マザーボード インターフェース J11133 改訂版 V2 2016年8月
もくじ マザーボードインターフェース 1-2 1-1 1 ヘッダー....................................................................................................1-3 2 ジャンパー................................................................................................1-4 3 内部コネクター..........................................................................................1-6 4 オンボードLED........................................................................................1-16 5 オンボードボタン/スイッチ...................................
1 CMOS クリアヘッダー (2ピン CLRTC) CMOS クリアヘッダーは、CMOSのリアルタイムクロック (RTC)RAMを消去 するためのものです。CMOS RTC RAMを消去することにより、システム時計、 システムパスワード、および設定パラメータを工場出荷時の状態に戻すこと ができます。システムパスワードなどのシステム情報を含むCMOS RAM デー タの維持は、マザーボード上のボタン型電池により行われています。 CLRTC +3V_BAT GND 1. ヘッダー PIN 1 CMOS RTC RAMを消去する手順 1. コンピューターの電源をオフにし電源ケーブルをコンセントから抜きます。 2. ドライバーなどの金属製品を使用して、2つのピンに数秒間触れショートさせます。 3. 電源コードを差し込み、コンピューターの電源をオンにします。 4. POST画面に「Press F1 to Run SETUP」 と表示されたらを押してUEFI BIOS Utilityを 起動し設定を行います。 2.
2 1. ジャンパー CMOS クリアジャンパー (3ピン CLRTC) CMOS クリアジャンパーは、CMOSのリアルタイムクロック(RTC) RAMを消去するためのものです。CMOS RTC RAMを消去することに より、システム時計、システムパスワード、および設定パラメータを 工場出荷時の状態に戻すことができます。システムパスワードなど のシステム情報を含むCMOS RAM データの維持は、マザーボード上 のボタン型電池により行われています。 1 CLRTC 2 2 3 Normal (Default) Clear RTC CMOS RTC RAMを消去する手順 1. コンピューターの電源をオフにし電源ケーブルをコンセントから抜きます。 2. ジャンパーキャップをピン 1-2(初期設定)からピン 2-3 に移動させショートさせま す。5~10秒ほど待ってから、再びピン 1-2にキャップを戻します。 3. 電源コードを差し込み、コンピューターの電源をオンにします。 4.
USBデバイスウェイクアップジャンパー(3ピン USBPWF) オンボードUSBコネクターに接続されたUSBポートの給電方法を設 定します。接続されたUSBデバイスを使用して、S1ステートからのウェ イクアップを実行するには、ジャンパーキャップを 1-2 (+5V) の位置 に設定します。S3/S4ステートからのウェイクアップを実行するには、 ジャンパーキャップを 2-3 (+5VSB) の位置に設定します。 キーボード/USBデバイスウェイクアップジャンパー (KB_USBPWB) 2 3 +5V +5VSB (Default) ウェイクアップ機能を使用するには、+5VSBラインに1Aを供給可能な電源ユニットが必要 です。 • 総電力消費量が電源供給能力(+5VSB)を上回らないようにご注意ください。 ディスプレイパネルバックライト電源セレクター (3ピン BLKT_PWR_SEL) BLKT_PWR_SEL 設定 3V 5V 12V 2 1 12V (Default) マザーボードインターフェース 1 2 3V (Default) 5V 12V 3 2 3 FP
1. 内部コネクター シリアルポートコネクター (10-1ピン COM) シリアルポート(COMポート)用コネクターです。シリアルポート増設用 ブラケットを接続することができます。 RXD DTR DSR CTS COM PIN 1 CPU、ケース ファンコネクター (4ピン CPU_FAN、4ピン CHA_FAN) 3. PCケース内に十分な空気の流れがないと、マザーボードやコンポ ーネントが損傷する恐れがあります。組み立ての際にはシステム の冷却ファン(吸/排気ファン)を必ず搭載してください。 • CPUファンコネクター(CPU_FAN)は、最大1A(12W)までの CPUファンをサポートします。 CHA_FAN +5V CHA FAN IN CHA FAN PWR GND • CPU_FAN CPU FAN PWM CPU FAN IN CPU FAN PWR GND 冷却ファン用コネクターです。CPUファンやケースファンなど、冷却 ファンの電源ケーブルをこのコネクターに接続します。 C USB 3.0コネクター (20-1ピン) USB 3.
