노트북 PC 하드웨어 사용자 설명서 K4017/2008년 7월
목차 목차 Table of Contents 1. 노트북 PC 소개 본 사용자 설명서에 대해 ������������������������������������������������� 6 설명서 참고 사항 ������������������������������������������������������ 6 노트북 PC 준비 ���������������������������������������������������������� 9 2.
목차 목차 (계속) 4.
목차
1. 노트북 PC 소개 사용자 설명서 정보 설명서 참고 사항 안전 예방 수칙 노트북 PC 준비 본 설명서내에 보여지는 그림과 노트북에서의 실제 모습은 차이가 있을 수 있습니다. 노트 북 PC의 내용이 설명서의 그림에 우선합니다. 참고: 본 설명서에 사용된 사진과 아이콘은 사용자의 이해를 돕기 위한 이미지이며, 제품 자체에서의 실제 모습과 다를 수 있습니다.
1 노트북 PC 소개 본 사용자 설명서에 대해 본 설명서는 ASUS 노트북 PC의 사용자 설명서입니다. 본 사용자 설명서는 노 트북 PC의 여러 가지 구성 요소와 사용 방법에 대한 정보를 제공합니다. 다음 은 사용자 설명서의 주요 내용입니다: 1. 노트북 PC 소개 노트북 PC와 사용자 설명서를 소개합니다. 2. 노트북 PC 기본 구성 노트북 PC의 각 구성 요소에 대한 정보를 제공합니다. 3. 노트북 PC 시작하기 노트북 PC 시작하기 위한 정보를 제공합니다. 4. 노트북 PC 사용하기 노트북 PC의 각 구성 요소에 대한 사용 방법을 제공합니다. 5. 부록 액세서리 옵션을 소개하고 부가적인 정보를 제공합니다. 설명서 참고 사항 본 설명서에는 노트북 PC를 사용시 안전하고 완벽한 작업을 위한 참고 사항과 경고 사항이 짙은 글씨로 표기되어 있습니다.
1 노트북 PC 소개 안전 예방 수칙 다음의 안전 예방 조치는 노트북 PC의 수명을 늘리기 위함이며, 다음의 모든 주의사항을 반 드시 지켜 주시기 바랍니다. 본 사용자 설명서에 기술되지 않은 사항에 대해서는 인증된 서 비스 센터에 문의해 주십시오. 손상된 전원 코드나 액세서리 및 다른 주변 기기들의 사용을 삼가해 주시고 희석제, 벤젠, 기타 다른 화학 제품 같은 강한 용액이 본체 면에 직접 닿지 않 도록 해주십시오. 중요! 제품을 청소하기 전에 AC 전원과 배터리 팩을 분리해 주십시오. 비 마모성 세제액 을 따뜻한 물에 풀어 넣고 깨끗한 섬유 스폰지 또는 젖은 세무천에 몇 방울 적셔서 노트북 PC를 닦은 후, 마른천으로 남은 물기를 제거해 주십시오. 평평하지 않거나 불안정한 장소에 놓지 마십시오. 만일 외관이 손 상되었다면 수리를 받아 주십시오. 노트북 PC 위에 물건을 놓거나 떨 어 뜨리지 마십시오. 노트북 PC 안 에 이물질을 넣지 마십시오. LCD 패널을 누르거나 만지지 마십 시오.
1 노트북 PC 소개 운반 시 주의사항 노트북 PC를 운반할 경우, 전원을 끈 후, 커넥터의 손상을 방지하기 위해 모든 외부 주변 장 치를 분리해 주십시오. 전원을 켠 채로 이동할 경우, 하드디스크 드라이브 헤드로 인해 하드 디스크의 표면이 긁힐 수 있습니다. 그러므로 전원이 켜져 있는 동안에는 노트북 PC의 이동 을 삼가하여 주십시오. 키보드와 디스플레이 패널을 보호하기 위해 상판의 덮개가 닫혀 있는 지 확인해 주십시오.� 주의: 노트북 PC의 표면은 올바르게 관리하지 않을 경우, 쉽게 더러워 집니다. 노트북 PC 운반 시, 표면의 긇힘이나 훼손 등에 주의해 주십시오. 노트북 PC 커버 먼지, 물, 충격 및 긁힘을 방지하기 위해, 옵션으로 제공되는 휴대용 케이스를 구 입할 수 있습니다. 배터리 충전 장거리 여행 등으로 배터리를 이용해 노트북 PC를 사용할 경우, 배터리팩과 여분의 배터리 팩을 충전시켜 준비해 주십시오. 전원 어댑터를 컴퓨터에 연결시켜 배터리 팩을 충전시켜 주 십시오.
1 노트북 PC 소개 노트북 PC 준비 다음은 노트북 PC를 처음 사용하기 위한 간단한 절차이며, 본 노트북 PC 사용에 관한 자세 한 정보는 사용자 설명서 후반부를 참고해 주십시오. 2. AC 전원 어댑터 연결 1. 배터리 팩 장착 4 2 3 1 5 3. 디스플레이 패널 열기 중요! 노트북을 열 때, 힌지가 부러질 수 있 으므로 무리하게 힘을 주어 열지 마십시오. 상판만 잡은 상태에서 노트북 PC를 들지 마십시오! 2 3 1 4. 노트북 PC 전원 켜기 전원 스위치로 노트북 PC의 전원을 켜거나 끌 수 있거나, 노트북 PC를 대기 모드 또는 최대 절전 모드로 전환할 수 있습니다. 전원 스위치의 작동은 Windows 제어판 > 전원 옵 션 > 시스템 설정에서 바꿀 수 있습니다.
1 10 노트북 PC 소개
2. 노트북 PC 기본 구성 노트북 PC 부분별 설명 본 설명서내에 보여지는 그림과 노트북에서의 실제 모습은 차이가 있을 수 있습니다. 노트 북 PC의 내용이 설명서의 그림에 우선합니다. 참고: 본 설명서에 사용된 사진과 아이콘은 사용자의 이해를 돕기 위한 이미지이며, 제품 자체에서의 실제 모습과 다를 수 있습니다.
2 노트북 PC 기본 구성 상판부 노트북 PC 상판부의 구성 요소를 확인하려면 아래의 그림을 참고해 주십시오. 참고: 키보드의 실제 모습은 구입 지역에 따라 다를 수 있습니다.
노트북 PC 기본 구성 1 카메라 표시등 2 카메라 (일부 모델) 2 카메라 지시등은 내장된 카메라가 사용중인지의 여부를 알려줍니다. 카메라는 지원 소프 트웨어에 의해 자동으로 활성화됩니다. 내장 카메라를 이용해 사진 촬영, 비디오 녹화는 물론, 화상 회의 및 기타 인터랙티 브 애플리케이션과 호환이 가능합니다. 3 마이크로 폰 (내장) 탑재된 모노 마이크로 폰을 이용해 화상 회의, 음성 나레이션 및 간단한 음성 녹음을 할 수 있습니다. 4 빛 센서 (일부 모델) 5 디스플레이 패널 6 상태 표시등 (상단부) 빛 센서는 사용 환경의 빛 상태를 측정하고 이 값에 따라 LCD 디스플레이의 휘도를 설정 합니다. 고화질 플랫 패널을 탑재하여 해로운 전파 또는 깜박임 없이 데스크탑 모니터와 같은 탁월한 화면을 제공하여 눈을 편하게 해 줍니다. 화학 용액이 묻지 않은(필 요에 따라 깨끗한 물) 부드러운 천을 이용해 디스플레이 패널을 닦아 주십시오.
2 노트북 PC 기본 구성 10 키보드 11 터치패드와 버튼 12 지문 인식기 (일부 모델) 키보드는 편안한 키감(키가 눌리는 깊이)을 제공하는 풀 사이즈의 키와 양손의 편안함을 제공하는 팜레스트로 이루어져 있습니다. 2개의 Winodws 키가 제공되 어 Windows 운영체제를 보다 손쉽게 이용할 수 있습니다. 터치패드와 터치패드의 버튼은 데스크탑의 마우스와 같은 기능을 합니다. 터치패드 유틸리티를 설치하면 스크롤링 기능을 사용할 수 있으며, Winodws와 인터넷 탐색 을 보다 손쉽게 이용할 수 있습니다. 지문 인식기는 지문을 ID 키로 사용하여 보안된 소프트웨어의 사용을 가능하게 해줍니다. 13 상태 표시등 (전면부) 상태 표시등은 하드웨어/소프트웨어의 여러 상태를 나타냅니다. 제 3장을 참고하십시오.
2 노트북 PC 기본 구성 하판부 노트북 PC 하판부의 구성 요소를 확인하려면 아래의 그림을 참고해 주십시오. 참고: 하판부의 구성은 모델에 따라 다를 수 있습니다. 참고: 배터리 팩의 크기는 모델에 따라 다를 수 있습니다. 1 2 3 4 경고! 노트북 PC의 하판부는 매우 뜨겁습니다. 노트북 PC가 작동 중이거나 전원을 차단 한 지 얼마되지 않은 상태에서는 발열이 심하므로 주의해 주십시오. 충전 또는 작동 중에 는 고온의 상태가 유지되므로 노트북 PC를 무릎이나 신체의 일부분과 접촉해 상해를 입 지 않도록 주의해 주십시오.
2 노트북 PC 기본 구성 1 배터리 팩 2 배터리 잠금 장치 - 스프링 3 메모리 (RAM) 구획 AC 전원을 연결할 경우, 배터리 팩은 자동으로 충전되며, AC 전원이 연결되어 있지 않은 경우, 배터리 팩이 노트북 PC에 전원을 공급해 노트북 PC를 가까운 곳에 이동 해 사용할 경우, 이용됩니다. 배터리 수명은 사용 방법과 노트북 PC의 배터리 용량 에 따라 다릅니다. 배터리 팩은 더 분해할 수 없으며 배터리 팩을 교체하려면 단일 유 닛으로 교체해야 합니다. 배터리 팩은 스프링 배터리 잠금 장치로 안전하게 고정됩니다. 배터리 팩을 장착할 경 우, 스프링 배터리 잠금 장치는 자동으로 배터리 팩을 고정시킵니다. 배터리 팩 제거 시, 스프링 배터리 잠금 장치는 잠금 해제 위치에 고정되어 있어야 합니다. 추가 메모리를 슬롯에 설치할 수 있습니다. 추가 메모리를 설치하면 하드디스크 액 세스를 줄여 시스템 성능을 향상시킬 수 있습니다.
