User Guide Motherboard P4P800 Deluxe
E1323 Revised Edition V3 May 2003 Copyright © 2003 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents FCC/CDC statements ..................................................................... vi Safety information ......................................................................... vii About this guide ............................................................................ viii How this guide is organized ................................................ viii Conventions used in this guide ............................................. ix Where to find more information ......................
Contents Chapter 3: Powering up 3.1 3.2 3.3 Starting up for the first time ................................................ 3-1 Vocal POST Messages ...................................................... 3-2 Powering off the computer ................................................. 3-4 Chapter 4: BIOS setup 4.1 4.2 4.3 4.4 4.5 iv Managing and updating your BIOS .................................... 4-1 4.1.1 Creating a bootable floppy disk ............................. 4-1 4.1.
Contents 4.6 4.7 4.5.6 APM Configuration ............................................... 4-28 4.5.7 Hardware Monitor ................................................ 4-30 Boot menu ........................................................................ 4-32 4.6.1 Boot Device Priority ............................................. 4-32 4.6.2 Hard disk drives ................................................... 4-33 4.6.3 Boot Settings Configuration ................................. 4-33 4.6.4 Security .....
FCC/CDC statements Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing the ASUS P4P800 Deluxe motherboard. How this guide is organized This manual contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the P4P800 Deluxe motherboard. It includes brief descriptions of the special attributes of the motherboard and the new technology it supports.
Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Information that you MUST follow to complete a task. NOTE: Tips and additional information to aid in completing a task.
ASUS contact information ASUSTeK COMPUTER INC. (Asia-Pacific) Address: General Tel: General Fax: General Email: 150 Li-Te Road, Peitou, Taipei, Taiwan 112 +886-2-2894-3447 +886-2-2894-3449 info@asus.com.tw Technical Support MB/Others (Tel): Notebook (Tel): Desktop/Server (Tel): Support Fax: Web Site: +886-2-2890-7121 (English) +886-2-2890-7122 (English) +886-2-2890-7123 (English) +886-2-2890-7698 www.asus.com.
P4P800 Deluxe specifications summary CPU CPU Socket 478 for Intel® Pentium® 4 / Celeron up to 3.
P4P800 Deluxe specifications summary Special Rear Panel features I/O 1 x Parallel port 1 x Serial ports 1 x PS/2 keyboard port 1 x PS/2 mouse port 4 x USB 2.0/USB 1.1 ports 1 x RJ-45 port (optional) 1 x S/PDIF-out port 1 x IEEE 1394 port Line In/Line Out/Microphone ports Internal I/O 2 x USB 2.0/1.
Chapter 1 This chapter describes the features of the P4P800 Deluxe motherboard. It includes brief explanations of the special attributes of the motherboard and the new technology it supports.
Chapter summary 1.1 Welcome! ........................................................ 1-1 1.2 Package contents .......................................... 1-1 1.3 Special features ............................................. 1-2 1.4 Motherboard overview ...................................
1.1 Welcome! Thank you for buying the ASUS® P4P800 Deluxe motherboard! The ASUS P4P800 Deluxe motherboard delivers a host of new features and latest technologies making it another standout in the long line of ASUS quality motherboards! The P4P800 Deluxe incorporates the Intel® Pentium® 4 Processor in 478pin package coupled with Intel® 82865PE and ICH5R chipsets that support the fastest 800MHz FSB to set a new benchmark for an effective desktop platform solution.
1.3 Special features 1.3.1 Product highlights Latest processor technology The P4P800 Deluxe motherboard supports the latest Intel® Pentium® 4 / Celeron Processor via a 478-pin surface mount ZIF socket. The Pentium 4 processor with 512KB L2 cache on 0.13 micron processor includes a 800/ 533/400 MHz system bus and the FMB2 power design that allows up to 3.06+ GHz core frequencies and Intel® Prescott CPU when available. See page 2-4 for more information.
Ai Audio solution The SoundMAX-class ADI AD1985 AC ‘97 audio CODEC supports 6-channel 5.1 surround sound output, stereo microphone input, variable sample rate conversion (SRC), professional quality 103-dB out put with 94-dB SNR, and analog enumeration capability. The SoundMAX 4 XL software features the AudioESP™ (Audio Enumeration and Sensing Process) that allows intelligent detection of the peripherals plugged into the audio ports and identifies the incompatible devices, if any.
C.P.R. (CPU Parameter Recall) The C.P.R. feature of the motherboard BIOS allows automatic re-setting to the BIOS default settings in case the system hangs due to overclocking. When the system hangs due to overclocking, C.P.R. eliminates the need to open the system chassis and clear the RTC data. Simply shut down and reboot the system, and BIOS automatically restores the CPU default setting for each parameter.
AI Overclocking This feature allows convenient overclocking up to 30% (depending on the installed CPU and DRAM) to enhance system performance while still maintaining system stability. See section “4.4.1 JumperFree Configuration” to set the BIOS items for overclocking. ASUS Q-Fan technology The ASUS Q-Fan technology smartly adjusts the fan speeds according to the system loading to ensure quiet, cool, and efficient operation. See details on page 4-30.
1.3.2 Value-added solutions Overclocking • adjustable CPU frequency multiple in BIOS using the ASUS JumperFree™ solution • C.P.R. (CPU Parameter Recall) • adjustable CPU VCORE , and DDR memory and AGP voltages • Stepless Frequency Selection (SFS) for fine-tuning system bus frequency from 100MHz up to 400MHz at 1MHz increments Temperature, fan, and voltage monitoring The CPU temperature is monitored by the Winbond ASIC to prevent overheating and damage.
1.4 Motherboard overview Before you install the P4P800 Deluxe motherboard, familiarize yourself with its physical configuration and available features to facilitate the motherboard installation and future upgrades. A sufficient knowledge of the motherboard specifications will also help you avoid mistakes that may damage the board and its components. 1.4.1 Major components The following are the major components of the P4P800 Deluxe motherboard as pointed out in the picture on page 1-7. 1.
1 2 3 4 5 6 7 8 9 21 10 20 19 18 17 22 16 23 15 14 24 13 12 11 25 26 27 28 33 1-8 32 31 30 29 Chapter 1: Product introduction
1.4.2 Core specifications 1 ATX 12V connector. This power connector connects the 4-pin 12V plug from the ATX 12V power supply. 2 CPU socket. A 478-pin surface mount, Zero Insertion Force (ZIF) socket for the Intel® Pentium® 4 Processor (and Intel’s future Prescott CPU) support with 800/533/400 MHz system bus that allows up to 6.4GB/s data transfer rates. 3 North bridge controller.
