User Guide Motherboard M2V
E2736 Checklist Revised Edition V2 July 2006 Copyright © 2006 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Features Notices............................................................................................ vii Safety information...........................................................................viii About this guide............................................................................... ix How this guide is organized.................................................... ix Where to find more information..............................................
Contents Safeguards 2.6 2.7 2.5.6 PCI Express x16 slot..............................................2-16 Jumpers..............................................................................2-17 Connectors.........................................................................2-19 2.7.1 Rear panel connectors...........................................2-19 2.7.2 Internal connectors.................................................2-21 Chapter 3: Powering up 3.1 3.2 Starting up for the first time..........
Contents 4.5 4.6 4.7 4.8 4.4.1 JumperFree Configuration.....................................4-15 4.4.2 USB Configuration.................................................4-15 4.4.3 CPU Configuration.................................................4-17 4.4.3 CPU Configuration.................................................4-17 4.4.4 Chipset...................................................................4-21 4.4.5 Onboard Devices Configuration.............................4-22 4.4.6 PCI PnP.............
Contents 5.6 vi Cool ‘n’ Quiet!™ Technology...............................................5-20 5.6.1 Enabling Cool ‘n’ Quiet!™ Technology...................5-20 5.6.2 Launching the Cool ‘n’ Quiet!™ software...............
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing the motherboard. How this guide is organized This manual contains the following parts: • Chapter 1: Product introduction This chapter describes the motherboard features and the new technologies it supports. • Chapter 2: Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Information that you MUST follow to complete a task. NOTE: Tips and additional information to aid in completing a task.
M2V specifications summary CPU Socket AM2 for AMD Athlon™ 64 X2/Athlon™ 64FX/ Athlon™ 64/Sempron™ processor Supports AMD 64 architecture that enables simultaneous 32-bit and 64-bit computing Supports AMD Cool ‘n’ Quiet!™ Technology Chipset VIA K8T890 VIA VT8237A System Bus 2000 MT/s Memory Dual-channel memory architecture 4 x 240-pin DDR2 DIMM sockets support ECC/non-ECC unbuffered 533/667/800 MHz DDR memory modules Expansion slots 1 x PCIEX16 1 x PCIEX1 4 x PCI Storag
M2V specifications summary Internal I/O 2 x USB 2.0 connectors for 4 additional USB ports 1 x CPU fan connector 2 x Chassis fan connectors 24-pin/4-pin ATX 12V power connectors CD connector Front panel audio connector System panel connector Chassis Intrusion 3 x SATA connectors 2 x IDE connectors 1 x Floppy disk drive connector 1 x COM connector 1 x S/PDIF Out connector BIOS features 4Mb Flash ROM AMI BIOS with enhanced ACPI, PnP, DMI2.0, Green Industry standard PCI 2.2, USB 2.0/1.
Chapter 1 This chapter describes the motherboard features and the new technologies it supports.
Chapter summary 1.1 Welcome!..........................................................1-1 1.2 Package contents.............................................1-1 1.3 Special features................................................
1.1 Welcome! Thank you for buying the ASUS® M2V motherboard! The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your motherboard package for the following items.
1.3 Special features 1.3.1 Product highlights Latest processor technology The motherboard comes with a 940-pin AM2 socket that supports AMD Athlon™ 64 X2/Athlon™ 64/Athlon™ FX/Sempron™ processor. With an integrated low-latency high-bandwidth memory controller and a highly scalable HyperTransport™ technology-based system bus, the motherboard provides a powerful platform for your diverse computing needs, increased office productivity, and enhanced digital media experience. See page 2-6.
Serial ATA support The motherboard provides a high-performance Serial ATA RAID controller that enhances hard disk performance and data backup protection without the cost of additional RAID cards. The onboard VIA VT8237A RAID controller provides RAID 0, RAID 1, and JBOD configuration to two Serial ATA connectors. The onboard Marvell 88SE6121 controller supports two additional SATA 3.0 Gb/s connectors. See pages 2-23 and 5-10.
1.3.2 Unique ASUS features ASUS O.C. Profile The motherboard features the ASUS O.C. Profile that allows users to conveniently store or load multiple BIOS settings. The BIOS settings can be stored in the CMOS or a separate file, giving users the freedom to share and distribute their favorite overclocking settings. See page 4-34. 6-channel audio The motherboard comes with the Realtek ALC660 audio CODEC that provides 6-channel audio, audio jack-sensing and enumeration technology, and S/PDIF out support.
ASUS MyLogo2™ This new feature present in the motherboard allows you to personalize and add style to your system with customizable boot logos. See pages 4-30, 5‑7. C.P.R. (CPU Parameter Recall) The C.P.R. feature of the motherboard BIOS allows automatic re-setting to the BIOS default settings in case the system hangs due to overclocking. When the system hangs due to overclocking, C.P.R. eliminates the need to open the system chassis and clear the RTC data.
