Carte mère M4A78LT-M
F5232 Première édition V1 Décembre 2009 Copyright © 2009 ASUSTeK COMPUTER INC. Tous droits réservés. Aucun extrait de ce manuel, incluant les produits et logiciels qui y sont décrits, ne peut être reproduit, transmis, transcrit, stocké dans un système de restitution, ou traduit dans quelque langue que ce soit sous quelque forme ou quelque moyen que ce soit, à l’exception de la documentation conservée par l’acheteur dans un but de sauvegarde, sans la permission écrite expresse de ASUSTeK COMPUTER INC.
Table des matières Notes .......................................................................................................... vi Informations sur la sécurité....................................................................... vii À propos de ce manuel.............................................................................. vii Résumé des spécifications de la M4A78LT-M........................................... ix Chapitre 1 : Introduction au produit 1.1 Bienvenue !.........................
Table des matières 1.11 Support logiciel........................................................................... 1-30 1.11.1 1.11.2 Chapitre 2 : 2.1 Informations sur le DVD de support............................... 1-30 Le BIOS Gérer et mettre à jour votre BIOS................................................ 2-1 2.1.1 Utilitaire ASUS Update..................................................... 2-1 2.1.3 Utilitaire ASUS CrashFree BIOS 3................................... 2-3 2.1.2 2.
Table des matières 2.5.3 ACPI APIC Support........................................................ 2-16 2.5.5 HW Monitor Configuration.............................................. 2-16 2.5.4 2.6 2.5.6 2.6.1 Boot Device Priority....................................................... 2-18 2.6.3 Security.......................................................................... 2-19 Boot Settings Configuration........................................... 2-18 Menu Tools (Outils).......................
Notes Rapport de la Commission Fédérale des Communications Ce dispositif est conforme à l’alinéa 15 des règles établies par la FCC. L'opération est sujette aux 2 conditions suivantes: • • Ce dispositif ne peut causer d'interférence nuisible, et Ce dispositif se doit d'accepter toute interférence reçue, incluant toute interférence pouvant causer des résultats indésirables.
Informations sur la sécurité Sécurité électrique • • • • • • Pour éviter tout risque de choc électrique, débranchez le câble d’alimentation de la prise de courant avant de toucher au système. Lorsque vous ajoutez ou enlevez des composants, vérifiez que les câbles d’alimentation sont débranchés avant de relier les câbles de signal. Si possible, déconnectez tous les câbles d’alimentation du système avant d’ajouter un périphérique.
Conventions utilisées dans ce guide Pour être certains que vous effectuiez certaines tâches correctement, veuillez prendre notes des symboles suivants. DANGER/AVERTISSEMENT : Ces informations vous permettront d’éviter de vous blesser lors de la réalisation d’une tâche. ATTENTION : Ces informations vous permettront d’éviter d’endommager les composants lors de la réalisation d’une tâche. IMPORTANT : Instructions que vous DEVEZ suivre pour mener à bien une tâche.
Résumé des spécifications de la M4A78LT-M CPU Chipset Bus système Mémoire Graphiques Slots d’extension Socket AM3 pour processeurs AMD Phenom™ II / Athlon™ II / Sempron™ Séries 100 Support des CPU utilisant une finesse de gravure de 45nm Technologie AMD Cool ‘n’ Quiet™ 2.0 (selon le type de CPU) Support des CPU alimentés jusqu’à 125W AMD 760G (780L) / SB710 Interface HyperTransport™ 3.
Résumé des spécifications de la M4A78LT-M Stockage/RAID 1 x connecteur UltraDMA 133/100 6 x connecteurs Serial ATA 3Gb/s avec support RAID 0, RAID 1, RAID 0+1 et JBOD Audio CODEC High Definition Audio VT1708S 8 canaux – Sortie SPDIF sur le panneau d’E/S – Supporte la détection des ports audio, la fonction Anti-pop et le Multi-streaming USB Réseau Supporte jusqu’à 12 ports USB 2.0/1.
Résumé des spécifications de la M4A78LT-M Connecteurs internes 3 x connecteurs USB 2.0/1.1 supportant 6 ports USB 2.0/1.1 supplémentaires. 1 x connecteur IDE 1 x connecteur LPT 1 x connecteur COM 6 x connecteurs SATA 1 x connecteur pour port audio en façade 1 x connecteur système 1 x connecteur de sortie S/PDIF 1x connecteur de ventilation CPU/Châssis Connecteur d’alimentation EATX 24 broches Connecteur d’alimentation ATX 12V 4 broches BIOS 8Mo de ROM Flash, BIOS AMI, PnP, DMI2.0, WfM2.0, ACPI2.
