用戶手冊 Motherboard M4A78
C4507 第一版 2009 年 2 月發行 版權所有‧不得翻印 © 2009 華碩電腦 本產品的所有部分,包括配件與軟件等,其相關知識產權等歸華碩電腦公司(以 下簡稱華碩)或授權華碩使用的相關主體所有,未經權利主體許可,不得任意地仿 製、拷貝、摘抄或轉譯。本用戶手冊沒有任何型式的擔保、立場表達或其它暗示。若 有任何因本用戶手冊或其所提到之產品信息,所引起直接或間接的數據流失、利益損 失或事業終止,華碩及其所屬員工恕不為其擔負任何責任。除此之外,本用戶手冊所 提到的產品規格及信息只作參考,內容亦會隨時更新,恕不另行通知。 下列因素導致的產品故障或損壞不在免費保修範圍內: A. 因天災(水災、火災、地震、雷擊、颱風等)、遇不可抗拒外力或人為之操作使 用不慎造成之損害。 B. 自行拆裝、修理、或將產品送至非華碩認証之維修點進行檢測維修。 C. 用 戶擅自或請第三人修改、修復、變更規格及安裝、添加、擴充非本公司原廠 銷售、授權或認可之配件所引起之故障與損壞。 D. 因用戶自行安裝軟件及設定不當所造成之使用問題及故障。 E. 計算機病毒所造成之問題及故障。 F.
三年質保 全國聯保 華碩產品質量保證卡 尊敬的華碩產品用戶: 首先非常感謝您選用華碩公司產品,讓我們有機會向您提供優質的服務。為了使我們的服務讓 您更滿意,在購買後請您認真閱讀此說明並妥善保存此質量保證卡。 保修說明注意事項: 一、 請將此質量保證卡下方的用戶資料填寫完整,並由最終直接經銷商加蓋印章,如果沒有加蓋 印章,請找原購買處補蓋以保障您的權益。請務必保留購買發票或複印件,否則華碩公司將 以產品的出廠日期為參照進行保修。 二、 華碩公司對在中國大陸地區(不包括港澳台地區)發售的、經合法渠道銷售給消費者的華碩 主板及顯卡產品實行三年的免費保修服務。 三、 若經本公司判斷屬下列因素,則不屬於免費保修服務的範圍,本公司將有權利收取維修費 請用剪刀沿虛線剪下 用: A. 超過華碩提供的質保有效期的主板、顯卡產品。 B. 因遇不可抗拒外力(如:水災、火災、地震、雷擊、颱風等)或人為之操作使用不慎 造成之損害。 C. 未按產品說明書條例的要求使用、維護、保管而造成的損壞。 D. 用戶擅自或請第三方人員自行檢修、改裝、變更組件、修改線路等。 E. 因用戶自行安裝軟件即設定不當所造成之使用問題及故障。 F.
目錄內容 安全性須知.................................................................................................................................. viii 電氣方面的安全性......................................................................................................... viii 操作方面的安全性......................................................................................................... viii 關於這本用戶手冊.....................................................................................................................
目錄內容 1.11 軟件支持........................................................................................................................1-30 1.11.1 安裝操作系統..............................................................................................1-30 1.11.2 驅動程序與應用程序光盤信息..............................................................1-30 第二章:BIOS 信息 2.1 2.2 2.3 2.4 2.5 vi 管理、更新您的 BIOS 程序..................................................................................... 2-1 2.1.
目錄內容 2.6 啟動菜單(Boot)....................................................................................................2-18 2.6.1 2.7 2.8 啟動設備順序(Boot Device Priority)...........................................2-18 2.6.2 啟動選項設置(Boot Settings Configuration)............................2-18 2.6.3 安全性菜單(Security).........................................................................2-19 工具菜單(Tools)...................................................................................................
