® A7V-E JumperFree™ PC133/VC133 200MHz FSB AGP 4X Socket A Motherboard USER’S MANUAL
USER'S NOTICE No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS CONTACT INFORMATION ASUSTeK COMPUTER INC. (Asia-Pacific) Marketing Address: Telephone: Fax: Email: 150 Li-Te Road, Peitou, Taipei, Taiwan 112 +886-2-2894-3447 +886-2-2894-3449 info@asus.com.tw Technical Support MB/Others (Tel): +886-2-2890-7121 (English) Notebook (Tel): +886-2-2890-7122 (English) Desktop/Server (Tel):+886-2-2890-7123 (English) Fax: +886-2-2893-7775 Email: tsd@asus.com.tw WWW: www.asus.com.tw FTP: ftp.asus.com.
CONTENTS 1. INTRODUCTION 7 1.1 How This Manual Is Organized ................................................. 7 1.2 Item Checklist ............................................................................ 7 2. FEATURES 8 2.1 The ASUS A7V-E ...................................................................... 8 2.1.1 Specifications .................................................................. 8 2.1.2 Special Features ............................................................ 10 2.1.
CONTENTS 4.3.2 Keyboard Features ........................................................ 51 4.4 Advanced Menu ....................................................................... 53 4.4.1 Chip Configuration ....................................................... 56 4.4.2 I/O Device Configuration ............................................. 59 4.4.3 PCI Configuration ......................................................... 62 4.4.4 Shadow Configuration ..................................................
FCC & DOC COMPLIANCE Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
1. INTRODUCTION 1. INTRODUCTION Manual / Checklist 1.1 How This Manual Is Organized This manual is divided into the following sections: 1. 2. 3. 4. 5. 6. 7. INTRODUCTION FEATURES HARDWARE SETUP BIOS SETUP SOFTWARE SETUP SOFTWARE REFERENCE APPENDIX Manual information and checklist Production information and specifications Intructions on setting up the motherboard.
2. FEATURES 2.1 The ASUS A7V-E The ASUS A7V-E motherboard is carefully designed for the demanding PC user who wants advanced features processed by the fastest processors. 2.1.1 Specifications • 2. FEA TURES Specifications • • • • • • • • 8 AMD Athlon™/Duron™ Processor Support: Supports Socket A-based AMD Athlon™/Duron™ processors.
2. FEATURES • • • • • • • • • • • Wake-On-Ring Connector: Supports Wake-On-Ring activity through a PCI modem card that supports a WOR connector. USB: Supports up to 4 USB ports, two on the back panel and two midboard, for more peripheral connectivity options. PC Health Monitoring: Provides an easy way to examine and manage system status information, such as CPU and systerm voltages, temperatures, and fan status through the onboard hardware monitoring and the bundled ASUS PC Probe.
2. FEATURES 2.1.2 Special Features • 2. FEA TURES Performance • • • ACPI Ready: Advanced Configuration Power Interface (ACPI) provides more Energy Saving Features for operating systems that support OS Direct Power Management (OSPM) functionality. With these features implemented in the OS, PCs can be ready around the clock, yet satisfy all the energy saving standards. To fully utilize the benefits of ACPI, an ACPI-supported OS, such as Windows 98 must be used.
2. FEATURES • VCM/SDRAM Optimized Performance: This motherboard supports a new generation memory, NEC’s 64Mb Virtual Channel Memory (VCM) Synchronous Dynamic Random Access Memory (SDRAM), which is compatible to the industry standard SDRAM. The VCM’s core design provides up to 50% higher SDRAM speed at reduced power consumption of about 30%. This motherboard also supports standard SDRAM, which increases the data transfer rate (1.
2. FEATURES 2.2 Motherboard Components See opposite page for locations. Location Processor Support Socket A for Socket A AMD Athlon/Duron Processors ........... 3 (NOTE: CPU thermal sensor is integrated on the motherboard, located near the center of the CPU heat source, just below the CPU socket) Feature Setting DIP Switches (CPU Speed) ............................. 7 2. FEA TURES Motherboard Parts Feature Setting DIP Switches (Clock Multiplier) ..................