Chapitre 1 1.1 Bienvenue ! Merci d’avoir acheté une carte mère ASUS® M4A78LT-M ! La carte mère offre les technologies les plus récentes associées à des fonctionnalités nouvelles qui en font un nouveau digne représentant de la qualité des cartes mères ASUS ! Avant de commencer à installer la carte mère, vérifiez le contenu de la boîte grâce à la liste ci-dessous. 1.2 Contenu de la boîte Vérifiez que la boîte de la carte mère contienne bien les éléments suivants.
Support de l’interface HyperTransport™ 3.0 La technologie HyperTransport™ 3.0 offre une bande passante 2.6 fois plus élevée que l’interface HT1.0 pour améliore de manière radicale l’efficacité du système pour un environnement de travail plus fluide et plus rapide. Techologie AMD® Hybrid CrossFireX La technologie Hybrid CrossFireX est une technologie multi-GPU unique combinant le chipset graphique embarqué et le GPU d’une carte graphique pour accroître les performances 3D.
1.3.2 Fonctionnalités innovantes ASUS Express Gate - Accès Internet en quelques secondes Permettant d’être en ligne seulement quelques secondes après le démarrage, Express Gate est le portail d’accès instantané aux loisirs idéal sans avoir à accéder au système d’exploitation. • ASUS Express Gate peut être installé sur des disques durs SATA, USB et Flash disposant d’au moins 1.2Go d’espace disque libre.
ASUS Q-Fan La technologie ASUS Q-Fan ajuste la vitesse du ventilateur en fonction de la charge du système pour assurer un fonctionnement silencieux, frais et efficace. Green ASUS Cette carte mère et son emballage sont conformes à la norme Européenne RoHS (Restriction on the use of Hazardous Substances).
1.4 Avant de commencer Suivez les précautions ci-dessous avant d’installer la carte mère ou d’en modifier les paramètres. • Débranchez le câble d’alimentation de la prise murale avant de toucher les composants. • Utilisez un bracelet antistatique ou touchez un objet métallique relié au sol (comme l’alimentation) pour vous décharger de toute électricité statique avant de toucher aux composants. • Tenez les composants par les coins pour éviter de toucher les circuits imprimés.
1.5 Vue générale de la carte mère 1.5.1 Orientation de montage 1.5.2 Pas de vis Lorsque vous installez la carte mère, vérifiez que vous la montez dans le châssis dans le bon sens. Le côté qui porte les connecteurs externes doit être à l’arrière du châssis, comme indiqué sur l’image ci-dessous. Placez huit (8) vis dans les trous indiqués par des cercles pour fixer la carte mère au châssis. Ne vissez pas trop fort ! Vous risqueriez d’endommager la carte mère.
1.5.3 Diagramme de la carte mère 1 2 3 2 4 5 24.4cm(9.6in) KB_USB56 COM1 CPU_FAN ATX12V Super I/O LPT DDR3 DIMM_B1 (64bit, 240-pin module) 6 24.4cm(9.
1.6 Central Processing Unit (CPU) La carte mère est livrée avec un socket conçu pour l’installation d’un processeur AMD® Phenom™ II / Athlon™ II / Sempron™ Séries 100. Le socket AM3 possède un brochage différent des sockets pour processeurs AM2+/AM2. Assurez-vous d’utiliser un processeur conçu pour le socket AM3. 1.6.1 Installer le CPU Pour installer un CPU: 1. Localisez le socket du CPU de la carte mère. M4A78LT-M Socket du CPU de la M4A78LT-M M4A78LT-M CPU socket AM3 2.
5. 6. 7. Lorsque le CPU est en place, abaissez le levier pour sécurisez le CPU. Un léger cliquetis se fait entendre indiquant que le CPU est bien verrouillé. Installez un ensemble dissipateur-ventilateur pour CPU en suivant les instructions contenues dans la boîte du système de refroidissement. Connectez le câble du ventilateur du CPU au connecteur CPU_FAN de la carte mère.