노트북 PC 기본 구성 2 좌측면 노트북 PC 좌측면의 구성 요소를 확인하려면 아래의 그림을 참고해 주십시오. 1 2 3 1 전원 (DC) 입력 2 LAN 포트 3 디스플레이 (모니터) 출력 4 4 5 6 7 8 9 기본으로 제공된 전원 어댑터는 AC 전원을 DC전원으로 바꾸어 주는 역할을 합니다. 이 잭을 통해 공급된 전력은 노트북 PC에 전원을 공급하고, 내장된 배터리 팩을 충전 시켜 줍니다. 노트북 PC와 배터리 팩의 손상을 방지하기 위해 향상 기본 제공된 전원 어댑터만 사용하십시오. (주의: 사용시 가열될 수 있으므로 어댑터를 물건으 로 가리지 마시고, 신체에서 멀리 떨어진 곳에서 사용하십시오.) RJ-11 모뎀 포트보다 크기가 큰 RJ-45 LAN 포트는 로컬 네트워크 연결 시 표 준형 이더넷 케이블을 사용합니다. 추가 어댑터를 사용할 필요가 없어 더욱 편 안한 작업 환경을 제공합니다.
2 5 2.0 노트북 PC 기본 구성 USB 포트 (2.0/1.1) 범용 직렬 버스(USB)는 키보드, 포인팅 장치, 비디오 카메라, 모뎀, 하드디스크 드라이버, 프린터, 모니터, 스캐너 등과 같은 수 많은 USB 2.0(480Mbits/초) 또는 USB 1.1(12Mbits/초) 장치의 규격입니다. USB는 USB 키보드나 최신 모니터, 허브 와 같은 많은 장치들을 한 대의 컴퓨터에서 동시에 사용할 수 있도록 해줍니다. USB는 핫 스와퍼블 기능을 지원하여 컴퓨터를 재시작 하지 않고도 외부 장치들을 연결하거나 연결 을 끊을 수 있습니다. 6 안테나 입력 (일부 모델) 7 IEEE1394 포트 (일부 모델) 하이브리드 TV 모델: 안테나 입력은 TV 또는 FM 라디오(일부 모델)의 전파 수신을 위해 사용할 수 있으며, 제공된 디지털 TV/FM 안테나와 함께 사용하 거나 일반 TV 시청 서비스를 입력 받을 수 있습니다.
2 노트북 PC 기본 구성 우측면 노트북 PC 우측면의 구성 요소를 확인하려면 아래의 그림을 참고해 주십시오. 1 1 옵티컬 드라이브 2 옵티컬 드라이브 전자 버튼 2 3 4 5 노트북 PC는 모델에 따라 서로 다른 옵티컬 드라이브를 포함하고 있습니다. 노트북 PC의 옵티컬 드라이브는 모델에 따라 CD 및/또는 DVD를 지원할 수도 있으며, CD-R 또는 RW의 기록 기능을 지원할 수도 있습니다. 자세한 사항은 각 모델에 따른 세부 사양을 확인해 주십시오. 옵티컬 드라이브는 전자식 꺼내기 버튼을 통해 트레이를 엽니다. 사용자는 또한 소프트웨어 플레이어 또는 Windows의 내 컴퓨터에서 마우스 오른쪽 버튼을 클릭해 꺼내기 버튼을 선택 할 수도 있습니다. 또한 옵티컬 드라이브의 동작 표시등 기능을 통해 옵티컬 드라이버가 데 이터를 전송 중임을 알려줍니다. 이 표시등은 전송되는 데이터의 크기에 따라 깜박이는 비율 이 달라집니다.
2 노트북 PC 기본 구성 후면부 노트북 PC 후면부의 구성 요소를 확인하려면 아래의 그림을 참고해 주십시오. 1 공기 배출구 1 공기 배출구는 노트북 PC의 뜨거운 공기를 배출하고, 차가운 공기를 흡입합니다. 중요! 종이, 책, 옷, 케이블 또는 다른 물체가 공기 배출구를 막지 않았는지 확 인하십시오. 장치가 과열될 수 있습니다.
노트북 PC 기본 구성 2 전면부 노트북 PC 전면부의 구성 요소를 확인하려면 아래의 그림을 참고해 주십시오. 1 1 2 3 4 5 무선 스위치 내장된 무선 LAN과 Bluetooth (일부 모델)의 사용 여부를 선택합니다. 사용을 선택하면 무선 상태 표시등에 불이 들어옵니다. 이 기능을 사용하려면 Windows 소프트웨어 설정이 필요합니다. 2 Combo SPDIF 출력 잭 이 잭을 통해 디지털 오디오 출력을 위한 SPDIF(Sony/Philips Digital Interface) 호환 장치들과의 연결이 가능합니다. 이 기능을 이용하면, 노트북 PC를 Hi-Fi 홈 엔터테인먼트 시스템으로 이용할 수 있습니다. 헤드폰 출력 잭 스테레오 헤드폰 잭(1/8 인치)은 노트북 PC의 오디오 출력 신호를 전원이 포함된 스피 커 또는 헤드폰과 연결하는데 사용됩니다. 이 잭을 사용하면 내장 스피커는 자동으로 비활성화됩니다.
2 22 노트북 PC 기본 구성
3. 노트북 PC 시작 AC 전원 사용 배터리 전원 사용 노트북 PC 시스템 시작 배터리 전원 확인 전원 옵션 전원 관리 모드 키보드 특별 기능 스위치 및 상태 표시등 본 설명서내에 보여지는 그림과 노트북에서의 실제 모습은 차이가 있을 수 있습니다. 노트 북 PC의 내용이 설명서의 그림에 우선합니다. 참고: 본 설명서에 사용된 사진과 아이콘은 사용자의 이해를 돕기 위한 이미지이며, 제품 자체에서의 실제 모습과 다를 수 있습니다.
3 노트북 PC 시작 전원 시스템 AC 전원 사용 노트북 PC는 전원 어댑터와 배터리 전원 시 스템으로 전원을 사용합니다. 전원 어댑터는 전기 콘센트의 DC 전원을 노트북에 필요한 AC 전원으로 전환합니다. 노트북 PC에는 범 용 AC-DC 어댑터가 기본으로 제공되어 설 정 스위치나 전원 컨버터를 사용하지 않고도 2 3 220V-240V 뿐만 아니라 100V-120V를 모 두 사용할 수 있습니다. 일부 국가에서는 규 1 격이 다른 US 표준형 AC 전원 코드를 지원 하는 어댑터를 사용해야 합니다. 하지만 대 부분의 호텔에서는 다른 전원 코드와 전압을 지원하는 범용 콘센트를 제공합니다. 일부 국각에 전원 어댑터를 가져 가시려면, 그나라에 방문 경험있는 여행자에게 AC 콘센트의 전 압을 문의해 보시는 것도 하나의 방법입니다. 팁: 거의 대부분의 국가에서는 노트북 PC 사용자가 손쉽게 구입할 수 있는 노트북 PC의 여행용 킷을 판매 하고 있습니다.
3 노트북 PC 시작 배터리 전원 사용 노트북 PC는 탈착이 가능한 배터리 팩을 사용합니다. 배터리 팩은 여러 개의 셀들을 결합해 하나의 유닛으로 설계되어 있습니다. 완충된 배터리 팩은 몇 시간 동안 사용할 수 있지만 배 터리 팩에 사양에 따라 사용 시간이 다릅니다. 또한 BIOS의 전원 관리를 통해 배터리 사용 시간을 연장시킬 수 있으며 추가 배터리 팩은 옵션으로 구입할 수 있습니다. 추가 배터리 팩 구입은 노트북 PC 판매점에 문의해 주십시오. 배터리 팩 장착 및 제거 구입하신 노트북 PC에는 배터리 팩이 장착되어 있지 않을 수도 있습니다. 만약 노트북 PC에 배터리 팩이 장착되어 있지 않다면, 다음의 절차를 따라 배터리 팩을 장착해 주십시오. 중요! ���������������������������������������������� 작업 중인 데이터가 손실 될 수 있으므로, 노트북 PC를 사용 중일 때는 배터리 팩 을 제거하지 않도록 주의해 주십시오.
3 노트북 PC 시작 배터리 관리 재충전할 수 있는 노트북 PC의 배터리 팩은 모두 재충전할 수 있는 횟수에 한계가 있습니다. 온도나 습도와 같은 사용자의 환경과 노트북 PC의 사용 방법에 따라 배터리 팩의 사용 수명 이 달라질 수 있습니다. 최적의 배터리 보관 온도는 5℃~35℃(41°F~95°F)입니다. 또한 노 트북 PC의 내부 온도가 외부 온도보다 높다는 것도 고려해 주십시오. 이 범위 외의 온도에서 사용할 경우에서 사용할 경우, 배터리 수명은 줄어들게 됩니다. 하지만 배터리 팩의 수명은 결국 줄어들 수 밖에 없으므로 배터리가 완전 소모된 경우, 인증된 판매처에서 새 배터리 팩 을 구입해 주십시오. 또한 배터리는 사용 유효 기간이 있으므로, 추가로 미리 구입하는 것은 권장해 드리지 않습니다. 경고! 안전 상의 이유로 배터리를 불 속에 던지지 마십시오. 전기 접촉 및 배터리 를 분해하지 마십시오.
노트북 PC 시작 3 노트북 PC 시스템 시작 노트북 PC에 전원을 공급하면 짧은 비프음이 나오면서 화면에 Power-On 메시지가 나타납 니다. 핫키를 이용해 화면의 밝기를 조절할 수 있으며 만약 시스템의 구성을 설정하거나 수 정하려면, 부팅시 [F2]키를 눌러 BIOS 설정으로 들어가 주십시오. 또한 [Tab]키를 누르면, 표준 부팅 정보를 확인할 수 있는 화면이 나타나며, [ESC]키를 누르면 사용 가능한 드라이 브 중 부팅하고자 하는 드라이브의 메뉴가 화면에 나타납니다. 참고: 부팅하기 전에, 노트북 PC가 켜져 있다면 LCD 패널에 빛이 나타납니다. 이 과정은 노트북 PC의 정상적인 테스트 과정이며 디스플레이 문제가 아닙니다. 중요! 하드디스크의 보호를 위해 노트북 PC를 종료한 후에는 5초가 지난 다음 다시 시작 해 주십시오. 경고! 전원이 켜져 있는 상태에서 노트북 PC를 이동시키거나 닫지 마십시오.
3 노트북 PC 시작 배터리 전원 확인 Windows 작업 표시줄에 있는 전원 아이콘을 클릭하면, 배터리의 잔여량을 확인할 수 있습 니다. 완전히 충전된 배터리 팩은 몇 시간 동안은 별도의 전원을 연결하지 않고도 노트북 PC에 전원을 공급해 줍니다. 하지만 정확한 배터리 사용 가능 시간은 사용하는 절전 기능에 따라 또는 평소 사용자의 작업 습관, CPU, 시스템 메모리 크기, 디스플레이 패널의 크기에 따라 달라질 수 있습니다. 참고: 그림은 참고용입니다. 사용자가 실제 보게되는 화면 은 다를 수 있습니다. 배터리 아이콘 오른쪽 클릭 참고: 만약 배터리 부족 경고 를 무시할 경우, 갑자기 노트북 PC가 대기 모드(STR)로 전환될 수 있습니다. Windows 기본값은 대기 모드(STR) 입니다. 전원 어댑터 연결 없이 배터리 아이 콘 위에 마우스를 올려 놓은 경우. 배터리 아이콘 왼쪽 클릭 전원 어댑터 연결 후 배터리 아이콘 위에 마우스를 올려 놓은 경우.