2. FEATURES 2.2.1 Component Locations 1 2 3 4 5 67 24 2.
3. HARDWARE SETUP 3.1 Motherboard Layout 24.5cm (9.64in) PS/2 CPU_FAN T: Mouse B: Keyboard Socket A CHASSIS Realtek Fast Enternet Mic In CD Accelerated Graphic Port (AGP) CHASS_FAN 0 1 2 3 CLRTC AUX Audio Codec HPHONE 2Mbit Flash EEPROM (Programmable BIOS) JEN PCI Slot 1 VIA VT82C686B Chipset PCI Slot 2 WOLCON MODEM PCI Slot 3 ® PCI Slot 4 IR PLED USB2 SMB PCI Slot 5 DIP Switches PCI Slot 6 A7V-E IDELED Grayed components are optional at the time of purchase.
3. HARDWARE SETUP 3.2 Layout Contents Motherboard Settings 1) JEN 2) SW1 1–4 p. 18 JumperFree Mode (JumperFree/Jumper Mode) p. 20 CPU External Frequency Setting Expansion Slots/Sockets 1) 2) 3) 4) 5) System Memory DIMM1/2 Socket 462 (Socket A) PCI1/2/3 AGP p.21 p.22 p.23 p.24 p.26 System Memory Support DIMM Memory Module Support CPU Support 32-bit PCI Bus Expansion Slots Accelerated Graphics Port (AGP) Connectors 10) 11) 12) 13) 14) 15) 16) 17) 18) 19) 20) 21) 22) 23) 24) 25) 26) PS2KBMS p.
3. HARDWARE SETUP 3.3 Hardware Setup Procedure Before using your computer, you must complete the following steps: 1. Check Motherboard Settings 2. Install Memory Modules 3. Install the Central Processing Unit (CPU) 4. Install Expansion Cards 5. Connect Ribbon Cables, Panel Wires, and Power Supply 6. Setup the BIOS Software 3.4 Motherboard Settings This section explains in detail how to change your motherboard’s function settings through the use of switches and/or jumpers. 3.
3. HARDWARE SETUP Motherboard Features Settings (DIP Switches - SW1) The motherboard’s onboard functions are adjusted through the DIP switches. The white block represents the switch’s position. The example below shows all the switches in the OFF position. ON 1 2 3 4 5 ON OFF CLOCK TABLE 5. Frequency Selection 4. Frequency Selection 3. Frequency Selection 2. Frequency Selection 1. Frequency Selection 0 1 0 1 DSFID ON ON A7V-E A7V-E DIP Switches 1 2 3 4 5 OFF 1. Frequency Multiple 2.
3. HARDWARE SETUP 2) CPU External Frequency Setting (SW1 Switches 1–5) This option tells the clock generator what frequency to send to the CPU, SDRAM, and the chipset. This allows the selection of the CPU’s External frequency. The CPU External Frequency multiplied by the Frequency Multiple equals the CPU’s Internal frequency (the advertised CPU speed). For JumperFree Mode, the default setting enabling BIOS control is 100 MHz.
3. HARDWARE SETUP 3) CPU Core BUS Frequency Multiple (DSFID Switches 1–5) For unlocked CPUs only, the DSFID switches set the frequency multiple, which determines the relationship between the frequency of the CPU and the CPU Bus frequency. Notes: If the Frequency Multiple of your processor is locked, setting the Frequency Multiple will have no effect. ON ON ON ON 0 1 0 1 1 2 3 4 5 5.0x ON 1 2 3 4 5 5.5x ON 1 2 3 4 5 1 2 3 4 5 6.0x ON 1 2 3 4 5 7.0x ON 1 2 3 4 5 7.5x 1 2 3 4 5 6.
3.5 System Memory (DIMM) This motherboard uses only Dual Inline Memory Modules (DIMMs). Two sockets are available for 3.3Volt (power level) unbuffered Synchronous Dynamic Random Access Memory (SDRAM) of 8, 16, 32, 64, 128, 256, or 512MB to form a memory size between 8MB to 1GB. One side (with memory chips) of the DIMM takes up one row on the motherboard. This motherboard also supports NEC’s Virtual Channel (VC) SDRAMs.
3.5.2 Memory Installation WARNING! Make sure that you unplug your power supply when adding or removing memory modules or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards (see 3.3 Hardware Setup Procedure for more information). Insert the module(s) as shown. Because the number of pins are different on either side of the breaks, the module will only fit in the orientation shown. DRAM SIMM modules have the same pin contacts on both sides.