1- Chapter 1: Product introduction
Chapter 2 This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
Chapter summary 2.1 Before you proceed..........................................2-1 2.2 Motherboard overview.....................................2-2 2.3 Central Processing Unit (CPU)........................2-6 2.4 System memory.............................................. 2-11 2.5 Expansion slots..............................................2-14 2.6 Jumpers..........................................................2-17 2.7 Connectors.....................................................
2.1 Before you proceed Note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Use a grounded wrist strap or touch a safely grounded object or to a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity. • Hold components by the edges to avoid touching the ICs on them.
2.2 Motherboard overview Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components. 2.2.1 Placement direction When installing the motherboard, make sure that you place it into the chassis in the correct orientation.
2.2.3 Motherboard layout 20.5cm (8.0in) 30.5cm (12.
2.2.4 Layout Contents 2- Slots Page 1. DDR2 DIMM slots 2-11 2. PCI slots 2-16 3. PCI Express x 1 slot 2-16 4. PCI Express x 16 slot 2-16 Jumpers Page 1. Clear RTC RAM (3-pin CLRTC) 2-17 2. Keyboard power (3-pin KBPWR) 2-18 3. USB device wake-up (3-pin USBPWR1, USBPWR2) 2-18 Rear Panel Connectors Page 1. PS/2 mouse port 2-19 2. Parallel port 2-19 3. Gigabit LAN port (RJ-45) 2-19 4. Line In port 2-19 5.
Internal Connectors Page 1. Primary IDE connector (40-1 pin PRI_IDE) 2-21 2. Secondary IDE connector (40-1 pin SEC_IDE) 2-21 3. Floppy disk connector (34-1 pin FLOPPY) 2-22 4. Serial ATA connectors (7-pin SATA1, SATA2) 2-22 5. Marvell® 88SE6121 Serial ATA RAID connector (7-pin SATA_RAID1) 2-23 6. CPU fan connector (4-pin CPU_FAN) 2-24 7. Chassis fan connector (3-pin CHA_FAN) 2-24 8. CD connector (4-pin CD) 2-24 9.
2.3 Central Processing Unit (CPU) The motherboard comes with a 940-pin AM2 socket designed for the AMD Athlon™ 64 X2/Athlon™ 64/Athlon™ FX/Sempron™ processor. The AM2 socket has a different pinout from the 940-pin socket designed for the AMD Opteron™ processor. Make sure you use a CPU is designed for the AM2 socket. The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU! 2.3.
3. Position the CPU above the socket such that the CPU corner with the gold triangle matches the socket corner with a small triangle. 4. Carefully insert the CPU into the socket until it fits in place. Gold triangle Small triangle 5. When the CPU is in place, push down the socket lever to secure the CPU. The lever clicks on the side tab to indicate that it is locked. 6. Install a CPU heatsink and fan following the instructions that came with the heatsink package.
2.3.2 Installing the heatsink and fan The AMD Athlon™ 64FX or AMD Athlon 64™ processor require a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. Make sure that you use only qualified heatsink and fan assembly. Follow these steps to install the CPU heatsink and fan. 1. Place the heatsink on top of the installed CPU, making sure that the heatsink fits properly on the retention module base.
2. Attach one end of the retention bracket to the retention module base. 3. Align the other end of the retention bracket (near the retention bracket lock) to the retention module base. A clicking sound denotes that the retention bracket is in place. Make sure that the fan and heatsink assembly perfectly fits the retention mechanism module base, otherwise you cannot snap the retention bracket in place. 4.
2.3.3 Connecting the CPU fan cable When the heatsink and fan assembly is in place, connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN. CPU_FAN GND CPU FAN PWR CPU FAN IN CPU FAN PWM M2V M2V CPU Fan Connector • • 2-10 Do not forget to connect the CPU fan connector! CPU overheating and hardware monitoring errors may occur if you fail to plug this connector. This connector is also compatible with the old 3-pin CPU fan.
2.4 System memory 2.4.1 Overview The motherboard comes with four Double Data Rate 2 (DDR2) Dual Inline Memory Modules (DIMM) sockets. A DDR2 module has the same physical dimensions as a DDR DIMM but has a 240-pin footprint compared to the 184-pin DDR DIMM. DDR2 DIMMs are notched differently to prevent installation on a DDR DIMM socket.
