User Manual

華碩 ESC4000A-E12 使用手冊
1-15
(下頁繼續)
ACTION PHASE POST CODE TYPE DESCRIPTION
PSP Boot
PSP Boot Loader
phase (Status Post
Codes)
0xBB error BIOS load process fully complete
0xBC error Bootloader successfully release x86
0xBD error Early Secure Debug completed
0xBE error GetFWVersion command received from BIOS is completed
0xBF error SMIInfo command received from BIOS is completed
0xC0
error Successfully entered WarmBootResume()
0xC1 error Successfully copied SecureOS image to SRAM
0xC2 error
Successfully copied trustlets to PSP Secure Memory
0xC3 error About to jump to Secure OS (SBL about to copy and jump)
0xC4
error Successfully restored CCP and UMC state on S3 resume
0xC5 error PSP SRAM HMAC validated by Mini BL
0xC6 error About to jump to <t-base in Mini BL
0xC7 error VMG ECDH unit test started
0xC8 error VMG ECDH unit test passed
0xC9
error VMG ECC CDH primitive unit test started
0xCA error VMG ECC CDH primitive unit test passed
0xCB error
VMG SP800-108 KDF-CTR HMAC unit test started
0xCC error VMG SP800-108 KDF-CTR HMAC unit test passed
0xCD error VMG LAUNCH_* test started
0xCE error VMG LAUNCH_* test passed
0xCF error MP1 has been taken out of reset, and executing SMUFW
0xD0 error PSP and SMU Reserved Addresses correct
0xD1 error Reached Naples steady-state WFI loop
0xD2 error Knoll device successfully initialized
0xD3 error 32-byte RandOut successfully returned from Knoll
0xD4 error 32-byte MAC successfully received from Knoll.
0xD5 error Knoll device verified successfully
0xD6 error CNLI Keys generated and programmed
0xD7 error Enter recovery mode due to trustlet validation fail.
0xD8 error Enter recovery mode due to OS validation fail.
0xD9 error Enter recovery mode due to OEM public key not found.
0xDA error Enter recovery mode with header corruption
0xDB error We should not treat this error as blocking
0xDC error When same fw image type is already loaded in SRAM
0xDD error 0xE2 progress codes are available
0xE0 error Unlock return
0xE2 error Token expiration reset triggered
0xE3 error Completed DXIO PHY SRAM FW key Validation step
0xE4 error MP1 firmware load to SRAM success
0xE5 error Bootloader read the MP1 SRAM successfully
0xE6 error Bootloader successfully reset MP1
0xE7 error DF init successfully done (in absence of AGESA)
0xE8 error UMC init successfully done (in absence of AGESA)
0xE9 error LX6 Boot ROM code ready
0xEA error Bootloader successfully asserted LX6 reset
0xEB error LX6 load to SRAM success
0xEC error Bootloader successfully set LX6 reset vector to SRAM
0xED error Bootloader successfully de-asserted LX6 reset
0xEE error LX6 firmware is running and ready
0xEF error Loading of S3 image done successfully
0xF0 error Bootloader successfully verify signed image using 4K/2K key
0xF1 error Bootloader identified as running on SP52P or multi-socket boot
0xF2 error Security Policy check successful (only in secure boot)
0xF3 error Bootloader successfully loaded SS3
0xF4 error Bootloader successfully load fTPM Driver
0xF5 error Bootloader successfully loaded sys_drv
0xF6 error Bootloader successfully loaded secure OS
0xF7 error Bootloader about to transfer control to secureOS
0xFF error Bootloader sequence finished
Quick VGA
PEI(Pre-EFI
Initialization) phase
0x10 Progress PEI Core Entry
0x11 Progress PEI cache as ram CPU initial
0x15 Progress NB Initialization before installed memory
0x19 Progress SB Initialization before installed memory