® MEW-L Socket 370 Intel® 810 Motherboard USER’S MANUAL
USER'S NOTICE No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS CONTACT INFORMATION ASUSTeK COMPUTER INC. (Asia-Pacific) Marketing Address: Telephone: Fax: Email: 150 Li-Te Road, Peitou, Taipei, Taiwan 112 +886-2-2894-3447 +886-2-2894-3449 info@asus.com.tw Technical Support MB/Others (tel): +886-2-2890-7121 (English) Notebook (tel): +886-2-2890-7122 (English) Desktop/Server (tel): +886-2-2890-7123 (English) Fax: +886-2-2895-9254 Email: tsd@asus.com.tw Newsgroup: news2.asus.com.tw WWW: www.asus.com.tw FTP: ftp.asus.com.
CONTENTS 1. INTRODUCTION ............................................................................. 7 1.1 How This Manual Is Organized .................................................. 7 1.2 Item Checklist ............................................................................. 7 2. FEATURES ........................................................................................ 8 2.1 The ASUS MEW-L Motherboard ............................................... 8 2.1.1 Specifications .................
CONTENTS 4.5 Power Menu .............................................................................. 68 4.5.1 Power Up Control ............................................................ 70 4.5.2 Hardware Monitor ............................................................ 72 4.6 Boot Menu ................................................................................ 73 4.7 Exit Menu ................................................................................. 75 5. SOFTWARE SETUP .................
FCC & DOC COMPLIANCE Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
1. INTRODUCTION 1. INTRODUCTION Sections/Checklist 1.
2. FEATURES 2.1 The ASUS MEW-L Motherboard The MEW-L motherboard from ASUS is carefully designed for the demanding PC user who wants many smart features in a small package. So what’s so smart about the ASUS MEW-L motherboard? 2.1.1 Specifications • 2. FEA TURES Specifications • • • • • • • • • • • • 8 Latest Intel Socket 370 Processor Support! Supports Intel’s Celeron processor designed for Socket 370 and packaged in Plastic Pin Grid Array (PPGA).
2. FEATURES • • • Monitoring for your PC’s Health! Provided ASUS PC Probe or Intel LDCM allows PC health monitoring. Enhanced ACPI & Anti-Boot Virus Protection! Programmable BIOS (Flash EEPROM), offering enhanced ACPI for Windows 98 compatibility, built-in firmware-based virus protection, and autodetection of most devices for virtually automatic setup. Smart BIOS! 4Mbit firmware gives a new easy-to-use interface which provides more control and protection over the motherboard.
2. FEATURES 2.1.3 Performance • • 2. FEA TURES Performance • • • • • • • • 10 UltraPerformance! Onboard IDE Bus Master controller with two connectors that support four IDE devices in two channels. Supports UltraDMA/66, UltraDMA/33 (IDE DMA Mode 2), PIO Modes 3 & 4, and supports Enhanced IDE devices, such as Tape Backup, CD-ROM, CD-R/RW, and LS-120 drives. Dual Speeds! CPU frequency can operate at either 66MHz or 100MHz while system memory operates at either 100MHz or 66MHz.
2. FEATURES 2.1.4 Intelligence • • • • • • • Fan Status Monitoring and Alarm! To prevent system overheat and system damage, the CPU, power supply, and system fans can be monitored for RPM and failure. All the fans are set for its normal RPM range and alarm thresholds. Temperature Monitoring and Alert! To prevent system overheat and system damage, this motherboard supports Socket 370 processor thermal sensing and auto-protection.
2. FEATURES 2.2 Motherboard Part Definitions The following are part descriptions for the motherboard parts shown on the next page. 2.
2. FEATURES 2.3 Motherboard Part Locations 1 2 3 4 5 6 7 8 9 27 2. FEA TURES Part Locations 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 NOTE: The ISA model is shown above. One or two ISA slots are optional at the time of purchase. The model with two ISA will have only 5 PCI slots.
3. HARDWARE SETUP 3.
3. HARDWARE SETUP 3.2 Layout Contents Motherboard Settings 1) JEN 2) VIO 3) AUDIO CODEC 4) LAN_EN 5) LAN_PWR 6) SAFE_MD 7) NO_REBOOT 8) DSW p.18 p.19 p.19 p.20 p.20 p.21 p.21 p.22 JumperFree™ Mode (Enable/Disable) I/O Voltage Setting (Normal/+3.66V) Onboard Audio Setting (Enable/Disable) Onboard LAN Setting (Enable/Disable) Onboard LAN Power Setting (Normal/Standby) Safe Mode (Normal/Safe Mode) Automatic Timeout Reboot (Normal/No Reboot) CPU External Clock (BUS) Frequency Setting p.24 p.26 p.27 p.27 p.
3. HARDWARE SETUP 20) 21) 22) 23) 24) 25) 26) 27) 28) 29) 30) 31) SMB DFP INT MIC CHA ATXPWR SPEAKER (PANEL) KEYLOCK (PANEL) PLED (PANEL) RESET (PANEL) PWRSW (PANEL) SMI (PANEL) LED (PANEL) p.39 SMBus Connector (5-1 pins) p.39 Digital LCD Header (20-1 pins) (optional) p.40 Internal Microphone Connector (3 pins) p.41 Chassis Intrusion Connector (2 pins) p.41 ATX Power Supply Connector (20 pins) p.43 System Warning Speaker Connector (4 pins) p.43 Keyboard Lock Switch Lead (2 pins) p.
3. HARDWARE SETUP 3.3 Hardware Setup Procedure Before using your computer, you must complete the following steps: • Check Motherboard Settings • Install Memory Modules • Install the Central Processing Unit (CPU) • Install Expansion Cards • Connect Ribbon Cables, Panel Wires, and Power Supply 3.4 Motherboard Settings This section explains in detail how to change your motherboard’s function settings through the use of switches and/or jumpers. 3.
3. HARDWARE SETUP 1) JumperFree™ Mode Setting (JEN) This jumper allows you to enable or disable the JumperFree™ mode. The JumperFree™ mode allows processor settings to be made through the BIOS setup (see 4.4 Advanced Menu). NOTE: For JumperFree™ mode, all dip switches (DSW) must be set to OFF. Setting JEN Disable (Jumper) [1-2] Enable (JumperFree) [2-3] (default) 0 1 0 1 0 1 JEN 1 2 3 1 2 3 Jumper JumperFree ® 3.