3. HARDWARE SETUP (This page intentionally left blank.) 3.
3. HARDWARE SETUP 3.6 Central Processing Unit (CPU) The motherboard provides a Socket 462 or Socket A for CPU installation. The CPU that came with the motherboard should have a fan and heatsink attached to it to prevent overheating. If this is not the case, then purchase and install a set before you turn on your system. WARNING! Make sure that the heatsink is mounted tightly against the processor.
3. HARDWARE SETUP 3.7 Expansion Cards WARNING! Unplug your power supply when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 3.7.1 Expansion Card Installation Procedure 3. H/W SETUP Expansion Cards 1. Read the documentation for your expansion card and make any necessary hardware or software settings for your expansion card, such as jumpers. 2.
3. HARDWARE SETUP 3.7.2 Assigning IRQs for Expansion Cards Some expansion cards need an IRQ to operate. Generally, an IRQ must be exclusively assigned to one use. In a standard design, there are 16 IRQs available but most of them are already in use, leaving 6 IRQs free for expansion cards. If your motherboard has PCI audio onboard, an additional IRQ will be used. If your motherboard also has MIDI enabled, another IRQ will be used, leaving 4 IRQs free.
3. HARDWARE SETUP 3.7.3 Accelerated Graphics Port (AGP) This motherboard provides an Accelerated Graphics Port (AGP) slot to support AGP graphics cards, such as an ASUS AGP-V7700 GeForce2 GTS graphics card. CAUTION! To avoid damaging your AGP graphics card, your computer’s power supply should be unplugged before inserting your graphics card into the slot. 0 1 0 1 AGP Card without Retention Notch ® 3.
3. HARDWARE SETUP 3.8 External Connectors WARNING! Some pins are used for connectors or power sources. These are clearly distinguished from jumpers in the Motherboard Layout. Placing jumper caps over these connector pins will cause damage to your motherboard. IMPORTANT: Ribbon cables should always be connected with the red stripe to Pin 1 on the connectors. Pin 1 is usually on the side closest to the power connector on hard drives and CD-ROM drives, but may be on the opposite side on floppy disk drives.
3. HARDWARE SETUP 3) Universal Serial BUS Ports 0 & 1 (Black two 4-pin USB) Two USB ports are available for connecting USB devices. If these are not enough, a USB header is available for two additional USB port connectors. See USB Headers later in this section. USB 1 Universal Serial Bus (USB) 2 3. H/W SETUP Connectors 4) Serial Port Connectors (Teal/Turquoise 9-pin COM1 / COM2) Two serial ports can be used for pointing devices or other serial devices.
3. HARDWARE SETUP 6) Game/MIDI Connector (Gold 15-pin GAME_AUDIO) (optional) You may connect game joysticks or game pads to this connector for playing games. Connect MIDI devices for playing or editing professional audio. Game/MIDI (15-pin Female) 3. H/W SETUP Connectors 7) Audio Port Connectors (Three 1/8” GAME_AUDIO) (optional) Line Out (lime) can be connected to headphones or preferably powered speakers.
3. HARDWARE SETUP 0 1 ® Primary IDE Connector 0 1 3. H/W SETUP Connectors Secondary IDE Connector 9) Primary (Blue) / Secondary IDE Connectors (40-1 pin IDE1/IDE2) These connectors support the provided UltraDMA/100 IDE hard disk ribbon cable. Connect the cable’s blue connector to the motherboard’s primary (recommended) or secondary IDE connector, and then connect the gray connector to your UltraDMA/100 slave device (hard disk drive) and the black connector to your UltraDMA/100 master device.
3. HARDWARE SETUP 11) Chassis Intrusion Lead (2 pin CHASSIS) This requires an external detection mechanism such as a chassis intrusion monitor/sensor or microswitch. The sensor is triggered when a high level signal is sent to the Chassis Signal lead, which occurs when a panel switch or light detector is triggered. This function requires the optional ASUS CIDB chassis intrusion module to be installed (see 7. APPENDIX).