12 RAID connector. These dual-channel bus master IDE connectors support Ultra DMA/133 IDE devices. These connectors are slotted to prevent incorrect insertion of the IDE ribbon cable. 13 Flash ROM. This 4Mb firmware contains the programmable BIOS program. 14 South bridge controller. The Intel® ICH5R is a subsystem that integrates various I/O functions including 2-channel ATA100 bus master IDE controller, SATA RAID controller, up to eight USB 2.0/1.1 ports, I/O APIC, AC’97 2.2 interface, and PCI 2.
23 Parallel port. This 25-pin port connects a parallel printer, a scanner, or other devices. 24 IEEE1394 port. This 6-pin IEEE 1394 port provides high-speed connectivity for audio/video devices, storage peripherals, other PCs and/or portable devices. 25 RJ-45 port. This port allows connection to a Local Area Network (LAN) through a network hub. 26 Line In jack. This Line In (light blue) jack connects a tape player or other audio sources.
1-12 Chapter 1: Product introduction
Chapter 2 This chapter describes the hardware setup procedures that you have to perform when installing system components. It includes details on the switches, jumpers, and connectors on the motherboard.
Chapter summary 2.1 Motherboard installation ............................... 2-1 2.2 Motherboard layout ....................................... 2-2 2.3 Before you proceed ....................................... 2-3 2.4 Central Processing Unit (CPU) ..................... 2-4 2.5 System memory ........................................... 2-10 2.6 Expansion slots ........................................... 2-15 2.7 Jumpers ........................................................ 2-20 2.
2.1 Motherboard installation Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. The P4P800 Deluxe uses the ATX form factor that measures 12 inches x 9.6 inches. Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so may cause you physical injury and damage motherboard components. 2.1.
2.2 Motherboard layout 24.5cm (9.6in) Top:Line In Center:Line Out Below:Mic In Accelerated Graphics Port (AGP1) FLOPPY1 30.5cm (12.0in) USB2.
2.3 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. 1. Unplug the power cord from the wall socket before touching any component. 2. Use a grounded wrist strap or touch a safely grounded object or to a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity. 3. Hold components by the edges to avoid touching the ICs on them. 4.
2.4 Central Processing Unit (CPU) 2.4.1 Overview The motherboard comes with a surface mount 478-pin Zero Insertion Force (ZIF) socket. The socket is designed for the Intel® Pentium® 4 Processor in the 478-pin package with 512KB L2 cache on 0.13 micron process. This processor includes the Intel® NetBurst™ micro-architecture that features the rapid execution engine, Intel® Hyper-Threading Technology, 800/533/400MHz system bus, and execution trace cache.
2.4.2 Installing the CPU Follow these steps to install a CPU. 1. Locate the 478-pin ZIF socket on the motherboard. 2. Unlock the socket by pressing the lever sideways, then lift it up to a 90°-100° angle. Socket Lever 90 - 100 Make sure that the socket lever is lifted up to 90°-100° angle, otherwise the CPU does not fit in completely.
3. Position the CPU above the socket such that its marked corner matches the base of the socket lever. 4. Carefully insert the CPU into the socket until it fits in place. Gold Mark The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to prevent bending the pins and damaging the CPU! 5. When the CPU is in place, push down the socket lever to secure the CPU. The lever clicks on the side tab to indicate that it is locked.
2.4.3 Installing the heatsink and fan The Intel® Pentium® 4 Processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. When you buy a boxed Intel Pentium 4 Processor, the package includes the heatsink, fan, and retention mechanism. In case you buy a CPU separately, make sure that you use only Intel certified heatsink and fan. Follow these steps to install the CPU heatsink and fan. 1.
2. Position the fan with the retention mechanism on top of the heatsink. Align and snap the four hooks of the retention mechanism to the holes on each corner of the module base. Make sure that the fan and retention mechanism assembly perfectly fits the heatsink and module base, otherwise you cannot snap the hooks into the holes. Retention Hole Retention Lock Retention Hook Snapped to the Retention Hole Keep the retention locks lifted upward while fitting the retention mechanism to the module base.
3. Push down the locks on the retention mechanism to secure the heatsink and fan to the module base. When secured, the retention locks should point to opposite directions. 2.4.4 Connecting the CPU fan cable When the fan, heatsink, and the retention mechanism are in place, connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN. CPU Fan Connector (CPU_FAN) Don’t forget to connect the CPU fan connector! Hardware monitoring errors may occur if you fail to plug this connector.
2.5 System memory 2.5.1 Overview The motherboard comes with four Double Data Rate (DDR) Dual Inline Memory Module (DIMM) sockets. These sockets support up to 4GB system memory using 184-pin unbuffered non-ECC PC3200/2700/PC2100 DDR DIMMs and allow up to 6.4 GB/s data transfer rate. 80 Pins DIMM_B2 DIMM_B1 DIMM_A2 DIMM_A1 The following figure illustrates the location of the DDR DIMM sockets.
2.5.2 Memory configurations You may install 64MB, 128MB, 256MB, 512MB, and 1GB DDR DIMMs into the DIMM sockets using the memory configurations in this section. Important notes on memory configurations 1. Installing DDR DIMMs other than the recommended configurations may cause memory sizing error or system boot failure. Use any of the recommended configurations in Table 1. 2. In dual-channel configurations, install only identical (the same type and size) DDR DIMM pairs for each channel. 3.
Table 1 Recommended memory configurations Sockets DIMM_A1 DIMM_A2 DIMM_B1 DIMM_B2 Mode Single-channel Dual-channel* (1) Populated — — — (2) — Populated — — (3) — — Populated — (4) — — — Populated — Populated — (1) Populated (2) — Populated — Populated (3) Populated Populated Populated Populated * Use only identical DDR DIMM pairs.
2.5.2.2 DDR Qualified Vendor List The following table lists the PC3200 (DDR400) memory modules that have been tested and qualified for use with this motherboard. Size Vendor Model 256MB A DATA MDGA5F3G315B1EC2 256MB A DATA 256MB A DATA 256MB 512MB Brand ADATA SS/DS Component A* B* C* SS ADD8608A8A-5B • • • MDOWB5F3G316B1EAE Winbond SS W942508BH-5 • • MDOSS6F3G31JB1EAE SAMSUNG SS K4H560838D-TCC4 • • Apacer 77.10636.465 SAMSUNG SS K4H560838D-TCC4 • • • Apacer 77.10736.