3. HARDWARE SETUP 2) I/O Voltage Setting (VIO) This jumper allows you to select the voltage supplied to the DRAM, chipset, PCI, and the CPU’s I/O buffer. The default voltage should be used unless processor overclocking requires a higher voltage. Setting VIO Normal [1-2] (default) 3.66V [2-3] 0 1 0 1 0 1 VIO 1 2 3 1 2 3 Normal Add 0.1 Volt ® 3.
3. HARDWARE SETUP 4) Onboard LAN Setting (LAN_EN) available on LAN model only The onboard LAN may be enabled or disabled by this jumper. Setting LAN_EN Enable [1-2] (default) Disable [2-3] 01 01 01 LAN_EN ® MEW-L 1 2 3 1 2 3 Enable Disable 3. H/W SETUP Motherboard Settings MEW-L LAN Setting 5) Onboard LAN Power Setting (LAN_PWR) available on LAN model only The onboard LAN power may be set to normal or standby power. Select Normal if you do not have a power supply with 720mA standby power.
3. HARDWARE SETUP 6) Safe Mode Setting (SAFE_MD) Usually socket 370 processors have locked frequency multiples. In this case, there is no way to exceed the specified multiple whether through motherboard settings or BIOS setup. With unlocked socket 370 processors, exceeding the specified multiple is possible through BIOS setup. Exceeding the specified multiple may result in hanging during bootup. If this occurs, enable Safe Mode to force a multiple of 2 in order to enter BIOS setup to correct the problem.
3. HARDWARE SETUP 8) CPU External Frequency Setting (DSW) This option tells the clock generator what frequency to send to the CPU, DRAM, and the PCI bus. This allows the selection of the CPU’s External frequency. The CPU External Frequency multiplied by the Frequency Multiple equals the CPU’s Internal frequency (the advertised CPU speed). NOTE: You may set the memory speed independently from the CPU External Frequency.
3. HARDWARE SETUP External Frequency Table for Intel Celeron (PPGA) Processors The following table is for use by experienced motherboard installers only. Overclocking can result in system instability or even shortening the life of the processor. Bold settings are also shown on the previous page. SDRAM (MHz) 101.71 105.00 108.01 100.00 109.51 112.50 115.50 117.01 120.00 124.51 126.74 150.00 129.12 132.00 135.00 142.50 49.90 100.00 74.85 66.58 82.84 89.81 94.80 100.50 104.78 111.77 114.77 100.00 123.75 132.
3. HARDWARE SETUP 3.5 System Memory (DIMM) NOTE: No hardware or BIOS setup is required after adding or removing memory. This motherboard uses only Dual Inline Memory Modules (DIMMs). Sockets are available for 3.3Volt (power level) unbuffered Synchronous Dynamic Random Access Memory (SDRAM) of 16, 32, 64, 128MB, or 256MB. This chipset does not support ECC. However, ECC memory modules may still be used, but the ECC function will not be available.
3. HARDWARE SETUP 3.5.2 DIMM Installation Insert the module(s) as shown. Because the number of pins are different on either side of the breaks, the module will only fit in the orientation shown. DIMMs are longer and have different pin contact on each side and therefore have a higher pin density. SIMMs have the same pin contact on both sides. Lock 0 1 0 1 0 1 88 Pins FRONT ® MEW-L 3. H/W SETUP System Memory 60 Pins 20 Pins MEW-L 168-Pin DIMM Sockets The DIMMs must be 3.
3. HARDWARE SETUP 3.6 Central Processing Unit (CPU) The motherboard provides a ZIF Socket 370. The CPU that came with the motherboard should have a fan attached to it to prevent overheating. If this is not the case, then purchase a fan before you turn on your system. WARNING! Be sure that there is sufficient air circulation across the processor’s heatsink by regularly checking that your CPU fan is working.
3. HARDWARE SETUP 3.7 Expansion Cards WARNING! Unplug your power supply when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 3.7.1 Expansion Card Installation Procedure ASUS MEW-L User’s Manual 3. H/W SETUP Expansion Cards 1. Read the documentation for your expansion card and make any necessary hardware or software settings for your expansion card, such as jumpers. 2.
3. HARDWARE SETUP 3.7.2 Assigning IRQs for Expansion Cards Some expansion cards need an IRQ to operate. Generally, an IRQ must be exclusively assigned to one use. In a standard design, there are 16 IRQs available but most of them are already in use, leaving 6 IRQs free for expansion cards. If your motherboard has PCI audio onboard, an additional IRQ will be used. If your motherboard also has MIDI enabled, another IRQ will be used, leaving 4 IRQs free.
3. HARDWARE SETUP Interrupt Request Table PCI slot 1 PCI slot 2 PCI slot 3 PCI slot 4 PCI slot 5 PCI slot 6 Onboard VGA Onboard audio/AMR/SMBus Onboard LAN USB INT-A shared ---shared -shared ---- INT-B -shared -------shared --- INT-C --shared --shared --shared -- INT-D ---shared -----shared 3. H/W SETUP Expansion Cards IMPORTANT: If using PCI cards on shared slots, make sure that the drivers support “Share IRQ” or that the cards do not need IRQ assignments.
3. HARDWARE SETUP 3.7.3 Assigning DMA Channels for ISA Cards Some ISA cards, both legacy and PnP, may also need to use a DMA (Direct Memory Access) channel. DMA assignments for this motherboard are handled the same way as the IRQ assignment process described earlier. To select a DMA channel, see PCI/ PNP ISA DMA Resource Exclusion in 4.4.3 PCI Configuration. NOTE: The onboard audio by default uses DMA1.
3. HARDWARE SETUP 3.8 External Connectors WARNING! Some pins are used for connectors or power sources. These are clearly distinguished from jumpers in the Motherboard Layout. Placing jumper caps over these connector pins will cause damage to your motherboard. IMPORTANT: Ribbon cables should always be connected with the red stripe to Pin 1 on the connectors. Pin 1 is usually on the side closest to the power connector on hard drives and CD-ROM drives, but may be on the opposite side on floppy disk drives.
3. HARDWARE SETUP 3) Universal Serial Bus Ports 1 & 2 (Two black 4-pin USB) Two USB ports are available for connecting USB devices. USB 1 Universal Serial Bus (USB) 2 4) Parallel Port Connector (Burgundy 25-pin PRINTER) You can enable the parallel port and choose the IRQ through Onboard Parallel Port (see 4.4.2 I/O Device Configuration). NOTE: Serial printers must be connected to the serial port. 3.
