Premium Motherboard P5AD2-E
E1792 First Edition V1 October 2004 Copyright © 2004 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Notices ................................................................................................ vi Safety information ............................................................................. vii About this guide ............................................................................... viii Typography ......................................................................................... ix P5AD2-E Premium specifications summary .........................................
Contents Chapter 3: Powering up 3.1 3.2 3.3 Starting up for the first time ................................................ 3-1 Powering off the computer .................................................. 3-2 3.2.1 Using the OS shut down function ........................... 3-2 3.2.2 Using the dual function power switch .................... 3-2 ASUS POST Reporter™ .......................................................... 3-3 3.3.1 Vocal POST messages ............................................ 3-3 3.3.
Contents 4.5 4.6 4.7 4.4.7 PCI PnP ................................................................. 4-30 4.4.8 Speech Configuration ........................................... 4-31 4.5.1 Suspend Mode ...................................................... 4-32 4.5.2 Repost Video on S3 Resume ................................ 4-32 4.5.3 ACPI 2.0 Support .................................................. 4-32 4.5.4 ACPI APIC Support ................................................ 4-32 Power menu .........
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This manual contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports. • Chapter 2: Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components.
Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. D A N G E R / W A R N I N G : Information to prevent injury to yourself when trying to complete a task. C A U T I O N : Information to prevent damage to the components when trying to complete a task. I M P O R T A N T : Instructions that you MUST follow to complete a task. N O T E : Tips and additional information to help you complete a task.
P5AD2-E Premium specifications summary CPU LGA775 socket for Intel® Pentium® 4/Celeron processor Compatible with Intel® PCG 04A and 04B processors Supports Intel® Hyper-Threading Technology Chipset Northbridge: Intel® 925XE Memory Controller Hub (MCH) Southbridge: Intel® ICH6R Front Side Bus 1066/800 MHz Memory Dual-channel memory architecture 4 x 240-pin DIMM sockets support unbufferred non-ECC 711/533 MHz DDR2 memory modules Up to 4 GB system memory Native DDR2-711 support Expansion slots 1 x PCI
P5AD2-E Premium specifications summary IEEE 1394 TI 1394b controller supports: - 2 x IEEE 1394b connectors - 1 x IEEE 1394a ports Overclocking features ASUS AI Overclocking ASUS NOS (Non-delay Overclocking System) ASUS C.P.R.
P5AD2 Premium specifications summary Internal connectors (continuation) CPU, chassis (x2), and power fan connectors ATX power connectors (24-pin and 4-pin) System panel connector Power Requirement ATX power supply (with 24-pin and 4-pin 12 V plugs) ATX 12V 2.0 compliant Form Factor ATX form factor: 12 in x 9.6 in (30.5 cm x 24.
This chapter describes the motherboard features and the new technologies it supports.
Chapter summary 1 1.1 Welcome! .............................................................................. 1-1 1.2 Package contents ................................................................. 1-1 1.3 Special features ....................................................................
1.1 Welcome! Thank you for buying an ASUS® P5AD2-E Premium motherboard! The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your motherboard package for the following items.
1.3 Special features 1.3.1 Product highlights Latest processor technology The motherboard comes with a 775-pin surface mount Land Grid Array (LGA) socket designed for the Intel® Pentium® 4 processor in the 775-land package. The motherboard supports the Intel® Pentium® 4 processor with 1066/800/533 MHz Front Side Bus (FSB). The motherboard also supports the Intel® Hyper-Threading Technology and is fully compatible with Intel® 04B and 04A processors. See page 2-7 for details.
Triple RAID solution Onboard RAID controllers provide the motherboard with multi-RAID functionality that allows you to select the best RAID solution using IDE or Serial ATA hard disk drives. The Intel® ICH6R allows RAID 0 and RAID 1 configuration for four SATA connectors and supports the Intel® Matrix Storage Technology. See page 2-26 for details. The Sil3114R controller supports four additional SATA connectors and allows RAID 0, RAID 1, RAID 10, and a software patch to support RAID 5.