2.5.3 Installing a DIMM DIMM_B2 80 Pins DIMM_B1 Follow these steps to install a DIMM. DIMM_A2 DIMM_A1 Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components. 1. Locate the DIMM sockets in the motherboard. 104 Pins ® P4P800 P4P800 184-Pin DDR DIMM Sockets DDR DIMM NOTCH 2. Unlock a DIMM socket by pressing the retaining clips outward. 3.
2.6 Expansion slots In the future, you may need to install expansion cards. The motherboard has five PCI slots and one Accelerated Graphics Port (AGP) slot. The following sub-sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. 2.6.1 Installing an expansion card Follow these steps to install an expansion card. 1.
Standard Interrupt Assignments IRQ 0 1 2 3* 4* 5* 6 7* 8 9* 10* 11* 12* 13 14* 15* * Priority 1 2 N/A 11 12 13 14 15 3 4 5 6 7 8 9 10 Standard Function System Timer Keyboard Controller Programmable Interrupt Communications Port (COM2) Communications Port (COM1) Sound Card (sometimes LPT2) Floppy Disk Controller Printer Port (LPT1) System CMOS/Real Time Clock ACPI Mode when used IRQ Holder for PCI Steering IRQ Holder for PCI Steering PS/2 Compatible Mouse Port Numeric Data Processor Primary IDE Channel Se
2.6.3 PCI slots There are five 32-bit PCI slots on this motherboard. The slots support PCI cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The following figure shows a LAN card installed on a PCI slot. • • • The PCI 5 slot and the WiFi slot can not be used at the same time. When installing long PCI cards, it is recommended that to install in PCI slots 2, 4 or 5. Long PCI cards installed in PCI slot 1 may interfere with the SATA connectors.
2.6.4 AGP slot This motherboard has an Accelerated Graphics Port (AGP) slot that only supports +1.5V AGP cards. When you buy an AGP card, make sure that you ask for one with +1.5V specification. Note the notches on the card golden fingers to ensure that they fit the AGP slot on your motherboard. Install only 1.5V AGP cards on this motherboard! 3.3V AGP cards are not supported in this motherboard. ® P4P800 Keyed for 1.
2.6.5 Wi-Fi slot The Wi-Fi (Wireless Fidelity) slot will support the ASUS Wi-Fi module when available. Visit the ASUS website (www.asus.com) for product updates. The Wi-Fi slot conforms to the Institute of Electrical and Electronics Engineers (IEEE) 802.11b standard for wireless devices operating in the 2.4 GHz frequency band. This standard includes provisions for three radio technologies: direct sequence spread spectrum, frequency hopping spread spectrum, and infrared. Devices that comply with the 802.
2.7 Jumpers 1. Clear RTC RAM (CLRTC1) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The RAM data in CMOS, that include system setup information such as system passwords, is powered by the onboard button cell battery. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the onboard battery. 3.
2. SMB 2.0 (6-1 pin SMB20) This jumper allows you to enable or disable the SM bus support for PCI slots. Set this jumper to pins 1-2 to enable the SM bus support. The jumpers are disable as default setting. SMB20 ® 2 3 1 2 P4P800 Enable Disable (Default) P4P800 SMB2.0 Support 3. Keyboard power (3-pin KBPWR) This jumper allows you to enable or disable the keyboard wake-up feature.
4. USB device wake-up (3-pin USBPW12, USBPW34, USBPW56, USBPW78) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode). The USBPW12 and USBPW34 jumpers are for the rear USB ports.
2.8 Connectors This section describes and illustrates the internal connectors on the motherboard. Always connect ribbon cables with the colored to Pin 1 on the connectors. Pin 1 is usually on the side closest to the power connector on hard drives and CD-ROM drives, but may be on the opposite side on floppy disk drives. 1. Floppy disk drive connector (34-1 pin FLOPPY1) This connector supports the provided floppy drive ribbon cable.
2. IDE connectors (40-1 pin PRI_IDE1, SEC_IDE1) This connector supports the provided UltraDMA100/66 IDE hard disk ribbon cable. Connect the cable’s blue connector to the primary (recommended) or secondary IDE connector, then connect the gray connector to the UltraDMA100/66 slave device (hard disk drive) and the black connector to the UltraDMA100/66 master device. It is recommended that you connect non-UltraDMA100/66 devices to the secondary IDE connector.
3. Serial ATA connectors (7-pin SATA1, SATA2) These next generation connectors support the thin Serial ATA cables for primary internal storage devices. The current Serial ATA interface allows up to 150 MB/s data transfer rate, faster than the standard parallel ATA with 133 MB/s (Ultra ATA/133).
Parallel ATA and Serial ATA device configurations Following are the Parallel ATA and Serial ATA device configurations supported by Intel ICH5 specifications. Native operating systems (OS) are Windows 2000/XP. ICH5R supports a maximum of six (6) devices using these OS. Legacy OS are MS-DOS, Windows 98/Me/NT4.0. ICH5R supports a maximum of four (4) devices using these OS. Operating System Primary (2 devices) P-ATA Secondary S-ATA Port 0 Port 1 (2 devices) (1 device) (1 device) — — 1.
4. RAID ATA/133/100/66/33 connectors (40-1 pin PRI_RAID1, SEC_RAID1) These connectors support either RAID 0, RAID 1, RAID 0 + 1 or JBOD configuration through the onboard VIA® 6410 controller. You can use the RAID feature to set up a disk array configuration and to support additional IDE devices. NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1.
6. Chassis intrusion connector (4-1 pin CHASSIS1) This lead is for a chassis designed with intrusion detection feature. This requires an external detection mechanism such as a chassis intrusion sensor or microswitch. When you remove any chassis component, the sensor triggers and sends a high-level signal to this lead to record a chassis intrusion event. By default, the pins labeled “Chassis Signal” and “Ground” are shorted with a jumper cap.
8. ATX power connectors (20-pin ATXPWR, 4-pin ATX12V) These connectors connect to an ATX 12V power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. In addition to the 20-pin ATXPWR1 connector, this motherboard requires that you connect the 4-pin ATX +12V power plug to provide sufficient power to the CPU. 1. Do not forget to connect the 4-pin ATX +12V power plug.
9. USB headers (10-1 pin USB_56, USB_78) If the USB ports on the rear panel are inadequate, a USB header is available for additional USB ports. The USB header complies with USB 2.0 specification that supports up to 480 Mbps connection speed. This speed advantage over the conventional 12 Mbps on USB 1.1 allows faster Internet connection, interactive gaming, and simultaneous running of high-speed peripherals.
