R MEB Socket 370 AGP Motherboard USER’S MANUAL
USER'S NOTICE No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS CONTACT INFORMATION ASUSTeK COMPUTER INC. (Asia-Pacific) Marketing Address: Telephone: Fax: Email: 150 Li-Te Road, Peitou, Taipei, Taiwan 112 +886-2-2894-3447 +886-2-2894-3449 info@asus.com.tw Technical Support Tel (English): Tel (Chinese): Fax: Email: Newsgroup: WWW: FTP: +886-2-2894-3447 ext. 706 +886-2-2894-3447 ext. 701 +886-2-2895-9254 tsd@asus.com.tw news2.asus.com.tw www.asus.com.tw ftp.asus.com.
CONTENTS I. INTRODUCTION .............................................................................. 7 How this manual is organized ............................................................. 7 Item Checklist ..................................................................................... 7 II. FEATURES ....................................................................................... 8 The ASUS MEB Motherboard ............................................................
CONTENTS Load BIOS Defaults .................................................................... 54 Load Setup Defaults .................................................................... 54 Supervisor Password and User Password ................................... 55 IDE HDD Auto Detection ........................................................... 56 Save & Exit Setup ....................................................................... 57 Exit Without Saving ............................................
FCC & DOC COMPLIANCE Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
I. INTRODUCTION I. INTRODUCTION Sections/Checklist How this manual is organized This manual is divided into the following sections: I. II. III. IV. V. VI.
II. FEATURES The ASUS MEB Motherboard II. FEATURES Features The ASUS MEB motherboard is carefully designed for the demanding PC user who wants many intelligent features in a small package. • Intel Processor Support: Supports Intel’s Celeron processor designed for the Socket 370 and packaged in Plastic Pin Grid Array (PPGA). • Intel AGPset: Features Intel’s 440BX AGPset with I/O subsystems and front side bus (FSB) platform, which boosts the traditional 66MHz internal bus to 100MHz.
II. FEATURES • • • Easy Installation: Equipped with BIOS that supports autodetection of hard drives, PS/2 mouse, and Plug and Play devices to make setup of hard drives, expansion cards, and other devices virtually automatic. IrDA: Supports an optional infrared port module for wireless interface. Quick Adjustments: Easy-to-access DIP switches make changing CPU frequencies and onboard function settings a snap. II.
II. FEATURES II. FEATURES Smart Series Intelligence (some features require the optional Hardware/Thermal Monitor) • Fan Status Monitoring and Alarm: To prevent system overheat and system damage, the CPU, power supply, and system fans can be monitored for RPM and failure. All the fans are set for its normal RPM range and alarm thresholds.
II. FEATURES Parts of the ASUS MEB Motherboard ATX Power Intel 440BX AGPset IDE DIP 3 DIMM Slots Connectors Switches Socket 370 II.
III.
III. HARDWARE SETUP Motherboard Settings 1) 2) 3) 4) 5) KBPWR DIP-Switch 5 DIP-Switch 6 DIP-Switch 7,8,9,10 DIP-Switch 1,2,3,4 p. 14 Keyboard Power Up (Enable/Disable) p. 15 Onboard Audio Setting p. 15 VIO Setting p. 16 CPU Bus Frequency Selection p. 16 CPU Core:Bus Frequency Multiple Expansion Slots/Sockets 1) 2) 3) 4) 5) DIMM1, DIMM2, DIMM3 Socket 370 SLOT1, SLOT2, SLOT3 PCI1, PCI2, PCI3, PCI4 AGP p. 17 168-Pin DIMM Memory Support p. 19 Central Processing Unit (CPU) Socket p.
III. HARDWARE SETUP Hardware Setup Steps Before using your computer, you must complete the following steps: 1. 2. 3. 4. 5. 6. Check Motherboard Settings Install Memory Modules Install the Central Processing Unit (CPU) Install Expansion Cards Connect Ribbon Cables, Panel Wires, and Power Supply Setup the BIOS Software 1. Motherboard Settings III.
III. HARDWARE SETUP DIP Switches (DIP) ON OFF ON 1 2 3 4 5 6 7 8 9 10 Some of the motherboard’s onboard functions can be adjusted through the DIP switches. The white block represents the switch’s position. The example below shows all the switches in the OFF position. 0 1
III. HARDWARE SETUP 4. CPU External (BUS) Frequency Selection (DIP-Switches 7, 8, 9, 10) These function switches tell the clock generator what frequency to send to the CPU. These allow the selection of the CPU’s External frequency (or BUS Clock). The BUS Clock times the BUS Ratio equals the CPU's Internal frequency (the advertised CPU speed). 150MHz 37.5MHz 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 ON ON 1 2 3 4 5 6 7 8 9 10 140MHz 35MHz ON 133MHz 44.