3. HARDWARE SETUP 6) Monitor Output Connector (Blue 15-pin VGA) This connector is for output to a VGA-compatible device. VGA Monitor (15-pin female) 7) Joystick/MIDI Connector (Gold 15-pin GAME_AUDIO) (optional) You may connect game joysticks or game pads to this connector for playing games. Connect MIDI devices for playing or editing professional audio. 3.
3. HARDWARE SETUP 10) Primary / Secondary IDE Connectors (Two 40-1 pin IDE) These connectors support the provided IDE hard disk ribbon cable. After connecting the single end to the board, connect the two plugs at the other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accordingly. Please refer to your hard disk documentation for the jumper settings. BIOS now supports specific device bootup (see Boot Sequence in 4.
3. HARDWARE SETUP 12) Wake-On-LAN Connector (3-pin WOL_CON) This connector connects to a LAN card with a Wake-On-LAN output, such as the ASUS PCI-L101 Ethernet card (not required for onboard LAN model). The connector powers up the system when a wakeup packet or signal is received through the LAN card. IMPORTANT: This feature requires that Wake On LAN is set to Enabled (see 4.5.1 Power Up Control) and that your system has an ATX power supply with at least 720mA +5V standby power.
3. HARDWARE SETUP 14) IDE Activity LED Lead (2-pin IDELED) This lead supplies power to the cabinet’s IDE activity LED. Read and write activity by devices connected to the Primary or Secondary IDE connectors will cause the LED to light up. 0 1 0 1 0 1 TIP: If the case-mounted LED does not light, try reversing the 2-pin plug. ® MEW-L IDELED MEW-L IDE Activity LED 3.
3. HARDWARE SETUP 16) Internal Audio Connectors (4-pin VIDEO, AUX, CD, TAD) These connectors allow you to receive stereo audio input from such sound sources as a CD-ROM, TV tuner, or MPEG card. The TAD connector allows the onboard audio to interface with a voice modem card with a similar connector. It also allows the sharing of mono_in (such as a phone) and mono_out (such as a speaker) between the onboard audio and the voice modem card.
3. HARDWARE SETUP 18) Standard IR (SIR) (5-pin) and Consumer IR (CIR) (5-1 pin) Connectors This connector supports an optional wireless transmitting and receiving infrared module. This module mounts to a small opening on system cases that support this feature. You must also configure the setting through UART2 Use Infrared (see 4.4.2 I/O Device Configuration) to select whether UART2 is directed for use with COM2 or IrDA.
3. HARDWARE SETUP 20) SMBus Connector (5-1 pin SMB) This connector allows you to connect SMBus (System Management Bus) devices. SMBus devices communicate by means of the SMBus with an SMBus host and/or other SMBus devices. SMBus is a specific implementation of an I2C bus, which is a multi-device bus; that is, multiple chips can be connected to the same bus and each one can act as a master by initiating data transfer. +5V Ground SMBDATA 0 1 0 1 SMBCLK 0 1 ® MEW-L 1 3.
3. HARDWARE SETUP 22) Internal Microphone Connector (3 pin INT MIC) This connector allows you to connect a chassis mounted microphone to the motherboard instead of having to attach an external microphone. 0 1 0 1 MIC Power MIC Input Ground 0 1 1 3 ® MEW-L INT MIC MEW-L Internal Microphone Connector 3.
3. HARDWARE SETUP 23. Chassis Intrusion Lead (2-pin CHA) This lead is for a chassis designed for chassis intrusion detection. After-market toggle switches may also be installed to the chassis panel or on any removable components. Two wires should be available from the chassis to connect to this lead. When any chassis component is removed, the contact should open and the motherboard will record a chassis intrusion event.
3. HARDWARE SETUP The following PANEL illustration is used for items 25-31 0 1 0 1 0 1 * Requires an ATX power supply. Speaker Connector Reset Switch ATX Power Switch ® MEW-L Keyboard Lock Power LED 3.
3. HARDWARE SETUP 25) System Warning Speaker Connector (4-pin SPEAKER) This 4-pin connector connects to the case-mounted speaker. You may leave this disconnected if you connect the chassis speaker to the internal speaker connector. All three sources (LINE_OUT, INT_SPKA, SPEAKER) will allow you to hear system beeps and warnings. Only LINE_OUT will allow you to hear system beeps before the integrated audio has been properly initialized.
3. HARDWARE SETUP (This page was intentionally left blank) 3.
3. HARDWARE SETUP 3.9 Power Connection Procedures 1. After all connections are made, close the system case cover. 2. Be sure that all switches are OFF (in some systems, marked with ). 3. Connect the power supply cord into the power supply located on the back of your system case according to your system user’s manual. 4. Connect the power cord into a power outlet that is equipped with a surge protector. 3. H/W SETUP Power Connections 5. You may then turn ON your devices in the following order: a.
4. BIOS SETUP 4.1 Managing and Updating Your BIOS 4.1.1 Upon First Use of the Computer System It is recommended that you save a copy of the original motherboard BIOS along with a Flash Memory Writer utility (AFLASH.EXE) to a bootable floppy disk in case you need to reinstall the BIOS later. AFLASH.EXE is a Flash Memory Writer utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the motherboard. This file works only in DOS mode.
4. BIOS SETUP 5. Select 1. Save Current BIOS to File from the Main menu and press . The Save Current BIOS To File screen appears. 6. Type a filename and the path, for example, A:\XXX-XX.XXX and then press . 4.1.2 Updating BIOS Procedures WARNING! Only update your BIOS if you have problems with your motherboard and you know that the new BIOS revision will solve your problems. Careless updating can result in your motherboard having more problems! ASUS MEW-L User’s Manual 4.
4. BIOS SETUP 6. When prompted to confirm the BIOS update, press Y to start the update. 7. The utility starts to program the new BIOS information into the flash ROM. The boot block will be updated automatically only when necessary. This will minimize the chance that a failed update will prevent your system from booting up. When the programming is finished, Flashed Successfully will be displayed. 4. BIOS SETUP Updating BIOS 8. Follow the onscreen instructions to continue.
