Notebook PC Hardware User’s Manual Product Name: Notebook PC Hardware Manual Revision: 1.
Safety Statements Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules.
Safety Statements Nordic Cautions (for Notebook PC with Lithium-Ion Battery) CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. (English) ATTENZIONE! Rischio di esplosione della batteria se sostituita in modo errato. Sostituire la batteria con un una di tipo uguale o equivalente consigliata dalla fabbrica.
Safety Statements Safety Statements WARNING! The following safety precautions will increase the life of the Notebook PC. Follow all precautions and instructions. Except as described in this manual, refer all servicing to qualified personnel. Do not use damaged power cords, accessories, or other peripherals. Do not use strong solvents such as thinners, benzene, or other chemicals on or near the surface. Disconnect the AC power and remove the battery pack(s) before cleaning.
Safety Statements Transportation Precautions To prepare the Notebook PC for transport, you should turn it OFF and disconnect all external peripherals to prevent damage to the connectors. The hard disk drive’s head retracts when the power is turned OFF to prevent scratching of the hard disk surface during transport. Therefore, you should not transport the Notebook PC while the power is still ON.
Safety Statements CTR 21 Approval (for Notebook PC with built-in Modem) Danish Dutch English Finnish French German Greek Italian Portuguese Spanish Swedish 6
Safety Statements UL Safety Notices Required for UL 1459 covering telecommunications (telephone) equipment intended to be electrically connected to a telecommunication network that has an operating voltage to ground that does not exceed 200V peak, 300V peak-to-peak, and 105V rms, and installed or used in accordance with the National Electrical Code (NFPA 70).
Contents 1. Introducing the Notebook PC ................................................................ 11 About This User’s Manual ..................................................................................................... 12 Notes For This Manual ..................................................................................................... 12 2. Knowing the Parts .................................................................................. 13 Top Side ..............................
Contents 4. Using the Notebook PC ......................................................................... 35 Pointing Device ..................................................................................................................... 36 Using the Touchpad ......................................................................................................... 36 Touchpad Usage Illustrations ...........................................................................................
Contents 5. Configuring the BIOS ............................................................................. 59 BIOS Setup Program ............................................................................................................ 60 Updating your BIOS .............................................................................................................. 61 BIOS Menu Bar ................................................................................................................
1.
1 Introducing the Notebook PC About This User’s Manual You are reading the Notebook PC User’s Manual. This User’s Manual provides information on the various components in the Notebook PC and how to use them. The following are major sections of this User’s Manuals: 1. Introducing the Notebook PC Introduces you to the Notebook PC and this User’s Manual. 2. Knowing the Parts Gives you information on the Notebook PC’s components. 3.
2.
2 Knowing the Parts Top Side Refer to the diagram below to identify the components on the top side of the Notebook PC. Display Panel Power Switch / Instant Keys Microphone Keyboard Touchpad Touchpad Buttons CD Control Buttons (see section 3) Status Indicators Opening the Display Panel One spring-loaded latch on the front of the Notebook PC locks the display panel in the closed position when the Notebook PC is not in use.
Knowing the Parts 2 Display Panel The display panel functions the same as a desktop monitor. The Notebook PC uses an active matrix TFT LCD, which provides excellent viewing like that of desktop monitors. Unlike desktop monitors, the LCD panel does not produce any radiation or flickering, so it is easier on the eyes. Display Panel Care The LCD screen is very delicate and requires careful handling.
2 Knowing the Parts Bottom Side Refer to the diagram below to identify the components on the bottom side of the Notebook PC. Reset Button CPU & Memory Compartment Hard Disk Drive Compartment Air Vent & Cooling Fan PUSH Drive Module Eject Name Card Holder L Battery Eject L CD Battery Pack WARNING! The bottom of the Notebook PC can get very hot. Be careful when handling the Notebook PC while it is in operation or recently been in operation.
Knowing the Parts 2 The following describes the components on the bottom side of the Notebook PC as shown by the illustration on the previous page. Hard Disk Drive Compartment The hard disk drive is secured in a compartment under a metal plate. Hard disk drive upgrades are to be done by authorized service centers or dealers only. reset Reset Button The reset button is used for resetting the Notebook PC if or turning OFF the power does not respond.