La boîte de votre processeur doit contenir les instructions d’installation du CPU, et de l’ensemble dissipateur-ventilateur. Si les instructions contenues dans cette section ne correspondent pas la documentation du CPU, suivez cette dernière. 2. Attachez l’un des crochets de rétention à la base du module de rétention. 1 2 3 3. 4 5 Alignez l’autre crochet de rétention (situé à côté du système de verrouillage) à la base du module de rétention.
1.7 Mémoire système 1.7.1 Vue générale DIMM_A1 DIMM_B1 DIMM_A2 DIMM_B2 La carte mère est équipée de deux sockets Dual Inline Memory Modules (DIMM) Double Data Rate 3 (DDR3). L’illustration ci-dessous indique l’emplacement des sockets pour modules mémoire DR3. Canal Sockets Canal A DIMM_A1 et DIMM_A2 Canal B DIMM_B1 et DIMM_B2 M4A78LT-M Sockets DIMM DDR3 de laDDR3 M4A78LT-M M4A78LT-M 240-pin DIMM sockets 1.7.
Liste des fabricants de mémoire agréés de la M4A78LT-M DDR3-1866(O.C)MHz Support DIMM Fabricant N° de pièce Taille SS/ DS Marque N° de puce / Composants CL Kingston KHX14900D3K3/3GX(XMP) 3072MB(kit of 3) SS N/A Heat-Sink Package 9-9-9-27 A* B* • • C* DDR3-1800(O.C.
DDR3-1333MHz Fabricant N° de pièce Taille SS/ DS Marque N° de puce / Composants CL A-Data AD31333001GOU 1024MB SS A-Data AD30908C8D-151C E0906 A-Data AD31333002GOU 2048MB DS A-Data Apacer 78.01GC6.9L0 1024MB SS Apacer Apacer 78.A1GC6.
DDR3-1333MHz (suite) 1-14 Fabricant N° de pièce Taille SS/ DS Marque N° de puce / Composants CL GEIL DDR3-1333 CL9-9-9-24 6144MB(Kit of 3) DS N/A Heat-Sink Package Kingston KVR1333D3N9/1G 1024MB SS elpida Kingston KVR1333D3N9/2G 2048MB DS Micron MT8JTF12864AY-1G4D1 1024MB Micron MT16JTF25664AY-1G1D1 Micron Support DIMM A* B* C* 9 • • • J1108BABG-DJ-E 9 • • • elpida J1108BABG-DJ-E 9 • • • SS Micron 8LD22D9JNM N/A • • • 2048MB DS Micron 8LD22 D9JNM N/
DDR3-1066MHz Fabricant N° de pièce Taille SS/ DS Marque N° de puce / Composants CL Elpida EBJ51UD8BAFA-AC-E 512MB SS elpida J5308BASE-AC-E Elpida EBJ51UD8BAFA-AE-E 512MB SS elpida G.SKILL F3-8500CL6D-2GBHK 1024MB SS Kingston KVR1066D3N7/1G 1024MB Kingston KVR1066D3N7/1G Kingston Support DIMM A* B* C* N/A • • • J5308BASE-AC-E N/A • • • G.
1.7.3 Installer un module mémoire Débranchez l’alimentation avant d’ajouter ou de retirer des modules mémoire ou tout autre composant système. Ne pas le faire risquerait d’endommager la carte mère et les composants. 1. 2. 2 Déverrouillez un socket pour module mémoire en pressant les clips de rétention vers l’extérieur. Encoche du module mémoire Alignez un module mémoire sur le socket de sorte que l’encoche sur le module corresponde à l’ergot sur le socket.
1.8 Slots d’extension Plus tard, vous pourrez avoir besoin d’installer des cartes d’extension. La section suivante décrit les slots et les cartes d’extension supportées. Assurez-vous de bien débrancher le câble d’alimentation avant d’ajouter ou de retirer des cartes d’extension. Ne pas le faire risquerait de vous blesser et d’endommager les composants de la carte mère. 1.8.1 Installer une carte d’extension Pour installer une carte d’extension: 1. 2. 3. 4. 5. 6.
1.9 Jumper Jumper d’effacement de la mémoire RTC (3-pin CLRTC) Ce jumper vous permet d’effacer la mémoire RTC (Real Time Clock) du CMOS. Vous pouvez effacer de la mémoire CMOS, la date, l’heure et paramètres du système en effaçant les données de la mémoire RTC CMOS . La pile bouton intégrée alimente les données de la mémoire dans le CMOS, incluant les paramètres système tels que les mots de passe.
