Motherboard M2R32-MVP
E2717 First Edition V1 July 2006 Copyright © 2006 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Notices ............................................................................................... vii Safety information ............................................................................ viii About this guide ................................................................................. ix M2R32-MVP specifications summary .................................................. xi Chapter 1: Product introduction 1.1 Welcome! ........................................................
Contents 2.6 Jumper ............................................................................... 2-19 2.7 Connectors ......................................................................... 2-22 2.7.1 Rear panel connectors .......................................... 2-22 2.7.2 Internal connectors ............................................... 2-24 Chapter 3: iv Powering up 3.1 Starting up for the first time ................................................ 3-1 3.2 Powering off the computer .
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This guide contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports. • Chapter 2: Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components.
Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. D A N G E R / W A R N I N G : Information to prevent injury to yourself when trying to complete a task. C A U T I O N : Information to prevent damage to the components when trying to complete a task. I M P O R T A N T : Instructions that you MUST follow to complete a task. N O T E : Tips and additional information to help you complete a task.
M2R32-MVP specifications summary CPU Socket AM2 for AMD Athlon™ 64 X2/Athlon™ 64 FX/ Athlon™ 64/Sempron™ processor AMD64 architecture enables simultaneous 32- and 64-bit computing Supports AMD Cool ‘n’ Quiet™ Technology Supports AMD HyperTransport™ Technology Supports AMD Live!™ Ready Chipset ATI™ CrossFire™ Xpress 3200/ATI™ SB600 System bus 2000/1600 MT/s Memory Dual-channel memory architecture 4 x 240-pin DIMM sockets support up to 8 GB unbufferred ECC/non-ECC 800/667/533 MHz DDR2 memory modules E
M2R32-MVP specifications summary ASUS special features Stack Cool 2 ASUS SATA On-the-Go (External Serial ATA port on the rear panel) Noise Filter ASUS EZ DIY: - ASUS CrashFree BIOS 3 - ASUS EZ Flash 2 - ASUS Q-Connector ASUS MyLogo2 ASUS Q-Fan2 Technology Overclocking Intelligent overclocking tools: - AI NOS™ (Non-delay Overclocking System) - AI Overclocking (intelligent CPU frequency tuner) - ASUS PEG Link (automatic performance tuning for single/dual graphics cards) - AI Clock Skew ASUS O.C.
M2R32-MVP specifications summary Internal connectors 3 x USB 2.0 connectors for six additional USB 2.
xii
This chapter describes the motherboard features and the new technologies it supports 1 Product information
Chapter summary 1 1.1 Welcome! .............................................................................. 1-1 1.2 Package contents ................................................................. 1-1 1.3 Special features ....................................................................
1.1 Welcome! T h a n k y o u f o r b u y i n g a n A S U S® M 2 R 3 2 - M V P m o t h e r b o a r d ! The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your motherboard package for the following items.
1.3 Special features 1.3.1 Product highlights Latest processor technology The motherboard supports AMD socket AM2 single-core Athlon 64/ Sempron and dual-core Athlon 64 X2/Athlon 64 FX processors with 2MB/ 1MB/512KB L2 cache, which is based on 64-bit architecture. It features 2000/1600 MT/s HyperTransport Bus, dual-channel un-buffered DDR2 800 memory support and AMD Cool ‘n’ Quiet Technology. See page 2-6 for details.
Serial ATA 3.0 Gb/s technology and SATA-On-The-Go The motherboard fully supports the Serial ATA II 3.0 Gb/s technology through the Serial ATA interfaces and the ATI® SB 600 chipset. The Serial ATA 3.0 Gb/s specification provides twice the bandwidth of the current Serial ATA products with a host of new features, including Power Management (PM) Implementation Algorithm. Serial ATA allows for thinner, more flexible cables with lower pin count and reduced voltage required. Leveraging these Serial ATA 3.
1.3.2 Innovative ASUS features ASUS Stack Cool 2 ASUS Stack Cool 2 is a fan-less and zero-noise cooling solution that lowers the temperature of critical heat generating components. The motherboard uses a special design on the printed circuit board (PCB) to dissipate heat that critical components generate. AI NET2 The AI NET2 is a BIOS-based diagnostic tool that detects and reports Ethernet cable faults and shorts.
