User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- 2.1 Chassis cover
- 2.2 Central Processing Unit (CPU)
- 2.3 System memory
- 2.4 Storage devices
- 2.5 Expansion slots
- 2.5.1 The PCI Express riser card
- 2.5.2 Installing an ASUS PIKE II card
- 2.5.3 Reconnecting the cable to the M.2 expansion board (only for SKU-3)
- 2.5.4 Installing an M.2 (NGFF) card
- 2.5.5 Reconnecting the cable to the OCP 3.0 slot baseboard (only for SKU-2)
- 2.5.6 (optional) Installing the PFR module
- 2.5.7 Configuring an expansion card
- 2.6 Cable connections
- 2.7 SATA/SAS backplane cabling
- 2.8 Removable/optional components
- 2.9 Rail Kit Options
- Chapter 3: Motherboard Infomation
- Chapter 4: BIOS Setup
- 4.1 Managing and updating your BIOS
- 4.2 BIOS setup program
- 4.3 Main menu
- 4.4 Advanced menu
- 4.4.1 OffBoard SATA Controller Configuration
- 4.4.2 Trusted Computing
- 4.4.3 ACPI Settings
- 4.4.4 Redfish Host Interface Settings
- 4.4.5 Onboard LAN Configuration
- 4.4.6 Serial Port Console Redirection
- 4.4.7 SIO Common Setting
- 4.4.8 SIO Configuration
- 4.4.9 PCI Subsystem Settings
- 4.4.10 USB Configuration
- 4.4.11 Network Stack Configuration
- 4.4.12 CSM (Compatibility Support Module)
- 4.4.13 NVMe Configuration
- 4.4.14 APM Configuration
- 4.4.15 Third-party UEFI driver configurations
- 4.5 Platform Configuration menu
- 4.6 Socket Configuration menu
- 4.7 Event Logs menu
- 4.8 Server Mgmt menu
- 4.9 Security menu
- 4.10 Boot menu
- 4.11 Tool menu
- 4.12 Save & Exit menu
- Chapter 5: Driver Installation
- Appendix
4-21
ASUS ESC4000-E10S
Boot from Storage Devices [UEFI only]
Allows you to select the type of storage devices to run first during the system boot. It
is recommended to select either
[Legacy only]
or
[UEFI only]
according to devices
specification for better stability. Selecting
[Ignore]
will accelerate the boot up time
without running network devices during POST (Power-On Self-Test).
Configuration options: [Ignore] [UEFI only] [Legacy only]
Launch Video OPROM policy [UEFI only]
This option controls the execution of UEFI and Legacy Video OPROM.
Configuration options: [Ignore] [UEFI only] [Legacy only]
Boot from PCI-E/PCI Expansion Devices [UEFI only]
Allows you to select the type of PCI-E/PCI Expansion devices to run first during the
system boot.
Configuration options: [Ignore] [UEFI only] [Legacy only]
Device
The devices and names shown in the NVMe configuration list depends on the connected
devices. If no devices are connected,
No NVMe Device Found
will be displayed.
Self Test Option [Short]
This option allows you to select either Short or Extended Self Test. Short option will
take couple of minutes, and the extended option will take several minutes to complete.
Configuration options: [Short] [Extended]
Self Test Action [Controller Only Test]
This item allows you to select either to test Controller alone or Controller and
NameSpace. Selecting Controller and Namespace option will take a lot longer to
complete the test.
Configuration options: [Controller Only Test] [Controller and NameSpace Test]
Run Device Self Test
Press <Enter> to perform device self test for the corresponding Option and Action
selected by the user. Pressing the <ESC> key will abort the test. The results shown
below is the most recent result logged in the device.
4.4.13 NVMe Configuration
This page will display the NVMe controller and drive information.