F6951 Manuel d'utilisation pour PC portable Février 2012
Table des matières Chapitre 1 : Présentation du PC portable A propos de ce manuel d'utilisation............................................................ 6 Remarques concernant ce manuel............................................................... 6 Précautions d’emploi......................................................................................... 7 Préparer votre PC portable............................................................................
Utiliser la touche Instant Key........................................................................47 Utiliser la touche Instant Key pour la première fois............................47 Chapitre 4 : Utiliser le PC portable Pointeur................................................................................................................52 Utiliser le pavé tactile.....................................................................................53 Illustrations sur l’utilisation du pavé tactile...
Déclarations et avertissements de Sécurité....................................... A-26 Rapport de la Commission Fédérale des Communications........ A-26 Directives FCC concernant l’exposition aux fréquences radio... A-27 Déclaration de conformité (directive R&TTE 1999/5/EC)............. A-27 Déclaration d’Industrie Canada relative à l’exposition aux ondes radio........................................................................................... A-28 Canaux d’opérations sans fil régionaux..............
1 Chapitre 1 : Présentation du PC portable
A propos de ce manuel d'utilisation Vous lisez le manuel d'utilisation de votre PC portable. Celui-ci fournit des informations sur la façon d'utiliser le PC portable. Les principales parties de ce manuel d'utilisation sont les suivantes : 1. Présentation du PC portable Présente le PC portable et le manuel de l’utilisateur. 2. Présentation des éléments du PC portable Fournit des informations sur les composants du PC portable. 3.
Précautions d’emploi Les consignes de sécurité qui suivent augmenteront la durée de vie du PC portable. Suivez-les à la lettre. Pour ce qui n’est pas décrit dans ce manuel, demandez l’assistance d’une personne qualifiée. Débranchez l’alimentation et retirez la(les) batterie(s) avant le nettoyage. Essuyez le portable avec une éponge de cellulose propre ou une peau de chamois imbibée d’une solution non abrasive et d’un peu d’eau tiède, puis retirez l’humidité restante avec un chiffon sec.
Température de fonctionnement : pendant l’utilisation, le portable doit être exposé à une température ambiante comprise entre 5°C (41°F) et 35°C (95°F) PUISSANCE : Référezvous à l’étiquette cicontre, située au dessous du portable, afin de vérifier que votre adaptateur secteur répond aux exigences de voltage. NE PAS transporter ou recouvrir le portable SOUS TENSION avec un matériau qui ne permet pas, comme une sacoche de transport, une circulation d’air optimale.
Pression acoustique Avertissement : Une pression acoustique excessive provenant d’écouteurs ou d’un casque d’écoute peut entraîner la perte de l’audition. Veuillez noter que l’ajustement du volume et l’égaliseur au dessus de leur position centrale peut accroître le voltage de sortie des écouteurs ou du casque d’écoute et par conséquent le niveau de pression acoustique. Ventilateur DC Avertissement : le ventilateur DC est un composant mobile pouvant être dangereux.
Couvrir votre ordinateur portable Faites l'achat d'une sacoche de transport pour protéger l'ordinateur portable de la saleté, de l’eau, des chocs et des éraflures. Charger les batteries Si vous comptez utiliser l'alimentation sur batterie, assurez-vous d’avoir rechargé complètement le bloc batterie, ainsi que tout bloc batterie optionnel, avant d'entreprendre de longs voyages. Remarque : l'adaptateur électrique charge le bloc batterie lorsqu’il est branché sur l'ordinateur et sur une source d'alimentation.
Préparer votre PC portable Voici quelques instructions rapides pour utiliser votre portable.
Ouvrir l’écran 1. Soulevez délicatement le panneau d’affichage avec votre pouce. 2. Relevez doucement l’écran avec votre pouce pour optimiser l’angle de vision. Allumer l’ordinateur portable 1. Appuyez sur le bouton de mise en route localisé sous le panneau d’affichage LCD. 2. Utilisez les touches [Fn]+[F5] ou [Fn]+[F6] pour ajuster la luminosité de l’écran LCD.
2 Chapitre 2 : Présentation des éléments du PC portable
Dessus Le clavier varie en fonction du pays.
1 ������������������ Microphone intégré ������������������������������������������������� Le microphone intégré peut être utilisé pour les visioconférénces, la narration audio ou de simples enregistrements audio. 2 Caméra ������������������������������������������������ La caméra intégrée permet de prendre des photos ou d’enregistrer des vidéos. Elle peut être utilisée en visioconférence ou pour d’autres applications interactives.
7 8 9 16 Clavier Le clavier offre des touches de grandes tailles avec une amplitude confortable (profondeur à laquelle les touches peuvent être enfoncées) et un repose-poignet pour les deux mains. Deux touches de fonction Windows permettent une navigation facile sous Windows. Pavé tactile et ses boutons Le pavé tactile et ses boutons constituent un système de pointage qui offre les mêmes fonctions qu’une souris.
Dessous L’apparence du dessous varie en fonction des modèles. La taille de la batterie varie en fonction des modèles. AVERTISSEMENT ! Le dessous du PC portable peut devenir très chaud. Faites attention en manipulant le PC portable lorsque ce dernier est allumé ou lorsqu’il a été utilisé récemment. Une température élevée est normale lors de la charge ou de l’utilisation du PC portable.
1 18 Batterie La batterie se charge automatiquement une fois reliée à une source d’alimentation électrique et alimente le portable quand il n’est pas connecté à une source de courant électrique. Ceci permet l’utilisation du portable lors de déplacements temporaires. La durée d’utilisation de la batterie varie selon le type d’usage et les spécifications propres à ce portable. La batterie ne doit pas être démontée, et doit être achetée en tant qu’élément d’un seul tenant.