PEG Link Mode for two graphics cards This feature enhances your PCI Express graphics card performance, allowing the motherboard to automatically adjust the PCI Express graphics link mode to the correct frequency based on the system configuration. Four additional settings are available for overclocking the PEG Link Mode. ASUS Q-Fan 2 technology The ASUS Q-Fan 2 technology smartly adjusts the CPU and chassis fans speed according to the system loading to ensure quiet, cool, and efficient operation.
ASUS Multi-language BIOS The multi-language BIOS allows you to select the language of your choice from the available options. The localized BIOS menus allow easier and faster configuration. ASUS MyLogo2™ ASUS My Logo2™ is the new feature present in the motherboard that allows you to personalize and add style to your system with customizable and animated boot logos. C.P.R. (CPU Parameter Recall) The C.P.R.
This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
Chapter summary 2 2.1 Before you proceed .............................................................. 2-1 2.2 Motherboard overview .......................................................... 2-2 2.3 Central Processing Unit (CPU) .............................................. 2-6 2.4 System memory ................................................................. 2-11 2.5 Expansion slots ................................................................... 2-15 2.6 Jumper .........................
2.1 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity • Hold components by the edges to avoid touching the ICs on them.
2.2 Motherboard overview Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Refer to the chassis documentation before installing the motherboard. Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components. 2.2.
2.2.3 Motherboard layout 24.5cm (9.6in) KBPWR1 PS/2KBMS T: Mouse B: Keyboard DDR2 DIMM_B2 (64 bit,240-pin module) COM1 CHA_FAN2 DDR2 DIMM_A2 (64 bit,240-pin module) CPU_FAN ESATA USBPW12 USBPW34 DDR2 DIMM_B1 (64 bit,240-pin module) DDR2 DIMM_A1 (64 bit,240-pin module) JMB360 PRI_IDE Socket AM2 LAN_USB34 30.5cm (12.
2.2.4 2-4 Layout Contents Slots Page 1. DDR DIMM slots 2-11 2. PCI slots 2-17 3. PCI Express x1 slots 2-17 4. PCI Express x16 slots 2-17 Jumper Page 1. Clear RTC RAM (3-pin CLRTC) 2-19 2. USB device wake-up (3-pin USBPW12, USBPW34, USBPW56, USBPW78, USBPW910) 2-20 3. Keyboard power (3-pin KBPWR1) 2-21 Rear panel connectors Page 1. 2-22 PS/2 mouse port (green) 2. IEEEa 1394 port 2-22 3. LAN (RJ-45) port 2-22 4. Rear Speaker Out port (black) 2-22 5.
Internal connectors Page 1. Floppy disk drive connector (34-1 pin FLOPPY) 2-24 2. IDE connectors (40-1 pin PRI_IDE) 2-24 3. Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4) 2-25 4. CPU, Chassis, and Power fan connectors (4-3 pin CPU_FAN, 3-pin CHA_FAN1, 3-pin CHA_FAN2, 3-pin PWR_FAN ) 2-27 5. USB connectors (10-1 USB56, USB78, USB910) 2-27 6. Power connectors (24-pin EATXPWR, 4-pin ATX12V) 2-28 7. IEEE 1394a connectors (10-1 pin IE1394_2) 2-29 8.
2.3 Central Processing Unit (CPU) The motherboard comes with a 940-pin AM2 socket designed for the AMD Athlon™ 64 X2/Athlon™ 64/Athlon™ FX/Sempron™ processor. The AM2 socket has a different pinout from the 939-pin socket designed for the AMD Opteron™ processor. Make sure you use a CPU is designed for the AM2 socket. The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU! 2.3.
3. Position the CPU above the socket such that the CPU corner with the gold triangle matches the socket corner with a small triangle. 4. Carefully insert the CPU into the socket until it fits in place. Small triangle Gold triangle The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to prevent bending the pins and damaging the CPU! 5. When the CPU is in place, push down the socket lever to secure the CPU. The lever clicks on the side tab to indicate that it is locked. 6.
2.3.2 Installing the heatsink and fan The AMD Athlon™ 64 X2/Athlon™ 64 FX/Athlon™ 64/Sempron™ processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. Make sure that you use only AMD-certified heatsink and fan assembly. To install the CPU heatsink and fan: 1. Place the heatsink on top of the installed CPU, making sure that the heatsink fits properly on the retention module base.