2 Knowing the Parts Left Side Refer to the diagram below to identify the components on the left side of the Notebook PC. Air Vent 1394 IEEE1394 Fast IrDA PC Card Socket Audio Speaker (Left) IEEE1394 Port IEEE1394 is a high speed serial bus like SCSI but has simple connections and hot-plugging capabilities like USB. The interface IEEE1394 has a bandwidth of 100-400 Mbits/sec and can handle up to 63 units on the same bus.
Knowing the Parts 2 Right Side Refer to the diagram below to identify the components on the right side of the Notebook PC. DCIN Audio Speaker (Right) Optical Drive Eject Head-Out Mic-In DC Power Input Jack Audio Speaker (Right) The built-in speaker allows you to hear audio without additional attachments. The multimedia sound system features an integrated digital audio controller that produces rich, vibrant sound in high quality 16-bit stereo (when used with external stereo headphones or speakers).
2 Knowing the Parts Rear Side Refer to the diagram below to identify the components on the rear side of the Notebook PC. K LAN Port (RJ-45) K Modem Port (RJ-11) Kensington® Lock Port External Expansion Port USB Ports External Monitor Port Parallel Port Air Vent and Cooling Fan Kensington® Lock Port The Kensington® lock port allows the Notebook PC to be secured using Kensington® compatible Notebook PC security products.
Knowing the Parts 2 USB Ports Universal Serial Bus (USB) supports many USB compatible devices such as keyboards, pointing devices, video cameras, modems, hard disk drives, printers, monitors, and scanners connected in a series up to 12Mbits/sec. USB allows up to 127 devices to run simultaneously on a single computer, with peripherals such as USB keyboards and some newer monitors acting as additional plug-in sites or hubs.
2 Knowing the Parts Front Side Refer to the diagram below to identify the components on the front side of the Notebook PC. CD Power LED CD Control Buttons Display Panel Latch Multimedia Power LED and Control Buttons (described in section 3) Display Panel Latch One display panel latch is used to lock the display panel in the closed position. Status Indicators Status indicator details are described in section 3.
3.
3 Getting Started Using the Battery Pack Installing and Removing the Battery Pack Your Notebook PC may or may not have its battery pack installed. If your Notebook PC does not have its battery pack installed, there will be a large opening at the bottom of the Notebook PC. Use the following procedures to install or remove the battery pack. To install the battery pack: Insert the battery pack until it clicks into place. 1 L 1 L PUSH DC IN To remove the battery pack: 1.
Getting Started 3 Charging the Battery Pack Before you use your Notebook PC on the road, you will have to charge the battery pack. The battery pack begins to charge as soon as the Notebook PC is connected to external power. Fully charge the battery pack before using it for the first time. A new battery pack must completely charge before the Notebook PC is disconnected from external power. When the battery power is low, the battery power LED will blink.
3 Getting Started Power Connection Your Notebook PC comes with a universal AC-DC adapter. That means that you may connect the power cord to any 110V-120V as well as 220V-240V outlets without setting switches or using power converters. Different countries may require that an adapter be used to connect the provided US-standard AC power cord to a different standard. Most hotels will provide universal outlets to support different power cords as well as voltages.
Getting Started 3 Powering ON The Notebook PC The Notebook PC’s power-ON message appears on the screen followed by a short beep when you turn it ON. If necessary, you may adjust the brightness by using the hot keys. If you need to run the BIOS Setup to set or modify the system configuration, press [F2] upon bootup to enter the BIOS Setup. If you press [Tab] during the splash screen, standard boot information such as the BIOS version can be seen.
3 Getting Started Power Management - Stand By and Hibernate Power management settings can be found in the Windows control panel. The following shows the power options properties in Windows ME. You can define Stand By or Power Off for closing the display panel, pressing the power button, or activating sleep mode. Basically Stand by and Hibernate saves power when your Notebook PC is not in use by turning OFF certain components.
Getting Started 3 Using the Keyboard Colored Hot Keys The following defines the colored hot keys on the Notebook PC’s keyboard. The colored commands can only be accessed by first pressing and holding the function key while pressing a key with a colored command. NOTE: The Hot Key locations on the function keys may vary depending on model but the functions should remain the same. Follow the icons instead of the function keys (F1, F5, F6, etc.