III. HARDWARE SETUP 2. System Memory (DIMM) NOTE: No hardware or BIOS setup is required after adding or removing memory. This motherboard uses only Dual Inline Memory Modules (DIMMs). Sockets are available for 3.3Volt (power level) unbuffered Synchronous Dynamic Random Access Memory (SDRAM) of either 8, 16, 32, 64, 128MB, or 256MB.
III. HARDWARE SETUP DIMM Memory Installation Insert the module(s) as shown. Because the number of pins are different on either side of the breaks, the module will only fit in the orientation as shown. DIMM modules are longer and have different pin contact on each side and therefore have a higher pin density. SIMM modules have the same pin contact on both sides. Lock FRONT 20 Pins 60 Pins 88 Pins 0 1 0 1 0 1 III. H/W SETUP System Memory MEB 168-Pin DIMM Sockets The DIMMs must be 3.
III. HARDWARE SETUP 3. Central Processing Unit (CPU) The motherboard provides a ZIF Socket 370. The CPU that came with the motherboard should have a fan attached to it to prevent overheating. If this is not the case then purchase a fan before you turn on your system. WARNING! Be sure that there is sufficient air circulation across the processor’s heatsink by regularly checking that your CPU fan is working.
III. HARDWARE SETUP (This page was intentionally left blank.) III.
III. HARDWARE SETUP 4. Expansion Cards WARNING! Make sure that you unplug your power supply when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. Expansion Card Installation Procedure III. H/W SETUP Expansion Cards 1. Read the documentation for your expansion card and make any necessary hardware or software settings for your expansion card, such as jumpers. 2.
III. HARDWARE SETUP To simplify this process this motherboard has complied with the Plug and Play (PNP) specification which was developed to allow automatic system configuration whenever a PNP-compliant card is added to the system. For PNP cards, IRQs are assigned automatically from those available. If the system has both Legacy and PNP ISA cards installed, IRQs are assigned to PNP cards from those not used by Legacy cards.
III. HARDWARE SETUP 5. External Connectors WARNING! Some pins are used for connectors or power sources. These are clearly distinguished from jumpers in the Motherboard Layout. Placing jumper caps over these connector pins will cause damage to your motherboard. IMPORTANT: Ribbon cables should always be connected with the red stripe on the Pin 1 side of the connector. The four corners of the connectors are labeled on the motherboard.
III. HARDWARE SETUP 3. Universal Serial BUS Ports 1 & 2 (Two 4-pin USB) Two USB ports are available for connecting USB devices. USB 1 Universal Serial Bus (USB) 2 4. Parallel Port Connector (25-pin PRINTER) You can enable the parallel port and choose the IRQ through “Onboard Parallel Port” in Chipset Features Setup of BIOS SETUP. NOTE: Serial printers must be connected to the serial port. III. H/W SETUP Connectors Parallel (Printer) Port (25-pin Female) 5.
III. HARDWARE SETUP 6. Joystick/Midi Connector (optional) (15-pin GAME_AUDIO) You may connect game joysticks or game pads to this connector for playing games. Connect MIDI devices for playing or editing audio. Joystick/Midi (15-pin Female) III. H/W SETUP Connectors 7. Audio Port Connectors (optional) (Three 1/8” GAME_AUDIO) Line Out can be connected to headphones or preferably powered speakers.
III. HARDWARE SETUP 9. Primary / Secondary IDE Connectors (Two 40-1pin IDE) These connectors support the provided IDE hard disk ribbon cable. After connecting the single end to the board, connect the two plugs at the other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accordingly. Please refer to the documentation of your hard disk for the jumper settings.
III. HARDWARE SETUP 11. Chassis, CPU , & Power Supply Fan Connectors (3-pin CHA_, CPU_, PWR_FAN) These connectors support cooling fans of 500mAMP (6 Watts) or less. Orientate the fans so that the heat sink fins allow airflow to go across the onboard heat sink(s) instead of the expansion slots. Depending on the fan manufacturer, the wiring and plug may be different. The red wire should be positive, while the black should be ground.
III. HARDWARE SETUP 13. Wake-On-Ring Connector (2-pin WOR) These connector connects to internal modem cards with a Wake-On-Ring output. The connector powers up the system when a ringup packet or signal is received through the internal modem card. NOTE: For external modems, Wake-On-Ring is detected through the COM port.