4. BIOS SETUP 4.2 BIOS Setup Program This motherboard supports a programmable EEPROM that can be updated using the provided utility as described in 4.1 Managing and Updating Your BIOS. The utility is used if you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section describes how to configure your system using this utility. Even if you are not prompted to use the Setup program, at some time in the future you may want to change the configuration of your computer.
4. BIOS SETUP 4.2.1 BIOS Menu Bar The top of the screen has a menu bar with the following selections: MAIN Use this menu to make changes to the basic system configuration. ADVANCED Use this menu to enable and make changes to the advanced features. POWER Use this menu to configure and enable Power Management features. BOOT Use this menu to configure the default system device used to locate and load the Operating System. EXIT Use this menu to exit the current menu or specify how to exit the Setup program.
4. BIOS SETUP General Help In addition to the Item Specific Help window, the BIOS setup program also provides a General Help screen. This screen can be called up from any menu by simply pressing or the + combination. The General Help screen lists the legend keys with their corresponding alternates and functions. Saving Changes and Exiting the Setup Program See 4.7 Exit Menu for detailed information on saving changes and exiting the setup program.
4. BIOS SETUP 4.3 Main Menu When the Setup program is accessed, the following screen appears: 4. BIOS SETUP Main Menu System Time [XX:XX:XX] Sets your system to the time that you specify (usually the current time). The format is hour, minute, second. Valid values for hour, minute and second are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59). Use the or + keys to move between the hour, minute, and second fields.
4. BIOS SETUP 4.3.1 Primary & Secondary Master/Slave 4. BIOS SETUP Master/Slave Drives NOTE: Before attempting to configure a hard disk drive, make sure you have the configuration information supplied by the manufacturer of the drive. Incorrect settings may cause your system to not recognize the installed hard disk. To allow the BIOS to detect the drive type automatically, select [Auto]. Type [Auto] Select [Auto] to automatically detect an IDE hard disk drive.
4. BIOS SETUP IMPORTANT: If your hard disk was already formatted on an older previous system, incorrect parameters may be detected. You will need to enter the correct parameters manually or use low-level format if you do not need the data stored on the hard disk. If the parameters listed differ from the ones used when the disk was formatted, the disk will not be readable.
4. BIOS SETUP ASUS MEW-L User’s Manual 4. BIOS SETUP Master/Slave Drives Head This field configures the number of read/write heads. Refer to your drive documentation to determine the correct value to enter into this field. NOTE: To make changes to this field, the Type field must be set to [User Type HDD] and the Translation Method field must be set to [Manual]. Sector This field configures the number of sectors per track.
4. BIOS SETUP Other options for “Type:” are: [CD-ROM] - for IDE CD-ROM drives [LS-120] - for LS-120 compatible floppy disk drives [ZIP-100] - for ZIP-100 compatible disk drives [MO] - for IDE magneto optical disk drives [Other ATAPI Device] - for IDE devices not listed here After using the legend keys to make your selections on this sub-menu, press the key to exit back to the Main menu.
4. BIOS SETUP Forgot the password? If you forgot the password, you can clear the password by erasing the CMOS Real Time Clock (RTC) RAM. The RAM data containing the password information is powered by the onboard button cell battery. To erase the RTC RAM: (1) Unplug your computer, (2) Short the solder points, (3) Turn ON your computer, (4) Hold down during bootup and enter BIOS setup to re-enter user preferences.
4. BIOS SETUP 4.4 Advanced Menu 4. BIOS SETUP Advanced Menu CPU Speed [Manual] When the motherboard is set to JumperFree™ mode, this field allows you to select the internal speed of your CPU. Select [Manual] if you want to make changes to the subsequent four fields. Configuration options: [Manual] [266MHz] [300MHz] [333MHz] [366MHz] [400MHz] [433MHz] [466MHz] CPU Core:Bus Freq. Multiple (when CPU Speed is set to [Manual]) This field is for unlocked processors only.
4. BIOS SETUP CPU Vcore (when CPU Speed is set to [Manual]) This field displays the core voltage supplied to the CPU. If you want to set it manually, always refer to the CPU documentation for the reasonable voltage range. Configuration options: [2.40V] [2.30V] [2.20V] [2.10V] [2.05V] [2.00V] CPU Level 1 Cache, CPU Level 2 Cache [Enabled] These fields allow you to choose from the default of [Enabled] or choose [Disabled] to turn ON or OFF the CPU’s Level 1 and Level 2 built-in cache.
4. BIOS SETUP 4.4.1 Chip Configuration (scroll down to see more items, as shown here) 4. BIOS SETUP Chip Configuration SDRAM Configuration [By SPD] This sets the optimal timings for items 2–4, depending on the memory modules that you are using. Default setting is [By SPD], which configures items 2–4 by reading the contents in the SPD (Serial Presence Detect) device.
4. BIOS SETUP SDRAM Cycle Time (Tras, Trc) [5T, 7T] This feature controls the number of SDRAM clocks used per access cycle. Configuration options: [5T, 7T] [6T, 8T] SDRAM Address Setup Time [1T Delay] Configuration options: [No Delay] [1T Delay] SDRAM Page Closing Policy [All Banks] This feature controls whether the graphic and memory controller hub will precharge one or all banks after a page miss.
4. BIOS SETUP 4.4.2 I/O Device Configuration (scroll down to see more items, as shown here) 4. BIOS SETUP I/O Device Config. Onboard AC97 Modem Controller, Audio Controller [Auto] [Auto] allows the motherboard’s BIOS to detect whether you are using any modem/audio device. If a modem/audio device is detected, the onboard modem/audio controller will be enabled; if no modem/audio device is detected, the onboard modem/audio controller will be disabled.
4. BIOS SETUP UART2 Use Standard Infrared [Disabled] When enabled, this field activates the onboard standard infrared feature and sets the second serial UART to support the infrared module connector on the motherboard. If your system already has a second serial port connected to the onboard COM2 connector, it will no longer work if you enable the infrared feature. See IrDA-Compliant Infrared Module Connector in 3.8 External Connectors.
4. BIOS SETUP 4.4.3 PCI Configuration Slot 1/5, Slot 2, Slot 3/6, Slot 4 IRQ [Auto] These fields set how IRQ use is determined for each PCI slot. The default setting for each field is [Auto], which uses auto-routing to determine IRQ use. Configuration options: [Auto] [NA] [3] [4] [5] [7] [9] [10] [11] [12] [14] [15] 4. BIOS SETUP PCI Configuration PCI/VGA Palette Snoop [Disabled] Some nonstandard VGA cards, such as graphics accelerators or MPEG Video Cards, may not show colors properly.