3 Getting Started Instant Launch Keys and Status Indicators Instant Launch Keys Power Gear The Power Gear button toggles power savings ON or OFF. When power savings is activated, CPU speed and LCD brightness will be decreased. Power Gear will decrease power consumption even more if used together with Intel SpeedStep. Power Gear works only in battery mode and Intel SpeedStep will work in battery or AC mode but requires manual configuration to work in AC mode.
Getting Started 1 3 A Left - Above Keyboard Right - Front Edge Status Indicators Activity Indicator Indicates that the Notebook PC is accessing one or more storage device(s) such as the hard disk or optical storage drive. The light flashes proportional to the access time. 1 Number Lock Indicates that number lock [Num Lk] is activated when lighted. Number lock allows some of the keyboard letters to act as numbers for easier numeric data input.
3 Getting Started Microsoft Windows™ Keys There are two special Windows™ keys on the keyboard as described below. The key with the Windows™ Logo activates the Start menu located at the bottom left of the Windows™ desktop. The other key, that looks like a Windows™ menu with a small cursor, activates the properties menu and is equivalent to pressing the right mouse button on a Windows™ object.
Getting Started 3 Keyboard as Cursors The keyboard can be used as cursors while Number Lock is ON or OFF in order to increase navigation ease while entering numeric data in spreadsheets or similar applications. and one of the cursor keys shown below. For example [Fn][8] for With Number Lock OFF, press up, [Fn][K] for down, [Fn][U] for left, and [Fn][O] for right. With Number Lock ON, use [Shift] and one of the cursor keys shown below.
3 Getting Started Multi-Media Control Buttons and Indicator There are several CD control buttons integrated on the front of the Notebook PC for convenient CD playing. The buttons activate and control your operating system’s audio player when the Notebook PC is ON. When your Notebook PC is OFF, the CD control buttons activate a CD player function that allows you to listen to audio CDs even while the Notebook PC is not turned ON.
4.
4 Using the Notebook PC Pointing Device The Notebook PC’s integrated touchpad pointing device is fully compatible with all two/three-button and scrolling knob PS/2 mice. The touchpad is pressure sensitive and contains no moving parts; therefore, mechanical failures can be avoided. A device driver is still required for working with some application software. See the Driver & Utility Guide for information on drivers and utilities for the touchpad.
Using the Notebook PC 4 Clicking/Tapping - With the cursor over an item, press the left button or use your fingertip to touch the touchpad lightly, keeping your finger on the touchpad until the item is selected. The selected item will change color. The following 2 examples produce the same results.
4 Using the Notebook PC Dragging - Dragging means to pick up an item and place it anywhere on the screen you wish. You can move the cursor over the item you select, and while keeping the left button depressed, moving the cursor to the desired location, then release the button. Or, you can simply double-tap on the item and hold while dragging the item with your fingertip. The following 2 examples produce the same results.
4 Using the Notebook PC Optical Drive Inserting an optical disc 1. While the Notebook PC’s power is ON, press the drive’s eject button and the tray will eject out partially. 2. Gently pull on the drive’s front panel and slide the tray completely out. Be careful not to touch the CD drive lens and other mechanisms. Make sure there are no obstructions that may get jammed under the drive’s tray. 1 A 1 A DCIN DCIN 1 3. Hold the disc by the edge and face the disc’s printed side up.
4 Using the Notebook PC Using the CD-ROM Drive CD-ROM discs and equipment must be handled with care because of the precise mechanics involved. Keep in mind the important safety instructions from your CD suppliers. Unlike desktop CD-ROM drives, the Notebook PC uses a hub to hold the CD in place regardless of the angle. When inserting a CD, it is important that the CD be pressed onto the center hub or else the CD-ROM drive tray will scratch the CD.
Using the Notebook PC 4 Regional Playback Information Playback of DVD movie titles involves decoding MPEG2 video, digital AC3 audio and decryption of CSS protected content. CSS (sometimes called copy guard) is the name given to the content protection scheme adopted by the motion picture industry to satisfy a need to protect against unlawful content duplication. Although the design rules imposed on CSS licensors are many, one rule that is most relevant is playback restrictions on regionalized content.