安全性須知 電氣方面的安全性 • 為避免可能的電擊造成嚴重損害,在搬動電腦主機之前,請先將電腦電源線暫時 從電源插槽中拔掉。 • 當您要加入硬件設備到系統中或者要移除系統中的硬件設備時,請務必先連接該 設備的數據線,然後再連接電源線。可能的話,在安裝硬件設備之前先拔掉電腦 的電源線。 • 當您要從主板連接或拔除任何的數據線之前,請確定所有的電源線已事先拔掉。 • 在使用擴展卡或適配卡之前,我們建議您可以先尋求專業人士的協助。這些設備 有可能會干擾接地的迴路。 • 請確定電源的電壓設置已調整到本國/本區域所使用的電壓標準值。若您不確定您 所屬區域的供應電壓值為何,那麼請就近詢問當地的電力公司人員。 • 如果電源已損壞,請不要嘗試自行修復。請將之交給專業技術服務人員或經銷商 來處理。 操作方面的安全性 • 在您安裝主板以及加入硬件設備之前,請務必詳加閱讀本手冊所提供的相關信 息。 • 在使用產品之前,請確定所有的數據線、電源線都已正確地連接好。若您發現有 任何重大的瑕疵,請儘快聯絡您的經銷商。 • 為避免發生電氣短路情形,請務必將所有沒用到的螺絲、回形針及其他零件收 好,不要遺留在主板上或電腦
提示符號 為了能夠確保您正確地完成主板設置,請務必注意下面這些會在本手冊中出現的 標示符號所代表的特殊含意。 警告:提醒您在進行某一項工作時要注意您本身的安全。 小心:提醒您在進行某一項工作時要注意勿傷害到電腦主板元件。 重要: 此符號表示您必須要遵照手冊所描述之方式完成一項或多項軟硬件的安 裝或設置。 注意:提供有助於完成某項工作的訣竅和其他額外的信息。 跳線帽及圖示說明 主板上有一些小小的塑膠套,裡面有金屬導線,可以套住選擇區的任二隻針腳 (Pin)使其相連而成一通路(短路),本手冊稱之為跳線帽。 有關主板的跳線帽使用設置,茲利用以下圖示說明。以下圖為例,欲設置 為“Jumper™ Mode”,需在選擇區的第一及第二隻針腳部分蓋上跳線帽,本手冊圖 示即以塗上底色代表蓋上跳線帽的位置,而空白的部 分則代表空接針。以文字表示為:[1-2]。 2 3 1 2 因此,欲設置為“JumperFree™ Mode”,以右圖 表示即為在“第二及第三隻針腳部分蓋上跳線帽”, 以文字表示即為:[2-3]。 Jumper Mode Jumper Free (Default) 哪裡可以找到更多的產品信息 您可以通過
電子信息產品污染控制標示:圖中之數字為產品之環保使用期限。 僅指電子信息產品中含有的有毒有害物質或元素不致發生外洩或突變 從而對環境造成污染或對人身、財產造成嚴重損害的期限。 有毒有害物質或元素的名稱及含量說明標示: 有害物質或元素 部件名稱 鉛(Pb) 汞(Hg) 鎘(Cd) 六價鉻 (Cr(VI)) 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) 印刷電路板及其電 子組件 × ○ ○ ○ ○ ○ 外部信號連接頭及 線材 × ○ ○ ○ ○ ○ ○: 表示該有毒有害物質在該部件所有均質材料中的含量均在 SJ/T 11363-2006 標 准規定的限量要求以下。 ×: 表示該有毒有害物質至少在該部件的某一均質材料中的含量超出 SJ/T 113632006 標准規定的限量要求,然該部件仍符合歐盟指令 2002/95/EC 的規范。 備註:此產品所標示之環保使用期限,係指在一般正常使用狀況下。
M4A78 規格列表 中央處理器 支持 Phenom™ X4 / Phenom™ X3 / Athlon™ X2 / Athlon™ / Sempron™ 處理器(AM2+/AM2 CPU) 兼容 Phenom™ II / Athlon™ X4 / Athlon™ X3 / Athlon™ X2(AM3 CPU) 支持 AMD Cool ‘n’ Quiet™ 技術 支持中央處理器高達 125W * 請瀏覽 http://www.asus.com.cn 獲取 AMD 中央處理器支持列表 芯片組 AMD 770 / SB700 系統總線 高達 5200 MT/s;HyperTransport™ 3.0 接口,支持 AM2+ / AM3 CPU 內存 支持雙通道內存架構 4 x 240-pin 內存插槽,最大支持 16GB unbuffered ECC DDR2 1066*/800/667/533MHz 內存條 * 僅 AM2+ / AM3 處理器支持 DDR2 1066. ** 請瀏覽 www.asus.com.
M4A78 規格列表 內置 I/O 設備接口 3 x USB 2.0/1.1 擴展套件數據線插槽,可擴展六組外接式 USB 2.0/1.1 接口 1 x IDE 設備連接插座 5 x SATA 設備連接插座 1 x 高保真前面板音頻連接排針 1 x 系統控制面板連接排針 1 x 內置音頻信號接收插槽(CD) 1 x S/PDIF Out 數字音頻連接排針 1x 中央處理器 / 機箱 / 電源 風扇電源插槽 24-pin ATX 主板電源插槽 4-pin ATX 12V 主板電源插槽 BIOS 功能 8Mb Flash ROM、AMI BIOS、PnP、DMI v2.0、WfM2.0、 ACPI2.0a、SM BIOS v2.5 相關配件 1 x Serial ATA數據線 1 x UltraDMA 133/100 數據線 1x I/O 擋板 1 x 用戶手冊 主板尺寸 ATX 型式:12 x 8.2 英寸(30.6 x 20.
第一章 產品介紹 1.1 歡迎加入華碩愛好者的行列 再次感謝您購買此款華碩 M4A78 主板! 本主板的問世除了再次展現華碩對於主板一貫具備的高質量、高性能以及高穩定 度的嚴苛要求,同時也添加了許多新的功能以及大量應用在它身上的最新技術,使得 M4A78 主板成為華碩優質主板產品線中不可多得的閃亮之星。 在您拿到本主板包裝盒之後,請馬上檢查下面所列出的各項標準配件是否齊全。 1.2 產品包裝 主板 華碩 M4A78 主板 排線 1 x Serial ATA 數據線 1 x Ultra DMA 133/100 數據線 配件 1 x I/O 擋板 應用程序光盤 華碩主板驅動程序與應用程序光盤 相關文件 用戶手冊 若以上列出的任何一項配件有損壞或是短缺的情形,請儘快與您的經銷 商聯係。 1.3 特殊功能 1.3.
支持 HyperTransport™ 3.0 HyperTransport™ 3.0 提供高於 HT1.0 2.
