NOTEBOOK PC USER’S MANUAL
Product Name: Notebook PC Manual Revision: 1.
SAFETY STATEMENTS Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules.
CTR 21 Approval (for Notebook PC with Modem) Danish Dutch English Finnish French German 4
Greek Italian Portuguese Spanish Swedish 5
Nordic Cautions (for Notebook PC with Lithium-Ion Battery) CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. (English) VORSICHT! Explosionsgetahr bei unsachgemäßen Austausch der Batterie. Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ähnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
Contents USER’S NOTICE 2 SAFETY STATEMENTS Federal Communications Commission Statement ........................................................ 3 Canadian Department of Communications Statement .................................................. 3 CTR 21 Approval (for Notebook PC with Modem) ........................................................ 4 Nordic Cautions (for Notebook PC with Lithium-Ion Battery) ........................................ 6 Macrovision Corporation Product Notice ..................
SECTION 3 GETTING STARTED Power Connection ............................................................................................................ 27 Powering ON Your Notebook PC ..................................................................................... 28 The Power-On Self Test (POST) ................................................................................. 28 Save-to-Disk Partition .....................................................................................................
External Monitor Connection (optional) ............................................................................ 47 PC Cards .......................................................................................................................... 48 32-bit CardBus & Zoomed Video Port ......................................................................... 48 Inserting a PC Card .................................................................................................... 49 Removing a PC Card ...
SECTION 5 BIOS SETUP 65 Updating Your BIOS ......................................................................................................... 65 Creating a BIOS Update Floppy Disk ......................................................................... 65 Updating BIOS Procedures ......................................................................................... 66 BIOS Setup Program .......................................................................................................
1. Introduction SECTION 1 INTRODUCTION About This Product The Notebook PC is the latest in PC technology with features that surpass most desktop PCs. Since the number of features and components are so numerous, there may be different models depending on the territory. Your retailer should provide you with a standard component checklist and a list of optional components for the Notebook PC. Your retailer should also provide you with warranty and technical support.
1. Introduction About This User’s Manual You are reading the Notebook PC User’s Manual. This User’s Manual provides information on the various components in this Notebook PC and how to use them. There are only a few sections in this reference guide as follows: 1. Introduction Introduces you to the Notebook PC and this User’s Manual. 2. Components Gives you information on the Notebook PC’s components. 3. Getting Started Gives you information on getting started with the Notebook PC. 4.
1. Introduction Hardware Features The Notebook PC features a wide range of standard features, upgrades, and options. The following gives you all of your current choices. Many future options are being developed for the Notebook PC to keep up with the latest technologies. • Processor: Pentium® II 300MHz to 400MHz The Notebook PC uses an Intel® µPGA1 socket processor in order to support current and future Intel® processors.
1. Introduction • Modularized Drive Bay: Floppy/CD/DVD-ROM/2nd Hard Drive The Notebook PC comes with a single modularized drive bay in order to accept various drives such as a floppy drive, a CD/DVD-ROM drive, or a second hard disk drive. A Traveler’s drawer is used to cover the bay if no drive is used in order to save power and reduce weight. • Hard Drive: 4, 6, 9, 12GB The Notebook PC comes with a removable 2.5” (6.35cm) wide and .374” (.
Battery: 8-cell Lithium Ion (Li-Ion) 1. Introduction • The Notebook PC supports Lithium-Ion battery pack, which provides 3.3Ah (45W). The battery should last approximately 3 hours under normal conditions and charging takes between 3 to 5 hours depending on whether the Notebook PC is powered OFF, powered ON, or in use during charging. When battery power is 10% or less, there are warning beeps from the speakers and warning messages through the Windows operating system. • Power Adapter: Output 19V DC, 2.
1. Introduction Optional Features and Accessories • CD-ROM: 24X CD or 4X DVD/24X CD The Notebook PC comes in a 24X CD-ROM drive model or a 4X DVD-ROM model (the DVD’s CD-ROM speed is also 24X). The drives can be easily removed by the user to allow swapping with other drives. • Modem/Fax/LAN: 56K V.90, 10/100 Fast-Ethernet Model The Notebook PC comes in a model with or without a built-in 56K/19.2K modem/fax with V.90 compression and data correcting protocols for fast data transfers.