4. BIOS SETUP USB Function [Enabled] This motherboard supports Universal Serial Bus (USB) devices. Set to [Enabled] if you want to use USB devices. Configuration options: [Disabled] [Enabled] ONB VGA BIOS First [No] This field, when set to [Yes], gives priority to the onboard VGA BIOS over other VGA controllers. Configuration options: [No] [Yes] 4.
4. BIOS SETUP PCI/PNP ISA DMA Resource Exclusion 4. BIOS SETUP PCI Configuration DMA x Used By ISA [No/ICU] These fields indicate whether or not the displayed DMA channel for each field is being used by a legacy (non-PnP) ISA card. The default setting indicates either that the displayed DMA channel is not used or an ICU is being used to determine if an ISA card is using that channel.
4. BIOS SETUP ISA MEM Block BASE [No/ICU] This field allows you to set the base address and block size of a legacy ISA card that uses any memory segment within the C800 and DFFF address range. If you have such a card and you are not using an ICU to specify its address range, select a base address from the six available options; the ISA MEM Block SIZE field will then appear for selecting the block size.
4. BIOS SETUP 4.5 Power Menu The Power menu allows you to reduce power consumption. This feature turns OFF the video display and shuts down the hard disk after a period of inactivity. 4. BIOS SETUP Power Menu Power Management [User Define] This option must be enabled to use any of the automatic power saving features. If this menu item is set to [Disabled], power management features will not function regardless of other field settings on this menu.
4. BIOS SETUP Video Off Option [Suspend -> Off ] This field determines when to activate the video OFF feature for monitor power management. Configuration options: [Always On] [Suspend -> Off] Video Off Method [DPMS OFF] This field defines the video OFF features. The DPMS (Display Power Management System) feature allows the BIOS to control the video display card if it supports the DPMS feature. [Blank Screen] only blanks the screen (use this for monitors without power management or “green” features.
4. BIOS SETUP 4.5.1 Power Up Control AC PWR Loss Restart [Disabled] This allows you to set whether you want your system to reboot after the power has been interrupted. [Disabled] leaves your system OFF and [Enabled] reboots your system. Configuration options: [Disabled] [Enabled] 4. BIOS SETUP Power Up Control PWR Up On Modem Act [Disabled] This allows either settings of [Enabled] or [Disabled] for powering up the computer when the modem receives a call while the computer is in Soft-off mode.
4. BIOS SETUP Wake On PS2 KB/Mouse [Disabled] Set this field to [Enabled] if you wish to use your PS2 keyboard (by pressing the spacebar) or PS2 mouse (by clicking on the left button) to power up your computer. This feature requires an ATX power supply that can supply at least 300mA on the +5VSB lead. The default is set to [Disabled] because not all computers have the appropriate ATX power supply. Your computer will not power ON if you set this to [Enabled] and do not have the appropriate ATX power supply.
4. BIOS SETUP 4.5.2 Hardware Monitor MB Temperature, CPU Temperature [xxxC/xxxF] The onboard hardware monitor is able to detect the MB (motherboard) and CPU temperatures. Set to [Ignore] only if necessary. 4. BIOS SETUP Hardware Monitor CPU Fan, Power Fan, Chassis Fan Speed [xxxxRPM] The onboard hardware monitor is able to detect the CPU fan speed, power supply fan speed, and the chassis fan speed in rotations per minute (RPM). The presence of the fans is automatically detected.
4. BIOS SETUP 4.6 Boot Menu Boot Sequence 4. BIOS SETUP Boot Menu The Boot menu allows you to select among the four possible types of boot devices listed using the up and down arrow keys. By using the <+> or key, you can promote devices and by using the <-> key, you can demote devices. Promotion or demotion of devices alters the priority which the system uses to search for a boot device on system power up.
4. BIOS SETUP Plug & Play O/S [No] This field allows you to use a Plug-and-Play (PnP) operating system to configure the PCI bus slots instead of using the BIOS. When [Yes] is selected, interrupts may be reassigned by the OS. When a non-PnP OS is installed or you want to prevent reassigning of interrupt settings, select the default setting of [No].
4. BIOS SETUP 4.7 Exit Menu Once you have made all of your selections from the various menus in the Setup program, you should save your changes and exit Setup. Select Exit from the menu bar to display the following menu: 4. BIOS SETUP Exit Menu NOTE: Pressing does not exit this menu. You must select one of the options from this menu or from the legend bar to exit this menu.
4. BIOS SETUP Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When this option is selected or if is pressed, a confirmation is requested. Select [Yes] to load default values. You can now select Exit Saving Changes or make other changes before saving the values to the non-volatile RAM. Discard Changes This option allows you to discard the selections you made and restore the values you previously saved.
5. SOFTWARE SETUP 5.1 ASUS Smart Motherboard Support CD NOTE: The support CD contents are subject to change at any time without notice. To begin using your support CD disc, just insert it into your CD-ROM drive and the support CD installation menu should appear. If the menu does not appear, double click or run E:\ASSETUP.EXE (assuming that your CD-ROM drive is drive E:). 5.1.
5. SOFTWARE SETUP 5.1.2 Support CD Submenus NOTE: The support CD contents are subject to change at any time without notice. Installation Submenu LDCM: Installs software to monitor PC system(s). ASUS Probe: Installs a simple utility to monitor your computer’s fan, temperature, and voltages. ASUS LiveUpdate: Installs a program to help you update your BIOS or download a BIOS image file. Driver: Installs the necessary drivers for your onboard components to work properly.
5. SOFTWARE SETUP PC-cillin 98: Installs Trend’s PC-cillin virus protection software. View the online help for more information. Adobe Acrobat Reader: Installs the Adobe Acrobat Reader software necessary to view user’s manuals saved in PDF format. Updated or other language versions of this motherboard's manual is available in PDF format at any of our web sites. Exit: Returns to the Installation menu.
5. SOFTWARE SETUP 5.2 Operating Systems Although ASUS motherboards passed testing on several operating systems, the operating system shown in these sections will be that of Microsoft’s Windows 98. You should always use the latest operating system and updates when using new hardware to ensure full compliancy. For Windows 95, you must use OSR 2.0 or later. For Windows NT 4.0, you must use Service Pack 3.0 or later. 5.
