Motherboard MAXIMUS VI EXTREME
E7948 First Edition April 2013 Copyright © 2013 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Safety information...................................................................................................... vii About this guide........................................................................................................ viii MAXIMUS VI EXTREME specifications summary..................................................... x OC Panel specifications summary........................................................................... xv Package contents............................
2.2 2.3 2.4 BIOS update utility.................................................................................... 2-15 Motherboard rear and audio connections.............................................. 2-16 2.3.1 2.3.2 2.6 2.4.1 OC Panel Overview................................................................... 2-21 2.4.3 Setting up your OC Panel in Extreme Mode.............................. 2-25 3.2 3.3 3.4 3.5 3.6 Turning off the computer...................................................
3.11 Updating BIOS........................................................................................... 3-52 3.11.1 ASUS EZ Flash 2....................................................................... 3-53 3.11.3 ASUS BIOS Updater.................................................................. 3-55 3.11.2 3.12 Secure Erase............................................................................................. 3-58 Chapter 4: 4.1 4.2 4.3 4.4 Support DVD information..................
Appendices Notices ..................................................................................................................... A-1 ASUS contact information.......................................................................................
Safety information Electrical safety • • • • • • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This guide contains the following parts: • • • • • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports. It includes description of the switches, jumpers, and connectors on the motherboard.
Conventions used in this guide To ensure that you perform certain tasks properly, take note of the following symbols used throughout this manual. DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task IMPORTANT: Instructions that you MUST follow to complete a task. . NOTE: Tips and additional information to help you complete a task.
MAXIMUS VI EXTREME specifications summary LGA1150 socket for 4th Generation Intel® Core™ i7 / Intel® Core™ i5 / Intel® Core™ i3, Pentium®, Celeron® Processors Supports 22nm CPU CPU Supports Intel® Turbo Boost Technology 2.0* * The Intel® Turbo Boost Technology 2.0 support depends on the CPU type. ** Refer to www.support.asus.com/cpu.aspx for Intel CPU support list. Chipset Intel® Z87 Express Chipset Dual channel memory architecture Memory 4 x DIMM, max. 32GB, DDR3 2800(O.C.) / 2666(O.C.) / 2600(O.C.
Intel® Z87 Express Chipset: Storage 6 x SATA 6.0 Gb/s ports* - Intel® Rapid Storage 12 supports RAID 0, 1, 5, and 10 - Intel® Smart Response Technology, Intel® Rapid Start Technology, and Intel® Smart Connect Technology** 1 x M.2 (NGFF) SSD Slot B on mPCIe Combo II expansion card - Supports PCI Express 2.0 x1 and SATA 6Gb/s standard - Supports M.2 (NGFF) Type 2242 (22mm x 42mm) SSD card ASMedia® SATA 6Gb/s controller: - 4 x SATA 6.0 Gb/s ports *** * SATA 6Gb/s port 5 will be disabled when M.
ROG Extreme OC Kit - EZ Plug - LN2 Mode - Slow Mode - PCIe x16 Lane switch ROG Connect - RC Diagram - RC Remote - RC Poster ROG Exclusive Features ROG Extreme Engine Digi+ III - Full digital 8+2 phase CPU/DRAM power - NexFETTM Power Block MOSFET - 60A BlackWing Chokes - 10K Black Metallic Capacitors mPCIe Combo II (mPCIe/M.2 (NGFF) combo card) UEFI BIOS features - ROG BIOS Print - GPU.DIMM Post - Extreme Tweaker - Tweaker’s Paradise - ROG SSD Secure Erase - O.C.
ASUS EZ DIY - ASUS BIOS Flashback - ASUS CrashFree BIOS 3 - ASUS EZ Flash 2 - ASUS C.P.R. (CPU Parameter Recall) Special Features ASUS Q-Design - ASUS Q-Code - ASUS Q-Shield - ASUS Q-Connector - ASUS Q-LED (CPU, DRAM, VGA, Boot Device LED) - ASUS Q-Slot - ASUS Q-DIMM 1 x Clear CMOS button 1 x ROG Connect button 2 x USB 2.0 ports (1 port can be switched to ROG Connect) 6 x USB 3.
1 x Front panel audio connector (AAFP) 1 x System panel connector Internal Connectors 1 x mPCIe Combo II connector 1 x Directkey button 1 x DRCT (DirectKey) header 1 x FastBoot switch 1 x User’s manual 1 x I/O Shield OC Panel Kit - 1 x OC Panel - 1 x OC Panel 5.25-inch drive bay metal case - 1 x OC Panel cable - Set of screws (1 x 2 pcs) ; (1 x 4 pcs) 1 x mPCIe Combo II card with dual-band WiFi 802.11 a/b/g/n/ac + Bluetooth v4.0/3.
OC Panel specifications summary Display 2.
Package contents Check your motherboard package for the following items. Motherboard ROG MAXIMUS VI EXTREME Cables 1 x ROG Connect cable 5 x 2-in-1 SATA 6.0 Gb/s signal cables 1 x 4-WAY SLI® bridge 1 x 3-WAY SLI® bridge 1 x SLI® cable 1 x CrossFireTM cable 1 x ROG_EXT cable Accessories 1 x I/O Shield 1 x OC Panel 1 x OC Panel 5.
Installation tools and components 1 bag of screws Philips (cross) screwdriver PC chassis Power supply unit Intel LGA 1150 CPU Intel LGA 1150 compatible CPU Fan DDR3 DIMM SATA hard disk drive SATA optical disc drive (optional) Graphics card (optional) The tools and components in the table above are not included in the motherboard package.
xviii
Chapter 1: Product Introduction Product introduction 1.1 Special features 1.1.1 Product highlights 1 Republic of Gamers The Republic of Gamers offers you the best of the best. We offer the best hardware engineering, the fastest performance, the most innovative ideas, and we welcome the best gamers to join in. In the Republic of Gamers, mercy rules are only for the weak, and bragging rights means everything. We believe in making statements and we excel in competitions.
1.1.2 ROG Intelligent Performance & Overclocking features mPCIe Combo II ROG mPCIe Combo II offers expandability solutions with the latest connectivity standards via the proprietary connector onboard. It provides your system with the fastest Wi-Fi 802.11ac and Bluetooth 4.0 connection. It also features the M.2 (NGFF) slot for an optimal system performance. ROG Connect ROG Connect allows you to monitor the status of your desktop PC and tweak its parameters in real-time via a notebook.
ProbeIt This motherboard consists of eleven (11) ProbeIt measurement points that helps you detect your system’s current voltage. With the use of a multimeter device, these points can help measure your system’s Vcore, PCH, IO (Digital/Analog), DRAM, iGPU, System agent and other critical voltages. Extreme Tweaker Extreme Tweaker is the one stop shop to fine-tune your system to optimal performance.
1.1.3 ASUS special features Wi-Fi GO! ASUS Wi-Fi GO! leads the way to a more enjoyable home entertainment. With ASUS Wi-Fi GO!, you can wirelessly stream media files to DLNA devices, remotely control and access your computer using your mobile device, and easily transfer files between your computer and mobile device.
ROG RAMDisk Chapter 1 RAMDisk reserves part of system memory and turns it into actual storage, so you can place favorite app and game cache files in it to enjoy high-speed RAM performance while accessing them. Plus, this extends SSD lifespan and keeps your main storage optimized for really important tasks, and you get auto data backup and restore.
1.2 Motherboard overview 1.2.1 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity. • Hold components by the edges to avoid touching the ICs on them.
1.2.2 Motherboard layout Chapter 1 Refer to 1.2.9 Internal connectors and 2.3.1 Rear I/O connection for more information about rear panel connectors and internal connectors.
Layout contents Connectors/Jumpers/Buttons and switches/Slots 1. Power connectors (24-pin EATXPWR, 8-pin EATX12V, 4-pin EATX12V) 2. LGA1150 CPU Socket 3. CPU, chassis, and optional fan connectors (4-pin CPU_FAN, 4-pin CPU_OPT, 4-pin OPT_FAN1-3, 4-pin CHA_FAN1-3) 4. DDR3 DIMM slots 5. Q_Code LEDs 6. PCIe x16 Lane switch 7. START (Power-on) button 8. Slow Mode switch 9. RESET button 10. MemOK! button 11. Thermal sensor cable connectors (2-pin OPT_TEMP1-3) 12. USB 3.0 connectors (20-1 pin USB3_12) 13.
1.2.3 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA1150 socket designed for the 4th Generation Intel® Core™ i7 / Intel® Core™ i5 / Intel® Core™ i3, Pentium®, and Celeron® processors. Ensure that all power cables are unplugged before installing the CPU. • Ensure that you install the correct CPU designed for LGA1150 only. DO NOT install a CPU designed for LGA1155 and LGA1156 sockets on the LGA1150 socket.
1.2.4 System memory The motherboard comes with four Double Data Rate 3 (DDR3) Dual Inline Memory Modules (DIMM) slots. A DDR3 module is notched differently from a DDR or DDR2 module. DO NOT install a DDR or DDR2 memory module to the DDR3 slot.