1.10 Connecteurs 1.10.1 Connecteurs arrières 1 2 3 15 14 13 4 12 5 6 7 8 11 10 9 1. Port clavier PS/2. Ce port accueille une souris ou un clavier PS/2. 2. Port de sortie S/PDIF optique. Ce port sert à être relié à un périphérique audio externe via un câble optique S/PDIF. 3. Port VGA. Ce port 15 broches est destiné à un périphérique VGA. 4. Port LAN (RJ-45). Ce port permet une connexion Gigabit à un réseau local LAN (Local Area Network) via un hub réseau.
Configurations audio 2, 4, 6 et 8 canaux Port Bleu clair Casque 2 canaux 4 canaux 6 canaux 8 canaux Line In Line In Line In Line In Vert Line Out Front Speaker Out Front Speaker Out Front Speaker Out Rose Mic In Mic In Mic In Mic In Orange – – Center/Subwoofer Center/Subwoofer Noir – Rear Speaker Out Rear Speaker Ou Rear Speaker Out Gris – – – Side Speaker Out Assurez-vous que le périphérique de lecture audio est bien VIA High Definition Audio (le nom peut différer selon le
• Lecture de disques HD DVD et Blu-Ray Pour une meilleure qualité de lecture, assurez-vous que votre système satisfasse aux critères ci-dessous. Configuration recommandée CPU AMD® Phenom II x3 720 Mémoire DDR3 1333 (1GB or higher) BIOS Taille tampon - 256Mo ou plus Format de fichier Résolution optimale Windows XP Windows Vista / 7 Clips non protégés 1920 x 1080p 1920 x 1080p HD-DVD 1920 x 1080p 1280 x 1080p Blu-Ray 1280 x 1080p 1280 x 1080p • Formats vidéos pris en charge : VC-1, H.
1.10.2 1. Connecteurs internes Connecteurs de ventilation CPU et châssis (4-pin CPU_FAN and 3-pin CHA_FAN) Connectez les câbles des ventilateurs à ces connecteurs sur la carte mère, en vous assurant que le fil noir de chaque câble corresponde à la broche de terre de chaque connecteur. N’oubliez pas de connecter le câble du ventilateur pour CPU au connecteur CPU_Fan de la carte mère. Un flux d’air insuffisant dan le châssis peut endommager les composants de la carte mère.
2. Connecteurs d’alimentation ATX (24-pin EATXPWR, 4-pin ATX12V) Ces connecteurs sont destinés aux prises d’alimentation ATX. Les prises d’alimentation sont conçues pour n’être insérées que dans un seul sens dans ces connecteurs. Trouvez le bon sens et appuyez fermement jusqu’à ce que la prise soit bien en place.
Connecteur IDE (40-1 pin PRI_IDE) Ce connecteur est destiné à un câble Ultra DMA 133/100. Le câble Ultra DMA 133/100 possède trois connecteurs: un bleu, un noir, et un gris. Connectez l’interface bleue au connecteur IDE primaire de la carte mère, puis sélectionner un des modes ci-dessous pour configurer vos lecteurs IDE. PRI_IDE PIN1 3. M4A78LT-M Note : Orientez les rouges NOTE:Orient themarques red markings du du lecteur disquettes oncâble the IDE ribbonde cable to PIN 1.
Connecteurs Serial ATA (7-pin SATA1, SATA2, SATA3, SATA4, SATA5, SATA6) Ces connecteurs sont destinés à des câbles Serial ATA pour la connexion de disques durs et de lecteurs optiques Serial ATA 3Gb/s. La norme Serial ATA 3Gb/s est rétrocompatible avec la spécification Serial ATA 1.5 Gb/s. Le taux de transfert de données du SATA 3Gb/s est plus rapide que celui du standard PATA qui fonctionne à 133 MB/s (Ultra DMA133).
5. Connecteur panneau système (20-8 pin PANEL) Ce connecteur supporte plusieurs fonctions intégrées au châssis. +5V Ground Ground Speaker SPEAKER PLED- PLED+ PLED PANEL M4A78LT-M IDE_LED PWRSW Reset Ground IDE_LED+ IDE_LED- PWR Ground PIN 1 RESET * Requires an ATX power supply M4A78LT-M System panel connector Connecteur système de la M4A78LT-M • • • • • 1-26 LED d’alimentation système (2-pin PWRLED) Ce connecteur 2 broches est dédié à la LED d’alimentation système.