11. GAME/MIDI connector (16-1 pin GAME1) This connector supports an optional GAME/MIDI module. If a GAME/ MIDI module is available, connect the GAME/MIDI cable to this connector. The GAME/MIDI port on the module connects a joystick or a game pad for playing games, and MIDI devices for playing or editing audio files.
13. IEEE 1394 connectors (10-1 pin IEEE1394_2(Orange)) These connectors are for IEEE 1394 modules. Attach the 10-1 pin cable plugs to these connectors. You may also connect a 1394compliant internal hard disk to these connectors. TPA0GND TPB0+12V GND ® 1 P4P800 IEEE-1394 Connector TPA0+ GND TPB0+ +12V IE1394_2 P4P800 NEVER connect a USB cable to any of the IEEE 1394 (orange) connectors. Doing so will damage the motherboard! The IEEE 1394 connector module is not included in this motherboard package.
15. Digital Audio connector (6-1 pin SPDIF_OUT) This connector is for the S/PDIF audio module to allow digital sound output. Connect one end of the S/PDIF audio cable to this connector and the other end to the S/PDIF module. +5V ® SPDIFOUT GND SPDIF_OUT P4P800 P4P800 Digital Audio Connector The S/PDIF module is not included in this motherboard package. 16. Serial Port 2 connector (10-1 pin COM2) This connector accomodates a second serial port using an optional serial port bracket.
17. System panel connector (20-pin PANEL) This connector accommodates several system front panel functions. SMI Lead Reset Ground +5V Ground Ground Speaker PLED- IDE_LED P4P800 ExtSMI# Ground PWR Ground ® IDE_LED+ IDE_LED- PLED+ Power LED Speaker Connector Reset SW ATX Power Switch* * Requires an ATX power supply. P4P800 System Panel Connectors • System Power LED Lead (3-1 pin PLED) This 3-1 pin connector connects to the system power LED.
Chapter 3 This chapter describes the power up sequence and gives information on the BIOS beep codes.
Chapter summary 3.1 Starting up for the first time .......................... 3-1 3.2 Vocal POST Messages ................................... 3-2 3.3 Powering off the computer ...........................
3.1 Starting up for the first time 1. After making all the connections, replace the system case cover. 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: a. Monitor b. External SCSI devices (starting with the last device on the chain) c. System power 6.
3.2 Vocal POST Messages This motherboard includes the Winbond speech controller to support a special feature called the ASUS POST Reporter™. This feature gives you vocal POST messages and alerts to inform you of system events and boot status. In case of a boot failure, you will hear the specific cause of the problem. These POST messages are customizable using the Winbond Voice Editor software that came with your package. You can record your own messages to replace the default messages.
POST Message Action No keyboard detected • Check your keyboard if properly connected to the purple PS/2 connector on the rear panel. • See section “1.4.1 Major components” for the location of the connector. No floppy disk detected • Make sure you have connected a floppy disk to the floppy disk connector on the motherboard. No IDE hard disk detected • Make sure you have connected an IDE hard disk drive to the one of the IDE connectors on the motherboard.
3.3 Powering off the computer Using the OS shut down function If you use Windows 98SE/ME/2000/XP, click the Start button, click Shut Down, then the OK button to shut down the computer. The power supply should turn off after Windows shuts down. Using the dual function power switch While the system is ON, pressing the power switch for less than 4 seconds puts the system to sleep mode or to soft-off mode, depending on the BIOS setting.
Chapter 4 This chapter gives information about the ASUS P4P800 Deluxe Basic Input/Output System (BIOS).This chapter includes updating the BIOS using the AFUDOS.EXE utility that is bundled with the support CD.
Chapter summary 4.1 Managing and updating your BIOS .............. 4-1 4.2 BIOS Setup program ...................................... 4-7 4.3 Main Menu .................................................... 4-10 4.4 Advanced Menu ........................................... 4-15 4.5 Power Menu .................................................. 4-27 4.6 Boot Menu .................................................... 4-32 4.7 Exit Menu ......................................................
4.1 Managing and updating your BIOS • The original BIOS file for this motherboard is in the root directory of the support CD filenamed “P4P800.ROM”. • Copy the original BIOS to a bootable floppy disk in case you need to restore the BIOS in the future. 4.1.1 Creating a bootable floppy disk 1. Do either one of the following to create a bootable floppy disk. DOS environment Insert a 1.44 MB floppy disk into the drive.
4. At the DOS prompt, type the command line: afudos /i where “filename” means the latest (or original) BIOS file that you copied to the bootable floppy disk. The screen displays the status of the update process. The BIOS information on the screen is for reference only. What you see on your screen may not be exactly the same as shown. A:\>afudos /iP4P800.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading file .....
4.1.3 Using AFUDOS to copy BIOS from PC The AFUDOS.EXE utility can also be used to copy the current system BIOS settings to a floppy or hard disk. The copy can be used as a backup in case the system BIOS fails or gets corrupted. 1. At the DOS prompt, type the command line: afudos /o where “filename” can be any user provided filename of not more than eight (8) alpha-numeric characters for the main filename and three (3) alpha-numeric characters for the extension name. Press the Enter key.
4.1.4 Using ASUS EZ Flash to update the BIOS The ASUS EZ Flash feature allows you to easily update the BIOS without having to go through the long process of booting from a diskette and using a DOS-based utility. The EZ Flash is built-in the BIOS firmware so it is accessible by simply pressing + during the Power-On Self Tests (POST). To update the BIOS using ASUS EZ Flash: 1. Visit the ASUS website (www.asus.
4.1.5 Recovering the BIOS with CrashFree BIOS 2 The CrashFree BIOS 2 auto recovery tool allows you to restore BIOS from the motherboard support CD, or from a floppy disk that contains the BIOS file, in case the current BIOS on the motherboard fails or gets corrupted. 1. Prepare the support CD that came with the motherboard or a floppy disk that contains the motherboard BIOS before proceeding with the BIOS update process. 2.
To recover the BIOS from the support CD: 1. Boot the system. 2. When a corrupted BIOS is detected, the following screen message appears. Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... If there is no floppy disk found in the drive, the system automatically checks the CD-ROM. 3. Place the support CD in the CD-ROM. The support CD contains the original BIOS for this motherboard. Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Floppy not found! Checking for CD-ROM...
4.2 BIOS Setup program This motherboard supports a programmable firmware hub (FWH) that you can update using the provided utility described in section “4.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you may want to change the configuration of your computer in the future.
