Deluxe Motherboard M2N-SLI
E2590 First Edition May 2006 Copyright © 2006 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Notices......................................................................................................... vii Safety information..................................................................................... viii About this guide.......................................................................................... ix M2N-SLI Deluxe specifications summary.................................................. xi Chapter 1: Product introduction 1.1 Welcome!.............................
Contents 2.6 2.7 Jumper......................................................................................... 2-20 Connectors.................................................................................. 2-21 2.7.1 2.7.2 Rear panel connectors................................................... 2-21 Internal connectors........................................................ 2-24 Chapter 3: Powering up 3.1 3.2 Starting up for the first time.........................................................
Contents 4.4 4.3.8 Usable Memory.............................................................. 4-18 4.4.1 JumperFree Configuration............................................. 4-19 4.4.3 PEG Link Mode.............................................................. 4-22 Advanced menu.......................................................................... 4-19 4.4.2 4.4.4 4.4.5 4.4.6 4.5 4.4.7 PCIPnP..........................................................................
Contents 5.3 5.2.7 Other information............................................................. 5-6 5.3.1 Cool ‘n’ Quiet!™ Technology............................................ 5-8 5.3.3 ASUS Music Alarm......................................................... 5-17 Software information.................................................................... 5-8 5.3.2 5.3.4 5.3.5 5.3.6 5.4 ASUS AI Nap................................................................. 5-20 ASUS AI Gear...................
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • • • • • • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This guide contains the following parts: • • • • • • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports. Chapter 2: Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components.
Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Instructions that you MUST follow to complete a task. NOTE: Tips and additional information to help you complete a task.
M2N-SLI Deluxe specifications summary CPU Socket AM2 for AMD Athlon™ 64 X2 /AMD Athlon™ 64 /AMD Athlon™ 64 FX/AMD Sempron™ processors Supports AMD Cool ‘n’ Quiet™ Technology AMD64 architecture enables simultaneous 32-bit and 64-bit computing AMD Live!™ ready Chipset NVIDIA® nForce® 570 SLI™ MCP System bus 2000 / 1600 MT/s Memory Dual-channel memory architecture - 4 x 240-pin DIMM sockets support unbuffered ECC/non-ECC DDR2 800/667/533 MHz memory modules - Supports up to 8 GB system memory Expa
M2N-SLI Deluxe specifications summary High Definition Audio SoundMAX® ADI AD1988B 8-channel CODEC Supports Jack-Sensing, Enumeration, Multi-Streaming, and Jack-Retasking Technology Optical and Coaxial S/PDIF Out interfaces IEEE 1394 T1 1394 controller supports: - 2 x IEEE 1394a connectors (one at mid-board, one at the rear panel) USB Supports up to 10 USB 2.0/1.
M2N-SLI Deluxe specifications summary Rear panel 1 x PS/2 keyboard port (purple) 1 x PS/2 mouse port (green) 1 x Serial (COM1) port 1 x IEEE 1394a port 1 x External Serial ATA port 1 x Optical S/PDIF Out port 1 x Coaxial S/PDIF Out port 2 x LAN (RJ-45) ports 4 x USB 2.0/1.1 ports 8-channel audio ports Internal connectors 3 x USB 2.0 connectors support six additional USB 2.
xiv
This chapter describes the motherboard features and the new technologies it supports.
Chapter summary 1 1.1 Welcome!....................................................................................... 1-1 1.3 Special features............................................................................. 1-2 1.2 Package contents..........................................................................
1.1 Welcome! Thank you for buying an ASUS® M2N-SLI Deluxe motherboard! The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your motherboard package for the following items. Motherboard ASUS M2N-SLI Deluxe I/O modules IEEE 1394a module 1 x 2-port USB 2.
1.3 Special features 1.3.1 Product highlights Latest processor technology The motherboard comes with a 940-pin AM2 socket that supports AMD Athlon™ 64 X2/AMD Athlon™ 64/AMD Athlon™ 64 FX/AMD Sempron™ processors. With an integrated low-latency high-bandwidth memory controller and a highly scalable HyperTransport™ technology-based system bus, the motherboard provides a powerful platform for your diverse computing needs, increased office productivity, and enhanced digital media experience.
Serial ATA I/II technology and SATA-On-The-Go The motherboard fully supports the Serial ATA II 3.0 Gb/s technology through the Serial ATA interfaces and the NVIDIA® nForce® 570 SLI™ chipset. The Serial ATA 3 Gb/s specification provides twice the bandwidth of the current Serial ATA products with a host of new features, including Nativa Command Queueing (NCQ), and Power Management (PM) Implementation Algorithm.
AMD Cool ‘n’ Quiet Technology The motherboard supports the AMD Cool ‘n’ Quiet Technology, which monitors system operation and automatically adjusts CPU voltage and frequency for a cool and quiet operating environment. See page 4-26 for details. 1.3.2 ASUS AI Lifestyle features AI Gear AI Gear provides four modes that adjust the CPU frequency and Vcore voltage minimizing system noise and power consumption. You can choose the mode that best suits your computing needs.
Advanced Thermal Design Fanless Design and Heat-pipe The ASUS fanless design allows multi-directional heat flow from major thermal sources in the motherboard to lower overall system temperature, resulting in quieter operation and longer system life. ASUS has devoted special efforts to address the thermal issues across the motherboard, and most notably in the following areas: CPU, power, VGA, and chipset.
Precision Tweaker This feature allows you to fine tune the CPU/memory voltage and gradually increase the memory Front Side Bus (FSB) and PCI Express frequency at 1MHz increment to achieve maximum system performance. C.P.R. (CPU Parameter Recall) The C.P.R. feature of the motherboard BIOS allows automatic re-setting to the BIOS default settings in case the system hangs due to overclocking. When the system hangs due to overclocking, C.P.R.
This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
Chapter summary 2 2.1 Before you proceed...................................................................... 2-1 2.3 Central Processing Unit (CPU).................................................... 2-6 2.2 2.4 2.5 2.6 2.7 Motherboard overview.................................................................. 2-2 System memory.......................................................................... 2-11 Expansion slots...........................................................................
2.1 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Use a grounded wrist strap or touch a safely grounded object or to a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity. • Hold components by the edges to avoid touching the ICs on them.
2.2 Motherboard overview Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components. 2.2.1 Placement direction When installing the motherboard, make sure that you place it into the chassis in the correct orientation.
2.2.3 Motherboard layout 24.5cm (9.6in) PWR_FAN ATX12V CPU_FAN Super I/O SPDIF_O1 AUDIO FLOPPY EATXPWR CHA_FAN1 CHA_FAN2 LAN2_USB34 DDR2 DIMM_A2 (128 bit,240-pin module) Socket AM2 LAN1_USB12 DDR2 DIMM_A1 (128 bit,240-pin module) LPT ESATA_1394 DDR2 DIMM_B2 (128 bit,240-pin module) DDR2 DIMM_B1 (128 bit,240-pin module) COM1 SPDIF_O2 USB910 PCIEX1_1 Marvell 88E1116 JMicron JMB363 SATA_RAID1 PRI_IDE 30.5cm (12.