Connecteurs USB (10-1 pin USB78, USB910, USB1112) USB78 USB+5V USB_P12USB_P12+ GND NC USB910 USB1112 PIN 1 PIN 1 USB+5V USB_P9USB_P9+ GND USB+5V USB_P7USB_P7+ GND PIN 1 M4A78LT-M USB+5V USB_P11USB_P11+ GND USB+5V USB_P10USB_P10+ GND NC Ces connecteurs sont dédiés à des ports USB2.0. Connectez le câble du module USB à l’un de ces connecteurs, puis installez le module dans un slot à l’arrière du châssis. Ces connecteurs sont conformes au standard USB 2.
Connecteur audio numérique (4-1 pin SPDIF_OUT) SPDIFOUT GND Ce connecteur est destiné à un/des port/s additionnel Sony/Philips Digital Interface (S/PDIF). +5V 8. M4A78LT-M SPDIF_OUT M4A78LT-M Digital audio Connecteur audio numérique de laconnector M4A78LT-M Le module S/PDIF est vendu séparément. Assurez-vous que le périphérique de lecture audio est bien VIA High Definition Audio (le nom peut différer selon les systèmes d’exploitation).
Connecteur pour port audio en façade (10-1 pin AAFP) NC AGND NC NC SENSE2_RETUR Ce connecteur est dédié à un module E/S audio pour panneau avant et supportant les standards AC ‘97 audio et HD Audio. GND PRESENCE# SENSE1_RETUR 9.
1.11 Support logiciel 1.11.1 Installer un système d’exploitation Cette carte mère supporte Windows® XP/Vista/7. Installez toujours la dernière version des OS et les mises à jour correspondantes pour maximiser les caractéristiques de votre matériel. • Les réglages de la carte mère et les options matérielles peuvent varier. Utilisez les procédures décrites ici en guise d’exemple. Reportez-vous à la documentation livrée avec votre OS pour des informations détaillées.
Chapitre 2 Le BIOS 2.1 Gérer et mettre à jour votre BIOS Sauvegardez une copie du BIOS original de la carte mère sur une disque de stockage au cas où vous deviez restaurer le BIOS. Copiez le BIOS original en utilisant ASUS Update. 2.1.1 Utilitaire ASUS Update ASUS Update est un utilitaire qui vous permet de gérer, sauvegarder et mettre à jour le BIOS de la carte mère sous un environnement Windows®. • ASUS Update nécessite une connexion Internet via un réseau ou via un fournisseur d’accès.
Mise à jour du BIOS grâce à un fichier BIOS a. Choisissez Update BIOS from a file dans le menu déroulant puis cliquez sur Next. b. Localisez le fichier BIOS puis cliquez sur Sauvegarder. 3. Suivez les instructions à l’écran pour terminer le processus de mise à jour. 2.1.2 Utilitaire ASUS EZ Flash 2 ASUS EZ Flash 2 vous permet de mettre à jour votre BIOS sans avoir besoin de démarrer à partir d’une disquette de démarrage ou d’utiliser un utilitaire sous le système d’exploitation.
2.1.3 Utilitaire ASUS CrashFree BIOS 3 ASUS CrashFree BIOS 3 est un outil de récupération automatique qui permet de récupérer le fichier du BIOS lorsqu’il est défectueux ou qu’il est corrompu lors d’une mise à jour. Vous pouvez mettre à jour un BIOS corrompu en utilisant le DVD de support de la carte mère ou un périphérique de stockage amovible qui contient le BIOS à jour. • Avant d’utiliser cet utilitaire, renommez le fichier BIOS MA78LTM.ROM.
2.2 Programme de configuration du BIOS Utilisez le programme de configuration du BIOS lorsque vous installez la carte mère, lorsque vous voulez reconfigurer le système, où lorsque vous y êtes invité par le message “Run Setup”. Cette section vous explique comment configurer votre système avec cet utilitaire. Accéder au BIOS au démarrage Pour accéder au BIOS au démarrage du système : • Appuyez sur lors du POST (Power-On Self Test). Si vous n’appuyez pas sur , le POST continue ses tests.
2.2.1 Ecran de menu du BIOS Eléments du menu Main Barre de menu Advanced Power System Time System Date Primary IDE Master Primary IDE Slave SATA1 SATA2 SATA3 SATA4 SATA5 SATA6 SATA Configuration Champs de configuration BIOS SETUP UTILITY Boot Tools Exit [19:34:30] [Fri 09/04/2009] :[Not :[Not :[Not :[Not :[Not :[Not :[Not :[Not System Information Aide générale Detected] Detected] Detected] Detected] Detected] Detected] Detected] Detected] Use [ENTER], [TAB] or [SHIFT-TAB] to select a field.