S/PDIF digital sound ready The motherboard supports the S/PDIF technology through the S/PDIF interfaces on the rear panel and at midboard. The S/PDIF technology turns your computer into a high-end entertainment system with digital connectivity to powerful audio and speaker systems. See page 2-23 for details. IEEE 1394b/a support The motherboard implements the IEEE 1394b standard that allows up to 800 Mbps transfer rates, and increases the computer-to-electronic device operational distance from 4.
1.3.2 ASUS AI Proactive features ASUS Stack Cool™ ASUS Stack Cool™ is an ideal thermal solution that reduces the heat dissipated by large capacitors and motherboard components. Stack Cool™ is a specially designed PCB installed under the motherboard CPU socket that effectively lowers the system temperature by as much as 10º Celsius. Cooler system temperature means more stable system performance, longer component life, and more silent operation. See page 2-3 for details.
1.3.3 Innovative ASUS features ASUS Hyper Path 2 technology The ASUS Hyper Path 2 technology optimizes the full potential of the Intel® chipset by shortening the latency time between the CPU and the system memory. Enabling Hyper Path 2 on systems with the Intel® PAT improves memory performance without affecting system stability. See page 4-27 for details. Native DDR2-711 support This motherboard offers native DDR2-711 memory support to ensure superior system performance.
This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
Chapter summary 2 2.1 Before you proceed .............................................................. 2-1 2.2 Motherboard overview .......................................................... 2-2 2.3 Central Processing Unit (CPU) .............................................. 2-7 2.4 System memory ................................................................. 2-14 2.5 Expansion slots ...................................................................
2.1 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Use a grounded wrist strap or touch a safely grounded object or to a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity. • Hold components by the edges to avoid touching the ICs on them.
2.2 Motherboard overview Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components. 2.2.1 Placement direction When installing the motherboard, make sure that you place it into the chassis in the correct orientation.
2.2.3 ASUS Stack Cool The motherboard comes with the ASUS Stack Cool, an innovative thermal solution that provides supplementary cooling to the motherboard. Stack Cool is a mini-PCB installed underneath the motherboard CPU socket to conduct heat away from motherboard components. Stack Cool effectively lowers the motherboard temperature by as much as 10ºC.
2.2.4 Motherboard layout MS1 24.5cm (9.6in) Super I/O ATX12V1 Side Speaker Out R Below: Intel 925XE Center/Subwoofer Top:Line In Center:Line Out Bottom:Mic In LAN2 Marvell 88E8053 FLOPPY1 PRI_IDE1 USBPW12 USBPW34 EATXPWR Top:Rear Speaker Out Center: DDR2 DIMM_B2 (64 bit,240-pin module) USB2.0 Top: T: USB3 LAN port B: USB4 DDR2 DIMM_B1 (64 bit,240-pin module) Top: USB1 USB2 1394 DDR2 DIMM_A1 (64 bit,240-pin module) Bottom: DDR2 DIMM_A2 (64 bit,240-pin module) P5AD2-E CPU_FAN1 30.
2.2.5 Layout contents Slots Page 1. DDR2 DIMM slots 2-14 2. PCI slots 2-19 3. PCI Express slot 2-19 Jumpers Page 1. Clear RTC RAM (3-pin CLRTC1) 2-20 2. USB Device wake-up (3-pin USBPW12, USBPW34, USBPW56, USBPW78) 2-21 3. Keyboard power (3-pin KBPWR1) 2-21 Rear panel connectors Page 1. Parallel port 2-22 2. IEEE 1394a port 2-22 3. LAN (RJ-45) port 2-22 4. Rear Speaker Out port (gray) 2-22 5. Side Speaker Out port (black) 2-22 6. Line In port (light blue) 2-22 7.
Internal connectors Page 1. 2. Floppy disk drive connector (34-1 pin FLOPPY) Primary IDE connector (40-1 pin PRI_IDE1) 2-24 2-24 3. IDE RAID connectors (40-1 pin PRI_RAID1 [red], SEC_RAID1 [red]) 2-25 4. Serial ATA connectors (7-pin SATA1 [red], SATA2 [red], SATA3 [black], SATA4 [black) 2-26 5. Serial ATA RAID connectors (7-pin SATA_RAID1, SATA_RAID2, SATA_RAID3, SATA_RAID4) 2-27 6. Optical drive audio connector (4-pin CD) 2-28 7. Digital audio connector (6-1 pin SPDIF) 2-28 8.