3. HARDWARE SETUP 13) Wake-On-LAN Connector (3-pin WOL_CON) This connector connects to a LAN card with a Wake-On-LAN output, such as the ASUS PCI-L101 Ethernet card (see 7. Appendix). The connector powers up the system when a wakeup packet or signal is received through the LAN card. IMPORTANT: This feature requires that Wake-On-LAN features are enabled (see 4.4.3 Power Management) and that your system has an ATX power supply with at least 720mA +5V standby power.
3. HARDWARE SETUP 15) CPU, Power Supply, Chassis Fan Connectors (3-pin CPU_FAN, PS_FAN, CHASS_FAN) These connectors support cooling fans of 350mA (4.2 Watts) or less. Orientate the fans so that the heat sink fins allow airflow to go across the onboard heat sink(s) instead of the expansion slots. Depending on the fan manufacturer, the wiring and plug may be different. The red wire should be positive, while the black should be ground.
3. HARDWARE SETUP 16) Internal Audio Connectors (4-pin CD_IN, AUX, MODEM) These connectors allow you to receive stereo audio input from such sound sources as a CD-ROM, TV tuner, or MPEG card. The MODEM connector allows the onboard audio to interface with a voice modem card with a similar connector.
3. HARDWARE SETUP 18) USB Header (10-1 pin USB2) If the USB port connectors on the back panel are inadequate, this USB header is available for two additional USB port connectors. Connect the USB headers to the 2-port USB connector set and mount the bracket to an open slot on your chassis. 01 01 USB2 USB Power USBP3– USBP3+ GND 10 6 5 1 ® USB Power USBP2– USBP2+ GND NC A7V-E 3.
3. HARDWARE SETUP 20) ATX Power Supply Connector (20-pin block ATXPWR) This connector connects to an ATX power supply. The plug from the power supply will only insert in one orientation because of the different hole sizes. Find the proper orientation and push down firmly making sure that the pins are aligned. IMPORTANT: Make sure that your ATX power supply can supply at least 10mA on the +5-volt standby lead (+5VSB).
3. HARDWARE SETUP The following PANEL illustration is used for items 21–25. PLED- ExtSMI# Ground PWR GND Reset Ground 0 1 PLED+ +5V Ground Ground Speaker 0 1 Power LED Speaker Connector Reset SW ® SMI Lead A7V-E A7V-E System Panel Connectors ATX Power Switch* * Requires an ATX power supply. ASUS A7V-E User’s Manual 3. H/W SETUP Connectors 22) System Warning Speaker Connector (4-pin SPEAKER) This 4-pin connector connects to the case-mounted speaker.
3. HARDWARE SETUP (This page intentionally left blank.) 3.
3. HARDWARE SETUP 3.9 Starting Up the First Time 1. After all connections are made, close the system case cover. 2. Be sure that all switches are off (in some systems, marked with ). 3. Connect the power supply cord into the power supply located on the back of your system case according to your system user’s manual. 4. Connect the power cord into a power outlet that is equipped with a surge protector. 3. H/W SETUP Powering Up 5. You may then turn on your devices in the following order: a. Your monitor b.
3. HARDWARE SETUP 7. During power-on, hold down to enter BIOS setup. Follow the instructions in 4. BIOS SETUP. * Powering Off your computer: You must first exit or shut down your operating system before switching off the power switch. For ATX power supplies, you can press the ATX power switch after exiting or shutting down your operating system.
4. BIOS SETUP 4.1 Managing and Updating Your BIOS 4.1.1 Upon First Use of the Computer System It is recommended that you save a copy of the original motherboard BIOS along with a Flash Memory Writer utility (AFLASH.EXE) to a bootable floppy disk in case you need to reinstall the BIOS later. AFLASH.EXE is a Flash Memory Writer utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the motherboard. This file works only in DOS mode.
4. BIOS SETUP 5. Select 1. Save Current BIOS to File from the Main menu and press . The Save Current BIOS To File screen appears. 6. Type a filename and the path, for example, A:\XXX-XX.XXX and then press . 4.1.2 Updating BIOS Procedures WARNING! Only update your BIOS if you have problems with your motherboard and you know that the new BIOS revision will solve your problems. Careless updating can result in your motherboard having more problems! 4. BIOS SETUP Updating BIOS 1.