Memory configurations You may install 1GB, 2GB, 4GB and 8GB unbuffered and non‑ECC DDR3 DIMMs into the DIMM sockets. • Memory module with memory frequency higher than 2133 MHz and its corresponding timing or the loaded XMP profile is not the JEDEC memory standard. The stability and compatibility of these memory modules depend on the CPU’s capabilities and other installed devices. • You may install varying memory sizes in Channel A and Channel B.
MAXIMUS VI EXTREME Motherboard Qualified Vendors Lists (QVL) DDR3 2800 MHz capability DIMM socket support (Optional) Vendors Part No. Size SS/ DS Chip Brand Chip NO. Timing Voltage 2 4 AVEXIR AVD3U28001204G-4CI 16GB (4x4GB) DS - - 12-14-14-35 1.65V • • CORSAIR CMD16GX3M4A2800C11 16GB (4x4GB) DS - - 11-14-14-35 1.65V • • CORSAIR CMD16GX3M4A2800C12 16GB (4x4GB) DS - - 12-14-14-36 1.65V • • G.SKILL F3-2800C11D-8GTXD 8GB (2x4GB) DS - - 11-13-13-35 1.65V • • G.
DDR3 2200 MHz capability Vendors Part No. Size SS/ DS Chip Brand Chip NO. Timing Voltage G.SKILL F3-17600CL7D-4GBFLS(XMP) 4G (2x2GB) DS - - 7-10-10-28 1.65 DIMM socket support (Optional) 2 4 • DDR3 2133 MHz capability DIMM socket support (Optional) Vendors Part No. Size SS/ DS Chip Brand Chip NO. Timing Voltage 2 4 A-DATA AX3U2133XC4G10(XMP) 4GB DS - - 10-11-11-30 1.65 • • A-DATA AX3U2133XW8G10(XMP) 16GB (2x 8GB) DS - - 10-11-11-30 1.65 • • Apacer 78.
DDR3 2000 MHz capability DIMM socket support (Optional) Vendors Part No. Size SS/ DS Chip Brand Chip NO. Timing Voltage 2 4 Patriot PV736G2000ELK(XMP) 6GB (3x2GB) DS - - 7-7-7-20 1.65 • • Silicon Power SP002GBLYU200S02(XMP) 2GB DS - - - - • • Team TXD32048M2000C9(XMP) 2GB DS Team T3D1288RT-20 9-9-9-24 1.5 • • Team TXD32048M2000C9-L(XMP) 2GB DS Team T3D1288RT-20 9-9-9-24 1.6 • • DDR3 1866 MHz capability Chip Brand Chip NO.
DDR3 1600 MHz capability Part No. Size SS/DS Chip Brand Chip NO. Timing Voltage 2 4 A-DATA AD3U1600C4G11 4GB DS MICRON D9PFJ 11-1111-28 - • • A-DATA AD3U1600W4G11 4GB SS A-DATA 3WCD-1211A 11-1111-28 - • • A-DATA AD3U1600W8G11 8GB DS A-DATA 3WCD-1211A 11-1111-28 - • • A-DATA AX3U1600W8G11 16GB (2x8GB) DS - - 9-119-27 1.5 • • A-DATA AXDU1600GW8G9 B(XMP) 16GB (2x8GB) DS - - 9-119-27 1.65 • • AMD AE32G1609U1-U 2GB SS AMD 23EY4587MB6H - 1.
DDR3 1600 MHz capability DIMM socket support (Optional) Vendors Part No. Size SS/DS Chip Brand Chip NO. Timing Voltage 2 4 KINGSTON KHX1600C9D3K3/ 6GX(XMP) 6GB (3x2GB) DS - - 9 1.65 • • KINGSTON KHX1600C9D3P1K2/8G 8GB (2x4GB) DS - - 9 1.5 • • KINGTIGER KTG2G1600PG3(XMP) 2GB DS - - - - • • MICRON MT16JTF1G64AZ1G6D1 8GB DS MICRON D9PBC - 1.
DDR3 1333 MHz capability DIMM socket support (Optional) Vendors Part No. Size SS/ DS Chip Brand Chip NO. Timing Voltage 2 4 ACTICA ACT4GHU64B8H1333H 4GB DS Hynix H5TQ2G83AFR - - • • ACTICA ACT4GHU72D8H1333H 4GB DS Hynix H5TQ2G83AFR(ECC) - - • • AMD AE32G1339U1-U 2GB SS AMD 23EY4587MB3H - 1.5 • • AMD AE34G1339U2-U 4GB DS AMD 23EY4587MB3H - 1.5 • • Apacer 78.A1GC6.9L1 2GB DS Apacer AM5D5808FEQSBG 9 - • • Apacer 78.B1GDE.
DIMM socket support (Optional) Vendors Part No. Size SS/ DS 2 4 Mach Xtreme MXD3U133316GQ 16GB (4x 4GB) DS - - - - • • Mach Xtreme MXD3V13332GS 2GB SS Mach Xtreme C2S46D30-D313 - - • • MICRON MT8JTF25664AZ1G4M1 2GB SS MICRON D9PFJ - - • • OCZ OCZ3G1333LV4GK 4GB (2x 2GB) DS - - 9-9-9 1.65 • OCZ OCZ3G1333LV8GK 8GB (2x 4GB) DS - - 9-9-9 1.65 • Patriot PG38G1333EL(XMP) 8GB DS - - - 1.
1.2.5 Expansion slots Unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. Slot Description 1 PCIe 3.0/2.0 x16/x8_1 slot 2 PCIe 3.0/2.0 x16_A2 slot 3 PCIe 3.0/2.0 x8_B2 slot 4 PCIe 3.0/2.0 x8_3 slot 5 PCIe 2.0/1.1 x4_1 slot 6 PCIe 3.0/2.0 x8_4 slot ASUS MAXIMUS VI EXTREME Chapter 1 Slot No.
VGA Configuration PCIe 3.0/2.0_x16/x8_1 PCIe Express 3.0 operating mode Single VGA SLI/ CrossFireX 3-WAY SLI/ CrossFireX 4-WAY SLI/ CrossfireX x16 (Native) x8 (Native) x8 (Native) x8 (Native) x16 x16 – – PCIe 3.0/2.0_x16_A2 – – PCIe 3.0/2.0_x8_B2 – PCIe 3.0/2.0_x8_3 – – x8 x8 PCIe 3.0/2.0_x8_4 – – – x8 x8 (Native) • We recommend that you provide sufficient power when running CrossFireX™ or SLI® mode.
IRQ assignments for this motherboard A PCIE_x16/x8_1 PCIE_x8_B2 PCIE_x4_1 I.G.F.X. Intel LAN Controller SATA #0 SATA #1 High Definition Audio EHCI# 0 (USB 2.0) EHCI# 1 (USB 2.0) C D E F G H shared – – – – – – – – shared – – – – – – – – – – – – – – shared – – shared shared – – – – – – – – – – – – – – – – – – – – – shared – shared – shared – – – – – shared – – – – – – – – – – – – – – – – – – – shared – – shared – – Chapter 1 XHCI (USB 3.
1.2.6 Onboard buttons and switches Onboard switches and buttons allow you to fine-tune performance when working on a bare or open-case system. This is ideal for overclockers and gamers who continually change settings to enhance system performance. 1. 2. Power-on button The motherboard comes with a power-on button that allows you to power up or wake up the system.
MemOK! button Installing DIMMs that are not compatible with the motherboard may cause system boot failure, and the DRAM_LED near the MemOK! switch lights continuously. Press and hold the MemOK! button until the DRAM_LED smemory compatibility tuning for successful boot. • Refer to section 1.2.7 Onboard LEDs for the exact location of the DRAM_LED. • The DRAM_LED also lights up when the DIMM is not properly installed. Turn off the system and reinstall the DIMM before using the MemOK! function.
4. BIOS Switch button The motherboard comes with two BIOS. Press the BIOS button to switch BIOS and load different BIOS settings. The nearby BIOS LEDs indicate the BIOS you are using. 5. Slow Mode switch Slow Mode switch allows your system to provide better overclocking margins when using the LN2 cooling system. When enabled, the Slow Mode switch prevents the system from crashing, slows down the CPU, and the system’s tuner will make the adjustments.
6. This DIP switch allows you to enable and disable the corresponding PCIe x16 slots. When one of the installed PCIe x16 cards is out of order, you can slide the switch to find out the faulty one without removing the cards. Fast Boot switch This switch allows you to enable or disable the Fast Boot feature. When enabled, the system boot speed is accelerated. Chapter 1 7.
8. DirectKey button This feature allows your system to go to the BIOS Setup program with the press of a button. With DirectKey, you can enter the BIOS anytime without having to press the key during POST. It also allows you to turn on or turn off your system and conveniently enter the BIOS during boot-up. Ensure to save your data before using the DirectKey button. • When the system is on and you press the DirectKey button, your system will shut down.
1.2.7 1. Jumpers LN2 Mode jumper (3-pin LN2_MODE) When enabled, the LN2 Mode jumper allows your system to eliminate the cold bug* in the processor during POST. It allows the processor to run at an extremely low temperature and helps the system boot fast. Chapter 1 * The cold bug is an issue with CPUs that causes to fail to boot at low (usually sub zero) temperatures.
1.2.8 1. 2. Onboard LEDs Hard Disk LED The hard disk LED is designed to indicate the hard disk activity. It blinks when data is being written into or read from the hard disk drive. The LED does not light up when there is no hard disk drive connected to the motherboard or when the hard disk drive does not function. MemOK! LED Blinking: Indicates that MemOK! is enabled before POST. Lit: Indicates that the system loads the preset profile (GO_Button file) for temporary overclocking when in OS.
