* 訊號線: a. 將 DisplayPort/HDMI/USB Type-C* 訊號線的一端,插入顯示器的 DisplayPort/HDMI/USB Type-C 插孔。 b. 將 DisplayPort/HDMI/USB Type-C* 訊號線的另一端,接至電腦的 DisplayPort/HDMI/USB Type-C 插孔。 建議使用 USB 合格 Type-C 訊號線。如果訊號來源支援 DP Alt 模式,即可傳輸 全部的視訊、音訊和資料訊號。 • 使用耳機:HDMI/DisplayPort/USB Type-C訊號輸入時,將插頭端連接到顯示器 的耳機插孔。 • 若要使用 USB 上傳連接埠/下載連接埠功能: » 上傳連接埠:使用 USB Type-C 訊號線,將 Type-C 接頭的一端插入做 ),並將另一端 為上傳連接埠的顯示器 USB 3.
USB Type-C RJ45 或 完成接線後,可從 OSD 選單的「輸入選擇」項目中選擇所需的訊號。 如需更換電源線或連接線,請聯絡 ASUS 客戶服務。 2.7 開啟顯示器電源 按下電源按鈕 。關於電源按鈕的位置,請參閱第 1-2 頁。電源指示燈 色,表示已開啟顯示器的電源。 2.
若您想要將顯示器網路攝影機設為預設設定,您需要停用筆記型電腦內建網 路攝影機。 若要識別並停用筆記型電腦內建網路攝影機,請依照以下說明 進行: 在 USB2.0 HD UVC WebCam 上按滑鼠右鍵,並按一下內容,以開啟 USB2.
對於 BE/C6 網路攝影機系列,顯示器網路攝影機的硬體識別碼會如以下所示: 若筆記型電腦網路攝影機擁有不同的 BE/C6 網路攝影機系列顯示器網路攝影機硬體 識別碼上按滑鼠右鍵,然後按一下停用。 ASUS BE24ECSNK 系列 LCD 顯示器 2-9
將會顯示以下訊息: 按一下是。 現在已停用筆記型電腦網路攝影機,並將顯示器網路攝影機作為預設設 定使用。 重新啟動筆記型電腦。 2.
按一下開啟音效設定,以進入音效設定介面。 進入音效設定介面,然後選擇音效控制台。 若從顯示器將 USB 纜線與 HDMI 或 DP 纜線連接至電腦, 按一下 ASUS BE/C6 網路攝影機系列設為預設,顯示器喇叭將作為預設設定使用。 螢幕擷取畫面上的 BE***/C**** 代表此顯示器的型號,可能與實際設計不同。 ASUS BE24ECSNK 系列 LCD 顯示器 2-11
按一下確定,以離開音效設定。 音效設定便會將BE/C6 網路攝影機系列設為預設。 若只有 HDMI 或 DP 纜線從顯示器連接至電腦,請勾選 ASUS BE/C6 顯示器設為預 設,顯示器喇叭將作為預設設定使用。 2-12 第 2 章: 設定
音效設定便會將ASUS BE/C6設為預設。 ASUS BE24ECSNK 系列 LCD 顯示器 2-13
2-14 第 2 章: 設定
3.1 OSD(螢幕功能顯示)選單 3.1.1 如何重新設定 ASUS BE24ECSNK 標準模式 DisplayPort 1920 x 1080 @ 60Hz 80W Splendid 風景模式 標準模式 劇院模式 遊戲模式 夜間模式 sR GB 模 式 閱讀模式 暗房模式 1. 按下 2. 向上 / 下 / 左 / 右移動 5 向按鈕,以瀏覽各項功能。 反白所需的功能並按下 5 向按鈕,以啟用功能。 若所選功能提供子功能表,向上 / 下移動 5 向 按鈕,以瀏覽子選單功能。 反白所需的子選單功能,並按下 5 向按鈕或移 動 5 向按鈕以啟用功能。 5 向按鈕啟用 OSD 選單。 3. 向上/下移動 4.
3.1.2 1.
2.
3.
4. 影像 在此選單中設定影像相關設定。 影像 ASUS BE24ECSNK 標準模式 DisplayPort 1920 x 1080 @ 60Hz 80W 影像銳利 Trace Free 畫面控制 Vi vi dPi xel AS C R • 影像銳利:調整範圍為 0 到 100。 • Trace Free:調整顯示器的反應時間。 • 畫面控制:將長寬比調整成全螢幕、4:3、1:1(選用)或 OverScan(選 用)。 4:3 只能在輸入訊號源為 4:3 格式時使用。 OverScan 僅可用於 HDMI 輸入 訊號源。 5.
• 音量:調整範圍為 0 到 100。 • 靜音:開啟和關閉顯示器聲音。 • 音源:決定顯示器的音效來源。 6. AI 麥克風 您可以調整麥克風相關設定。 AI 麥克風 ASUS BE24ECSNK 標準模式 DisplayPort 1920 x 1080 @ 60Hz 80W 降噪 B eamformi ng • 降噪: 除使用者人聲外,可以調整降噪的幅度。 • Beamforming: 調整麥克風接收範圍值。 7.