Côté droit 1 2 4 5 6 7 8 Sortie pour casque audio Le jack casque stéréo (1/8 pouces) est utilisé pour connecter la sortie audio du portable à des enceintes amplifiées ou un casque. Lorsque vous utilisez ce jack, les haut-parleurs intégrés sont automatiquement désactivés. Combo 1 3 2 3 Sortie numérique (sortie SPDIF) Ce jack permet une connexion SPDIF (Interface numérique Sony/Philips) vers des appareils qui sont compatibles avec une sortie audio numérique.
4 Lecteur optique Les PC portables ASUS existent en plusieurs modèles, livrés avec des lecteurs optiques différents. Le lecteur optique des PC portables ASUS peut lire des CD et/ou DVD avec des possibilités d’écriture (R) et de réécriture (RW). Référez-vous à la documentation relative aux caractéristiques de votre modèle de PC portable. 5 Éjection électronique du lecteur optique L’éjection d’un média optique se fait via un bouton d’éjection électronique ouvrant le plateau.
8 Port de sécurité Kensington® ������������������������������������������������������� Le port pour verrou Kensington® permet de sécuriser le portable grâce aux produits, Kensington® destinés à la sécurité des PC portables, qui sont compatibles avec ASUS. Ces produits consistent en général en un câble et un verrou métallique qui permettent d’attacher le portable à un objet fixe. Certains de ces produits peuvent inclure une alarme qui se déclenche lorsque le verrou est déplacé.
Côté gauche 1 1 2 3 4 5 6 7 ����������������������������� Prise pour caisson de basses (sur une sélection de modèles) �������������������������������������������������������� Cette prise propriétaire est utilisée pour connecter le caisson de basse de l’ordinateur portable. Le caisson de basses vous permet de profiter de sons de basse vibrants (faible fréquence) dans vos applications multimédia.�. Ne connectez pas d’autres périphériques sur cette prise. Le faire peut endommager l’appareil.
4 5 6 7 Port réseau Le port huit broches LAN RJ-45 est plus large que le port pour modem RJ-11 et supporte un câble Ethernet standard pour permettre la connexion à un réseau local. Le connecteur intégré permet aisément l’utilisation d’adaptateurs supplémentaires.
Face arrière 1 1 �������� Batterie ������������������������������������������������������ La batterie se charge automatiquement une fois reliée à une source d’alimentation électrique et alimente le portable quand il n’est pas connecté à une source de courant électrique. Ceci permet l’utilisation du portable lors de déplacements temporaires. La durée d’utilisation de la batterie varie selon le type d’usage et les spécifications propres à ce portable.
Connecter le caisson de basses Le caisson de basses accompagnant votre ordinateur portable est de taille compacte et simple à transporter. Connectez simplement le caisson de basses à la prise lui étant dédié sur l'ordinateur pour profiter d'une qualité de son de basses incroyable lors de l'utilisation de vos applications multimédia. Ne forcez pas la connexion de ce caisson de basses sur d'autres prises que celle désignée sur ce manuel. Le faire peut endommager l’appareil.
3 Chapitre 3 : Mise en route
Système d’alimentation Connexion de l’alimentation L’alimentation de ce PC portable est constituée de deux parties, d’un adaptateur secteur et d’une batterie. L’adaptateur secteur convertit le courant alternatif d’une prise de courant en un courant continu pour le PC portable. Votre portable est livré avec un adaptateur secteur (alternatif-continu) universel.
IMPORTANT ! Des dommages peuvent survenir si vous utilisez un autre adaptateur ou si vous utilisez l’adaptateur du portable avec d’autres appareils électriques. Si vous constatez de la fumée, une odeur de brûlé, ou une chaleur excessive provenant de l’adaptateur secteur, contactez le SAV. Faites de même si vous pensez que votre adaptateur secteur est défectueux. Vous pourriez à la fois endommager la batterie et le PC portable avec un adaptateur secteur défectueux.
Utiliser la batterie Le PC Portable a été spécialement conçu pour fonctionner avec une batterie amovible. La batterie se compose d’un ensemble de cellules regroupées. Une batterie pleinement chargée fournira plusieurs heures d’autonomie, ce qui peut être augmenté grâce aux fonctions de gestion de l’alimentation du BIOS. Les batteries optionnelles ne sont pas fournies, et peuvent être achetées séparément auprès d’un revendeur de PC portables.
Pour retirer la batterie : 1 2 IMPORTANT ! N’utilisez que la batterie et les adaptateurs fournis avec ce PC portable, ou des modèles certifiés compatibles par le constructeur ou le revendeur, sinon le portable pourrait être 2 endommagé. 1 Entretien de la batterie Comme tous les accumulateurs, le nombre de charges de la batterie est limité. Charger et décharger complètement la batterie une fois par jour est possible pour au moins un an.
Allumer le portable Le message de mise sous tension du PC portable apparaît à l’écran lorsque vous l’allumez. Si nécessaire, vous pouvez ajuster la luminosité en utilisant les raccourcis clavier. Si vous devez lancer le BIOS pour en modifier la configuration, pressez [F2] au moment du démarrage. Si vous pressez [Tabulation] pendant l’écran d’accueil, des informations de base apparaissent, comme la version du BIOS.
Technologie S.M.A.R.T La technologie S.M.A.R.T. (Self Monitoring and Reporting Technology) vérifie l’état du disque dur durant le POST et affiche un message d’alerte si le disque dur nécessite une intervention. Si des messages d’alerte concernant le disque dur s’affichent durant l’initialisation, sauvegardez immédiatement vos données et lancez le programme de vérification des disques de Windows.
Vérifier la charge de la batterie Ce système de batterie intègre le standard Windows Smart, qui permet d’être informé sur le pourcentage de la charge batterie restante. Une batterie complètement chargée fournira plusieurs heures d’autonomie au portable . Mais cette autonomie variera en fonction de la façon dont vous utilisez les modes d’économie d’énergie, de vos habitudes de travail, du CPU, de la taille de la mémoire et de l’écran.