5. SOFTWARE SETUP 5.3.1 PCI Ethernet Controller Found (2) Click here and then click Next. (1) Click here. (3) Insert your ASUS Support CD, browse to here, and then click Next. (4) Click here. (6) Enter E:\WIN98 here and then click OK. 5. S/W SETUP Windows 98 (5) Insert your Windows 98 CD, and then click here. (8) Click here. (7) Insert your ASUS Support CD, and then click here. (9) Click here.
5. SOFTWARE SETUP 5.4 LDCM Local Setup System Requirements • • • • • • • • Intel® Pentium® microprocessor or higher. Operating system: Microsoft Windows 95 (can be OEM Service Release 2), or Windows 98, or Windows NT 4.0 (Service Pack 4 or later). Microsoft Internet Explorer 4.01 or higher. Memory: 16 MB of RAM for Windows 95/98; 24 MB of RAM for Windows NT (32 MB recommended).
5. SOFTWARE SETUP (5) Click here. (6) Click here. (7) Click here. (10) Click here and then follow the online instruction to finish installing. 5. S/W SETUP Windows 98 (9) Click here. (8) Click here.
5. SOFTWARE SETUP 5.5 LDCM Administrator Setup System Requirements • • • • • • • • Intel® Pentium® microprocessor or higher. Operating system: Microsoft Windows 95 (can be OEM Service Release 2), or Windows 98, or Windows NT 4.0 (Service Pack 4 or later). Microsoft Internet Explorer 4.01 or higher. Memory: 16 MB of RAM for Windows 95/98; 24 MB of RAM for Windows NT (32 MB recommended).
5. SOFTWARE SETUP (5) Click here only after you have carefully read the license agreement. (6) Click here. (8) Click here. (7) Click here. 5. S/W SETUP Windows 98 (9) Click here.
5. SOFTWARE SETUP 5.6 ASUS PC Probe Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. NOTE: ASUS PC Probe will not run if another hardware monitoring utility, such as LDCM, is installed. To uninstall any program, see 5.10 Uninstalling Programs. (1) Click here. (2) Click here. (3) Click here. 5. S/W SETUP Windows 98 (5) Click here. 86 ASUS MEW-L User’s Manual (4) Click here. (6) Click here.
5. SOFTWARE SETUP (7) Click here. (10) Click here. 5. S/W SETUP Windows 98 (9) Click here. (8) Click here.
5. SOFTWARE SETUP 5.7 ASUS LiveUpdate Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. (1) Click here. (2) Click here. 5. S/W SETUP Windows 98 88 (3) Click here. (4) Click here. (5) Click here. (6) Click here.
5. SOFTWARE SETUP 5.8 Drivers 5.8.1 VGA Driver Setup Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. NOTE: Before you install the VGA driver, make sure that the INF Update Utility is installed (see 5.9.1 INF Update Utility for 810 Chipset) (1) Click here. (2) Click here. (4) Click here. (5) Click here. 5. S/W SETUP Windows 98 (3) Click here. (6) Click here. (7) Click here.
5. SOFTWARE SETUP 5.8.2 Audio Driver Setup Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. (1) Click here. (2) Click here. (3) Click here. (4) Click here. (5) Click here and then click OK to install other drivers and software. 5.
5. SOFTWARE SETUP 5.9 Other 5.9.1 INF Update Utility for 810 Chipset NOTE: If you are using Windows 98 SE, you can skip this installation procedure. Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. (1) Click here. (2) Click here. (3) Click here. (5) Click here only after you have read the license agreement. (7) Click here to install the driver to the default folder. 5.
5. SOFTWARE SETUP 5.9.2 Intel Security Driver Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. (1) Click here. (2) Click here. (3) Click here. (4) Click here. 5. S/W SETUP Windows 98 (5) Click here. (7) Click here. 92 (6) Click here. (8) Click here and then follow the online instructions.
5. SOFTWARE SETUP 5.9.3 YAMAHA S-YXG50 Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. (1) Click here. (2) Click here. (3) Click here. (4) Click here. (6) Click here. 5. S/W SETUP Windows 98 (5) Enter the information requested and the click here* . * The serial number can be found on the software license agreement card. (7) Click here only if you accept the terms of the agreement.
5. SOFTWARE SETUP (9) Click here. (10) Click here. (11) Click here. 5.
5. SOFTWARE SETUP 5.9.4 YAMAHA XGStudio Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. (2) Click here. (1) Click here. (4) Click here. (3) Click here. (6) Click here. 5. S/W SETUP Windows 98 (5) Click here only after you have carefully read the license agreement. (7) Click here. (8) Click here. (9) Click here.
5. SOFTWARE SETUP 5.9.5 Microsoft DirectX 6.0 Driver Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. (1) Click here. (3) Click here. (2) Click here. (4) Click here only after you have read the license agreement. (5) Click here. 5. S/W SETUP Windows 98 (6) Click here.
5. SOFTWARE SETUP 5.9.6 PC-cillin 98 Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. (1) Click here. (2) Click here. (4) Click here. (3) Click here. (5) Click here only if you accept the terms of the license agreement. (7) Click here. 5. S/W SETUP Windows 98 (6) Click here. (8) Click here and then follow the online instructins to finish installation.
5. SOFTWARE SETUP 5.9.7 Adobe Acrobat Reader V4.0 Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the setup screen. (2) Click here. (1) Click here. (4) Click here. (3) Click here. (5) Click here only if you accept the terms of the license agreement. 5. S/W SETUP Windows 98 (7) To install other drivers or programs, click here and then click Finish. 98 ASUS MEW-L User’s Manual (6) Click here.
5. SOFTWARE SETUP 5.10 Uninstalling Programs Add/Remove Programs is a basic component within Windows. You may use this function if a program does not provide its own uninstall program. (1) Double-click here to open the Add/Remove Programs Properties dialog box. 5. S/W SETUP Windows 98 (2) Select the program to remove and click here. (3) Click here.
5. SOFTWARE SETUP (This page was intentionally left blank.) 5.
6. SOFTWARE REFERENCE 6. S/W REFERENCE Windows 98 6.1 Display Properties The motherboard’s built-in 2D/3D AGP VGA supports professional graphics design, gaming, learning, and business applications. NOTE: Depending on your system configuration, components, and options, your system may not show all of the settings displayed in the following pictures. To open the Properties dialog box, right-click the desktop and select Properties, the Settings tab, and then the Advanced button.