2. Attach one end of the retention bracket to the retention module base. 3. Align the other end of the retention bracket (near the retention bracket lock) to the retention module base. A clicking sound denotes that the retention bracket is in place. Make sure that the fan and heatsink assembly perfectly fits the retention mechanism module base, otherwise you cannot snap the retention bracket in place. 4.
5. When the fan and heatsink assembly is in place, connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN. ® CPU_FAN CPU FAN PWM CPU FAN IN CPU FAN PWR GND M2R32-MVP M2R32-MVP CPU fan connector Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector.
2.4 System memory 2.4.1 Overview The motherboard comes with four Double Data Rate 2 (DDR2) Dual Inline Memory Modules (DIMM) sockets. A DDR2 module has the same physical dimensions as a DDR DIMM but has a 240-pin footprint compared to the 184-pin DDR DIMM. DDR2 DIMMs are notched differently to prevent installation on a DDR DIMM socket.
2.4.2 Memory configurations You may install 256 MB, 512 MB, 1 GB, and 2 GB unbuffered ECC/non-ECC DDR2 DIMMs into the DIMM sockets. • For dual-channel configuration, the total size of memory module(s) installed per channel must be the same (DIMM_A1+ DIMM_B1 = DIMM_A2+ DIMM_B2) • Always install DIMMs with the same CAS latency. For optimum compatibility, we recommend that you obtain memory modules from the same vendor. Refer to the DDR2 Qualified Vendors List below for details.
DDR2 (800 MHz) Qualified Vendors List DIMM support Size Vendor Chip No. Brand Side/s* Part No.
2.4.3 Installing a DDR2 DIMM Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components. 2 1. Unlock a DIMM socket by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. 3. 3 1 1 Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated.
2.5 Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. 2.5.1 Installing an expansion card To install an expansion card: 1.
2.5.
2.5.4 Two PCI slots The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The figure shows a LAN card installed on a PCI slot. 2.5.5 Two PCI Express x1 slots This motherboard supports two PCI Express x1 network cards, SCSI cards and other cards that comply with the PCI Express specifications. The figure shows a network card installed on the PCI Express x1 slot. 2.5.
• We recommend that you install a VGA card on the primary (blue) PCI Express slot and install any other PCI Express device on the secondary (black) PCI Express slot. • In CrossFire™ mode, install the ATI CrossFire™ Edition (Master) graphics card on the primary (blue) PCI Express slot; otherwise, the system will not boot. • If you do not configure the PCI Express device (s) according to the table below, the system may have a failed or delayed power-on self test (POST).
2.6 Jumper 1 . Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the onboard battery. 3. Move the jumper cap from pins 1-2 (default) to pins 2-3.
2. USB device wake-up (3-pin USBPW12, USBPW34, USBPW56, USBPW78, USBPW910) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes. The USBPW12 and USBPW34 jumpers are for the rear USB ports. The USBPW56, USBPW78, and USBPW910 jumpers are for the internal USB connectors that you can connect to additional USB ports.
3. Keyboard power (3-pin KBPWR1) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) to wake up the computer when you press a key on the keyboard (the default is the Space Bar). This feature requires an ATX power supply that can supply at least 500 mA on the +5VSB lead, and a corresponding setting in the BIOS.
2.7 Connectors 2.7.1 Rear panel connectors 1 15 14 13 2 3 12 11 45 67 10 9 8 1. 2. P S / 2 m o u s e p o r t ( g r e e n ) . This port is for a PS/2 mouse. E E E 1 3 9 4 a p o r t . This 6-pin IEEE 1394a port provides high-speed connectivity for audio/video devices, storage peripherals, PCs, or portable devices. 3. L A N ( R J - 4 5 ) p o r t . Supported by Marvell® Gigabit LAN controller, this port allows Gigabit connection to a Local Area Network (LAN) through a network hub.
Audio 2, 4, 6, or 8-channel configuration Port Headset 2-channel 4-channel Line In Line In Line In Line In Lime Line Out Front Speaker Out Front Speaker Out Front Speaker Out Pink Mic In Mic In Mic In Mic In Gray • • • Side Speaker Out Black • Rear Speaker Out Rear Speaker Out Rear Speaker Out Orange • • Center/Subwoofer Center/Subwoofer Light Blue 8. 6-channel 8-channel C o a x i a l S / P D I F O u t p o r t .