4. BIOS SETUP 6. When prompted to confirm the BIOS update, press Y to start the update. 4. BIOS SETUP Updating BIOS 7. The utility starts to program the new BIOS information into the flash ROM. The boot block will be updated automatically only when necessary. This will minimize the chance that a failed update will prevent your system from booting up. When the programming is finished, Flashed Successfully will be displayed. 8. Follow the onscreen instructions to continue.
4. BIOS SETUP 4.2 BIOS Setup Program This motherboard supports a programmable EEPROM that can be updated using the provided utility as described in 4.1 Managing and Updating Your BIOS. The utility is used if you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section describes how to configure your system using this utility. 4. BIOS SETUP The EEPROM on the motherboard stores the Setup utility.
4. BIOS SETUP 4.2.1 BIOS Menu Bar The top of the screen has a menu bar with the following selections: MAIN Use this menu to make changes to the basic system configuration. ADVANCED Use this menu to enable and make changes to the advanced features. POWER Use this menu to configure and enable Power Management features. BOOT Use this menu to configure the default system device used to locate and load the Operating System. EXIT Use this menu to exit the current menu or specify how to exit the Setup program.
4. BIOS SETUP General Help In addition to the Item Specific Help window, the BIOS setup program also provides a General Help screen. This screen can be called up from any menu by simply pressing or the + combination. The General Help screen lists the legend keys with their corresponding alternates and functions. Saving Changes and Exiting the Setup Program See 4.7 Exit Menu for detailed information on saving changes and exiting the setup program.
4. BIOS SETUP 4.3 Main Menu When the Setup program is accessed, the following screen appears: 4. BIOS SETUP Main Menu System Time [XX:XX:XX] Sets your system to the time that you specify (usually the current time). The format is hour, minute, second. Valid values for hour, minute and second are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59). Use the or + keys to move between the hour, minute, and second fields.
4. BIOS SETUP 4. BIOS SETUP NOTE: Before attempting to configure a hard disk drive, make sure you have the configuration information supplied by the manufacturer of the drive. Incorrect settings may cause your system to not recognize the installed hard disk. To allow the BIOS to detect the drive type automatically, select [Auto]. Type [Auto] Select [Auto] to automatically detect an IDE hard disk drive.
4. BIOS SETUP IMPORTANT: If your hard disk was already formatted on an older previous system, incorrect parameters may be detected. You will need to enter the correct parameters manually or use low-level format if you do not need the data stored on the hard disk. If the parameters listed differ from the ones used when the disk was formatted, the disk will not be readable.
4. BIOS SETUP Head This field configures the number of read/write heads. Refer to your drive documentation to determine the correct value to enter into this field. NOTE: To make changes to this field, the Type field must be set to [User Type HDD] and the Translation Method field must be set to [Manual]. Sector This field configures the number of sectors per track. Refer to your drive documentation to determine the correct value to enter into this field.
4. BIOS SETUP Other options for “Type:” are: [CD-ROM] - for IDE CD-ROM drives [LS-120] - for LS-120 compatible floppy disk drives [ZIP] - for ZIP-100 compatible disk drives [MO] - for IDE magneto optical disk drives [Other ATAPI Device] - for IDE devices not listed here After using the legend keys to make your selections on this sub-menu, press the key to exit back to the Main menu.
4. BIOS SETUP 0 1 4. BIOS SETUP Supervisor Password [Disabled] / User Password [Disabled] These fields allow you to set the passwords. To set the password, highlight the appropriate field and press . Type in a password and press . You can type up to eight alphanumeric characters. Symbols and other keys are ignored. To confirm the password, type the password again and press the . The password is now set to [Enabled]. This password allows full access to the BIOS Setup menus.
4. BIOS SETUP 4.4 Advanced Menu 4. BIOS SETUP Advanced Menu Operating Frequency Setting [User Define] When the motherboard is set to JumperFree™ mode, this field allows you to configure the external frequency of your CPU. Select [User Define] if you want to make changes to the CPU Frequency field. When [Standard] is selected, CPU (external) Frequency will be fixed at 100MHz.
4. BIOS SETUP CPU Level 1 Cache, CPU Level 2 Cache [Enabled] These fields allow you to choose from the default of [Enabled] or choose [Disabled] to turn on or off the CPU’s Level 1 and Level 2 built-in cache. Configuration options: [Disabled] [Enabled] CPU Level 2 Cache ECC Check [Disabled] This function controls the ECC capability in the CPU level 2 cache.