2.4.2 Memory configurations You may install 256 MB, 512 MB, 1 GB and 2GB unbuffered ECC/non-ECC DDR2 DIMMs into the DIMM sockets. • Always install DIMMs with the same CAS latency. For optimum compatibility, we recommend that you obtain memory modules from the same vendor. Visit the ASUS website (www.asus.com) for the latest Qualified Vendors List. • When using only one DDR DIMM module, install it into slot DIMM_A1 or DIMM_B1.
DDR2 Qualified Vendors List The following tables list the DDR2 800/667/533 memory modules that have been tested and qualified for use with this motherboard.
Table 4 DDR2 533 Qualified Vendors List Size Vendor Model Brand SS/DS 1024MB 256MB 512MB 512MB 256MB 512MB 1024MB HYNIX INFINEON INFINEON MICRON SAMSUNG SAMSUNG SAMSUNG HYMP512U728-C4 AA HYS64T32000HU-3.7-B HYS64T64000GU-3.
2.4.3 Installing a DIMM Unplug the power supply before adding or removing DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components. 2 To install a DIMM: 1. Unlock a DIMM socket by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. 3.
2.5 Expansion slots In the future, you may need to install expansion cards. The motherboard has available PCI slots, PCI Express x1 slot and PCI Express x16 slot. The following sub-sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. 2.5.1 Installing an expansion card Follow these steps to install an expansion card. 1.
2.5.
2.5.4 PCI slots The PCI slots support PCI cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The following figure shows a LAN card installed on a PCI slot. 2.5.5 PCI Express x1 slot This motherboard supports PCI Express x1 network cards, SCSI cards and other cards that comply with the PCI Express specifications. The figure blow shows a network card installed on the PCI Express x1 slot. 2.5.
2.6 Jumpers 1. Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The RAM data in CMOS, that include system setup information such as system passwords, is powered by the onboard button cell battery. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the onboard battery. 3. Move the jumper from pins 1-2 (default) to pins 2-3.
2. Keyboard power (3-pin KBPWR) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) if you wish to wake up the computer when you press a key on the keyboard. This feature requires an ATX power supply that can supply at least 1A on the +5VSB lead, and a corresponding setting in the BIOS . KBPWR 3 2 2 1 +5V (Default) +5VSB M2V M2V Keyboard Power Setting 3.
2.7 Connectors 2.7.1 Rear panel connectors 1 3 2 4 5 6 11 9 10 8 7 1. PS/2 mouse port. This green 6-pin connector is for a PS/2 mouse. 2. Parallel port. This 25-pin port connects a parallel printer, a scanner, or other devices. 3. RJ-45 port. This port allows connection to a Local Area Network (LAN) through a network hub. The left LED is blinking in half duplex mode. 4. Line-In port. This Line In (light blue) port connects a tape player or other audio sources. 5. Line-Out port.
7. USB 2.0 ports 3 and 4. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. 8. USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. 9. External Serial ATA 3Gb/s port. This port connects to an external SATA box or a Serial ATA port multiplier. The external SATA port supports external Serial ATA 1.5Gb/s and 3Gb/s devices.
2.7.2 Internal connectors 1. IDE connector (40-1 pin PRI_IDE) The onboard IDE connector is for the Ultra DMA 133/100/66 signal cable. There are three connectors on each Ultra DMA 133/100/66 signal cable: blue, black, and gray. Connect the blue connector to the motherboard’s IDE connector, then select one of the following modes to configure your device.
2. Floppy disk drive connector (34-1 pin FLOPPY) This connector supports the provided floppy drive ribbon cable. After connecting one end to the motherboard, connect the other end to the floppy drive. (Pin 5 is removed to prevent incorrect insertion when using ribbon cables with pin 5 plug). M2V FLOPPY PIN 1 NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. M2V Floppy Disk Drive Connector 3.
Important notes on Serial ATA solution: • The Serial ATA cable is smaller and more flexible, allowing easier routing inside the chassis. The lower pin count of the Serial ATA cable eliminates the problem caused by the wide, flat ribbon cables of the Parallel ATA interface. • Hot plug support for Serial ATA drive and connections is not available on this motherboard. • Install Windows® XP Service Pack 1 or later versions when using Serial ATA drives. 4.
5. CPU, Power and Chassis Fan Connectors (4-pin CPU_FAN, 3-pin CHA_FAN1, 3-pin CHA_FAN2 ) The fan connectors support cooling fans of 350mA~740mA (8.88W max.) or a total of 1A~2.22A (26.64W max.) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Lack of sufficient air flow within the system may damage the motherboard components.
7. ATX power connectors (24-pin ATXPWR, 4-pin ATX12V) These connectors are for ATX 12V power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. In addition to the 24-pin ATX power connector, this motherboard requires that you connect the 4-pin ATX +12V power plug to provide sufficient power to the CPU. • Do not forget to connect the 4-pin ATX +12V power plug.