4 Using the Notebook PC Optional External Connections Monitor Out Connection K Connecting an external monitor is just like on a standard desktop PC. Just plug in the VGA cable and its ready to use (some Notebook PC configurations may require additional display driver settings). You can view the Notebook PC display panel while simultaneously allowing others to view the external monitor. For large audiences, try connecting a computer video projector.
Using the Notebook PC 4 Optional External Connections (Cont’) External Audio Connections The Notebook PC provides easy access for connecting a stereo headphone, mono microphone, and a stereo audio source just like on some personal tape recorders. 1 A DCIN IEEE1394 Connection IEEE1394 is a high speed serial bus like SCSI but has simple connections and hot-plugging capabilities like USB.
4 Using the Notebook PC Optional External Connections (Cont’) USB ports are provided on both the left and rear sides for connection to USB devices. External Keyboard Connection To allow easier data entry, you may connect any PS/2 or USB (shown here) keyboard. K External Mouse Connection A USB mouse can be easily connected to the Notebook PC. The USB mouse will work simultaneously with the Notebook PC’s touchpad.
Using the Notebook PC 4 USB Floppy Disk Drive (Optional) The Notebook PC features an optional USB-interface disk drive that accepts a standard 1.44MB (or 720KB) 3.5-inch floppy diskette. The eject button is on the top edge of the floppy disk drive for easy access, unlike desktop PCs with the eject button on the bottom of the floppy disk drive. Floppy access activity can be monitored through the LED on the front of the floppy disk drive. Connection Connection is very easy because of USB technology.
4 Using the Notebook PC PortBar II Accessory (Optional) If you require a simple inexpensive docking solution, just use a PortBar to connect your desktop devices and then quickly connect or disconnect all the devices through a single easy-to-use connector. The PortBar’s Plug & Play feature allows it to be connected or disconnected while the Notebook PC is ON or OFF (hot-dockable). Except for the device connected to the serial port, other devices should function normally while hot-dockable.
Using the Notebook PC 4 PC Card (PCMCIA) Socket The Notebook PC supports PC Cards (or sometimes referred to as PCMCIA cards) to allow expansion like PCI cards on desktop computers. This allows you to customize your Notebook PC to meet a wide range of application needs. The PCMCIA socket can interface with type I or type II PC cards. PC cards are about the size of a few stacked credit cards and have a 68-pin connector at one end.
4 Using the Notebook PC Inserting a PC Card (PCMCIA) 1. Insert the PC card with the connector side first. When the PC card is fully inserted, the PC card bay door can close normally without striking the PC card. 2. Carefully connect any cables or adapters needed by the PC card. Usually connectors can only be inserted in one orientation. Look for a sticker, icon, or marking on one side of the connector representing the top side.
Using the Notebook PC 4 Modem and Network Connections The built-in modem and network model comes with both an RJ-11 and an RJ-45 port. RJ-11 telephone cables have two or four wires and are used to connect telephones to telephone outlets found in the walls of residential homes and some commercial buildings (some commercial buildings may have telephone wiring designed for dedicated phone systems that may not be compatible).
4 Using the Notebook PC Network Connection Connect a network cable, with RJ-45 connectors on each end, to the modem/network port on the Notebook PC and the other end to a hub or switch. For 100BASE-TX speeds, your network cable must be category 5 (not category 3) with twisted-pair wiring. If you plan on running the interface at 100Mbps, it must be connected to a 100BASE-TX hub (not a 100BASE-T4 hub). For 10Base-T, use category 3, 4, or 5 twisted-pair wiring.
Using the Notebook PC 4 IR Wireless Communication The Notebook PC is equipped with a conveniently located Infrared (IR) Communication Port (see 2. Knowing the Parts for location). The IR port comes with IrDA (Infrared Data Association) Serial Infrared Data Link Version 1.1 compliance, that allows you to perform point-to-point wireless communications. You can use a FIR-specified application to transmit or receive data files with other systems equipped with an infrared port.
4 Using the Notebook PC CAUTION! Disable the infrared communication when you are not using the IR for long periods because the IR consumes a great deal of Windows resources which will decrease the Notebook PC’s performance. AC Power System The Notebook PC power is comprised of two parts, the power adapter and the battery power system. The power adapter converts AC power from a wall outlet to the DC power required by the Notebook PC. The battery pack consists of a set of battery cells housed together.