III. HARDWARE SETUP 15. IDE Device Activity LED (2-pin IDELED) This connector supplies power to the cabinet’s hard disk or IDE activity LED. Read and write activity by devices connected to the Primary or Secondary IDE connectors will cause the LED to light up. 0 1 0 1 0 1 TIP: If the case-mounted LED does not light, try reversing the 2-pin plug. IDELED III. H/W SETUP Connectors MEB IDE Activity LED 16.
III. HARDWARE SETUP 17. Chassis Intrusion Sensor Lead (4-1 pin CHASIS) This lead is for a chassis intrusion monitor or sensor. The sensor is triggered when a high level signal is sent to the “chassis signal” lead. This occurs when a panel switch or light detector is triggered. This function requires an optional trigger switch, such as the ASUS CIDB Chassis Intrusion Photo Sensor Module (See APPENDIX) and/or a chassis mounted toggle switch, to be installed. Chassis Signal Ground 0 1 0 1 +5VSB 0 1 III.
III. HARDWARE SETUP 19. Stereo Audio In Connectors (4-pin AUX, CD1, CD2) These connectors allow you to receive stereo audio input from an internal CDROM drive or other sound sources such as a TV tuner or MPEG card. Left Audio Channel Ground Ground Right Audio Channel 0 1 0 1 0 1 AUX CD1 Right Audio Channel Ground Ground Left Audio Channel MEB Internal Audio In Connectors Right Audio Channel Ground Left Audio Channel Ground CD2 III. H/W SETUP Connectors 20.
III. HARDWARE SETUP For Items 21-27 0 1 0 1 0 1 * Requires an ATX power supply. Speaker Connector Reset Switch ATX Power Switch Keyboard Lock Power LED SMI Lead Message LED MEB System Panel Connectors III. H/W SETUP Connectors 21. Message LED Lead (2-pin MSG.LED) This indicates whether a message has been received from a fax/modem. The LED will remain lit when there is no signal and blink when there is data transfer or waiting in the inbox. This function requires ACPI OS and driver support. 22.
III. HARDWARE SETUP III. H/W SETUP Connectors 24. Reset Switch Lead (2-pin RESET) This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting to prolong the life of the system’s power supply. 25. System Power LED (3-1 pin PWR.LED) This 3-1 pin connector connects the system power LED, which lights when the system is powered on and blinks when it is in sleep mode. 26.
III. HARDWARE SETUP (This page was intentionally left blank.) III.
III. HARDWARE SETUP Power Connection Procedures 1. After all connections are made, close the system case cover. 2. Be sure that all switches are off (in some systems, marked with ). 3. Connect the power supply cord into the power supply located on the back of your system case according to your system user’s manual. 4. Connect the power cord into a power outlet that is equipped with a surge protector. III. H/W SETUP Power Connections 5. You may then turn on your devices in the following order: a.
IV. BIOS SETUP Flash Memory Writer Utility AFLASH.EXE: This is the Flash Memory Writer utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM chip on the motherboard. To determine the BIOS version of your motherboard, check the last four numbers of the code displayed on the upper left-hand corner of your screen during bootup. Larger numbers represent a newer BIOS file. This file works only in DOS mode.
IV. BIOS SETUP 2. Update BIOS Including Boot Block and ESCD This option updates the boot block, the baseboard BIOS, and the ACPI extended system configuration data (ESCD) parameter block from a new BIOS file. See the next page for procedures on downloading an updated BIOS file. To update your current BIOS, type [2] at the Main Menu and then press . The Update BIOS Including Boot Block and ESCD screen appears. Type the filename of your new BIOS and the path, for example, A:\XXX-XX.
IV. BIOS SETUP Managing and Updating Your Motherboard’s BIOS Upon First Use of the Computer System 1. Create a bootable system floppy disk by typing [FORMAT A:/S] from the DOS prompt without creating “AUTOEXEC.BAT” and “CONFIG.SYS” files. 2. Copy AFLASH.EXE to the just created boot disk. 3. Run AFLASH.EXE from this new disk and select option 1. Save Current BIOS to File. See 1. Save Current BIOS To File on the previous page for more details and the rest of the steps.
IV. BIOS SETUP 6. BIOS Setup The motherboard supports two programmable Flash ROM chips: 5-Volt and 12Volt. Either of these memory chips can be updated when BIOS upgrades are released. Use the Flash Memory Writer utility to download the new BIOS file into the ROM chip as described in detail in this section. All computer motherboards provide a Setup utility program for specifying the system configuration and settings.