PCI Express 架構 PCI Express™ 為目前最新的內接 I/O 技術,並被視為 PCI 總線的 革新性升級。PCI Express 接口的特色在于可提供兩部內接設備點對 點內部串行連接,至于資料則是以封包的方式進行傳遞,通過這種 數据傳輸方式,傳輸速率可得到大幅度的提升。除了更高的數据傳 輸性能,此高速串行接口也可與既有的 PCI 接口規格的軟件兼容。 支持 SATA on the Go 本主板通過 Serial ATA 接口支持 SATA 3Gb/s 技術,相較於 之前的 Serial ATA,Serial ATA 3Gb/s 的傳輸帶寬加倍。外接式 的 SATA 連接端口位於後側面板,並支持熱插拔功能讓您更易於安 裝。您可以輕鬆的將照片、影片或其他娛樂內容備份至外接設備。 後面板 S/PDIF 數字音頻輸出端口 本主板通過 S/PDIF 接針支持 S/PDIF (SONY-PHILIPS 數字 接口) 輸出。您可直接傳輸數字音頻信號,而無需轉換成模擬信號 格式,從而保證最佳音頻質量。 支持 Serial ATA 3Gb/s 技術 本主板通過 Serial ATA 接口支持 SATA
華碩 Express Gate Express Gate 是內置於主板的獨特操作系統。5秒就能啟動, 開機後不用進入 Windows® 操作系統就可立即連上網絡或使用一些 常用的應用程序。 • 華碩 Express Gate 支持從 SATA 硬盤、光驅與 USB 閃存盤中上傳 文件,但僅可下載至 USB 閃存盤。 • 實際啟動時間依硬件配置與型號而定。 •對於 SSD 版本, Express Gate 是內置於主板中的,所以您無需通 過進入 Windows® 操作系統或硬盤就可連上網絡。 華碩 MyLogo2™ 個性化應用軟件 您可以將您最喜歡的照片轉換成 256 色開機畫面,創造一個更 加多彩和生動的屏幕畫面。 華碩 CrashFree BIOS 3 程序 華碩自行研發的 CrashFree BIOS 3 工具程序,可以讓您輕鬆 的恢復 BIOS 程序中的數據。當 BIOS 程序和數據被病毒入侵或毀 壞,您可以輕鬆的從備份磁盤或 USB 閃存盤中,將原始的 BIOS 數 據恢復至系統中。這項保護設備可以避免您因 BIOS 程序毀壞而需 購買 BIOS 芯片置換。 華碩 EZ Flash 2 程序 E
C.P.R. (CPU Parameter Recall) 由華碩獨家研發的 C.P.R. 功能,可以讓主板的 BIOS 程序在系 統因為超頻而導致死機時自動重新設置,將 CPU 的參數恢復為預 設值。當系統因為超頻而當機時,C.P.R.功能讓您不需開啟机箱, 就可以清除 RTC 資料。您只要輕鬆的將系統關機,重新開機啟動 系統之後,BIOS 程序就會自動恢復 CPU 設置中所有各項參數的默 認值。 1.
1.5 主板概觀 1.5.1 主板的擺放方向 當您安裝主板到電腦主機機箱內時,務必確認安裝的方向是否正確。主板的外接 插頭的方向應是朝向主機機箱的後方面板,而且您也會發現主機機箱後方面板會有相 對應的預留孔位。 1.5.
1.5.3 主板構造圖 1 2 3 4 5 6 4 20.9cm(8.2in) KBPWR KB_USB56 PWR_FAN ICS 9LPRS485 AUDIO AMD® 770 Realtek 8112 2 SATA1 SATA2 SATA3 SATA5 SATA6 PCIEX1_1 30.6cm(12.
1.6 中央處理器 (CPU) 本主板配置一組中央處理器插槽,是專為 AMD® AM3 Phenom™ II / Athon™ X4 / Athon™ X3 / Athlon™ X2 / processors and AM2+ / AM2 Phenom™ X4 / Phenom™ X3 / Athlon™ X2 / Athlon™ / Sempron™ 處理器所設計。 此中央處理器插槽不兼容 AMD® Opteron™ 處理器。請勿在此主板上安 裝 Opteron™ 處理器。 1.6.1 安裝中央處理器 請依照以下步驟安裝處理器: 1. 找到位於主板上的處理器插座。 M4A78 M4A78 CPU socket AM2+ 2.
3. 將中央處理器上標示有金三角的那一 端,對齊插槽左下角處也有三角標示的 地方(與處理器插座連接的地方,見右 圖所示)。 4. 請小心地放入中央處理器,並確定所有 的針腳是否都已沒入插槽內。 處理器只能以一個方向正確安 裝,請勿強制將處理器裝入插 槽,以避免弄彎處理器的針腳 和處理器本身! 小三角標示 金三角標示 5. 當處理器安置妥當,接下來在您要拉下 固定拉桿欲鎖上處理器插槽的同時,請 用手指輕輕地抵住處理器。最後當固定 拉桿鎖上插槽時會發出一清脆聲響,即 表示已完成鎖定。 6. 接著請依照散熱器包裝盒內的說明書 或“1.6.2 安裝散熱器與風扇”來安裝 散熱器與風扇。 7.
1.6.2 安裝散熱器與風扇 請確認您所使用的是經過 AMD 認證合格的散熱器與風扇。 請依照下面步驟安裝處理器的散熱器和風扇: 1. 將散熱器覆蓋在中央處理器上方,並且要注意散熱器應該要恰當地座落於支撐機 構底座範圍內。 • 本主板出貨時已安裝“支撐機構底座”。 • 在安裝中央處理器或其他元件到主板上時,不必將支撐機構底座移除。 • 若您購買散裝的處理器與散熱風扇組件,在您安裝散熱風扇前,請先確 定處理器表面已正確塗上適量的散熱膏。 CPU 風扇 CPU 散熱器 支撐底座固定托架 支撐機構底座 支撐底座固定把手 您所購買的盒裝中央處理器包裝盒中應已內附處理器、散熱器以及支撐機 構的安裝說明文件。如果本節中的指導說明與處理器內附說明文件有所不 符,則請以處理器內附的安裝說明文件為準。 2.
3. 再將另一邊的固定托架也扣在支撐底座上(靠近支撐底座固定把手),當固定托 架正確的扣住支撐機構底座時,會有一聲清脆的機構組合聲。 請確認處理器散熱器與風扇已正確安裝於主板的底座 上,如散熱器與風扇 安裝錯誤,則您將無法將固定托架與主板底座完整地扣合。 4. 最後再將支撐機構兩側上方的固定桿分別拉下鎖住,使得風扇和散熱器能緊密地 扣住支撐機構底座。 5. 將處理器風扇連接線插到主板上標示有“CPU_FAN”的電源插槽。 請勿忘記連接 CPU 風扇插座!若未連接可能會出現“Hardware monitoring error”的信息。 1.7 系統內存 1.7.
