User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- Chapter 3: Installation Options
- Chapter 4: BIOS Setup
- 4.1 Managing and updating your BIOS
- 4.2 BIOS setup program
- 4.3 Main menu
- 4.4 Performance Tuning menu
- 4.5 Advanced menu
- 4.5.2 Trusted Computing
- 4.5.2 PSP Firmware Versions
- 4.5.3 Redfish Host Interface Settings
- 4.5.4 AMD CBS
- 4.5.5 APM Configuration
- 5.5.6 Onboard LAN Configuration
- 4.5.7 Serial Port Console Redirection
- 4.5.8 CPU Configuration
- 4.5.9 PCI Subsystem Settings
- 4.5.10 USB Configuration
- 4.5.11 Network Stack Configuration
- 4.5.12 CSM Configuration
- 4.5.13 NVMe Configuration
- 4.5.14 AMD Mem Configuration Status
- 4.5.15 Third-party UEFI driver configurations
- 4.6 Chipset menu
- 4.7 Security menu
- 4.8 Boot menu
- 4.9 Tool menu
- 4.10 Event Logs menu
- 4.11 Server Mgmt menu
- 4.12 Exit menu
- Chapter 5: Driver Installation
- Appendix
4-26
Chapter 4: BIOS Setup
Cs0dtDrvStren [Auto]
Configuration options: [Auto] [120.0 Ohm] [60.0 Ohm] [40.0 Ohm] [30.0
Ohm] [24.0 Ohm] [20.0 Ohm]
CkeDrvStren [Auto]
Configuration options: [Auto] [120.0 Ohm] [60.0 Ohm] [40.0 Ohm] [30.0
Ohm] [24.0 Ohm] [20.0 Ohm]
Data Bus Configuration
Data Bus Configuration User Controls [Auto]
Allows you to specify the mode for drive strength.
Configuration options: [Auto] [Manual]
The following items appear only when Data Bus Configuration User Controls is set to
[Manual].
RttNom [Auto]
Configuration options: [Rtt_Nom Disable] [RZQ/4] [RZQ/2] [RZQ/6]
[RZQ/1] [RZQ/5] [RZQ/3] [RZQ/7] [Auto]
RttWr [Auto]
Configuration options: [Dynamic ODT Off] [RZQ/2] [RZQ/1] [Hi-Z]
[RZQ/3] [Auto]
RttPark [Auto]
Configuration options: [Rtt_PARK Disable] [RZQ/4] [RZQ/2] [RZQ/6]
[RZQ/1] [RZQ/5] [RZQ/3] [RZQ/7] [Auto]
Common RAS
Data Poisoning [Auto]
Configuration options: [Enabled] [Disabled] [Auto]
DRAM Post Package Repair [Disable]
Allows you to enable or disable DRAM POST Package Repair.
Configuration options: [Enable] [Disable]
RCD Parity [Auto]
Configuration options: [Enabled] [Disabled] [Auto]
DRAM Address Command Parity Retry [Auto]
Configuration options: [Enabled] [Disabled] [Auto]
The following item appears only when DRAM Address Command Parity Retry is set to
[Enabled].
Max Parity Error Replay [8]
The values in hex, 1, 2, or 3 is invalid.
Configuration options: [0] - [39]
Write CRC Enable [Auto]
Configuration options: [Enabled] [Disabled] [Auto]
DRAM Write CRC Enable and Retry Limit [Auto]
Configuration options: [Enabled] [Disabled] [Auto]