2.7.2 1. Internal connectors Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. ® Pin 5 on the connector is removed to prevent incorrect cable connection when using an FDD cable with a covered Pin 5. FLOPPY NOTE: Orient the red markings on the floppy ribbon cable to PIN 1.
Drive jumper setting Mode of device(s) Cable connector Single device Cable-Select or Master - Black Two devices Cable-Select Master Black Slave Gray Master Master Slave Slave Black or gray If any device jumper is set as "Cable-Select," make sure all other device jumpers have the same setting. 3. Serial ATA connectors (7-pin SATA, SATA2, SATA3, SATA4) These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives.
right angle side Connect the right-angle side of SATA signal cable to SATA device. Or you may connect the right-angle side of SATA cable to the onboard SATA port to avoid mechanical conflict with huge graphics cards. • Plug your Serial ATA boot disk on the master port (SATA1/2 to support S3 function). • Install the Windows® 2000 Service Pack 4 or the Windows® XP Service Pack1 or later when using Serial ATA.
4. CPU, Chassis, and Power fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN1, 3-pin CHA_FAN2, 3-pin PWR_FAN) The fan connectors support cooling fans of 350 mA ~ 2000 mA (24 W max.) or a total of 1 A ~ 3.48 A (41.76 W max.) at +12 V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors.
5. USB connectors (10-1 pin USB56, USB78, USB910) 1 M2R32-MVP USB 2.0 connectors 1 USB56 NC GND USB_P8+ USB_P8USB+5V USB78 GND USB_P5+ USB_P5USB+5V M2R32-MVP NC GND USB_P6+ USB_P6USB+5V 1 GND USB_P7+ USB_P7USB+5V USB910 USB+5V USB_P9USB_P9+ GND ® USB+5V USB_P10USB_P10+ GND NC These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.
• For a fully-configured system, we recommend that you use a power supply unit (PSU) that complies with ATX 12 V Specification 2.0 (or later version) and provides a minimum power of 400 W. • Do not forget to connect the 4-pin ATX +12 V power plug; otherwise, the system will not boot up. • The ATX 12 V Specification 2.0 compliant (500 W) PSU has been tested to support the below configuration: CPU: Memory: Graphics card: Hard disk: ATAPI: 7.
8. Chassis intrusion connector (4-1 pin CHASSIS) This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. The signal is then generated as a chassis intrusion event.
1 0 . Front panel audio connector (10-1 pin AAFP) NC AGND NC NC SENSE2_RETUR ® AGND PRESENCE# SENSE1_RETUR This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC ‘97 audio standard. Connect one end of the front panel audio I/O module cable to this connector.
1 2 . System panel connector (20-8 pin PANEL) This connector supports several chassis-mounted functions. +5V Ground Ground Speaker PLED- SPEAKER ® PLED+ PLED IDE_LED M2R32-MVP Reset Ground PWR Ground IDE_LED+ IDE_LED- PANEL RESET PWRSW * Requires an ATX power supply. M2R32-MVP System panel connector • • • • • 2-32 System power LED This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector.
1 3 . Q-Connector (System panel) ASUS Q-Connector allows you to easily connect the chassis front panel cables to the motherboard. Perform these steps to install ASUS QConnector. step1. Connect the front panel cables to their respective connectors on the ASUS QConnector. Refer to the labels on the QConnector for proper connection and pin definition. step2. Carefully connect the ASUS Q-Connector to the System panel connector.
2-34 Chapter 2: Hardware information
This chapter describes the power up sequence, the vocal POST messages, and ways of shutting down the system.
Chapter summary 3 3.1 Starting up for the first time ................................................ 3-1 3.2 Powering off the computer ..................................................
3.1 Starting up for the first time 1. After making all the connections, replace the system case cover. 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: a. Monitor b. External SCSI devices (starting with the last device on the chain) c. System power 6.
3.2 Powering off the computer 3.2.1 Using the OS shut down function If you are using Windows® 2000: 2. Click the S t a r t button then click S h u t D o w n . . . Make sure that the S h u t D o w n option button is selected, then click the O K button to shut down the computer. 3. The power supply should turn off after Windows® shuts down. 1. If you are using Windows® XP: 2. Click the S t a r t button then select T u r n O f f C o m p u t e r .