2.3 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA775 socket designed for the Intel® Pentium® 4 processor in the 775-land package 2.3.1 • Upon purchase of the motherboard, make sure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components.
2. Press the load lever with your thumb (A), then move it to the left (B) until it is released from the retention tab. Retention tab A PnP cap Load lever B This side of the socket box should face you. To prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU. 3. Lift the load lever in the direction of the arrow to a 135º angle. 4.
6. Close the load plate (A), then push the load lever (B) until it snaps into the retention tab. A B The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU! Notes on Intel® Hyper-Threading Technology • This motherboard supports Intel® Pentium® 4 CPUs in the 775-land package with Hyper-Threading Technology. • Hyper-Threading Technology is supported under Windows® XP/2003 Server and Linux 2.4.
2.3.2 Installing the CPU heatsink and fan The Intel® Pentium® 4 LGA775 processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. • When you buy a boxed Intel® Pentium® 4 processor, the package includes the CPU fan and heatsink assembly. If you buy a CPU separately, make sure that you use only Intel®-certified multi-directional heatsink and fan.
2. 3. Push down two fasteners at a time in a diagonal sequence to secure the heatsink and fan assembly in place. A B B A B A A B Connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN1. GND CPU FAN PWR CPU FAN IN CPU FAN PWM P5AD2-E PREMIUM CPU_FAN1 Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector.
2.3.3 Uninstalling the CPU heatsink and fan To uninstall the CPU heatsink and fan: 1. Disconnect the CPU fan cable from the connector on the motherboard. 2. Rotate each fastener counterclockwise. 3. Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and fan assembly from the motherboard. B A A B 4. 2-12 A B B A Carefully remove the heatsink and fan assembly from the motherboard.
5. Rotate each fastener clockwise to ensure correct orientation when reinstalling. Narrow end of the groove The narrow end of the groove should point outward after resetting. (The photo shows the groove shaded for emphasis.) Refer to the documentation in the boxed or stand-alone CPU fan package for detailed information on CPU fan installation.
2.4 System memory 2.4.1 Overview The motherboard comes with four Double Data Rate 2 (DDR2) Dual Inline Memory Modules (DIMM) sockets. A DDR2 module has the same physical dimensions as a DDR DIMM but has a 240-pin footprint compared to the 184-pin DDR DIMM. DDR2 DIMMs are notched differently to prevent installation on a DDR DIMM socket.
DDR2 (533 MHz) Qualified Vendors List DIMM support Size Vendor Model CL B r a n d Side(s) C o m p o n e n t A B C 512 MB SAMSUNG M378T6553BG0-CD5 N/A N/A SS K4T51083QB-GCD5 • • • 1024 MB SAMSUNG M378T2953BG0-CD5 N/A N/A DS K4T51083QB-GCD5 • • • 256 MB SAMSUNG M378T3253FG0-CD5 N/A N/A SS K4T56083QF-GCD5 • • • 512 MB SAMSUNG M378T6453FG0-CD5 N/A N/A DS K4T56083QF-GCD5 • • • 512 MB Infineon HYS64T64000GU-3.
2.4.3 Installing a DIMM Unplug the power supply before adding or removing DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components. 2 To install a DIMM: 1. Unlock a DIMM socket by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. 3.
2.5 Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. 2.5.1 Installing an expansion card To install an expansion card: 1.
2.5.
2.5.4 PCI slots The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The figure shows a LAN card installed on a PCI slot. 2.5.5 PCI Express x16 slot This motherboard supports PCI Express x16 graphic cards that comply with the PCI Express specifications. The following figure shows a graphics card installed on the PCI Express x16 slot. 2.5.
2.6 1. Jumpers Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the onboard battery. 3. Move the jumper cap from pins 1-2 (default) to pins 2-3.