4. BIOS SETUP Notes for JumperFree Mode System Hangup If your system crashes or hangs due to improper frequency settings, power OFF your system and restart. The system will start up in safe mode running at a DRAM-to-CPU frequency ratio of 3:3 and a bus speed of 100MHz. You will then be led to BIOS setup to adjust the configurations. 4.
4. BIOS SETUP 4. BIOS SETUP (Scroll down to see more items as shown.) Onboard PCI IDE Enable [Both] You can select to enable the primary IDE channel, secondary IDE channel, both, or disable both channels. Configuration options: [Both] [Primary] [Secondary] [Disabled] Spread Spectrum Control [Enabled] Leave on default setting. Spread spectrum typically reduces system electromagnetic interference (EMI) by 8dB to 10dB.
4. BIOS SETUP SDRAM Configuration [By SPD] This sets the optimal timings for SDRAM related fields, depending on the memory modules that you are using. Default setting is [By SPD], which configures the subsequent 3 items by reading the contents in the SPD (Serial Presence Detect) device. The EEPROM on the memory module stores critical parameter information about the module, such as memory type, size, speed, voltage interface, and module banks.
4. BIOS SETUP Memory Early/Delay Write [Auto] Configuration options: [0.0 ns] [0.5 ns]...[Auto] Memory Data Driving [Auto] Configuration options: [Auto] [Strong] [Weak] Memory Address Driving [Auto] Configuration options: [Auto] [Strong] [Weak] DIMM Interleave Setting [Auto] Configuration options: [Auto] [Disabled] I/O Recovery Time [Disabled] Configuration options: [Disabled] [Enabled] Graphics Aperture Size [32MB] This feature allows you to select the size of mapped memory for AGP graphic data.
4. BIOS SETUP 4.4.2 I/O Device Configuration Onboard FDC Swap A & B [No Swap] This field allows you to reverse the hardware drive letter assignments of your floppy disk drives. Configuration options: [No Swap] [Swap AB] 4. BIOS SETUP I/O Device Config Onboard Serial Port 1 [3F8H/IRQ4] Onboard Serial Port 2 [2F8H/IRQ3] These fields allow you to set the addresses for the onboard serial connectors. Serial Port 1 and Serial Port 2 must have different addresses.
4. BIOS SETUP Onboard Parallel Port [378H/IRQ7] This field sets the address of the onboard parallel port connector. If you disable this feature, Parallel Port Mode and ECP DMA Select configurations will not be available. Configuration options: [Disabled] [378H/IRQ7] [278H/IRQ5] Parallel Port Mode [ECP+EPP] This field allows you to set the operation mode of the parallel port.
4. BIOS SETUP Onboard Legacy Audio Support [Disabled] The onboard chipset is integrated with a SoundBlaster Pro controller. To use it, you must enable this field. Leave on the default setting [Disabled] if you want to use an add-on audio device. NOTE: To display the rest of the setup items, this field must be enabled (as shown below). Sound Blaster Emulation [Disabled] Select [Enabled] for this field if you want to use the Sound Blaster™ emulation feature. 4.
4. BIOS SETUP 4.4.3 PCI Configuration 4. BIOS SETUP PCI/VGA Palette Snoop [Disabled] Some nonstandard VGA cards, such as graphics accelerators or MPEG video cards, may not show colors properly. The setting [Enabled] should correct this problem. Otherwise, leave this on the default setting of [Disabled]. Configuration options: [Disabled] [Enabled] PCI Latency Timer [32] Leave on default setting for best performance vs. stability.
4. BIOS SETUP USB Function [Enabled] This motherboard supports Universal Serial Bus (USB) devices. Set to [Enabled] if you want to use USB devices. Configuration options: [Disabled] [Enabled] Primary VGA BIOS [PCI Card] If your computer has both PCI and AGP VGA cards, this field allows you to select which of the cards will act as your primary graphics card. [AGP Card] uses the AGP card as your primary card. The default, [PCI Card], allows your PCI graphics card to take precedence when detected.