IV. BIOS SETUP Load Defaults The “Load BIOS Defaults” option loads the minimum settings for troubleshooting. “Load Setup Defaults”, on the other hand, is for loading optimized defaults for regular use. Choosing defaults at this level, will modify all applicable settings. A section at the bottom of the above screen displays the control keys for this screen. Take note of these keys and their respective uses.
IV. BIOS SETUP Time To set the time, highlight the “Time” field and then press either / or <+>/<–> to set the current time. Follow the hour, minute and second format. Valid values for hour, minute and second are: (Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59). NOTE: You can bypass the date and time prompts by creating an AUTOEXEC.BAT file. For information on how to create this file, please refer to the MS-DOS manual.
IV. BIOS SETUP Auto detection of hard disks on bootup For each field: Primary Master, Primary Slave, Secondary Master, and Secondary Slave, you can select Auto under the TYPE and MODE fields. This will enable auto detection of your IDE hard disk during bootup. This will allow you to change your hard disks (with the power off) and then power on without having to reconfigure your hard disk type.
IV. BIOS SETUP BIOS Features Setup The “BIOS Features Setup” option consists of configuration entries that allow you to improve your system performance, or let you set up some system features according to your preference. Some entries are required by the motherboard’s design to remain in their default settings. IV. BIOS SETUP BIOS Features A section at the lower right of the screen displays the control keys you can use. Take note of these keys and their respective uses.
IV. BIOS SETUP CPU Level 1 Cache / CPU Level 2 Cache (Enabled) These fields allow you to choose from the default of Enabled or choose Disabled to turn on or off the CPU’s Level 1 and Level 2 built-in cache. CPU Level 2 Cache ECC Check (Disabled) This function controls the ECC check capability in the CPU level 2 cache. BIOS Update (Enabled) This functions as an update loader integrated into the BIOS to supply the processor with the required data.
IV. BIOS SETUP PS/2 Mouse Function Control (Auto) The default of Auto allows the system to detect a PS/2 mouse on bootup. If detected, IRQ12 will be used for the PS/2 mouse. IRQ12 will be reserved for expansion cards if a PS/2 mouse is not detected. Enabled will always reserve IRQ12, whether on bootup a PS/2 mouse is detected or not.
IV. BIOS SETUP Chipset Features Setup The “Chipset Features Setup” option controls the configuration of the board’s chipset. NOTE: SETUP Defaults are noted in parenthesis next to each function heading. Details of Chipset Features Setup IV. BIOS SETUP Chipset Features SDRAM Configuration (By SPD) This sets the optimal timings of settings for items 2–5, depending on the memory modules that you are using.
IV. BIOS SETUP 16-bit I/O Recovery Time (1 BUSCLK) / 8-bit I/O Recovery Time (1 BUSCLK) Timing for 16-bit and 8-bit ISA cards, respectively. Leave on default setting. Graphics Aperture Size (64MB) Memory-mapped, graphics data structures can reside in a Graphics Aperture. Leave on default setting. Video Memory Cache Mode (UC) USWC (uncacheable, speculative write combining) is a new cache technology for the video memory of the processor. It can greatly improve the display speed by caching the display data.
IV. BIOS SETUP IV. BIOS SETUP Chipset Features Onboard Parallel Port (378H/IRQ7) This field sets the address of the onboard parallel port connector. You can select either: 3BCH / IRQ 7, 378H / IRQ 7, 278H / IRQ 5, Disabled. If you install an I/O card with a parallel port, ensure that there is no conflict in the address assignments. The PC can support up to three parallel ports as long as there are no conflicts for each port.
IV. BIOS SETUP Power Management Setup The “Power Management Setup” option allows you to reduce power consumption. This feature turns off the video display and shuts down the hard disk after a period of inactivity. NOTE: SETUP Defaults are noted in parenthesis next to each function heading. Details of Power Management Setup IV. BIOS SETUP Power Management Power Management (User Define) This field acts as the master control for the power management modes.
IV. BIOS SETUP Video Off Method (DPMS OFF) This field defines the video off features. The following options are available: DPMS OFF, DPMS Reduce ON, Blank Screen, V/H SYNC+Blank, DPMS Standby, and DPMS Suspend. The DPMS (Display Power Management System) features allow the BIOS to control the video display card if it supports the DPMS feature. Blank Screen only blanks the screen (use this for monitors without power management or “green” features.
IV. BIOS SETUP PWR Up On Modem Act (Enabled) This allows either settings of Enabled or Disabled for powering up the computer (turns the ATX power supply on) when the modem receives a call while the computer is Soft-off. NOTE: The computer cannot receive or transmit data until the computer and applications are fully running, thus connection cannot be made on the first try.