Charger la batterie La batterie commence à se charger dès que le portable est connecté à une source d’alimentation externe. Chargez complètement la batterie avant sa première utilisation. Une nouvelle batterie doit être complètement chargée avant de déconnecter le portable de la source d’alimentation externe. Il faut quelques heures pour charger complètement la batterie lorsque le portable est éteint, et le double de temps lorsqu’il est allumé.
Options d’alimentation L’interrupteur d’alimentation allume ou éteint le PC portable ou le met en mode veille ou veille prolongée. Le comportement de l’interrupteur d’alimentation peut être personnalisé dans la section “Options d’alimentation” du Panneau de configuration Windows.” Pour d’autres options, tel que “Changer d’utilisateur, Redémarrer, Mode veille, ou Eteindre,” cliquez sur la flèche située près de l’icône sélectionné. Redémarrer Il peut vous être demandé de redémarrer votre ordinateur.
Extinction d’urgence Au cas où votre système d’exploitation n’arriverait pas à s’éteindre ou à redémarrer correctement, il existe deux autres méthodes pour éteindre votre portable : • Appuyez sur le bouton d’alimentation 4 secondes. pendant plus de IMPORTANT ! N’utilisez pas le bouton d’arrêt d’urgence quand l’ordinateur est en train d’écrire des données sinon celles-ci seront perdues.
Modes de gestion de l’alimentation Le portable dispose d’un certain nombre de fonctions d’économie d’énergie qui sont automatiques ou configurables; vous pouvez les utiliser pour optimiser l’autonomie de la batterie et abaisser le Total Cost of Ownership (TCO). Vous pouvez piloter certaines de ces fonctions par le menu Power du BIOS. Les paramètres ACPI sont configurables via le système d’exploitation.
“Veille prolongée” est identique au mode Suspend-to-Disk (STD) et conserve vos données sur le disque dur. Ce faisant, la RAM n’a pas à être rafraîchie ce qui réduit la consommation électrique mais ne la supprime pas complètement car certains éléments de réveil, comme le réseau local et le modem ont besoin d’être alimentés. Ce mode économise plus d’énergie que le mode Veille.. Cliquez sur le bouton Démarrer, ainsi que sur la flèche située à côté de l’icône en forme de cadenas, afin de voir cette option.
Fonctions spéciales du clavier Touches colorées (sur une sélection de modèles) Ce qui suit est la description des touches colorées sur le clavier du portable. Les commandes associées aux touches colorées ne sont accessibles qu’en maintenant la touche de fonction enfoncée. L’emplacement des touches de raccourcis peut varier d’un modèle à un autre, mais les fonctions demeurent identiques. Fiezvous aux icônes plutôt qu’aux touches de fonction.
Pavé tactile barré (F9) : Appuyez sur ce bouton pour VERROUILLER (désactiver) et DEVERROUILLER (activer) votre pavé tactile lors de l’utilisation d’une souris externe. Verrouiller le pavé tactile vous empêchera de déplacer accidentellement le curseur, et permet l’utilisation d’un pointeur externe, tel qu’une souris. Note : Un indicateur, situé entre les boutons du pavé tactile, s’allume quand celui-ci est DEVERROUILLÉ (activé), et demeure éteint quand le pavé tactile est VERROUILLÉ (désactivé).
Power4Gear Hybrid (Fn+barre d'espace) : Bascule le mode d’économie d’énergie sur l’un des différents modes disponibles. Les modes d’économie d’énergie contrôlent plusieurs aspects du PC portable pour maximiser les performances par rapport à la durée de vie des batteries et, en fonction de divers évènements. Brancher ou débrancher l’adaptateur secteur fera automatiquement basculer le système du mode d’alimentation secteur au mode d’alimentation batterie. Vous pouvez visualiser le mode actuel sur l’écran.
Touches Microsoft Windows™ Il existe deux touches spéciales pour Windows™ sur le clavier : La touche avec le logo Windows™ active le menu Démarrer situé en bas à gauche du bureau Windows™. La seconde touche, qui ressemble à un menu Windows™ avec un petit curseur, active le menu des propriétés et revient à cliquer avec le bouton droit de la souris sur un objet de Windows™. Clavier étendu (selon le modèle) Un clavier étendu est disponible sur une sélection de modèles.
Touches de contrôle multimédia (sur une sélection de modèles) Les touches de contrôle multimédia vous permettent de contrôler en toute simplicité votre application multimédia. La section ci-dessous définit l’utilisation de chacune des touches de contrôle de votre PC portable. Certaines touches multimédia peuvent varier en fonction du modèle du PC portable. Utilisez la touche [Fn] combinée aux touches fléchées pour contrôler la lecture de votre CD.
Interrupteurs et Indicateurs d’état Interrupteurs ��������������������������� Interrupteur d’alimentation �������������������������������������������������������������� L’interrupteur d’alimentation allume ou éteint le PC portable ou le met en mode veille ou veille prolongée. Le comportement de l’interrupteur d’alimentation peut être personnalisé dans la section “Options d’alimentation” du Panneau de configuration de Windows.
Indicateurs d’état Indicateur d’alimentation Le voyant vert indique que le portable est allumé, il clignote lorsque le portable est en mode Veille. Ce témoin est éteint lorsque le portable est éteint ou en mode Veille prolongée. ����������������������������������������������� Témoin de charge de la batterie (deux couleurs) Le témoin de charge de la batterie utilise deux couleurs différentes pour afficher la charge de la batterie.
Indicateur d’activité du disque dur Indique que le portable accède à une ou plusieurs unités de stockage comme le disque dur. La lumière clignote proportionnellement au temps d’accès. Indicateur Bluetooth / Réseau sans fil S’applique aux modèles possédant un module Bluetooth intégré (BT) et la fonction réseau sans fil. Cet indicateur s’allume pour indiquer que la fonction Bluetooth de l'ordinateur portable est activée. Lorsque la fonction réseau sans fil est activée, l’indicateur s’allume également.