WARNING! 1. Introduction Caring Information The following safety precautions will increase the life of the Notebook PC. Follow all precautions and instructions. Except as described in this manual, refer all servicing to qualified personnel. Do not use damaged power cords, accessories, or other peripherals. Do not use strong solvents such as thinners, benzene or other chemicals on or near the surface. Disconnect the AC power and remove the battery pack(s) before cleaning.
1. Introduction Transporting the Notebook PC To prepare the Notebook PC for transport, you should turn it OFF and disconnect all external peripherals to prevent damage to the connectors. The hard disk drive’s head retracts when the power is turned OFF to prevent scratching of the hard disk surface during transport. Therefore, you should not transport the Notebook PC while the power is still ON.
SECTION 2 COMPONENTS 2. Components Front Side Refer to the diagram below to identify the components on the front side of the Notebook PC. Power Indicator Headphone Jack Battery Indicator Microphone Input Display Panel Latch Front Component Descriptions The following describes the front components of the Notebook PC as shown by the picture above. Power Indicator The green LED will light when the power is ON and blink when in suspend-to-RAM mode. This LED will be OFF when in suspend-to-disk mode.
Top Side Refer to the diagram below to identify the components on the top side of the Notebook PC. 2.
Top Component Descriptions The following describes the components of the Notebook PC as viewed from the top as shown by the illustration on the previous page. 2. Components Display Panel The display panel functions the same as a desktop monitor. It uses either a 12.1” or a 13.3” active matrix TFT LCD, which provides excellent viewing like that of desktop monitors. Unlike desktop monitors, the LCD panel does not produce any radiation or flickering, so it is easier on the eyes.
Bottom Side Refer to the diagram below to identify the components on the bottom side of the Notebook PC. 2. Components Cooling Fan & Vent Removable Drive Drive Lock 1 Reset Button Drive Eject Battery & Drive Lock 2 Battery Release Hard Drive Cover Screw Battery Compartment WARNING! 22 Hard Drive Compartment The bottom of the Notebook PC (especially between the battery and hard drive compartments, and cooling fan) can get very hot.
Bottom Component Descriptions The following describes the components on the bottom side of the Notebook PC as shown by the illustration on the previous page. Cooling Fan & Vent 2. Components The cooling fan turns ON when the temperature rises past a set threshold. The bottom vent brings outside air into the Notebook PC. Do not block the vent! Removable Drive (Described on the Right Side) L Drive Lock 1 The spring latch locks the removable drive. Slide and hold the latch to unlock drive for removal.
Left Side Refer to the diagram below to identify the components on the left side of the Notebook PC. 2. Components Fan Vent DC Input USB Port PCMCIA Socket PCMCIA Eject Left Component Descriptions The following describes the components on the left side of the Notebook PC as shown by the illustration above. Fan Vent The left side fan vent allows outside air to enter the Notebook PC. Do not block the vent! DC IN DC Input The supplied power adapter converts AC power to DC power for use with this jack.
Right Side Refer to the diagram below to identify the components on the right side of the Notebook PC. CD-ROM Eject CD-ROM Activity LED 2. Components CD-ROM Drive CD-ROM Emergency Eject Right Component Descriptions The following describes the components on the right side of the Notebook PC as shown by the illustration above. CD-ROM Drive The Notebook PC comes in a 24X CD-ROM drive model or a 4X DVD-ROM model (the DVD’s CD-ROM speed is also 24X).
Rear Side Refer to the diagram below to identify the components on the rear side of the Notebook PC. Kensington® Lock Port Infrared Port 2. Components Modem/ LAN Port Serial Port Parallel Port VGA Port Docking Port PS/2 Port Rear Vent Rear Component Descriptions The following describes the components on the rear side of the Notebook PC as shown by the illustration above. Infrared Port The infrared (IrDA) communication port allows convenient wireless data transfers.
SECTION 3 GETTING STARTED Power Connection Your Notebook PC comes with a universal AC-DC adapter. That means that you may connect the power cord to any 110V-120V as well as 220V-240V outlets without setting switches or using power converters. Different countries may require that an adapter be used to connect the provided US-standard AC power cord to a different standard. Most hotels will provide universal outlets to support different power cords as well as voltages.
Powering ON Your Notebook PC Press the power switch button momentarily, and the Notebook PC’s power-ON message will appear on the screen followed by a short beep. If necessary, you may adjust the brightness by using the hot keys. If you need to run the BIOS Setup to set or modify the system configuration, press [F2] upon bootup to enter the BIOS Setup. To turn OFF the Notebook PC, push and hold the power switch until the power turns OFF.