노트북 PC 시작 3 전원 옵션 전원 스위치로 노트북 PC의 전원을 켜거나 끌 수 있으며, 대기모드 또는 최대절전모드로 전 환할 수 있습니다. 사용자는 Windows 제어판 “전원 옵션”에서 전원 스위치의 기능을 설정 할 수 있습니다. “사용자 전환, 다시 시작, 대기 또는 종료”와 같은 기타 옵션은 잠 금장치 옆에 위치한 화살표를 클릭해 주십시오. 다시 시작 또는 재부팅 운영 시스템의 변경 사항을 적용하기 위해, 시스템을 다시 시작해 야 합니다. 몇몇 설치과정에서는 시스템을 다시 시작할 것인지에 대한 창이 나타납니다. 시스템을 수동으로 다시 시작하려면, 다시 시작을 선택해 주십시오. 중요! 하드디스크의 보호를 위해 노트북 PC를 종료한 후, 시스템을 다시 시작할 경우, 최 소 5초 후에 시스템을 다시 시작해 주십시오.
3 노트북 PC 시작 전원 관리 모드 노트북 PC에는 자동으로 배터리 수명을 최대화 하고, TCO(Total Cost of Ownership)를 줄 일 수 있는 전원 관리 모드 시스템이 있습니다. BIOS 설정 모드의 전원 메뉴에서 이러한 기 능을 설정할 수 있습니다. ACPI 전원 관리 모드는 사용하는 운영체제에 따라 다르며 ACPI 전원 관리 규격은 노트북 PC 작업 시, 최대한 전력 소비를 줄여 가능한 전기를 적게 사용하 도록 도와줍니다. 절전 & 최대 절전 모드 전원 관리 설정은 Windows > 제어판 > 전원 옵션에서 찾을 수 있습니다. 시스템 설정에서 사용자는 디스플레이 패널 닫힘에 “절전/최대절전” 또는 “종료”를 선택할 수 있으며, 또한 전원 버 튼을 누를 수 있습니다. “절전” 및 “최대 절전”모드는 노트북 PC를 사용하지 않을 경우, 일부 기능을 종료함으로써 전원을 절 약할 수 있습니다. 다시 작업을 시작할 경우, 마지막 작업 상태 화면이 나타납니다.
노트북 PC 시작 3 키보드 특별 기능 컬러 핫 키 다음은 노트북 PC 키보드의 색깔로 표시된 핫 키에 대한 설명입니다. 색깔로 표시된 핫 키는 [Fn]을 누른 상태에서 버튼을 누르면 작동합 니다. 참고: 핫키의 배치는 모델에 따라 다를 수 있습니다. 하지만 기본적인 기능은 동일합니다. 다음에 표시된 아이콘을 참고해 주십시오. “Zz” 아이콘 (F1): 대기 모드(전원 관리에서 설정한 절전 모드에 따라 Save-toRAM 또는 Save-to-Disk)를 작동시킵니다. 라디오 타워 아이콘 (F2): (무선 모델에만 적용) 무선 소프트웨어 프로그램을 실행시키거나 내장 무선 LAN 또는 Bluetooth(일부 모델) 기능 사용 여부를 선택 시 사용합니다. 이 기능을 사용하려면 해당하는 무선 상태 표시등에 불이 들어옵니다. 무선 LAN과 Bluetooth를 사용하려면 Windows 소프트웨어 설정이 필요합니다. 밝기 감소 (작은 태양) 아이콘 (F5): 화면의 밝기를 어둡게 합니다.
3 노트북 PC 시작 컬러 핫 키 (계속) Scr Lk (Num LK): 키보드를 이용한 스크롤 기능의 사용 여부를 선택합니 다. 키보드의 일부분을 셀 스크롤 기능으로 고정하여 사용할 수 있습니다. Fn+C: “Splendid Video Intelligent Technology” 기능을 켜거나 끌 수 있습니다. 이 기능은 녹색, 빨강색, 검정색, 파랑색의 콘트라스트, 명 도, 스킨 톤, 색채를 각각 향상시켜주기 위해 다양한 디스플레이 향상 모드를 사용합니 다. on-screen display (OSD)를 통해 현재 사용 중인 모드를 확인할 수 있습니다. Fn+V: “Life Frame” 소프트웨어를 실행합니다. Fn+A: 빛 센서의 사용 여부를 선택 가능합니다. Power4Gear eXtreme (Fn+Space Bar): 여 러 전원 절약 모드 중 하나를 선택할 수 있습 니다. 이 전원 절약 모드는 배터리 시간 대비 성능을 최대화하기 위해 노트북 PC의 많은 부분을 제어합니다.
노트북 PC 시작 3 Microsoft Windows 키 다음과 같이 키보드에는 두 개의 특별한 Windows 키가 있습니다. Windows 로고가 그려진 키를 누르면 Windows의 바탕화면 좌측 하단부에 시작 메뉴 가 나타납니다. Windows 메뉴 모양의 그림이 그려진 키를 누르면 속성 메뉴가 나타납니다. 이 키는 마우스 오른쪽 버튼을 클릭한 것과 같은 기능을 수행합니다. 확장 키보드 일부 모델에 한하여 확장 키보드의 사용이 가능합 니다. 확장 키보드는 숫자의 편리한 입력을 위한 전 용 숫자 키패드를 포함하고 있습니다. [Num Lk / Scr Lk]를 이용하여 확장 키패드를 숫자 또는 포인 터 방향 등의 목적으로 사용이 가능합니다. 스프레드 시트 또는 표와 같은 항목 또는 셀 사이의 탐색을 위 해 포인터 방향 키로 사용이 가능합니다.
3 노트북 PC 시작 스위치 및 상태 표시등 스위치 모드 스위치 키 두 종류의 원터치 키가 있습니다. 이 버튼을 눌러 원터치 키의 모드를 변환 가능합니다. 멀티미디어 제어 키 멀티미디어 제어 키를 이용해 멀티미디어 애플리케이션의 편리한 제어가 가능하며, 방향키 로도 동작합니다. 자세한 정보는 이 장의 마지막 부분을 참고해 주십시오. Power4Gear eXtreme 키 Power4Gear eXtreme 버튼을 누르면 다양한 절전 모드를 이용해 전력을 절약할 수 있는 Power4 Gear 기능을 사 용할 수 있습니다. 각 절전 모드들은 노트북 PC의 배터리 대비 성능을 최대화 하기 위해 많은 부분을 관리합니다. 전원 어댑터 사용 또는 제거 시, 시 스템은 자동으로 AC 모드와 배터리 모드를 전환됩니다. OSD (on-screen display) 를 통해 현재 사용 중인 모드를 확인할 수 있습니다.
노트북 PC 시작 3 스위치 및 상태 표시등 (계속) 스위치 전원 스위치 전원 스위치는 노트북 PC의 전원을 켜거나 끄는 기능을 하며, 또한 노트북 PC를 절전 또는 최대 절전 모드로 전환합니다. 전원 스위치의 실제 기능은 Windows 제어판 “전원 옵션”에서 설정이 가능합니다. Express Gate 키 이 버튼을 누르면 Express Gate를 실행합니다. 자세한 정보는 Express Gate 사용자 설명서 를 참고해 주십시오. 이 키는 노트북 PC가 Windows 운영체제 환경에 있을 경우 기능하지 않습니다.
3 노트북 PC 시작 스위치 및 상태 표시등 (계속) 상태 표시등 전면부 전원 표시등 노트북 PC의 전원이 켜지면, 불이 켜지며, 대기(절전) 모드에서는 이 표시등의 불이 깜박이게 됩니다. 노트북 PC의 전원이 꺼지거나, 최대 절전 모드(하이버네이션)에서 는 이 표시등의 불이 사라집니다. 배터리 충전 표시등 배터리 충전 표시등은 배터리의 충전 상태를 나타냅니다.: 켜짐: AC 전원이 연결되어 있을 경우, 노트북 PC의 배터리가 충전되고 있는 상태입니다. 꺼짐: 노트북 PC의 배터리가 완전 충전되거나 완전 방전된 상태입니다. 깜박거림: 배터리 전력이 10% 이하이며, AC 전원이 연결되지 않은 상태입니다. 드라이브 동작 표시등 노트북 PC가 하드디스크와 같은 저장 장치에 액세스하고 있는 상태를 나타냅니 다. 액세스 속도에 비례하여 표시등이 깜빡입니다. 무선 표시등 이 표시등은 무선 LAN 및/또는 Bluetooth 기능을 내장하고 있는 모델에만 적 용됩니다.
노트북 PC 시작 3 스위치 및 상태 표시등 (계속) 상태 표시등 (계속) 상판부 공기 이온화 키 공기 이온화 기능이 활성화 상태인지 보여줍니다. 숫자 잠금 표시등 이 곳에 불이 들어오면, [Num Lk]이 활성화되었음을 의미합니다. 숫자 잠금은 문자 키보드의 일부분을 숫자로 동작하도록 하여 편리하게 숫자 데이터를 입 력할 수 있습니다. 대문자 잠금 표시등 [Caps Lock] 기능이 작동하고 있을 때 표시등에 불이 들어옵니다. 이 기능이 실행되고 있을 때는 문자들이 대문자로 표시되고, 기능이 작동하지 않을 때는 소문자로 표시됩니다.
3 노트북 PC 시작 멀티미디어 제어 키 (일부 모델) 멀티미디어 제어 키를 이용해 멀티미디어 애플리케이션을 편리하게 제어할 수 있습니다. 아 래에 노트북 PC에서 Windows Media Player를 실행할 경우에 사용되는 제어 키에 대해 설 명합니다. 기타 멀티미디어 애플리케이션을 사용할 경우 결과 역시 달라집니다. 참고: 일부 제어 키 기능은 노트북 PC 모델에 따라 달라집니다. [Fn] 키와 방향키의 조합을 이용하여 CD 제어 기능을 사용할 수 있습니다. CD 재생/일시 정지 CD 정지 상태에서 CD 재생을 시작함. CD 재생 상태에서 CD 재생을 일시 정지함. CD Stop CD 정지 상태에서: CD 트레이를 꺼냅니다. CD 재생 상태에서: CD의 재생을 정지합니다. CD 이전 트랙으로 돌아감 (되감기) & 오디오 볼륨 감소 CD 재생 중에, 이 버튼은 두 가지 기능을 가집니다: 트랙: 한 번 누르면, 현재 트랙을 다시 재생합니다. 두 번 누르면, 이전 트랙으로 넘어갑니다.
4. 노트북 PC 사용 포인팅 장치 저장 장치 확장 카드 옵티컬 드라이브 플래시 메모리 카드 리더 하드디스크 드라이브 메모리 (RAM) 연결 모뎀 연결 (일부 모델) 네트워크 연결 무선 LAN 연결 (일부 모델) Bluetooth 무선 연결 (일부 모델) 안테나 연결 (일부 모델) TPM (Trusted Platform Module) (일부 모델) 지문 인식기 (일부 모델) 3G Watcher (지역에 따라 일부 모델에 적용) 본 설명서내에 보여지는 그림과 노트북에서의 실제 그림은 차이가 있을 수 있습니다. 노트 북 PC의 내용이 설명서의 그림에 우선합니다. 참고: 본 설명서에 사용된 사진과 아이콘은 사용자의 이해를 돕기 위한 이미지이며, 제품 자체에서의 실제 모습과 다를 수 있습니다.