Utiliser la touche Instant Key Appuyez tout simplement sur la touche Instant Key pour exécuter rapidement la fonction lui étant attribuée. Vous ne pouvez attribuer qu'une seule fonction à la fois pour cette touche. Utiliser la touche Instant Key pour la première fois Lorsque vous appuyez pour la première fois sur la touche Instant Key, un écran de Bienvenue apparaît vous invitant à lui attribuer une fonction. Pour utiliser la touche Instant Key pour la première fois : 1.
2. À partir de l'écran de Bienvenue, cliquez sur Configuration pour ouvrir le menu des paramètres. 3. À partir de l'écran de configuration, cliquez sur l'une des icônes disponibles pour en configurer les paramètres, puis cliquez sur Appliquer. Cliquez sur les flèches situées de chaque côté de l'écran pour naviguer entre les différentes icônes.
Vous pouvez configurer les fonctionnalités suivantes : Fonction Description Contrôle du volume Augmentation/baisse du volume ou mise en sourdine. Instant App Lancement rapide des applications ou des documents fréquement utilisées. Instant Web Ouverture rapide de votre site Web favori. Mode Splendid Sélection de l'un des 6 modes d'affichage disponibles. Video Magic Exécution rapide de l'application Video Magic permettant de lire, éditer et convertir un fichier vidéo.
Fonction Description Sélecteur d'affichage Bascule rapidement d'une source d'affichage à l'autre. Cette fonction est similaire au raccourci clavier + . Connectivité sans fil Permet d'activer ou de désactiver les connexions sans fil et Bluetooth. Cette fonction est ����������������� similaire au raccourci���������� clavier � + .. Interface multimédia Exécution rapide de l'application��������������� Windows Media Player.
4 Chapitre 4 : Utiliser le PC portable
Pointeur Le pavé tactile est sensible à la pression et ne contient aucune pièce mobile ; de ce fait, les pannes mécaniques sont exclues. Un pilote est nécessaire pour qu’il fonctionne avec certaines applications. Clic droit (en dehors de la zone pointillée) Clic gauche (à l’intérieur de la zone pointillée) IMPORTANT ! N’utilisez aucun objet à la place de votre doigt pour faire fonctionner le pavé tactile, vous pourriez endommager la surface du pavé tactile.
Utiliser le pavé tactile Le pavé tactile vous permet d’utiliser vos doigts pour déplacer le curseur à l’écran et sélectionner des éléments sans avoir à utiliser de souris. il permet d’utiliser des gestes à un ou plusieurs doigts pour déplacer le curseur, cliquer et sélectionner un élément à l’écran, zoomer et faire pivoter des images, faire défiler des pages et basculer d’un document ou d’une fenêtre à l’autre.
Illustrations sur l’utilisation du pavé tactile Frappé - Touchez légèrement le pavé tactile avec le bout de votre doigt pour sélectionner un élément ou ouvrir un fichier. Appuyez une fois pour sélectionner un élément. Appuyez deux fois pour ouvrir l'élément sélectionné. Cliqué - Cliquer sur la pavé tactile simule un clic droit ou gauche de souris. Clic droit Clic gauche Cliquez une fois pour sélectionner un élément, puis double-cliquez pour l’ouvrir.
Rotation - La rotation d'images vers la droite ou la gauche est effectuée vie un pincement des doigts. Placez deux doigts au centre du pavé tactile puis tracez un arc de cercle avec l'autre doigt pour faire pivoter une photo ou un document. Défilement - Utilisez deux doigts pour faire défiler des pages Web ou de documents vers le haut ou le bas. Pour activer le défilement continu, maintenez vos doigts sur la bordure du pavé tactile puis déplacez-les vers le haut ou le bas et vice versa.
Changement de page à trois doigts - Faites glisser trois doigts de manière horizontale ou horizontale sur le pavé tactile pour passer d’une page à une autre. Vous pouvez aussi utiliser ce geste pour basculer entre vos fenêtres actives. Entretien du pavé tactile La surface du pavé tactile est sensible à la pression. Si elle n’est pas correctement entretenue, elle peut facilement s’endommager.
Désactivation automatique du pavé tactile Windows peut désactiver automatiquement le pavé tactile du portable lorsqu’une souris USB externe est connectée. Pour désactiver le pavé tactile : 1. Sélectionnez cette option sous Windows, dans Panneau de Configuration > Matériel et audio > Souris. 2. Sélectionnez l’onglet ELAN. 3. Cochez l’option Disable when external pointing device plug in (Désactiver le dispositif de pointage interne lorsqu’un périphérique de pointage externe est connecté). 4.
Périphériques de stockage Les périphériques de stockage permettent au portable de lire et d’écrire des documents, des images ou d’autres fichiers sur différents supports de stockage. Lecteur optique (sur une sélection de modèles) Insérer un disque optique 1. Alors que le portable est allumé, pressez le bouton d’éjection du lecteur de disque. Le tiroir s’éjectera partiellement. 2. Tirez délicatement sur la face avant du lecteur et faites complètement glisser le tiroir vers l’extérieur.
3. Prenez le disque par les côtés, face imprimée vers le haut. Appuyez des deux côtés du centre du disque jusqu’à ce qu’il s’enclenche sur le moyeu. Le moyeu doit être plus haut que le disque lorsqu’il est correctement installé. 4. Refermez lentement le tiroir du lecteur de disque. Le lecteur commence à lire la table des matières (TOC) du CD. Lorsque le lecteur s’arrête, le CD est prêt à l’emploi. Il est normal d’entendre et de sentir le CD tourner rapidement lorsque le lecteur lit les données.
Retirer un disque optique Ejectez le tiroir et soulevez délicatement le bord du disque vers le haut jusqu’à ce qu’il se désolidarise du lecteur. Ejection d’urgence L’éjection d’urgence est située dans une ouverture sur le lecteur optique, et sert à éjecter le tiroir du lecteur lorsque l’éjection électronique ne fonctionne pas. N’utilisez pas l’éjection d’urgence à la place de l’éjection électronique. Faites attention à ne pas érafler le témoin d’activité qui est situé dans la même zone.