3. Q LEDs check key components (CPU, DRAM, VGA card, and booting devices) in sequence during motherboard booting process. If an error is found , the corresponding LED will continue lighting until the problem is solved. This user-friendly design provides an intuitive way to locate the root problem within seconds. Power LED The motherboard comes with a power-on button that lights up to indicate that the system is ON, in sleep mode, or in soft‑off mode.
5. BIOS LED The BIOS LEDs help indicate the BIOS activity. Press the BIOS button to switch between BIOS1 and BIOS2 and the LED lights up when the corresponding BIOS is in use. 6. Q-Code LEDs The Q-Code LED design provides you with a 2-digit error code that displays the system status. Refer to the Q-Code table on the next page for details.
Q-Code table Code Description 00 Not used 01 Power on. Reset type detection (soft/hard).
Q-Code table Chapter 1 Code Description 50 – 53 Memory initialization error. Invalid memory type or incompatible memory speed 54 Unspecified memory initialization error 55 Memory not installed 56 Invalid CPU type or Speed 57 CPU mismatch 58 CPU self test failed or possible CPU cache error 59 CPU micro-code is not found or micro-code update is failed 00 Not used 01 Power on. Reset type detection (soft/hard).
Code Description 3B – 3E Post-Memory PCH initialization is started 4F DXE IPL is started 50 – 53 Memory initialization error.
Q-Code table Chapter 1 Code Description F9 Recovery capsule is not found FA Invalid recovery capsule FB – FF Reserved for future AMI error codes 60 DXE Core is started 61 NVRAM initialization 62 Installation of the PCH Runtime Services 63 – 67 CPU DXE initialization is started 68 PCI host bridge initialization 69 System Agent DXE initialization is started 6A System Agent DXE SMM initialization is started 6B – 6F System Agent DXE initialization (System Agent module specific) 70 PCH
Code Description 9C USB Detect 9D USB Enable 9E – 9F Reserved for future AMI codes A0 IDE initialization is started A1 IDE Reset A2 IDE Detect A3 IDE Enable A4 SCSI initialization is started A5 SCSI Reset A6 SCSI Detect A7 SCSI Enable A8 Setup Verifying Password A9 Start of Setup AA Reserved for ASL (see ASL Status Codes section below) AB Setup Input Wait AC Reserved for ASL (see ASL Status Codes section below) AD Ready To Boot event AE Legacy Boot event AF Exit Boot S
Q-Code table Code Description D2 PCH initialization error D3 Some of the Architectural Protocols are not available D4 PCI resource allocation error.
1.2.9 1. Internal connectors Intel Z87 Serial ATA 6.0 Gb/s connectors (7-pin SATA6G_1-6 [red]) ® These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA 6.0 Gb/s signal cables. • These connectors are set to [AHCI Mode] by default. If you intend to create a Serial ATA RAID set using these connectors, set the SATA Mode item in the BIOS to [RAID Mode]. Refer to section 3.6.3 SATA Configuration for details. • Before creating a RAID set, refer to section 5.
3. 4. Chapter 1 1-38 ASMedia® Serial ATA 6.0 Gb/s connectors (7-pin SATA6G_E12/E34 [red]) These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA 6.0 Gb/s signal cables. USB 3.0 connector (20-1 pin USB3_12) This connector allows you to connect a USB 3.0 module for additional USB 3.0 front or rear panel ports. With an installed USB 3.0 module, you can enjoy all the benefits of USB 3.
5. Digital audio connector (4-1 pin SPDIF_OUT) This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port. Connect the S/PDIF Out module cable to this connector, then install the module to a slot opening at the back of the system chassis. Chapter 1 The S/PDIF module is purchased separately.
6. USB 2.0 connectors (10-1 pin USB910; USB1112; USB1314) These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to 48 MBps connection speed. Never connect a 1394 cable to the USB connectors.
7. CPU, chassis, and optional fan connectors (4-pin CPU_FAN; 4-pin CPU_OPT; 4-pin CHA_FAN1-3; OPT_FAN1-3) • DO NOT forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! Do not place jumper caps on the fan connectors! • Ensure to fully insert the 4-pin CPU fan cable to the CPU fan connector. • The CPU_FAN connector supports the CPU fan of maximum 1A (12 W) fan power.
8. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector. • We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s high-definition audio capability.
ATX power connectors (24-pin EATXPWR; 8-pin EATX12V_1; 4-pin EATX12V_2) These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. • For a fully configured system, we recommend that you use a power supply unit (PSU) that complies with ATX 12 V Specification 2.0 (or later version) and provides a minimum power of 350 W.
10. • • • • • System panel connector (20-8 pin PANEL) This connector supports several chassis-mounted functions. System power LED (2-pin PLED) This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. Hard disk drive activity LED (2-pin HDD_LED) This 2-pin connector is for the HDD Activity LED.
12. EZ Plug connectors (6-pin EZ_PLUG_1; 4-pin EZ_PLUG_2) These connectors provide additional power to PCIe_x16 slots and back IO ports. Connect a 6-pin power cable to EZ_PLUG_1 when installing multiple display cards to provide sufficient power supply. Connect a 4-pin power cable to EZ_PLUG_2 to provide a stable power supply to the back IO ports. Thermal sensor cable connectors (2-pin OPT_TEMP1/2/3) These connectors are for temperature monitoring.
13. DirectKey connector (2-pin DRCT) This connector is for the chassis-mounted button that supports the DirectKey function. Connect the button cable that supports DirectKey, from the chassis to this connector on the motherboard. Ensure that your chassis comes with the extra button cable that supports the DirectKey feature. Refer to the technical documentation that came with the chassis for details.
ROG Extension - OC Panel connector (18-1 pin ROG_EXT) This connector is for the OC Panel. The OC Panel allows you to perform overclocking without going to the BIOS settings, loading the OS, or using overclocking software utilities.
1.2.10 ProbeIt The ROG ProbeIt allows you to detect your system’s current voltage and OC settings. Use a multimeter to measure the ProbeIt points even during overclocking. See the illustration below to locate the respective ProbeIt points. Using ProbeIt You may connect the multitester to the motherboard as shown on the following figure. Chapter 1 The photos above are for reference only, the actual motherboard layout and measure points location may differ by models.
Chapter 2: Basic Installation Basic Installation 2.1 Building your PC system 2.1.1 Motherboard installation 2 The diagrams in this section are for reference only. The motherboard layout may vary with models, but the installation steps are the same for all models. Install the ASUS Q-Shield to the chassis rear I/O panel. 2. Place the motherboard into the chassis, ensuring that its rear I/O ports are aligned to the chassis’ rear I/O panel. Chapter 2 1.
3. Place nine screws into the holes indicated by circles to secure the motherboard to the chassis. Chapter 2 DO NOT overtighten the screws! Doing so can damage the motherboard.
2.1.2 CPU installation Ensure that you install the correct CPU designed for LGA1150 socket only. DO NOT install a CPU designed for LGA1155 and LGA1156 sockets on the LGA1150 socket.
2.1.3 CPU heatsink and fan assembly installation Apply the Thermal Interface Material to the CPU heatsink and CPU before you install the heatsink and fan if necessary.
To uninstall the CPU heatsink and fan assembly 1 2 A B B Chapter 2 A ASUS MAXIMUS VI EXTREME 2-5
2.1.
2.1.
2.1.
2.1.7 Front I/O Connector To install ASUS Q-Connector 2 1 To install USB 2.0 connector To install front panel audio connector AAFP USB 2.0 Chapter 2 To install USB 3.0 connector USB 3.
2.1.
2.1.9 mPCIe Combo II installation ROG mPCIe Combo II offers expandability solutions with the latest connectivity standards via the proprietary connector onboard. It provides your system with the fastest Wi-Fi 802.11ac and Bluetooth 4.0 connection. It also features the M.2 (NGFF) slot for installing smaller SSDs. • The mPCIe Combo II card supports 26.8mm x 30mm half-sized mPCIe module on one side and M.2 (NGFF) Type 2242 SSD card (22mm x 42mm) SSD on the other side. • The M.
4. Replace the metal cover and secure the back of the metal cover with the two short screws that you removed in step 1. 5. Secure the front of the metal cover with the long screw that you removed in step 2. Installing the mPCIe Combo II card To install the mPCIe Combo II card to your motherboard: 1. Remove the black screw near the 36-2 pin connector. 2. Locate the MPCIE_COMBO_II connector on the motherboard then align and insert the mPCIe Combo II card to the MPCIE_COMBO_II connector.
3. Secure the mPCIe Combo II card either to the motherboard or the rear I/O shield using the black screw that you removed in step 1.
Installing the Wi-Fi antenna connector If you installed a Wi-Fi module on the mPCIe Combo II, you would need to install the Wi-Fi antenna connector. The Wi-Fi antenna and its cables are purchased separately. To install the Wi-Fi antenna connector: 1. Remove the bolt from the Wi-Fi antenna connector but leave the washer on the connector. washer bolt bolt washer 2. Insert the connector into the I/O shield’s Wi-Fi port hole. 3.
