User Guide Motherboard P4P800-X
E1718 Checklist First Edition July 2004 Copyright © 2003 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Features Notices ........................................................................................... vi Safety information ......................................................................... vii About this guide ............................................................................ viii Conventions used in this guide ........................................... viii Where to find more information ........................................... viii P4P800-X specification summary ...
Contents Safeguards Chapter 2: BIOS Information 2.1 2.2 2.3 2.4 2.5 iv Managing and updating your BIOS .................................... 2-2 2.1.1 Creating a bootable floppy disk ............................. 2-2 2.1.2 Using AFUDOS to copy the current BIOS ............. 2-3 2.1.3 Using AFUDOS to update the BIOS ...................... 2-3 2.1.4 Using ASUS EZ Flash to update the BIOS ............ 2-5 2.1.5 Recovering the BIOS with CrashFree BIOS 2 ....... 2-6 BIOS Setup program .....................
Contents 2.6 2.7 2.5.5 BIOS -> AML ACPI Table ..................................... 2-24 2.5.6 APM Configuration ............................................... 2-25 2.5.7 Hardware Monitor ................................................ 2-27 Boot menu ........................................................................ 2-28 2.6.1 Boot Device Priority ............................................. 2-28 2.6.2 Boot Settings Configuration ................................. 2-28 2.6.3 Security ............
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Information that you MUST follow to complete a task. NOTE: Tips and additional information to aid in completing a task.
P4P800-X specification summary CPU Socket 478 for Intel® Pentium® 4 / Celeron® processors Supports Intel® Hyper-Threading technology Chipset Intel® 865PE Intel® ICH5 Front Side Bus (FSB) 800/533/400 MHz Memory Dual-channel memory architecture 4 x 184-pin DDR DIMM sockets for up to 4GB memory Supports PC3200/PC2700/PC2100 unbuffered non-ECC DDR DIMMs Supports ASUS Hyper-Path Technology Expansion slots 1 x AGP 8X/4X (0.8 V or 1.
P4P800-X specification summary Internal I/O 2 x USB 2.0 connector for 4 additional USB ports CPU/Chassis fan connectors 20-pin/4-pin ATX 12V power connectors CD/AUX connectors Game/MIDI port connector 20-pin panel connector Front panel audio connector Chassis intrusion connector Serial 2 (COM2) connector S/PDIF out connector BIOS features 3Mb Flash ROM, AMI BIOS, ACPI, PnP, DMI2.0, WfM 2.0, SM BIOS 2.3 Industry standard PCI 2.3, USB 2.0/1.1 Manageability DMI 2.
Chapter 1 This chapter describes the features of the P4P800-X motherboard. It includes brief descriptions of the motherboard components, and illustrations of the layout, jumper settings, and connectors.
1.1 Welcome! Thank you for buying the ASUS® P4P800-X motherboard! The ASUS P4P800-X motherboard, based on the Intel® 865PE chipset supporting 800FSB that delivers a host of new features and latest technologies making it another standout in the long line of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your P4P800-X package for the following items.
Serial ATA solution The motherboard supports two interfaces compliant to the Serial ATA (SATA) specification, an evolutionary replacement of the Parallel ATA storage interface. The Serial ATA specification allows for thinner, more flexible cables with lower pin count, reduced voltage requirement, up to 150 MB/s data transfer rate, and software compatibility with legacy Parallel ATA. See page 1-21.
1.4 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. 1. 2. 3. 4. 5. Unplug the power cord from the wall socket before touching any component. Use a grounded wrist strap or touch a safely grounded object or to a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity. Hold components by the edges to avoid touching the ICs on them.
1.5 Motherboard overview 1.5.1 Motherboard layout 20.8cm (8.2in) PS/2KBMS T: Mouse B: Keyboard ATX Power Connector CPU_FAN Top:Line In Center:Line Out Below:Mic In Intel 865PE MCH CD AD1888 PRI_IDE Accelerated Graphics Port (AGP) CLRTC CHASSIS FP_AUDIO SPDIF_OUT AUX 30.5cm (12.