2-28 USB56 1 USB+5V USB_P7USB_P7+ GND 1 M2V USB 2.0 Connectors USB+5V USB_P6 USB_P6+ GND NC USB78 USB+5V USB_P5USB_P5+ GND M2V USB+5V USB_P8USB_P8+ GND NC 8. USB headers (10-1 pin USB56, USB78) If the USB ports on the rear panel are inadequate, a USB header is available for additional USB ports. The USB header complies with USB 2.0 specification that supports up to 480 Mbps connection speed. This speed advantage over the conventional 12 Mbps on USB 1.
9. Front panel audio connector (10-1 pin FP_AUDIO) This is an interface for the front panel audio cable that allows convenient connection and control of audio devices. AAFP AGND NC NC NC Legacy AC 97 compliant definition SENSE2_RETUR GND PRESENCE# SENSE1_RETUR Azalia compliant definition MIC2 MICPWR Line out_R NC Line out_L PORT1 L PORT1 R PORT2 R SENSE_SEND PORT2 L M2V M2V Analog Front Panel Connector 10.
• System Power LED Lead (3-1 pin PLED) This 3-1 pin connector connects to the system power LED. The LED lights up when you turn on the system power, and blinks when the system is in sleep mode. • System Warning Speaker Lead (4-pin SPEAKER) This 4-pin connector is for the case-mounted speaker. It allows you to hear system beeps and warnings. • Reset Switch Lead (2-pin RESET) This 2-pin connector is for the case-mounted reset switch to reboot the system without turning off the system power.
Chapter 3 This chapter describes the power up sequence, the vocal POST messages and ways of shutting down the system.
Chapter summary 3.1 Starting up for the first time............................3-1 3.2 Powering off the computer..............................
3.1 Starting up for the first time 1. After making all the connections, replace the system case cover. 2. Make sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: a. Monitor b. External SCSI devices (starting with the last device on the chain) c.
3.2 Powering off the computer 3.2.1 Using the OS shut down function If you are using Windows® 2000/XP: 1. Click the Start button then click Shut Down... 2. Make sure that the Shut down option button is selected, then click the OK button to shut down the computer. 3. The power supply should turn off after Windows® shuts down. If you are using Windows® XP: 1. Click the Start button then select Turn Off Computer. 2. Click the Turn Off button to shut down the computer. 3.
Chapter 4 This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
Chapter summary 4.1 Managing and updating your BIOS................4-1 4.2 BIOS Setup program........................................4-9 4.3 Main menu.......................................................4-12 4.4 Advanced menu..............................................4-15 4.5 Power menu....................................................4-25 4.6 Boot menu.......................................................4-29 4.7 Tools menu.....................................................4-34 4.
4.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. ASUS AFUDOS - Updates the BIOS using a bootable floppy disk in DOS mode. 2. ASUS EZ Flash - Updates the BIOS using a floppy disk during POST. 3. ASUS CrashFree BIOS 3 - Updates the BIOS using a bootable floppy disk or the motherboard support CD. 4. ASUS Update - Updates the BIOS in a Windows® environment.
2. Copy the original (or the latest) motherboard BIOS to the bootable floppy disk. 4.1.2 Using AFUDOS to update the BIOS To update the BIOS using the AFUDOS.EXE utility: 1. Visit the ASUS website to download the latest BIOS file for your motherboard. Save the BIOS file to a bootable floppy disk. Write the BIOS file name on a piece of paper. You need to type the exact BIOS file name at the prompt. 2. Copy the AFUDOS.EXE utility from the support CD to the bootable floppy disk that contains the BIOS file. 3.
When the BIOS update process is complete, the utility returns to the DOS prompt. A:\>afudos /iM2V.ROM AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading file ..... done Erasing flash .... done Writing flash .... 0x0008CC00 (9%) Verifying flash .. done A:\> 6. Reboot the system from the hard disk. 4.1.3 Using AFUDOS to copy BIOS from PC You can use the AFUDOS.
3. The utility will copy the current system BIOS by default to the floppy disk. Make sure that the floppy disk has at least 600KB of free disk space and is not write-protected. A:\>afudos /oMYBIOS03.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading flash ..... done A:\> When the copy process is complete, the utility returns to the DOS prompt. 4.1.
4. Insert the floppy disk that contains the BIOS file. If all the necessary files are found in the floppy disk, EZ Flash performs the BIOS update process and automatically reboots the system when done. DO NOT shut down or reset the system while updating the BIOS! Doing so can cause system boot failure! User recovery requested. Starting BIOS recovery... Checking for floppy... Floppy found! Reading file “M2V.ROM”. Completed. Start flashing... Flashed successfully. Rebooting. 4.1.