2.2 BIOS update utility USB BIOS Flashback USB BIOS Flashback allows you to easily update the BIOS without entering the existing BIOS or operating system. Simply insert a USB storage device to the USB port, press the USB BIOS Flashback button for three seconds, and the BIOS is updated automatically. To use USB BIOS Flashback: 1. Download the latest BIOS file from the ASUS website 2. Extract and rename the BIOS image file to M6E.CAP. 3. Copy M6E.CAP to the root directory of the USB flash disk drive.
2.3 Motherboard rear and audio connections 2.3.1 Rear I/O connection Rear panel connectors 1. BIOS Flashback button 2. USB 2.0 port 7 and 8. The ROG Connect port is the port on top. It supports USB BIOS Flashback and USB Charger+ 3. LAN (RJ-45) port* 4. Optical S/PDIF OUT port 5. PS/2 Keyboard/Mouse combo port 6. ROG Connect button 7. ASMedia USB 3.0 port E3 and E4, support ASUS USB 3.0 Boost Turbo Mode Chapter 2 8. USB 3.0 port E1 and E2, support ASUS USB 3.0 Boost Turbo Mode 9. HDMI port 10.
• Due to USB 3.0 controller limitation, USB 3.0 devices can only be used under Windows® OS environment and after the USB 3.0 driver installation. • USB 3.0 devices can only be used as data storage only. • We strongly recommend that you connect USB 3.0 devices to USB 3.0 ports for faster and better performance for your USB 3.0 devices. • Due to the design of the Intel® 8 series chipset, all USB devices connected to the USB 2.0 and USB 3.0 ports are controlled by the xHCI controller.
Connect to Headphone and Mic Connect to Stereo Speakers Connect to 2.
Connect to 4.1 channel Speakers Chapter 2 Connect to 5.
Connect to 7.
2.4 OC Panel The OC Panel is a device that allows you to perform overclocking without the need to go to the BIOS settings or use software utilities. You can setup the OC Panel in an available 5.25inch drive bay on your computer chassis (Normal Mode) or as an external handheld console on an “open-air” OC test bench (Extreme Mode.) These modes are further explained in the succeeding subsections. 2.4.1 • The FanSpeed Control button in Normal Mode supports the 4-pin CPU fan only.
OC Panel LCM Display in Normal Mode OC Panel LCM Display in Extreme Mode Chapter 2 2-22 Chapter 2: Basic Installation
2.4.2 Setting up your OC Panel in Normal Mode The OC Panel in Normal Mode mainly provides easy access buttons for increasing your CPU’s frequency level, adjusting fan speeds and customizing overclocking profiles. It also displays vital information about your computer’s CPU temperature, base clocks, and CPU fan speed (RPM). 2. Get the bundled OC Panel 5.25-inch drive bay metal case and set of two (2) screws. 3. Align and insert the OC Panel into the OC Panel 5.25-inch drive bay metal case.
4. Secure the OC Panel to the OC Panel 5.25-inch drive bay metal case with the two (2) screws. Ensure that the OC Panel fits snugly into the OC Panel 5.25-inch drive bay metal case. Chapter 2 2-24 5. Shut down your computer. 6. Open your computer chassis and remove the front cover of an available 5.25-inch drive bay. 7. Align and insert the OC Panel and the OC Panel 5.25-inch drive bay metal case assembly into the drive bay. 8. Secure the OC Panel and the OC Panel 5.
2.4.3 Setting up your OC Panel in Extreme Mode The OC Panel in Extreme Mode is setup with an open chassis system or “open-air” OC test bed assembly and enjoyed as a handheld console to perform overclocking and voltage tuning. When in Extreme Mode, you can enjoy more features including Subzero Sense and VGA Hotwire. It also comes with some of the most commonly used voltage tuning presets that are preconfigured for your convenience and optimum overclocking experience.
2.5 Starting up for the first time 1. After making all the connections, replace the system case cover. 2. Ensure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: 6. a. Monitor b. External SCSI devices (starting with the last device on the chain) c.
Chapter 3: BIOS setup BIOS setup 3.1 Knowing BIOS 3 The new ASUS UEFI BIOS is a Unified Extensible Interface that complies with UEFI architecture, offering a user-friendly interface that goes beyond the traditional keyboardonly BIOS controls to enable a more flexible and convenient mouse input. You can easily navigate the new UEFI BIOS with the same smoothness as your operating system. The term “BIOS” in this user manual refers to “UEFI BIOS” unless otherwise specified.
3.2 BIOS setup program Use the BIOS Setup to update the BIOS or configure its parameters. The BIOS screen include navigation keys and brief onscreen help to guide you in using the BIOS Setup program. Entering BIOS at startup To enter BIOS Setup at startup, press during the Power-On Self Test (POST). If you do not press , POST continues with its routines. Entering BIOS Setup after POST To enter BIOS Setup after POST: • Press ++ simultaneously.
3.2.1 EZ Mode The EZ Mode provides you an overview of the basic system information, and allows you to select the display language, system performance mode and boot device priority. To access the Advanced Mode, click Exit/Advanced Mode, then select Advanced Mode or press hot key for the advanced BIOS settings. The default screen for entering the BIOS setup program can be changed. Refer to the Setup Mode item in section 3.7 Boot menu for details.
3.2.2 Advanced Mode The Advanced Mode provides advanced options for experienced end-users to configure the BIOS settings. The figure below shows an example of the Advanced Mode. Refer to the following sections for the detailed configurations. To access the Advanced Mode, click Exit, then select Advanced Mode or press F7 hotkey.
Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting Main shows the Main menu items. The other items (My Favorites, Ai Tweaker, Advanced, Monitor, Boot, Tool, and Exit) on the menu bar have their respective menu items. Back button This button appears when entering a submenu. Press or use the USB mouse to click this button to return to the previous menu screen.
Last Modified button This button shows the items that you last modified and saved in BIOS Setup. 3.3 My Favorites MyFavorites is your personal space where you can easily save and access your favorite BIOS items. Adding items to My Favorites To add frequently-used BIOS items to My Favorites: 1. Use the arrow keys to select an item that you want to add. When using a mouse, hover the pointer to the item. 2. Press on your keyboard or right-click on your mouse to add the item to My Favorites page.
3.4 Extreme Tweaker menu The Extreme Tweaker menu items allow you to configure overclocking-related items. Be cautious when changing the settings of the Extreme Tweaker menu items. Incorrect field values can cause the system to malfunction. The configuration options for this section vary depending on the CPU and DIMM model you installed on the motherboard. Chapter 3 Scroll down to display other BIOS items.
Ai Overclock Tuner [Auto] Allows you to select the CPU overclocking options to achieve the desired CPU internal frequency. Select any of these preset overclocking configuration options: [Auto] Loads the optimal settings for the system. [X.M.P.] If you install memory modules supporting the eXtreme Memory Profile (X.M.P.) Technology, choose this item to set the profiles supported by your memory modules for optimizing the system performance.
When the CPU Core Ratio is set to [Synch All Cores], the following item appears. 1-Core Ratio Limit [Auto] Allows you to set the 1-Core Ratio Limit. [Auto] Select to apply the CPU default Turbo Ratio setting. [Manual] Select to manually assign a 1-Core Ratio Limit value that is higher than or equal to the 2-Core Ratio Limit. Min CPU Cache Ratio [Auto] Allows you to set the uncore ratio of the processor to its possible minimum value.
Internal PLL Overvoltage [Auto] Allows you to enable the internal PLL voltage for K-SKU CPUs to get the extreme overclocking capability. Configuration options: [Auto] [Enabled] [Disabled] CPU bus speed : DRAM speed ratio mode [Auto] Allows you to set the CPU bus speed to DRAM speed ratio mode. [Auto] The DRAM speed is set to its optimized settings. [100:133] The CPU bus speed to DRAM speed ratio is set to 100:133. [100:100] The CPU bus speed to DRAM speed ratio is set to 100:100.
Changing the values in this menu may cause the system to become unstable! If this happens, revert to the default settings.
RTL IOL control DRAM RTL (CHA_R0D0) [Auto] Configuration options: [Auto] [1] - [63] DRAM RTL (CHA_R0D1) [Auto] Configuration options: [Auto] [1] - [63] DRAM RTL (CHA_R1D0) [Auto] Configuration options: [Auto] [1] - [63] DRAM RTL (CHA_R1D1) [Auto] Configuration options: [Auto] [1] - [63] DRAM RTL (CHB_R0D0) [Auto] Configuration options: [Auto] [1] - [63] DRAM RTL (CHB_R0D1) [Auto] Configuration options: [Auto] [1] - [63] DRAM RTL (CHB_R1D0) [Auto] Configuration options: [Auto] [1] - [63] DRAM RTL (CHB_R1D1)
tWRRD_dr [Auto] Configuration options: [Auto] [1] – [15] tWRRD_dd [Auto] Configuration options: [Auto] [1] – [15] tWRWR [Auto] Configuration options: [Auto] [1] – [7] tWRWR_dr [Auto] Configuration options: [Auto] [1] – [15] tWRWR_dd [Auto] Configuration options: [Auto] [1] – [15] Dec_WRD Configuration options: [Auto] [0] – [1] tRDWR [Auto] Configuration options: [Auto] [1] – [31] tRDWR_dr [Auto] Configuration options: [Auto] [1] – [31] tRDWR_dd [Auto] Configuration options: [Auto] [1] – [31] MISC M
DQ Sense Amplifier [Auto] Reducing usually helps overclocking and over-voltage. Configuration options: [Auto] [+16] – [-16] DQS Sense Amplifier [Auto] Reducing usually helps overclocking and over-voltage. Configuration options: [Auto] [+16] – [-16] CMD Sense Amplifier [Auto] Reducing usually helps overclocking and over-voltage. Configuration options: [Auto] [+16] – [-16] DRAM Swizzling Bit 0 [Auto] Enabling usually helps overclocking.
