User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Setup
- Chapter 3: Motherboard Information
- Chapter 4: BIOS Setup
- 4.1 Knowing BIOS
- 4.2 BIOS setup program
- 4.3 My Favorites
- 4.4 Main menu
- 4.5 Ai Tweaker menu
- 4.6 Advanced menu
- 4.6.1 Platform Misc Configuration
- 4.6.2 CPU Configuration
- 4.6.3 System Agent (SA) Configuration
- 4.6.4 PCH Configuration
- 4.6.5 PCH Storage Configuration
- 4.6.6 PCH-FW Configuration
- 4.6.7 AMT Configuration
- 4.6.8 Thunderbolt(TM) Configuration
- 4.6.9 Serial Port Console Redirection
- 4.6.10 Intel TXT Information
- 4.6.11 PCI Subsystem Settings
- 4.6.12 USB Configuration
- 4.6.13 Network Stack Configuration
- 4.6.14 NVMe Configuration
- 4.6.15 HDD/SSD SMART Information
- 4.6.16 APM Configuration
- 4.6.17 Onboard Devices Configuration
- 4.6.18 Intel(R) Rapid Storage Technology
- 4.7 Monitor menu
- 4.8 Boot menu
- 4.9 Tool menu
- 4.10 Exit menu
- 4.11 Updating BIOS
- Chapter 5: RAID Configuration
- Appendix
ASUS E500 G9
A-7
Notices
FCC Compliance Information
Responsible Party: Asus Computer International
Address: 48720 Kato Rd., Fremont, CA 94538, USA
Phone / Fax No: (510)739-3777 / (510)608-4555
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20cm may be maintained between the antenna and users. The nal end
product must be labeled in a visible area with the following: "Contains FCC ID: PD9AX210NG”
and "Contains IC: 1000M-AX210NG".
This radio transmitter FCCID: PD9AX210NG has been approved by FCC to operate with
the antenna types listed below with the maximum permissible gain and required antenna
impedance for each antenna type indicated. Antenna types not included in this list, having a
gain greater than the maximum gain indicated for that type, are strictly prohibited for use with
this device.
Antenna List:
No. Manufacturer Part No. Antenna Type Peak Gain
1 Inpaq DAM-I3-H1-M2-800-10-66 Dipole antenna 2.73dBi for 2.4GHz
1.79dBi for 5GHz
NOTE:
The antenna connector is Reverse SMA type.