シングルUSB 2.0 コネクター (5-1 ピン) USB 2.0 ポート用コネクターです。USB 2.0 増設用ブラケットやフロントパ ネル USB 2.0 コネクターなどを接続することができます。 USBE5 +5V DC Data(negative) Data(positive) Groud 5. PIN 1 EATX12V +12V DC +12V DC +12V DC +12V DC PIN 1 GND GND GND GND PIN 1 ATX12V GND GND ATX電源コネクター (24ピン EATXPWR、8ピン EATX12V、4ピン ATX12V) 電源ユニット用コネクターです。電源ユニット のメインコネクターやCPU補助電源などを接続 します。電源ケーブルとコネクターにはツメがある ので、お互いがかみ合う方向に正しく接続してくだ さい。 +12V DC +12V DC 6.
フロントパネルオーディオコネクター(10-1ピン AAFP) HD-audio-compliant pin definition デジタルオーディオコネクター (4-1ピン SPDIF_OUT) SPDIF_OUT +5V デジタルオーディオ拡張用コネクターです。デジタルオーディオ拡張ブラ ケット(S/PDIFモジュール)を接続することができます。 DirectKeyコネクター (2ピン DRCT) 2ピンのケーブルスイッチ、または電源ボタンやリセットボタンを接続しま す。UEFI BIOS Utilityの「DirectKey (DRCT)」を有効に設定した場合、起動 時にやを押すことなくこのコネクターに接続したスイッチで 直接UEFI BIOS Utilityを起動することが可能になります。 DRCT DRCT GND 10. NC Legacy AC’97 compliant definition SPDIFOUT GND 9.
LVDSコネクター (40ピン LVDS) LVDS (Low-voltage Differential Signaling) 接続の液晶パネ ルを接続します。 デフォルト設定でLVDS出力が無効になっている場合 は、BIOSでLVDSの項目を有効にしてください。 PIN 1 PIN 21 13. ODD_Lane3_P ODD_Lane3_N ODD_Lane2_P ODD_Lane2_N ODD_Lane1_P ODD_Lane1_N ODD_Lane0_P ODD_Lane0_N EVEN_Lane3_P EVEN_Lane3_N EVEN_Lane2_P EVEN_Lane2_N EVEN_Lane1_P EVEN_Lane1_N EVEN_Lane0_P EVEN_Lane0_N EDID_GND LCD_VCC LCD_VCC LCD_VCC LVDS N/C EDID_3.
16.
システムパネルコネクター (20-5ピン PANEL) • ハードディスクドライブアクティビティ LED (2ピン HDD_LED) PIN 1 +HDD_LED- +5V_SPKO Ground Ground Speaker SPEAKER RESET PLED- システム電源LED(2ピン/3-1ピン PWR_LED) システム電源LED用2ピン/3-1ピンコネクターです。PC ケースなどの電源LEDケーブルを接続します。 このLED はシステムの電源をオンにすると点灯し、システムが スリープ状態に入ると点滅します。 PWR_SW PLED+ PLEDPWR Ground • PANEL +PWR_LED- HDD_LED+ HDD_LEDGround RESET NC PLED+ PCケースのボタンやLEDケーブルを取り付けることができ ます。 +PWR_LED- * Requires an ATX power supply ハードディスクドライブアクティビティLED用2ピンコ ネクターです。マザーボード上のSATAポートに接続し ているストレージドライブがデータの読み
システムパネルコネクター (20-3ピン PANEL) • ハードディスクドライブアクティビティ LED (2ピン HDD_LED) +5V GND GND Speaker Intruder# SPEAKER +HDD_LED- RESET GND CHASSIS PIN 1 PLED- システム電源LED(2ピン/3-1ピン PWR_LED) システム電源LED用2ピン/3-1ピンコネクターです。 PCケースなどの電源LEDケーブルを接続します。 この LEDはシステムの電源をオンにすると点灯し、システ ムがスリープ状態に入ると点滅します。 PWR_SW PLED+ PLEDPWR GND • PANEL +PWR_LED- HDD_LED+ HDD_LEDGND Reset NC PLED+ PCケースのボタンやLEDケーブルを取り付けることができ ます。 +PWR_LED- * Requires an ATX power supply ハードディスクドライブアクティビティLED用2ピンコ ネクターです。マザーボード上のSATAポートに接続しているストレージドライブが
GND NC NC GND NC NC GND NC NC GND S_WAKE# L1_WIFI_CLKREQ# GND C_PCIE_WIFI# C_PCIE_WIFI GND X_WIFI_RXN X_WIFI_RXP GND X_WIFI_TXN X_WIFI_TXP GND NC NC NC NC NC NC NC GND S_USB_PN10_R S_USB_PP10_R GND 18. 19. M.2 socket 1 (Key E) タイプのWi-Fi カードまたはWi-Fi ベースのコンボデバイスを取り付けることができます。 マザーボードインターフェース VCC VCC NC NC NC NC NC NC GND NC NC NC NC NC CL_RST# CL_DATA CL_CLK NC NC NC S_SUSCLK S_PLTRST# BT_ISOLATE#_R M2_ISOLATE#_R NC NC NC NC NC NC NC VCC VCC PWRDWN F_SERIRQ F_FRAME# F_LAD3 F_LAD2 F_LAD1 F_LAD0 M.