4.2.1 BIOS menu screen Menu items Menu bar System Time System Date Legacy Diskette A Language Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Fourth IDE Master IDE Configuration Configuration fields [11:10:19] [Thu 03/27/2003] [1.44M, 3.5 in] [English] :[ST320413A] :[ASUS CD-S340] :[Not Detected] :[Not Detected] :[Not Detected] :[Not Detected] System Information Sub-menu items General help Use [ENTER], [TAB] or [SHIFT-TAB] to select a field.
4.2.4 Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting Main shows the Main menu items. The other items (Advanced, Power, Boot, and Exit) on the menu bar have their respective menu items. System Time System Date Legacy Diskette A Language Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Fourth IDE Master IDE Configuration [11:10:19] [Thu 03/27/2003] [1.44M, 3.
4.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears giving you an overview of the basic system information. Refer to section “4.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them. System Time System Date Legacy Diskette A Language Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Fourth IDE Master IDE Configuration [11:10:19] [Thu 03/27/2003] [1.44M, 3.
4.3.5 Primary and Secondary IDE Master/Slave; Third and Fourth IDE Master While entering Setup, BIOS auto-detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press Enter to display the IDE device information. Primary IDE Master Select the type of device connected to the system. Device : Hard Disk Vendor : ST320413A Size : 20.
PIO Mode [Auto] Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] Selects the DMA mode. Configuration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] SMART Monitoring [Auto] Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled] 32Bit Data Transfer [Disabled] Enables or disables 32-bit data transfer.
Refer to the section “Parallel ATA and Serial ATA device configurations” on page 2-26 for the appropriate settings of the IDE Configuration items under different operating systems. Enhanced Mode Support On [S-ATA] The default setting S-ATA allows you to use native OS on Serial ATA and Parallel ATA ports. We recommend that you do not change the default setting for better OS compatibility. In this setting, you may use legacy OS on the Parallel ATA ports only if you did not install any Serial ATA device.
4.3.7 System Information This menu gives you an overview of the general system specifications. The items in this menu are auto-detected by BIOS. AMI BIOS Version : 08.00.08 Build Date : 04/03/03 ID : P4P81035 Processor Type Speed Count : Intel(R) Pentium(R) 4 CPU 1.73GHz : 1733 MHz : 1 System Memory Size : 256MB +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit AMI BIOS This item displays the auto-detected BIOS information.
4.4 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Take caution when changing the settings of the Advanced menu items. Incorrect field values may cause the system to malfunction. JumperFree Configuration CPU Configuration Chipset Onboard Devices Configuration PCI PnP USB Configuration Speech Configuration Instant Music Configuration Configure CPU. Select Screen Select Item Enter Go to Sub-screen F1 General Help F10 Save and Exit ESC Exit 4.
If you are using an unlocked CPU, the item CPU Ratio appears under the AI Overclock Tuner item. You may select your desired ratio from the available options. CPU Ratio [12] This field sets the ratio between the CPU Core Clock and the Front Side Bus (FSB) Frequency. If an invalid ratio is set in CMOS, the actual and setpoint values may differ. Performance Mode [Auto] Allows enhanced system performance. Setting to [Turbo] may cause the system to become unstable.
DRAM Frequency [Auto] Allows you to set the DDR operating frequency. Configuration options: [266 MHz] [333 MHz] [400 MHz] [Auto] AGP/PCI Frequency (MHz) [Auto] Allows you to adjust to a higher AGP/PCI frequency for better system performance and overclocking capability. Configuration options: [Auto] [66.66/33.33] [72.73/36.36] [80.00/40.00] Selecting a very high AGP/PCI frequency may cause the system to become unstable! If this happens, revert to the default setting.
4.4.2 CPU Configuration The items in this menu show the CPU-related information auto-detected by BIOS. Configure advanced CPU settings Manufacturer Brand String Frequency : Intel(R) : Intel(R) Pentium(R) 4 CPU 1.
Configure DRAM Timing by SPD [Enabled] When this item is enabled, the DRAM timing parameters are set according to the DRAM SPD (Serial Presence Detect). When disabled, you can manually set the DRAM timing parameters through the DRAM sub-items. Configuration options: [Disabled] [Enabled] Memory Acceleration Mode [Auto] This field when [Enabled] minimize latencies from CPU to memory to boost system performance.
Graphic Adapter Priority [AGP/PCI] Allows selection of the graphics controller to use as primary boot device. Configuration options: [AGP/PCI] [PCI/AGP] Graphics Aperture Size [64MB] Allows you to select the size of mapped memory for AGP graphic data. Configuration options: [4MB] [8MB] [16MB] [32MB] [64MB] [128MB] [256MB] Spread Spectrum [Enabled] This field enables or disables the clock generator spread spectrum.
OnBoard VT6410 RAID Controller [Enabled] Allows you to enable or disable the onboard VIA® VT6410 RAID controller. Configuration options: [Disabled] [Enabled] OnBoard IEEE 1394 Controller [Enabled] Allows you to enable or disable the onboard IEEE 1394 controller. Configuration options: [Disabled] [Enabled] OnBoard LAN [Enabled] Allows you to enable or disable the onboard LAN controller.
Parallel Port IRQ [IRQ7] Configuration options: [IRQ5] [IRQ7] Onboard Game/MIDI Port [Disabled] Allows you to select the Game Port address or to disable the port. Configuration options: [Disabled] [200/300] [200/330] [208/300] [208/330] 4.4.5 PCI PnP The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices.
Allocate IRQ to PCI VGA [Yes] When set to [Yes], BIOS assigns an IRQ to PCI VGA card if the card requests for an IRQ. When set to [No], BIOS does not assign an IRQ to the PCI VGA card even if requested. Configuration options: [No] [Yes] Pallete Snooping [Disabled] When set to [Enabled], the pallete snooping feature informs the PCI devices that an ISA graphics device is installed in the system so that the latter can function correctly. Setting to [Disabled] deactivates this feature.
USB Function [8 USB Ports] Allows you to set the number of USB ports to activate. Configuration options: [Disabled] [2 USB Ports] [4 USB Ports] [6 USB Ports] [8 USB Ports] Legacy USB Support [Auto] Allows you to enable or disable support for legacy USB devices. Setting to Auto allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled.
Emulation Type [N/A] When set to Auto, USB devices less than 530MB will be emulated as floppy drive, and the remaining drives as hard drives. Forced FDD option can be used to force an HDD formatted drive to boot as FDD (for example, ZIP drive). The Device and Emulation Type items appear only when there are installed USB devices. 4.4.7 Speech Configuration - Speech Option Speech Post Reporter Report IDE Error Report System Booting Disable/Enable Speech.