Save-to-Disk Partition The Notebook PC supports Advanced Power Management to save battery power and extend its working time. One type of power management is “Save-to-Disk.” Save-to-Disk is a suspend mode where your operating system and application data is saved to a separate partition and retrieved when the Notebook PC comes out of suspend mode. A partition is a space on the hard disk drive equivalent to having a second hard disk drive.
LED Status Indicators There are several LED status indicators on the right of the power button and two on the front edge of the Notebook PC. The LED status indicators give information on the Notebook PC’s current operating and keyboard statuses. The following illustration shows the meaning of each status LED. Activity Indicator Number Lock 1 Capital Lock Scroll Lock Power Indicator Battery Indicator A 3.
Using the Keyboard Specific Hot Keys The following table defines the orange-labeled hot keys on the Notebook PC’s keyboard. The orange-labeled commands can only be accessed by first pressing and holding the (function) key while pressing a key with an orange-labeled command. F1 Places the Notebook PC in suspend mode (either Save-to-RAM or Save-to-Disk depending on BIOS setup). This is not the same as “stand by” in MS Windows. 3.
Microsoft Windows™ Keys There are two special Windows™ keys on the keyboard as described below. The key with the Windows™ Logo activates the Start menu button at the bottom left of the screen. The other key, which looks like a Windows™ menu with a small cursor, activates the properties menu and is equivalent to pressing the right mouse button on a Windows object. Keyboard as a Numeric Keypad 3.
Numeric Keypad as Cursors The numeric keypad can be used as cursors. To enable the cursor keypad, press (the number lock LED will light) and then press and the function desired. For example <8> represents a cursor up command. Num Lk Sys Rq & 7 Home * 8 ( _ ) 9 PgUp * { 6 End PgDn Ins 3. Starting ^ Del [ " + / NOTE: The large bold characters are exaggerated here for your reference. They are not printed on the keyboard as shown here.
3.
SECTION 4 USING THE NOTEBOOK PC Introduction This Section describes the basic features and procedures for using your Notebook PC. Topics covered include the floppy drive, CD-ROM drive, pointing device, and other input and output devices. Storage Device Modules Data storage and retrieval are two of the most fundamental tasks you will perform when working with your computer. The Notebook PC is equipped with a modular drive bay to support a 3.
Floppy Disk Drive External Connection For simultaneous CD-ROM and floppy disk drive use without the PortDock, an external floppy disk drive cable is provided. When installing Windows or anti-virus software, simultaneous CD-ROM and floppy disk drive is required to create a rescue disk during installation. Of course you can skip this step and create a rescue disk later after inserting the floppy disk drive but the time required to turn OFF the Notebook PC and back ON makes it inconvenient.
CD-ROM Drive The Notebook PC includes a CD-ROM module. The CD-ROM drive can support all the popular formats: Audio/Music CDs; Photo CDs; MS-DOS MSCDEX Mode 1 and Mode 2; CD-ROM/XA; CD-I; and Video CDs. CD-ROM Eject CD Activity LED Emergency Eject DVD-ROM Drive Module (optional) The Notebook PC allows for a DVD-ROM module to be purchased instead of the CD-ROM or purchased at a later time. The DVD-ROM allows the use of both CD-ROM and DVD discs. 4.
Getting DVD Support For DVD support on your Notebook PC, you must select the DVD-ROM drive module at the time of purchase instead of the standard CD-ROM or buy the DVD-ROM drive module from your dealer at a later time. The DVD option includes a DVD drive module and drivers. In order to view DVD titles, you must install the provided MPEG2 video decoder software and the DVD viewer software included on the DVD module driver support CD.
NOTE: The CD drive eject button is electronic and requires that the Notebook PC be powered ON in order to eject the CD drive tray. Only one CD may be used at one time on this CD drive. Fr on tP an el Inserting a CD Press the CD drive eject button and the CD drive tray will eject out partially. 2. Hold the CD drive’s front panel and slide the CD drive tray completely out. 3. Place a CD with the printed side facing up. 4. Snap the CD onto the hub by pressing on both sides of the CD’s center.
Inserting and Removing Drive Modules To remove a drive module: 1. Unlock the drive module by sliding the drive lock 2 located on the battery pack towards the front of the Notebook PC from Lock to Unlock in the direction of the arrow as shown in the illustration. 2.