2. USB device wake-up jumpers (3-pin USBPW12, USBPW34, USBPW56, USBPW78) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode). The USBPWR12 and USBPWR34 jumpers are for the rear USB ports.
2.7 Connectors 2.7.1 Rear panel connectors 1 2 3 4 5 6 7 17 1. 16 15 14 13 12 11 10 9 8 P a r a l l e l p o r t . This 25-pin port connects a parallel printer, a scanner, or other devices. I E E E 1 3 9 4 a p o r t . This 6-pin IEEE 1394a port provides high-speed connectivity for audio/video devices, storage peripherals, PCs, or portable devices. L A N ( R J - 4 5 ) p o r t . This port allows Gigabit connection to a Local Area Network (LAN) through a network hub.
8. W i r e l e s s L A N a n t e n n a p o r t (Wireless Edition only).. This port connects to the optional dipolar antenna for the onboard WiFi-g™ wireless LAN solution. 9. W i r e l e s s L A N L E D (Wireless Edition only).. This green A I R LED indicates the data transmission status of the onboard wireless LAN adapter. Refer to the table below for the LED indications. Wireless LAN LED indications Status Indication On The onboard WiFi-g™ is on but has no data activity.
2.7.2 1. Internal connectors Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. P5AD2-E PREMIUM Pin 5 on the connector is removed to prevent incorrect cable connection when using a FDD cable with a covered Pin 5. PIN 1 FLOPPY NOTE: Orient the red markings on the floppy ribbon cable to PIN 1.
3. IDE RAID connectors (40-1 pin PRI_RAID1 [red], SEC_RAID1 [red]) These connectors are for Ultra ATA 133/100/66 signal cables. The IDE RAID connectors support up to four IDE hard disk drives that you can configure as a disk array through the onboard IDE RAID controller. Refer to Chapter 5 for details on how to set up RAID configurations. P5AD2-E PREMIUM These connectors are set to I D E M o d e by default.
4. Serial ATA connectors (7-pin SATA1 [red], SATA2 [red], SATA3 [black], SATA4 [black]) These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives. If you installed Serial ATA hard disk drives, you can create a RAID 0 or RAID 1 configuration with the Intel® Matrix Storage Technology through the onboard Intel® ICH6R RAID controller. Refer to Chapter 5 for details on how to set up Serial ATA RAID configurations.
Serial ATA hard disk drive connection 5. Connector Color Setting Use SATA1/SATA2 Red Master Boot disk SATA3/SATA4 Black Slave Data disk Serial ATA RAID connectors (7-pin SATA_RAID1, SATA_RAID2, SATA_RAID3, SATA_RAID4) These connectors are for Serial ATA signal cables. These connectors support up to four Serial ATA hard disk drives that you can configure as a disk array through the onboard SATA RAID controller. Refer to Chapter 5 for details on how to set up Serial ATA RAID configurations.
6. Digital audio connector (6-1 pin SPDIF) This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port(s). Connect the S/PDIF module cable to this connector, then install the module to a slot opening at the back of the system chassis. GND GND P5AD2-E PREMIUM The S/PDIF module is purchased separately.
8. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC’97 audio standard.
1 0 . I E E E 1 3 9 4 b p o r t connectors (10-1 pin IE1394B_1, I E 1 3 9 4 B _ 2 [ p u r p l e ]])) These connectors are for IEEE 1394b ports. Connect the IEEE 1394b module cable (purple) to this connector, then install the module to a slot opening at the back of the system chassis. Refer to the IEEE 1394b driver information on page 5-9 for details. P5AD2-E PREMIUM You can connect an optional IEEE 1394a module cable to these connectors.
P5AD2-E PREMIUM 1 2 . Serial port connector (10-1 pin COM1) This connector is for a serial (COM) port. Connect the serial port module cable to this connector, then install the module to a slot opening at the back of the system chassis. COM1 PIN 1 ® P5AD2-E PREMIUM Serial port connector 1 3 . CPU, Chassis, and Power Fan connectors (3-pin CPU_FAN1, PWR_FAN1, CHA_FAN1, CHA_FAN2) The fan connectors support cooling fans of 350 mA ~ 2000 mA (24 W max.) or a total of 1 A ~ 3.48 A (41.76 W max.) at +12V.
