User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- Chapter 3: Powering Up
- Chapter 4: BIOS Setup
- 4.1 Managing and updating your BIOS
- 4.2 BIOS setup program
- 4.3 Main menu
- 4.4 Advanced menu
- 4.4.1 CPU Configuration
- 4.4.2 Power & Performance
- 4.4.3 Server ME Configuration
- 4.4.4 System Event Log
- 4.4.5 Trusted Computing
- 4.4.6 Redfish Host Interface Settings
- 4.4.7 Onboard LAN Configuration
- 4.4.8 Serial Port Console Redirection
- 4.4.9 Intel TXT Information
- 4.4.10 SIO Configuration
- 4.4.11 PCI Subsystem Settings
- 4.4.12 USB Configuration
- 4.4.13 Network Stack Configuration
- 4.4.14 CSM (Compatibility Support Module)
- 4.4.15 NVMe Configuration
- 4.4.16 APM Configuration
- 4.4.17 Third-party UEFI driver configurations
- 4.5 Chipset menu
- 4.6 Security menu
- 4.7 Boot menu
- 4.8 Monitor menu
- 4.9 Tool menu
- 4.10 Event Logs menu
- 4.11 Server Mgmt menu
- 4.12 Exit menu
- Chapter 5: RAID Configuration
- Chapter 6: Driver Installation
- Appendix
ASUS P12R-M Series
4-23
PCI Latency Timer [32 PCI Bus Clocks]
Allows you to set the value to be programmed into PCI Latency Timer Register.
Configuration options: [32 PCI Bus Clocks] [64 PCI Bus Clocks] [96 PCI Bus Clocks] [128 PCI
Bus Clocks] [160 PCI Bus Clocks] [192 PCI Bus Clocks] [224 PCI Bus Clocks] [248 PCI Bus
Clocks]
PCI-X Latency Timer [64 PCI Bus Clocks]
Allows you to set the value to be programmed into PCI Latency Timer Register.
Configuration options: [32 PCI Bus Clocks] [64 PCI Bus Clocks] [96 PCI Bus Clocks] [128 PCI
Bus Clocks] [160 PCI Bus Clocks] [192 PCI Bus Clocks] [224 PCI Bus Clocks] [248 PCI Bus
Clocks]
VGA Palette Snoop [Disabled]
Allows you to enable or disable VGA Palette Registers Snooping.
Configuration options: [Disabled] [Enabled]
4.4.11 PCI Subsystem Settings
Allows you to configure PCI, PCI-X, and PCI Express Settings.
The following item appears only when
Use This Device
is set to
[Enabled]
.
Disabling SIO Logical Devices may have unwanted side effects. PROCEED WITH
CAUTION.
Possible: [Use Automatic Settings]
Allows the user to change the device resource settings. New settings will be reflected
no this setup page after system restarts.
Configuration options: [Use Automatic Settings] [IO=3F8h; IRQ=4; DMA;] [IO=3F8h;
IRQ=3, 4, 5, 7, 9, 10, 11, 12; DMA;] [IO=2F8h; IRQ=3, 4, 5, 7, 9, 10, 11, 12; DMA;]
[IO=3E8h; IRQ=3, 4, 5, 7, 9, 10, 11, 12; DMA;] [IO=2E8h; IRQ=3, 4, 5, 7, 9, 10, 11, 12;
DMA;]