Utiliser le lecteur optique Les disques optiques et les équipements doivent être manipulés avec soin pour préserver les mécanismes de précision qu’ils mettent en oeuvre. Respectez scrupuleusement les consignes des fabricants de CD. Contrairement au lecteur d’un PC de bureau, celui du portable utilise un moyeu qui maintient le CD en place quelle que soit l’inclinaison.
Lecteur de carte mémoire Flash Normalement un lecteur de cartes mémoire doit être acheté séparément pour pouvoir utiliser des cartes mémoire provenant de périphériques comme les appareils photo numériques, les lecteurs MP3, les téléphones portables et les PDA. Ce PC portable possède un lecteur de cartes mémoire intégré permettant de lire plusieurs types de cartes mémoires comme illustré dans l’ exemple ci-dessous.
Disque dur Les disques durs possèdent des capacités supérieures et fonctionnent à des vitesses plus grandes que les lecteurs de disquette et de CD-ROM. Le portable est livré avec un disque dur amovible. Les disques durs actuels supportent la technologie (Self Monitoring and Reporting Technology) qui détectent les erreurs ou les pannes du disque dur avant qu’elles n’arrivent. Lorsque vous remplacez ou mettez à niveau votre disque dur, faîtes appel à un centre d’intervention agréé ou au revendeur de ce PC.
Localiser le(s) disque(s) dur(s) : Retirer le(s) disque(s) dur(s) : 1 1 2 2 2 2 1 1 1 1 2 2 64 Manuel d’utilisation pour ordinateur portable
Installer le(s) disque(s) dur(s) : 2 1 2 2 1 2 1 Manuel d’utilisation pour ordinateur portable 65
Mémoire (RAM) L’ajout de mémoire supplémentaire permet d’accroître les performances des applications en réduisant le temps d’accès au disque. Achetez des modules mémoire uniquement auprès d’un revendeur agréé pour assurer une fiabilité et une compatibilité optimale. Renseignez-vous auprès d’un centre agréé pour plus d’informations sur l’ajout de mémoire sur votre PC portable.
Connexions Ni le modem ni le contrôleur réseau intégrés ne peuvent être ajoutés après l’achat. Ils peuvent toutefois être installés sous forme de carte d’extension. Connexion réseau Connectez un câble réseau, doté de connecteurs RJ-45 à chaque extrémité, l’un sur le port modem/réseau du portable et l’autre à un hub ou un switch. Pour les vitesses 100/1000BASE-TX, votre câble réseau doit être de catégorie 5 (non catégorie 3) à paire torsadée.
Câble à paires torsadées Le câble qui sert à relier une carte Ethernet à un hôte (en général hub ou switch) est appelé TPE (paires torsadées pour Ethernet). Les connecteurs en bout de câble s’appellent RJ-45, et ne sont pas compatibles avec les connecteurs téléphoniques RJ-11. Si vous souhaitez connectez deux ordinateurs sans passer par un hub, un câble réseau croisé est requis. Les modèles Gigabit supporte l’auto-crossover (croisement automatique), donc un câble Ethernet croisé est facultatif.
Connexion sans fil (sur certains modèles) L’option sans fil intégrée (en option) utilise un adaptateur Ethernet sans fil compact et facile d’utilisation. Intégrant le standard IEEE 802. Le module sans fil intégré offre un débit de transmission de données élevé, grâce aux technologies Direct Sequence Spread Spectrum (DSSS) et Octogonal Frequency Division Multiplexing (OFDM), toutes deux sur une fréquence de 2.4 GHz / 5GHz. Le module réseau sans fil est rétro-compatible avec l’ancien standard IEEE 802.
Mode Ad-hoc Le mode Ad-hoc permet au portable de se connecter à un autre périphérique sans fil. Aucun point d’accès n’est nécessaire dans cet environnement sans fil. (Tous les périphériques doivent être pourvus d’un adaptateur LAN sans fil 802.11, en option) PC portable PC de bureau PDA Mode Infrastructure Le mode Infrastructure permet au portable et à d’autres périphériques sans fil de rejoindre un réseau sans fil créé par un point d’accès (vendu séparément).
Connexion réseau sans fil Windows Se connecter à un réseau 1. Si nécessaire, activez la fonction sans fil de voter PC portable (voir les interrupteurs au chapitre 3). 2. Appuyez plusieurs fois [FN + F2] jusqu’à ce que l’icône Wireless LAN et Bluetooth s’affiche. Ou double-cliquez sur l’icône Wireless Console de la barre des tâches, puis sélectionnez l’icône Wireless LAN. 3. Faites un clic droit sur l'icône réseau avec une étoile orange située sur la barre de tâches de Windows®. 4.
5. Un mot de passe peut vous être demandé pour vous connecter. 6. Une fois la connexion établie, celle-ci s'affiche dans la liste. 7. Vous pouvez voir apparaître l'icône de réseau sans fil la zone de notification. dans L'icône de connexion sans fil barrée apparaît lorsque vous appuyez sur + pour désactiver la fonction sans fil.
Connexion Bluetooth (sur une sélection de modèles) Grâce à la technologie Bluetooth, les PC portables n’ont plus besoin de recourir à des câbles pour connecter des périphériques ayant une connexion Bluetooth active ; par exemple, des PC portables, des PC de bureau, des téléphones portables, ou des PDA. Si votre portable n’intègre pas la technologie Bluetooth, vous devez connecter un module USB ou carte PC Bluetooth afin de pouvoir utiliser cette technologie.