6. SOFTWARE REFERENCE 6. S/W REFERENCE Windows 98 Monitor Shows what type of monitor you are currently using. To install the software for a new monitor, click Change. Performance Specifies the degree of acceleration you want for your graphics hardware. Full acceleration is the fastest and is recommended for most computers. If your ocmputer is having problems and you suspect graphics acceleration to be the cause, use the highest setting at which you do not have problems.
6. SOFTWARE REFERENCE 6. S/W REFERENCE Windows 98 Information Gives information on your graphics device such as chipset, memory, BIOS, and drivers. Internet links are also available for easy access to the ASUS Web page for new updated drivers and notices. Color (Desktop) Allows you to adjust the quality of your display according to your preference. Gamma correction is available only in 16-bit color and 24-bit color (true color, 16.7M-color) modes.
6. SOFTWARE REFERENCE 6. S/W REFERENCE Windows 98 Color (Video) Lets you make color settings for videos. Adjustment Allows you to adjust the display position, size, and refresh rate. Change refresh rate Allows you to adjust the default refresh rates for each resolution and color settings. Change current refresh rate Allows you to adjust the currently displayed resolution refresh rate. Advanced Allows you to assign hot keys to enable the OnScreen Display (OSD). To use this function, select Enable OSD.
6. SOFTWARE REFERENCE 6. S/W REFERENCE Windows 98 6.2 ASUS PC Probe ASUS PC Probe is a convenient utility to continuously monitor your computer system’s vital components, such as fan rotations, Voltages, and temperatures. It also has a utility that lets you review useful information about your computer, such as hard disk space, memory usage, and CPU type, CPU speed, and internal/external frequencies through the DMI Explorer. 6.2.
6. SOFTWARE REFERENCE 6. S/W REFERENCE Windows 98 6.2.2 Using ASUS PC Probe Monitoring Monitor Summary Shows a summary of the items being monitored. Temperature Monitor Shows the PC’s temperature. Temperature Warning threshold adjustment (Move the slider up to increase the threshold level or down to decrease the threshold level) Fan Monitor Shows the PC’s fan rotation.
6. SOFTWARE REFERENCE 6. S/W REFERENCE Windows 98 Settings Lets you set threshold levels and polling intervals or refresh times of the PC’s temperature, fan rotation, and voltages. CPU Cooling System Setup Lets you select when to enable software CPU cooling. When When CPU Overheated is selected, the CPU cooling system is enabled whenever the CPU temperature reaches the threshold value. History Lets you record the current monitoring activity of a certain component of your PC for future reference.
6. SOFTWARE REFERENCE 6. S/W REFERENCE Windows 98 Memory Shows the PC’s memory load, memory usage, and paging file usage. Device Summary Shows a summary of devices in your PC. DMI Explorer Shows information pertinent to the PC, such as CPU type, CPU speed, and internal/external frequencies, and memory size. Utility Lets you run programs outside of the ASUS Probe modules. To run a program, click Execute Program.
6. SOFTWARE REFERENCE 6. S/W REFERENCE Windows 98 6.2.3 ASUS PC Probe Task Bar Icon Right-clicking the PC Probe icon will bring up a menu to open or exit ASUS PC Probe and pause or resume all system monitoring. When the ASUS PC Probe senses a problem with your PC, portions of the ASUS PC Probe icon changes to red, the PC speaker beeps, and the ASUS PC Probe monitor is displayed.
6. SOFTWARE REFERENCE 6. S/W REFERENCE Windows 98 6.3 ASUS LiveUpdate ASUS LiveUpdate is a utility that allows you to update your motherboard’s BIOS and drivers. The use of this utility requires that you are properly connected to the Internet through an Internet Service Provider (ISP). 1. Start ASUS Update V2.00. Launch the utility from Start | Programs | ASUS Utility | ASUS LiveUpdate V1.00. 2. Select an update method. 3.
6. SOFTWARE REFERENCE 6. S/W REFERENCE Windows 98 6.4 Using Yamaha XGstudio Player To start the Yamaha XGstudio, click Start, point to Programs, point to YAMAHA XGstudio, and then click XGstudio Player. 6.4.1 Yamaha XGstudio Player Control Panel Closes the player. NOTE: You can also close the player by pressing +. Designates the song after the song currently playing as the new current-play song. Minimizes the player to an icon.
6. SOFTWARE REFERENCE 6. S/W REFERENCE Windows 98 6.5 Using Yamaha XGstudio Mixer To start the Yamaha XGstudio, click Start, point to Programs, point to YAMAHA XGstudio, and then click XGstudio Mixer. 6.5.
6. SOFTWARE REFERENCE 6. S/W REFERENCE Windows 98 Smart Arranger The Smart Arranger allows you to easily change the mood of a song. You can switch between seven ensemble voice sets with these buttons. To return to the original voice set, click .
6. SOFTWARE REFERENCE 6. S/W REFERENCE Windows 98 6.6 Hardware Information (1) Click here.
7. APPENDIX 7. APPENDIX ASUS LAN Card 7.1 PCI-L101 Fast Ethernet Card LEDs LAN Activity Output Signal Intel Chipset RJ45 Wake on LAN Output Signal ASUS Motherboard type Other If you are using the ASUS PCI-L101 on an ASUS motherboard, leave the jumper on its defaut setting of “ASUS.” If you are using another brand of motherboard, set the jumper to “Other.” Connect the Wake on LAN (WOL) output signal to the motherboard’s WOL_CON in order to utilize the wake on LAN feature of the motherboard.
7. APPENDIX 7.1.1 Features 7. APPENDIX ASUS LAN Card • • • • • • • • • • • • Intel 82558 Ethernet LAN Controller (Fully integrated 10BASE-T/100BASE-TX) Wake-On-LAN Remote Control Function Supported PCI Bus Master Complies to PCI Local Bus Rev. 2.1 specifications Consists of MAC & PHY (10/100Mbps) interfaces Complies to IEEE 802.3 10BASE-T and IEEE 802.3u 100BASE-TX interfaces Fully supports 10BASE-T & 100BASE-TX operations through a single RJ45 port Supports 32-bit Bus Master Technology / PCI Rev. 2.