Using the Notebook PC 4 Using Battery Power A fully-charged battery pack provides the Notebook PC a few hours of working power. But the actual figure varies depending on how you use the power saving features, your general work habits, the CPU, system memory size, and the size of the display panel. Checking Battery Power To check the remaining battery power, move your cursor over the power icon. The power icon is a “battery” when not using AC power and a “plug” when using AC power.
4 Using the Notebook PC Power Management Modes The Notebook PC has a number of automatic or adjustable power saving features that you can use to maximize battery life and lower Total Cost of Ownership (TCO). You can control some of these features through the Power menu in the BIOS Setup. ACPI power management settings are made through the operating system.
Using the Notebook PC 4 Power Savings In addition to reducing the CPU clock, this mode puts devices including the LCD backlight in their lower active state. The Notebook PC enters Standby mode (low priority) when the system remains idle for a specified amount of time. The timeout can be set through BIOS setup (lower priority) and Windows power management (higher priority). To resume system operation, press any key.
4 Using the Notebook PC System Memory Expansion Optional memory is not required to use this Notebook PC. Additional memory will increase application performance by decreasing hard disk access. This is more noticeable on newer software that require more and more system resources. The Notebook PC comes with either 128MB or 256MB built-in memory. One standard 144-pin SO-DIMM (Small Outline Dual Inline Memory Module) socket is available for system memory expansion using a common 3.
Using the Notebook PC 4 Vehicle/Air & Vehicle-Only Power Adapters (Optional) The main purpose of the vehicle/air or vehicle-only power adapters is to provide a source of power for using the Notebook PC and/or charging the Notebook PC’s battery from while in transit when no AC power is available. These products are essential tools for today’s mobile professional.
4 Using the Notebook PC Securing Your Notebook PC (Optional) For system and hard disk drive security, see BIOS setup “Security”. A third party lock such as the ones by Kensington® can be used to secure your Notebook PC physically to an unmovable object. The cable wraps around an object and the “T” shaped end inserts into the Kensington® lock port as shown in this illustration and a key or combination dial is used to secure the lock in place.
5.
5 Configuring the BIOS BIOS Setup Program This Notebook PC supports a programmable EEPROM that stores the BIOS software and can be updated using the provided flash memory writer utility. This Section will guide you through the BIOS setup program by providing clear explanations for all the options. A default configuration has already been set. If you are either installing new devices or expanding main memory, you will need to enter the BIOS Setup to reconfigure your Notebook PC.
Configuring the BIOS 5 Updating your BIOS This Notebook PC supports an easy-to-use BIOS update software called “WINFLASH” which is installed through the provided support CD. If you need help installing or using “WINFLASH”, refer to the “Driver & Utility Manual”. BIOS Menu Bar The top of the screen has a menu bar with the following selections: MAIN Use this menu to make changes to the basic system configuration.
5 Configuring the BIOS General Help In addition to the Item Specific Help window, the BIOS setup program also provides a General Help screen. This screen can be called up from any menu by simply pressing [F1] or the [Alt] + [H] combination. The General Help screen lists the legend keys with their corresponding alternates and functions. Scroll Bar When a scroll bar appears to the right of a help window, it indicates that there is more information to be displayed that will not fit in the window.
Configuring the BIOS 5 Main Menu When the Setup program is accessed, the main menu screen appears as shown: Item Specific Help System Time System Date Legacy Diskette A [17:15:00] [02/19/2002] [1.44M, 3.5 in.] Primary Master Primary Slave Secondary Master Secondary Slave [Auto] [Auto] [Auto] [Auto] Video Display Device Installed Memory [LCD & CRT] 128 MB BIOS Revision 0201 to select field; <+>,<-> to change value.
5 Configuring the BIOS Video Display Device [LCD & CRT] This field allows you to select and enable video display devices, such as an LCD panel, an external CRT/LCD monitor, or both. The configuration options are: [LCD & CRT] [LCD] [CRT] Installed Memory [128 MB] (display field) This field displays the amount of extended memory as detected by the system. Unfortunately, this will not tell you how much is onboard and how much is added to the SO-DIMM socket.
Configuring the BIOS 5 Primary Master (sub-menu) This field is used to configure the primary IDE drive installed in the system. To configure a hard disk drive, select this sub-menu from the Main menu and press the Enter key to enter this sub-menu.