4.4.8 Instant Music Configuration Instant Music Option Instant Music [Disabled] Disable/Enable Instant Music feature. +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit Instant Music [Disabled] Allows you to enable or disable the Instant Music feature in BIOS. Configuration options: [Disabled] [Enabled] When Instant Music is enabled, the PS/2 keyboard power up feature is automatically disabled. See page 5-14 for details.
4.5 Power menu The Power menu items allow you to change the settings for the Advanced Power Management (APM). Select an item then press Enter to display the configuration options. Suspend Mode Repost Video on S3 Resume ACPI 2.0 Support ACPI APIC Support BIOS -> AML ACPI table [Auto] [No] [No] [Enabled] [Enabled] Configure CPU. APM Configuration Hardware Monitor Select Screen Select Item Enter Go to Sub-screen F1 General Help F10 Save and Exit ESC Exit 4.5.
4.5.6 APM Configuration APM Configuration Power Management/APM Video Power Down Mode Hard Disk Power Down Mode Suspend Time Out Throttle Slow Clock Ratio [Enabled] [Suspend] [Suspend] [Disabled] [50%] System Thermal [Disabled] Power Button Mode Restore on AC Power Loss [On/Off] [Power Off] Power Power Power Power Power [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] On On On On On By By By By By RTC Alarm External Modem PCI Devices PS/2 Keyboard PS/2 Mouse Enabled or disable APM.
Power Button Mode [On/Off] Allows the system to go into On/Off mode or suspend mode when the power button is pressed. Configuration options: [On/Off] [Suspend] Restore on AC Power Loss [Power Off] When set to Power Off, the system goes into off state after an AC power loss. When set to Power On, the system goes on after an AC power loss. When set to Last State, the system goes into either off or on state whatever was the system state before the AC power loss.
Power On By PS/2 Mouse [Disabled] When set to [Enabled], this parameter allows you to use the PS/2 mouse to turn on the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Enabled] 4.5.7 Hardware Monitor Hardware Monitor CPU temperature CPU Temperature MB Temperature Power Temperature [44°C/111°F] [36°C/96.
Fan Speed Ratio [11/16] This item allows you to select the appropriate fan speed ratio for the system. The default [11/16] is the minimum fan speed ratio. Select a higher ratio if you installed additional devices and the system requires more ventilation. Configuration options: [11/16] [12/16] [13/16] [14/16] [15/16] The above item appears only when the Q-Fan Control item is set to Enabled.
4.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press Enter to display the sub-menu. Boot Settings Specifies the Boot Device Priority sequence. Boot Device Priority Hard Disk Drives Boot Settings Configuration Security Select Screen Select Item Enter Go to Sub-screen F1 General Help F10 Save and Exit ESC Exit 4.6.
4.6.2 Hard disk drives Boot Device Priority 1st Boot Device 2nd Boot Device [PM-ST320413A] [PS-ASUS CD-S340] Specifies the boot sequence from the available devices. A device enclosed in parenthesis has been disabled in the corresponding type menu. +F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit 1st ~ xxth Boot Device [(Hard disk drive model name)] These items specify the boot device priority sequence from the available hard disk drives.
Full Screen Logo [Enabled] This allows you to enable or disable the full screen logo display feature. Configuration options: [Disabled] [Enabled] Make sure that the above item is set to [Enabled] if you wish to use the ASUS MyLogo2™ feature. Add On ROM Display Mode [Force BIOS] Sets the display mode for option ROM. Configuration options: [Force BIOS] [Keep Current] Bootup Num-Lock [On] Allows you to select the power-on state for the NumLock.
4.6.4 Security The Security menu items allow you to change the system security settings. Select an item then press Enter to display the configuration options. Security Settings Supervisor Password User Password Not Installed Not Installed to change password. again to disable password.
After you have set a supervisor password, the other items appear to allow you to change other security settings. Security Settings Supervisor Password User Password Change Supervisor Password User Access Level Change User Password Clear User Password Password Check Boot Sector Virus Protection to change password. again to disable password.
To change the user password, follow the same steps as in setting a user password. Clear User Password Select this item if you wish to clear the user password. Password Check [Setup] When set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system.
Exit & Save Changes Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM. The CMOS RAM is sustained by an onboard backup battery and stays on even when the PC is turned off. When you select this option, a confirmation window appears. Select [Yes] to save changes and exit.
Chapter 5 This chapter describes the contents of the support CD that comes with the motherboard package.
Chapter summary 5.1 Install an operating system ........................... 5-1 5.2 Support CD information ................................ 5-1 5.3 Software information ..................................... 5-7 5.4 RAID 0/ RAID 1 / RAID 0+1 / JBOD ..................... configurations .............................................. 5-25 5.5 Intel® RAID for Serial ATA configuration .... 5-34 5.6 Using Intel® / VIA® Makedisk.exe ................ 5-38 5.7 Marvell® Virtual Cable Tester™ (VCT) .......
5.1 Install an operating system This motherboard supports Windows 98SE/ME/2000/XP operating system (OS). Always install the latest OS version and corresponding updates so you can maximize the features of your hardware. Because motherboard settings and hardware options vary, use the setup procedures presented in this chapter for general reference only. Refer to your OS documentation for more information. 5.
5.2.2 Drivers menu The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. Intel Chipset Inf Update Program This item installs the Intel® Chipset INF Update Program that enables Plug-n-Play INF support for Intel® chipset components. This utility installs to the target system the Windows INF files that outline to the operating system how the chipset components will be configured.
USB 2.0 Driver This item installs the Universal Serial Bus 2.0 driver. 3Com Gigabit LOM (3C940) Driver This item executes the dialogue box interface for the 3COM NIC driver and diagnostics installation. Screen display and driver options may not be the same for other operating system versions. 5.2.3 Utilities menu The Utilities menu shows the applications and other software that the motherboard supports.
PC-CILLIN 2002 This item installs the PC-cillin 2002 anti-virus program. View the PC-cillin online help for detailed information. Adobe Acrobat Reader V5.0 This item installs the Adobe Acrobat Reader V5.0. The Acrobat Reader software is for viewing files saved in Portable Document Format (PDF). Winbond Voice Editor This item installs the Winbond Voice Editor software application. ASUS Screen Saver This item installs the ASUS screen saver. E-Color 3Deep This item installs the 3Deep software.
5.2.5 Other information The icons on the top right corner of the screen give additional information on the motherboard and the contents of the support CD. Click an icon to display the specified information. Motherboard Info The window displays the general specifications of the P4P800 Deluxe motherboard. Browse this CD The window displays the support CD contents in graphical format.