1 4 . Chassis intrusion connector (4-1 pin CHASSIS1) This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. The signal is then generated as a chassis intrusion event.
1 6 . ATX power connectors (24-pin EATXPWR1, 4-pin ATX12V1) These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. • Use of an ATX 12 V Specification 2.0 -compliant power supply unit (PSU) that provides a minimum power of 350 W is recommended for a fully-configured system.
1 7 . System panel connector (20-pin PANEL1) +5V Ground Ground Speaker PLED- SPEAKER IDE_LED Reset Ground PWR Ground PANEL1 IDE_LED+ IDE_LED- ® PLED PLED+ P5AD2-E PREMIUM This connector supports several chassis-mounted functions. RESET PWRSW P5AD2-E PREMIUM System panel connector The sytem panel connector is color-coded for easy connection. Refer to the connector description below for details.
This chapter describes the power up sequence, the vocal POST messages, and ways of shutting down the system.
Chapter summary 3 3.1 Starting up for the first time ................................................ 3-1 3.2 Powering off the computer .................................................. 3-2 3.3 ASUS POST Reporter™ ..........................................................
3.1 Starting up for the first time 1. After making all the connections, replace the system case cover. 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: a. Monitor b. External SCSI devices (starting with the last device on the chain) c. System power 6.
3.2 Powering off the computer 3.2.1 Using the OS shut down function If you are using Windows® 2000: 2. Click the S t a r t button then click S h u t D o w n . . . Make sure that the S h u t D o w n option button is selected, then click the O K button to shut down the computer. 3. The power supply should turn off after Windows® shuts down. 1. If you are using Windows® XP: 2. Click the S t a r t button then select T u r n O f f C o m p u t e r .
3.3 ASUS POST Reporter™ This motherboard includes the Winbond speech controller to support a special feature called the ASUS POST Reporter™. This feature lets you hear vocal messages during POST that alerts you of system events and boot status. In case of a boot failure, you will hear the specific cause of the problem. These POST messages are customizable using the Winbond Voice Editor software that came with your package. You can record your own messages to replace the default messages. 3.3.
POST Message Action CPU temperature too high • Check if the CPU fan is working properly. CPU fan failed • Check the CPU fan and make sure it turns on after you apply power to the system. • Make sure that your CPU fan supports the fan speed detection function. • Check your power supply and make sure it is not defective. • Call ASUS technical support for assistance. See the “ASUS contact information” on the inside front cover of this user guide.
3.3.2 Winbond Voice Editor The Winbond Voice Editor software allows you to customize the vocal POST messages. You can install this application from the support CD. To avoid conflicts, do not run the Winbond Voice Editor while running the ASUS PC Probe application. Launching the Voice Editor You can launch the program from the Windows® desktop by clicking S t a r t > A l l P r o g r a m s > W i n b o n d V o i c e E d i t o r > V o i c e E d i t o rr. The Winbond Voice Editor screen appears.
Changing the default language To change the default language: 1. Click the L o a d button from the Voice Editor main window. A window with the available languages appears. 2. Select your desired language, then click O p e n n. The event messages for the language you selected appear on the Voice Editor main window. Not all events on some languages have a corresponding message due to file size constraints. 3. 4. Click the W r i t e button from the Voice Editor main window to update the EEPROM.
Customizing your POST messages The Voice Editor application allows you to record your own POST messages if your language is not supported or if you wish to to replace the pre-installed wave files. To customize your POST messages. 1. Launch the Voice Editor application and note the list of POST events on the leftmost column of the screen. 2. Prepare your message for each event. 3. Use a recording software (e.g. Windows® Recorder) to record your messages, then save the messages as wave files (.WAV).