2.2.4 2- Layout contents Slots 1. 2. 3. 4. DDR2 DIMM slots PCI slots PCI Express x1 slots PCI Express x16 slots Page 2-11 2-17 2-18 2-18 Jumper 1. Clear RTC RAM (3-pin CLRTC) Page 2-20 Rear panel connectors 1. PS/2 mouse port (green) 2. Serial (COM) port 3. IEEE 1394a port 4. LAN 1 (RJ-45) port. 5. LAN 2 (RJ-45) port. 6. Rear Speaker Out port (black) 7. Center/Subwoofer port (orange) 8. Line In port (light blue) 9. Line Out port (lime) 10. Microphone port (pink) 11.
Internal connectors 1. Floppy disk drive connector (34-1 pin FLOPPY) 2. IDE connector (40-1 pin PRI_IDE) 3. NVIDIA® nForce 570 SLI Serial ATA connectors (7-pin SATA1 [red], SATA2 [red], SATA3 [red], SATA4 [red], SATA5 [red], SATA6 [red]) 4. JMicron® Serial ATA RAID connector (7-pin SATA_RAID1) Page 2-24 2-24 2-25 5. 6. 7. 2-27 2-27 2-28 8. 9. 10. 11. 12. 13. 14.
2.3 Central Processing Unit (CPU) The motherboard comes with a 940-pin AM2 socket designed for the AMD Athlon™ 64/AMD Athlon™ 64 FX/AMD Athlon™ 64 X2 and AMD Sempron™ processors. The AM2 socket has a different pin layout from the 940-pin socket designed for the AMD AM2 processor. Make sure you use a CPU is designed for the AM2 socket. The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU! 2.3.
3. 4. Position the CPU above the socket such that the CPU corner with the gold triangle matches the socket corner with a small triangle. Carefully insert the CPU into the socket until it fits in place. Gold triangle Small triangle 5. 6. When the CPU is in place, push down the socket lever to secure the CPU. The lever clicks on the side tab to indicate that it is locked. Install a CPU heatsink and fan following the instructions that came with the heatsink package.
2.3.2 Installing the heatsink and fan The AMD Athlon™ 64/AMD Athlon™ 64 FX/AMD Athlon™ 64 X2 and AMD Sempron™ processors require a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. Make sure that you use only AMD-certified heatsink and fan assembly. To install the CPU heatsink and fan: 1. Place the heatsink on top of the installed CPU, making sure that the heatsink fits properly on the retention module base.
2. Attach one end of the retention bracket to the retention module base. 3. Align the other end of the retention bracket (near the retention bracket lock) to the retention module base. A clicking sound denotes that the retention bracket is in place. Make sure that the fan and heatsink assembly perfectly fits the retention mechanism module base, otherwise you cannot snap the retention bracket in place. 4.
5. When the fan and heatsink assembly is in place, connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN. M2N-SLI DELUXE CPU FAN PWM CPU FAN IN CPU FAN PWR GND CPU_FAN R M2N-SLI DELUXE CPU Fan Connector 2-10 • Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector. • This connector is backward compatible to the 3-pin CPU fan connector..
2.4 System memory 2.4.1 Overview The motherboard comes with four Double Data Rate 2 (DDR2) Dual Inline Memory Modules (DIMM) sockets. A DDR2 module has the same physical dimensions as a DDR DIMM but has a 240-pin footprint compared to the 184-pin DDR DIMM. DDR2 DIMMs are notched differently to prevent installation on a DDR DIMM socket.
* For dual-channel memory configuration (2), you may: • install identical DIMMs in all four sockets OR • install an identical DIMM pair in DIMM_A1 and DIMM_B1 (yellow sockets) and another identical DIMM pair in DIMM_A2 and DIMM_B2 (black sockets) * Always use identical DDR2 DIMM pairs for dual-channel model. For optimum compatibility, we recommend that you obtain memory modules from the same vendor. Visit the ASUS website (www.asus.com) for the latest Qualified Vendors List.
Qualified Vendors List DDR2-667 DDR2 Size Vendor Model Side(s) Component DIMM socket support A* B* C* 512MB KINGSTON E5108AE-6E-E SS KVR667D2N5/512 • • • 1024MB KINGSTON E5108AE-6E-E DS KVR667D2N5/1G • 512MB KINGSTON E5108AE-6E-E SS KVR667D2E5/512 • 256MB KINGSTON HYB18T256800AF3 SS KVR667D2N5/256 • • • 256MB SAMSUNG K4T56083QF-ZCE6 SS M378T3253FZ0-CE6 • • • 256MB SAMSUNG K4T51163QC-ZCE6 SS M378T3354CZ0-CE6 • • • 512MB SAMSUNG ZCE6K4T51083QC SS M378T65
Qualified Vendors List DDR2-800 DDR2 Size Vendor Side(s) Model Component DIMM socket support A* B* C* 512MB KINGSTON K4T51083QC SS KVR800D2N5/512 • • • 1024MB KINGSTON K4T51083QC DS KVR800D2N5/1G • • • 512MB Infineon HYB18T256800AF25F DS HYS64T64020HU-25F-A • • • 512MB Hynix HY5PS12821BFP-S5 SS HYMP564U64BP8-S5 • • 512MB MICRON 5JAIIZ9DQQ SS MT8HTF6464AY-80EA3 • • 512MB MICRON 5ZD22D9GKX SS MT8HTF6464AY-80ED4 • • 512MB MICRON 6CD22D9GKX SS MT8HTF6464A
2.4.3 Installing a DIMM Unplug the power supply before adding or removing DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components. 2 To install a DIMM: 1. 2. 3. 3 Unlock a DIMM socket by pressing the retaining clips outward. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket.
2.5 Expansion slots In the future, you may need to install expansion cards. The following sub‑sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. 2.5.1 Installing an expansion card To install an expansion card: 1. 2. 3. 4. 5. 6.
2.5.
2.5.5 PCI Express x1 slot This motherboard supports PCI Express x1 network cards, SCSI cards and other cards that comply with the PCI Express specifications. Refer to the figure below for the location of the slot. 2.5.6 PCI Express x16 slots This motherboard supports PCI Express x16 graphics cards that comply with the PCI Express specifications. Refer to the figure below for the location of the slots.
Recommended PCI Express x16 configurations PCIEX16_1 (Blue) slot Mode Non-SLI mode PCIE16_2 (Black) slot Card type Speed PCIe x16 graphics card x16 NA PCIe x16 graphics card x16 PCIe x16 graphics card x8 PCIe x16 graphics card x16 Other PCIe devices x8, x4, x1 Dual graphics card in SLI Mode ASUS M2N-SLI Deluxe Card type Speed Two identical NVIDIA® SLI™ Edition graphics cards at x8, x8 speed 2-19
2.6 Jumper Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the onboard battery. 3. Move the jumper cap from pins 1-2 (default) to pins 2-3.
2.7 Connectors 2.7.1 Rear panel connectors 3 2 1 4 5 6 7 8 9 16 1. 2. 3. 4. 5. 15 14 13 12 11 10 PS/2 mouse port (green). This port is for a PS/2 mouse. Serial port. This 9-pin COM1 port is for pointing devices and other serial devices. IEEE 1394a port. This 6-pin IEEE 1394a port provides high-speed connectivity for audio/video devices, storage peripherals, PCs, or portable devices. LAN 1 (RJ-45) port.