Ou double-cliquez sur l’icône de Wireless Console située dans la barre des tâches de Windows et sélectionnez l’icône Bluetooth. 3. Depuis le Panneau de configuration, allez dans Réseau et Internet > Centre Réseau et partage puis cliquez sur Modifier les paramètres de la carte dans la colonne de gauche. 4. Faites un clic droit sur Connexion Réseau Bluetooth et sélectionnez Afficher les périphériques réseau Bluetooth. 5. Cliquez sur Ajouter un périphérique pour rechercher des nouveaux périphériques.
6. Sélectionnez un périphérique compatible Bluetooth dans la liste puis cliquez sur Suivant. 7. Saisissez le code de sécurité Bluetooth sur votre périphérique et lancez le pairage. 8. Le pairage est établit avec succès. Cliquez sur Fermer pour terminer la configuration.
USB Charger+ USB Charger+ permet de recharger les appareils USB compatibles avec la norme BC 1.1 (Battery Charging v1.1) que l’ordinateur soit allumé ou éteint. Vous pouvez déterminer le seuil d’arrêt de charge de la batterie en fonction de vos besoins. Avec adaptateur USB Charger+ est toujours disponible sur le port USB 3.0 lorsque votre ordinateur est relié à son adaptateur secteur. Sans adaptateur Pour activer USB Charger+ : 1.
A Appendice
Accessoires optionnels Ces éléments sont optionnels et destinés à compléter votre portable. Hub USB (Optionnel) Connecter un hub USB (optionnel) permet d’augmenter le nombre de ports USB et de connecter ou déconnecter rapidement de nombreux périphériques USB via un câble unique. Mémoire Flash USB Une mémoire Flash USB peut remplacer le lecteur de disquette 1.44Mo en vous offrant jusqu’à 1 Go de stockage, une plus grande vitesse de transfert et une meilleure fiabilité.
Système d’exploitation et logiciels Ce PC portable peut offrir (en fonction du territoire) le choix d’un système d’exploitation pré-installé tel que Microsoft Windows XP. Les choix et les langues dépendent du territoire. Le niveau de support matériel et logiciel peut varier en fonction du système d’exploitation installé. La stabilité et la compatibilité avec d’autres systèmes d’exploitation ne peuvent être garanties.
Paramètres du BIOS Boot Device (Périphérique de démarrage) 1. Dans le menu Boot, sélectionnez l’élément Boot Option #1. Main Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced Chipset Boot Security Save & Exit Boot Configuration UEFI Boot Launch PXE OpROM [Enabled] [Disabled] Boot Boot Boot Boot [P0: WDC WD7500BPKT...] [P2: MATSHITABD-MLT...
Security Setting (Paramètres de sécurité) Main Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced Boot Security Save & Exit If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the user’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup, the User will have Administrator rights.
I/O Interface Security (Sécurité de l’interface d’E/S) Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Security If Locked, 2nd SATA HDD will be disabled. I/O Interface Security LAN Network Interface Wireless Network Interface HD AUDIO Interface SATA ODD Interface USB Interface Security [UnLock] [UnLock] [UnLock] [UnLock] LAN Network Interface Lock UnLock : Select Screen : Select Item Enter: Select +/—: Change Opt.
USB Interface Security (Sécurité de ‘interface USB) Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Security If Locked, all USB device will be disabled. USB Interface Security USB Interface [UnLock] External Ports BlueTooth CMOS Camera Card Reader [UnLock] [UnLock] [UnLock] [UnLock] USB Interface LocK UnLock : Select Screen : Select Item Enter: Select +/—: Change Opt. F1: General Help F9: Optimized Defaults F10: Save ESC: Exit Version 2.01.1208.
HDD Password (Mot de passe d’accès au disque dur) Main Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced Boot Security Save & Exit If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the user’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup, the User will have Administrator rights.
Save Changes (Enregistrer les modifications) Si vous souhaitez garder les paramètres de votre configuration, vous devez les enregistrer avant de quitter le BIOS. Si vous souhaitez restaurer les paramètres par défaut, sélectionnez Restore Defaults. Vous devez ensuite enregistrer cette modification avant de quitter le BIOS. Main Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Problèmes fréquents et solutions Problème matériel - Lecteur optique Le lecteur optique ne parvient plus à lire ou à écrire des disques. 1. Mettez à jour le BIOS vers la version la plus récente, puis réessayez. 2. Si la mise à jour du BIOS ne résout pas le problème, utilisez des disques de meilleure qualité, puis réessayez. 3. Si le problème persiste, contactez votre centre de réparation local, et recherchez l’assistance d’un technicien.
Problème matériel - Caméra intégrée La caméra intégrée ne fonctionne pas correctement. 1. Vérifiez dans le “Gestionnaire de périphériques” s’il n’y a aucun problème. 2. Réinstallez le pilote de la caméra pour résoudre ce problème. 3. Si le problème n’est toujours pas résolu, mettez à jour le BIOS vers la version la plus récente, puis réessayez. 4. Si le problème persiste, contactez votre centre de réparation local, et recherchez l’assistance d’un technicien.
Symptômes & Solutions : A. Le problème peut être localisé au niveau de la carte mère, du disque dur, ou du PC portable ; faîtes appel à votre centre d’intervention local pour obtenir une assistance. B. Pour les problèmes causés par votre système d’exploitation, essayez de restaurer votre système en utilisant la partition ou le disque de restauration. IMPORTANT : Vous devez d’abord sauvegarder toutes vos données avant de lancer la restauration du système. C.
AVERTISSEMENT : Ne vous connectez pas à Internet avant d’avoir installé un utilitaire anti-virus et un pare-feu afin de protéger le système des virus. Problème logiciel - Logiciels fournis par ASUS Lors de la mise sous tension du PC portable, un message d’erreur “Open policy file error” s’affiche. A. Réinstallez la version la plus récente de l’utilitaire “Power4 Gear” afin de résoudre ce problème. Elle est disponible sur le site Web ASUS.