2.2.3 Touches de navigation En bas à droite d’un écran de menu se trouvent les touches de navigation. Utilisez-les pour naviguer dans ce menu. Ces touches peuvent varier d’un menu à l’autre. 2.2.4 Eléments de menu L’élément surligné dans la barre de menu affiche les éléments spécifiques à ce menu. Par exemple, sélectionner Main affiche les éléments du menu principal. Les autres éléments (Advanced, Power, Boot, Tool et Exit) de la barre de menu ont leurs propres menus respectifs. 2.2.
2.3 Menu Main (Principal) Lorsque vous entrez dans le programme de configuration du BIOS, l’écran du menu principal apparaît, vous donnant une vue d’ensemble sur les informations de base du système. Référez-vous à la section “2.2.1 “Ecran de menu du BIOS” pour plus d’informations sur l’écran de menus et sur la façon d’y naviguer.
données vers et depuis le périphérique se feront par plusieurs secteurs à la fois, si le périphérique supporte la fonction de transfert multi-secteurs. Sur [Disabled], les transferts de données vers et depuis le périphérique se feront secteur par secteur. Options de configuration : [Disabled] [Auto] PIO Mode [Auto] Sélectionne le mode PIO. Options de configuration : [Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] Sélectionne le mode DMA.
2.4 Menu Advanced (Avancé) Les éléments du menu Advanced vous permettent de modifier les paramètres du CPU et d’autres composants système. Prenez garde en changeant les paramètres du menu Advanced. Des valeurs incorrectes risquent d’entraîner un mauvais fonctionnement du système. Main Advanced Power BIOS SETUP UTILITY Boot Tools Exit JumperFree Configuration CPU Configuration Chipset Onboard Devices Configuration PCIPnP USB Configuration Adjust System Frequency/Voltage etc.
GPU OverClocking [Auto] Défini le profil d’overclocking du GPU. Options de configuration : [Auto] [Manual] L’élément suivant apparaît uniquement quand GPU Overclocking est défini sur [Manual]. GPU Engine Clock [350] Défini la fréquence du GPU. Choisissez une valeur comprise entre 150 et 1000. PCIE Overclocking [Auto] Défini le profil d’overclocking du bus PCIE. Options de configuration : [Auto] [Manual] L’élément suivant apparaît uniquement quand PCIE Overclocking est défini sur [Manual].
HT Over Voltage [Auto] Permet de sélectionner la valeur de survoltage de l’interface HyperTransport. Les valeurs varient de 1.20000V à 1.38000V par incréments de 0.01500V. Utilisez les touches <+>/<-> de votre clavier pour ajuster la valeur. Options de configuration : [Auto] [Max. = 1.38000V] [Min. = 1.20000V] Memory Clock Mode [Auto] Options de configuration : [Auto] [Manual] L’élément suivant apparaît uniquement quand Memory Clock Mode est réglé sur [Manual].
2.4.2 CPU Configuration Les éléments de ce menu affichent les informations CPU auto-détectées par le BIOS. Microcode Updation [Enabled] Vous permet d’activer ou de désactiver la mise à jour du microcode. Options de configuration : [Disabled] [Enabled] Secure Virtual Machine Mode [Disabled] Active/désactive le mode Secure Virtual Machine (SVM). Options de configuration : [Disabled] [Enabled] Cool’n’Quiet [Enabled] Active/désactive AMD Cool ‘n’ Quiet.
Power Down Enable [Disabled] Options de configuration : [Disabled] [Enabled] ECC Configuration ECC Mode [Disabled] Détermine le niveau de protection ECC permet aux composants de rapporter et corriger les erreurs mémoire automatiquement. Options de configuration : [Disabled] [Basic] [Good] [Super] [Max] [User] Internal Graphics Primary Video Controller [GFX0-GPP-IGFX-PCI] Détermine le contrôleur vidéo primaire.
2.4.4 Onboard Devices Configuration Serial Port1 Address [3F8/IRQ4] Sélectionne l’adresse de base du port série 1. Options de configuration : [Disabled] [3F8/IRQ4][2F8/IRQ3] [3E8/IRQ4] [2E8/IRQ3] Parallel Port Address [378] Sélectionne l’adresse de base du port parallèle. Options de configuration : [Disabled] [378] [278] [3BC] Parallel Port Mode [Normal] Sélectionne le mode du port parallèle.