1.5.2 Placement direction When installing the motherboard, make sure that you place it into the chassis in the correct orientation. The edge with external ports goes to the rear part of the chassis as indicated in the image below. 1.5.3 Screw holes Place seven (7) screws into the holes indicated by circles to secure the motherboard to the chassis. Do not overtighten the screws! Doing so may damage the motherboard.
1.6 Central Processing Unit (CPU) 1.6.1 Overview The Intel® Pentium® 4 Northwood/Prescott processors has a gold triangular mark on one corner. This mark indicates the processor Pin 1 that should match a specific corner of the CPU socket.
1.6.2 Installing the CPU Follow these steps to install a CPU. 1. Locate the 478-pin ZIF socket on the motherboard. 2. Unlock the socket by pressing the lever sideways, then lift it up to a 90°100° angle. Socket Lever 90 - 100 Make sure that the socket lever is lifted up to 90°-100° angle, otherwise the CPU does not fit in completely. 3. Position the CPU above the socket such that its marked corner matches the base of the socket lever. Gold Mark 4.
1.7 System memory 1.7.1 DIMM sockets location 104 Pins 80 Pins The following figure illustrates the location of the DDR DIMM sockets. P4P800-X DIMM_B1 DIMM_B2 DIMM_A1 P4P800-X 184-Pin DDR DIMM sockets DIMM_A2 ® Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components. 1.7.
Table 1 Recommended memory configurations Sockets Mode Single-channel Dual-channel DIMM_A1 (blue) DIMM_A2 (black) DIMM_B1 (blue) DIMM_B2 (black) (1) Populated — — — (2) — Populated — — (3) — — Populated — (4) — — — Populated (1) Populated — Populated — (2) — Populated — Populated Populated Populated Populated (3) *Populated * For dual-channel configuration (3), you may: • install identical DIMMs in all four sockets • install identical DIMM pair in DIMM_A1 and DIM
DDR400 Qualified Vendor List (QVL) DIMM support Size Vendor Model Brand Side(s) Component A B C 256MB BRAIN POWER 512MB BRAIN POWER 256MB CENTURY B6U808-256M-SAM-400 B6U808-512M-SAM-400 DXV6S8MC5BC3U27E SAMSUNG SAMSUNG MICRON SS DS SS K4H560838D-TCC4 K4H560838D-TCC4 MT46V32M8TG-5BC • • • • • • • • • 256MB 256MB 512MB 512MB 512MB 256MB 256MB 256MB 512MB 512MB 512MB CENTURY CENTURY CENTURY CENTURY CENTURY CORSAIR CORSAIR CORSAIR CORSAIR CORSAIR CORSAIR DXV6S8SSCCD3K27C DXV6S8SSCCE3K27E DXV
1.7.3 Installing a DIMM DDR DIMM Follow these steps to install a DIMM. 1. Unlock a DIMM socket by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. 3. Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated. Unlocked A DDR DIMM is keyed with a notch so that it fits in only one direction. DO NOT force a DIMM into a socket to avoid damaging the DIMM.
1.8 Expansion slots To install and configure an expansion card: 1. Install an expansion card following the instructions that came with the chassis. 2. Turn on the system and change the necessary BIOS settings, if any. See Chapter 2 for BIOS information. 3. Assign an IRQ to the card. Refer to the tables next page. 4. Install the drivers and/or software applications for the expansion card according to the card documentation. 1.8.
1.8.3 PCI slots The PCI slots support PCI cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. 1.8.4 AGP slot The Accelerated Graphics Port (AGP) slot that supports AGP 8X/4X (+1.5V) cards. When you buy an AGP card, make sure that you ask for one with +1.5V specification. Note the notches on the card golden fingers to ensure that they fit the AGP slot on the motherboard. This motherboard does not support 3.3V AGP cards. Install only +1.5V or 0.
1.9 Jumpers 1. Clear RTC RAM (CLRTC1) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The RAM data in CMOS, that include system setup information such as system passwords, is powered by the onboard button cell battery. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Move the jumper cap from pins 1-2 (default) to pins 2-3.
2. USB device wake-up (3-pin USBPW12, USBPW34, USBPW56, USBPW78) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode). The USBPWR12 and USBPWR34 jumpers are for the rear USB ports.