When found, the utility reads the BIOS file and starts flashing the corrupted BIOS file. Award BootBlock BIOS v1.0 Copyright (c) 2000, Award Software, Inc. BIOS ROM checksum error Detecting IDE ATAPI device... Found CDROM, try to Boot from it... Pass 4. Restart the system after the utility completes the updating process. Recovering the BIOS from the USB flash disk To recover the BIOS from the USB flash disk: 1. Insert the USB flash disk that contains BIOS file to the USB port. 2. Turn on the system.
4.1.6 ASUS Update The ASUS Update is a utility that allows you to update the motherboard BIOS in Windows® environment. This utility is available in the support CD that comes with the motherboard package. ASUS Update requires an Internet connection either through a network or an Internet Service Provider (ISP). To install ASUS Update: 1. Insert the support CD into the CD-ROM drive. The Drivers menu appears. 2. Click the Utilities tab, then click Install ASUS Update VX.XX.XX.
3. If you select updating/ downloading from the Internet, select the ASUS FTP site nearest you to avoid network traffic, or choose Auto Select. Click Next. 4. From the FTP site, select the BIOS version that you wish to download. Click Next. 5. Follow the instructions on the succeeding screens to complete the update process. 6. If you select the option to update the BIOS from a file, a window prompts you to locate the file.
4.2 BIOS Setup program This motherboard supports a programmable firmware chip that you can update using the provided utility described in section “4.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you may want to change the configuration of your computer in the future.
4.2.1 BIOS menu screen Menu items Menu bar Configuration fields System Time [11:51:19] System Date [Thu 08/05/2003] Legacy Diskette A [1.44M, 3.5 in] Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave SATA 1 SATA 2 IDE Configuration : : : : : : [Not [Not [Not [Not [Not [Not Detected] Detected] Detected] Detected] Detected] Detected] General help Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time.
4.2.4 Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting Main shows the Main menu items. The other items (Advanced, Power, Boot, and Exit) on the menu bar have their respective menu items. System Time System Date Legacy Diskette A Language Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave SATA 1 SATA 2 IDE Configuration [11:10:19] [Thu 03/27/2003] [1.44M, 3.
4.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information. Refer to section “4.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them. System Time [11:51:19] System Date [Thu 08/05/2003] Legacy Diskette A [1.44M, 3.
4.3.4 Primary and Secondary IDE Master/Slave While entering Setup, BIOS auto-detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press to display the IDE device information.
PIO Mode [Auto] Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] Selects the DMA mode. Configuration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] SMART Monitoring [Auto] Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled] 32Bit Data Transfer [Disabled] Enables or disables 32-bit data transfer.
4.4 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Take caution when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. JumperFree Configuration USB Configuration CPU Configuration Chipset Onboard Devices Configuration PCI PnP 4.4.
The following item appears only when the AI Overclocking item is set to [Manual]. FSB Frequency [200] The valid input value is from 200 to 400. PLL1 Spread Spectrum [Enabled] Allows you to enable or disable the PLL1 Spread Spectrum. Configuration options: [Enabled] [Disabled] DDR Voltage [1.90V] Sets the DDR Voltage. Configuration options: [1.80V] [1.85V] [1.90V] [1.95V] 4.4.2 USB Configuration The items in this menu allows you to change the USB-related features.
Legacy USB Support [Enable] Allows you to enable or disable support for USB devices on legacy operating systems (OS). Setting to Auto allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled. Configuration options: [Disabled] [Enabled] [Auto] Port 64/60 Emulation [Enabled] Allows you to enable or disable the Port 64/60 Emulation.Configuration options: [Disabled] [Enabled].
MTRR Mapping [Continuous] This option determines the method used for programming CPU MTRRs when 4GB or more memory is present. Discrete leaves the PCI hole below the 4GB boundary undescribed. Continuous explicitly describes the PCI hole as non-cachable Runtime Legacy PSB [Disabled] Allows you to enable or disable the Runtime Legacy PSB. Configuration options: [Disabled] [Enabled] Cool N’Quiet [Disabled] Enables or disables the AMD Cool ‘n’ Quiet! technology feature.
MCT Timing Mode [Auto] Appears only when the Parallel Port Mode is set to [ECP]. This item allows you to set the Parallel Port ECP DMA. Configuration options: [DMA0] [DMA1] [DMA3] Bank Interleacving [Auto] Sets whether to allow memory accesses to be spread out over BANKS on the same node or across nodes, decreasing access contention. Configuration options: [Disabled] [Enabled] MemClk Tristate C3/ATLVID [Disabled] Allows you to enable or disable the MemCLK Tri-Stating During C3 and Alt VID.
