User Manual
Table Of Contents
- 目錄
- 安全性須知
- 限用物質名稱及含量列表
- 關於這本使用手冊
- K14PA-U12 規格列表
- 第一章:產品介紹
- 第二章:硬體裝置資訊
- 第三章:開啟電源
- 第四章:BIOS 程式設定
- 4.1 管理、更新您的 BIOS 程式
- 4.2 BIOS 設定程式
- 4.3 主選單(Main)
- 4.4 效能調整選單(Performance Tuning menu)
- 4.5 進階選單(Advanced menu)
- 4.5.1 可信賴運算(Trusted Computing)
- 4.5.2 Redfish Host 介面設定(Redfish Host Interface Settings)
- 4.5.3 AMD CBS
- 4.5.4 內建網路設置(Onboard LAN Configuration)
- 4.5.5 UEFI 變量保護(UEFI Variables Protection)
- 4.5.6 序列埠主控台重新導向(Serial Port Console Redirection)
- 4.5.7 CPU 設定(CPU Configuration)
- 4.5.8 PCI 子系統設定(PCI Subsystem Settings)
- 4.5.9 USB 設定(USB Configuration)
- 4.5.10 網路堆疊設定(Network Stack Configuration)
- 4.5.11 NVMe 設定(NVMe Configuration)
- 4.5.12 SATA 設定(SATA Configuration)
- 4.5.13 進階電源管理設定(APM Configuration)
- 4.5.14 AMD 記憶體設定狀態(AMD Mem Configuration Status)
- 4.5.15 T1s Auth
- 4.5.16 第三方 UEFI 驅動程式設定
- 4.5.17 驅動程式狀態(Driver Health)
- 4.6 晶片選單(Chipset menu)
- 4.7 安全性選單(Security menu)
- 4.8 開機選單(Boot menu)
- 4.9 工具選單(Tool menu)
- 4.10 事件記錄選單(Event Logs menu)
- 4.11 伺服器管理選單(Server Mgmt menu)
- 4.12 離開 BIOS 程式(Exit menu)
- 第五章:安裝驅動程式
- 附錄
A-8
附錄
ACTION PHASE POST CODE TYPE DESCRIPTION
PSP Boot
PSP Boot Loader
phase (Status Post
Codes)
0xBB error BIOS load process fully complete
0xBC error Bootloader successfully release x86
0xBD error Early Secure Debug completed
0xBE error GetFWVersion command received from BIOS is completed
0xBF error SMIInfo command received from BIOS is completed
0xC0 error Successfully entered WarmBootResume()
0xC1 error Successfully copied SecureOS image to SRAM
0xC2 error Successfully copied trustlets to PSP Secure Memory
0xC3 error
About to jump to Secure OS (SBL about to copy and jump)
0xC4 error Successfully restored CCP and UMC state on S3 resume
0xC5 error PSP SRAM HMAC validated by Mini BL
0xC6 error About to jump to <t-base in Mini BL
0xC7 error VMG ECDH unit test started
0xC8 error VMG ECDH unit test passed
0xC9 error
VMG ECC CDH primitive unit test started
0xCA
error VMG ECC CDH primitive unit test passed
0xCB error VMG SP800-108 KDF-CTR HMAC unit test started
0xCC error VMG SP800-108 KDF-CTR HMAC unit test passed
0xCD error VMG LAUNCH_* test started
0xCE error VMG LAUNCH_* test passed
0xCF error MP1 has been taken out of reset, and executing SMUFW
0xD0 error PSP and SMU Reserved Addresses correct
0xD1 error Reached Naples steady-state WFI loop
0xD2 error Knoll device successfully initialized
0xD3 error 32-byte RandOut successfully returned from Knoll
0xD4 error 32-byte MAC successfully received from Knoll.
0xD5 error Knoll device veried successfully
0xD6 error CNLI Keys generated and programmed
0xD7 error Enter recovery mode due to trustlet validation fail.
0xD8 error Enter recovery mode due to OS validation fail.
0xD9 error Enter recovery mode due to OEM public key not found.
0xDA error Enter recovery mode with header corruption
0xDB error We should not treat this error as blocking
0xDC error When same fw image type is already loaded in SRAM
0xDD error 0xE2 progress codes are available
0xE0 error Unlock return
0xE2 error Token expiration reset triggered
0xE3 error Completed DXIO PHY SRAM FW key Validation step
0xE4 error MP1 rmware load to SRAM success
(下頁繼續)