9. Line Out port (lime). This port connects a headphone or a speaker. In 4-channel, 6-channel, and 8-channel configuration, the function of this port becomes Front Speaker Out. 10. Microphone port (pink). This port connects a microphone. 11. Side Speaker Out port (gray). This port connects the side speakers in an 8-channel audio configuration. Refer to the audio configuration table below for the function of the audio ports in 2, 4, 6, or 8-channel configuration.
• If you intend to create a RAID configuration using this connector, set the JMicron JMB363 controller item in the BIOS to [IDE]. See section “4.4.7 Onboard Device Configuration” for details. • Use these ports and an external Serial ATA box connected to the external SATA port, if you want to configure a RAID 0 or RAID 1 set. • The Serial ATA port multiplier and external Serial ATA box are purchased separately. • DO NOT insert a different connector to this port.
2.7.2 1. Internal connectors Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. Pin 5 on the connector is removed to prevent incorrect cable connection when using a FDD cable with a covered Pin 5. PIN 1 M2N-SLI DELUXE R FLOPPY NOTE: Orient the red markings on the floppy ribbon cable to PIN 1.
If any device jumper is set as “Cable-Select,” make sure all other device jumpers have the same setting. M2N-SLI DELUXE PRI_IDE R M2N-SLI DELUXE IDE Connector 3. NVIDIA® nForce® 570 SLI MCP Serial ATA connectors (7-pin SATA1 [red], SATA2 [red], SATA3 [red], SATA4 [red], SATA5 [red], SATA6 [red]) These connectors are for the Serial ATA signal cables for Serial ATA 3.0 Gb/s hard disk and optical disk drives. The Serial ATA 3.0 Gb/s is backward compatible with Serial ATA 1.5 Gb/s specification.
Connect the right-angle side of the SATA signal cable to the SATA device or you may connect the right-angle side of the SATA cable to the onboard SATA port to avoid placement conflict with huge graphics cards. 4. right angle side JMicron JMB363® Serial ATA RAID connector (7-pin SATA_RAID1) This connector is for a Serial ATA signal cable. This connector supports a Serial ATA hard disk drive that you can configure for RAID through the onboard Serial ATA RAID controller.
USB connectors (10-1 pin USB56, USB78, USB910) These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed. 1 USB+5V USB_P9USB_P9+ GND USB910 USB+5V USB_P10USB_P10+ GND NC 5. M2N-SLI DELUXE 1 1 USB+5V USB_P7USB_P7+ GND M2N-SLI DELUXE USB 2.
7. CPU, chassis, and power fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN1, 3-pin CHA_FAN2, 3-pin CHA_FAN3, 3-pin CHA_FAN4, 3-pin PWR_FAN) The fan connectors support cooling fans of 350 mA ~ 2000 mA (24 W max.) or a total of 1 A ~ 3.48 A (41.76 W max.) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors.
8. Chassis intrusion connector (4-1 pin CHASSIS) This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. The signal is then generated as a chassis intrusion event.
• For a fully configured system, we recommend that you use a power supply unit (PSU) that complies with ATX 12 V Specification 2.0 (or later version) and provides a minimum power of 600 W. • Do not forget to connect the 4-pin ATX +12 V power plug; otherwise, the system will not boot. • Use of a PSU with a higher power output is recommended when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate. 10.
Optical drive audio connector (4-pin CD) This connector allows you to receive stereo audio input from an optical drive such as DVD or CD-ROM.. M2N-SLI DELUXE CD (black) R Right Audio Channel Ground Ground Left Audio Channel 11. M2N-SLI DELUXE Internal Audio Connector 12. Parallel port connector (26-1 pin LPT) This connector is for a parallel port. Connect the parallel port module cable to this connector, then install the module to a slot opening at the back of the system chassis.
13. Digital audio connector (4-1 pin SPDIF_OUT) R SPDIFOUT GND M2N-SLI DELUXE +5V This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port(s). Connect the S/PDIF In/Out module cable to this connector, then install the module to a slot opening at the back of the system chassis. SPDIF_OUT M2N-SLI DELUXE Digital Audio Connector The S/PDIF module is purchased separately.
14. System panel connector (20-8 pin PANEL) This connector supports several chassis-mounted functions.
Q-Connector (System panel) ASUS Q-Connector allows you to easily to connect the chassis front panel cables to the motherboard. Perform these steps to install ASUS Q-Connector. Step 1 Connect the front panel cables to their respective connectors on the ASUS Q-Connector. Refer to the labels on the Q-Connector for proper connection and pin definition. Step 2 Carefully connect the ASUS Q-Connector to the System panel connector.
This chapter describes the power up sequence and ways of shutting down the system.
Chapter summary 3.1 3.2 3 Starting up for the first time......................................................... 3-1 Powering off the computer...........................................................
3.1 Starting up for the first time 1. After making all the connections, replace the system case cover. 3. Connect the power cord to the power connector at the back of the system chassis. 2. 4. 5. Be sure that all switches are off. Connect the power cord to a power outlet that is equipped with a surge protector. Turn on the devices in the following order: a. Monitor c. System power b. 6. 7.
3.2 Powering off the computer 3.2.1 Using the OS shut down function If you are using Windows® 2000: 1. 2. 3. Click the Start button then click Shut Down... Make sure that the Shut Down option button is selected, then click the OK button to shut down the computer. The power supply should turn off after Windows® shuts down. If you are using Windows® XP: 1. Click the Start button then select Turn Off Computer. 3. The power supply should turn off after Windows® shuts down. 2.
This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
Chapter summary 4 4.1 Managing and updating your BIOS............................................. 4-1 4.3 Main menu................................................................................... 4-14 4.2 4.4 4.5 4.6 4.7 4.8 BIOS setup program................................................................... 4-10 Advanced menu.......................................................................... 4-19 Power menu.................................................................................
4.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. ASUS Update (Updates the BIOS in Windows® environment.) 3. Award BIOS Flash Utility (Updates the BIOS in DOS mode using a bootable floppy disk.) ASUS EZ Flash 2 (Updates the BIOS in DOS using a floppy disk, USB flash disk, or the motherboard support CD.) 2.
Quit all Windows® applications before you update the BIOS using this utility. Updating the BIOS through the Internet To update the BIOS through the Internet: 4- 1. Launch the ASUS Update utility from the Windows® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate. The ASUS Update main window appears. 2. Select Update BIOS from the Internet option from the drop‑down menu, then click Next. 3. Select the ASUS FTP site nearest you to avoid network traffic, or click Auto Select.
4. 5. From the FTP site, select the BIOS version that you wish to download. Click Next. Follow the screen instructions to complete the update process. The ASUS Update utility is capable of updating itself through the Internet. Always update the utility to avail all its features. Updating the BIOS through a BIOS file To update the BIOS through a BIOS file: 1. 2. 3. 4. Launch the ASUS Update utility from the Windows® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate.
4.1.2 1. Creating a bootable floppy disk Do either one of the following to create a bootable floppy disk. DOS environment a. Insert a 1.44MB floppy disk into the drive. b. At the DOS prompt, type format A:/S then press . Windows® XP environment a. Insert a 1.44 MB floppy disk to the floppy disk drive. b. Click Start from the Windows® desktop, then select My Computer. c. Select the 3 1/2 Floppy Drive icon. d. Click File from the menu, then select Format.