Sets the system to correct DRAM ECC Errors immediately when they occur, even if background scrubbing is on. Configuration options: [Disabled] [Enabled] DRAM BG Scrub [Disabled] Disables or sets the DRAM scrubbing functionality that corrects and rewrites memory errors so later reads are correct. During this while the memory is not being used improves performance. Configuration options: [Disabled] [40ns] [80ns] [160ns] [320ns] [640ns] [1.28us] [2.56us] [5.12us] [10.2us] [20.5us] [41.0us] [81.9us] [163.
4.4.4 Chipset The Chipset menu items allow you to change the advanced chipset settings. Select an item then press to display the sub-menu. Advanced Chipset Settings WARNING: Setting wrong values in below sections may to malfunction.
4.4.
ECP Mode DMA Channel [DMA3] Allows you to select the Parallel Port ECP DMA. Configuration options: [DMA0] [DMA1] [DMA3] Parallel Port IRQ [IRQ7] Allows you to select the Parallel Port IRQ. Configuration options: [IRQ5] [IRQ7] 4.4.6 PCI PnP The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices.
PCI Latency Timer [64] Allows you to select the value in units of PCI clocks for the PCI device latency timer register. Configuration options: [32] [64] [96] [128] [160] [192] [224] [248] Allocate IRQ to PCI VGA [Yes] When set to [Yes], BIOS assigns an IRQ to PCI VGA card if the card requests for an IRQ. When set to [No], BIOS does not assign an IRQ to the PCI VGA card even if requested.
4.5 Power menu The Power menu items allow you to change the settings for the Advanced Power Management (APM) feature. Select an item then press to display the configuration options. Suspend Mode [Auto] Repost Video on S3 Resume [No] ACPI 2.0 Support [ACPI v1.0] ACPI APIC Support [Enabled] Select the ACPI state used for System Suspend. APM Configuration Hardware Monitor 4.5.1 Suspend Mode [Auto] Allows you to select the ACPI state to be used for system suspend.
4.5.5 APM Configuration APM Configuration Power Button Mode [On/Off] Restore on AC Power Loss [Power Off] Power Power Power Power Power Power On On On On On On By By By By By By External Modems [Disabled] Lan [Disabled] PCI Devices [Disabled] PS/2 Keyboard [Disabled] PS/2 Mouse [Disabled] RTC Alarm [Disabled] Power Button Mode [On/Off] Allows the system to go into On/Off mode or suspend mode when the power button is pressed.
Power On By PCI Devices [Disabled] Allows you to enable or disable the PME# to generate a wake event. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Enabled] Power On By PS/2 Keyboard [Disabled] Allows you to enable or disable the keyboard wake-up feature. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead.
CPU Temperature [xxx ºC/xxx ºF] MB Temperature [xxx ºC/xxx ºF] The onboard hardware monitor automatically detects and displays the CPU, motherboard and power temperatures. Select Disabled if you do not wish to display the detected temperatures. CPU Fan Speed [xxxxRPM] or [N/A] Chassis Fan Speed [xxxxRPM] or [N/A] The onboard hardware monitor automatically detects and displays the CPU and chassis fan speeds in rotations per minute (RPM).
4.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press to display the sub-menu. Boot Settings Boot Device Priority Removable Drives Boot Settings Configuration Security Specifies the Boot Device Priority sequence. 4.6.1 Boot Device Priority Boot Device Priority 1st Boot Device [1st FLOPPY DRIVE] 2nd Boot Device [Hard Drive] 3rd Boot Device [ATAPI CD-ROM] Specifies the boot sequence from the available devices.
4.6.2 Boot Settings Configuration Boot Settings Configuration Quick Boot [Enabled] Full Screen Logo [Enabled] AddOn ROM Display Mode [Force BIOS] Bootup Num-Lock [On] PS/2 Mouse Support [Auto] Wait for ‘F1’ If Error [Enabled] Hit ‘DEL’ Message Display [Enabled] Interrupt 19 Capture [Disabled] Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system.
Hit ‘DEL’ Message Display [Enabled] When set to Enabled, the system displays the message “Press DEL to run Setup” during POST. Configuration options: [Disabled] [Enabled] Interrupt 19 Capture [Disabled] When set to [Enabled], this function allows the option ROMs to trap Interrupt 19. Configuration options: [Disabled] [Enabled] 4.6.3 Security The Security menu items allow you to change the system security settings. Select an item then press to display the configuration options.
To clear the supervisor password, select the Change Supervisor Password then press . The message “Password Uninstalled” appears. If you forget your BIOS password, you can clear clear it by erasing the CMOS Real Time Clock (RTC) RAM. See section “2.6 Jumpers” for information on how to erase the RTC RAM. After you have set a supervisor password, the other items appear to allow you to change other security settings.