IV. BIOS SETUP PNP and PCI Setup The “PNP and PCI Setup” option configures the PCI bus slots. All PCI bus slots on the system use INTA#, thus all installed PCI cards must be set to this value. NOTE: SETUP Defaults are noted in parenthesis next to each function heading. Details of PNP and PCI Setup PNP OS Installed (No) This field allows you to use a Plug-and-Play (PnP) operating system to configure the PCI bus slots instead of using the BIOS.
IV. BIOS SETUP IRQ xx Used By ISA (No/ICU) These fields indicate whether or not the displayed IRQ for each field is being used by a legacy (non-PnP) ISA card. Two options are available: No/ICU and Yes. The first option, the default value, indicates either that the displayed IRQ is not used or an ISA Configuration Utility (ICU) is being used to determine if an ISA card is using that IRQ.
IV. BIOS SETUP Load BIOS Defaults The “Load BIOS Defaults” option allows you to load the troubleshooting default values permanently stored in the BIOS ROM. These default settings are non-optimal and disable all high performance features. To load these default settings, highlight “Load BIOS Defaults” on the main screen and then press . The system displays a confirmation message on the screen. Press and then to confirm. Press and then to abort.
IV. BIOS SETUP Supervisor Password and User Password These two options set the system passwords. “Supervisor Password” sets a password that will be used to protect the system and the Setup utility; “User Password” sets a password that will be used exclusively on the system. By default, the system comes without any passwords. To specify a password, highlight the type you want and then press . A password prompt appears on the screen.
IV. BIOS SETUP IDE HDD Auto Detection The “IDE HDD Auto Detection” option detects the parameters of an IDE hard disk drive, and automatically enters them into the Standard CMOS Setup screen. IV. BIOS SETUP Hard Disk Detect Up to four IDE drives can be detected, with parameters for each listed inside the box. To accept the optimal entries, press or else select from the numbers displayed under the OPTIONS field (2, 1, 3 in this case); to skip to the next drive, press .
IV. BIOS SETUP IMPORTANT: If your hard disk was already formatted on an older previous system, incorrect parameters may be detected. You will need to enter the correct parameters manually or use low-level format if you do not need the data stored on the hard disk. If the parameters listed differ from the ones used when the disk was formatted, the disk will not be readable. If the auto-detected parameters do not match the ones that should be used for your disk, do not accept them.
IV. BIOS SETUP (This page was intentionally left blank.) IV.
V.
V. SOFTWARE SETUP Operating Systems ............................................................................... MEB Support CD (Windows 98) ........................................................ Support CD Contents ....................................................................... Installing ESS Audio Driver (with onboard audio) ......................... Installing AudioRack32 (with onboard audio) ................................. Installing Software Wavetable (with onboard audio) ...............
V. SOFTWARE SETUP Operating Systems You should always use the latest operating system and updates when using new hardware in order to ensure full compliancy. For Windows 95, you must use OSR 2.0 or later. For Windows NT 4.0, you must use Service Pack 3.0 or later. MEB Support CD (Windows 98) V. S/W SETUP Operating Systems Insert the support CD or double-click your CD drive icon in My Computer to bring up the autorun menu or run Setup.exe in the root directory of the Support CD.
V. SOFTWARE SETUP Support CD Contents • V. S/W SETUP Windows 98 LDCM Local Setup (with hardware monitor only): Installs software to monitor the local system. The LANDesk Client Manager must be installed in order to use the hardware manager features. • LDCM Administrator Setup (with hardware monitor only): Installs software to monitor PC systems on the network within the same bridge address with the Local software installed. The administrator should install both Local and Administrator Software.
V. SOFTWARE SETUP Installing ESS Audio Driver (with onboard audio) Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the autorun screen. 3. Browse to E:\AUDIO\W95 (assuming E is your CD-ROM drive) and then click here. 4. Click here. V. S/W SETUP Windows 98 1. Click here. 2. Select Search for the best driver for your device and then click here. 5. Click here.
V. SOFTWARE SETUP Installing AudioRack32 (with onboard audio) Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the autorun screen. 1. Click here. 2. Click here. 3. Click here. V. S/W SETUP Windows 98 4. Click here to start AudioRack32.
V. SOFTWARE SETUP Installing Software Wavetable (with onboard audio) Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the autorun screen. 1. Click here. V. S/W SETUP Windows 98 2. Click here. 3. Select Install ESS Software Wavetable and then click here.
V. SOFTWARE SETUP Installing PCCillin Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the autorun screen. 1. Click here. 2. Click here. 3. Enter your name and company and then click here. 4. Click here. 6. Insert a floppy disk and then click here. 5. Click Express Install and then click here. V. S/W SETUP Windows 98 7. Once the Emergency Clean disk is created, click here.