1.10 Connectors This section describes and illustrates the motherboard rear panel and internal connectors. 1.10.1 Rear panel connectors 1 2 3 4 5 6 11 10 9 8 7 1. PS/2 mouse port. This port is for a PS/2 mouse. 2. Parallel port. This 25-pin port connects a parallel printer, a scanner, or other devices. 3. RJ-45 port. This port allows connection to a Local Area Network (LAN) through a network hub. 4. Line In jack. This Line In (light blue) jack connects a tape player or other audio sources.
1.10.2 Internal connectors 1. Floppy disk drive connector (34-1 pin FLOPPY) This connector supports the provided floppy drive ribbon cable. After connecting one end to the motherboard, connect the other end to the floppy drive. (Pin 5 is removed to prevent incorrect insertion when using ribbon cables with pin 5 plug). FLOPPY PIN 1 P4P800-X NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. ® P4P800-X Floppy disk drive connector 2.
3. Serial ATA connectors (7-pin SATA1, SATA2) These next generation connectors support the thin Serial ATA cables for primary internal storage devices. The current Serial ATA interface allows up to 150 MB/s data transfer rate, faster than the standard parallel ATA with 133 MB/s (Ultra ATA/133).
Parallel ATA and Serial ATA device configurations Following are the Parallel ATA and Serial ATA device configurations supported by Intel ICH5 specifications. Native operating systems (OS) are Windows 2000/XP. ICH5 supports a maximum of six (6) devices using these OS. Legacy OS are MS-DOS, Windows 98/ME. ICH5 supports a maximum of four (4) devices using these OS. Operating System Primary (2 devices) P-ATA Secondary S-ATA Port 0 Port 1 (2 devices) (1 device) (1 device) — — 1. Windows 2000/XP 2.
4. ATX power connectors (20-pin ATXPWR, 4-pin ATX12V) These connectors connect to an ATX 12V power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. In addition to the 20-pin ATX power connector, this motherboard requires that you connect the 4-pin ATX +12V power plug to provide sufficient power to the CPU.
6. CPU and chassis fan connectors (3-pin CPU_FAN, CHA_FAN) The fan connectors support cooling fans of 350mA~740mA (8.88W max.) or a total of 1A~2.22A (26.64W max.) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Lack of sufficient air flow within the system may damage the motherboard components.
8. Front panel audio connector (10-1 pin FP_AUDIO) This is an interface for the front panel cable that allows convenient connection and control of audio devices. BLINE_OUT_L AGND +5VA BLINE_OUT_R Be default, the pins labeled LINE OUT_R/BLINE_OUT_R and the pins LINE OUT_L/BLINE_OUT_L are shorted with jumper caps. Remove the caps only when you are connecting the front panel audio cable. MIC2 MICPWR Line out_R NC Line out_L FP_AUDIO P4P800-X ® P4P800-X Front panel audio connector 9.
10. GAME/MIDI connector (16-1 pin GAME) +5V J2B1 J2CX MIDI_OUT J2CY J2B2 MIDI_IN This connector supports a GAME/MIDI module. If a GAME/MIDI module is available, connect the GAME/MIDI cable to this connector. The GAME/MIDI port on the module connects a joystick or a game pad for playing games, and MIDI devices for playing or editing audio files. P4P800-X +5V J1B1 J1CX GND GND J1CY J1B2 +5V GAME ® P4P800-X Game connector The GAME/MIDI module is purchased separately. 11.
12. Serial connector (9-pin COM2 ) This 9-pin connector connects to a COM2 bracket. Connect the COM2 cable to this connector and install the bracket on an available slot in the rear panel of the chassis. COM2 PIN 1 P4P800-X ® P4P800-X Serial port connector The COM2 bracket is purchased separately. 13. System panel connector (10-1 pin PANEL) This connector accommodates several system front panel functions.
• Reset Switch Lead (Blue 2-pin RESET) This 2-pin connector connects to the case-mounted reset switch for rebooting the system without turning off the system power. • ATX Power Switch/Soft-off Switch Lead (Light Green 2-pin PWR) This connector connects a switch that controls the system power. Pressing the power switch turns the system between ON and SLEEP, or ON and SOFT OFF, depending on the BIOS or OS settings. Pressing the power switch while in the ON mode for more than 4 seconds turns the system OFF.