6. Select a POST event on the Voice Editor main window, then click the E d i t button. The E v e n t S o u n d E d i t o r window appears. 7. Locate and select your wave file for the event, then click on the arrow opposite Voice1. The file you select appears on the space next to it. Click O K to return to the Voice Editor main window. 8. 9. Do steps 6 to 8 for the other events. 10. When done, click S a v e e. A window appears prompting you to save your configuration. 11. Type a file name with an .
This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
Chapter summary 4 4.1 Managing and updating your BIOS ........................................ 4-1 4.2 BIOS setup program ........................................................... 4-11 4.3 Main menu .......................................................................... 4-14 4.4 Advanced menu .................................................................. 4-19 4.5 Power menu ........................................................................ 4-31 4.6 Boot menu .....................
4.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. 2. 3. 4. A S U S A F U D O S (Updates the BIOS in DOS mode using a bootable floppy disk.) A S U S C r a s h F r e e B I O S 2 (Updates the BIOS using a bootable floppy disk or the motherboard support CD when the BIOS file fails or gets corrupted.) A S U S E Z F l a s h (Updates the BIOS in DOS mode using a floppy disk or the motherboard support CD.
Windows® 2000 environment To create a set of boot disks for Windows® 2000: a. Insert a formatted, high density 1.44 MB floppy disk into the drive. b. Insert the Windows® 2000 CD to the optical drive. c. Click S t a r tt, then select R u n n. d. In the O p e n field, type D:\bootdisk\makeboot a: assuming that D is your optical drive letter. e. Press , then follow screen instructions to continue. 2. Copy the original or the latest motherboard BIOS file to the bootable floppy disk. 4.1.
3. Press . The utility copies the current BIOS file to the floppy disk. A:\>afudos /oOLDBIOS1.rom AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB)) Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading flash ..... done Write to file...... ok A:\> The utility returns to the DOS prompt after copying the current BIOS file. Updating the BIOS file To update the BIOS file using the AFUDOS utility: 1. Visit the ASUS website (www.asus.
4. The utility verifies the file and starts updating the BIOS. A:\>afudos /iP5AD2E.rom AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB)) Copyright (C) 2002 American Megatrends, Inc. All rights reserved. WARNING!! Do not turn off power during flash BIOS Reading file ....... done Reading flash ...... done Advance Check ...... Erasing flash ...... done Writing flash ...... 0x0008CC00 (9%) Do not shut down or reset the system while updating the BIOS to prevent system boot failure! 5.
4.1.3 ASUS CrashFree BIOS 2 utility The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can update a corrupted BIOS file using the motherboard support CD or the floppy disk that contains the updated BIOS file. • Prepare the motherboard support CD or the floppy disk containing the updated motherboard BIOS before using this utility.
Recovering the BIOS from the support CD To recover the BIOS from the support CD: 1. Remove any floppy disk from the floppy disk drive, then turn on the system. 2. Insert the support CD to the optical drive. 3. The utility displays the following message and automatically checks the floppy disk for the original or updated BIOS file. Bad BIOS checksum. Starting BIOS recovery... Checking for floppy...
4.1.4 ASUS EZ Flash utility The ASUS EZ Flash feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS-based utility. The EZ Flash utility is built-in the BIOS chip so it is accessible by pressing + during the Power-On Self Tests (POST). To update the BIOS using EZ Flash: 1. Visit the ASUS website (www.asus.com) to download the latest BIOS file for the motherboard and rename the same to P 5 A D 2 E . R O M M. 2.
4.1.5 ASUS Update utility The ASUS Update is a utility that allows you to manage, save, and update the motherboard BIOS in Windows® environment. The ASUS Update utility allows you to: • Save the current BIOS file • Download the latest BIOS file from the Internet • Update the BIOS from an updated BIOS file • Update the BIOS directly from the Internet, and • View the BIOS version information. This utility is available in the support CD that comes with the motherboard package.
Updating the BIOS through the Internet To update the BIOS through the Internet: 1. Launch the ASUS Update utility from the Windows® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate e. The ASUS Update main window appears. 2. Select U p d a t e B I O S f r o m t h e I n t e r n e t option from the drop-down menu, then click N e x tt. ASUS P5AD2-E Premium 3. Select the ASUS FTP site nearest you to avoid network traffic, or click A u t o S e l e c tt. Click N e x tt.