• 輸入選擇: 您可以選擇所需的輸入訊號源。 • QuickFit: 您無須試印副本,即可直接在螢幕上預覽文件或相片版面配 置。 * 格線圖樣: 這可以加快設計者及使用者在頁面上組織內容及配置版面 的速度,並讓風格及樣貌保持一致。 Alignment Grid 2 Alignment Grid 1 * 紙張大小: 您可以在螢幕上檢視實際大小的文件。 Letter B5 * 相片: QuickFit 功能可顯示各種實際的相片大小,為攝影師或其他使 用者提供準確的檢視畫面,並在螢幕上以實際大小的顯示方式編輯相 片。 4x6 3x5 2x2 • ECO Mode:降低耗電量。 • Webcam:啟用或停用網路攝影機功能。 • 節能模式: • 8x10 5x7 * 「初級階層」能夠讓 USB 下載連接埠/USB Type-C 連接埠在顯示 器進入節能模式時將外接裝置充電。 * 「深度階層」不允許所有連接埠將外接裝置充電,並避免顯示器進 入節能模式時自動偵測 USB 訊號。 選單設定: ASUS BE24ECSNK 系列 LCD 顯示器 3-7
* 調整 OSD 的逾時時間,範圍介於 10 至 120 秒。 * 啟用或停用 DDC/CI 功能。 * 將 OSD 背景從不透明調整至透明。 • 語言:提供 22 種語言任您選擇,包括英文、法文、德文、義大利文、西 班牙文、荷蘭文、葡萄牙文、俄文、捷克文、克羅埃西亞文、波蘭文、羅 馬尼亞文、匈牙利文、土耳其文、簡體中文、繁體中文、日文、韓文、泰 文、印尼文、波斯文、烏克蘭文。 • DisplayPort 串流:相容於顯示卡。依顯示卡 DP 版本選擇 DisplayPort 1.1 或 DisplayPort 1.2。 • 按鍵鎖:停用所有功能鍵。按下 功能。 • 顯示資訊:顯示顯示器的資訊。 • 電源指示燈:開啟/關閉電源 LED 指示燈。 • 電源鍵鎖:啟用或停用電源鍵。 • 訊號源自動偵測:啟用或停用訊號源自動偵測功能。 • 恢復出廠模式:按「是」即可還原預設設定值。 8.
3.2 規格總覽 面板類型 面板大小 TFT LCD 23.8 吋(16:9、60.45 公分)寬螢幕 最大解析度 畫素間距 亮度(一般) 對比比例(一般) 對比比例(最大) 視角(水平/垂直)CR > 10 顯示色彩 回應時間 Splendid 影像增強技術 Splendid 選項 色溫選項 訊號輸入 1920 x 1080 0.2745 公釐 x 0.2745 公釐 300 cd/m2 1000:1 100,000,000:1(ASCR 開啟時) 178˚/178˚ 16.7 M < 5 毫秒 有 8 種影像預設模式 4 種色溫 DisplayPort v1.2、HDMI v1.4、DisplayPort 透過 USB Type C DisplayPort v1.2 有 有(DisplayPort、HDMI、USB Type C ) 2 個 2 W 立體聲、RMS 資料上傳連接埠 x 1、資料下載連接埠 x 4 RJ45 x 1 黑 白色(開機)/琥珀色(待機) +35˚~ -5˚ +90˚~ -90˚ +180˚~ -180˚ 150 公釐 有 AC:100 ~ 240 V 開機:< 17.
配件 規範和標準 快速使用指南、保固卡、電源線、HDMI 纜線 (選購)、DisplayPort 纜線 (選購)、USB C 轉 A 訊號線 (選配)、USB C 轉 C 訊號線(選配)、 MiniPC 套件 (選購) UL、FCC、ICES-003、EPEAT Silver、CB、 CE、ErP、WEEE、EU Energy label、 ISO 9241-307、UkrSEPRO、CU、Ru RoHs、 CCC、China RoHs、CEL、BSMI、RCM、MEPS、 VCCI、PSE、PC-Recycle、J-MOSS、KC、KCC、 e-Standby、Energy Star 8.0、TCO 9.
外型尺寸 3.
3.
3.5 支援的操作模式 解析度頻率 640x480 640x480 640x480 640x480 720x400 800x600 800x600 800x600 800x600 832X624 1024x768 1024x768 1024x768 1152x864 1280x720 1280x768 1280x800 1280x960 1280x1024 1280x1024 1360x768 1366x768 1440x900 1600x1200 1680x1050 1920x1080 1920x1080 水平頻率 (KHz) 31.47(N) 35.00(N) 37.87(N) 37.5(N) 31.47(N) 35.16(P) 37.88(P) 48.08(P) 46.86(P) 49.72(P/N) 48.36(N) 56.476(N) 60.02(N) 67.5(P/N) 45.00(P) 47.78(P) 49.7(P) 60.00(P) 63.98(P) 79.98(P) 47.712(P) 47.712(P) 55.94(N) 75.00(P) 65.29(P) 67.
時序名稱 480p 720p60 576p 720p50 1080p60 1080p50 3-14 像素格式 720 x 480 1280 x 720 720 x 576 1280 x 720 1920 x 1080 1920 x 1080 水平頻率 (kHz) 31.469 45 31.25 37.5 67.5 56.25 垂直頻率 (Hz) 60 60 50 50 60 50 像素率 (MHz) 27 74.25 27 74.25 148.5 148.