4 노트북 PC 사용 포인팅 장치 노트북 PC에 탑재된 터치패드 포인팅 장치는 총 2개 내지 3개의 버튼으로 이루어져 있으며, PS/2 마우스 스크롤 기능을 지원합니다. 터치 패드는 압력에 민감하지만, 유동적인 장치가 아니므로 기계적인 고장이 적습니다. 몇몇 어 플리케이션 소프트웨어에서는 장치 드라이버 를 설치해야 사용할 수 있습니다. 포인터 이동 스크롤 오른쪽 클릭 중요! 터치패드 사용 시, 손 대신에 다른 물 체를 사용하면 터치패드 표면이 손상될 수 있습니다. 지문 인식기 왼쪽 클릭 터치패드 사용하기 손가락 끝으로 가볍게 건드려 터치패드를 조 작할 수 있습니다. 터치패드는 전기적 센서로 작동하기 때문에, 사용자의 손 외에 다른 물 체로 작동시키지 마십시오. 터치패드의 주요 기능은 데스크탑의 표준형 마우스와 달리 손 가락을 이용하여 포인터를 움직이거나 화면 에 보이는 아이템을 선택하는 것입니다. 다음 은 올바른 터치패드 사용 방법을 나타낸 그림 입니다.
노트북 PC 사용 4 그림으로 본 터치패드 사용 방법 버튼 클릭/탭핑 - 포인터를 사용하려는 파일 혹은 폴더에 올려 놓고, 다음 그림과 같이 왼쪽 버튼을 누르거나, 터치패드를 가볍게 탭핑해 주시면, 선택된 파일이나 폴더의 색깔이 바뀝니 다. 아래의 두 동작은 동일한 결과를 만듭니다. 탭핑 클릭 가볍게 터치패드를 쳐 주십시오. 왼쪽 버튼을 눌렀다 떼어 주십시오. 더블 클릭/더블 탭핑 - 이 기능은 사용자가 선택한 아이콘으로 프로그램을 실행시키는 일반 적인 기술입니다. 사용자가 실행하고자 하는 아이콘 위로 포인터를 이동하여 왼쪽 버튼을 클 릭하거나 터치패드를 두 번 빠르게 쳐 주시면 됩니다. 그러면 시스템은 그 프로그램을 실행시 킵니다. 만약 클릭이나 탭핑의 속도가 느리면, 작업은 실행되지 않습니다. Windows 제어판의 “마우스” 항목에서 더블 클릭 속도를 설정할 수 있습니다 아래의 두 동작은 동일한 결과를 만 듭니다. 더블 클릭 더블 탭핑 가볍게 터치패드를 두 번 쳐 주십시오.
4 노트북 PC 사용 터치패드 관리 요령 터치패드는 압력에 민감하게 반응합니다. 만약 제대로 관리하지 않은면, 쉽게 손상될 수 있 습니다. 다음의 주의사항을 지켜주십시오. • • • • 터치패드가 먼지, 액체, 기름 등에 오염되지 않도록 해주십시오. 젖은 손이나, 더러운 상태의 손으로 터치패드를 만지지 마십시오. 터치패드나 터치패드 버튼 위에 무거운 물체를 올려 놓지 마십시오. 손톱이나 딱딱한 물체로 터치패드 표면을 긁지 마십시오. 참고: 터치패드는 움직임에 반응하는 것이지 힘에 반응하는 것이 아닙니다. 터치패드 표 면을 너무 세게 치지 마십시오. 터치패드는 가벼운 압력에 가장 잘 반응합니다. 자동 터치패드 비활성화 기능 Windows는 외장 USB 마우스가 연결되면 자동으로 노트북 PC의 터치패드 기능을 중지합니 다. 이 기능은 일반적으로 꺼져 있지만, 이 기능을 사용하려면 Windows 제어판 > 마우스 속 성 > 장치 설정에서 기능을 활성화해 주십시오.
노트북 PC 사용 4 저장 장치 노트북 PC의 탑재된 저장 장치를 이용해 문서, 사진, 기타 파일을 다양한 데이터 저장 장치 에서 읽거나 쓰고, 저장할 수 있습니다. 본 노트북 PC는 다음과 같은 저장 장치를 포함하고 있습니다: • 확장 카드 • • • 옵티컬 드라이브 플래시 메모리 리더 하드디스크 드라이브 확장 카드 26핀 Express 카드 슬롯은 하나의 ExpressCard/34mm 또는 하나의 ExpressCard/54mm 확장카드를 지원합니다. 이 새로운 인터페이스는 PC 카드 슬롯에 사용된 느린 패레럴 버스 대신에 USB 2.0과 PCI Express를 사용하여 더욱 빠른 속도를 제공해 줍니다. (기존의 PCMCIA 카드와 호환되지 않습니다.) 확장 카드 설치 카드를 넣을 때, 수평을 유 지해 주십시오. 두 가지 종류의 크 기가 있습니다. 1. ������������ 만약 슬롯에 플라스틱 ���������� 보호대가 있다면 아 3.
4 노트북 PC 사용 플래시 메모리 카드 홀더 (일부 모델) 노트북 PC에 포함된 모형 확장 카드 슬롯은 플래시 메모리 카드의 컨덕터를 보호하기 위한 메모리 카드의 보관함으로 사용이 가능합니다. 카드 보관함은 메모리 카드의 분실 가능성을 줄여주며, 플래시 메모리 카드 내의 중요한 데이터의 손상 가능성을 최소한으로 줄여줍니다. 메모리 카드 홀더에 최대 2개의 SD 또는 MS 타입의 메모리 카드를 보관할 수 있습니다. 사용자는 두 개의 SD 카드 또는 하나의 SD 카드와 하나의 MS 카드를 보관할 수 있습니다.
노트북 PC 사용 4 옵티컬 드라이브 옵티컬 디스크 삽입 2 1 1. 노트북 PC의 전원이 켜져 있을 때, 꺼내기 버튼을 누르면 트레이가 약간 열립니다. 2. 부드럽게 드라이브의 전면 패널을 잡고 트 레이를 완전히 꺼내 주십시오. CD 드라이 브 렌즈와 기타 장치가 손에 닿지 않게 해 주시고, 드라이브 트레이 하판부에 다른 물 체가 끼어있지 않은지 확인해 주십시오. -R CD 2 3. 디스크의 모서리를 잡고 프린트 되어 있 4. 천천히 드라이브 트레이를 다시 장착시켜 는 부분이 위로 가도록 하여주십시오. 디 주십시오. 디스크 목록의 읽기가 끝나면 스크가 허브에 정확히 끼어지도록 디스 디스크를 사용할1수 있습니다. 크의 가운데 부분을 눌러 주십시오. 디 스크가 올바르게 장착되면 허브는 디스 크보다 조금 더 높이 올라옵니다. 참고: 데이터 읽기가 작동되고 있을 때 심한 소음이 들릴 수 있는데, 이것은 정상입니다.
4 노트북 PC 사용 옵티컬 드라이브 (계속) 옵티컬 디스크 제거 긴급 꺼내기 2 1 모델에 따라 실제 위치 가 다를 수 있습니다. CD -R 트레이를 연 후 디스크 끝을 잡고 조심스 럽게 위로 들어올려 허브에서 제거해 주십 시오. 긴급 꺼내기 버튼은 옵티컬 드라이브에 위 치하고 있으며, 전자 꺼내기 기능이 작동하 지 않을 때 사용합니다. 전자 버튼 대신에 긴급 꺼내기 기능을 사용하지 마십시오. 참고: 같은 장소에 위치한 상태 표시등을 찌 르지 않도록 조심해 주십시오. 옵티컬 드라이브 사용하기 옵티컬 디스크와 드라이브 장치는 정밀한 장비이므로 주의를 기울여 사용하시고, 사용시 안전 수칙을 반드시 준수해 주십시오. 노트북 PC의 옵티컬 드라이브는 데스크탑 옵티컬 드라이브 와 달리 중앙 허브에 CD를 넣는 방식을 사용하므로 CD를 삽입 할 때, CD가 중앙 허브에 올바 르게 끼워졌는지 확인해 주십시오. 그렇지 않으면 CD에 손상을 줄 수 있습니다.
노트북 PC 사용 4 플래시 메모리 카드 리더 일반적으로 PCMCIA 메모리 카드 리더는 디지털 카메라, MP3 플레이어, 휴대폰 및 PDA와 같은 장치의 메모리 카드를 사용하기 위해 별도로 구입하셔야 합니다. 이 노트북 PC는 아래 의 그림과 같이 여러 종류의 플래시 메모리 카드를 인식할 수 있는 내장형 메모리 카드 리더 가 탑재되어 있습니다.내장형 카드 리더는 높은 대역폭을 지원하는 PCI 버스를 사용해 기타 다른 멀티 리더에 비해 편리할뿐만 아니라 훨씬 빠른 속도를 지원합니다. 중요! 플래시 메모리 카드는 노트북 PC 모델과 플래시 메모리 카드 사양에 따라 호환성이 달라집니다. 플래시 메모리 사양은 사전 통보 없이 변경될 수 있습니다.
4 노트북 PC 사용 하드디스크 드라이브 하드디스크 드라이브는 플로피 디스크 드라이브나 옵티컬 드라이브에 비 해 훨씬 더 빠른 작업 수행 능력을 가지고 있습니다. 본 노트북 PC는 탈 착 가능한 하드디스크 드라이브가 탑재되어 있습니다. 탑재된 하드디스 크 드라이브는 문제점을 스스로 인식하는 S.M.A.R.T. (Self Monitoring and Reporting Technology) 기술이 적용되어 있습니다. 교체 또는 업그레이드를 할 경우에는, 인증된 서비스 센터 또는 판매 대리점에 문의해 주십시오. 중요! 노트북 PC를 함부로 다루면 하드디스크에 손상을 줄 수 있습니다. 항상 노트북 PC를 주의해서 다뤄 주시고, 전기, 자기가 강한 근처에 노트북 PC를 두지 마십시오. 하드디스크 드라이브는 가장 민감한 부품으로, 강한 진동이나 충격에 쉽게 파손될 수 있습니다.
