User Guide
Table Of Contents
- Notices
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- Chapter 3: Installation options
- Chapter 4: Motherboard Info
- Chapter 5: BIOS setup
- 5.1 Managing and updating your BIOS
- 5.2 BIOS setup program
- 5.3 Main menu
- 5.4 Advanced menu
- 5.4.1 ACPI Settings
- 5.4.2 Smart Settings
- 5.4.3 NCT6779D Super IO Configuration
- 5.4.4 Onboard LAN I210 Configuration
- 5.4.5 Serial Port Console Redirection
- 5.4.6 APM
- 5.4.7 Advanced Power Management Configuration
- 5.4.8 PCI Subsystem Settings
- 5.4.9 Network Stack Configuration
- 5.4.10 CSM Configuration
- 5.4.11 Trusted Computing
- 5.4.12 USB Configuration
- 5.4.13 iSCSI Configuration
- 5.5 IntelRCSetup menu
- 5.5.1 Processor Configuration
- 5.5.2 Advanced Power Management Configuration
- 5.5.3 Common RefCode Configuration
- 5.5.4 QPI Configuration
- 5.5.5 Memory Configuration
- 5.5.6 IIO Configuration
- 5.5.7 PCH Configuration
- 5.5.8 Miscellaneous Configuration
- 5.5.9 Server ME Configuration
- 5.5.10 Runtime Error Logging Support
- 5.6 Server Mgmt menu
- 5.7 Event Logs menu
- 5.8 Monitor menu
- 5.9 Security menu
- 5.10 Boot menu
- 5.11 Tool menu
- 5.12 Exit menu
- Chapter 6: RAID Configuration
- Chapter 7: Driver installation
- 7.1 RAID driver installation
- 7.2 Management applications and utilities installation
- 7.3 Running the Support DVD
- 7.4 Intel® chipset device software installation
- 7.5 Installing the Intel® I210 Gigabit Adapters driver
- 7.6 VGA driver installation
- 7.7 Intel® Rapid Storage Technology enterprise 4.1 installation
- Appendix
viii
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
The use of shielded cables for connection of the monitor to the graphics card is required
to assure compliance with FCC regulations. Changes or modications to this unit not
expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.
Compliance Statement of Innovation, Science and Economic
Development Canada (ISED)
This device complies with Innovation, Science and Economic Development Canada licence
exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
CAN ICES-3(A)/NMB-3(A)
Déclaration de conformité de Innovation, Sciences et
Développement économique Canada (ISED)
Le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
CAN ICES-3(A)/NMB-3(A)