5 Configuring the BIOS Cylinders [ ] This field configures the number of cylinders. Refer to your drive documentation to determine the correct value to enter into this field. NOTE: To make changes to this field, the Type field must be set to User Type HDD and “Translation Method” must be set to Manual. Heads [ ] This field configures the number of read/write heads. Refer to your drive documentation to determine the correct value to enter into this field.
Configuring the BIOS 5 Ultra DMA Mode [ ] This field auto detects Ultra DMA capability (for improved transfer speeds and data integrity) for compatible IDE (Integrated Disk Electronics) devices. Set to Disable to suppress Ultra DMA capability. NOTE: To make changes to this field, the Type field must be set to User Type HDD. The configuration options are: [0] [1] [2] [3] [4] [5] [Disabled]. The following is for your reference: Mode 0 = 16.7MB/s Mode 2 = 33.3MB/s (ATA/33) Mode 4 = 66.
5 Configuring the BIOS Advanced Menu Selecting Advanced from the main menu bar display the Advanced menu as shown below. Item Specific Help I/O Device Configuration Internal Pointing Device Quick Power On Self Test [Enabled] [Enabled] to go to the sub-menu. >I/O Device Configuration (described on next page) Pressing [Enter] when this field is highlighted calls up a sub-menu for configuring the Notebook PC’s serial and parallel ports.
Configuring the BIOS 5 I/O Device Configuration (sub-menu) I/O Device Configuration IR Port Mode DMA Channel [2F8H/IRQ3] [FIR] [1] Parallel Port Mode ECP DMA Select [378H/IRQ7] [ECP+EPP] [3] Item Specific Help to select the I/O Address & IRQ for Infrared. NOTE: The presence of sub-items in this menu is dependent on certain relevant settings.
5 Configuring the BIOS Parallel Port: [378H/IRQ7] This field allows you to configure the Notebook PC parallel port. The configuration options are: [Disabled] [378H/IRQ7] [278H/IRQ5] Mode: [ECP+EPP] This field allows you to configure the Notebook PC parallel port transmission mode. The configuration options are: [Normal] [EPP] [ECP] [ECP+EPP] EPP Mode: When the EPP mode is selected, the standard and bidirectional modes are also available. The EPP operates on a two phase cycle.
Configuring the BIOS 5 Security Menu The Notebook PC’s advanced system of security allows you to set a password to prevent unauthorized access to system resources, data, and the BIOS Setup Program. This Section covers each parameter of the Security Setup. Selecting Security from the menu bar displays the following menu: Item Specific Help System Password Password on boot [Enter] [Disabled] Hard disk Password [Enter] Supervisor password controls full access.
5 Configuring the BIOS System Password [Enter] The system password protects the BIOS settings. When “Enabled”, you will be prompted for a password after you press [F2] to enter BIOS setup. To Enable: Select “Enter” and press [Enter], type a password and press [Enter], type the same password again and press [Enter] to confirm. (You can type up to eight alphanumeric characters. Symbols and other keys are ignored.) To Disable: Select “Set” and press [Enter] without entering a password.
Configuring the BIOS 5 Power Menu The power management settings are controlled by the operating system. This menu only has one function as follows: Item Specific Help LCD auto power saving [Enabled] Start Battery Refreshing By slowing down CPU speed when AC adapter not in use to conserve battery power LCD Auto Power Saving [Enabled] Enabling this item will decrease the LCD brightness when the AC power is not connected in order to conserve battery power.
5 Configuring the BIOS Boot Menu The Boot menu allows the user to specify the order in which the Notebook PC is to check for a device to boot the system. To make changes, select Boot from the menu bar and the following screen appears: Item Specific Help 1. Removable Device 2. IDE Hard Drive 3. ATAPI CD-ROM 4. Other Boot Device Onboard LAN Boot ROM [Legacy Floppy] [IC25N030ATDA04-0] [TOSHIBA DVD-ROM SD-R2102] [INT18 Device (Network)] [Disabled] Boot Sequence: to select the device.
Configuring the BIOS 5 Exit Menu Once you have made all of your selections from the various menus in the Setup program, you should save your changes and exit Setup. Select Exit from the menu bar to display the following menu: Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes Exit setup utility and save your changes to CMOS. NOTE: Pressing the [Esc] key does not exit this menu.