노트북 PC 사용 4 하드디스크 드라이브 설치하기: 1 2 49
4 노트북 PC 사용 메모리 (RAM) 추가 메모리는 하드 디스크 접속을 낮춤으로써 어플리케이션의 성능을 향상시켜 줍니다.������������������������������� 노트북 PC의 메모리 업그레이드에 관한 정보는 인증 서 비스 센터를 방문해 확인해 주십시오. 해당 노트북 PC의 인증된 대리점에 서 구입한 확장 모듈만이 최대 호환성과 안정성을 보장받을 수 있습니다. 이 그림은 단지 예시일 뿐입니다. BIOS는 자동으로 시스템 내의 메모리를 감지하고, POST 모드에서 CMOS를 구성합니 다. 메모리 설치 후, 추가의 하드웨어 또는 소프트웨어(BIOS 포함)를 구성할 필요가 없습니다. 경고! 하드디스크 커버를 열기 전 에 연결된 모든 주변 장치, 전화 또는 통신 선과 전원 커넥터(외장 전원 공급 장치, 배터리 팩 등)의 연결을 해제해 주십시오. 메모리 카드 설치하기: 메모리 카드 제거하기: 3 3 (그림은 단지 예시일 뿐입니다.) 50 (그림은 단지 예시일 뿐입니다.
노트북 PC 사용 4 연결 네트워크는 추후 업그레이드가 불가능합니다. 하지만 구입 후, 네트워크를 확장 카드 형 식으로 설치가 가능합니다. 네트워크 연결 양 끝에 RJ-45 커넥터가 있는 네트워크 케이블을 이용해 한쪽은 노트북 PC의 모뎀/네트워크 포트와 다른 한쪽은 허브/스위치를 연결해 주십시오. 100 BASE-TX / 1000 BASE-T 속도로 네트워크에 연결하려면 카테고리 5 규격의 네트워크 케이블(트위스트 페어)이나 고급 케이블 (카테고리 3은 사용 불가)을 사용해 주십시오. 만약 100/1000Mbps의 속도로 연결하려면, 100 BASE-TX / 1000 BASE-T 허브 (BASE-T4 허브 사용 불가)에 연결해야 합니다. 10Base-T 속 도로 네트워크에 연결하려면 카테고리 3, 4, 5 트위스트 페어 케이블을 사용해 주십시오. 본 노 트북은 10/100 Mbps Full-Duplex 모드를 지원하지만 “Duplex” 모드가 지원되는 스위칭 허브 를 사용해야 합니다.
4 52 노트북 PC 사용
노트북 PC 사용 4 무선 LAN 연결 (일부 모델) 내장형 무선 LAN은 무선 이더넷 어뎁터를 이용하여 간편하게 사용할 수 있습니다. 무선 LAN에 표준으로 쓰이는 IEEE 802.11을 적용하면 내장된 무선 LAN은 2.4 GHz 주파수에 서 DSSS(Direct Sequence Spread Spectrum)과 OFDM(Orthogonal Frequency Division Multiplexing) 기술을 이용하여, 빠른 데이터 전송속도를 제공합니다. 내장형 무선 LAN은 기 존에 쓰이던 IEEE 802.11 무선 규격과도 역호환 됩니다. 내장형 무선 LAN은 기존 사용자가 사용하는 무선 네트워크 구성 또는 미래에 사용하게 될 구성을 클라이언트로부터 AP간의 거리를 최대 40미터까지 가능하게 하는 Infrastructure과 Ad-hoc 모드를 지원하는 클라이언트 어댑터입니다.
4 노트북 PC 사용 Windows 무선 네트워크 연결 네트워크에 연결하기 1. 무선 스위치를 켜 주십시오 (제 3장의 스위치 참고). 54 2. 무선 LAN ON 또는 WLAN & Bluetooth ON이 나타날 때까지 [FN F2]를 반복해서 눌러 주 십시오. 2b. 또는 작업 표시줄의 무선 콘솔 아이콘을 더 블 클릭한 후, 무선 LAN + Bluetooth 또는 Bluetooth를 선택해 주십시오. 3. “연결되지 않음” 네트워크 아이콘이 나타날 것입니다. 4. 네트워크 아이콘을 마우스 오른쪽 클릭한 후, 네트워크에 연결을 선택해 주십시오. 5. 사용 중인 영역에 여러 개의 네트워크가 있 다면 “무선 보기”를 선택해 주십시오. 6. 연결하고자 하는 무선 네트워크를 선택해 주십시오. 7. 연결 시, 비밀번호를 입력해야 할 수도 있습 니다. 8. 연결이 되면, “연결됨” 표시가 나타납니다.
노트북 PC 사용 4 Bluetooth 무선 연결 (일부 모델) Bluetooth 기술이 적용된 노트북 PC는 케이블을 따로 연결하지 않고 다른 노트북 PC, 데스크탑 PC, 휴대폰, PDA와 같은 Bluetooth 지원 장치들과 연결할 수 있습니다.� 참고: 만약 노트북 PC에 Bluetooth 기능이 없다면, USB나 ExpressCard, Bluetooth 모듈 을 연결하여 Bluetooth 기능을 사용할 수 있습니다. Bluetooth 지원 핸드폰 Bluetooth 기능이 지원되는 휴대폰을 이용해 무선 연결을 할 수 있습니다. 휴대 폰에 따라 다르지만, 전화번호 데이터, 사진, 음악 파일 등을 전송하거나 모뎀 기 능으로 이용해 인터넷에 접속할 수도 있습니다. 또한 SMS 서비스도 이용할 수 있습니다.
4 노트북 PC 사용 안테나 연결 (일부 모델) 본 페이지는 TV 튜너 모델의 멀티미디어 연결을 보여줍니다. TV와 라디오 기능 사용은 일부 모델에 장착된 모듈을 필요로 합니다. 중요: 안테나 사용 시, 노트북 PC는 실내에서만 작동해 주십시오. 케이블 연결 유료 텔레비젼 서비스에서 사용하는 동축 케 이블, 지붕에 장착된 안테나 또는 실내에서 사 용하는 “토끼 귀” 모양의 안테나를 케이블 어 댑터에 연결해 주십시오. 케이블 서비스 연결 은 유료 서비스에 따라 아날로그 TV를 수신 할 수 있습니다. 제공된 어댑터는 동축 플러그 가 얇은 노트북 PC에 맞게 연결하는데 필요합 니다. 필요시, NTSC-PAL 어댑터를 사용해 주 십시오. 필요하다면 NTSC-PAL Use an NTSC to PAL 어댑터를 사용해 주 adapter if necessary. 십시오. 중요: 벽지 공동 수신은 ANSI/NFPA 70, NEC (National Electrical Code) Section 820.
노트북 PC 사용 4 TPM (Trusted Platform Module) (일부 모델) TPM(Trusted Platform Module)은 암호화된 키로 컴퓨터를 보호하기 위해 시스템 보드에 장 착된 보안 하드웨어 장치 입니다. 이 기능은 중요한 데이터의 비밀번호와 암호화 키를 보기 위한 해커들의 공격을 차단하기 위한 하드웨어 기반의 솔루션입니다. TPM은 PC나 노트북에 서 더욱 안전하게 어플리케이션을 실행하고 안전한게 자료를 처리하고 통신할 수 있는 성능 을 제공합니다. TPM이 제공하제공하는 암호화 보안 기능들은 다음과 같습니다. 해싱, 랜덤 번호 생성, 불규 칙 키 생성, 불규치 암호화/해독. 더욱 실뢰적이고 안정적인 효과를 제공하는 실리콘 제조 공 정시, 각각의 컴퓨터에 적용된 TPM에 특별 서명 기능이 적용되어 있습니다. 안전한 사용을 위해 각각의 TPM은 사용하기 전에 반드시 사용자 등록을 해야 합니다.
4 노트북 PC 사용 지문 인식기 (일부 모델) 지문 스캐너는 즉각적이면서도 보안된 사용자 인증을 위해 사용됩니다. 아래의 내용은 지문 등록 설정에 관한 절차를 보여줍니다. 58 1. BIOS (부록 참고)에서 TPM이 활성화되면 자동으 로 마법사가 시작됩니다. Next를 눌러 주십시오. 2. “Fingerprints”를 선택하고 Next를 눌러 주십 시오. 3. 다이어그램에서 손가락을 선택하고, 스캐너에 천천히 대십시오. 사용자는 확인을 위해 여러차 례 시도해야 합니다. 4. 문제 발생 소지를 줄이기 위해 최소 두 손가락 이상을 등록해 주십시오.
노트북 PC 사용 4 지문 등록 (일부 모델) (계속) 5. 다이어그램에서 손가락을 선택하고 스캐너에 천천히 대십시오. 사용자는 확인을 위해 여러 번 시도해야 합니다. 문제가 ������������� 일어날 소지를 줄 이기 위해 최소 두 손가락 이상을 등록해 주십 시오. 6. 완료 후, Finish를 클릭해 주십시오. 7. 작업 표시줄의 아이콘에 마우스 오른쪽 버튼을 클릭 하고 “Settings and Options”를 선택해 주십시오. 8. “General Options”과 “Single Sign On”를 선 택하고 Preferences를 구성해 주십시오.
4 노트북 PC 사용 3G Watcher (지역에 따라 일부 모델에 적용) 3G(1) Watcher 소프트웨어 어플리케이션은 사용자의 노트북 PC를 이용해 일반적으로 3G 모 바일 폰에 의해 사용되는 3G 무선 네트워크에 연결할 수 있도록 해줍니다. 연결되면 노트북 PC는 무선 네트워크를 사용하는 것과 같이 인터넷을 이용할 수 있습니다. 본 장에서 설명된 기능은 일부 모델 또는 지역에 따라 해당되지 않을 수도 있습니다. 이 기능이 적용되지 않은 제품의 경우 이 부분을 뛰어 넘어 주십시오. 모바일 SIM 카드 설치하기 2 SIM 카드 구획에 3G 기능을 위한 모바일 SIM 카드를 삽입 가능합니다. 3G Watcher 소프트 웨어를 사용하기 전에 모바일 SIM 카드를 먼 저 삽입해 주십시오. 3 900 1 3G Watcher 소프트웨어 사용하기 바탕 화면에서 3G Watcher 애플리케이션을 찾을 수 있습니다.
노트북 PC 사용 4 3G Watcher (지역에 따라 일부 모델에 적용) 3. 3G 네트워크가 발견되면, Connect을 눌러 무 선 네트워크와 연결하십시오. 4. 연결이 되면 Connect 버튼은 Disconnect로 변경됩니다. 5. 연결이 되면 네트워크 이름과 함께 메시지가 나타납니다. 6. 사용자가 무선 전송 (비행기 내)이 금지된 지 역에 있을 경우 Tools 메뉴를 눌러 Turn Radio Off를 선택할 수 있습니다. 7. radio is turned OFF 상태가 되면, 신호 강도 표시등에 “x” 마크가 표시됩니다.