7. APPENDIX 7.2 S370 Series CPU Cards 7. APPENDIX S370 Series CPU Cards The optional ASUS S370 Series CPU Cards allow Slot 1 motherboards to accept socket 370 processors. The ASUS S370 Series CPU Cards give Slot 1 motherboard owners an inexpensive way to upgrade their Pentium II computers using lower costing socket 370 processors. Since socket 370 processors are based on the Pentium II design, the only difference is the connector and the amount of internal cache within the processor.
7. APPENDIX 7.2.1 Using the ASUS S370 Series CPU Card The general procedure for using the ASUS S370 Series CPU Card is as follows: 7. APPENDIX S370 Series CPU Cards 1. Check the voltage setting for your socket 370 processor using the jumpers on the card if necessary. For current socket 370 processors, the default setting should be used. See the reverse side of the ASUS S370 Series CPU Card or this page for voltage settings. 2. Install the socket 370 processor.
7. APPENDIX 7.3 Modem Riser 7.3.1 56K Software Modem 7.3.2 Primary/Seconday MR There are two types of modem risers: primary MR and secondary MR. In appearance, the primary MR has a crystal onboard but the secondary does not. If your motherboard has an audio codec and no PCI audio chipset onboard, you may use the secondary MR; otherwise, you should use the primary MR. Layout of Primary MR Top: 7.
7. APPENDIX 7.3.4 Software Setup in Windows 98 The Modem Riser supports the Plug and Play feature. It allows your computer to automatically set the optimal configurations for the MR and communication software. Follow the procedure below to install the modem driver. 1. Power ON the computer after the hardware installation is completed. 7. APPENDIX Modem Riser 2. Windows 98 will automatically detect the modem and display a “PCI Card” message under “Add New Hardware Found”. 3.
INDEX Symbols 16-bit I/O Recovery Time 61 8-bit I/O Recovery Time 61 A AC PWR Loss Restart 70 Adobe Acrobat Reader 99 AFLASH.
INDEX Driver Setup Audio 90 Intel Security 93 Microsoft DirectX 96 PCI Audio 81 VGA 89 E ECP DMA Select 63 Ethernet Card 115 Exit Discarding Changes 75 Exit Saving Changes 75 Expansion Card Installation Procedure 27 Expansion Cards Assigning IRQs 28 Audio Modem Riser 30 External Connectors 31 F J Joystick/MIDI Connector 33 JumperFree™ Mode Setting 18 K Keyboard Lock Switch Lead 43 Fast-Ethernet Port Connector 33 Flash Memory Writer Utility 46 Floppy 3 Mode Support 52 Floppy Disk Access Control 62 Flopp
INDEX Memory Hole At 15M-16M 61 Message LED Lead 43 Microsoft DirectX 96 Modem Riser 119 Monitor Output Connector 33 Motherboard Layout 14 Part Locations 13 Settings 17 Multi-Sector Transfers 55 O ONB VGA BIOS First 65 Onboard AC97 Modem Controller 62 Onboard Audio Controller 62 Onboard Audio Setting 19 Onboard CIR I/O 63 Onboard CIR IRQ 63 Onboard FDC Swap A & B 62 Onboard Game Port 63 Onboard ISA Bridge 61 Onboard LAN Power Setting 20 Onboard LAN Setting 20 Onboard MIDI I/O 63 Onboard MIDI IRQ 63 Onboard
INDEX Serial Port Connector 32 Serial Port Header 38 Settings Automatic Timeout Reboot 21 CPU Frequency 22 I/O Voltage 19 JumperFree™ Mode 18 Onboard Audio 19 Onboard LAN 20 Onboard LAN Power 20 Safe Mode 21 Slot 1/5 IRQ 64 Slot 2 IRQ 64 Slot 3/6 IRQ 64 Slot 4 IRQ 64 SMART Monitoring 55 SMBus Connector 39 Software Setup Adobe Acrobat Reader 99 LDCM Administrator 84 LDCM Client 82 LiveUpdate 88 PC Probe 87 PC-cillin 98 97 Yamaha S-YXG50 92 Yamaha XGStudio 94 Specifications 8 Supervisor Password 56 Support CD
® Goes Mobile! M8300/8200 Series Thin & Light Convertible Notebook PC 13.3” or 12.1” TFT Color Display 233/266/300/333/366/400+MHz F7400 Series Professional Notebook PC 14.1” TFT Color Display 300/333/366/400+MHz Built-in DVD/MPEG2 Decoder L7300/7200 Series All-in-One Compact Notebook PC 13.3” or 12.
® Ultra-Fast CD-ROM • • • • • Drive Interface Type: Disc Formats: Disk Size: OS Compatibility: Cache Buffer Size: Data Transfer Rate: Access Time: Supports high speed CD-Audio playback Supports high speed digital audio extraction Supports UltraDMA/33 transfer mode Compatible with all CD formats Supports multi-read function (CD-R/CD-RW) ATAPI/Enhanced IDE supporting PIO mode 4, multiword DMA mode 2, UltraDMA/33 Audio CD, CD-ROM (mode 1 & mode 2), Mixed mode, CD-ROM/XA (mode 2, form 1 & form 2), Video C
® Barebone Servers Pentium® III PC100 ECC Ultra2 SCSI 5.25” Pentium® II Max. Memory Onboard Fixed Storage Support (GB) (Channels) Devices Hot-Swap Trays AP100 1 1 1 3 0 AP200 2 1 1 3 0 AP2000 2 1 1 4 3 or 5* AP2500 2 1 1 4 3 or 5* AP3000 2 Xeon™ 2 2 4 3 or 5* AP6000 2 1 1 4 8** AP7500 2 1 1 4 8** AP8000 2 Xeon™ 2 2 4 8** * ** Three 1.6-inch or five 1-inch SCA-2 SCSI hard drives Eight 1.
ASUS AR1000 RAID Sub-system with DA3000 SCSI-to-SCSI RAID Controller • • • • • • • • • • • • • • • • Supports 5x86 RAID processor and two 72-pin SIMM sockets for up to 128MB cache memory Supports three Ultra2 SCSI channels; up to 80MB/sec data transfer rate Supports multiple Host/Drive channel capacity Redundant controller capacity Supports non-RAID, RAID levels 0, 1, 0+1, 3, 5 On-line failure drive rebuilding Automatic rebuilding — supports local/global spare drive On-line expansion capacity Supports SAF-