DIGI+ Power Control CPU Load-Line Calibration [Auto] Load-line is defined by Intel® VRM specification and affects CPU power voltage. The CPU working voltage will decrease proportionally to CPU loading. Higher load-line calibration could get higher voltage and good overclocking performance but increases the CPU and VRM thermal conditions. Select from Level 1 to Level 8 to adjust CPU power voltage from 0% to 100%. • The actual performance boost may vary depending on your CPU specification.
CPU Power Phase Control [Standard] Allows you to set the power phase control of the CPU. [Standard] Set the phase control based on the CPU command. [Optimized] Set the ASUS optimized phase tuning profile. [Extreme] Set the full phase mode [Manual Adjustment] Set manually to a faster phase response to increase system performance or to slower phase response to increase DRAM power efficiency. DO NOT remove the thermal module when setting this item to [Extreme] and [Manual Adjustment].
CPU Power Thermal Control [130] A higher temperature brings a wider CPU power thermal range and extends the overclocking tolerance to enlarge the O.C. potential. Use the <+> and <-> keys to adjust the value. The values range from 130 to 151. DO NOT remove the thermal module. The thermal conditions should be monitored. CPU Input Boot Voltage [Auto] VCCIN for the CPU right at boot. Configuration options: [Auto] [0.800] – [2.
Tweakers’ Paradise The subitems in this menu allow you to set the CPU ratio and features. VCCIN Shadow Voltage [Auto] Pseudo Voltage for VCCIN. Configuration options: [Auto] [0.800] – [2.440V] Termination Anti-Aliasing [Auto] Termination Anti-Aliasing. Configuration options: [Auto] [Disabled] [Enabled] Initial PLL Termination Voltage [Auto] Initial Voltage at which CPU BCLKs are terminated. Maintaining a level close to CPU Input Voltage will help BCLK Overclock. Configuration options: [Auto] [0.
DMI Gen 2 [Auto] Allows you to enable or disable DMI Gen 2. Auto means Enabled. Configuration options: [Auto] [Enabled] [Disabled] DMI De-emphasis Control [-6 dB] Configure De-emphasis control on DMI. Configuration options: [-6 dB] [-3.5 db] SATA Drive Strength [Auto] SATA Drive Strength. Configuration options: [Auto] [+10] - [-10] CPU PCIE Controller [Enabled] CPU PCIE Controller.
CPU Power Management The subitems in this menu allow you to set the CPU ratio and features. Enhanced Intel SpeedStep Technology [Enabled] Allows the operating system to dynamically adjust the processor voltage and cores frequency to decrease the average power consumption and decrease average heat production.
CPU Internal Power Configuration CPU Integrated VR Efficiency Management [Auto] Allows you to improve power saving when the processor is in low power state. Disable this item to make the Fully Integrated Voltage Regulator work in high performance at all times. Configuration options: [Auto] [High Performance] [Balanced] Power Decay Mode [Auto] Allows you to enable this item to improve the power saving on the Fully Integrated Voltage Regulator as the processor goes into low current state.
3.5 Main menu The Main menu screen appears when you enter the Advanced Mode of the BIOS Setup program. The Main menu provides you an overview of the basic system information, and allows you to set the system date, time, language, and security settings. Security The Security menu items allow you to change the system security settings. Chapter 3 3-22 • If you have forgotten your BIOS password, erase the CMOS Real Time Clock (RTC) RAM to clear the BIOS password. See section 1.2.
Administrator Password If you have set an administrator password, we recommend that you enter the administrator password for accessing the system. Otherwise, you might be able to see or change only selected fields in the BIOS setup program. To set an administrator password: 1. Select the Administrator Password item and press . 2. From the Create New Password box, key in a password, then press . 3. Confirm the password when prompted. To change an administrator password: 1.
To change a user password: 1. Select the User Password item and press . 2. From the Enter Current Password box, key in the current password, then press . 3. From the Create New Password box, key in a new password, then press . 4. Confirm the password when prompted. To clear the user password, follow the same steps as in changing a user password, but press when prompted to create/confirm the password.
3.6 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Chapter 3 Be cautious when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction.
3.6.1 CPU Configuration The items in this menu show the CPU-related information that the BIOS automatically detects. The items in this menu may vary based on the CPU installed. Intel Adaptive Thermal Monitor [Enabled] [Enabled] [Disabled] Enables the overheated CPU to throttle its clock speed to cool down. Disables the CPU thermal monitor function.
Execute Disable Bit [Enabled] [Enabled] [Disabled] Enables the No-Execution Page Protection Technology. Forces the XD feature flag to always return to zero (0). Intel® Virtualization Technology [Disabled] [Enabled] [Disabled] Allows a hardware platform to run multiple operating systems separately and simultaneously, enabling one system to virtually function as several systems. Disables this function.
CPU C States [Auto] Allows you to enable or disable the CPU C states. Configuration options: [Auto] [Enabled] [Disabled] The following items appear only when you set the CPU C States to [Enabled]. Enhanced C1 state [Enabled] Allows your processor to reduce power when the system is in idle mode. Configuration options: [Enabled] [Disabled] CPU C3 Report [Enabled] Allows you to disable or enable the CPU C3 report to the operating system.
3.6.2 PCH Configuration PCI Express Configuration Allows you to configure the PCI Express slots. DMI Link ASPM Control [Auto] Allows you to control the ASPM (Active State Power Management) on both Northbridge side and Southbridge side of the DMI Link. Configuration options: []Auto] [Disabled] [Enabled] ASPM Support [Disabled] Allows you to set the ASPM level. Configuration options: [Disabled] [Auto] [L0s] [L1] [L0sL1] PCIe Speed [Auto] Chapter 3 Allows you to select the PCI Express port speed.
Intel®Rapid Start Technology [Disabled] Allows you to enable or disable Intel Rapid Start Technology. Configuration options: [Enabled] [Disabled] The following items appear only when you set the Intel® Rapid Start Technology to [Enabled]. Entry on S3 RTC Wake [Enabled] The system automatically wakes up and set to Rapid Start Technology S4 mode. Configuration options: [Enabled] [Disabled Entry After [0] This item appears only when you set the Entry on S3 RTC Wake to [Enabled].
3.6.3 SATA Configuration While entering Setup, the BIOS automatically detects the presence of SATA devices. The SATA Port items show Empty if no SATA device is installed to the corresponding SATA port. Scroll down to display the other BIOS items. SATA Mode Selection [AHCI] Allows you to set the SATA configuration. [IDE] [AHCI] [RAID] Disables the SATA function. Set to [IDE] when you want to use the Serial ATA hard disk drives as Parallel ATA physical storage devices.
S.M.A.R.T. Status Check [Enabled] S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitor system. When read/write of your hard disk errors occur, this feature allows the hard disk to report warning messages during the POST. Configuration options: [Enabled] [Disabled] Hot Plug [Disabled] (SATA6G_1 - SATA6G_6 [Red]) These items appear only when you set the SATA Mode Selection item to [AHCI] or [RAID], and allow you to enable/disable SATA Hot Plug Support.
Render Standby [Auto] Allows you to enable the Intel® Graphics Render Standby support to reduce iGPU power use when the system is idle. Configuration options: [Auto] [Disabled] [Enabled] iGPU Multi-Monitor [Disabled] Allows you to enable both integrated and discrete graphics for multi-monitor output. The iGPU shared system memory size will be fixed at 64MB. Configuration options: [Disabled] [Enabled] DMI Configuration Allows you to control various DMI (Desktop Management Interface) functions.
3.6.5 USB Configuration The items in this menu allow you to change the USB-related features. The USB Devices item shows the auto-detected values. If no USB device is detected, the item shows None. Legacy USB Support [Enabled] [Enabled] [Disabled] [Auto] Enables the support for USB devices on legacy operating systems (OS). The USB devices can be used only for the BIOS setup program. It cannot be recognized in boot devices list. Allows the system to detect the presence of USB devices at startup.
3.6.6 Platform Misc Configuration The items in this menu allow you to configure the platform-related features. PCI Express Native Power Management [Disabled] Allows you to enhance the power saving feature of PCI Express and perform ASPM operations in the operating system. Configuration options: [Disabled] [Enabled] The following item appears only when you set the PCI Express Native Power Management to [Enabled]. Native ASPM [Disabled] [Enabled] Vista controls the ASPM support for the device.
3.6.7 Onboard Devices Configuration Scroll down to view the other BIOS items. HD Audio Controller [Enabled] [Enabled] Enables the High Definition Audio Controller. [Disabled] Disables the controller. The following items appear only when you set the HD Audio Controller to [Enabled]. Front Panel Type [HD] Allows you to set the front panel audio connector (AAFP) mode to legacy AC’97 or high-definition audio depending on the audio standard that the front panel audio module supports.