1.7.
DDR2-667MHz 支持內存插槽 容量 供應商 型號 SS/ DS CL 芯片型號 芯片廠牌 A* B* C* 2G Kingston KVR667D2N5/2G DS N/A 7RE22 D9HNL Micron · · · 512MB Kingston KVR667D2N5/512 SS N/A SO1237650821 SBP D6408TR4CGL25USL0749 05PECNB Kingston · · · 2G Kingston KVR667D2N5/2G DS N/A E1108ACBG-8E-E 0813A90CC Elpida · · · 1G Kingston KVR667D2N5/1G DS N/A SO1280420822 SOP D6408TR4CGL25USL1563 04PECXA Kingston · · · 512MB Qimonda HYS64T64000EU-3S-B2 SS 5 HYB18T512B00B2F3SFS S28171 Qimonda ·
DDR2-800MHz 支持內存插槽 容量 供應商 型號 SS/ DS CL 芯片型號 芯片廠牌 1G Kingston KHX6400D2LL/1G DS N/A Heat-Sink Package Kingston · · · 512MB Kingston KHX6400D2LLK2/1GN SS N/A Heat-Sink Package Kingston · · · 512MB Kingston KVR800D2N6/512 SS N/A E5108AJBG-8E-E Elpida · · · 1G Kingston KVR800D2N5/1G DS N/A D6408TR4CGL25USL362 406PECXA Kingston · · · 2G Kingston KVR800D2N5/2G DS N/A E1108ACBG-8E-E Elpida · · · 2G Kingston KHX6400D2/2G DS N/A Heat-Sink Package Kingst
支持內存插槽 容量 供應商 型號 SS/ DS CL 芯片型號 芯片廠牌 A* B* C* 2G PSC AL8E8F73C-8E1 DS 5 A3R1GE3CFF734MAA0E PSC · · · 2G PSC PL8E8F73C-8E1 DS 5 SHG772-AA3G PSC · · · 2G PSC PL8E8G73E-8E1 DS 5 XCP271A3G-A PSC · · · 2G PSC AL7E8E63H-10E1K DS 5 A3R1GE3CFF750RABBP(ECC) PSC · · · 1G GEIL GB22GB6400C4DC DS 4 GL2L64M088BA30EB GEIL · · · 1G GEIL GB24GB6400C4QC DS 4 GL2L64M088BA30EB GEIL · · · 1G GEIL GB22GB6400C5DC DS 5 GL2L64M088BA30EB GEIL · · · 1G G
DDR2-1066MHz 支持內存插槽 容量 供應商 型號 SS/ DS CL 芯片型號 芯片廠牌 A* B* 512MB Kingston KHX8500D2/512 SS N/A Heat-Sink Package Kingston · · 512MB Kingston KVR1066D2N7/512 SS N/A E5108AJBG-1J-E Elpida · · 512MB Kingston KHX8500D2K2/1GN SS N/A Heat-Sink Package Kingston · · 1G Kingston KHX8500D2K2/2GN DS N/A Heat-Sink Package Kingston · · 1G Kingston KVR1066D2N7/1G DS N/A E5108AJBG-1J-E Elpida · · 1G Kingston KHX8500D2/1G DS N/A Heat-Sink Package Kingston · · 1G
1.7.3 安裝內存條 安裝 / 取出內存條或其他的系統元件之前,請先暫時拔出電腦的電源適配 器。如此可避免一些會對主板或元件造成嚴重損壞的情況發生。 2 1. 先將 DDR2 內存條插槽兩端的卡 扣扳開。 DDR2 內存條缺口 2. 將內存條放在插槽上,使缺口對 准插槽的凸起點。 由於 DDR2 內存條金手指 部分均有缺口設計,因此 只能以一個固定方向安裝 到內存條插槽中。請勿強 制插入以免損及內存條。 1 1 向外扳開插槽兩端的卡扣 3. 最後緩緩將內存條插入插槽中, 若無錯誤,插槽兩端的卡扣會因 內存條安裝而自動扣到內存條兩 側的凹孔中。 3 卡扣會在內存條正確安裝後自動扣上 1.7.4 取出內存條 請依照以下步驟取出內存條: 1. 同時壓下內存條插槽兩端的固定 卡扣以鬆開內存條。 在壓下固定卡扣取出內存 條的同時,您可以用手指 頭輕輕地扶住內存條,以 免跳出而損及內存條。 2 1 1 DDR2 內存條缺口 2.
1.8 擴展插槽 為了因應未來會擴展系統機能的可能性,本主板提供了擴展插槽,在接下來的子 章節中,將會描述主板上這些擴展插槽的相關信息。 安裝 / 移除任何擴展卡之前,請暫時先將電腦的電源線拔出。如此可免除 因電氣殘留於電腦中而發生的意外狀況。 1.8.1 安裝擴展卡 請依照下列步驟安裝擴展卡: 1. 在安裝擴展卡之前,請先詳讀該擴展卡的使用說明,並且要針對該卡作必要的硬 件設置變更。 2. 鬆開電腦主機的機箱蓋並將之取下(如果您的主板已經放置在主機內)。 3. 找到一個您想要插入新擴展卡的空置插槽,並以十字螺絲起子鬆開該插槽位於主 機背板的金屬擋板的螺絲,最後將金屬擋板移出。 4. 將擴展卡上的金手指對齊主板上的擴展槽,然後慢慢地插入槽中,並以目視的方 法確認擴展卡上的金手指已完全沒入擴展槽中。 5. 再用剛才鬆開的螺絲將擴展卡將擴展卡固定在機箱內。 6. 將電腦主機的機箱蓋裝回鎖好。 1.8.2 設置擴展卡 在安裝好擴展卡之後,接著還須通過軟件設置來調整該擴展卡的相關設置。 1.