Hard Disk Drive Hard disk drives have higher capacities and operate at much faster speeds than floppy disk drives and CD-ROM drives. Enhanced IDE drives provide a reliable, fast, and cost-effective mass storage solution in the PC storage industry. The high speed transfer modes supported are Ultra DMA/33 up to 33MB/sec and PIO mode 4 up to 16.6MB/sec. The Notebook PC comes with a removable 2.5” (6.35cm) wide and .374” (.
Second Hard Disk Drive Module When using a second hard disk drive module for the first time, a few steps are needed to get it working as follows: 4. Using 42 1. Purchase a hard disk drive module kit from an authorized dealer. 2. Set the jumper to slave (drive 1) according to the manufacturer’s documentation or sticker. 3. Secure the hard disk drive into the hard disk drive module using four screws. 4. Insert into modular bay and check the drive information in BIOS setup.
Pointing Device The Notebook PC’s integrated touchpad pointing device is fully compatible with the two-button PS/2 mouse. The touchpad is pressure sensitive and contains no moving parts; therefore, mechanical failures are unlikely. A device driver is still required for working with some application software. See the Driver & Utility Guide for information on drivers and utilities for the touchpad. Using the Touchpad 4.
Double-clicking/Double-tapping - This is a common skill for launching a program directly from the corresponding icon you select. Move the cursor over the icon you wish to execute, press the left button or tap the pad twice in rapid succession, and the system launches the corresponding program. If the interval between the clicks or taps is too long, the operation will not be executed. You can set the doubleclick speed using the Windows Control Panel “Mouse.” Double-Clicking Double-Tapping 4.
Caring for the Touchpad The touchpad is a pressure sensitive device. If not properly cared for, it can be easily damaged. Take note of the following precautions. • Make sure the touchpad does not come into contact with dirt, liquids or grease. • Do not touch the touchpad if your fingers are dirty or wet. • Do not rest heavy objects on the touchpad or the touchpad buttons. NOTE: The touchpad responds to movement not force. Do not tap the surface too hard.
Display Panel Besides modem and LAN models, the Notebook PC also comes in two display sizes. You may choose from a 12.1” (800x600) or a 13.3” (1024x768) Thin-Film-Transistor (TFT) Active Matrix display panel. You can also connect an external CRT or LCD monitor through the built-in VGA connector on the rear of the Notebook PC. TIP: The provided driver and BIOS allows “Stretch” capability.
Display Panel Care The LCD screen is very delicate and requires careful handling. Pay attention to the following precautions: • • • • • When not in use, keep the display panel closed to prevent dust accumulation. Do not use chemical cleaners on the screen. Wipe only with a dry cloth or tissue. Do not put your fingers or any objects directly on the screen. Do not press or lay any objects on the machine when it is closed. Do not carry the Notebook PC with small or sharp objects (e.g.
PC Cards The Notebook PC has one PC Card socket designed to interface with a Type I or Type II card. It allows you to expand and customize your computer to meet a wide range of application needs. The PC Card standard accommodates a number of function, communication, and data storage expansion options such as Memory/Flash Cards, FAX/Modems, Networking Adapters, and MPEG I/II decoder cards. The Notebook PC supports PCMCIA 2.1, 32bit CardBus, and Zoomed Video (ZV).
Inserting a PC Card Insert the PC card, with the connector side first 2. and label side up, into the socket until it is flush with the Notebook PC’s side. The eject button will protrude out when fully inserted. Flip the eject button forward until it is hidden inside the Notebook PC to lock the PC card in place. 3. Carefully connect any cables or adapters needed by the PC card. Usually a sticker or marking is used on one side of the connector to show the top side. 4. Using 1.
Multimedia Sound System The multimedia sound system features an integrated digital audio controller that produces rich, vibrant sound in high quality 16-bit stereo. With a pair of integrated stereo speakers, a built-in microphone, and both input and output audio jacks for external audio devices, the Notebook PC fulfills most multimedia computing needs. All audio features are software controlled.
IR Wireless Communication The Notebook PC is equipped with an Infrared (IR) Communication Port located on the rear side. The IR port comes with IrDA Serial Infrared Data Link Version 1.1 compliance, which allows you to perform point-to-point wireless communications. You can use a SIR/FIR-specified application to transmit or receive data files with other systems equipped with an infrared port. You must set these modes in the BIOS before you start to install the IR driver and file-transferring applications.