Bluetooth Controller [Enabled] Allows you to enable or disable the Bluetooth controller. Configuration options: [Enabled] [Disabled] Wi-Fi Controller [Enabled] Allows you to enable or disable the Wi-Fi controller. Configuration options: [Enabled] [Disabled] mPCIe Combo II NGFF [Auto] Allows you to enable or disable the support to mPCIe Combo II NGFF.
3.6.8 APM ErP Ready [Disabled] Allows you to switch off some power at S4+S5 or S5 to get the system ready for ErP requirement. When set to [Enabled], all other PME options will be switched off. Configuration options: [Disabled] [Enabled (S4+S5] [Enabled (S5)] Restore AC Power Loss [Power Off] [Power On] The system goes into ON state after an AC power loss. [Last State] The system goes into either OFF or ON state, whatever the system state was before the AC power loss.
3.6.9 Network Stack Network Stack [Disabled] This item allows you to disable or enable the UEFI network stack. Configuration options: [Disabled] [Enable] The following items appear only when you set the Network Stack to [Enabled]. Ipv4/Ipv6 PXE Support [Enabled] Allows you to enable or disable the Ipv4/Ipv6 PXE boot option. Configuration options: [Disabled] [Enabled] 3.5.10 LED Control Chapter 3 Onboard LED [Enabled] This item allows you to disable or enable the onboard LEDs.
3.7 Monitor menu The Monitor menu displays the system temperature/power status, and allows you to change the fan settings. Anti Surge Support [Enabled] This item allows you to enable or disable the Anti Surge function. Configuration options: [Disabled] [Enabled] Voltage Monitor CPU Core 0-3 Voltage; CPU Cache Voltage; CPU System Agent Voltage; CPU Analog I/O Voltage; CPU Digital I/O Voltage; CPU Input Voltage; DRAM Voltage; PCH Voltage; 3.
Fan Speed Control CPU Q-Fan Control [Enabled] [Disabled] Disables the CPU Q-Fan control feature. [Auto Detect] Enables the CPU Q-Fan control feature. [PWM Mode] Enables the CPU Q-Fan control feature. The following items appear only when you set the CPU Q-Fan Control to [PWM Mode] and [Auto Detect]. CPU Fan Speed Low Limit [600 RPM] Allows you to disable or set the CPU fan warning speed.
Chassis Q-Fan Control 1-3 [Disabled] [Disabled] Disables the Chassis Q-Fan control feature. [Enabled] Enables the Chassis Q-Fan control feature. Chassis Fan Speed Low Limit 1-3 [600 RPM] This item appears only when you enable the Chassis Q-Fan Control feature and allows you to disable or set the chassis fan warning speed.
The following four items appear only when you set OPTFAN 1/2/3 to [Profile Model]. OPT Fan 1/2/3 Profile Allows you to set the optional fans’ profiles. Configuration options: [Performance] [Optional] [Silent] Profile Mode Allows you to set the optional fans’ profiles. Configuration options: [Performance] [Optional] [Silent] User Mode Allows you to set the optional fan’s speed temperature. OPT1-3 Low Speed Temp [25%] Allows you to set the optional fans’ low speed temperature.
3.8 Boot menu The Boot menu items allow you to change the system boot options. Scroll down to display the other BIOS items. Boot Configuration Fast Boot [Disabled] [Disabled] Allows your system to go back to its normal boot speed. [Enabled] Allows your system to accelerate the boot speed. The following items appear only when you set the Fast Boot to [Enabled]. USB Support [Partial In...] Chapter 3 [Disabled] All USB devices will not be available until OS boot up for a fastest POST time.
Network Stack Driver Support [Disabled] [Disabled] Select to skip the network stack driver from loading during POST. [Enabled] Select to load the network stack driver during POST. Next Boot after AC Power Loss [Normal Boot] [Normal Boot] [Fast Boot] Returns to normal boot on the next boot after an AC power loss. Accelerates the boot speed on the next boot after an AC power loss. HW Fast Boot [Disabled] Allows the system to enable or disable the HW Fast Boot.
Option ROM Messages [Force BIOS] [Force BIOS] [Keep Current] The third-party ROM messages will be forced to display during the boot sequence. The third-party ROM messages will be displayed only if the third-party manufacturer had set the add-on device to do so. Interrupt 19 Capture [Enabled] When set to [Enabled], allows the option ROMs to trap Interrupt 19.
Secure Boot Allows you to configure the Windows® Secure Boot settings and manage its keys to protect the system from unauthorized access and malwares during POST. OS Type [Windows UEFI mode] [Windows UEFI Mode] Allows you to select your installed operating system. Execute the Microsoft® Secure Boot check. Only select this option when booting on Windows® UEFI mode or other Microsoft® Secure Boot compliant OS.
3.9 Tools menu 3.9.1 ASUS EZ Flash 2 Utility The Tools menu items allow you to configure options for special functions. Select an item then press to display the submenu. Allows you to run ASUS EZ Flash 2. When you press , a confirmation message appears. Use the left/right arrow key to select between [Yes] or [No], then press to confirm your choice. For more details, refer to section 3.11.2 ASUS EZ Flash 2 utility. 3.9.2 ASUS O.C.
Label Allows you to input the label of the setup profiles. Save to Profile Allows you to save the current BIOS settings to the BIOS Flash, and create a profile. Key in a profile number from one to eight, press , and then select Yes. Load from Profile Allows you to load the previous BIOS settings saved in the BIOS Flash. Key in the profile number that saved your BIOS settings, press , and then select Yes. 3.9.
3.9.4 BIOS Flashback Allows you select copy and boot from either BIOS1 or BIOS2. Force BIOS2 Boot Select [Yes] to force the boot using BIOS2. COPY BIOS1 to BIOS2 [Yes] Select [Yes] to copy the content of BIOS1 to BIOS2. Only the current operating System will enter the soft-off state. After BIOS backup is finished, the system will auto power-on.
3.10 Exit menu The Exit menu items allow you to load the optimal default values for the BIOS items, and save or discard your changes to the BIOS items. You can access the EZ Mode from the Exit menu. Load Optimized Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press , a confirmation window appears. Select Yes to load the default values.
3.11 Updating BIOS The ASUS website publishes the latest BIOS versions to provide enhancements on system stability, compatibility, or performance. However, BIOS updating is potentially risky. If there is no problem using the current version of BIOS, DO NOT manually update the BIOS. Inappropriate BIOS updating may result in the system’s failure to boot. Carefully follow the instructions of this chapter to update your BIOS if necessary. Visit the ASUS website at www.asus.
3.11.1 ASUS EZ Flash 2 ASUS EZ Flash 2 allows you to update the BIOS without having to use a bootable floppy disk or an OS‑based utility. Before you start using this utility, download the latest BIOS from the ASUS website at www.asus.com. 1. Insert the USB flash disk that contains the latest BIOS file to the USB port. 2. Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select ASUS EZ Flash Utility and press to enable it. 3. Press to switch to the Drive field.
• This function can support devices such as a USB flash disk with FAT 32/16 format and single partition only. • DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure! Ensure to load the BIOS default settings to ensure system compatibility and stability. Select the Load Optimized Defaults item under the Exit menu. See section 3.9 Exit Menu for details. 3.11.
3.11.3 ASUS BIOS Updater The ASUS BIOS Updater allows you to update the BIOS in DOS environment. This utility also allows you to copy the current BIOS file that you can use as a backup when the BIOS fails or gets corrupted during the updating process. The succeeding utility screens are for reference only. The actual utility screen displays may not be same as shown. Before updating BIOS 1. Prepare the motherboard support DVD and a USB flash drive in FAT32/16 format and single partition. 2.
3. When the Make Disk menu appears, select the FreeDOS command prompt item by pressing the item number. 4. At the FreeDOS prompt, type d: and press to switch the disk from Drive C (optical drive) to Drive D (USB flash drive). Welcome to FreeDOS (http://www.freedos.org)! C:\>d: D:\> Updating the BIOS file To update the BIOS file using BIOS Updater: 1. At the FreeDOS prompt, type bupdater /pc /g and press . D:\>bupdater /pc /g 2. The BIOS Updater screen appears as below.
4. Select Yes and press . When BIOS update is done, press to exit BIOS Updater. Restart your computer. DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure! For BIOS Updater version 1.04 or later, the utility automatically exits to the DOS prompt after updating BIOS. • Ensure to load the BIOS default settings to ensure system compatibility and stability. Select the Load Optimized Defaults item under the Exit BIOS menu.
3.12 Secure Erase SSD speeds may lower over time as with any storage medium due to data processing. Secure Erase completely and safely cleans your SSD, restoring it to factory performance performance levels. Secure Erase is only available in AHCI mode. Ensure to set the SATA mode to AHCI. Click Advanced > SATA Configuration > AHCI. To launch ROG SSD Secure Erase, click Tool > ROG SSD Secure Erase on the Advanced mode menu. Check the ASUS support site for a full list of SSDs tested with Secure Erase.
