主板針腳說明 C11133 第二版 2016 年 7 月
目錄 主板針腳說明 1-2 1 連接排針..................................................................................................................... 1-3 2 跳線選擇區................................................................................................................ 1-4 3 內部連接端口........................................................................................................... 1-6 4 內置 LED 指示燈..................................................................................................
1 連接排針 1. CMOS 配置數據清除(2-pin CLRTC) 想要清除這些數據,可以依照下列步驟進行: CLRTC +3V_BAT GND 在主板上的 CMOS 存儲器中記載著正確的時間與系統硬件配置等數 據,這些數據並不會因電腦電源的關閉而丟失數據與時間的正確性, 因為這個 CMOS 的電源是由主板上的鋰電池所供應。 PIN 1 1. 關閉電腦電源,拔掉電源線; 2. 用一個金屬物體,如螺絲刀,將 CLRTC 跳線的兩個針腳短路。 3. 插上電源線,開啟電腦電源; 4. 當開機步驟正在進行時按著鍵盤上的 <Del> 鍵進入 BIOS 程式畫面重新設 定 BIOS 數據。 • 如果上述步驟不起作用,移除電池並再次將兩個針腳短路以清除 CMOS RTC RAM 數據。CMOS 清除完畢後,重新安裝電池。 • 如果您是因為超頻的緣故導致系統無法正常開機,您無須使用上述的 配置數據清除方式來排除問題。建議可以採用 C.P.R(CPU 超不死) 功能,只要將系統重新啟動 BIOS 即可自動恢復默認值。 2.
2 跳線選擇區 1. CMOS 配置數據清除 (3-pin CLRTC) 在主板上的 CMOS 存儲器中記載著正確的時間與系統硬件 配置等數據,這些數據並不會因電腦電源的關閉而遺失數據 與時間的正確性,因為這個 CMOS 的電源是由主板上的鋰 電池所供應。 1 CLRTC 2 2 3 Normal (Default) Clear RTC 想要清除這些數據,可以依照下列步驟進行: 1. 關閉電腦電源,拔掉電源線; 2. 將 CLRTC 跳線帽由 [1-2](默認值)改為 [2-3] 約五∼十秒鐘(此時即清除 CMOS 數據),然後再將跳線帽改回 [1-2]; 3. 插上電源線,開啟電腦電源; 4.
3. USB 設備喚醒跳線(3-pin USBPWF) 若將此跳線設為 +5V,可通過連接的 USB 設備將電腦從 S1 睡眠模式(CPU 停止工作,DRAM 刷新,系統以低功耗模 式運行)喚醒。若將此跳線設為 +5VSB,可將電腦從 S3 與 S4 睡眠模式(CPU 斷電,DRAM 緩慢刷新,電源以低功耗模 式運行)喚醒。此跳線適用于內部 USB 接口。 USBPWF 1 2 3 2 +5VSB +5V (Default) • 該 USB 設備喚醒跳線需要一個可提供 500mA 電流,5VSB 電壓的電 源支持,傳輸到每一個 USB 插槽。否則,系統將無法運行。 •不管是在正常情況下還是處於睡眠狀態中,電腦所消耗的總電流不能超 過電源供應能力(+5VSB)。 4. 鍵盤和 USB 設備喚醒跳線(3-pin KB_USBPWB) +5V 5.
3 內部連接端口 1. 串口連接插座(10-1 pin COM) COM PIN 1 DCD TXD GND RTS RI RXD DTR DSR CTS 這個插座用來連接串口。將串口模塊的數據線連接到這個插 座,然後將該模塊安裝到機箱後面板空的插槽中。 2. 中央處理器 / 機箱風扇電源插槽(4-pin CPU_FAN、4-pin CHA_FAN) C 3. USB 3.0 擴展套件數據線插座 (20-1 pin) USB3 USB3+5V IntA_P1_SSRXIntA_P1_SSRX+ GND IntA_P1_SSTXIntA_P1_SSTX+ GND IntA_P1_DIntA_P1_D+ GND 這個插槽用來連接額外的 USB 3.0 連接端口模塊,並與 USB 2.0 規格兼容。若是您的機箱提供有 USB 3.0 前面板連 接數據線,將該數據線連接至本插槽,就可擁有前面板 USB 3.