4. BIOS SETUP PCI/PNP DMA Resource Exclusion 4. BIOS SETUP PCI Configuration DMA x Reserved for Legacy Device [No/ICU] These fields indicate whether or not the displayed DMA channel for each field is being used by an onboard legacy (non-PnP) device. The default setting indicates either that the displayed DMA channel is not used or an ICU is being used to determine if an ISA device is using that channel.
4. BIOS SETUP PCI/PNP UMB Resource Exclusion ASUS A7V-E User’s Manual 4. BIOS SETUP PCI Configuration Reserved MEM Block BASE [No/ICU] This field allows you to set the base address and block size of an onboard legacy ISA device that uses any memory segment within the C800 and DFFF address range.
4. BIOS SETUP 4.4.4 Shadow Configuration 4. BIOS SETUP C8000-DFFFF Shadow [Disabled] These fields are used for shadowing other expansion card ROMs. If you install other expansion cards with ROMs on them, you will need to know which addresses the ROMs use to shadow them specifically. Shadowing a ROM reduces the memory available between 640K and 1024K by the amount used for this purpose.
4. BIOS SETUP 4.5 Power Menu The Power menu allows you to reduce power consumption. This feature turns off the video display and shuts down the hard disk after a period of inactivity. 4. BIOS SETUP Power Menu Power Management [User Define] This option must be enabled to use any of the automatic power saving features. If this menu item is set to [Disabled], power management features will not function regardless of other field settings on this menu.
4. BIOS SETUP Video Off Option [Suspend -> Off ] This field determines when to activate the video off feature for monitor power management. Configuration options: [Always On] [Suspend -> Off] Video Off Method [DPMS OFF] This field defines the video off features. The DPMS (Display Power Management System) feature allows the BIOS to control the video display card if it supports the DPMS feature. [Blank Screen] only blanks the screen (use this for monitors without power management or “green” features.
4. BIOS SETUP 4.5.1 Power Up Control 4. BIOS SETUP Power Up Control AC PWR Loss Restart [Disabled] This allows you to set whether you want your system to reboot after the power has been interrupted. [Disabled] leaves your system off and [Enabled] reboots your system. [Previous State] sets your system back to the state it is before the power interruption.
4. BIOS SETUP Automatic Power Up [Disabled] This allows an unattended or automatic system power up. You may configure your system to power up at a certain time of the day by selecting [Everyday] or at a certain time and day by selecting [By Date]. NOTE: Automatic Power Up will not work if the system is powered down by operating systems, such as Windows 98, that have ACPI support enabled. Configuration options: [Disabled] [Everyday] [By Date] 4.
4. BIOS SETUP 4.6 Boot Menu Boot Sequence 4. BIOS SETUP Hardware Monitor The Boot menu allows you to select among the four possible types of boot devices listed using the up and down arrow keys. By using the <+> or key, you can promote devices and by using the <-> key, you can demote devices. Promotion or demotion of devices alters the priority which the system uses to search for a boot device on system power up.
4. BIOS SETUP Other Boot Device Select [INT18 Device (Network)] Configuration options: [Disabled] [SCSI/Onboard ATA Boot Device] [INT18 Device (Network)] Plug & Play O/S [No] This field allows you to use a Plug-and-Play (PnP) operating system to configure the PCI bus slots instead of using the BIOS. When [Yes] is selected, interrupts may be reassigned by the OS. When a non-PnP OS is installed or you want to prevent reassigning of interrupt settings, select the default setting of [No].
4. BIOS SETUP 4.7 Exit Menu Once you have made all of your selections from the various menus in the Setup program, you should save your changes and exit Setup. Select Exit from the menu bar to display the following menu: Boot Menu 4. BIOS SETUP NOTE: Pressing does not exit this menu. You must select one of the options from this menu or from the legend bar to exit this menu.
4. BIOS SETUP Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When this option is selected or if is pressed, a confirmation is requested. Select [Yes] to load default values. You can now select Exit Saving Changes or make other changes before saving the values to the non-volatile RAM. Discard Changes This option allows you to discard the selections you made and restore the values you previously saved.
5. SOFTWARE SETUP 5.1 Install Operating System You should always use the latest operating system and updates when using new hardware to ensure full compliancy. You may use any version of Windows 98/2000/ Millenium, but for Windows 95, you must use OSR 2.0 or later. For Windows NT 4.0, you must use Service Pack 3.0 or later. 5.2 Start Windows When you start Windows 98 for the first time after installing your motherboard, Windows will detect all plug-and play devices.