5. Si le problème n’est toujours pas résolu, procédez à une restauration du système pour une réinstallation complète de ce dernier. IMPORTANT : Vous devez impérativement sauvegarder vos données à un autre emplacement avant de procéder à la restauration. AVERTISSEMENT : Ne vous connectez pas à Internet avant d’avoir installé un utilitaire anti-virus et un pare-feu afin de protéger le système des virus.
Problème logiciel - BIOS Mettre à jour le BIOS. 1. Vérifiez scrupuleusement le modèle du PC portable, et téléchargez sur le site Web ASUS le BIOS le plus récent pour votre modèle et sauvegardez-le sur une clé USB. 2. Connectez votre clé USB au PC portable et allumez le PC. 3. Utilisez la fonction “Start Easy Flash” de la page “Advanced” (Avancé) du BIOS. Suivez les instructions à l’écran. Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Restaurer votre ordinateur portable Utiliser la partition de restauration La partition de restauration permet de restaurer les logiciels de votre PC portable à leur état de fonctionnement initiale. Avant d’utiliser la partition de restauration, copiez vos données (telles que les fichiers PST de Outlook) vers un périphérique de stockage USB ou un lecteur réseau, et veillez à noter vos configurations personnalisées (telles que votre configuration réseau).
Recover Windows to entire HD. Cette option supprimera toutes les partitions de votre disque dur, et créera une nouvelle partition système (lecteur “C”). Recover Windows to entire HD with 2 partition. Cette option supprimera toutes les partitions de votre disque dur, et créera deux nouvelles partitions : “C” (40%) et “D” (60%). 6. Suivez les instructions à l’écran pour terminer la procédure de restauration. Veuillez vous rendre sur le site www.asus.
Utiliser le DVD de restauration : 1. Insérez le DVD de Restauration dans le lecteur optique. Le PC portable doit être SOUS TENSION. 2. Redémarrez le PC portable, et pressez au démarrage, puis sélectionnez le lecteur optique (apparaît normalement comme “CD/DVD”) grâce au curseur. Appuyez ensuite sur pour démarrer à partir du DVD de Restauration. 3. Sélectionnez OK pour lancer la restauration de l’image. 4. Sélectionnez OK pour confirmer la restauration du système.
Informations sur le lecteur de DVD-ROM Le portable est livré avec lecteur de DVD-ROM ou lecteur de CDROM. Pour visionner des films DVD, vous devez installer le logiciel de décompression MPEG2 et le logiciel de lecture DVD présent sur le CD des pilotes. Le lecteur de DVD-ROM permet de lire les CD comme les DVD. Information sur le zonage La lecture de films DVD implique un décodage vidéo MPEG2, audio numérique AC3 et le décodage d’éléments de protection CSS.
Définition des zones Zone 1 Canada, Etats-Unis, territoires des Etats-Unis Zone 2 République Tchèque, Egypte, Finlande, France, Allemagne, Etats du Golf, Hongrie, Islande, Iran, Iraq, Irlande, Italie, Japon, Pays-Bas, Norvège, Pologne, Portugal, Arabie Saoudite, Ecosse, Afrique du Sud, Espagne, Suède, Suisse, Syrie, Turquie, RU, Grèce, Ex-Yougoslavie, Slovaquie Zone 3 Birmanie, Indonésie, Corée du Sud, Malaisie, Philippines, Singapour, Taiwan, Thaïlande, Vietnam Zone 4 Australie, Caraïbes (Sauf territoires
Information sur le lecteur de Blu-ray� (sur une sélection de modèles) Définition des zones Région A Pays d'Amérique du nord, du centre et du sud ainsi que leurs territoires respectifs, Taiwan, Hong Kong, Macao, Japon, Corée (sud et nord), pays d'Asie du sud-est ainsi que leurs territoires respectifs. Région B Pays d'Europe, d'Afrique et d'Asie du sud-ouest ainsi que leurs territoires respectifs, Australie et Nouvelle-Zélande.
Conformité du modem interne Le PC portable avec modem interne est conforme aux normes JATE (Japon), FCC (US, Canada, Corée, Taiwan), et CTR21. Le modem interne a été approuvé conformément à la Décision du Conseil 98/482/EC comme terminal de connexion pan-européen unique compatible au réseau PSTN (public switched telephone network/réseau téléphonique public commuté).
Déclaration de compatibilité au réseau Déclaration qui doit être faite par le fabricant à l’utilisateur: “Cette déclaration indiquera les réseaux avec lesquels l’équipement est conçu pour fonctionner et tout réseau notifié avec lequel l’équipement peut avoir des difficultés d’interopérabilité. Le fabricant doit également joindre une déclaration qui établit clairement où la compatibilité au réseau est dépendante des paramètrages physiques ou logiciels.
Ce tableau indique les pays où s’applique le standard CTR21.
Ces informations ont été reprises du CETECOM et sont données sans engagement. Pour la mise à jour de ce tableau, vous pouvez consulter http://www.cetecom.de/technologies/ctr_21.html 1 Les exigences nationales ne s’appliquent que si l’équipement peut utiliser la tonalité par impulsion (les fabricants peuvent alors déclarer dans leur manuel que l’équipement n’est conçu que pour le support DTMF, ce qui rendrait tout test supplémentaire superflu).
Déclarations et avertissements de Sécurité Rapport de la Commission Fédérale des Communications Ce dispositif est conforme à l’alinéa 15 des règles établies par la FCC. L'opération est sujette aux deux conditions suivantes : • Ce dispositif ne peut causer d'interférence nuisible, et • Ce dispositif se doit d'accepter toute interférence reçue, y compris celles pouvant causer des résultats indésirables.
(Réimprimé à partir du Code des Régulations Fédérales #47, section 15.193, 1993. Washington DC: Office of the Federal Register, National Archives and Records Administration, U.S. Government Printing Office.) Directives FCC concernant l’exposition aux fréquences radio Toute modification qui n’a pas été approuvée par l’instance en charge de la conformité peut rendre nul le droit d’usage de cet appareil par l’utilisateur.