Chapter 4: Software support Software support 4.1 Installing an operating system 4.2 4 • This motherboard supports Windows® 8 32/64-bit and Windows® 7 32/64-bit operating systems (OS). • Motherboard settings and hardware options vary. Use the setup procedures presented in this chapter for reference only. Refer to your OS documentation for detailed information. Support DVD information The contents of the support DVD are subject to change at any time without notice. Visit the ASUS website at www.
Support DVD main menu The Drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to use the devices. The Utilities menu shows the applications and other software that the motherboard supports. The Manual menu contains the list of supplementary user manuals. Click an item to open the folder of the user manual. The Video menu contains ROG related videos. Click the Contact tab to display the ASUS contact information.
4.2.2 Obtaining the software manuals The software manuals are included in the support DVD. Follow the instructions below to get the necessary software manuals. The software manual files are in Portable Document Format (PDF). Install the Adobe® Acrobat® Reader from the Utilities tab before opening the files. 1. Click Manual tab > ASUS Motherboard Utility Guide. 2. From the Manual folder, open the folder of the software manual that you wish to read. 3.
4.3 Software information 4.4 AI Suite 3 Most of the applications in the support DVD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software application for more information. AI Suite 3 is an all-in-one interface that integrates several ASUS utilities and allows you to launch and operate these utilities simultaneously.
Windows® 8 OS 1. Place the Support DVD into the optical drive then follow onscreen instructions. 2. From the ASUS motherboard support DVD main menu, select the Utilities tab and click AI Suite 3. 3. Follow the succeeding onscreen instructions. If the ASUS motherboard support DVD main menu did not appear, try the following steps: a. Go to the Start Screen then click or tap the Desktop app. b.
AI Suite 3 Main menu The AI Suite 3 main menu gives you easy-access controls and insight to what’s going on with your computer - allowing you to optimize performance settings while at the same time ensuring system stability. Included in the AI Suite 3 main menu is a quick-access menu bar that allows you to swiftly launch any of the integrated ASUS utilities. Click or tap the on the top-edge of menu to launch the menu bar.
4.4.1 Dual Intelligent Processors 4 Dual Intelligent Processors 4 comes with these five utilities in one interface: 4-Way Optimization, TurboV Processing Unit (TPU), Energy Processing Unit (EPU), DIGI+ Power Control, and Fan Xpert 2. 4-Way Optimization The 4-Way Optimization utility allows you to automatically tweak the TPU, EPU, DIGI + Power Control and Fan Xpert 2 to their optimal settings.
TurboV Processing Unit (TPU) ASUS TPU allows you to manually adjust the CPU frequency, CPU Cache and Core frequencies, DRAM frequency, and related voltages for an enhanced system stability and boost performance. Refer to the CPU documentation before adjusting CPU voltage settings. Setting a high voltage may damage the CPU permanently, and setting a low voltage may lead to an unstable system.
Voltage Drag to adjust CPU Core Voltage offset Drag to adjust CPU Cache Voltage offset Click to apply the adjustments Click to save the adjustment into a profile Click to load the saved profile Drag the slider to adjust DRAM, CPU Analog I/O, PCH, and CPU Input voltages Click to undo the adjustments Drag the slider to adjust CPU System Agent, CPU Digital I/O, VTTDDR, and PCHVLX voltages GPU Boost Drag to adjust the iGPU Max Voltage Click or to adjust the CPU VCCSA voltage Click to enable the Click t
Energy Processing Unit (EPU) EPU is an enery-processing utility that allows you to adjust the CPU, GPU, and Fan Control settings to their power-saving conditions.
DIGI+ Power Control DIGI+ Power Control allows you to adjust the VRM voltage and frequency for optimal system efficiency, overall system stability and performance. CPU Power You can configure the following CPU Power items: • • • • • CPU Power Duty Control CPU Power Duty Control adjusts the current of every VRM phase and the thermal conditions of every phase component. CPU Load-line Calibration CPU Load-line Calibration adjusts the voltage range and controls the system temperature.
Fan Xpert 2 Fan Xpert 2 automatically detects and tweaks the fan speeds, and provides you with optimized fan settings based on the fans’ specifications and positions.
RPM Mode RPM Mode allows you to set the fan speed when the CPU temperature is below 75oC. Click and drag to adjust the fan’s speed Click to go back to the previous screen Click to switch between the CPU and chassis fan screens Click to undo the changes Click to apply the changes • When the CPU temperature reaches 75o C, the fan will automatically run at full speed to protect the CPU. • For motherboard models without the CPU fan detection latch, only 4-pin CPU fans are controllable in Fan Xpert 2.
4.4.2 Wi-Fi GO! Wi-Fi GO! is an ASUS-exclusive Wi-Fi utility that allows you to wirelessly stream your media files to DLNA devices, control your computer using your smart device, transfer files to your smart device, and provides access to your files stored in your cloud storage. System requirements System requirements PC Smart device OS Windows® 7/Windows® 8 Android 2.
Using Wi-Fi GO! To use Wi-Fi GO!, click or tap the select Wi-Fi GO! . on the top edge of the AI Suite 3 main menu, then Click to set a password Use your smart device to scan QR Codes for more information Wi-Fi GO! menu • Launch Wi-Fi GO! & NFC Remote on your smart device to use the Wi-Fi GO! & NFC remote control functions. For more details, refer to section Wi-Fi GO! & NFC Remote of this user manual for more details. • To protect your Wi-Fi utility from unauthorized remote access, click password.
Using the Wake-on-LAN If you want to wake up your computer using the smart device, ensure that you enable the computer’s Wake-on-LAN settings. To configure your computer’s Wake-on-LAN settings: 1. From BIOS Setup, go to Advanced > APM then set Power On By PCIE/PCI item to [Enabled]. 2. From Windows® OS, do the following: a. On your desktop, click Start, right-click Computer > Manage to launch the Computer Management screen. b. Click Device Manager to view all the installed devices. c.
Using Cloud GO! 1. On your computer, click Cloud GO! on the Wi-Fi GO! screen. 2. Click Enter to access your cloud storage accounts. 3. Log into your Asus WebStorage, Google Drive™ or Dropbox® cloud account then click Sign In.
Using DLNA Media Hub To stream media files to a DLNA display, enable the remote control functions in your Windows Media Player. To do this, launch Windows Media Player, click Stream then tick Allow remote control of my Player and Automatically allow devices to play my media. Using DLNA Media Hub on the computer On your computer, click DLNA Media Hub then click Enter.
Using File Transfer Click to set a destination path for file transfers from smart device to computer Click to go back to Wi-Fi GO! window Click to go back to the previous screen Click to transfer files Transferring files from your computer to your smart device To transfer files from your computer to your smart device, right-click the file then click Send to > [Device name]. After the file transfer is complete, click OK.
Using Smart Sensor Control 1. On your computer, click Smart Sensor Control on the Wi-Fi GO! window. 2. Click Camera to take pictures or record videos. Ensure to enable the Smart Sensor Control on your smart device to enable the smart device’s camera. Click to record videos Click to take pictures Click to go back to Wi-Fi GO! window Click to go back to the previous screen The files are automatically saved in the smart device’s local storage.
Using Remote Keyboard & Mouse From your smart device, tap Remote Keyboard & Mouse then tap Enter. Tick to hold left click function Tap to set mouse sensitivity Input field Mouse tap area Control keys Tap to mimic right-click function Tap to mimic left-click function Tap to scroll up or down Using Capture & Send On your computer, click Capture & Send on the Wi-Fi GO! window.
4.4.3 Wi-Fi Engine To use Wi-Fi Engine, click or tap the select Wi-Fi Engine. on the top edge of the AI Suite 3 main menu, then Click to connect to a wireless access point Click to set up your computer as a wireless access point Using the Client Mode The Client mode allows you to connect your system to a wireless access point or a host router. To use the client mode: 1. On the Wi-Fi Engine menu, click Client Mode to launch Network Connections. 2.
Using the AP Mode The AP mode allows you to set your system as an access point for other wireless-enabled devices. To use AP mode, click AP Mode on the Wi-Fi Engine menu. Key in a network name Key in your password Key in your password for confirmation Click to go back to previous screen Click to select a network connection Click to disable AP mode Click to enable AP mode In this mode, the Internet Connection Sharing may depend on the Bluetooth/Internet device’s driver support.
4.4.4 EZ Update EZ Update is a utility that allows you to automatically update your motherboard’s softwares, drivers and the BIOS version easily. With this utlity, you can also manually update the BIOS and select the boot logo that will display during POST. Launching EZ Update To launch EZ Update, click or tap the select EZ Update.
4.4.5 USB 3.0 Boost USB 3.0 Boost technology supports UASP (USB Attached SCSI Protocol) that automatically speeds up the transfer rates of your USB storage devices. Launching USB 3.0 Boost To launch USB 3.0 Boost, click or tap the then select USB 3.0 Boost. on the top edge of the AI Suite 3 main menu, Using the USB 3.0 Boost 1. Connect your USB 3.0 device to the USB 3.0 port. 2. From the USB 3.0 Boost screen, select a USB device. 3. To enable UASP on your USB device, click UASP.
4.4.6 System Information This utility allows you get the detailed information of the motherboard, CPU, and memory settings. Launching the System Information To launch System Information, click or tap the menu, then select System Information. on the top edge of the AI Suite 3 main Viewing the motherboard information From the System Information screen, click MB tab to view the motherboard’s information.