Chapter 2 This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
2.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. ASUS AFUDOS - Updates the BIOS using a bootable floppy disk in DOS mode. 2. ASUS EZ Flash - Updates the BIOS using a floppy disk during POST. 3. ASUS CrashFree BIOS 2 - Updates the BIOS using a bootable floppy disk or the motherboard support CD. Refer to the corresponding sections for details on these utilities.
c. Click Start, then select Run. d. From the Open box, type D:\bootdisk\makeboot a: then press , assuming that D: is your CD-ROM drive. e. Follow succeeding screen instructions. 2. Copy the original (or the latest) motherboard BIOS to the bootable floppy disk. 2.1.2 Using AFUDOS to update the BIOS To update the BIOS using the AFUDOS.EXE utility: 1. Visit the ASUS website (www.asus.com) to download the latest BIOS file for your motherboard. Save the BIOS file to a bootable floppy disk.
When the BIOS update process is complete, the utility returns to the DOS prompt. A:\>afudos /iP4P800X.ROM AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading file ..... done Erasing flash .... done Writing flash .... 0x0008CC00 (9%) Verifying flash .. done A:\> 5. Reboot the system from the hard disk. 2.1.3 Using AFUDOS to copy BIOS from PC You can use the AFUDOS.
3. The utility will copy the current system BIOS by default to the floppy disk. Make sure that the floppy disk has at least 600KB of free disk space and is not writeprotected. A:\>afudos /oMYBIOS03.ROM AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading flash ..... done A:\> When the copy process is complete, the utility returns to the DOS prompt. 2.1.
DO NOT shutdown or reset the system while updating the BIOS! Doing so may cause system boot failure! User recovery requested. Starting BIOS recovery... Checking for floppy... Floppy found! Reading file “P4P800X.ROM”. Completed. Start flashing... Flashed successfully. Rebooting. 2.1.
Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Floppy found! Reading file “P4P800X.ROM”. Completed. Start flashing... DO NOT shut down or reset the system while updating the BIOS! Doing so may cause system boot failure! 2. When the BIOS update process is complete, reboot the system. To recover the BIOS from the support CD: 1. Boot the system. 2. When a corrupted BIOS is detected, the following screen message appears. Bad BIOS checksum. Starting BIOS recovery... Checking for floppy...
2.2 BIOS Setup program This motherboard supports a programmable firmware hub (FWH) that you can update using the provided utility described in section “2.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you may want to change the configuration of your computer in the future.
2.2.1 BIOS menu screen Menu items Menu bar System Time System Date Legacy Diskette A Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Fourth IDE Master IDE Configuration Configuration fields [11:10:19] [Thu 03/27/2003] [1.44M, 3.5 in] :[ST320413A] :[ASUS CD-S340] :[Not Detected] :[Not Detected] :[Not Detected] :[Not Detected] System Information General help Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time.
2.2.4 Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting Main shows the Main menu items. The other items (Advanced, Power, Boot, and Exit) on the menu bar have their respective menu items. System Time System Date Legacy Diskette A Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Fourth IDE Master IDE Configuration [11:10:19] [Thu 03/27/2003] [1.44M, 3.
2.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears giving you an overview of the basic system information. Refer to section “2.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them. System Time System Date Legacy Diskette A Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Fourth IDE Master IDE Configuration [11:51:19] [Thu 08/05/2003] [1.44M, 3.
2.3.4 Primary and Secondary IDE Master/Slave; Third and Fourth IDE Master While entering Setup, BIOS auto-detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press Enter to display the IDE device information. Primary IDE Master Device : Hard Disk Vendor : ST320413A Size : 20.
PIO Mode [Auto] Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] Selects the DMA mode. Configuration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] SMART Monitoring [Auto] Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled] 32Bit Data Transfer [Disabled] Enables or disables 32-bit data transfer.
Enhanced Mode Support On [S-ATA] The default setting S-ATA allows you to use native OS (Windows 2000/XP) on Serial ATA and Parallel ATA ports. We recommend that you do not change the default setting for better OS compatibility. In this setting, you may use legacy OS (Windows ME/98/98SE/NT4.0) on the Parallel ATA ports only if you did not install any Serial ATA device. The P-ATA+S-ATA and P-ATA options are for advanced users only.