4. From the FTP site, select the BIOS version that you wish to download. Click Next. 5. Follow the screen instructions to complete the update process. The ASUS Update utility is capable of updating itself through the Internet. Always update the utility to avail all its features. Updating the BIOS through a BIOS file To update the BIOS through a BIOS file: 1. 2. 3. 4.
4.2 BIOS setup program This motherboard supports a programmable firmware chip that you can update using the provided utility described in section “4.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you can change the configuration of your computer in the future.
4.2.1 BIOS menu screen Menu items Menu bar System Time System Date Legacy Diskette A Language Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Fourth IDE Master IDE Configuration Configuration fields [11:10:19] [Thu 03/27/2003] [1.44M, 3.5 in] [English] :[ST320413A] :[ASUS CD-S340] :[Not Detected] :[Not Detected] :[Not Detected] :[Not Detected] System Information Sub-menu items 4.2.2 General help Use [ENTER], [TAB] or [SHIFT-TAB] to select a field.
4.2.4 Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting M a i n shows the Main menu items. System Time System Date Legacy Diskette A Language Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Fourth IDE Master IDE Configuration [11:10:19] [Thu 03/27/2003] [1.44M, 3.5 in] [English] :[ST320413A] :[ASUS CD-S340] :[Not Detected] :[Not Detected] :[Not Detected] :[Not Detected] 4.2.
4.3 Main menu When you enter the BIOS Setup program, the M a i n menu screen appears, giving you an overview of the basic system information. Refer to section “4.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them. System Time System Date Legacy Diskette A Language Primary IDE Master Primary IDE Slave Third IDE Master Third IDE Slave Fourth IDE Master Fourth IDE Slave IDE Configuration [11:51:19] [Thu 05/07/2004] [1.44M, 3.
4.3.5 Primary, Third and Fourth IDE Master/Slave The BIOS automatically detects the connected IDE devices. There is a separate sub-menu for each IDE device. Select a device item, then press to display the IDE device information. Primary IDE Master Device : Hard Disk Vendor : ST320413A Size : 20.
PIO Mode [Auto] Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4] SMART Monitoring [Auto] Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled] 32Bit Data Transfer [Disabled] Enables or disables 32-bit data transfer. Configuration options: [Disabled] [Enabled] 4.3.6 IDE Configuration The items in this menu allow you to set or change the configurations for the IDE devices installed in the system.
Onboard IDE Operate Mode [Enhanced Mode] Allows selection of the IDE operation mode depending on the installed operating system (OS). Set to [Enhanced Mode] if you are using native OS including Windows® 2000/XP. Configuration options: [Compatible Mode] [Enhanced Mode] Enhanced Mode Support On [S-ATA] Allows you to use native OS on Serial ATA and Parallel ATA ports. It is recommend that you do not change the default setting for better OS compatibility.
IDE Detect Time Out [35] Selects the time out value for detecting ATA/ATAPI devices. Configuration options: [0] [5] [10] [15] [20] [25] [30] [35] 4.3.7 System Information This menu gives you an overview of the general system specifications. The BIOS automatically detects the items in this menu. AMIBIOS Version : 08.00.10 Build Date : 09/22/04 Processor Type Speed Count : Genuine Intel(R) CPU 3.
4.4 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Take caution when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. JumperFree Configuration LAN Cable Status USB Configuration Adjust system frequency/voltage. CPU Configuration Chipset Onboard Devices Configuration PCIPnP Speech Configuration 4.4.
Performance Mode [Auto] Allows enhanced system performance. setting to [Turbo] may cause the system to become unstable. If this happens, revert to the default setting [Auto]. Configuration options: [Auto] [Standard] [Turbo] AiBooster Support [Enabled] Enables or disables the system support for the Ai Booster overclocking application. Refer to the Ai Booster help file for details. The following item appears only when you install a CPU that supports the lock free feature.