Universal Serial Bus Port Universal Serial Bus (USB) is a peripheral bus standard developed by PC and telecommunication industry leaders that will bring plug and play of computer peripherals outside the system, eliminating the need to install internal expansion cards and drivers. The Notebook PC is equipped with one USB port, which uses a shielded receptacle connector.
AC Power System The Notebook PC power is comprised of two parts, the power adapter and the battery power system. The power adapter converts AC power from a wall outlet to the DC power required by the Notebook PC. The battery pack consists of a set of Lithium-Ion (Li-Ion) battery cells housed together. There is one battery pack inserted in the Notebook PC. The AC Adapter’s primary function is to provide power to the Notebook PC which also charges the battery pack.
Using Battery Power A fully-charged Li-Ion battery pack will provide the system approximately 3 hours of working power. But the actual figure will vary depending on how you use the power saving features, your general work habits, the Notebook PC’s CPU, main memory size and the type of display panel. The “Battery Warning” beeps are automatically enabled in Windows 95/98 and will continually sound when down to 10% (configurable in Windows 98) power.
Inserting and Removing the Battery Pack To remove the battery pack: 2. Slide the battery release latch towards the rear of the Notebook PC and the battery pack will raise out of the Notebook PC. (in direction of the arrow as shown in the illustration) Lock Unlock To insert the battery pack: Unlock the battery and drive lock 2 first. 2. Insert the battery pack with the connector first (see “Partially Removed Battery” illustration). 3.
WARNING! Never attempt to remove the battery pack while the power is ON or if the system has not yet entered into the suspend mode as this may result in the loss of working data. Power Management Modes The Notebook PC has a number of automatic or adjustable power saving features that you can use to maximize battery life and lower Total Cost of Ownership (TCO). You can control some of these features through the Power menu in the BIOS Setup.
Standby Mode In addition to reducing the CPU clock, this mode puts devices including the LCD backlight in their lower active state. The Notebook PC enters Standby mode when the system remains idle for a specified amount of time. The timeout can be set through the BIOS Setup. To resume system operation, press any key on the keyboard, touchpad, or external mouse (or moving the mouse).
System Memory Expansion Under some circumstances, you may find additional memory is required. This is particularly true as applications become more complex. Expanding system memory is one method of increasing system performance by decreasing hard disk access. The Notebook PC comes with 32MB 64-bit high speed SDRAM built-in. One standard 144-pin SO-DIMM socket is available for system memory expansion using common 3.3 Volt 66MHz SDRAM SO-DIMM modules.
Modem Cable The Notebook PC comes in either a modem-only model or a modem and LAN model. Both models come with a modem cable for easy setup while on the road. Press both sides in to release A triangle represents the top side 4. Using Connect this end to a telephone socket using a standard 2- or 4wire telephone cable.
Modem and LAN Connections (optional) The built-in modem and fast-Ethernet model will come with an external cable for connection to RJ-45 Ethernet cabling or to RJ-11 phone cabling. The connector can only be inserted in one orientation and has a triangular icon (or brand name) to represent the top side of the connector. Connect the modem and LAN cable set as shown here.
LAN LED Indicators Speed (100M) Indicator: This green LED monitors connection speeds. The LED lights when connection is made to a 100Base-TX (100Mbit/sec) host. If not lit, the network connection is operating at 10Base-T (10Mbits/sec). When making a connection to a switching hub that supports 100Base-TX full-duplex mode (200Mbit/sec), the LED will also light green. Activity (ACT) Indicator: This orange LED monitors network activity.
Securing Your Notebook PC For system and hard disk drive security, see BIOS setup “Security”. A third party lock such as the ones by Kensington® can be used to secure your Notebook PC physically to an unmovable object. The cable wraps around an object and the “T” shaped end inserts into the Kensington® lock port as shown in this illustration and a key is used to secure the lock in place. For more information, please read the documentation that comes with the Notebook PC lock. 4.
Notebook PC Usage Notes and Examples From Desk to Desk You may want to move your Notebook PC from desk to desk to show something to others, or ask others to review or edit your work. When moving the Notebook PC from desk to desk at work, you can free yourself from all the external peripherals and bring just the Notebook PC. Be sure to: 1. Keep the battery pack fully charged. 2. Log out of the network. 3. Suspend to disk or power OFF the Notebook PC. 4. Disconnect all devices.