Viewing the SPD information Chapter 4 From the System Information screen, click SPD tab to view the memory’s information.
4.4.7 USB BIOS Flashback Wizard USB BIOS Flashback Wizard allows you to check and save the latest BIOS version to a USB storage device. Use this utility to quickly check for the latest available BIOS and set the BIOS download schedule.
4.4.8 Ai Charger+ Ai Charger+ allows you to fast-charge your portable BC 1.1* mobile devices on your computer’s USB port three times faster than the standard USB devices**. Launching Ai Charger+ To launch Ai Charger+, click or tap the then select Ai Charger+. on the top edge of the AI Suite 3 main menu, Ai Charger+ screen Tick to enable or disable Ai Charger+ Tick to apply the selection * Check the manufacturer if your USB device is a Battery Charging Specification 1.1 (BC 1.
4.4.9 USB Charger+ USB Charger+ allows you to quick-charge your portable USB devices even if your computer is off, in sleep mode or hibernate mode. Before using USB Charger+, ensure to disable the ErP Ready item from the Advanced > APM > ErP Ready in the Advanced mode of the BIOS Setup program. Launching USB Charger+ To launch USB Charger+, click or tap the then select USB Charger+.
4.4.10 Audio configurations The Realtek® audio CODEC provides 8-channel audio capability to deliver the ultimate audio experience on your computer. The software provides Jack-Sensing function, S/PDIF Out support, and interrupt capability. The CODEC also includes the Realtek® proprietary UAJ® (Universal Audio Jack) technology for all audio ports, eliminating cable connection errors, and giving users plug and play convenience.
4.4.11 ROG Connect ROG Connect allows you to monitor and adjust the local PC through your remote PC. Setting up USB connection between your local and remote PC • Install ROG Connect on the remote PC from the provided Support DVD before using ROG Connect. • ROG Connect must work with ROG Connect Plus to avail full function. Ensure that you install ROG Connect Plus on your local PC from the provided Support DVD before using ROG Connect. 1.
2. Click Function to display more options. RC Poster RC Poster shows the status of the local system during the POST. You can switch the display mode between String and Code. RC Remote RC Remote allows you to operate your local system through the ROG Connect cable. RC Diagram Chapter 4 RC Diagram allows you to monitor and record your local system status.
GPU TweakIt GPU TweakIt allows you to control and monitor the installed GPU on the local system. Use the sliders to adjust the values and click Apply to save your customized settings. 4.4.12 MemTweakIt MemTweakIt allows you to adjust the timing of your installed memory. It also allows you to save, validate and post your configuration on the ROG website depending on your DRAM Efficency Score. To use MemTweakIt: on the desktop. 1. Double-click 2.
4. Click About tab and click REPUBLIC OF GAMERS to access ROG official website. 5. Click OK to exit MemTweakIt. Validating and saving your MemTweakIt settings To validate and save your configuration online: 1. Launch MemTweakIt and click Validate. 2. In Online Mode, key in your ASUS account ID and password, and click Submit. Your configuration will be displayed in MemTweakIt webpage. Click OK to close the Validation window. Chapter 4 3.
To validate and save your configuration manually: 1. Launch MemTweakIt and click Validate. 2. In Manual Mode, click Save Configuration File. 3. Key in a file name for your configuration file and click Save. 4. Click validation webpage. 5. In MemTweakIt - Validation File Upload window, key in your ASUS account ID and password. 6. Click Browse, locate the saved .cvf file, and click Open. 7. Click Submit. Your configuration will be displayed in MemTweakIt webpage.
4.4.13 RAMDisk RAMDisk is a data-storage software that reserves a part of your system’s memory and turns it into a high-speed virtual drive where you can store cache files and game apps for instant access. By optimizing your RAIDR Express card’s SSD, RAMDisk allows you to automatically backup, update, and restore files. The following folders are not suitable for RAMDisk optimization. Moving them into the RAMDisk might negatively affectm the performance of your system.
To delete an existing RAMDisk drive: Click to delete the existing RAMDisk drive. Creating/Deleting a Junction Point A junction point creates a link that remaps the original contents into the RAMDisk, enabling access to the desired application or data to be done purely within the original file location. Select the Junction tab to create your junction point Click the drop-down arrow to select your RAMDisk drive and its available storage space. Click to delete the existing junction point.
Synchronizing backup files After creating a junction point, RAMDisk automatically creates a backup folder in the file’s original location. Use RAMDisk to manually synchronize updates with these backup files.
Chapter 4 4-40 Chapter 4: Software support
Chapter 5: RAID support RAID support 5.1 RAID configurations 5 The motherboard comes with the Intel® Rapid Storage Technology that supports RAID 0, RAID 1, RAID 10 and RAID 5 configuration. If you want to install a Windows® operating system to a hard disk drive included in a RAID set, you have to create a RAID driver disk and load the RAID driver during OS installation. Refer to section 5.2 Creating a RAID driver disk for details. 5.1.
5.1.2 Installing Serial ATA hard disks The motherboard supports Serial ATA hard disk drives. For optimal performance, install identical drives of the same model and capacity when creating a disk array. To install the SATA hard disks for a RAID configuration: 1. Install the SATA hard disks into the drive bays. 2. Connect the SATA signal cables. 3. Connect a SATA power cable to the power connector on each drive. 5.1.
5.1.4 Intel® Rapid Storage Technology Option ROM utility To enter the Intel® Rapid Storage Technology Option ROM utility: 1. Turn on the system. 2. During POST, press + to display the utility main menu. Intel(R) Rapid Storage Technology - Option ROM - v10.5.1.1070 Copyright(C) 2003-10 Intel Corporation. All Rights Reserved. [ MAIN 1. Create RAID Volume 2. Delete RAID Volume 3. Reset Disks to Non-RAID RAID Volumes: None defined.
Creating a RAID set To create a RAID set: 1. From the utility main menu, select 1. Create RAID Volume and press . The following screen appears: Intel(R) Rapid Storage Technology - Option ROM - v10.5.1.1070 Copyright(C) 2003-10 Intel Corporation. All Rights Reserved. [ CREATE VOLUME MENU ] Name: Volume0 RAID Level: Disks: Strip Size: Capacity: Sync: Create volume [ HELP ] Enter a unique volume name that has no special characters and is 16 characters or less.
5. Use the up/down arrow key to select a drive, and then press to select. A small triangle marks the selected drive. Press after completing your selection. 6. Use the up/down arrow key to select the stripe size for the RAID array (for RAID 0, 10 and 5 only),and then press . The available stripe size values range from 4KB to 128KB.
Deleting a RAID set Be cautious when deleting a RAID set. You will lose all data on the hard disk drives when you delete a RAID set. To delete a RAID set: 1. From the utility main menu, select 2. Delete RAID Volume and press . The following screen appears: Name Volume0 [ DELETE VOLUME MENU ] Level Drives RAID0(Stripe) 2 Capacity 298.0GB Status Normal Bootable Yes [ HELP ] Deleting a volume will reset the disks to non-RAID. WARNING: ALL DISK DATA WILL BE DELETED.
Exiting the Intel® Rapid Storage Technology Option ROM utility To exit the utility: 1. From the utility main menu, select 5. Exit, and then press .
5.2 Creating a RAID driver disk A floppy disk with the RAID driver is required when installing a Windows® operating system on a hard disk drive that is included in a RAID set. The motherboard does not provide a floppy drive connector. You have to use a USB floppy disk drive when creating a SATA RAID driver disk. 5.2.1 Creating a RAID driver disk without entering the OS To create a RAID driver disk without entering the OS: 1. Boot your computer. 2.
5.2.3 Installing the RAID driver during Windows® OS installation To install the RAID driver for Windows® 7 or later OS: 1. During the OS installation, click Load Driver to allow you to select the installation media containing the RAID driver. 2. Insert the USB flash drive with RAID driver into the USB port or the support DVD into the optical drive, and then click Browse. 3.
Chapter 5 5-10 Chapter 5: RAID support
Appendices Appendices Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • • This device may not cause harmful interference. This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
IC: Canadian Compliance Statement Complies with the Canadian ICES-003 Class B specifications. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. This device complies with Industry Canada license exempt RSS standard(s).
REACH Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, we published the chemical substances in our products at ASUS REACH website at http://csr.asus.com/english/REACH.htm. DO NOT throw the motherboard in municipal waste. This product has been designed to enable proper reuse of parts and recycling.
Bluetooth Industry Canada Statement This Class B device meets all requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la Class B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
ASUS contact information ASUSTeK COMPUTER INC. Address Telephone Fax E-mail Web site Technical Support Telephone Online support 15 Li-Te Road, Peitou, Taipei, Taiwan 11259 +886-2-2894-3447 +886-2-2890-7798 info@asus.com.tw www.asus.com.tw +86-21-38429911 support.asus.
(510)739-3777/(510)608-4555 800 Corporate Way, Fremont, CA 94539. Asus Computer International Signature : Date : Representative Person’s Name : Apr. 16, 2013 Steve Chang / President This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ASUS MAXIMUS VI EXTREME A-7 (510)739-3777/(510)608-4555 800 Corporate Way, Fremont, CA 94539. Asus Computer International Appendices Signature : Date : Representative Person’s Name : Apr. 16, 2013 Steve Chang / President This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Appendices A-8 Appendices