4.1.3 ASUS EZ Flash 2 utility The ASUS EZ Flash 2 feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS‑based utility. The EZ Flash utility is built-in the BIOS chip so it is accessible by pressing + during the Power-On Self-Test (POST). To update the BIOS using EZ Flash 2: 1. 2. 3. Visit the ASUS website (www.asus.com) to download the latest BIOS file for the motherboard.
4.1.4 Updating the BIOS The Basic Input/Output System (BIOS) can be updated using the AwardBIOS Flash Utility. Follow these instructions to update the BIOS using this utility. 1. Download the latest BIOS file from the ASUS web site. Rename the file to m2nsli.bin and save it to a floppy disk CD ROM or a USB flash disk in FAT 16/12 format. Save only the updated BIOS file in the floppy disk to avoid loading the wrong BIOS file. 2. 3. 4. Copy the AwardBIOS Flash Utility (awdflash.
7. 8. Press when the utility prompts you to save the current BIOS file. The following screen appears. The utility verifies the BIOS file in the floppy disk, CD-ROM, or USB flash disk and starts flashing the BIOS file. AwardBIOS Flash Utility for ASUS V1.14 (C) Phoenix Technologies Ltd. All Rights Reserved For NF570-SLI-M2N-SLI-DELUXE DATE:03/30/2006 Flash Type - PMC Pm49FL004T LPC/FWH File Name to Program: m2nsli.
4.1.5 Saving the current BIOS file You can use the AwardBIOS Flash Utility to save the current BIOS file. You can load the current BIOS file when the BIOS file gets corrupted during the flashing process. Make sure that the disk has enough space to save the file. To save the current BIOS file using the AwardBIOS Flash Utility: 1. 2. Follow steps 1 to 6 of the previous section. Press when the utility prompts you to save the current BIOS file. The following screen appears.
4.1.6 ASUS CrashFree BIOS 3 utility The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can update a corrupted BIOS file using the motherboard support CD, floppy, or USB flash disk that contains the updated BIOS file. Prepare the motherboard support CD, floppy, or USB flash disk containing the updated motherboard BIOS before using this utility.
4.2 BIOS setup program This motherboard supports a programmable Low-Pin Count (LPC) chip that you can update using the provided utility described in section “4.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to“Run Setup.” This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you can change the configuration of your computer in the future.
4.2.1 BIOS menu screen Menu items Main Menu bar Advanced Power Configuration fields General help Phoenix-Award BIOS CMOS Setup Utility Boot Tools Exit System Time System Date 15 : 30 : 36 Thu, Apr 6 2006 Select Menu Item Specific Help Legacy Diskette A: [1.44M, 3.5 in.
4.2.3 Legend bar At the bottom of the Setup screen is a legend bar. The keys in the legend bar allow you to navigate through the various setup menus. The following table lists the keys found in the legend bar with their corresponding functions.
4.2.7 Pop-up window Select a menu item then press to display a pop-up window with the configuration options for that item. Main Advanced Power Phoenix-Award BIOS CMOS Setup Utility Boot Tools Exit System Time System Date 15 : 30 : 36 Thu, Apr 6 2006 Legacy Diskette A: [1.44M, 3.5 in.] A: Primary IDE Master Legacy Diskette [ST321122A] Primary IDE Slave [ASUS CDS520/A] Disabled ..... [ ] SATA 1 [None] 720K , 3.5 in. ..... [ ] SATA 2 [None] 1.44M, 3.5 in. .....
4.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information. Refer to section “4.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them. Main Advanced Power Phoenix-Award BIOS CMOS Setup Utility Boot Tools Exit System Time System Date 15 : 30 : 36 Thu, Apr 6 2006 Legacy Diskette A: [1.44M, 3.5 in.
4.3.4 Primary IDE Master/Slave While entering Setup, the BIOS automatically detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press to display the IDE device information.
Access Mode [Auto] The default [Auto] allows automatic detection of an IDE hard disk drive. Select [CHS] for this item if you set the IDE Primary Master/Slave to [Manual]. Configuration options: [CHS] [LBA] [Large] [Auto] Before attempting to configure a hard disk drive, make sure you have the correct configuration information supplied by the drive manufacturer. Incorrect settings may cause the system to fail to recognize the installed hard disk. Capacity Displays the auto-detected hard disk capacity.
4.3.5 SATA 1, 2, 3, 4, 5, 6 While entering Setup, the BIOS automatically detects the presence of Serial ATA devices. There is a separate sub-menu for each SATA device. Select a device item then press to display the SATA device information.
Head Shows the number of the hard disk read/write heads. This item is not configurable. Landing Zone Shows the number of landing zone per track. This item is not configurable. Sector Shows the number of sectors per track. This item is not configurable. After entering the IDE hard disk drive information into BIOS, use a disk utility, such as FDISK, to partition and format new IDE hard disk drives. This is necessary so that you can write or read data from the hard disk.
4.4 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Take caution when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. Main Advanced Power Phoenix-Award BIOS CMOS Setup Utility Boot Tools Exit Select Menu JumperFree Configuration AI NET2 PEG Link Mode Item Specific Help Adjust system frequency/ voltage.
Standard Loads the standard settings for the system. AI Overclock Loads overclocking profiles with optimal parameters for stability when overclocking. AI N.O.S. The ASUS Non-delay Overclocking System feature intelligently determines the system load and automatically boosts the performance for the most demanding tasks. The following item becomes user-configurable when you set AI Tuning to [AI Overclocking]. Overclock Options [Disabled] Allows you to set the overclocking options.
CPU Multiplier [Auto] Allows you to set the operating CPU multiplier. The configuration options may vary depending on the type of CPU installed. Configuration options: [Auto] [5x] [6x] ~ [10x] CPU Voltage [Auto] Allows you to set the operating CPU voltage. The configuration options vary depending on the type of CPU installed. Refer to the CPU documentation before setting the CPU vCore voltage. Setting a high vCore voltage may damage the CPU.
4.4.2 AI NET2 Advanced Phoenix-Award BIOS CMOS Setup Utility AI NET2 Select Menu POST Check LAN Cable POST Check LAN2 Cable [Disabled] [Disabled] Item Specific Help Pair LAN1(1-2) LAN1(3-4) LAN1(5-6) LAN1(7-8) Status Open Open Open Open Length N/A N/A N/A N/A LAN2(1-2) LAN2(3-4) LAN2(5-6) LAN2(7-8) Open Open Open Open N/A N/A N/A N/A ↑↓ : Select Item →←: Select Menu F1:Help ESC: Exit Enable or Disable LAN cable check during POST.
4.4.4 CPU Configuration Phoenix-Award BIOS CMOS Setup Utility Advanced CPU Configuration CPU Type Select Menu AMD Engineering Sample CPU Speed 2600 MHz Cache RAM 1024K DRAM Configuration AMD Cool ‘n’ Quiet Function [Enabled] Item Specific Help DRAM timing and control. DRAM Configuration The items in the sub-menu show the DRAM-related information auto-detected by the BIOS.