Technical Support Form The window displays the ASUS Technical Support Request Form that you have to fill up when requesting technical support. Filelist The window displays the contents of the support CD and a brief description of each in text format.
5.3 Software information Most of the applications in the support CD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software for more information. This section provides details on the software applications that the motherboard supports. 5.3.1 ASUS Update The ASUS Update is a utility that allows you to update the motherboard BIOS and drivers.
4. From the FTP site, select the BIOS version that you wish to download. Click Next. 5. Follow the instructions on the succeeding screens to complete the update process. If you selected the option to update the BIOS from a file, a window pops up prompting you to locate the file. Select the file, click Save, then follow the screen instructions to complete the update process. 5.3.2 ASUS MyLogo2™ The ASUS MyLogo2™ is automatically installed when you install the ASUS Update utility from the software menu.
4. From the selection that appears, choose a logo image. Click Next. If you wish, you may create your own boot logo image in GIF, JPG, or BMP file formats. 5. When you click on an image, it displays larger on the MyLogo2 screen. If you wish to make the logo image smaller, click on the arrow on the Ratio item and select your desired scale. 6. The next screen prompts you to flash the original BIOS to update it with the new boot logo. Click Flash to update the BIOS. 7.
5.3.3 ASUS PC Probe The ASUS PC Probe is a convenient utility to continuously monitor your computer system’s vital components, such as fan rotations, voltages, and temperatures. It also has the DMI Explorer utility that lets you review useful information about your computer, such as hard disk space, memory usage, and CPU type, CPU speed, and internal/external frequencies.
Using ASUS PC Probe Monitoring Monitor Summary Shows a summary of the items being monitored. Temperature Monitor Shows the PC temperature (for supported processors only). Temperature Warning threshold adjustment (Move the slider up to increase the threshold level or down to decrease the threshold level) Fan Monitor Shows the PC fan rotation.
Settings Lets you set threshold levels and polling intervals or refresh times of the PC’s temperature, fan rotation, and voltages. CPU Cooling System Setup Lets you select when to enable software CPU cooling. When When CPU Overheated is selected, the CPU cooling system is enabled whenever the CPU temperature reaches the threshold value. History Lets you record the monitoring activity of a certain component of your PC for future reference. Fan Control Lets you enable/disable Smart Fan Control.
Information Memory Shows the PC memory load, memory usage, and paging file usage. Device Summary Shows a summary of devices present in your PC. DMI Explorer Shows information pertinent to the PC, such as CPU type, CPU speed, and internal/external frequencies, and memory size. Utility Lets you run programs outside of the ASUS Probe modules. To run a program, click Execute Program. NOTE: This feature is currently unavailable.
ASUS PC Probe Task Bar Icon Right clicking the PC Probe icon brings up a menu to open or exit ASUS PC Probe and pause or resume all system monitoring. When the ASUS PC Probe senses a problem with your PC, portions of the ASUS PC Probe icon change to red, the PC speaker beeps, and the ASUS PC Probe monitor appears. 5.3.4 ASUS Instant Music The ASUS Instant Music is a BIOS-based audio playback feature that allows you to play audio CDs without booting the system.
4. Highlight the Instant Music CDROM item and press Enter to display the CD-ROM options. Select the CD-ROM drive that you wish to use for this feature. 5. Save your changes and exit BIOS Setup. 1. The Scroll Lock LED is fixed to ON after enabling Instant Music. 2. When set to Instant Music mode, the system wake-up features (LAN, keyboard, mouse, USB) are deactivated. In this case, power up the system using the power switch. 3.
These labels all come with your motherboard package. 3. Connect speakers or a headphone to the Line Out (lime colored) port on the rear panel for audio output. You may also connect a headphone to the headphone jack on the CDROM drive front panel. 4. Place an audio CD on the drive. 5. Press Esc to turn ON Instant Music. 6. Press F1 or the Space Bar to play the first track on the CD. If there is no CD on the drive and you press F1 or Space Bar, the drive tray ejects. 7.
5.3.5 Winbond Voice Editor The Winbond Voice Editor software allows you to customize the vocal POST messages. Install the software from the software menu in the support CD. See section “5.2.3 Utilities menu”. To avoid conflicts, do not run the Winbond Voice Editor while running the ASUS PC Probe. Follow these steps to use the Winbond Voice Editor.
Changing the default language 1. Click on the Load button. a window showing the available languages appears. 2. Select your desired language then click Open. The event messages for the language you selected appear on the Voice Editor screen. For some languages, not all events have a corresponding message due to file size constraints. 3. Click on the Write button to update the EEPROM. 4. Click Yes on the confirmation window that appears.
Customizing your POST messages If your language is not in the selection or if you wish to record your own POST messages to replace the pre-installed wave files, you may easily do so. Follow these steps to customize your POST messages. 1. Launch the Voice Editor and take note of the list of POST events on the leftmost column of the screen. 2. Prepare your message for each event. The total compressed size for all the wave files must not exceed 1Mbit, so make your messages as short as possible. 3.
7. Click a POST event on the Voice Editor screen, then on the Edit button. The Event Sound Editor window appears. 8. Locate and select your wave file for the event then click on the arrow opposite Voice1. The file you selected appears on the space next to it. 9. Click OK to return to the Voice Editor screen. 10. Do steps 7 to 9 for the other events. 11. When done, click the Save button. A window appears prompting you to save your configuration. 12. Type a file name with a .flh extension, then click Save.
5.3.6 SoundMAX® 4 XL software The ADI AD1985 AC ‘97 audio CODEC provides 6-channel audio capability through the SoundMAX4 XL with AudioESP™ software to deliver the ultimate audio experience on your PC. The software implements high quality audio synthesis/rendering, 3D sound positioning, and advanced voice-input technologies. Follow the installation wizard install the SoundMAX Audio Driver and Application from the support CD that came with the motherboard package to activate the 6-channel audio feature.
Setup wizards Use the speaker and microphone setup wizards to fine tune the gain/ attenuation of the inputs/outputs for optimal audio performance. You may launch the setup wizards by clicking the Configuration button when AudioESP detects and verifies a newly connected peripheral, or by clicking icon from the SoundMAX control panel. on the Speaker wizard Follow the screen instructions to configure the speakers to your desired settings.
Audio preferences The Preferences page of the SoundMAX4 XL allows you to change various audio settings. Listening environment options The SoundMAX4 XL support several audio technologies including SoundMAX SPX™ Animated Audio, 3DPA™, MultiDrive™ 5.1, EnvironmentFC™, MacroFX/ZoomFX™, and Virtual Theater Surround.
