User Manual

Chapter 2: Hardware Setup
2-8
8. Reinstall the air duct. For more information, see the section
Air Duct
.
1
2
3 4
6. Twist each of the four (4) screws with a screwdriver just enough to attach the cooler to
the motherboard. When the four (4) screws are attached, tighten them one by one in a
diagonal sequence to completely secure the cooler.
The cooler screws are T30 models. A torque value of 12 inch-lbf is recommended.
Z11PG-D24
Intel
®
C621
Super
I/O
LCMXO2
1200UHC
BUZZ1
ASPEED
AST2500
Lithium Cell
CMOS Power
DDR4 DIMM_F1 (64bit, 288-pin module) DDR4 DIMM_F2 (64bit, 288-pin module)
DDR4 DIMM_E1 (64bit, 288-pin module) DDR4 DIMM_E2 (64bit, 288-pin module)
DDR4 DIMM_D1 (64bit, 288-pin module) DDR4 DIMM_D2 (64bit, 288-pin module)
DDR4 DIMM_A2 (64bit, 288-pin module) DDR4 DIMM_A1 (64bit, 288-pin module) DDR4 DIMM_B2 (64bit, 288-pin module) DDR4 DIMM_B1 (64bit, 288-pin module)
DDR4 DIMM_C2 (64bit, 288-pin module) DDR4 DIMM_C1 (64bit, 288-pin module)
DDR4 DIMM_M1 (64bit, 288-pin module) DDR4 DIMM_M2 (64bit, 288-pin module)
DDR4 DIMM_L1 (64bit, 288-pin module) DDR4 DIMM_L2 (64bit, 288-pin module)
DDR4 DIMM_K1 (64bit, 288-pin module) DDR4 DIMM_K2 (64bit, 288-pin module)
DDR4 DIMM_G2 (64bit, 288-pin module) DDR4 DIMM_G1 (64bit, 288-pin module)
DDR4 DIMM_H2 (64bit, 288-pin module) DDR4 DIMM_H1 (64bit, 288-pin module)
DDR4 DIMM_J2 (64bit, 288-pin module) DDR4 DIMM_J1 (64bit, 288-pin module)
SYS_FAN1
CPU_FRNTFAN1
CPU_FRNTFAN2
PCIE11
SYS_FAN5
SYS_FAN2
SYS_FAN4
SYS_FAN6
SYS_FAN3
DM_LAN1
CPU1 CPU2
BPPWR1
HDLED1
ISATA2 ISATA1
REARIO1
MSD1
PANEL1
AUX_PANEL1
PWR1
PWR2
PSUSMB1
INTRUSION1
BMCLED1
CATERR1
SBPWR1
VGA_HDR1
IPMI_SW1
SMBUS1
PCH_MFG1
BMC_EN1
DIMMTRIP2
VGA_SW1
LAN_PWR1
DM_IP_SEL1
SMART_PSU1
ME_RCVR1
ICS
ICS
DIMMTRIP1
GPU_FAN6
GPU_FAN7
GPU_FAN2
GPU_FAN1
SLMPCIE5
SLMPCIE1
SLMPCIE6
SLMPCIE9
SLMPCIE23
SLMPCIE10 SLMPCIE21SLMPCIE22
SLMPCIE2
GPU_FAN8
GPU_FAN3
GPU_FAN9
OCUPCIE13
OCULAN1
OCUUSB1
TPM1
OCUPCIE14
GPU_FAN4
GPU_FAN10
GPU_FAN5
PWR_CON2
PWR_M2
CLRTC1
AUX_PANEL2COM1
VROC_KEY1
VPP_I2C1
OMNIP1
OMNIP2
7. Connect the FAN cable from the cooler to the CPU_FRNTFAN1 (CPU_FRNTFAN2 for
the second cooler) connector on the motherboard.
CPU_FRNTFAN1 connector
CPU_FRNTFAN2 connector