5. SOFTWARE SETUP 5.3 A7V-E Series Motherboard Support CD NOTE: The support CD contents are subject to change at any time without notice. To begin using your support CD disc, just insert it into your CD-ROM drive and the support CD installation menu should appear. If the menu does not appear, doubleclick or run D:\ASSETUP.EXE (assuming that your CD-ROM drive is drive D:). 5.3.1 Installation Menu • • • • • • • Support CD 5.
5. SOFTWARE SETUP • • • • • • Intel LDCM 6.1 Client Setup: (optional) LANDesk Client Manager software monitors the Client system and operates hardware management features. ASUS BIOS Flash Utility for LDCM 6.1: (optional) Installs a utility that remotely flashes to a client PC’s BIOS software when used in conjunction with Intel LDCM Administrator. Show Motherboard Information: Allows you to view information about your motherboard, such as product name, BIOS version, and CPU.
5. SOFTWARE SETUP (This page was intentionally left blank.) 5.
7. APPENDIX 7. APPENDIX ASUS LAN Card 7.1 PCI-L101 Fast Ethernet Card LEDs LAN Activity Output Signal Intel Chipset RJ45 Wake on LAN Output Signal ASUS Motherboard type Other If you are using the ASUS PCI-L101 on an ASUS motherboard, leave the jumper on its defaut setting of “ASUS.” If you are using another brand of motherboard, set the jumper to “Other.” Connect the Wake on LAN (WOL) output signal to the motherboard’s WOL_CON in order to utilize the wake on LAN feature of the motherboard.
7. APPENDIX 7.1.1 Features 7. APPENDIX ASUS LAN Card • • • • • • • • • • • • Intel 82558 Ethernet LAN Controller (Fully integrated 10BASE-T/100BASE-TX) Wake-On-LAN Remote Control Function Supported PCI Bus Master Complies to PCI Local Bus Rev. 2.1 specifications Consists of MAC & PHY (10/100Mbps) interfaces Complies to IEEE 802.3 10BASE-T and IEEE 802.3u 100BASE-TX interfaces Fully supports 10BASE-T & 100BASE-TX operations through a single RJ45 port Supports 32-bit Bus Master Technology / PCI Rev. 2.
7. APPENDIX 7.3 Glossary Bus PCI AGP 1X AGP 2X AGP 4X Bus Frequency 33MHz 66MHz 66MHz 66MHz Bandwidth 33MHz 66MHz 133MHz 266MHz 7 . APPENDIX Glossary 1394 1394 is the IEEE designation for the high performance serial bus at 12.5, 25 or 50MBytes/sec speeds. This serial bus defines both a back plane physical layer and a point-to-point cable-connected virtual bus.
7. APPENDIX 7. APPENDIX Glossary Boot Boot means to start the computer operating system by loading it into system memory. When the manual instructs you to “boot” your system (or computer), it means to turn ON your computer. “Reboot” means to restart your computer. When using Windows 95 or later, selecting “Restart” from “Start | Shut Down...” will reboot your computer. Bus Master IDE PIO (Programmable I/O) IDE requires that the CPU be involved in IDE access and waiting for mechanical events.
7. APPENDIX ASUS A7V-E User’s Manual 7 . APPENDIX Glossary LPT Port (Line Printer Port) Logical device name reserved by DOS for the computer parallel ports. Each LPT port is configured to use a different IRQ and address assignment. MMX A set of 57 new instructions based on a technique called Single Instruction, Multiple Data (SIMD), which is built into the new Intel Pentium PP/MT (P55C) and Pentium II (Klamath) CPU as well as other x86-compatible microprocessors.
7. APPENDIX 7. APPENDIX Glossary ROM (Read Only Memory) ROM is nonvolatile memory used to store permanent programs (called firmware) used in certain computer components. Flash ROM (or EEPROM) can be reprogrammed with new programs (or BIOS). SCSI (Small Computer System Interface) High speed multi-threaded I/O interface defined by the X3T9.2 committee of the American National Standards Institute (ANSI) for connecting many peripheral devices.