5. Single USB 2.0 擴展套件數據線插座 (5-1 pin) USBE5 +5V DC Data(negative) Data(positive) Groud 這些 USB 擴展套件數據線插槽支持 USB 2.0 規格,將 USB 模塊 數據線連接至任何一個插槽,然後將模塊安裝到機箱後側面板中 開放的插槽。這些 USB 插槽與 USB 2.0 規格兼容,並支持傳輸速 率最高達 480Mbps。 PIN 1 EATX12V +12V DC +12V DC +12V DC +12V DC PIN 1 GND GND GND GND PIN 1 ATX12V +12V DC +12V DC 這些電源插槽用來連接到一個 ATX 電源。 電源所提供的連接插頭已經過特別設計,只能 以一個特定方向插入主板上的電源插槽。找到 正確的插入方向後,僅需穩穩地將之套進插槽 中即可。 GND GND 6.
前面板音頻連接排針(10-1 pin AAFP) HD-audio-compliant pin definition NC MIC2 MICPWR Line out_R NC Line out_L PIN 1 PORT1 L PORT1 R PORT2 R SENSE_SEND PORT2 L PIN 1 建議您將支持高保真(high definition)音頻的 前面板音頻模塊連接到這組排針,如此才能得 到高保真音頻的功能。 AGND NC NC AAFP SENSE2_RETUR 這組音頻外接排針供您連接到前面板的音頻數據 線,除了讓您可以輕鬆地通過主機前面板來控制音頻輸 出/輸入等功能,並且支持 AC’97 或 HD Audio 音頻 標準。將前面板音頻輸出/輸入模塊數據線的一端連接 到這個插槽上。 AGND NC SENSE1_RETUR 8. Legacy AC’97 compliant definition 9.
12. LVDS 連接排針(40-pin LVDS) 這些連接排針用來連接支持低電壓差分信號接口的 LCD 顯示器。 PIN 21 ODD_Lane3_P ODD_Lane3_N ODD_Lane2_P ODD_Lane2_N ODD_Lane1_P ODD_Lane1_N ODD_Lane0_P ODD_Lane0_N EVEN_Lane3_P EVEN_Lane3_N EVEN_Lane2_P EVEN_Lane2_N EVEN_Lane1_P EVEN_Lane1_N EVEN_Lane0_P EVEN_Lane0_N EDID_GND LCD_VCC LCD_VCC LCD_VCC PIN 1 N/C EDID_3.
16.
系統控制面板連接排針 (20-5 pin PANEL) • 硬盤動作指示燈連接排針 (2-pin +HDD_LED-) 您可以連接此組 LED 接針到計算機主機面板 上的硬盤動作指示燈,如此一旦硬盤有讀寫動作 時,指示燈隨即亮起。 +HDD_LED- RESET PLED- PIN 1 SPEAKER +5V_SPKO Ground Ground Speaker PWR_SW PLED+ PLEDPWR Ground 這組排針可連接到計算機主機面板上的系統 電源指示燈。在您啟動計算機並且使用計算機的 情況下,該指示燈會持續亮著;而當指示燈閃爍 時,即表示計算機正處於睡眠模式中。 PANEL +PWR_LED- HDD_LED+ HDD_LEDGround RESET NC PLED+ 這一組連接排針包括了數個連接到電腦主機前面板 的功能接針。 • 系統電源指示燈連接排針(2-pin/3-1 pin +PWR_ LED-) +PWR_LED- * Requires an ATX power supply • 機箱揚聲器連接排針 (4-pin SPEAKER) 這組 4-pin 排
系統控制面板連接排針 (20-3 pin F_PANEL) • 硬盤動作指示燈連接排針 (2-pin +HDD_LED-) +5V GND GND Speaker Intruder# SPEAKER +HDD_LED- RESET GND CHASSIS PIN 1 PLED- 這組排針可連接到計算機主機面板上的系統 電源指示燈。在您啟動計算機並且使用計算機 的情況下,該指示燈會持續亮著;而當指示燈 閃爍時,即表示計算機正處於睡眠模式中。 PWR_SW PLED+ PLEDPWR GND • 系統電源指示燈連接排針 (2-pin/3-1 pin +PWR_ LED-) PANEL +PWR_LED- HDD_LED+ HDD_LEDGND Reset NC PLED+ 這一組連接排針包括了數個連接到電腦主機前面 板的功能接針。 +PWR_LED- * Requires an ATX power supply 您可以連接此組 LED 接針到計算機主機面板 上的硬盤動作指示燈,如此一旦硬盤有讀寫動作時,指示燈隨即亮起。 • 機箱揚聲器連接排針 (4-pin SPEAKER) 這
17. TPM 連接排針 (20-1 pin TPM) PWRDWN GND +3VSB NC LAD0 +3V LAD3 PCIRST# FRAME PCICLK TPM GND PIN 1 NC CLKRUN SERIRQ NC GND LAD1 LAD2 NC 這些排針支持可信任平臺模塊(Trusted Platform Module, TPM)系統,可以安全地存儲密鑰、數字證書、密碼和數據。 一個 TPM 系統可幫助提高網絡安全性,保護數字身份和確保 平臺完整。 GND C_PCICLK_TPM +3V +3V PIN 1 +3VSB S_PCIRST#_TBD 這些排針支持可信任平臺模塊(Trusted Platform Module, TPM)系統,可以安全地存儲密鑰、數字證書、密碼和數據。一 個 TPM 系統可幫助提高網絡安全性,保護數字身份和確保平臺 完整。 PWRDWN F_SERIRQ F_FRAME# F_LAD3 F_LAD2 F_LAD1 F_LAD0 TPM TPM 連接排針 (14-1 pin TPM) 18. M.