5 Configuring the BIOS Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When this option is selected or if [F9] is pressed, a confirmation is requested. Select Yes to load default values programmed into the BIOS file (the default values may change from one BIOS version to another). You can now select Exit Saving Changes or make other changes before saving the values to the EEPROM.
Appendix Internal Modem Compliancy Glossary Index Owner Information 77
A Appendix Internal Modem Compliancy The Notebook PC with internal modem model complies with JATE (Japan), FCC (US, Canada, Korea, Taiwan), and CTR21. The internal modem has been approved in accordance with Council Decision 98/ 482/EC for pan-European single terminal connection to the public switched telephone network (PSTN).
Appendix A This table shows the countries currently under the CTR21 standard.
A Appendix Glossary ACPI (Advanced Configuration and Power Management Interface) Modern standard for reducing power usage in computers. APM (Advanced Power Management) Modern standard for reducing power usage in computers. AWG (American Wire Gauge) Gauge AWG Diam (mm) Area (mm2) R (ohm/km) I@3A/mm2 (mA) Gauge AWG Diam (mm) Area (mm2) R (ohm/km) I@3A/mm2 (mA) 46 0.04 0.0013 13700 3.8 24 0.50 0.20 87.5 588 44 0.05 0.0020 8750 6 0.55 0.24 72.3 715 42 41 0.06 0.07 0.0028 0.
Appendix A BIOS (Basic Input/Output System) BIOS is a set of routines that affect how the computer transfers data between computer components, such as memory, disks, and the display adapter. The BIOS instructions are built into the computer’s read-only memory. BIOS parameters can be configured by the user through the BIOS Setup program. The BIOS can be updated using the provided utility to copy a new BIOS file into the EEPROM. Bit (Binary Digit) Represents the smallest unit of data used by the computer.
A Appendix IDE (Integrated Drive Electronics) IDE devices integrate the drive control circuitry directly on the drive itself, eliminating the need for a separate adapter card (in the case for SCSI devices). UltraDMA/66 or 100 IDE devices can achieve up to 33MB/Sec transfer. IEEE1394 Also known as iLINK (Sony) or FireWire (Apple). IEEE1394 is a high speed serial bus like SCSI but has simple connections and hot-plugging capabilities like USB.
Appendix A POST (Power On Self Test) When you turn on the computer, it will first run through the POST, a series of software-controlled diagnostic tests. The POST checks system memory, the motherboard circuitry, the display, the keyboard, the diskette drive, and other I/O devices. PS/2 Port PS/2 ports are based on IBM Micro Channel Architecture. This type of architecture transfers data through a 16-bit or 32-bit bus. A PS/2 mouse and/or keyboard may be used on ATX motherboards.
A 84 Appendix
Appendix A Index A C AC Power System 52 APM and ACPI 54 Canadian Department of Communications 2 Capital Lock 31 CardBus 47 CDRH Regulations 3 Colored Hot Keys 29 Cooling Fan 17, 21 CTR 21 Approval 6 B Battery Pack 24 Battery Power System 52 BIOS Advanced Menu 68 BIOS Legend Bar 61 BIOS Menu Bar 61 BIOS Setup Program 60 Boot Menu 74 Boot Sequence 74 Cylinders 66 Discard Changes 76 DMA Channel 70 Exit Discarding Changes 75 Exit Menu 75 Exit Saving Changes 75 Heads 66 I/O Device Configuration 69 IR Port
A Appendix K R Keyboard 15 Regional Playback Information 41 Restarting or Rebooting 28 M Macrovision Notice 3 Microsoft Windows™ Keys 32 Modem and Network Connections 49 Modem Port 20 Monitor Out Connection 42 Mouse or Keyboard Connection 44 N Securing Your Notebook PC 58 Status Indicators 30 Suspend Mode 54, 83 System Memory Expansion 57 T O Thermal Power Control 55 Touchpad and Buttons 15 Touchpad, Caring 38 Touchpad, Using 36 Transportation Precautions 5 Twisted-Pair Cable 50, 83 Owner Inform
Appendix A 87
A Appendix Owner Information This page is provided for recording information concerning your Notebook PC for future reference or for technical support. Keep this User’s Manual in a secured location if passwords are filled out.