1.9 跳線選擇區 1. CMOS 配置數據清除(CLRTC) 在主板上的 CMOS 內存中記載著正確的時間與系統硬件配置等數據,這些數 據並不會因電腦電源的關閉而遺失數據與時間的正確性,因為CMOS 的電源是由 主板上的鋰電池所供應。 M4A78 CLRTC 1 2 2 3 Normal (Default) Clear RTC M4A78 Clear RTC RAM 想要清除這些數據,可以依照下列步驟進行: 1. 關閉電腦電源,拔掉電源線; 2. 將 CLRTC 跳線帽由 [1-2](默認值)改為 [2-3] 約五∼十秒鐘(此時即清 除 CMOS 數據),然後再將跳線帽改回 [1-2]; 3. 接上電源線,開啟電腦電源; 4.
2. 鍵盤 / 鼠標電源插槽 (3-pin KBPWR) 此跳線允許您開啟或關閉鍵盤 / 鼠標與 USB 接口 1-4 的喚醒功能。若您將跳 線帽設置為 [2-3 ](+5VSB),可通過點擊鼠標、使用 USB 設備或按下鍵盤上的 按鍵喚醒電腦(默認按鍵為空格鍵)。 要使用此功能,ATX 電源需提供至少1A / +5VSB 電壓,並在 BIOS 中進行相應設置。此跳線適用於後面板 USB 接口。 1 KBPWR 2 3 2 +5V (Default) +5VSB M4A78 M4A78 Keyboard Power Setting 3.
1.10 元件與外圍設備的連接 1.10.1 後側面板連接端口 1 2 15 14 13 3 4 12 11 5 6 7 8 10 9 1. PS/2 鍵盤 / 鼠標接口 (紫色):將 PS/2 鍵盤 / 鼠標插頭連接到此接口。 2. 並口:此 25-pin 端口可用於連接打印機、掃描儀或其他設備。 3. USB 2.0 設備接口 3 和 4:這二組 4-pin 通用串行總線(USB)接口可連接到使 用 USB 2.0 接口的硬件設備。. 4. LAN (RJ-45) 網絡接口:該接口可經 Gigabit 網線連接至 LAN 網絡。請參考下表 中各燈的說明。 網絡指示燈說明 Activity/Link 指示燈 狀態 描述 關閉 沒有連接 橘色 已連接 速度指示燈 狀態 描述 關閉 連接速度 10 Mbps 橘色 連接速度 100 Mbps 閃爍 綠色 數據傳輸中 ACT/LINK 指示燈 速度指 示燈 連接速度 1 Gbps 網絡接口 5. 中央聲道與重低音喇叭接口(橘色):這個接口可以連接中央聲道與重低音喇 叭。 6.
在 2、4、6、8 聲道音頻設置上,音頻輸出、音頻輸入與麥克風接頭的功 能會隨著聲道音頻設置的改變而改變,如下表所示。 二、四、六或八聲道音頻設置 四聲道 喇叭輸出 六聲道 喇叭輸出 八聲道 喇叭輸出 接頭 耳機/二聲道喇 叭輸出 淺藍色 聲音輸入端 聲音輸入端 聲音輸入端 聲音輸入端 草綠色 聲音輸出端 前置喇叭輸出 前置喇叭輸出 前置喇叭輸出 粉紅色 麥克風輸入端 麥克風輸入端 麥克風輸入端 麥克風輸入端 中央/重低音喇叭 輸出 橘色 – – 中央/重低音喇叭 輸出 黑色 – 後置喇叭輸出 後置喇叭輸出 後置喇叭輸出 灰色 – – – 側邊環繞喇叭輸出 請確認播放聲音的音頻設備為 Realtek High Definition Audio(此名稱可能 因操作系統不同而有差異)。請至【開始】>【控制面板】>【聲音和音頻 設備】>【聲音】來進行設置。 11. USB 2.0 設備接口 1 和 2:這二組 4-pin 通用串行總線(USB)接口可連接到使 用 USB 2.0 接口的硬件設備。 12.
1.10.2 內部接口 1. ATX 主板電源插槽(24-pin EATXPWR、4-pin ATX12V) 這些電源插槽用來連接到一個 ATX 電源供應器。電源供應器所提供的連接插 頭已經過特別設計,只能以一個特定方向插入主板上的電源插槽。找到正確的插 入方向後,僅需穩穩地將之套進插槽中即可。 M4A78 GND GND +12V DC +12V DC ATX12V EATXPWR +3 Volts +12 Volts +12 Volts +5V Standby Power OK GND PIN 1 +5 Volts GND +5 Volts GND +3 Volts +3 Volts GND +5 Volts +5 Volts +5 Volts -5 Volts GND GND GND PSON# GND -12 Volts +3 Volts PIN 1 M4A78 ATX power connectors • 建議您使用符合 ATX 12 V 2.
2.
3. Serial ATA 裝置連接插座 (7-pin SATA1、SATA2、SATA3、SATA5、SATA6) 本主板提供了新一代的連接插座,這個新一代的插座支持使用細薄的 Serial ATA 數據線連接主機內部主要的存儲設備。Serial ATA 3Gb/s 規格可向下兼容 Serial ATA 1.
4.