DRAM ECC Enable [Disabled] Enables or disables the DRAM ECC function. This item appears only when you install DRAM modules that support ECC function. Configuration options: [Disabled] [Enabled] Advance Memory Settings CPU On-die Termination Configuration options: [Auto] [300ohm] [150ohm] [75ohm] Trc Configuration options: [Auto] [11] [12] [13]...
Dynamic Idle Cycle Counter Configuration options: [Auto] [Disabled] [Enabled] Idle Cycle Limit Configuration options: [Auto] [0 cycles] [4 cycles] [8 cycles] [16 cycles] [32 cycles] [64 cycles] [128 cycles] [256 cycles] DCQ Bypass Maximum Configuration options: [Auto] [0x] [1x] [2x] [3x]...[14x] [15x] DRAM Burst Length Configuration options: [Auto] [64-byte] [32-byte] RdPadRcvFIFO Delay Configuration options: [Auto] [1.5] [2] [2.5] [3] [3.
Address/Command Setup Time Configuration options: [Auto] [1/2 MEMCLK] [1 MEMCLK] Read DQS Timing Control Configuration options: [Auto] [No delay] [1/64 MEMCLK delay] [2/64 MEMCLK delay] [3/64 MEMCLK delay] [4/64 MEMCLK delay] [5/64 MEMCLK delay]...[46/64 MEMCLK delay] [47/64 MEMCLK delay] Write Data Timing Control Configuration options: [Auto] [No delay] [1/64 MEMCLK delay] [2/64 MEMCLK delay] [3/64 MEMCLK delay] [4/64 MEMCLK delay] [5/64 MEMCLK delay]...
4.4.5 Chipset Advanced Phoenix-Award BIOS CMOS Setup Utility Chipset CPU<->MCP55 HT Speed CPU<->MCP55 HT Width F1:Help ESC: Exit Select Menu [5x] [↓16 ↑16] ↑↓ : Select Item →←: Select Menu -/+: Change Value Enter: Select Sub-menu Item Specific Help F5: Setup Defaults F10: Save and Exit CPU<->MCP55 HT Speed [5x] Sets the processor and MCP55 HyperTransport speed.
4.4.6 PCIPnP Phoenix-Award BIOS CMOS Setup Utility Advanced PCIPnP Select Menu Plug & Play O/S [No] Item Specific Help Resources Controlled By x IRQ Resources [Auto] Select Yes if you are using a Plug and Play capable operating system. Select No if you need the BIOS to configure non-boot devices. Plug & Play O/S [No] When set to [No], the BIOS configures all the devices in the system.
4.4.
Serial-ATA Configuration This sub-menu allows you to change Serial ATA settings. Select an item then press to edit. Phoenix-Award BIOS CMOS Setup Utility Advanced Serial-ATA Configuration x x x x x x Serial-ATA Controller RAID Enabled SATA 1 RAID SATA 2 RAID SATA 3 RAID SATA 4 RAID SATA 5 RAID SATA 6 RAID [Enabled] [Disabled] Disabled Disabled Disabled Disabled Disabled Disabled Select Menu Item Specific Help Serial-ATA Controller [Enabled] Enables or disables the Serial ATA controller.
Onboard 1394 Controller [Enabled] Allows you to disable or enable the onboard 1394 device support. Configuration options: [Disabled] [Enabled] Onboard 1st/2nd Nvidia LAN [Enabled] Enables or disables the onboard NVIDIA® LAN controller. Configuration options: [Disabled] [Enabled] OnBoard LAN Boot ROM [Disabled] Allows you to enable or disable the onboard LAN boot ROM.
4.5 Power menu The Power menu items allow you to change the settings for the Advanced Configuration and Power Interface (ACPI) and the Advanced Power Management (APM). Select an item then press to display the configuration options. Main Advanced Power Phoenix-Award BIOS CMOS Setup Utility Boot Tools Exit ACPI Suspend Type ACPI APIC support APM Configuration Hardware Monitor F1:Help ESC: Exit 4.5.
4.5.
Power On By RTC Alarm [Disabled] Allows you to enable or disable RTC to generate a wake event. When this item is set to Enabled, the items Date of Month Alarm and Time (hh:mm:ss) Alarm items become user-configurable with set values. Configuration options: [Disabled] [Enabled] Date of Month Alarm [Disabled] To set the date of alarm, highlight this item and press to display the Date of Month Alarm pop-up menu. Key-in a value within the specified range then press .
2.5.4 Hardware Monitor The items in this sub-menu displays the hardware monitor values automatically detected by the BIOS. It also allows you to change CPU Q-Fan feature-related parameters. Select an item then press to display the configuration options. Power Phoenix-Award BIOS CMOS Setup Utility Hardware Monitor x x Select Menu CPU Q-Fan Control CPU Q-Fan Profile Chassis Q-Fan Control Chassis Q-Fan Profile Vcore Voltage 3.
The Chassis Q-Fan Profile item becomes user-configurable when you set the Chassis Q-Fan Control item to [Enabled]. Chassis Q-Fan Profile [Performance] Allows you to set the appropriate performance level of the chassis Q-Fan. When set to [Optimal], the chassis fan automatically adjusts depending on the chassis temperature. Set this item to [Silent] to minimize fan speed for quiet chassis fan operation, or [Performance] to achieve maximum chassis fan speed.
4.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press to display the sub-menu. Main Advanced Power Phoenix-Award BIOS CMOS Setup Utility Boot Tools Exit Select Menu Boot Device Priority Removable Drives Hard Disk Drives CDROM Drives Boot Settings Configuration Security ↑↓ : Select Item →←: Select Menu F1:Help ESC: Exit 4.6.
4.6.2 Removable Drives Phoenix-Award BIOS CMOS Setup Utility Boot Removable Drives 1. Floppy Disks Select Menu Item Specific Help 1. Floppy Disks Allows you to assign a removable drive attached to the system. 4.6.3 Hard Disk Drives Phoenix-Award BIOS CMOS Setup Utility Boot Hard Disk Drives 1. 1st Master: XXXXXXXXX Select Menu Item Specific Help 1. 1st Master: XXXXXXXXX Allows you to assign hard disk drives attached to the system. 4.6.
4.6.
Typematic Rate (Chars/Sec) [6] Allows you to select the rate at which a character repeats when you hold a key. Configuration options: [6] [8] [10] [12] [15] [20] [24] [30] Typematic Delay (Msec) [250] Allows you to set the delay before keystrokes begin to repeat. Configuration options: [250] [500] [750] [1000] OS Select for DRAM > 64MB [Non-OS2] Set this item to OS2 only when you are running on an OS/2 operating system with an installed RAM of greater than 64 KB.
3. When prompted, confirm the password by typing the exact characters again, then press . The password field setting is changed to Set. To clear the password: 1. Select the password field and press twice. The following message appears: PASSWORD DISABLED !!! Press any key to continue... 2. Press any key to continue. The password field setting is changed to Clear. A note about passwords The Supervisor password is required to enter the BIOS Setup program preventing unauthorized access.
4.7 Tools menu The Tools menu items allow you to configure options for special functions. Select an item then press to display the sub-menu. Main Advanced Power Phoenix-Award BIOS CMOS Setup Utility Boot Tools Exit ASUS Music Alarm ASUS O.C. Profile ASUS EZ Flash 2 F1:Help ESC: Exit 4.7.