Change User Password Select this item to set or change the user password. The User Password item on top of the screen shows the default Not Installed. After you have set a password, this item shows Installed. To set a User Password: 1. Select the Change User Password item and press . 2. On the password box that appears, type a password combination of at least six (6) letters and/or numbers, then press . 3. Confirm the password when prompted.
4.7 Tools menu The Tools menu items allow you to store or load multiple BIOS settings. Tools O.C. PROFILE Configuration O.C. Profile1 Status :Not Installed O.C. Profile2 Status :Not Installed Save to Profile 1 Load from Profile 1 Save to Profile 2 Load from Profile 2 Start O.C. Profile Save to/Load from Profile 1 Allows you to save Multi-language BIOS settings to profile1 or load BIOS file from profile1.
4.8 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items. Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Load Setup Defaults Exit system setup after saving the changes. F10 key can be used for this operation. Pressing does not immediately exit this menu. Select one of the options from this menu or from the legend bar to exit.
Discard Changes Allows you to discard the selections you made and restore the previously saved values. After selecting this option, a confirmation appears. Select Yes to discard any changes and load the previously saved values. Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press , a confirmation window appears. Select Yes to load default values.
Chapter 5 This chapter describes the contents of the support CD that comes with the motherboard package.
Chapter summary 5.1 Installing an operating system........................5-1 5.2 Support CD information...................................5-1 5.3 Software Information.......................................5-8 5.4 RAID configurations.......................................5-10 5.5 Creating a RAID driver disk...........................5-19 5.6 Cool ‘n’ Quiet!™ Technology........................
5.1 Installing an operating system This motherboard supports Windows® 2000/XP/2003 Server operating systems (OS). Always install the latest OS version and corresponding updates to maximize the features of your hardware. Motherboard settings and hardware options vary, so use the setup procedures presented in this chapter for general reference only. Refer to your OS documentation for more information. 5.
5.2.2 Drivers menu The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. AMD Cool ‘n’ Quiet Driver Installs the AMD Cool ‘n’ Quiet!™ Technology driver. VIA Chipset Driver Program Installs the VIA Chipset Driver Program. Realtek Audio Driver Installs the Realtek® audio controller and application. Attansic L1 Gigabit Ethenet Driver Installs the Attansic L1 Gigabit Ethenet driver.
5.2.3 Utilities menu The Utilities menu shows the applications and other software that the motherboard supports. ASUS Cool ‘n’ Quiet Utility Installs the Cool ‘n’ Quiet! Technology software. ASUS PC Probe II This smart utility monitors the fan speed, CPU temperature, and system voltages, and alerts you of any detected problems. This utility helps you keep your computer in healthy operating condition. ASUS Update Allows you to download the latest version of the BIOS from the ASUS website.
Microsoft DirectX 9.0c Installs the Microsoft® DirectX 9.0c driver. The Microsoft DirectX® 9.0c is a multimedia technology that enhances computer graphics and sound. DirectX® improves the multimedia features of you computer so you can enjoy watching TV and movies, capturing videos, or playing games in your computer. Visit the Microsoft website (www.microsoft.com) for updates. Anti-virus Utility The anti-virus application scans, identifies, and removes computer viruses.
5.2.5 Manuals menu The Manuals menu contains a list of supplementary user manuals. Click an item to open the manual. Install the Adobe® Acrobat® Reader from the Utilities menu to open the manual files in PDF. 5.2.6 ASUS Contact information Click the Contact tab to display the ASUS contact information. You can also find this information on the inside front cover of this user guide.
5.2.7 Other information The icons on the top right corner of the screen give additional information on the motherboard and the contents of the support CD. Click an icon to display the specified information. Motherboard Info Displays the general specifications of the motherboard. Browse this CD Displays the support CD contents in graphical format.
Technical Support Form Displays the ASUS Technical Support Request Form that you have to fill out when requesting technical support. Filelist Displays the contents of the support CD and a brief description of each in text format.
5.3 Software Information Most of the applications in the support CD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software for more information. This section provides details of the software applications that the motherboard supports. ASUS MyLogo2™ The ASUS MyLogo2™ is automatically installed when you install the ASUS Update utility from the software menu. See section “5.2.3 Utilities menu”.
4. From the selection that appears, choose a logo image. Click Next. You can create your own boot logo image in GIF, JPG, or BMP file formats. 5. When you click on an image, it displays larger on the MyLogo2™ screen. • ASUS MyLogo2™ might encounter problems with complex images. If a problem occurs, replace with a simpler image or make the image smaller. • To reduce the logo image, click on the arrow on the Ratio item and select your desired scale. 6.