5. USB 擴展套件數據線插座 (10-1 pin USB78、USB910、USB1112) 這些 USB 擴展套件數據線插座支持 USB 2.0 規格,傳輸速率最高達 480Mbps , 比 USB 1.1(Full Speed)規格的 12 Mbps 快 40 倍,可以提供更高速的網絡連接、互 動式電腦游戲,還可以同時運行高速的外圍設備。 USB78 USB+5V USB_P8USB_P8+ GND NC USB+5V USB_P10USB_P10+ GND NC USB910 USB+5V USB_P12USB_P12+ GND NC USB1112 M4A78 USB+5V USB_P7USB_P7+ GND PIN 1 USB+5V USB_P9USB_P9+ GND PIN 1 USB+5V USB_P11USB_P11+ GND PIN 1 M4A78 USB2.0 connectors 請勿將 1394 數據線連接到 USB 插座上,這麼做可能會導致主板的損 壞。 USB 2.
6. 內置音頻信號接收插槽 (4-pin CD) 這些連接插槽用來接收從光盤、電視調頻器或 MPEG 卡等設備所傳送出來的 音源信號。 Left Audio Channel GND GND Right Audio Channel CD M4A78 M4A78 Internal audio connector 7.
8. 數字音頻連接排針 (4-1 pin SPDIF_OUT) SPDIFOUT GND M4A78 +5V 這組排針是用來連接 S/PDIF 數字音頻模塊。 SPDIF_OUT M4A78 Digital audio connector 請確認播放聲音的音頻設備為 Realtek High Definition Audio(此名稱可能 因操作系統不同而有差異)。請至【開始】>【控制面板】>【聲音與音頻 設備】>【聲音】來進行設置。 S/PDIF 模塊需另行購買。 9. 中央處理器 / 機箱 /電源 風扇電源插槽 (4 pin CPU_FAN、3-pin CHA_FAN、 3-pin PWR_FAN) 您可以將 350mA~740mA (最大 8.88 瓦) 或者一個合計為 1A~2.22A (最大 26.
1.11 軟件支持 1.11.1 安裝操作系統 本主板完全適用於 Windows® XP/Vista 操作系統(OS,Operating System)。永 遠使用最新版本的操作系統並且不定時地昇級,是讓硬件配備得到最佳工作效率的有 效方法。 • 由於主板和外圍硬件設備的選項設置繁多,本章僅就軟件的安裝程序 供您參考。您也可以參閱您使用的操作系統說明文件以取得更詳盡的 信息。 • 在安裝驅動程序之前,請先確認您已經安裝 Windows® XP Service Pack 3 / Windows® Vista Service Pack 1 或更新版本的操作系統,來獲得更 好的性能與系統穩定。 1.11.2 驅動程序與應用程序光盤信息 隨貨附贈的驅動程序與應用程序光盤包括了數個有用的軟件和應用程序,將它們 安裝到系統中可以強化主板的機能。 驅動程序與應用程序光盤的內容若有更新,恕不另行通知。請訪問華碩網 站(www.asus.com.
第二章 BIOS 信息 2.1 管理、更新您的 BIOS 程序 建議您先將主板原始的 BIOS 程序備份到一片啟動盤中,以備您往後需要再 度安裝原始的 BIOS 程序。使用 AFUDOS 或華碩在線升級程序或 AFUDOS 工具程序 來拷貝主板原始的 BIOS 程序。 2.1.1 華碩在線升級程序(ASUS Update Utility) 華碩在線升級程序是一套可以讓您在 Windows 操作系統下,用來管理、保存與更 新主板 BIOS 文件的應用程序。您可以使用華碩在線升級程序來運行以下的功能: •在使用華碩在線升級程序之前,請先確認您已經通過內部網絡對外連 接,或者通過互聯網服務供應商(ISP)所提供的連接方式連接到互聯 網。 •主板附贈的驅動程序及應用程序光盤中包含此應用程序。 安裝華碩在線升級程序 請依照以下的步驟安裝華碩在線升級程序: 1. 將驅動程序和應用程序光盤放入光驅,會出現“驅動程序”菜單。 2. 點擊【應用程序】標籤,然後點擊【安裝華碩在線升級程序】。 3.
使用 BIOS 文件升級 BIOS 程序 a. 選擇【Update BIOS from a file】,然後按下【Next】繼續。 b. 在【打開】的窗口中選擇 BIOS 文件的所在位置,然後點擊【打開】。 3. 最後再依照屏幕畫面的指示來完成 BIOS 更新的程序。 2.1.2 使用華碩 EZ Flash 2 升級 BIOS 程序 華碩 EZ Flash 2 程序讓您能輕鬆地升級 BIOS 程序,可以不必再通過啟動盤的冗 長程序或是到 DOS 模式下運行。 從華碩網站上(www.asus.com.cn)下載最新的 BIOS 文件。 請依據以下步驟使用 EZ Flash 2 升級 BIOS: 1. 將保存有 BIOS 文件的 USB 閃存盤插入 USB 接口。 您可以使用下列兩種方式 來運行 EZ Flash 2: a. 在 POST 開機自檢時,按下 + 鍵,便會顯示如下所示的畫面。 ASUSTek EZ Flash 2 BIOS ROM Utility V3.
2.1.3 使用 CrashFree BIOS 3 程序恢復 BIOS 程序 華碩最新自行研發的 CrashFree BIOS 3 工具程序,讓您在當 BIOS 程序和數據被 病毒入侵或毀壞時,可以輕鬆地從驅動程序與應用程序光盤中,或是從含有最新或原 始的 BIOS 文件的軟盤或 USB 閃存盤中恢復 BIOS 程序的數據。 • 在您使用此應用程序前,請先準備好內含主板 BIOS 的驅動程序與應用 程序光盤,或是 USB 閃存盤,作為恢復 BIOS 的用途。 • 請務必將 SATA 數据線連接至 SATA1 / 2 / 3 / 5 / 6 接頭。否則,該 程序無法使用。 恢復 BIOS 程序: 請依照下列步驟恢復 BIOS 程序: 1. 啟動系統。 2. 將存有 BIOS 文件的驅動程序與應用程序光盤或 USB 閃存盤放入光驅或 USB 插 槽中。 3. 接著工具程序便會顯示如下所示的信息,並自動檢查光盤或 USB 閃存盤中是否 存有 BIOS 文件。 Bad BIOS checksum. Starting BIOS recovery... Checking for CD-ROM...