Alarm Date: Sunday/Monday/Tuesday/Wednesday/Thursday/Friday/ Saturday [Enabled] Allows you to enable or disable the alarm for a particular day. Configuration options: [Disabled] [Enabled] Alarm Time (hh:mm) 0 : 0 Allows you to set the alarm time. Press to select the field, then use <+> or <-> to change the value.
4.7.2 ASUS O.C. Profile This item allows you to store or load multiple BIOS settings. Phoenix-Award BIOS CMOS Setup Utility Tools ASUS BIOS Profile Load BIOS Profile Save BIOS Profile Select Menu Item Specific Help Press [Enter] to select. Load BIOS Profile Phoenix-Award BIOS CMOS Setup Utility Tools Load BIOS Profile Load from Profile 1 Load from Profile 2 Load from File Select Menu Item Specific Help Load BIOS Profile from Profile 1.
Save BIOS Profile Phoenix-Award BIOS CMOS Setup Utility Tools Save BIOS Profile Select Menu Save to Profile 1 Save to Profile 2 Save to File Item Specific Help Save current BIOS Profile to Profile 1. Save to Profile 1/2 Allows you to save the current BIOS file to the BIOS Flash. Press to save the file. Save to File Allows you to save the current BIOS file to the hard disk, a floppy, or USB flash disk with a FAT32/16/12 format. To save the BIOS file: 1.
4.7.4 ASUS EZ Flash 2 Allows you to run ASUS EZ Flash 2. Press to start EZ Flash 2 then from the confirmation screen, use the left or right arrows to select [Yes] or [No] then press . The following screen appears if you select [Yes]. Follow screen instructions to flash the BIOS. ASUSTek EZ Flash 2 BIOS ROM Utility B311 FLASH TYPE: Winbond W39V080A 8Mb LPC Current ROM Update ROM BOARD: M2NSLI Deluxe BOARD: Unknown VER: 0122.
4.8 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items. Main Advanced Power Phoenix-Award BIOS CMOS Setup Utility Boot Tools Exit Exit & Save Changes Exit & Discard Changes Load Setup Default Discard Changes F1:Help ESC: Exit ↑↓ : Select Item →←: Select Menu Select Menu Item Specific Help This option save data to CMOS and exiting the setup menu.
4-48 Chapter 4: BIOS setup
This chapter describes the contents of the support CD that comes with the motherboard package.
Chapter summary 5.1 5 Installing an operating system.................................................... 5-1 5.2 Support CD information............................................................... 5-1 5.4 RAID configurations................................................................... 5-28 5.3 5.5 Software information.................................................................... 5-8 Creating a RAID driver disk........................................................
5.1 Installing an operating system This motherboard supports Windows® 2000/XP/64-bit XP operating systems (OS). Always install the latest OS version and corresponding updates to maximize the features of your hardware. 5.2 • Motherboard settings and hardware options vary. Use the setup procedures presented in this chapter for reference only. Refer to your OS documentation for detailed information.
5.2.2 Drivers menu The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. Nvidia Chipset Driver Program Installs the NVIDIA® Chipset drivers for the NVIDIA® nForce™ 570 SLI chipset. AMD Cool ‘n’ Quiet Driver Installs the AMD Cool ‘n’ Quiet™ technology driver. SoundMAX ADI1988 Audio Driver Installs the SoundMAX® ADI1988 audio driver and application.
5.2.3 Utilities menu The Utilities menu shows the applications and other software that the motherboard supports. ASUS Cool ‘n’ Quiet Utility Installs the AMD Cool ‘n’ Quiet™ software. ASUS PC Probe II This smart utility monitors the fan speed, CPU temperature, and system voltages, and alerts you of any detected problems. This utility helps you keep your computer in healthy operating condition. ASUS Update The ASUS Update utility allows you to update the motherboard BIOS in Windows® environment.
ASUS AI Booster The ASUS AI Booster application allows you to overclock the CPU speed in Windows® environment. ASUS AI Nap The ASUS AI Nap application allows you to minimize the power consumption of your computer whenever you are away. ASUS AI Gear The ASUS AI Gear application provides system performance options that allows you to select the best performance for your computing needs. Anti-virus Utility The anti-virus application scans, identifies, and removes computer viruses.
Make nVidia 32bit SATA RAID Driver Make nVidia 64bit SATA RAID Driver Allows you to create an NVIDIA® Serial ATA RAID driver disk for a 32-bit/64-bit system. Make JMicron JMB363 RAID Driver Disk Allows you to create a JMicron® JMB363 RAID driver disk. 5.2.5 Manuals menu The Manuals menu contains a list of supplementary user manuals. Click an item to open the folder of the user manual. Most user manual files are in Portable Document Format (PDF).
5.2.6 ASUS Contact information Click the Contact tab to display the ASUS contact information. You can also find this information on the inside front cover of this user guide. 5.2.7 Other information The icons on the top right corner of the screen give additional information on the motherboard and the contents of the support CD. Click an icon to display the specified information. Motherboard Info Displays the general specifications of the motherboard.
Browse this CD Displays the support CD contents in graphical format. Technical support Form Displays the ASUS Technical Support Request Form that you have to fill out when requesting technical support.
5.3 Software information 5.3.1 Cool ‘n’ Quiet!™ Technology Most of the applications in the support CD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software application for more information. The motherboard supports the AMD Cool ‘n’ Quiet!™ Technology that dynamically and automatically change the CPU speed, voltage, and amount of power depending on the task the CPU performs.
Windows® 98 SE/Me 1. 2. 3. 4. 5. 6. From the Windows® 98 SE/Me operating system, click the Start button. Select Settings, then Control Panel. Double-click the Display icon in the Control Panel then select the Screen Saver tab. From the Energy saving features of monitor group, click the Settings... button. From the Power Options Properties dialog box, select the AMD’s Cool ‘n’ Quiet(tm) Technology tab. Click the Performance combo list box to select desired mode.
Launching the Cool ‘n’ Quiet!™ software The motherboard support CD includes the Cool ‘n’ Quiet!™ software that enables you to view your system’s real-time CPU Frequency and voltage. Make sure to install the Cool ‘n’ Quiet!™ software from the motherboard support CD. Refer to section “5.2.3 Utilities menu” for details. To launch the Cool ‘n’ Quiet!™ program: 1. 2. 3. 5-10 If you are using Windows® 98SE/Me/2000, click the Start button. Select Programs-> ASUS -> Cool & Quiet -> Cool & Quiet.
5.3.2 ASUS PC Probe II PC Probe II is a utility that monitors the computer’s vital components, and detects and alerts you of any problem with these components. PC Probe II senses fan rotations, CPU temperature, and system voltages, among others. Because PC Probe II is software-based, you can start monitoring your computer the moment you turn it on. With this utility, you are assured that your computer is always at a healthy operating condition.
Button Function Opens the Configuration window Opens the Report window Opens the Desktop Management Interface window Opens the Peripheral Component Interconnect window Opens the Windows Management Instrumentation window Opens the hard disk drive, memory, CPU usage window Shows/Hides the Preference section Minimizes the application Closes the application Sensor alert When a system sensor detects a problem, the main window right handle turns red, as the illustrations below show.
