User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Central Processing Unit (CPU)
- 2.3 System memory
- 2.4 Storage devices
- 2.5 Expansion slots
- 2.5.1 The PCI Express riser card
- 2.5.2 Installing an ASUS PIKE II card
- 2.5.3 Reconnecting the cable to the M.2 expansion board (only for SKU-3)
- 2.5.4 Installing an M.2 (NGFF) card
- 2.5.5 Reconnecting the cable to the OCP 3.0 slot baseboard (only for SKU-2)
- 2.5.6 (optional) Installing the PFR module
- 2.5.7 Configuring an expansion card
- 2.6 Cable connections
- 2.7 SATA/SAS backplane cabling
- 2.8 Removable/optional components
- Chapter 3: Installation Options
- Chapter 4: Motherboard Infomation
- Chapter 5: BIOS Setup
- 5.1 Managing and updating your BIOS
- 5.2 BIOS setup program
- 5.3 Main menu
- 5.4 Advanced menu
- 5.4.1 OffBoard SATA Controller Configuration
- 5.4.2 Trusted Computing
- 5.4.3 ACPI Settings
- 5.4.4 Redfish Host Interface Settings
- 5.4.5 Onboard LAN Configuration
- 5.4.6 Serial Port Console Redirection
- 5.4.7 SIO Common Setting
- 5.4.8 SIO Configuration
- 5.4.9 PCI Subsystem Settings
- 5.4.10 USB Configuration
- 5.4.11 Network Stack Configuration
- 5.4.12 CSM (Compatibility Support Module)
- 5.4.13 NVMe Configuration
- 5.4.14 APM Configuration
- 5.4.15 Third-party UEFI driver configurations
- 5.5 Platform Configuration menu
- 5.6 Socket Configuration menu
- 5.7 Event Logs menu
- 5.8 Server Mgmt menu
- 5.9 Security menu
- 5.10 Boot menu
- 5.11 Tool menu
- 5.12 Save & Exit menu
- Chapter 6: Driver Installation
- Appendix
5-54
Chapter 5: BIOS Setup
CPU C State Control
Enable Monitor MWAIT [Enable]
Allows you to enable or disable Monitor and MWAIT instructions.
Configuration options: [Disable] [Enable]
CPU C1 auto demotion [Enable]
Allows CPU to automatically demote to C1. Takes effect after reboot.
Configuration options: [Disable] [Enable]
CPU C1 auto undemotion [Enable]
Allows CPU to automatically undemote from C1. Takes effect after reboot.
Configuration options: [Disable] [Enable]
CPU C6 Report [Auto]
Allows you to enable or disable CPU C6 (ACPI C3) report to OS.
Configuration options: [Disable] [Enable] [Auto]
Enhanced Halt State (C1E) [Enable]
Core C1E auto promotion Control. Takes effect after reboot.
Configuration options: [Disable] [Enable]
OS ACPI Cx [ACPI C2]
Allows you to select to report CC3/CC6 to OS ACPI C2 or ACPI C3.
Configuration options: [ACPI C2] [ACPI C3]
Package C State Control
Package C State [Auto]
Allows you to select Package C State limit.
Configuration options: [C0/C1 state] [C2 state] [C6(non Retention state] [Auto]
Register Access Low Latency Mode [Disabled]
Enable low latency mode for register accesses.
Configuration options: [Disabled] [Enabled]
Enabling this mode will prevent PkgC6 as register access fabric is prevented from going to
idle.
CPU Thermal Management
CPU T State Control
Software Controlled T-States [Disabled]
Allows you to enable or disable Software Controlled T-States.
Configuration options: [Disabled] [Enabled]
The following item appears only when
Software Controlled T-States
is set to
[Enabled]
.
T-State Throttle Level [Disable]
On-Die Thermal Throttling.
Configuration options: [Disabled] [6.25%] [12.5%][18.75%][25.0%][31.25%]
[37.5%][43.75%][50.0%][56.25%][62.5%][68.75%][75.0%] [81.25%][87.5%]
[93.75%]