V. SOFTWARE SETUP Installing Adobe Acrobat Reader Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the autorun screen. 1. Click here. 2. Click here. V. S/W SETUP Windows 98 4. Click here. 3. Click here. 5. Click here.
V. SOFTWARE SETUP Installing ASUS PC Probe Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the autorun screen. NOTE: ASUS PC Probe will not run if Intel’s LDCM utility is installed. To uninstall Intel’s LDCM utility, see section on Uninstalling Programs. 2. Click here. 1. Click here. 3. Click here. V. S/W SETUP Windows 98 4. Make any desired setting changes and then click here. 5. Click here.
V. SOFTWARE SETUP LDCM Local Setup Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the autorun screen. NOTE: LDCM will not run if ASUS’ PC Probe utility is installed. To uninstall PC Probe, see section on Uninstalling Programs. 1. Click here. 4. Click here. V. S/W SETUP Windows 98 3. Click here. 2. Click here. 5. Select the components you want to install and then click here. ASUS MEB User’s Manual 6.
V. SOFTWARE SETUP LDCM Local Setup (Cont’d) 7. Click here. 8. Click here. 9. Click here. 10. Click here. V. S/W SETUP Windows 98 11. Click here and then click Finish to restart.
V. SOFTWARE SETUP LDCM Administrator Setup Insert the Support CD that came with your motherboard into your CD-ROM drive or double-click the CD drive icon in My Computer to bring up the autorun screen. NOTE: LDCM will not run if ASUS’ PC Probe utility is installed. To uninstall PC Probe, see section on Uninstalling Programs. 1. Click here. 2. Click here. 4. Click here. V. S/W SETUP Windows 98 3. Click here. 5. Click here and then click Finish to restart.
V. SOFTWARE SETUP Uninstalling Programs Add/Remove Programs is a basic component within Windows. You may use this function if a program does not provide its own uninstallation program. 1. Double-click here to open the Add/Remove Programs Properties dialog box. 2. Select the program you wish to remove and click here. V. S/W SETUP Windows 98 3. Click here.
VI. S/W REFERENCE AudioRack VI.
VI. SOFTWARE REFERENCE VI. S/W REFERENCE AudioRack AudioRack32 ........................................................................................ The Command Center ...................................................................... The Miniature Mode ........................................................................ The Audio Mixer .............................................................................. The Digital Audio Player .........................................................
VI. SOFTWARE REFERENCE VI. S/W REFERENCE AudioRack AudioRack32 The AudioRack32 enables you to take advantage of your computer’s audio capabilities with all of the controls conveniently in one compact space. You can play audio CDs, wave files (in WAV and .AUD formats), and MIDI files (in.MID and .RMI formats). With the multisource Audio Mixer, you can blend these sources with linein and microphone sources any way you choose.
VI. SOFTWARE REFERENCE VI. S/W REFERENCE AudioRack The Command Center The Command Center controls which parts of the AudioRack32 are displayed. You can display or hide any part of the AudioRack32 you choose, customizing its appearance to suit your needs or desires. It also displays information on the status of the different audio components. Counters Component Icons (DAT, MIDI, CD) Transport State Indicators Track or File Names Time Indexes The Command Center Controls closes the AudioRack32 window.
VI. SOFTWARE REFERENCE VI. S/W REFERENCE AudioRack The Miniature Mode The Miniature mode is designed to give you full control of the AudioRack32 while using a minimum of space. You are able to effectively use the AudioRack32 and still have enough room on your desktop to run other applications. In the Miniature mode, you can play, pause, stop, and control the master volume of the AudioRack32.
VI. SOFTWARE REFERENCE VI. S/W REFERENCE AudioRack The Audio Mixer The Audio Mixer has two modes: Playback mode and Record mode. You can use these two modes to fully control which of your audio sources you are listening to or recording, how loud each of those sources are and how they are balanced. Each audio source has its own module with mute, balance and volume controls. In addition, the Audio Mixer provides special effects controls for chorus, reverb, treble, bass, and 3-D effects.
VI. S/W REFERENCE AudioRack VI. SOFTWARE REFERENCE The Digital Audio Player The Digital Audio Player enables you to play, record, and compress sound as .WAV files. In addition, you can play .AUD files. The .WAV files use PCM, which is the Windows‘ audio file format. The.AUD format uses ESPCM‘ compression to produce an audio file. Files are written directly to your hard disk as you record, enabling you to record very large files. Your only limitation is the amount of free space on your hard disk.