Hardware monitor panels The hardware monitor panels display the current value of a system sensor such as fan rotation, CPU temperature, and voltages. The hardware monitor panels come in two display modes: hexagonal (large) and rectangular (small). When you check the Enable Monitoring Panel option from the Preference section, the monitor panels appear on your computer’s desktop.
Monitoring sensor alert The monitor panel turns red when a component value exceeds or is lower than the threshold value. Refer to the illustrations below. Small display Large display WMI browser Click to display the WMI (Windows Management I n s t r u m e n t a t i o n ) b r o w s e r. T h i s browser displays various Windows ® management information. Click an item from the left panel to display on the right panel. Click the plus sign (+) before WMI Information to display the available information.
PCI browser Click to display the PCI (Peripheral Component Interconnect) b r o w s e r. T h i s b r o w s e r p r o v i d e s information on the PCI devices installed on your system. Click the plus sign (+) before the PCI Information item to display available information. Usage The Usage browser displays real-time information on the CPU, hard disk drive space, and memory usage. Click to display the Usage browser. CPU usage The CPU tab displays real-time CPU usage in line graph representation.
Memory usage The Memory tab shows both used and available physical memory. The pie chart at the bottom of the window represents the used (blue) and the available physical memory. Configuring PC Probe II Click to view and adjust the sensor threshold values. The Config window has two tabs: Sensor/Threshold and Preference. The Sensor/ Threshold tab enables you to activate the sensors or to adjust the sensor threshold values.
5.3.3 ASUS Music Alarm This motherboard is equipped with an audio alarm clock called ASUS Music Alarm. The ASUS Music Alarm gives you a personal wake-up called with your favorite CD music when the system is off. The onboard audio CODEC supports this feature, which requires an optical drive (CD-ROM, CD-RW, or DVD-ROM). • Make sure that the power cord is plugged to a grounded power source so that the system has standby power. • ASUS Music Alarm only supports audio CDs.
OS configuration To configure ASUS Music Alarm in Windows® 1. Place the support CD into the optical drive. 3. Insert an audio CD into the optical drive. 2. 4. Click the Utilities tab and choose ASUS Music Alarm to install the utility. Launch the ASUS Music Alarm application by going to Start > ASUS > ASUS Music Alarm. The main window appears.
7. Click the arrow ( ) next to Options in the Options section. The Options panel appears. Disable or select the Repeat mode, then specify the length of the alarm music to play. Set the desired volume. When done, click OK. 8. After you have finished making all the required settings, turn off the system. Adjusting the volume To adjust the volume while the music alarm is playing: • Use the or arrow key to increase or decrease the volume.
5.3.4 ASUS AI Nap This feature allows you to minimize the power consumption of your computer whenever you are away. Enable this feature for minimum power consumption and a more quiet system operation. After installing AI Nap from the bundled support CD, you can launch the utility by double-clicking the AI Nap icon on the Windows OS taskbar. Click Yes on the confirmation screen. To exit AI Nap mode, press the system power or mouse button then click Yes on the confirmation screen.
5.3.5 ASUS AI Gear ASUS AI Gear provides four system performance options that allows you to select the best performance setting for your computing needs. This easy-to-use utility adjusts the processor frequency and vCore voltage to minimize system noise and power consumption. After installing AI Gear from the bundled support CD, you can launch AI Gear by double-clicking the AI Gear icon on your Windows OS taskbar. Shift the gear to the performance setting that you like.
You can also set the AI Gear modes by clicking the AI Gear icon on the Windows taskbar. 5-22 • When AI Gear is enabled, the system will automatically optimize the CPU and chassis fan speed according to the system loading. • The AI Booster (AI NOS) and AI Gear functions cannot be enabled simultaneously.
5.3.6 SoundMAX® High Definition Audio utility The ADI AD1988B High Definition Audio CODEC provides 8-channel audio capability through the SoundMAX ® audio utility with AudioESP™ software to deliver the ultimate audio experience on your PC. The software implements high quality audio synthesis/rendering, 3D sound positioning, and advanced voice-input technologies.
From the taskbar, double-click on the SoundMAX® icon to display the SoundMAX® Control Panel. Audio Setup Wizard By clicking the icon from the SoundMAX® control panel, you can easily configure your audio settings. Simply follow succeeding screen instructions and begin enjoying High Definition Audio.
Jack configuration This screen helps you configure your computer’s audio ports, depending on the audio devices you have installed. Adjust speaker volume This screen helps you adjust speaker volume. Click the Test button to hear the changes you have made. Adjust microphone volume This screen helps you adjust microphone volume. You will be asked to read pre-written text to allow the AudioWizard to adjust the volume as you speak.
Audio preferences Click the icon to go to the Preferences page. This page allows you to change various audio settings. General options Click the General tab to choose your playback and recording devices, enable/ disable the AudioESP™ feature, and enable/disable digital output. Microphone options Click the Listening Environment tab allows you to optimize your microphone input settings.
Enhanced Microphone Features Voice recording Enables Noise Filter function. Detects repetitive and stationary noises like computer fans, air conditioners, and other background noises then eliminates it in the incoming sudio stream while recording. You can enable it for a better recording quality. Directional Array Receives only the sound coming from the reception cone and eliminates interferences including neighboring speakers and reverberations.
5.4 RAID configurations The motherboard comes with the NVIDIA® nForce™ 570 SLI MultiShield™ and JMicro® JMB363 RAID controllers that allow you to configure Serial ATA hard disk drives as RAID sets. The motherboard supports the following RAID configurations. RAID 0 (Data striping ) optimizes two identical hard disk drives to read and write data in parallel, interleaved stacks.
If you want to boot the system from a hard disk drive included in a RAID set, copy first the RAID driver from the support CD to a floppy disk before you install an operating system to a selected hard disk drive. Refer to section “5.6 Creating a RAID driver disk” for details. 5.4.1 Installing hard disks The motherboard supports Serial ATA hard disk drives. For optimal performance, install identical drives of the same model and capacity when creating a disk array.
5.4.2 NVIDIA® MediaShield™ RAID configurations The motherboard includes a high performance SATA RAID controller integrated in the NVIDIA® nForce™ 570 SLI southbridge chipset. It supports RAID 0, RAID 1, RAID 0+1, RAID 5 and JBOD for six independent Serial ATA channels. Setting the BIOS RAID items After installing the hard disk drives, make sure to set the necessary RAID items in the BIOS before setting your RAID configuration. To set the BIOS RAID items: 1. 2. 3. 4.
Entering the NVIDIA® MediaShield RAID utility To enter the NVIDIA® RAID utility: 1. 2. Boot up your computer. During POST, press to display the main menu of the utility. The RAID BIOS setup screens shown in this section are for reference only, and may not exactly match the items on your screen. NVIDIA RAID Utility Oct 5 2004 - Define a New Array RAID Mode: Striping Striping Block: Free Disks Loc Disk Model Name Array Disks Loc Disk Model Name 1.0.M 1.1.M 2.0.M 2.1.
2. Press select the Striping Block then press . The following submenu appears: 8K ↑ 16K 32K 64K 128K Optim↓ If you selected Striping or Stripe Mirroring, use the up or down arrow keys to select the stripe size for your RAID 0 array then press .The available values range from 8 KB to 128 KB. The default selection is 128 KB. The strip value should be chosen based on the planned drive usage.