Between Countries If you are traveling between countries, it is vital that you travel light but complete. With the modem and LAN model Notebook PC, you simplify accessories to a minimum. A third-party modem and power travel kit is vital for those who wish to use their Notebook PC in uncertain territories. Do not forget to bring extra battery packs so that you do not have to worry about finding power outlets everywhere you go. Be sure to: 1.
SECTION 5 BIOS SETUP Updating Your BIOS PHLASH.EXE is a Flash Memory Writer utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the Notebook PC’s motherboard. This file works only in DOS mode. To determine the BIOS version, check the code (e.g. BIOS Ver. XXXXX) displayed on the upper left-hand corner of your screen just before entering BIOS setup (after pressing the F2 key). Larger numbers represent a newer BIOS version. Creating a BIOS Update Floppy Disk 1.
Updating BIOS Procedures WARNING! 1. Boot from the BIOS floppy disk you created earlier. NOTE: BIOS setup must specify “Floppy Drive” as the first item in the boot sequence. (see Boot Menu) 2. At the “A:\” prompt, type “phlash/mode=3 xxxx.rom (xxxx being the name of the BIOS file) and then press . WARNING! 5.
BIOS Setup Program This Notebook PC supports a programmable EEPROM that stores the BIOS software and can be updated using the provided utility as described in Flash Memory Writer Utility. This Section will guide you through the BIOS setup program by providing clear explanations for all the options. A default configuration has already been set. If you are either installing new devices or expanding main memory, you will need to enter the BIOS Setup to reconfigure your Notebook PC.
BIOS Menu Bar The top of the screen has a menu bar with the following selections: MAIN ADVANCED SECURITY POWER BOOT EXIT Use this menu to make changes to the basic system configuration. Use this menu to enable and make changes to the advanced features Use this menu to set a password to control bootup and control access to the BIOS setup menu. Use this menu to configure and enable Power Management features. Use this menu to configure the default system device used to locate and load the Operating System.
General Help In addition to the Item Specific Help window, the BIOS setup program also provides a General Help screen. This screen can be called up from any menu by simply pressing or the + combination. The General Help screen lists the legend keys with their corresponding alternates and functions. Saving Changes and Exiting the Setup Program See Exit Menu for detailed information on saving changes and exiting the setup program.
Main Menu When the Setup program is accessed, the main menu screen appears as shown: Main Advanced PhoenixBIOS Setup Utility Security Power Boot Exit Item Specific Help System Time: System Date: [16:55:39] [05/02/1999] Diskette A: 1.44MB IDE Primary Master IDE Primary Slave [4327MB] [None] Video Display Device: System Memory Extended Memory [LCD & CRT] 640 KB 31744 KB , , or selects field .
Video Display Device: [LCD & CRT] This field allows you to select and enable video display devices, such as an LCD panel, an external CRT/LCD monitor, or both. The configuration options are: [LCD] [CRT] [LCD & CRT] System Memory: This field displays the amount of conventional memory detected by the system during bootup. You do not need to make changes to this field. This is a display only field. Extended Memory: This field displays the amount of extended memory detected by the system during bootup.
Type: Select Auto to automatically detect an IDE type drive. This option only works with standard builtin IDE drives. If automatic detection is successful, the correct values will be filled in for the remaining fields on this sub-menu. To configure a drive, select User. Manually enter the number of cylinders, heads and sectors per track for your drive. Refer to your drive documentation or look on the drive for this information.
32 Bit I/O: When enabled, this option speeds up communication between the CPU and the IDE controller. This option supports PCI local bus only. ISA bus is not supported. NOTE: To make changes to this field, the Type field must be set to User. The configuration options are: [Disabled] [Enabled] Transfer Mode: When enabled, this option speeds up communication between the system and the IDE controller by using enhanced I/O transfer modes (PIO Modes).
IDE Primary Slave In this field, indicate the size of a disk drive or the device type, such as a CD-ROM drive. The arrow head icon indicates that this field contains a sub-menu. The sub-menu is used to configure the IDE Hard Disk installed in the system. To configure a hard disk drive, move the cursor to highlight the IDE Primary Slave field, and press [Enter]. The following sub-menu screen will appear. The fields and options on this sub-menu are the same as the previous menu described earlier.