20. 顯示器亮度連接排針(8-pin LCD_BLKT_PANEL) LCD_BLKT_PANEL PIN 1 BKLT_EN BKLT_PWM BKLT_PWR BKLT_PWR BKLT_GND/Brightness_GND BKLT_GND/Brightness_GND Brightness_up Brightness_Down 這些連接排針用來控制 LCD 屏幕的背光與亮度,可啟用 LCD 屏幕背光、提供背光控制信號并為前面板的亮度按鈕提 供亮度控制信號。 21. LCD 顯示器開關連接排針(2-pin PANEL_SW) 這組 2-pin 排針用來連接能夠關閉 LCD 顯示器背光的顯示 器開關。 PANEL_SW GND MON_SW# PIN 1 22.
25. DMIC 連接排針(4-pin DMIC) 這些 DMIC 連接排針用來連接用於一體機機箱的數字麥克風 模塊。 +3.3V DMIC_DATA GND DMIC_CLK DMIC PIN 1 26. 自定義連接排針(14-pin CUSTOM) 這些自定義連接排針用來連接可設置附加功能的自定 義模塊。 CUSTOM PIN 1 Prog_LED +3.
4 內置 LED 指示燈 1. 電力指示燈 當主板上內置的電力指示燈(SB_PWR)亮著時,表 示當前系統是處於正常運行、省電模式或者軟關機的狀 態中,並非完全斷電。這個警示燈可用來提醒您在安裝 或卸除任何的硬件設備之前,都必須先卸除電源,等待 警示燈熄滅才可進行。 SB_PWR ON Standby Power OFF Powered Off 2. 硬盤指示燈 (HD_LED) 這個指示燈設計用來顯示硬盤運行的狀態。當指示燈閃爍時表示正在讀取硬盤 的數據或數據正在寫入硬盤中,若是指示燈一直沒有亮起,則表示本主板沒有連 接硬盤或是硬盤沒有作用。 3. Q LEDs (BOOT_DEVICE_LED、VGA_LED、DRAM_LED、CPU_LED) Q 指示燈從主板啟動後依序查看 CPU、內存、顯卡與啟動設備狀態。當發現 錯誤時,在該項目旁的指示燈則會亮燈直到問題解決。通過直觀的方式提供這項 友善的設計,能在短短幾秒內找到問題點。 4. KeyBot 指示燈 (KEYBOT_LED) 這個指示燈會在 KeyBot 按鈕按下後亮燈顯示。 5.
5 主板上的內置開關 當您想要針對未安裝在機箱的裸板或是開放機箱的系統作性能調校時,主板上內 置的開關按鈕與重置按鈕可以方便您迅速地開關機或是重置系統。這個專為超頻者及 專業玩家的設計,可以方便且不間斷地進行調校,並讓性能有效地提升。 1. 啟動開關 本主板擁有啟動開關,讓您可以喚醒系統或啟動,並以亮燈顯示系 統已接上電源為啟動狀態,並提醒您在主板移除或插入任何元件之前要 先關機。 2. 重置開關(RESET) 按下重置開關以重新啟動系統。 RESET 3.
4. CMOS 配置數據清除按鈕(CLR_CMOS) 只有在系統因超頻而死機時按下本按鈕來清除 BIOS 設置信息。 5. KeyBot 按鈕(KeyBot) 按下按鈕可以啟用 KeyBot 功能。 KEBOT KeyBot 功能只支持 USB 鍵盤。 6. Sonic SoundStage 按鈕(SOUNDSTAGE) 按下按鈕可以啟用 Sonic SoundStage 功能。 SOUNDSTAGE 當按下 Sonic SoundStage 後,Q-Code 指示燈上會顯 示當前 Sonic SoundStage 文件的設置檔。 7.