5.4 RAID configurations The motherboard comes with the VIA VT8237A controller integrated in the SouthBridge to support Redundant Array of Independent Disks (RAID) configurations. Using two Serial ATA hard disks, you can set up RAID 0, RAID 1, and JBOD configurations. The following defines the different RAID set configurations: RAID 0 (called data striping) optimizes two identical hard disk drives to read and write data in parallel, interleaved stacks.
5.4.1 Installing hard disks The motherboard supports UltraDMA 133/100/66 and Serial ATA hard disk drives. For optimal performance, install identical Serial ATA hard disks of the same model and capacity when creating a disk array. • If you are creating a RAID 0 (striping) array for performance, use two new drives. • If you are creating a RAID 1 (mirroring) array for protection, you can use two new drives or use an existing drive and a new drive with the same or larger size than the existing drive.
5.4.2 VIA RAID configurations The motherboard includes a high performance IDE RAID controller integrated in the VIA VT8237A southbridge chipset. It supports RAID 0 and RAID 1 with two independent Serial ATA channels. Refer to VIA8237 SATA Quick Setup guide found in the support CD for detailed information on RAID configurations under different operating systems. Entering VIA Tech RAID BIOS Utility 1. Boot-up your computer. 2. During POST, press to enter VIA RAID configuration utility.
Create Array 1. From the VIA RAID BIOS utility main menu, select Create Array then press . The main menu items on the upper-left corner of the screen are replaced with create array menu options. VIA Tech. RAID BIOS Ver 1.
4. Press to confirm or to return to the configuration options. If you selected , proceed to step 9. 5. Select Select Disk Drives, then press . Use arrow keys to select disk drive, then press to mark selected drive. An asterisk appears before a selected drive. 6. Select Block Size, then press to set array block size. A list of valid array block sizes are displayed on a pop-up menu. TIP: For server systems, use of a lower array block size is recommended.
3. From this point, you can auto-configure the RAID array by selecting Auto Setup for Data Security or manually configure the RAID array for mirrored sets. If you want to auto-configure, proceed to the next step, otherwise, skip to step 6. 4. Select Auto Setup for Data Security and press . The following confirmation message appears. Auto create array will destroy all data on disks, Continue? (Y/N) 5. Press to confirm or to return to the configuration options.
RAID Span for capacity 1. From the create array menu, select Array Mode, then press . The supported RAID configurations appear on a pop-up menu. RAID RAID RAID RAID 0 for performance 1 for data protection 0/1 SPAN for capacity 2. Select RAID SPAN for capacity then press . 3. From this point, you can auto-configure the RAID array by selecting Auto Setup for Capacity or manually configure the RAID array for spanned sets.
10. Press to confirm or to return to the configuration options. 11. Press to go back to main menu. Delete Array 1. From the VIA RAID BIOS utility main menu, select Delete Array then press . VIA Tech. RAID BIOS Ver 1.
Serial Number View 1. From the VIA RAID BIOS utility main menu, select Serial Number View then press . 2. From the list of channel used for IDE RAID arrays, use the arrow keys to move the selection bar on each item. The serial number for the selected drive is displayed at the bottom of the screen. This option is useful for identifying same model disks. VIA Tech. RAID BIOS Ver 1.
5.5 Creating a RAID driver disk A floppy disk with the RAID driver is required when installing Windows® XP/2000 operating system. You can create a RAID driver disk using Makedisk.exe utility. To create a RAID driver disk: 1. Insert the motherboard support CD into the CD-ROM drive and locate the Makedisk.exe utility in “\Drivers\Chipset\drvdisk\Makedisk.exe” of the motherboard support CD. 2. Insert a clean floppy disk into the floppy disk drive and execute Makedisk.exe.
5.6 Cool ‘n’ Quiet!™ Technology The motherboard supports the AMD Cool ‘n’ Quiet!™ Technology that dynamically and automatically change the CPU speed, voltage, and amount of power depending on the task the CPU performs. 5.6.1 Enabling Cool ‘n’ Quiet!™ Technology To enable Cool ‘n’ Quiet!™ Technology: 1. Turn on the system and enter BIOS by pressing the key during the Power On Self-Tests (POST). 2.
5.6.2 Launching the Cool ‘n’ Quiet!™ software The motherboard support CD includes the Cool ‘n’ Quiet!™ software that enables you to view your system’s real-time CPU Frequency and voltage. Make sure to install the Cool ‘n’ Quiet!™ software from the motherboard support CD. Refer to section “5.2.3 Utilities menu”, for details. To launch the Cool ‘n’ Quiet!™ program: 1. If you are using Windows® 98SE/ME/2000, click the Start button. Select Programs > ASUS > Cool & Quiet > Cool & Quiet. 2.
5-22 Chapter 5: Software support