Rear panel audio ports function variation The functions of the Line Out (lime), Line In (blue), and Mic (pink) ports on the rear panel change when you select the 4-channel or 6-channel audio configuration as shown in the following table.
5.4 RAID 0 / RAID 1 / RAID 0+1 / JBOD configurations The motherboard includes VIA® VT6410 high performance IDE RAID controller. It supports RAID 0, RAID 1, RAID 0+1 and JBOD with two independent IDE channels. This controller also complies with Scatter/ Gather host DMA mechanism of Programming Interface for Bus Master IDE Controller Revision 1.0 and builts 64 levels of pre-fetch and write buffer inside to improve the transfer rate.
5.4.1 Install the hard disks The VIA® VT6410 chipset supports UltraDMA133/100/66 hard disk drives. For optimal performance, install identical drives of the same model and capacity when creating a RAID set. • If you are creating a RAID 0 (striping) array for perfomance, use two new drives. • If you are creating a RAID 1 (mirroring) array for protection, you can use two new drives or use an existing drive and a new drive (the new drive must be of the same size or larger than the existing drive).
4. Connect the power cable to the power connector on each drive. 5. Proceed to section 5.4.2 for the next procedure. 5.4.2 Entering VIA® Tech RAID BIOS Utility 1. Boot-up your computer. 2. During POST, press to enter VIA RAID configuration utility. The following menu options will appear. The RAID BIOS information on the setup screen shown is for reference only. What you see on your screen may not be exactly the same as shown. VIA Tech. RAID BIOS Ver 1.
5.4.3 Create Array 1. In the VIA RAID BIOS utility main menu, select Create Array then press the key. The main menu items on the upper-left corner of the screen are replaced with create array menu options. VIA Tech. RAID BIOS Ver 1.
TIP: For server systems, it is recommended to use a lower array block size. For multimedia computer systems used mainly for audio and video editing, a higher array block size is recommended for optimum performance 4K 8K 16K 32K 64K Use arrow keys to move selection bar on items and press to select. 5. Select Start Create Process and press to setup hard disk for RAID system.
4. Select Select Disk Drives, then press . Use arrow keys to select disk drive/s, then press to mark selected drive. (An asterisk is placed before a selected drive.) 5. Select Start Create Process and press to setup hard disk for RAID system. The following confirmation message appears: The same confirmation message appears when the Auto Setup for Data Security option is selected. The data on the selected disks will be destroyed.
5. Select Block Size, then press to set array block size. A list of valid array block sizes are displayed on a pop-up menu. TIP: For server systems, it is recommended to use a lower array block size. For multimedia computer systems used mainly for audio and video editing, a higher array block size is recommended for optimum performance 4K 8K 16K 32K 64K Use arrow keys to move selection bar on items and press to select. 6.
4. Select Start Create Process and press to setup hard disk for RAID system. The following confirmation message appears: The same confirmation message appears when the Auto Setup for Capacity option is selected. The data on the selected disks will be destroyed. Continue? Press Y/N Press “Y” to confirm or “N” to return to the configuration options. 5.4.4 Delete Array 1. In the VIA RAID BIOS utility main menu, select Delete Array then press the key.
5.4.6 Select Boot Array 1. In the VIA RAID BIOS utility main menu, select Select Boot Array then press the key. The focus is directed to the list of channel used for IDE RAID arrays. 2. Press the key to select a RAID array for boot. The Status of the selected array will change to Boot. Press key to go return to menu items. Follow the same procedure to deselect the the boot array.
5.5 Intel® RAID for Serial ATA configuration This motherboard supports Intel® RAID 0 for Serial ATA drives through the Intel® ICH5R chipset. The Serial ATA as RAID option must be enabled in the BIOS before the system can load the Intel® RAID Option ROM code for Intel® RAID. The Intel® RAID Option ROM is a standard PnP (Plug and Play) option ROM that provides a pre-operating system user interface for the Intel® RAID implementation.
5.5.3 Creating, Deleting, and Resetting RAID Sets The Serial ATA RAID set must be configured in the RAID Configuration utility. This configuration can be done by the Intel® RAID Option ROM. During the Power-On Self Test (POST), the following message will appear for a few seconds: Press to enter Raid Configuration Utility. After this message appears, press the and keys simultaneously, the following screen menu appears.
2. Select the stripe value for the RAID 0 array by scrolling through the available values by using the Up and Down arrow keys and pressing the key. 3. The available values range from 8 KB to 128 KB increments. The strip value should be chosen based on the planned drive usage. Some suggested selections are listed below. The default selection is 64 KB. • 16 KB - low disk usage • 64 KB - typical disk usage • 128 KB - performance disk usage 4.
1. Select option 2 Delete RAID Volume and press the key to delete the RAID set. 2. Press the key to delete the RAID volume. [ VOLUME DELETE VERIFICATION ] Are you sure you want to delete this volume? ALL DATA IN THE VOLUME WILL BE LOST!! Are you sure you want to delete volume "RAID_Volume1"? (Y/N) 3. Confirm the volume deletion by pressing the key. 5.5.6 Reset RAID Data Intel(R) Integrated RAID for Serial ATA - RAID Configuration Utility Copyright(C) 2003 Intel Corporation.
5.6 Using Intel® / VIA® Makedisk.exe Important Notes 1. The Makedisk.exe utility enables you to create a floppy disk with the RAID driver necessary when configuring RAID installations. 2. The Makedisk.exe utility for Intel® RAID is located in “/Drivers/chipset/IAA/Makedisk.exe” of the support CD. The Makedisk.exe utility for Intel® RAID is supported in Windows® XP™ only. 3. The Makedisk.exe utility for VIA® RAID is located in “/Drivers/VIARAID/Makedisk.exe” of the support CD.
5.7 Marvell® Virtual Cable Tester™ (VCT) Technology The P4P800 Deluxe motherboard supports the Marvell® Virtual Cable Tester (VCT) Technology. The VCT virtually diagnose and report cable faults using the Time Domain Reflectometry (TDR). With this essential tool, installation and network diagnosis have never been easier. The VCT technology detects and reports open and shorted cables with up to 1 meter of accuracy.
4. Click on the (VCT) Virtual Cable Tester button. The following screen display appears. 5. Click on Run to execute test. 5-40 • The Virtual Cable Tester™ (VCT) feature is supported in Windows® XP™ and Windows® 2000™ operating systems only. • The Run button on the VCT Tester dialogue box is disabled if no problem is detected on the network.