AMI BIOS This item displays the auto-detected BIOS information. Processor This item displays the auto-detected CPU specification. System Memory This item displays the auto-detected system memory. 2.4 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Take caution when changing the settings of the Advanced menu items. Incorrect field values may cause the system to malfunction.
CPU VCore Voltage [Auto] Allows you to select a specific CPU VCore voltage. The configurations depends on the type of CPU installed. Refer to the CPU documentation before setting the CPU VCore voltage. A very high Vcore voltage may severely damage the CPU! When you set the AI Overclocking Tuner item to [Manual], the related overclocking items appear.
DDR Reference Voltage [Auto] Allows you to select a specific DDR Reference voltage. Configuration options: [Auto] [2.658V] [2.551V] 2.4.2 CPU Configuration The items in this menu show the CPU-related information auto-detected by BIOS. Configure advanced CPU settings Manufacturer: Brand String: Frequency : FSB Speed : Cache L1 Cache L2 Cache L3 Intel Intel(R) Pentium(R) 4 Family CPU 2.
2.4.3 Chipset The Chipset menu items allow you to change the advanced chipset settings. Select an item then press Enter to display the sub-menu. Advanced Chipset Settings Warning: Setting wrong values in below sections may cause system to malfunction.
DRAM Precharge Delay [8 Clocks] Configuration options: [8 Clocks] [7 Clocks] [6 Clocks] [5 Clocks] DRAM Burst Length [8 Clocks] Configuration options: [4 Clocks] [8 Clocks] Memory Acceleration Mode [Auto] This field when [Enabled] minimize latencies from CPU to memory to boost system performance. Configuration options: [Auto] [Enabled] DRAM Idle Timer [Auto] Configuration options: [Infinite] [0T] [8T] [16T] [64T] [Auto] DRAM Refresh Mode [Auto] Configuration options: [Auto] [15.6 uSec] [7.
2.4.4 Onboard Devices Configuration Onboard AC’97 Audio Onboard LAN Onboard LAN Boot ROM [Auto] [Enabled] [Disabled] Serial Port1 Address Parallel Port Address Parallel Port Mode Parallel Port IRQ OnBoard Game/MIDI Port [3F8/IRQ4] [Disabled] [Normal] [IRQ7] [Disabled] [Enter] to select OnBoard AC’97 Audio [Auto] [Auto] allows the BIOS to detect whether you are using any audio device.
ECP Mode DMA Channel [DMA3] Allows you to set the Parallel Port ECP DMA. This item appears only when the Parallel Port Mode is set to ECP. Configuration options: [DMA0] [DMA1] [DMA3] Parallel Port IRQ [IRQ7] Configuration options: [IRQ5] [IRQ7] Onboard Game/MIDI Port [Disabled] Allows you to select the Game Port address or to disable the port. Configuration options: [Disabled] [200/300] [200/330] [208/300] [208/330] 2.4.
PCI Latency Timer [64] Allows you to select the value in units of PCI clocks for the PCI device latency timer register. Configuration options: [32] [64] [96] [128] [160] [192] [224] [248] Allocate IRQ to PCI VGA [Yes] When set to [Yes], BIOS assigns an IRQ to PCI VGA card if the card requests for an IRQ. When set to [No], BIOS does not assign an IRQ to the PCI VGA card even if requested.
Legacy USB Support [Auto] Allows you to enable or disable support for legacy USB devices. Setting to Auto allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled. Configuration options: [Disabled] [Enabled] [Auto] USB 2.0 Controller [Enabled] Allows you to enable or disable the USB 2.0 controller. Configuration options: [Disabled] [Enabled] USB 2.
2.5 Power menu The Power menu items allow you to change the settings for the Advanced Power Management (APM) feature. Select an item then press to display the configuration options. Suspend Mode Repost Video on S3 Resume ACPI 2.0 Support ACPI APIC Support BIOS-->AML ACPI table Select the ACPI state used for System Suspend. [Auto] [No] [No] [Enabled] [Enabled] APM Configuration Hardware Monitor 2.5.1 Suspend Mode [Auto] Allows you to select the ACPI state to be used for system suspend.