4 노트북 PC 사용 3G Watcher (지역에 따라 일부 모델에 적용) Watcher 창 메인창의 아이콘 및 표시등 Watcher의 메인창은 상태 정보를 제공하여 사용자가 데이터 연결을 초기화하거나, 감시할 수 있도록 해주며 또한, 전화 통화를 하거나 받을 수 있도록 해줍니다. (3G 모뎀과 서비스 제 공자가 음성을 지원할 경우). 메인창은 아래와 같은 표시등을 사용합니다: 장치 상태 3G 모뎀의 아이콘이 “X”로 나타난다면 Watcher는 3G 모뎀을 검색할 수 없음을 의미합니다. 이는 3G 모뎀이 PC 카드 슬롯 (내장형 모뎀이 아닌 경우)으로 완전히 삽입되지 않았거나 전원이 켜있지 않기 때문입니다. 아래의 지시사항을 따르 면 문제를 해결할 수 있습니다: • 3G 모뎀을 꺼낸후 재설치해 주십시오. • PC에서 WWAN 스위치를 껐다가 다시 켜 주십시오. 신호강도 및 서비스 상태 안테나 옆의 막대가 많을 수록 신호 강도가 증가하며, 최대 다섯개까지 증가합니다.
노트북 PC 사용 3G Watcher 4 (지역에 따라 일부 모델에 적용) 로밍 사용자의 로컬 서비스 제공자가 아닌 다른 네트워크에 연결되며, 로밍 서비스 사 용에 따른 추가 요금이 부과될 수 있습니다. (이 서비스는 사용 불가능할 수 있습니다. ) 새로운 SMS 메시지 아이콘을 클릭하여 SMS 익스프레스 창을 열고, 메시지를 읽으 십시오. SIM의 용량이 가득 차면, 아이콘이 깜빡이거나 붉게 변합니다. (일부 장치에 서만 지원됩니다.) 데이터 전송 모뎀이 네트워크에 연결될 경우, Watcher의 메인창은 전송받았거나 전 송한 데이터의 양을 보여줍니다. 서비스 제공자가 사용자로 하여금 GSM 명령 (코드 또는 프로시저라고도 불림)을 입력하도 록 하면, 메인창에서 명령을 입력하도록 하십시오. 시스템 트레이 아이콘 Watcher가 실행된 상태에서 Watcher 아이콘은 시스템 트레이에 나타나게 되며 연결 상태를 표시합니다: Watcher가 3G 모뎀을 검색하지 못했습니다.
4 64 노트북 PC 사용
부록 액세서리 & 연결 옵션 운영 시스템 및 소프트웨어 시스템 BIOS 설정 일반적인 문제와 해결 Windows 소프트웨어 복구 용어 설명 성명서 및 안전 정보 노트북 PC 정보 본 설명서 내의 그림과 제품 자체의 실제 모습은 차이가 있을 수 있습니다. 노트북 PC의 내 용이 설명서의 그림에 우선합니다. 참고: 본 설명서에 사용된 사진과 아이콘은 사용자의 이해를 돕기 위한 이미지이며, 제품 자체에서의 실제 모습과 다를 수 있습니다.
A 부록 액세서리 옵션 이 장치들을 노트북 PC에 추가로 장착할 수 있습니다. USB 허브 (옵션) USB 허브를 장착하면 더 많은 USB 포트를 사용할 수 있으며, 하나의 케이블을 통해 빠르고 간편하게 USB 주변장치를 연결 또는 해제할 수 있습니다. USB 플래시 메모리 디스크 USB 플래시 메모리는 최대 수백 메가바이트의 저장용량과 빠른 전송 속도, 안정된 내구성을 갖춘 장치로 1.44MB 플로피 디스크의 대체 장 치입니다. USB 포트를 사용하는 모든 컴퓨터와 호환이 되며 드라이버 를 설치할 필요없이 사용 가능합니다. USB 플로피 디스크 드라이브 표준형 1.44MB (또는 720KB) 3.5 플로피 디스켓을 인식할 수 있는 USB 인터페이스의 디스크 드라이브를 추가로 장착할 수 있습니다. 경고! 시스템의 손상을 방지하기 위해 USB 플로피 디스크 드라이브 를 제거하기 전에, 작업 표시줄에 위치한 하드웨어 안전하게 제거하 기을 클릭하여 주십시오.
부록 A 연결 옵션 이 장치들은 사용자의 노트북 PC에 추가로 장착할 수 있습니다. USB 키보드와 마우스 외장 USB 키보드 사용 시 보다 쉽게 데이터를 입력할 수 있 으며, 외장 마우스를 사용하면 Windows 검색 시 용이합니 다. 외장 USB 키보드와 마우스는 노트북 PC 키보드, 터치 패드와 동시에 사용 가능합니다. 프린터 연결 USB 포트나 USB 허브에 연결하여 동시에 여러 대의 프린터를 사용할 수 있습니다.
A 부록 Bluetooth 마우스 설정 (옵션) 이 절차는 Windows 운영 체제에서 대부분의 Bluetooth 장치를 추가하는데 사용됩니다. 1. 필요 시, 무선 스위치의 전원을 켜 주십시오 (제 3장의 스위치 참고) . 3. 작업 표시줄 메뉴에서 Bluetooth 장치 추가를 선 택해 주십시오. 3b. 또는 Windows 제어판에서 Bluetooth 장치를 실 행해 주십시오. ESET 2b. 또는 작업 표시줄의 무선 콘솔 아이콘을 더블 클 릭한 후, 무선 LAN + Bluetooth를 선택하거나 그 냥 Bluetooth만 선택해 주십시오. R OFF ON 2. Bluetooth ON 또는 WLAN & Bluetooth ON 표시가 나타날 때까지 [FN F2] 버튼을 눌러 주십시오. 4. Bluetooth 마우스를 준비해 주십시오. • 두 개의 “AA” 배터리를 넣어 주십시오. • 마우스 하단에 위치한 전원 스위치를 켜 주십시 오. 하단부 센서가 붉은 색으로 변합니다.
부록 A Bluetooth 마우스 설정 (옵션) (계속) 5. Bluetooth 마우스가 준비되면 다음 버튼을 클릭 해 주십시오. 6. Bluetooth 장치 목록이 나타납니다. Bluetooth 마 우스를 선택하고 다음 버튼을 클릭해 주십시오. 7. “패스 키 사용하지 않음”을 선택한 후, 다음 버튼 을 클릭해 주십시오. 8. Bluetooth 마우스가 추가될 때까지 기다려 주십 시오. 9. 추가 작업이 완료되면 마침 버튼을 클릭해 주십 시오. 10. Windows에서 장치를 볼 수 있습니다. 이 곳에 서 Bluetooth 장치를 추가 또는 제거할 수 있습 니다. 참고: 배터리를 교체한 후에 재설정이 필요할 수 있습니다. 위의 절차를 다시 한번 시도해 주십시오.
A 부록 운영 시스템 및 소프트웨어 본 노트북 PC는 지역에 따라 고객에게 Microsoft Windows 운영 시스템을 미리 설치해 주는 옵션을 제공합니다. 선택 범위와 언어는 지역에 따라 다를 수 있으며, 설치된 운영 시스템에 따라 하드웨어 및 소프트웨어 사양이 다를 수 있습니다. 기타 다른 운영 시스템 사용 시, 노트 북 PC와의 호환성과 시스템 안정성에 관해서는 제조사가 책임을 지지 않습니다. 소프트웨어 지원 본 노트북 PC는 운영체제가 제공하지 않는 하드웨어 기능 활성화 및 기능 확장 그리고 노트북 PC 관리 또는 기능 추가를 위한 BIOS, 드라이버 및 어 플리케이션을 포함한 지원 디스크를 함께 제공합니다. 지원 CD를 분실하 였거나 업데이트가 필요할 경우, 판매처에 문의하여 웹 사이트에서 각각의 필요한 소프트웨어 및 유틸리티를 다운로드 하십시오. 지원 디스크에는 이미 설치된 운영체제 및 기타 운영체제의 모든 드라이버 와 유틸리티 그리고 소프트웨어가 포함되어 있습니다.
부록 A 시스템 BIOS 설정 부팅 장치 1. Boot 스크린에서 Boot Device Priority를 선택해 주십시오. 2. 각 항목을 선택한 후, [Enter] 버튼을 눌러 장치를 선택해 주십시오. 보안 설정 비밀번호 취소 방법: 2. 비밀번호를 입력한 뒤, [Enter]를 눌러 주십시오. 1.비밀번호 항목을 빈 칸 으로 두고 [Enter]를 눌러 주십시오. 3. 비밀번호를 다시 입력 하고 [Enter]를 눌러 주 십시오. 2. 비밀번호가 취소되었습 니다. 1. Security 스크린에서 Change Supervisor 또는 Change User Password를 선택해 주십시오. 4. 비밀번호가 설정되었 습니다.
A 부록 시스템 BIOS 설정 (계속) 비밀번호 확인 부팅 시(항상) 비밀번호를 요구할 것인지 또는 BIOS 셋업 유 틸리티(셋업) 실행 시만 요구할 것인지 선택해 주십시오. 사용자 접속 수준 접속 수준을 선택하여 “사용자 비밀번호”를 BIOS 셋업 유틸 리티에 적용시켜 주십시오. 변경 사항 저장 사용자의 구성 설정을 저장하려면, BIOS 셋업 유틸리티 를 종료하기 전에 설정을 저장해야 합니다. 기본 설정을 다시 복구하려면, Load Manufacture Defaults을 선택해 주십시오. 공창 초기화 기본 설정을 유지하려면, 설정을 저장해야 합니다.
부록 A 일반적인 문제 및 해결 하드웨어 문제 - 옵티컬 디스크 옵티컬 디스크 드라이브가 디스크를 읽거나 쓸 수 없습니다 1. BIOS를 최신 버전으로 업데이트한 후, 다시 시도해 주십시오. 2. BIOS를 업데이트 해도 문제가 해결되지 않는다면, 다른 디스크를 사용해 보십시오. 3. 그래도 문제가 해결되지 않는다면, 가까운 서비스 센터 또는 기술자에게 문의해 주시 기 바랍니다. 알 수 없는 이유 - 시스템 불안정 최대절전모드에서 컴퓨터를 깨울 수 없습니다. 1. 노트북 PC 구입 이후 설치된 업그레이드된 부분(RAM, HDD, WLAN, BT)을 제거해 주십시오. 2. 문제가 해결되지 않는다면, 이전 날짜로 MS System Restore을 시도해 주십시오. 3. 문제가 지속된다면, 복구 파티션 또는 DVD를 사용하여 시스템을 복구해 주십시오. (참고: 복구하기 전에, 모든 데이터를 다른 곳에 옮겨 주십시오.) 4.
A 부록 일반적인 문제 및 해결 (계속) 하드웨어 문제 - 전원 ON/OFF 오류 노트북 PC 전원을 켤 수 없습니다.. 진단: 1. 배터리 전원을 이용해 컴퓨터를 켤 수 있습니까? (예 = 2, 아니요 = 4) 2. BIOS 설정 화면이 보입니까 (ASUS 로고)? (예 = 3, 아니요 = A) 3. OS를 로딩할 수 있습니까? (예 = B, 아니요 = A) 4. 어댑터 전원 LED에 불이 들어옵니까? (예 = 5, 아니요 = C) 5. 어댑터 전원을 사용하여 전원을 켤 수 있습니까? (예 = 6, 아니요 = A) 6. BIOS 설정 화면이 보입니까 (ASUS 로고)? (예 = 7, 아니요 = A) 7. OS를 로딩할 수 있습니까? (예 = D, 아니요 = A) 증상 및 해결 방안: A. MB, HDD 또는 NB 관련 문제; 가까운 서비스 센터에 문의해 주십시오. B. 운영 체제에 의해 발생한 문제는 복구 파티션 또는 DVD를 사용하여 시스템을 복구해 보십시오.