2.2 BIOS 程序設置 本主板擁有一片可編程的 Serial Peripheral Interface(SPI)芯片,您可以依 照“2.
2.2.1 BIOS 程序菜單介紹 功能表列 菜單項目 Main Advanced Primary IDE Master Primary IDE Slave SATA1 SATA2 SATA3 ESATA SATA5 SATA6 SATA Configuration 在線操作說明 BIOS SETUP UTILITY Boot Tools Exit Power System Time System Date 設置值 [19:34:30] [Wed 08/27/2008] :[Not :[Not :[Not :[Not :[Not :[Not :[Not :[Not :[Not Detected] Detected] Detected] Detected] Detected] Detected] Detected] Detected] Detected] System Information Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system Time.
2.2.3 操作功能鍵說明 在菜單畫面的右下方為操作功能鍵說明,請參照功能鍵說明來選擇及改變各項功 能。 操作功能鍵將因功能頁面的不同而有所差異。 2.2.4 菜單項目 在功能表列選定選項時,被選擇的功能將會反白。 點擊菜單中的其他項目(例如:Advanced、Power、Tool 、Boot 與 Exit)也會 出現該項目不同的選項。 2.2.5 子菜單 在菜單畫面中,若功能選項前面有一個小三角形標記,代表此為子菜單,您可利 用方向鍵來選擇,並按下 <Enter> 鍵來進入子菜單。 2.2.6 設置值 此區域顯示菜單項目的設置值。這些項目中,有的功能選項僅為告知用戶目前運 行狀態,並無法更改,此類項目就會以淡灰色顯示。而可更改的項目,當您使用方向 鍵移動項目時,被選擇的項目以反白顯示。 設置值被選擇後以反白顯示。要改變設置值請選擇此項目,並按下 <Enter> 鍵 以顯示設置值列表。請參考“2.2.8 設置窗口”的說明。 2.2.7 在線操作說明 在菜單畫面的右上方為目前所選擇的作用選項的功能說明,此說明會依選項的不 同而 自動變更。 2.2.
2.3 主菜單(Main) 當您進入 BIOS 設置程序時,首先出現的第一個畫面即為主菜單,內容如下圖。 請參閱“2.2.
Block (Multi-Sector Transfer) M [Auto] 開啟或關閉數據同時傳送多個磁區功能。當您設為 [Auto] 時,數據傳送便可同 時傳送至多個磁區,若設為 [Disabled],數據傳送便只能一次傳送一個磁區。設置值 有:[Disabled] [Auto] PIO Mode [Auto] 選擇 PIO 模式。設置值有:[Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] 選擇 DMA 模式。設置值有:[Auto] SMART Monitoring [Auto] 開啟或關閉自動偵測、分析、報告技術(SMART Monitoring、Analysis 與 Reporting Technology)。設置值有:[Auto] [Disabled] [Enabled] 32Bit Data Transfer [Enabled] 開啟或關閉 32 位數據傳輸功能。設置值有:[Disabled] [Enabled] 2.3.
2.3.5 SATA 設置(SATA Configuration) 本菜單可讓您設置存儲設備。選擇您想要的項目並按 <Enter> 鍵來進行各項設 備的設置。 OnChip SATA Channel [Enabled] 本項目允許您開啟或關閉內置 SATA 通道。設置值有:[Enabled] [Disabled] OnChip SATA Type [SATA] 只有將 OnChip SATA Channel 項目設為 [Enabled] 時,此項目才會出現。本項目 允許您設置內置 SATA 類型。設置值有:[SATA] [RAID] [AHCI] 在 BIOS 中,若將 SATA 設為 [AHCI] 時,僅可偵測到 SATA 1-3 接口。 請安裝 AHCI 驅動程序,以偵測到 SATA 1 / 2 / 3 / 5 / 6 接口,並可在 AHCI 模式中使用 SATA1 / 2 / 3 / 5 / 6 接口。 2.3.
2.4.
Memory Clock Mode [Auto] 本項目可讓您設置內存頻率模式。設置值有:[Auto] [Manual] 只有在 Memory clock mode 項目設為 [Manual] 時以下項目才會出現。 Memclock Value [200 MHz] 本項目可讓您設置內存頻率值。設置值有:[200 MHz] [266 MHz] [333 MHz] [400 MHz] DRAM Timing Mode [Auto] 項目可讓您設置 DRAM 時序模式。設置值有:[Auto] [DCT 0] 只有在 DRAM Timing Mode 項目設為 [DCT 0] 時以下項目才會出現。 CAS# Latency [ Auto] 本項目可讓您設置 CAS# latency。設置值有:[Auto] [3 CLK] [4 CLK] [5 CLK] [6 CLK] [7 CLK DH_Only] TRCD [ Auto] 本項目可讓您設置 TRCD。設置值有:[3 CLK] [4 CLK] [5 CLK] [6 CLK] [Auto] TRP [ Auto] 本項目可讓您設置 TRP。設置值有:[3 CLK
tWRRD [ Auto] 本項目允許您設置當訪問不同 DRAM 時,寫入到讀取的延遲。設置值有: [Auto] [0 CLK] [1 CLK] [2 CLK] [3 CLK] tWTR [ Auto] 本項目允許您設置當訪問同一個 DRAM 有:[1 CLK] [2 CLK] [3 CLK] [Auto] tWRWR [ Auto] 時,寫入到讀取的延遲。設置值 本項目允許您設置 Twrwr 時間。設置值有:[Auto] [0 CLK] [1 CLK] [2 CLK] [3 CLK] tRDRD [ Auto] 本項目允許您設置 Trdrd 時間。設置值有:[Auto] [2 CLK] [3 CLK] [4 CLK] [5 CLK] tRFC0/1/2/3[ Auto] 本項目允許您設置 Trfc0/1/2/3 時間。設置值有:[Auto] [75ns] [105ns] [127.5ns] [195ns] [327.5ns] Memory Over Voltage [Auto] 本項目可讓您設置內存超壓。設定值範圍從 1.85000V 到 2.24375V,以 0.