NVIDIA RAID Utility Oct 5 2004 - Array List Boot Id Status Vendor Array Model Name No 4 Healthy NVIDIA MIRROR [Ctrl-X]Exit 6. [↑↓]Select [B]Set Boot XXX.XXG [N]New Array [ENTER]Detail A new set of navigation keys is displayed on the bottom of the screen. Press to save settings and exit. Rebuilding a RAID array To rebuild a RAID array: 1. From the Array List menu, use the up or down arrow keys to select a RAID array then press . The RAID Array details appear.
2. A new set of navigation keys is displayed on the bottom of the screen. Press to rebuild a RAID array. The following screen appears. Array 1 : NVIDIA MIRROR XXX.XXG - Select Disk Inside Array RAID Mode: Mirroring Striping Width: 1 Striping Block: 64K Adapt Channel M/S Index Disk Model Name Capacity 2 1 1 0 Master Master 0 1 XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX XXX.XXGB XXX.XXGB [↑↓] Select [F6] Back 3.
Deleting a RAID array To delete a RAID array: 1. From the Array List menu, use the up or down arrow keys to select a RAID array then press . The RAID Array details appear. Array 1 : NVIDIA MIRROR XXX.XXG - Array Detail RAID Mode: Mirroring Striping Width: 1 Adapt Channel M/S Index Disk Model Name Capacity 2 1 1 0 Master Master 0 1 XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX XXX.XXGB XXX.XXGB [R] Rebuild 2.
Clearing a disk data To clear disk data: 1. From the Array List menu, use the up or down arrow keys to select a RAID array then press . The RAID Array details appear. Array 1 : NVIDIA MIRROR XXX.XXG - Array Detail RAID Mode: Mirroring Striping Width: 1 Adapt Channel M/S Index Disk Model Name Capacity 2 1 1 0 Master Master 0 1 XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX XXX.XXGB XXX.XXGB [R] Rebuild 2.
5.4.3 JMicron® RAID Configuration The JMicron® Serial ATA controller allows you to configure RAID 0 and RAID 1 sets on the external Serial ATA hard disk drives. Before creating a RAID set Prepare the following items: • At two HDDs, preferably with the same model and capacity. • Microsoft® Windows® OS installation disk (Windows 2000/XP/2003) • A white floppy disk • Motherboard support CD with JMB363 driver Complete the following steps before you create a RAID set: 1. 2.
Entering the JMB363 RAID BIOS utility 1. During POST, press to enter the JBM363 RAID BIOS menu. 2. The main JMB363 RAID BIOS menu appears. 3. Use the arrow keys to move the color bar and navigate through the items. Creating a RAID set 1. 5-40 In the main JMB363 RAID BIOS menu, highlight Create RAID Disk Drive using the up/down arrow key then press .
2. When the Level item is highlighted, use the up/down arrow key to select the RAID set that you want to create. 3. When the Disks item is highlighted, use the up/down arrow key to highlight an HDD that you want to belong to the RAID set, then press the space bar to confirm selection. Repeat the process until the HDDs are selected. A selected HDD shows a 4. sign before it. Key in the RAID volume capacity. Use the up/down arrow to choose the block size.
5. When done, press to confirm the creation of the RAID set. A dialogue box appears to confirm the action. Press to confirm; otherwise, press . Pressing deletes all the data in the HDDs. 6. 5-42 The following screen appears, displaying the relevant information about the RAID set you created.
Deleting a RAID set 1. In the main JMB363 RAID BIOS menu, highlight Delete RAID Disk Drive using the up/down arrow key then press . 2. Use the space bar to select the RAID set you want to delete. 3. A selected set shows a set. sign before it. Press the key to delete the A dialogue box appears to confirm the action. Press to confirm; otherwise, press . Pressing deletes all the data in the HDDs.
Resetting disks to non-RAID When you install an HDD that has been configured as part of another RAID set, you may convert this broken RAID HDD to non-RAID mode. All original data, however, will be lost. To prevent damage to your system, you cannot select the HDD when configuring a RAID set through the JMB363 utility. To reset disks to non-RAID: 1. In the main JMB363 RAID BIOS menu, highlight Revert HDD to non‑RAID using the up/down arrow key then press . 2.
5.5 Creating a RAID driver disk A floppy disk with the RAID driver is required when installing Windows® 2000/XP operating system on a hard disk drive that is included in a RAID set. To create a RAID driver disk: 1. Place the motherboard support CD into the CD-ROM drive. 3. From the Make Disk menu, select the RAID driver disk you want to create or browse the contents of the support CD to locate the driver disk utility. 2. Select Make Disk tab. Refer to section “5.2.4 Make Disk menu” for details. 4.
5-46 Chapter 5: Software support
This chapter tells how to install SLI‑ready PCI Express graphics cards.
Chapter summary 6.1 Overview................................................................................ 6-1 6.2 Dual graphics cards setup......................................................
6.1 Overview The motherboard supports the NVIDIA® SLI™ (Scalable Link Interface) ‑ Intel® Edition technology that allows you to install two identical PCI Express™ x16 graphics cards. Follow the installation procedures in this section. Requirements • Two identical SLI-ready graphics cards that are NVIDIA® certified. • Make sure that your graphics card driver supports the NVIDIA SLI technology. Download the latest driver from the NVIDIA website (www.nvidia.com).
6.2 Dual graphics card setup 6.2.1 Installing SLI-ready graphics cards Install only identical SLI-ready graphics cards that are NVIDIA®-certified. Different types of graphics cards will not work together properly. To install the graphics cards: 1. Prepare two graphics cards. Each graphics card should have goldfingers for the SLI connector. Goldfingers 2. 6- Remove the metal bracket covers opposite the two PCI Express x16 slots.
3. Insert one graphics card into either the blue or black slot. Make sure that the card is properly seated on the slot. 4. Insert the second graphics card into the other slot. Make sure that the card is properly seated on the slot. If required, connect an auxiliary power source to the PCI Express graphics cards.
5. Align and insert the SLI connector to the goldfingers on each graphics card. Make sure that the connector is firmly in place. SLI connector 6. When installing two VGA cards using a 20-pin ATX PSU with sufficient+12v capability, we recommend that you connect the auxillary power source from the power supply to the graphics card. Refer to the PSU documentation for dual VGA power requirements. 7. Connect a VGA cable or a DVI-I cable to the graphics card/s.
6.2.2 Installing the device drivers Refer to the documentation that came with your graphics card package to install the device drivers. Make sure that your PCI Express graphics card driver supports the NVIDIA SLI technology. Download the latest driver from the NVIDIA website (www.nvidia.com). 6.2.3 Enabling the multi-GPU feature in Windows® After installing your graphics cards and the device drivers, enable the Multi‑Graphics Processing Unit (GPU) feature in the NVIDIA nView properties.
5. From the Display Properties dialog box, select the Settings tab then click Advanced. 6. Select the NVIDIA GeForce tab. 7. Click the slider to display the following screen, then select the SLI multi‑GPU item. Slider 8. 9. 6- Click the Enable SLI multi-GPU check box. Click OK when done.
