User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- 2.1 Chassis cover
- 2.2 Air duct
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.5.1 Installing an E1.S module (optional)
- 2.5.2 Removing an E1.S module (optional)
- 2.5.3 Installing an external 2.5” storage device (on selected models)
- 2.5.4 Removing an external 2.5” storage device (on selected models)
- 2.5.5 Installing an internal 2.5” storage device (optional on selected models)
- 2.5.6 Removing an internal 2.5” storage device (optional on selected models)
- 2.6 Expansion slot
- 2.7 Cable connections
- 2.8 Removable/optional components
- 2.9 Rail Kit Options
- Chapter 3: Motherboard Information
- Chapter 4: BIOS Setup
- 4.1 Managing and updating your BIOS
- 4.2 BIOS setup program
- 4.3 Main menu
- 4.4 Performance Tuning menu
- 4.5 Advanced menu
- 4.5.1 Trusted Computing
- 4.5.2 ACPI Settings
- 4.5.3 Redfish Host Interface Settings
- 4.5.4 Onboard LAN Configuration
- 4.5.5 UEFI Variables Protection
- 4.5.6 Serial Port Console Redirection
- 4.5.7 SIO Configuration
- 4.5.8 PCI Subsystem Settings
- 4.5.9 USB Configuration
- 4.5.10` Network Stack Configuration
- 4.5.11 NVMe Configuration
- 4.5.12 APM Configuration
- 4.5.13 Tls Auth Configuration
- 4.5.14 Intel(R) Virtual RAID on CPU
- 4.5.15 Third-party UEFI driver configurations
- 4.6 Platform Configuration menu
- 4.7 Socket Configuration menu
- 4.8 Security menu
- 4.9 Boot menu
- 4.10 Tool menu
- 4.11 Event Logs menu
- 4.12 Server Mgmt menu
- 4.13 Exit menu
- Appendix
4-37
The following item appears only when AVX P1 is set to [Nominal].
Dynamic SST-PP [Disable]
Enabling Dynamic SST-PP supports dynamic SST-PP selection.
Configuration options: [Disable] [Enable]
HWP Native Mode is a prerequisite for enabling Dynamic SST-PP.
SpeedStep (Pstates) [Enable]
Allows you to enable or disable EIST (P-States).
Configuration options: [Disable] [Enable]
Boot performance mode [Max Performance]
Allows you to select the performance state that the BIOS will set before OS
hand off.
Configuration options: [Max Performance] [Max Efficient] [Set by Intel Node
Manager]
Energy Efficient Turbo [Enable]
Allows you to enable or disable Energy Efficient Turbo, MSR 0x1FC [19].
Configuration options: [Disable] [Enable]
The following item appears only when SpeedStep (Pstates) is set to [Enable].
Turbo Mode [Enable]
Allows you to enable or disable processor Turbo Mode (requires EMTTM
enabled too).
Configuration options: [Disable] [Enable]
Hardware PM State Control
Hardware P-States [Native Mode]
Allows you to switch between Hardware P-States mode.
[Disable]
Hardware chooses a P-state based on OS Request (Legacy
P-States).
[Native Mode] Hardware chooses a P-state based on OS guidance.
[Out of Band Mode] Hardware autonomously chooses a P-state (no OS guidance).
[Native Mode with no Legacy Support] Hardware chooses a P-state based on OS
guidance (without Legacy support).
Frequency Prioritization
SST-CP [Enable]
Allows you to enable or disable SST-CP. When enabled, per core power budgeting is
activated.
Configuration options: [Enable] [Disable]
HWP Native Mode is a prerequisite for enabling SST-CP.