2.4.
2.4.
2.4.6 USB 設備設置(USB Configuration) 本菜單可讓您變更USB設備的各項相關設置。請選擇所需的項目並按下 <Enter> 鍵以顯示設置選項。 在 Module Version 與 USB Devices Enabled 項目中會顯示自動偵測到的 設備。若無連接任何設備,則會顯示 [None]。 USB Functions [Enabled] 本項目用來開啟或關閉 USB 功能。設置值有:[Disabled] [Enabled] USB 2.0 Controller [Enabled] 本項目用來開啟或關閉 USB 2.
2.5 電源管理(Power) 電源管理菜單選項,可讓您變更高級電源管理(APM)與 ACPI 的設置。請選擇 下列選項並按下 <Enter> 鍵來顯示設置選項。 Suspend Mode ACPI 2.0 Features ACPI APIC Support [Auto] [Disabled] [Enabled] Select the ACPI state used for System Suspend. APM Configuration HW Monitor 2.5.
Power On From S5 By PME# [Disabled] 本項目讓您開啟或關閉通過 PME 喚醒電腦。設置值有:[Disabled] [Enabled] Power On From S5 By Ring [Disabled] 本項目讓您開啟或關閉 RI 來生成喚醒事件。設置值有:[Disabled] [Enabled] Power On From S5 By PS/2 KB/MS [Disabled] 本項目讓您開啟或關閉 PS/2 鍵盤或鼠標喚醒功能。設置值有:[Disabled] [Enabled] Power On From S5 By RTC Alarm [Disabled] 本項目讓您開啟或關閉 RTC 喚醒功能。若設為 [Enabled],RTC Alarm Date, RTC Alarm Hour, RTC Alarm Minute 與 RTC Alarm Second 項目會出現設置值。設置值 有:[Disabled] [Enabled] 2.5.
2.6 啟動菜單(Boot) 本菜單可讓您改變系統啟動設備與相關功能。請選擇所需的項目並按下 <Enter> 鍵以顯示子菜單項目 Main Advanced Power BIOS SETUP UTILITY Boot Tools Exit Specifies the Boot Device Priority sequence. Boot Settings Boot Device Priority A virtual floppy disk drive (Floppy Drive B:) may appear when you set the CD-ROM drive as the first boot device. Boot Settings Configuration Security Enter F1 F10 ESC Select Screen Select Item Go to Sub Screen General Help Save and Exit Exit v02.61 (C)Copyright 1985-2008, American Megatrends, Inc.
Wait for ‘F1’ If Error [Enabled] 當您將本項目設為 [Enabled],那麼系統在開機過程出現錯誤信息時,將會等待您 按下 <F1> 鍵確認才會繼續進行開機程序。設置值有;[Disabled] [Enabled] Hit ‘DEL’ Message Display [Enabled] 當您將本項目設為 [Enabled] 時,系統在開機過程中會出現“Press DEL to run Setup”信息。設置值有:[Disabled] [Enabled] 2.6.3 安全性菜單(Security) 本菜單可讓您改變系統安全設置。請選擇下列選項並按下 鍵來顯示設置 選項。 Change Supervisor Password(變更系統管理員密碼) 本項目是用於變更系統管理員密碼。本項目的運行狀態會於畫面上方以淡灰色顯 示。默認值為 Not Installed。當您設置密碼後,則此項目會顯示 Installed。 請依照以下步驟設置系統管理員密碼(Supervisor Password): 1.
Change User Password(變更用戶密碼) 本項目是用於變更用戶密碼,運行狀態會於畫面上方以淡灰色顯示,默認值為 Not Installed。當您設置密碼後,則此項目會顯示 [Installed]。 請依照以下步驟設置用戶密碼(User Password): 1. 選擇【Change User Password】項目並按下 <Enter>。 2. 在“Enter Password”窗口出現時,請輸入欲設置的密碼,可以是六個字符內 的英文、數字與符號。輸入完成按下 <Enter>。 3.
2.7 工具菜單(Tools) 本工具菜單可以讓您針對特別功能進行設置。請選擇菜單中的選項並按下 鍵來顯示子菜單。 Main Advanced Power BIOS SETUP UTILITY Boot Tools Exit ASUS EZ Flash 2 Express Gate Enter OS Timer Reset User Date [Auto] [10 Seconds] [No] Press ENTER to run the utility to select and update BIOS. This utility doesn't support : 1.NTFS format AI NET2 Select Screen Select Item +Change Field Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit v02.61 (C)Copyright 1985-2007, American Megatrends, Inc. 2.7.
2.8 退出 BIOS 程序(Exit) 本菜單可讓您讀取 BIOS 程序出廠默認值與退出 BIOS 程序,並可保存和取消對 BIOS 項目的更改。 Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Load Setup Defaults Exit system setup after saving the changes. F10 key can be used for this operation.