Advanced Menu Selecting Advanced from the main menu bar display the Advanced menu as shown below. Main Advanced PhoenixBIOS Setup Utility Security Power Boot Exit Item Specific Help Installed O/S: [Win95/98/2000] I/O Device Configuration Large Disk Access Mode: Display Expansion: Internal Pointing Device: Num Lock: Anti-Virus Feature: QuickBoot Mode: [Normal] [Enabled] [Enabled] [Auto] [Enabled] [Enabled] Select the operating system installed on your system which you will use most commonly.
Display Expansion: [Enabled] DOS and other applications outside of Windows usually only displays at 640x480 resolution and will not fill the entire Notebook PC’s display panel. When Display Expansion is Enabled, the screens will be stretched to fill the display panel. Because this may distort or blur certain DOS application screens, this function can also be Disabled. Internal Pointing Device: [Enabled] This field allows you to enable or disable the internal pointing device.
I/O Device Configuration Main Advanced PhoenixBIOS Setup Utility Security Power Boot I/O Device Configuration Seral port A: Base I/O address: IR Port Base I/O address: Mode: DMA channel: Parallel Port: Mode: Base I/O address: [User] [3F8 IRQ4] [User] [2F8 IRQ3] [FIR] [DMA 3] [User] [EPP] [378/IRQ7] Exit Item Specific Help Configure serial port A using options: Auto [OS configuration] User [USER configuration] Disabled [NO configuration] NOTE: The presence of sub-items in this menu is dependent on cer
Mode: (when User is selected in IR port) When User is selected, the Mode field allows you to select either Standard Infrared (SIR) or Fast Infrared (FIR) communication mode. The configuration options are: [SIR] [FIR] DMA channel: (when User is selected in IR port) The DMA Channel field allows you to configure the Parallel port DMA Channel for the selected ECP mode. NOTE: This field is only available when the Parallel port field is set to User and the Mode field is set to ECP.
Security Menu The Notebook PC’s advanced system of security allows you to set a password to prevent unauthorized access to system resources, data, and the BIOS Setup Program. This Section covers each parameter of the Security Setup.
Security Menu Details System Boot Entry Set Password: This field allows you to set the User password. To set the User password, highlight this field and press [Enter]. Type the password and press [Enter]. You can type up to eight alphanumeric characters. Symbols and other keys are ignored. To confirm the password, type the password again and press the [Enter]. The User password is now set. This password allows full access to the BIOS Setup menus.
The Power Menu The Power menu of the Setup program allows you to enable and adjust the advanced features of the Notebook PC, which are designed to conserve power. Enabling these features will extend the life of the battery pack between charges. To make changes to power management settings, select Power Savings from the menu bar.
Suspend Mode: [Save to RAM] This field determines the type of suspend mode when the Notebook PC enters power saving. The configuration options are: [Save To RAM] [Save To Disk] Standby Timeout: [Off] This option is only enabled when Customized is selected in the Power Savings field. This field allows you to specify the period of inactivity before the system automatically switches to Standby mode.
Boot Menu The Boot menu allows the user to specify the order in which the Notebook PC is to check for a device to boot the system. To make changes, select Boot from the menu bar and the following screen appears: Main Advanced PhoenixBIOS Setup Utility Security Power Boot Exit Item Specific Help 1. 2. 3. [Hard Drive] [ATAPI CD-ROM Drive] [Floppy Drive] Use <↑> or <↓> to select a device, then press <+> to move it up the list, or <-> to move it down the list. Press to exit this menu.
Exit Menu Once you have made all of your selections from the various menus in the Setup program, you should save your changes and exit Setup. Select Exit from the menu bar to display the following menu: Main Advanced PhoenixBIOS Setup Utility Security Power Boot Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes Exit System Setup and save your changes to CMOS . NOTE: Pressing the [Esc] key does not exit this menu.
Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When this option is selected or if [F9] is pressed, a confirmation is requested. Select Yes to load default values. You can now select Exit Saving Changes or make other changes before saving the values to the nonvolatile RAM. Discard Changes This option allows you to discard the selections you made and restore the values you previously saved.
5.
APPENDIX PortDock Accessory This section is provided for the optional PortDock accessory for the Notebook PC. The main purpose fo the PortDock is to provide a desktop docking solution and extra drive bays for simultaneous CD/DVD-ROM, floppy, and second hard disk drive use. Front View Triangular icon or brand name faces up.