2.4.6 USB Configuration Les éléments de ce menu vous permettent de modifier les fonctions liées à l’USB. Choisissez un élément puis pressez pour afficher les options de configuration. USB Functions [Enable] Active/désactive les fonctions USB. Options de configuration : [Enabled] [Disabled] USB 2.0 Controller [Enabled] Active/désactive le contrôleur USB 2.0.
2.5.1 Suspend Mode [Auto] 2.5.2 ACPI 2.0 Support [Enabled] 2.5.3 ACPI APIC Support [Enabled] 2.5.4 APM Configuration Vous permet de sélectionner l’état de l’interface ACPI (Advanced Configuration and Power Interface) à utiliser. Options de configuration : [S1 (POS) Only] [S3 Only] [Auto] Allows you to add more tables for Advanced Configuration and Power Interface (ACPI) 2.0 specifications.
VCORE Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage [xx.xxxV] or [Ignored] Le monitoring hardware embarqué détecte automatiquement le voltage de sortie via les régulateurs de tension. Sélectionnez Ignored si vous ne souhaitez pas afficher les voltages détectés. Smart Q-Fan Function [Enabled] Active ou désactive la fonction ASUS Q-Fan pour CPU qui ajuste de manière intelligente la vitesse des ventilateurs, permettant un fonctionnement plus efficace du système.
2.6 Menu Boot (Démarrage) Le menu Boot vous permet de modifier les options de boot du système. Choisissez un élément et pressez pour afficher le sous-menu. Main Advanced Power BIOS SETUP UTILITY Boot Tools Exit Boot Settings Boot Device Priority Boot Settings Configuration Security Specifies the Boot Device Priority sequence. A virtual floppy disk drive (Floppy Drive B:) may appear when you set the CD-ROM drive as the first boot device. Enter F1 F10 ESC 2.6.
Bootup Num-Lock [On] Détermine si le pavé numérique est activé ou non au démarrage du PC. Options de configuration : [Off] [On] Wait for ‘F1’ If Error [Enabled] Réglé sur Enabled, le système attendra que la touche F1 soit pressée lorsque des erreurs surviennent. Options de configuration : [Disabled] [Enabled] Hit ‘DEL’ Message Display [Enabled] Passé sur Enabled, le système affiche le message “Press DEL to run Setup” lors du POST. Options de configuration : [Disabled] [Enabled] 2.6.
Change User Password Choisissez cet élément pour régler ou changer le mot de passe utilisateur. L’élément User Password en haut de l’écran affiche Not Installed par défaut. Après avoir choisi un mot de passe, il affichera Installed. Pour fixer un mot de passe utilisateur : Choisissez Change User Password et pressez . 1. 2. Dans la boîte de mot de passe qui apparaît tapez un mot de passe composé d’un maximum de six lettres et/ou chiffres, puis pressez . 3.
Reset User Data [No] Vous permet d'effacer les données Express Gate de l'utilisateur. Options de configuration : [No] [Reset] Lorsque vous réglez cet élément sur [Reset], assurez-vous d'avoir enregistré vos paramètres dans le BIOS de sorte que les données soient effacées à la prochaine ouverture d'Express Gate. Les données utilisateur incluent les paramètres d'Express Gate ainsi que toutes les informations personnelles stockés dans le navigateur web (marque page, cookies, historique, etc.).
• Cette fonction supporte des disques flash USB au format FAT 32/16 uniquement et utilisant une seule partition. • N’ETEIGNEZ PAS le système et ne le redémarrez pas lors de la mise à jour du BIOS ! Vous provoqueriez une défaillance de démarrage ! • Il est recommandé de mettre à jour le BIOS avec les configurations mémoire/CPU et la version de BIOS identiques. • Seuls les fichiers “xxx.CMO” peuvent être chargés. 2.7.
2.8 Menu Exit (Sortie) Le menu Exit vous permet de charger les valeurs optimales ou par défaut des éléments du BIOS, ainsi que de sauver ou de rejeter les modifications faites dans le BIOS. Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Load Setup Defaults Exit system setup after saving the changes. F10 key can be used for this operation. Appuyer sur ne fait pas immédiatement quitter ce menu. Choisissez l’une des options de ce menu ou pour sortir.
2-24 ASUS M4A78LT-M