VI. SOFTWARE REFERENCE VI. S/W REFERENCE AudioRack The MIDI Player The MIDI Player enables you to play MIDI files with the .MID or .RMI file extensions. These MIDI (Musical Instrument Digital Interface) files can be produced by sequencer programs and then played back using the MIDI Player. You can also mix MIDI files with other audio sources. Or you can compile MIDI files in a playlist and play them back in any order you choose. The MIDI Player Controls plays the MIDI file currently loaded.
VI. SOFTWARE REFERENCE VI. S/W REFERENCE AudioRack The Compact Disk Player If you have a CD-ROM drive, you can play audio CDs. Check your hardware manual about setting up CD audio hardware and drivers. The Compact Disk Player uses intelligent CD playlist management: The Compact Disk Player maintains a record of each CD you play. It remembers the last playlist you used with each CD and loads that playlist automatically whenever you insert that CD.
VI. SOFTWARE REFERENCE VI. S/W REFERENCE AudioRack The Audio Recorder The Audio Recorder enables you to record, compress, store, and play back voice, music, and other sound. It provides settings for sound attributes such as mono/stereo, compression level, and sampling rate. You can use it to embed sound objects in documents created in applications that support object linking and embedding (OLE).
VI. SOFTWARE REFERENCE VI. S/W REFERENCE AudioRack Release Notes This information is provided for convenience only. Information here is subject to change without prior notice. View the installation CD for any updated information in Readme text files. The AudioRack also provides detailed online help (click the Help button on the “Command Center”) Disable Eject Button on the CD Player Under the Windows directory in the file “auddrive.
VI. SOFTWARE REFERENCE VI.
VI. SOFTWARE REFERENCE VI. S/W REFERENCE ASUS PC Probe ASUS PC Probe ASUS PC Probe is a convenient utility to monitor the computer system’s vital components: fan rotations, voltages, and temperatures. Starting ASUS PC Probe When ASUS PC Probe starts, a splash screen appears allowing you to “Show Monitor” or “Hide”. You can select whether you want the splash screen to show the next time it opens.
VI. SOFTWARE REFERENCE VI.
VI. SOFTWARE REFERENCE VI. S/W REFERENCE ASUS PC Probe Using the ASUS PC Probe PC Probe System Info. Get information on your mainboard and BIOS from this screen. PC Probe Settings Change PC Probe refresh times here Click here to start PC Probe each time you enter Windows. Click the items you wish to reset to its default values and click this button. PC Probe Task Bar Icon Right clicking the PC Probe icon will bring up a menu to turn on, off, or exit ASUS PC Probe.
VI. SOFTWARE REFERENCE VI. S/W REFERENCE Intel LDCM Intel LANDesk Client Manager With the growth of the computer industry, computer systems have become more complex and difficult to manage. Intel LANDesk Client Manager is a computer management application that simplifies many aspects of managing a computer and assists in troubleshooting common computer problems.
VI. SOFTWARE REFERENCE VI.
VI. SOFTWARE REFERENCE VI.
VI. SOFTWARE REFERENCE VI. S/W REFERENCE Intel LDCM To select a computer 1. From the main Client Manager window, click File | Select Computer. 2. In the Select Computer dialog box, click the computer you want to view. 3. Click the Select button. To discover new computers • In the Select Computer dialog box, click the Discover button on the toolbar or press +.
VI. SOFTWARE REFERENCE VI. S/W REFERENCE Intel LDCM After you attempt to wake up a computer, the status of that computer changes in the list view to a Wake Pending status. If the attempt to wake up a computer is successful, the Wake Pending status changes to a status reflecting the computer’s health (such as Normal, Warning, or Critical). If the computer does not wake up after five minutes, a message box appears stating possible reasons why the computer did not respond.
VI. SOFTWARE REFERENCE VI. S/W REFERENCE Intel LDCM Understanding the Computer Status Icons When you open the Select Computer dialog box, each computer in the list displays an icon indicating the current status of that computer. The table below describes the seven states a computer may be in. Unavailable The computer is currently in a powered-down state. Wakeable The computer is currently in a powered-down state but supports Remote Wakeup technology.
VI. SOFTWARE REFERENCE VI. S/W REFERENCE DMI Utility Desktop Management Interface (DMI) Introducing the ASUS DMI Configuration Utility This motherboard supports DMI within the BIOS level and provides a DMI Configuration Utility to maintain the Management Information Format Database (MIFD). DMI is able to auto-detect and record information pertinent to a computer’s system such as the CPU type, CPU speed, and internal/external frequencies, and memory size.
