User Manual
Table Of Contents
- 目錄
- 使用注意事項
- 用電安全
- 關於本使用手冊
- 第一章:系統導覽
- 第二章:硬體安裝
- 第三章:主機板資訊
- 第四章:BIOS 程式設定
- 4.1 管理、更新您的 BIOS 程式
- 4.2 BIOS 程式設定
- 4.3 主選單(Main)
- 4.4 效能調整選單(Performance Tuning menu)
- 4.5 進階選單(Advanced menu)
- 4.5.1 可信任計算(Trusted Computing)
- 4.5.2 AMD CBS
- 4.5.3 內建網路設置(Onboard LAN Configuration)
- 4.5.4 序列埠控制台重新導向(Serial Port Console Redirection)
- 4.5.5 CPU 設定(CPU Configuration)
- 4.5.6 PCI 子系統設定(PCI Subsystem Settings)
- 4.5.7 USB 設定(USB Configuration)
- 4.5.8 網路協定堆疊設定(Network Stack Configuration)
- 4.5.9 NVMe 設定(NVMe Configuration)
- 4.5.10 SATA 設定(SATA Configuration)
- 4.5.11 APM 設定(APM Configuration)
- 4.5.12 AMD 記憶體設定狀態(AMD Mem Configuration Status)
- 4.5.13 T1s Auth
- 4.5.14 驅動程式狀態(Driver Health)
- 4.6 晶片選單(Chipset menu)
- 4.7 安全性選單(Security menu)
- 4.8 開機選單(Boot menu)
- 4.9 工具選單(Tool menu)
- 4.10 事件記錄選單(Event Logs menu)
- 4.11 伺服器管理選單(Server Mgmt menu)
- 4.12 離開 BIOS 程式(Exit menu)
- 第五章:安裝驅動程式
- 附錄
第四章:BIOS 程式設定
4-20
Redirection After BIOS POST [Always Enable]
當 Bootloader 已被選擇超過傳統控制台轉向,則允許您設定本項。設定值有:
[Always Enable] [BootLoader]
Serial Port for Out-of-Band Management/Windows Emergency Management
Services (EMS)
Console Redirection EMS [Disabled]
啟用或關閉控制台重新導向功能。設定值有:[Disabled] [Enabled]
以下項目只有在 Console Redirection EMS 設為 [Enabled] 時才會出現。
Console Redirection Settings
Out-of-Band Mgmt Port [COM1]
經由序列埠來遠端遙控管理 Windows Server 系統。設定值有:[COM1] [COM2]
Terminal Type EMS [VT-UTF8]
經由序列埠來遠端遙控管理 Windows Server 系統。設定值有:[VT100]
[VT100Plus] [VT-UTF8] [ANSI]
Bits per second EMS [115200]
經由序列埠來遠端遙控管理 Windows Server 系統。設定值有:[9600] [19200]
[57600] [115200]
Flow Control EMS [None]
經由序列埠來遠端遙控管理 Windows Server 系統。設定值有:[None]
[Hardware RTS/CTS] [Software Xon/Xoff]
4.5.5 CPU 設定(CPU Configuration)