20. フラットパネルディスプレイ輝度制御コネクター (8ピン LCD_BLKT_PANEL) 液晶パネルのバックライトと輝度を制御する際に使用します。このコ LCD_BLKT_PANEL ネクターからは輝度制御信号は送出され、フロントパネルなどでバ ックライトや輝度の制御を可能にすることができます。 BKLT_EN BKLT_PWM BKLT_PWR BKLT_PWR BKLT_GND/Brightness_GND BKLT_GND/Brightness_GND Brightness_up Brightness_Down PIN 1 21. 液晶パネルスイッチヘッダー (2ピン PANEL_SW) 液晶パネルのバックライトをオン/オフするためのスイッチを接続する ことができます。 PANEL_SW GND MON_SW# PIN 1 22.
25. DMICコネクター (4ピン DMIC) オールインワンタイプのPCケースで使用されるデジタルマイクロフォンモ ジュールを接続することができます。 +3.3V DMIC_DATA GND DMIC_CLK DMIC PIN 1 26. カスタムヘッダー (14ピン CUSTOM) 追加機能などのカスタマイズされたモジュールを接続する際に利 用することができます。 CUSTOM PIN 1 Prog_LED +3.
4 1. オンボードLED スタンバイ電源LED (SB_PWR) スリープモードやソフトオフモードを含む、スタンバイ電力が供 給されている間スタンバイ電源LEDが点灯します。コンポーネン トの取り付けや取り外しを行なう際は、電源ケーブルを抜くなど してスタンバイ電源LEDが消灯した事を確認してから行ってくだ さい。 2. SB_PWR ON Standby Power OFF Powered Off ハードディスクLED (HD_LED) ハードディスクLEDはハードディスクやSSDなどのSATAストレージデバイスの動作状態を示 し、データの書き込み/読み込み中に点滅します。マザーボードにSATAストレージデバイス が接続されていない、またはSATAストレージデバイスが正常に動作していない場合はLED は点灯しません。 3. 4.
5 1. オンボードボタン/スイッチ 電源ボタン (START) 電源ボタンではシステムの電源をオンにする、またはウェイクアップすることが できます。 このボタンはシステムが電源に接続されているときも点灯します。コン ポーネントの取り付けや取り外しを行う際は、電源ケーブルを抜くなどして電源ボ タンが消灯した事を確認してから行ってください。 2. リセットボタン (RESET) リセットボタンを押すと、システムは強制的に再起動します。リセットボタンを 押すとシステムは強制的に再起動が実行されます。保存されていない作業中 のデータは削除されてしまいます。 3.
4. CMOSクリアボタン (CLR_CMOS) CMOSクリアボタンを押すことで、CMOSのリアルタイムクロック (RTC) RAMを消去することができます。CMOS RTC RAMを消去することにより、 システム時計、システムパスワード、およびシステム設定パラメータをデ フォルト状態に戻すことができます。 5. KeyBot ボタン (KeyBot) KeyBot機能の有効/無効を切り替えることができます。 KEBOT KeyBot機能は、特定のUSBポートに接続されたキーボードでのみご利 用いただけます。 6. Sonic SoundStage ボタン (SOUNDSTAGE) Sonic SoundStageのプロファイルを切り替えます。 SOUNDSTAGE 現在のプロファイルはQ-Code LEDで確認することができます。 7.