부록 A 일반적인 문제 및 해결 (계속) 소프트웨어 문제 - ASUS 제공 소프트웨어 노트북 PC를 켜면, Open policy file error” 메시지가 나타납니다. A. 최신 버전의“Power4 Gear” 유틸리티를 설치하여 문제를 해결할 수 있습니다. ASUS 웹사이트에서 최신 버전을 다운로드 받을 수 있습니다. 알 수 없는 이유 - 파란 화면에 하얀 글자 시스템 부팅 후, 파란 화면에 하얀 글자가 나타납니다. 1. 추가 장착 메모리를 제거해 주십시오. 만약 추가의 메모리를 노트북 PC 구입 이후 장 착한 것이라면, 전원을 끄고 추가 메모리를 제거한 후, 전원을 다시 켜 주십시오. 메 모리 호환의 문제일 수도 있습니다. 2. 소프트웨어 어플리케이션을 제거해 주십시오. 최근 설치한 소프트웨어 어플리케이션 이 시스템과 호환이 안되는 경우가 있을 수 있습니다. Windows Safe Mode에서 설치 한 어플리케이션을 제거해 주십시오. 3. 바이러스가 있는지 시스템을 확인해 주십시오. 4.
A 부록 소프트웨어 문제 - BIOS BIOS 업데이트. 1. 노트북 PC의 정확한 모델명을 확인한 후, ASUS 웹 사이트에서 최신 BIOS 파일을 다 운로드 해 주십시오. 2. “WINFLASH” 유틸리티를 사용하여 BIOS를 업데이트 해 주십시오. 유틸리티는 구입 시 함께 제공된 드라이버 & 유틸리티 CD에서 찾을 수 있습니다. 3. BIOS 파일을 임시 공간에 위치시켜 주십시오. (예: C:\) 4. 시작 | 모든 프로그램 | ASUS 유틸리티 | WINFLASH | WINFLASH를 클릭해 주십시오. a. 새로운 BIOS 이미지 파일을 선택해 주십시오. b. 선택한 BIOS 정보를 확인해 주십시오. 모델과 버전, 날짜를 확인해 주십시오. c. Flash 버튼을 클릭하여 BIOS 업데이트 절차를 실행해 주십시오. d. 업데이트 절차를 완료하면 Exit 버튼을 클릭해 주십시오. e. 시스템을 다시 시작해 주십시오.
부록 A 일반적인 문제 및 해결 (계속) Symantec의 Norton Internet Security (NIS) 1. NIS는 로컬 IP 주소로부터 트로이안 바이러스를 중지하도록 경고할 수도 있습니다. 이 문제는 바이러스 정의 파일이 최신 버젼이거나 또는 최신파일로 업데이트 함으로 해결 할 수 있습니다. 2. 노턴 안티바이러스를 삭제한 후 “Information Wisard”에서의 재설치 실패 컴퓨터에서 NIS가 삭제되었는지 확인한 후, 재부팅하시고, NIS를 재설치하십시오. 그 후 “Live Update”를 이용하여 바이러스 정의 파일을 업데이트하십시오. 3. 노턴 프로그램은 특정 웹사이트를 차단하거나 다운로드 속도를 감소시킬 수 있습니다. 보안 설정을 한 단계 낮추십시오. 데이터를 다운로드하는 동안 NIS가 바이러스를 스캔하기 때문에 네트워크 속도가 느려질 수 있습니다. 4.
A 부록 일반적인 문제 및 해결 (계속) 9. “Notron Internet Security” 또는 “Norton Person Firewall”를 설치하시기 전에 Windows 방화벽 서비스는 반드시 정지하셔야 합니다. 윈도우즈 방화벽서비스 정지하기: 1. 시작 버튼을 누르시고 제어판을 클릭하십시오. 2. 두 제어판 중에 하나가 나타나면 보안센터 아이콘을 클릭하십시오. 3. 상태 업데이트의 아래에 있는 Windows 방화벽 아이콘을 클릭하십시오. 4. 사용 안함을 선택하고 확인을 클릭하십시오. 10. 왜 “Privacy Control”아이콘에 ‘x’가 나타납니까? “상태 & 설정”에서 Privacy Control 를 끄십시오. 11. 권한 제한 메시지가 나타납니다. NIS 삭제, 사용안함을 포함하여 많은 설정 변경에서 관리자 모드로 윈도우즈에 로그온 해 야 합니다. 로그오프하시고 윈도우즈 관리자 모드로 사용자전환하십시오.
부록 A Windows Vista 소프트웨어 복구 하드디스크 파티션 사용하기 Recovery Partition 공장 출하시 노트북에 설치된 운영 시스템, 드라이버, 그리고 유틸리티 이 미지를 포함하고 있습니다. Recovery Partition는 노트북 PC의 소프트웨어를 원래의 초기 의 최적의 상태로 빠르고 쉽게 돌아갈 수 있는 복구 솔루션을 제공해 줍니다. Recovery Partition를 사용하기 전, 데이터 파일(Outlook PST 파일 등)을 플로피 디스크 또는 네트워크 드라이브에 저장해 두고 사용자의 구성 설정(네트워크 설정 등)을 기록해 두십시오. Recovery Partition에 관해: Recovery Partition는 공장 출하시에 설치된 노트북 PC의 운영 시스템, 드라이버, 유틸리티를 복구하기 위해 하드디스크에 저장된 공간입니다. 중요: 중요: ����������������������������� “RECOVERY”라고 되어 있는 파티션을 삭 제하지 마십시오.
A 부록 Windows Vista 소프트웨어 복구 (계속) Recovery DVD 사용 (일부 모델) Recovery DVD에는 노트북 PC에 설치된 운영 시스템, 드라이버, 그리고 유틸리티 이미지가 포함되어 있습니다. Recovery DVD는 노트북 PC의 소프트웨어를 빠르게 공장 초기화 상태로 복구시킬 수 있는 복구 솔루션을 제공합니다. Recovery DVD를 사용하기 전에, 데이터 파일 (Outlook PST 파일 등)을 플로피 디스크 또는 네트워크 드라이브에 복사하고, 구성 설정(네트 워크 설정 등)을 기록해 주십시오. 중요! 노트북 PC에서 시스템 복구를 실행하기 전에 추가 보조 하드디스크 드라이브를 제거 해 주십시오. Microsoft에 따르면, Windows Vista를 올바르지 않은 디스크 드라이브에 설 치하거나, 올바르지 않은 드라이브 파티션을 포맷할 경우 중요한 데이터를 잃게 됩니다. 자 세한 사항은 http://support.microsoft.
부록 A 용어 설명 ACPI (Advanced Configuration and Power Management Interface) 컴퓨터의 전력 사용량을 줄이기 위한 표준 규격 APM (Advanced Power Management) 컴퓨터의 전력 사용량을 줄이기 위한 표준 규격 AWG (American Wire Gauge) 참고: 아래의 표는 단지 참고용입니다. 최신 업데이트된 자료가 아니기 때문에, AWG 규격 의 자료로 사용할 수 없습니다. Gauge AWG 33 32 30 29 27 26 25 Diam (mm) 0.18 0.19 0.20 0.25 0.30 0.35 0.40 0.45 Area (mm2) 0.026 0.028 0.031 0.049 0.071 0.096 0.13 0.
A 부록 용어 설명 (계속) 중앙 처리 장치 (CPU) CPU 또는 “프로세서” 라고도 불리우며, 실제로 컴퓨터의 “두뇌” 역할을 하는 중추기능으로, 모든 프로그램의 실행 명령을 내리고 메모리에 저장된 데이터를 처리하고 해석하는 역할을 합니다. 장치 드라이버 장치 드라이버는 컴퓨터의 운영 체제와 VGA, 오디오, 이더넷, 프린터, 모뎀 등과 같은 장치들 사이의 통신 교두보 역할을 하는 명령어입니다. DVD DVD는 많은 용량의 비디오와 오디오 그리고 컴퓨터 데이터를 빠른 속도로 저장할 수 있는 치입니다. DVD 디스크는 다채로운 색깔과 깨끗한 동영상, 향상된 그래픽, 또렷한 이미지, 리고 돌비 디지털 서라운드를 지원하여 영화관에 있는 듯한 효과를 제공합니다. DVD는 홈 터테인먼트와 컴퓨터, 사업상의 중요한 정보를 단일 디지털 형식으로 저장하여, 이후에는 존의 사용되어 오던 오디오 CD, 비디오 테이프, 레이저 디스크, CD-ROM, 심지어 비디오 임 카트리지 대신에 DVD가 사용될 전망입니다.
부록 A 용어 설명 (계속) 레이저 분류 레이저는 수많은 곳에서 여러가지 방법으로 널리 사용되고 있으며, 그 만큼 인체에 노출되는 가능성도 높아져 항상 사용자의 주의가 요구됩니다. 이러한 주의의 필요성에 의해 레이저의 가 시 강도의 위험에 따라 분류되었고 위험의 강도가 덜한 1 등급 부터 엄격한 안전 주의가 필요 한 4 등급까지 분류되어 있습니다. 등급 1: 1 등급 레이저 또는 레이저 방출 시스템은 눈에 안전한 레벨로써 주의가 필요한 등급 은 아닙니다. 이 등급의 레이저 시스템은 대부분의 마트에서 사용되는 바코드 검사기나 광 학 드라이브에서 사용되는 레이저 등급입니다. 등급 2와 등급 3A: 2 등급과 3A 등급에 해당하는 레이저는 눈에 선명하게 보이며 지속적인 파 장(CW)이 나타나는 단계로 노출에는 지장이 없는 MPE(maximum permissible exposure )레벨 보다 조금 더 높은 단계의 레이저 등급입니다.
A 부록 용어 설명 (계속) 대기모드 “대기모드(STR)”와 “최대 절전 모드(STD)”로 전환이 되면, CPU 클럭은 멈추고 노트북 PC 대 부분의 장치들은 낮은 활성 상태로 전환됩니다. 대기모드는 노트북 PC의 가장 낮은 전력 사 용모드로 일정시간 노트북 PC를 사용하지 않거나 [Fn]+[F1]키의 조합으로 전환됩니다. 노 트북 PC가 대기 모드로 전환되면 전원 LED는 깜박거리게 되고 최대 절전 모드로 전환될 시, 노트북 PC는 전원이 꺼진것 처럼 보이게 됩니다. 시스템 디스크 시스템 디스크는 운영체제의 핵심 파일이 저장되어 있어 운영 시스템을 부팅할 목적으로 사 용됩니다. TPM (Trusted Platform Module) (일부 모델) TPM은 컴퓨터 키로 암호화된 보안 모듈로, 시스템 보드에 장착되어 있습니다. TPM은 해커들 이 비밀번호를 알아내기 위해 침입해 중요한 데이터의 암호화 키를 알아내려고 할 경우, 이러 한 공격들을 차단하는 하드웨어 기반의 솔루션입니다.