NOTES: • Except for the USB port, the ports on the Notebook PC will not function and should not have any devices (e.g. monitor, mouse, keyboard) connected when using the PortDock. • The PortDock’s power requirements require that a power adapter be connected to the PortDock or to the Notebook PC. • The PortDock reset button resets the PortDock, not the Notebook PC. If the PortDock or the Notebook PC does not respond, try resetting the PortDock before resetting the Notebook PC.
Docking Solution For long-term use of the Notebook PC or if the Notebook PC is intended to be a desktop replacement computer, the PortDock provides a convient docking solution. A desktop PS/2 mouse, PS/2 keyboard, stereo speakers, monitor, printer, serial device, and Notebook PC power can all be connected to the PortDock. When the Notebook PC is used on a permanent desk, the single docking connector can be easily used to connect or disconnect all of these desktop peripherals at once.
PortBar Accessory This section is provided for the optional PortBar accessory for the Notebook PC. The main purpose of the PortBar is to provide a simple inexpensive desktop docking solution as compared to traditional bulky port replicators. Serial Port Monitor Port PS/2 Mouse PS/2 Keyboard USB Port 1 USB Port 2 Parallel Port Triangular icon or brand name faces up.
Docking Solution For long-term use of the Notebook PC or if the Notebook PC is intended to be a desktop replacement computer, the PortBar provides a convient docking solution. A desktop PS/2 mouse, PS/2 keyboard, monitor, printer, serial device, and Notebook PC power can all be connected to the PortBar. Like the PortDock, the PortBar also requires USB devices to be connected to the Notebook PC.
Vehicle/Air Power Adapter Accessory This section is provided for the optional vehical/air power adapter accessory for the Notebook PC. The main purpose of the vehicle/air power adapter is to provide a source of power for using the Notebook PC and/or charging the Notebook PC’s battery from a 12VDC recepticle such as those found in vehicles and certain airplanes.
DVD-ROM Model The following information pertains to the optional DVD drive module. The following specifications are for general reference only and may change without notice. Features and Specifications • • • • • • • • • • • 12.
Internal Modem Model Protocols and Compliancy The Notebook PC with internal modem model complies with JATE (Japan), FCC (US, Canada, Korea, Taiwan), and CTR21. The internal modem has been approved in accordance with Council Decision 98/482/EC for pan-European single terminal connection to the public switched telephone network (PSTN).
This table shows the countries currently under the CTR21 standard.
Appendix 96
Glossary ACPI (Advanced Configuration and Power Managment Interface) Modern standard for reducing power usage in computers. AUTOEXEC.BAT AUTOEXEC.BAT is a special-purpose file that is automatically executed by DOS whenever the computer is turned ON or restarted. This file contains important commands that help configure the system to work with certain software and devices. Windows 95 and later has its own startup files and may not use or may ignore parts of the AUTOEXEC.BAT file.
CPU (Central Processing Unit) The CPU, sometimes called “Processor,” actually functions as the “brain” of the computer. It interprets and executes program commands and processes data stored in memory. Device Driver A device driver is a special set of instructions that allows the computer’s operating system to communicate with devices such as VGA, audio, ethernet, printer, or modem.
PS/2 Port PS/2 ports are based on IBM Micro Channel Architecture. This type of architecture transfers data through a 16-bit or 32-bit bus. A PS/2 mouse and/or keyboard may be used on ATX motherboards. RAM (Random Access Memory) There are several different types of RAM such as DRAM (Dynamic RAM), EDO DRAM (Extended Data Output DRAM), SDRAM (Synchronous DRAM). ROM (Read Only Memory) ROM is nonvolatile memory used to store permanent programs (called firmware) used in certain computer components.
Notebook PC Owner Information This page is provided for recording information concerning your Notebook PC for future reference or for technical support. Keep this User’s Manual in a secured location if passwords are filled out.
USER’S NOTICE No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Manufacturer Contact Information ASUSTeK COMPUTER INC. (Asia-Pacific) Marketing Address: Telephone: Fax: Email: 150 Li-Te Road, Peitou, Taipei, Taiwan 112 +886-2-2894-3447 +886-2-2894-3449 info@asus.com.tw Technical Support MB/Other (tel): Notebook (tel): Server (tel): Fax: Email: Newsgroup: WWW: FTP: English: +886-2-2890-7121 English: +886-2-2890-7122 English: +886-2-2890-7123 +886-2-2895-9254 tsd@asus.com.tw news2.asus.com.tw www.asus.com.tw ftp.asus.com.