Label CE Label CE pour les appareils sans fonction réseau sans fil / Bluetooth intégrée Cet appareil est conforme aux directives 2004/108/EC sur la “Compatibilité électromagnétique” et 2006/95/EC sur les “Faibles tensions”. Label CE pour les appareils avec fonction réseau sans fil / Bluetooth intégrée Cet appareil est conforme aux directives 1999/5/EC du parlement et de la commission Européenne votées le 9 Mars 1999 concernant la conformité des équipements Radio et de Télécommunications.
Canaux d’opérations sans fil régionaux Amérique du N. Japon Europe ETSI 2.412-2.462 GHz 2.412-2.484 GHz 2.412-2.472 GHz Ch01 à travers CH11 Ch01 à travers Ch14 Ch01 à travers Ch13 Restriction des bandes de fréquences sans fil (France) Certains lieux en France ont une bande de fréquence restreinte. Les puissances domestiques maximum autorisées dans les plus mauvais cas sont : • 10mW pour l’ensemble de la bande 2.4 GHz(2400 MHz–2483.5 MHz) • 100mW pour les fréquences entre 2446.5 MHz et 2483.
60 Oise 61 Orne 63 Puy du Dôme 64 Pyrénées Atlantique 66 Pyrénées Orientales 67 Bas Rhin 68 Haut Rhin 70 Haute Saône 71 Saône et Loire 75 Paris 82 Tarn et Garonne 84 Vaucluse 88 Vosges 89 Yonne 90 Territoire de Belfort 94 Val de Marne Ces conditions sont susceptibles de changer dans le futur, vous permettant d’utiliser votre carte réseau sans fil dans un plus grand nombre de régions en France.
Notes de sécurité UL Requis pour la norme UL 1459 couvrant les équipements de communication (téléphone) prévus pour être connectés de manière électrique à un réseau de télécommunication ayant un voltage d’opération à la terre n’excédant pas 200V, 300V et 105V rms, ou installés, utilisés en conformité avec les normes du NEC (National Electrical Code) (NFPA 70).
Normes de sécurité liées à l’alimentation Les produits utilisant plus de 6 A et pesant plus de 3 Kg doivent utiliser des cordons d’alimentation supérieurs ou égaux à: H05VV-F, 3G, 0.75 mm2 ou H05VV-F, 2G, 0.75 mm2. REACH En accord avec le cadre réglementaire REACH (Enregistrement, Evaluation, Autorisation, et Restriction des produits chimiques), nous publions la liste des substances chimiques contenues dans nos produits sur le site ASUS REACH : ���������������������������� http://csr.asus.
Mise en garde (pour les PC portables avec batterie Lithium-Ion) CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. (English) ATTENZIONE! Rischio di esplosione della batteria se sostituita in modo errato. Sostituire la batteria con un una di tipo uguale o equivalente consigliata dalla fabbrica. Non disperdere le batterie nell’ambiente.
Informations de Sécurité relatives au lecteur de disque optique Informations de Sécurité relatives au Laser Les lecteurs de disque optique internes ou externes vendus avec ce PC portable contiennent un PRODUIT LASER DE CLASSE 1. Les classifications laser peuvent être retrouvées dans le glossaire situé à la fin de ce manuel utilisateur. ATTENTION : Effectuer des réglages ou réaliser des manipulations autres que celles spécifiées dans le manuel utilisateur peut provoquer une exposition dangereuse au laser.
Note relative aux produits de Macrovision Corporation Ce produit comprend une technologie de protection de copyright protégée par certains brevets déposés aux U.S.A. et autres propriétés intellectuelles appartenant à Macrovision Corporation et à d’autres. L’utilisation de cette technologie doit être autorisée par Macrovision Corporation, et n’est destinée qu’à un usage familial ou autres usages limités de même sorte, à moins d’une autorisation par Macrovision Corporation.
Aggrément CTR 21 (pour les PC portables avec modem intégré) Danish Dutch English Finnish French German Greek Italian Portuguese A-36 Manuel d’utilisation pour ordinateur portable
Spanish Swedish Manuel d’utilisation pour ordinateur portable A-37
Label écologique de l’Union Européenne Ce portable a reçu le label Flower de l’Union Européenne couvrant les critères suivants : 1. Consommation d’énergie diminuée en opération et en veille. 2. Utilisation limitée de métaux lourds toxiques. 3. Utilisation limitée de substances nocives pour l’environnement ou la santé. 4. Réduction de l’utilisation des ressources naturelles en encourageant le recyclage. 5.
Déclaration de conformité aux normes environnementales internationales ASUS développe une conception écologique pour tous ses produits et s’assure que des standards élevés en terme de protection de l’environnement sont respectés tout au long du processus de fabrication. De plus, ASUS met à votre disposition des informations sur les différentes normes de respect de l’environnement. Consultez le lien http://csr.asus.com/english/Compliance.
Informations sur les droits d’auteur Aucune partie du présent manuel, y compris les produits et logiciels qui y sont décrits, ne peut être reproduite, transmise, transcrite, stockée dans un système de base de données, ni traduite dans aucune langue, sous une quelconque forme et par tout moyen, hormis la documentation conservée par l’acheteur à des fins de sauvegarde, sans la permission expresse de ASUSTeK COMPUTER INC. (“ASUS”).
Clause de responsabilité limitée Des dommages peuvent survenir suite à un défaut sur une pièce fabriquée par ASUS ou un tiers. Vous avez le droit à des dommages et intérêts auprès d’ASUS.
EC Declaration of Conformity We, the undersigned, Manufacturer: ASUSTeK COMPUTER INC. Address, City: No. 150, LI-TE RD., PEITOU, TAIPEI 112, TAIWAN R.O.C. Country: TAIWAN Authorized representative in Europe: ASUS COMPUTER GmbH Address, City: HARKORT STR.