부록 A 성명서 및 안전 정보 DVD-ROM 드라이브 정보 DVD-ROM이나 CD-ROM 드라이브를 추가 연결하여 노트북 PC에서 영화를 감상할 수 있습 니다. DVD 타이틀을 보려면, DVD 플레이어 프로그램을 설치해야만 합니다. 본 노트북 PC 구 매 시, 기본 제공된 DVD 플레이어 소프트웨어를 설치해 주십시오. DVD-ROM 드라이브에서 는 CD와 DVD디스크 모두 사용할 수 있습니다. 재생 지역 코드 (Regional Playback Information) DVD 영화 타이틀에는 돌비 AC3, MPEG2 녹화기술과 불법복제를 막기위한 CSS 방식이 적용 되어 있습니다. CSS 방식은 불법 복제를 막기 위한 영화 산업 운동에 의해 채택된 저작권 보 호 계획의 하나입니다. CSS 등록자들에 의해 제정된 규칙 중 가장 보편적으로 사용되는 방법은 DVD 재생 시, 각 지 역별로 DVD 재생에 관한 제한을 두는 방식입니다.
A 부록 내장 모뎀 규격 노트북 PC의 내장 모뎀은 JATE (일본), FCC (미국, 캐나다, 한국, 대만), and CTR21의 기준 을 따릅니다. 내장 모뎀은 범 유럽 단일 단말기를 공중 전화교환망(PSTN)에 연결하기 위한 98/482/EC 결정의 승인을 받았습니다. 그러나, 각 나라에 제공되는 PSTN이 달라, 의회 승인 그 자체로는 효력이 발생하지 않으므로, 모든 PSTN에 연결하는 작업이 원할하지 않습니다.만 약 문제가 발생한다면, 사용자의 장치 제조업체에 문의 해주십시오. 개요 1998년 8월 4일 CTR21에 언급된 EC의 결정문의 내용은 EC 정부 간행물 부서에서 출판되 었으며 CTR 21 규정은 아날로그 PSTN (Public Switched Telephone Network)에 연결되는 DTMF-신호 규격을 따르는 비음성 단말 장치에 적용됩니다.
부록 A 내장 모뎀 규격 (계속) 다음의 표는 CTR21 표준이 적용되는 국가입니다.
A 부록 미연방 통신 위원회 성명서 본 장치는 FCC 규정 제 15조를 준수하며 아래의 조건을 만족합니다: • 본 장치는 해로운 장해를 일으키지 않습니다. • 본 장치는 불필요한 작동을 유발하는 장해를 포함하여 모든 장해를 수용합니다. 본 기기는 FCC 규정 제 15조에 의거하여 테스트 되었으며, B등급 디지털 장치에 대한 제한 사항을 준수합니다. 이러한 제한 사항은 주거 지역에서 장치 설치 시에 유해한 간섭을 방지하 기 위한 것입니다. 본 장치는 RF(Radio Frequency) 에너지를 생성, 사용하고 방출하므로, 지 시 사항에 따라 장치를 설치하지 않을 경우 전파 간섭이 발생할 수 있습니다. 장치의 전원을 껐다 켜봄으로써, 라디오 또는 텔레비전 수신에 대한 유해한 간섭이 발생하는지의 여부를 확 인할 수 있습니다. 간섭이 발생하는 경우, 다음과 같은 방법으로 전자파 장애를 교정하는 것 이 좋습니다.�: • • • • 수신 안테나의 방향을 바꾸거나 위치를 바꾸어 주십시오.
부록 A FCC 무선 주파수 (RF) 노출 지침 본 장치는 예기치 않은 환경을 위한 FCC 무선 주파수 노출 제한을 만족합니다. FCC RF 노출 만족 요구 사항을 준수하기 위해, 사용자는 작동 지시 사항을 반드시 따라 주시기 바랍니다. 본 장치는 5.15~5.25GHz의 주파수로 작동며, 실내 사용으로 제한을 두십시오. FCC 주의 사항: 승인되지 않은 어떠한 변경이나 개조는 이 장치를 사용하는 사용자의 권 리를 무효로 할 수 있습니다.“제조업체는 미국에서 조절되는 특정 펌웨어에 의해 2.4GHz 주파수에서 채널 1부터 11까지 제한되어 있음을 확인했습니다.” FCC RF 노출 지침 사항 (무선 클라이언트) 이 장치는 전형적인 이동 구성에서의 FCC RF 노출 (SAR) 제한을 만족합니다. ANSI95.
A 부록 도메인 별 무선 작동 채널 북미 일본 유럽 ETSI 2.412-2.462 GHz 2.412-2.484 GHz 2.412-2.472 GHz Ch 01~CH11 Ch 01~Ch14 Ch 01~Ch13 프랑스 제한 주파수 대역 프랑스의 일부 지역은 특정 주파수 대역의 사용이 제한됩니다. 가장 엄격한 곳은 실내에서 다 음과 같이 제한됩니다: • 전체 2.4 GHz에서 10mW (2400 MHz–2483.5 MHz) • 2446.5MHz와 2483.5MHz 사이에서 100mW 참고: 채널10~13은 2446.6MHz~2483.5MHz에서 작동합니다. 실외의 경우에는 예외가 있습니다. 사유 재산 또는 공인의 사유 재산에서는 국방부 장관에 의 해 예비 승인 절차를 얻어 사용이 가능합니다. 최대 승인 전력은 2446.5-2483.5 MHz에서 100mW입니다. 실외의 공공재산에서는 사용이 허가되지 않았습니다.� 전체 2.
부록 A UL 안전 통보 최대 200V peak, 300V peak to peak, 105V rms를 초과하지 않는 최저 작동 전압으로 원거 리 통신망에 접속하거나 국가 전격 코드(NFPA 70)에 의거하여 사용, 설치되는 원격 통신(전 화)에는 UL1459 규정이 요구됩니다. 노트북 PC 모뎀을 사용할 때, 발화, 전기쇼크, 신체적 상해의 위험을 줄이기 위해 항상 다음 과 같은 기본 안전 수칙을 준수해야 합니다�: • ������������ 욕조, 세탁기, 부엌 싱크대, ������������������������������������� 세탁조, 습기가 많은 지하실, 수영장 등 물 가까이에서 노 트북 PC를 사용하지 마십시오. • ���������������������������� 번개를 동반한 폭풍 시에는 노트북 PC를 사용하지 마십시오. 번개에 의한 전기쇼크 의 위험이 발생할 수 있습니다. • ������������������������ 가스가 새는 곳에서 노트북 PC를 사용하지 마십시오.
A 부록 EU(유럽 연합) 에코 라벨 (Eco-label) 본 노트북 PC는 노트북이 다음의 성격을 가짐을 의미하는 EU 플라워 등급의 라벨을 수상했 습니다: 1. 사용 시 또는 대기 모드에서 에너지의 소비 감소 2. 유해한 중금속의 사용 제한 3. 환경과 건강에 해로운 물질의 사용 제한 4. 재활용을 장려함으로써 자연 자원 사용의 감소* 5. 간편한 업그레이드와 보다 추가 부품의 길어진 유효 기간을 통해 제품 수명의 연장. 6. 반환 정책을 통한 고체 및 고형 쓰레기의 감소* EU 플라워 라벨에 관한 추가 정보는 EU Eco-label 홈페이지: http://europa.eu.int/ecolabel에서 확인이 가능합니다. *ASUS의 재활용 및 반환 프로그램은 자연을 보호하기 위한 높은 표준에 대한 우리의 굳 은 의지에서 표출됩니다. 본사는 고객이 책임을 가지고, 본사의 제품을 재활용할 수 있 도록 솔루션을 제공하고 있다고 믿습니다.
부록 A 반환 및 재활용 재활용의 이유? 오래된 컴퓨터, 노트북 컴퓨터 및 기타 전자 장치는 일반 쓰레기와 함께 매립지에 폐기될 시 해가 되는 해로운 화학 물질을 포함하고 있습니다. 오래된 컴퓨터에서 발견할 수 있는 금속, 플라스틱 및 구성 요소를 분해하여 재활용하여 새 제품을 만드는데 사용될 수 있습니다. 또한 해로운 화학 물질의 노출을 통제하여 환경 보호에 일조할 수도 있습니다. ASUS는 환경을 보호 하고 근로자의 안전을 보장하며 글로벌 환경 법규에 부합하기 위한 최 고 수준의 표준을 만족하는 재활용 업체들과 함께 합니다. 오래된 장치의 재활용은 환경 보호 를 위한 본사의 여러 노력 중의 하나이며, 이는 본사의 의무입니다. ASUS 제품 재활용 및 연락처에 대한 추가 정보는 GreenASUS Takeback and Recycling 페 이지 (http://green.asus.com/english/takeback.htm)에서 확인할 수 있습니다.
A 부록 북방 국가 경고 사항 (리튬 이온 배터리) CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. (영어) ATTENZIONE! Rischio di esplosione della batteria se sostituita in modo errato. Sostituire la batteria con un una di tipo uguale o equivalente consigliata dalla fabbrica. Non disperdere le batterie nell’ambiente.
부록 A 옵티컬 드라이브 안전 정보 레이져 안전 정보 외장 또는 내장 광학 드라이브는 1등급 수준의 레이저 제품(LASER KLASSE 1 PRODUCT)을 포함한 노트북 PC와 함께 판매 되며 레이저에 대한 상세 등급은 사용자 설명서 후반부에 상 세하게 기술되어 있으므로 참고하시기 바랍니다. 경고: 본 사용 설명서에 기술되지 않은 작업을 하거나 변형시키면 위험한 레이저에 노출 될 수 있습니다. 옵티컬 드라이브를 분해하지 마십시오. 여러분의 안전을 위해, 인증된 서비스 센터에 옵티컬 드라이브에 관한 문의를 해주십시오. 서비스 경고 라벨 주의: 드라이브가 열리면 비가시 레이저 복사 에너지가 방출됩니다. 눈에 광선이 직접 쏘 이지 않도록 주의 해 주십시오. CDRH 규정 미국 식품 의약청 산하 의료기기 및 방사선 보건 센터(CDRH)는 1976년 8월 2일 레이저 제품 에 대한 규정을 시행하였습니다.
A 부록 CTR 21 승인 (내장형 모뎀 장착 노트북 PC) 덴마크어 네덜란드어 영어 핀란드어 프랑스어 독일어 그리스어 이탈리아어 포르투칼어 스페인어 스웨덴어 A-32
부록 A A-33
A 부록 노트북 PC 정보 이 페이지에 기록된 사용자의 노트북 PC에 관한 정보는 추후, 기술 지원 등, 참고가 될 수 있 도록 하는데 그 목적이 있습니다. 더불어 A/S를 받고자 할 경우 빠른 서비스를 위한 참고자료 가 될 수 있습니다. 만약 비밀번호를 적어 두셨다면 안전한 장소에 보관해 주십시오.