VI. SOFTWARE REFERENCE VI. S/W REFERENCE DMI Utility Using the ASUS DMI Configuration Utility NOTE: The following screen displays are provided as examples only and may not reflect the screen contents on your system. Edit DMI (or delete) Use the ←→ (left-right) cursors to move the top menu items and the ↑↓ (up-down) cursor to move between the left hand menu items. The bottom of the screen will show the available keys for each screen. Press enter at the menu item to enter the right hand screen for editing.
VI. SOFTWARE REFERENCE VI. S/W REFERENCE DMI Utility Save MIFD You can save the MIFD (normally only saved to flash ROM) to a file by entering the drive and path here. If you want to cancel save, you may press ESC and a message “Bad File Name” appears here to show it was not saved. Load MIFD You can load the disk file to memory by entering a drive and path and file name here. Load BIOS Defaults You can load the BIOS defaults from a MIFD file and can clear all user modified and added data.
APPENDIX The ASUS CIDB Chassis Intrusion Sensor Module The optional ASUS CIDB is a module for providing audio alarm and logging when there is an intrusion into the chassis of a computer system. The module detects a chassis intrusion by either light striking its photo sensor or by contact when its switch connectors are shorted by chassis-mounted momentary toggle switches. An intrusion memory function allows detection by BIOS and LDCM v3.3 on the next bootup.
APPENDIX Setting up the ASUS CIDB JP1 OR CON CR2032 3V Lithium Cell CLR SW JP1 JP1 1 1 Enable Disable JP1: Enable/Disable the Photo Sensor Buzzer APPENDIX ASUS CIDB 3 MS2 +5 volt standby from power supply MS1 CLR CLR Normal Clear MS1 0 (not sensitive) CON: Sensitivity adjustment for the photo sensor, (0) is least sensitive and (5) is most sensitive SW SW Clear: Stops the sounding alarm MS2 1 CON (sensitive) 5 best range 2 4 MS1/MS2: Micro Switch from the chassis panel can be co
APPENDIX APPENDIX ASUS LAN Card The ASUS PCI-L101 Fast Ethernet Card LEDs LAN Activity Output Signal Intel Chipset RJ45 Wake on LAN Output Signal ASUS Motherboard type Other If you are using the ASUS PCI-L101 on an ASUS motherboard, leave the jumper on its defaut setting of “ASUS.” If you are using another brand of motherboard, set the jumper to “Other.” Connect the Wake on LAN (WOL) output signal to the motherboard’s WOL_CON in order to utilize the wake on LAN feature of the motherboard.
APPENDIX Features APPENDIX ASUS LAN Card • • • • • • • • • • • • Intel 82558 Ethernet LAN Controller (Fully integrated 10BASE-T/100BASE-TX) Wake-On-LAN Remote Control Function Supported PCI Bus Master Complies to PCI Local Bus Rev. 2.1 specifications Consists of MAC & PHY (10/100Mbps) interfaces Complies to IEEE 802.3 10BASE-T and IEEE 802.3u 100BASE-TX interfaces Fully supports 10BASE-T & 100BASE-TX operations through a single RJ45 port Supports 32-bit Bus Master Technology / PCI Rev. 2.
APPENDIX Glossary AGP (Accelerated Graphics Port) An interface specification that enables high-performance 3D graphics on mainstream PCs. AGP offers a higher throughput than PCI by providing the graphics controller with direct access to system memory. Bus Frequency PCI AGP 1X AGP 2X AGP 4X 33MHz 66MHz 133MHz 266MHz Bus Speed 133MB/s 200-300MB/s 528MB/s 1 GB/s APPENDIX Glossary Bus AUTOEXEC.BAT AUTOEXEC.
APPENDIX Byte (Binary Term) One byte is a group of eight contiguous bits. A byte is used to represent a single alphanumeric character, punctuation mark, or other symbol. COM Port COM is a logical device name used by to designate the computer serial ports. Pointing devices, modems, and infrared modules can be connected to COM ports. Each COM port is configured to use a different IRQ and address assignment.
APPENDIX PCI Bus (Peripheral Component Interconnect Local Bus) PCI bus is a specification that defines a 32-bit data bus interface. PCI is a standard widely used by expansion card manufacturers. Peripherals Peripherals are devices attached to the computer via I/O ports. Peripheral devices allow your computer to perform an almost limitless variety of specialized tasks.
APPENDIX USB (Universal Serial Bus) A new 4-pin serial peripheral bus that allows plug and play computer peripherals such as keyboard, mouse, joystick, scanner, printer and modem/ISDN to be automatically configured when they are attached physically without having to install drivers or reboot. With USB, the traditional complex cables from back panel of your PC can be eliminated.