2.5.6 Advanced Power Management (APM) Configuration Power Management/APM Video Power Down Mode Hard Disk Power Down Mode Suspend Time Out Throttle Slow Clock Ratio [Enabled] [Disabled] [Disabled] [Disabled] [50%] Power Button Mode Restore on AC Power Loss [On/Off] [Power Off] Power Power Power Power Power [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] On On On On On By By By By By RTC Alarm External Modems PCI Devices PS/2 Keyboard PS/2 Mouse Enable or disable APM.
Restore on AC Power Loss [Power Off] When set to Power Off, the system goes into off state after an AC power loss. When set to Power On, the system goes on after an AC power loss. When set to Last State, the system goes into either off or on state whatever was the system state before the AC power loss. Configuration options: [Power Off] [Power On] [Last State] Power On By RTC Alarm [Disabled] Allows you to enable or disable RTC to generate a wake event.
2.5.7 Hardware Monitor CPU Temperature Hardware Monitor CPU Temperature MB Temperature [40.5ºC/102.5ºF] [33ªC/91ºF] CPU Fan Speed Chassis Fan Speed [3260RPM] [N/A] VCORE Voltage 3.3V Voltage 5V Voltage 12V Voltage [ 1.504V] [ 3.360V] [ 5.160V] [11.328V] CPU Temperature [xxxC/xxxF] MB Temperature [xxxC/xxxF] The onboard hardware monitor automatically detects and displays the CPU and motherboard temperatures. Select Disabled if you do not wish to display the detected temperatures.
2.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press Enter to display the sub-menu. Boot Settings Specifies the Boot Device Priority sequence. Boot Device Priority Boot Settings Configuration Security 2.6.1 Boot Device Priority Boot Device Priority 1st Boot Device 2nd Boot Device 3rd Boot Device [1st FLOPPY DRIVE] [PM-ST320413A] [SM-ASUS CD-S360] Specifies the boot sequence from the available devices.
Quick Boot [Enabled] Enabling this item allows the BIOS to skip some power on self tests (POST) while booting to decrease the time needed to boot the system. When set to [Disabled], BIOS performs all the POST items. Configuration options: [Disabled] [Enabled] Full Screen Logo [Enabled] This allows you to enable or disable the full screen logo display feature. Configuration options: [Disabled] [Enabled] Make sure that the Full Screen Logo item is set to [Enabled] if you wish to use the ASUS MyLogo™ feature.
2.6.3 Security The Security menu items allow you to change the system security settings. Select an item then press Enter to display the configuration options. to change password. again to disable password. Security Settings Supervisor Password User Password : Not Installed : Not Installed Change Supervisor Password Change User Password Clear User Password Boot Sector Virus Protection [Disabled] Change Supervisor Password Select this item to set or change the supervisor password.
After you have set a supervisor password, the other items appear to allow you to change other security settings. Security Settings Supervisor Password User Password : Installed : Not Installed Change Supervisor Password User Access Level Change User Password Clear User Password Password Check Boot Sector Virus Protection to change password. again to disabled password.
Boot Sector Virus Protection [Disabled] Allows you to enable or disable the boot sector virus protection. Configuration options: [Disabled] [Enabled] 2.7 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items. Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Exit system setup after saving the changes. F10 key can be used for this operation.
Chapter 3 This chapter describes the contents of the support CD that comes with the motherboard package.
3.1 Install an operating system ® This motherboard supports Windows® 98SE/ME/2000/XP/2003 Server operating system (OS). Always install the latest OS version and corresponding updates so you can maximize the features of your hardware. Because motherboard settings and hardware options vary, use the setup procedures presented in this chapter for general reference only. Refer to your OS documentation for more information. 3.
3.2.2 Drivers menu The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. Intel® Chipset Inf Update program This item installs the Intel® Chipset INF Update Program that enables Plug-n-Play INF support for Intel chipset components. This utility installs to the target system the Windows INF files that outline to the operating system how the chipset components will be configured.
Install ASUS Update This program allows you to download the latest version of the BIOS from the ASUS website. Before using the ASUS Update, make sure that you have an Internet connection so you can connect to the ASUS website. Installing ASUS Update also installs ASUS Mylogo™. To use the MyLogo™ feature, set the BIOS “Quick Boot” item to [Enabled]. See section “2.6.3 Boot Settings Configuration” in page 2-32.