PCI Clock Synchronization Mode [Auto] Allows you to synchronize the PCI frequency with the PCI Express or CPU frequency. Configuration options: [To CPU] [33.33MHz] [Auto] Spread Spectrum [Auto] Allows you to enable or disable the clock generator spread spectrum. Configuration options: [Disabled] [Enabled] [Auto] The following items also appear when the A I O v e r c l o c k i n g item is set to [AI NOS]. Memory Voltage [Auto] Allows you to select the DDR2 reference voltage.
The following item appears only when the A I O v e r c l o c k i n g item is set to [Overclock Profile]. Overclock Options [Overclock 5%] Allows you to overclock the CPU speed through the available preset values. Configuration options: [Overclock 5%] [FSB888/DDR2-667] [Overclock 10%] [FSB1000/DDR2-667] [Overclock 15%] [FSB1200/DDR2-600] [Overclock 20%] [FSB1200/DDR2-800] [Overclock 30%] [FSB1333/DDR2-667] The following item appears only when the A I O v e r c l o c k i n g item is set to [AI NOS].
4.4.2 LAN Cable Status This menu displays the status of the Local Area Network (LAN) cable connected to the LAN (RJ-45) port. POST Check LAN Cable LAN Cable Status Pair Status Length 1-2 3-6 4-5 7-8 Normal Normal Normal Normal N/A N/A N/A N/A 1-2 3-6 4-5 7-8 Normal Normal Normal Normal N/A N/A N/A N/A [Disabled] Check LAN cable during POST. POST Check LAN Cable [Disabled] Allows you to enable or disable LAN cable check during POST.
4.4.3 USB Configuration The items in this menu allows you to change the USB-related features. Select an item then press to display the configuration options. Enables USB host controllers. USB Configuration Module Version - 2.23.2-9.4 USB Devices Enabled: None USB Function Legacy USB Support USB 2.0 Controller USB 2.0 Controller Mode [Enabled] [Auto] [Enabled] [HiSpeed] The M o d u l e V e r s i o n and U S B D e v i c e s E n a b l e d items show the auto-detected values.
4.4.4 CPU Configuration The items in this menu show the CPU-related information that the BIOS automatically detects. Configure Advanced CPU settings Manufacturer: Intel Brand String: Genuine Intel(R) CPU 3.
Enhanced C1 Control [Auto] When set to [Auto], the BIOS automatically checks the CPU’s capability to enable the C1E support. In C1E mode, the CPU power consumption is lower when idle. Configuration options: [Auto] [Disabled] CPU Internal Thermal Control [Auto] Allows you to disable or set to auto the CPU Internal Thermal Control function. Configuration options: [Auto] [Disabled] Hyper-Threading Technology [Enabled] Allows you to enable or disable the processor Hyper-Threading Technology.
DRAM RAS# to CAS# Delay [4 Clocks] Controls the latency between the DDR SDRAM active command and the read/write command. Configuration options: [2 Clocks] [3 Clocks] [4 Clocks] [5 Clocks] DRAM RAS# Activate to Precharge Delay [15 Clocks] Configuration options: [4 Clocks] [5 Clocks] ~ [15 Clocks] DRAM Write Recovery Time [4 Clocks] Configuration options: [2 Clocks] [3 Clocks] [4 Clocks] [5 Clocks] DRAM ECC Mode [Auto] Allows you to enable or disable the ECC support for the installed DDR-2 memory modules.
4.4.
OnBoard WIFI Controller [Enabled] Allows you to enable or disable the onboard Wi-Fi controller. Configuration options: [Disabled] [Enabled] ITE8212F Controller [IDE Mode] Allows you to set the onboard ITE® 8212F IDE RAID controller operating mode. Configuration options: [RAID Mode] [IDE Mode] [Disabled] Detecting Device Time [Quick Mode] Sets the time the ITE8212F IDE RAID controller detects devices connected to the IDE RAID connectors.
4.4.7 PCI PnP The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices. Take caution when changing the settings of the PCI PnP menu items. Incorrect field values can cause the system to malfunction. Advanced PCI/PnP Settings WARNING: Setting wrong values in below sections may cause system to malfunction.
PCI IDE BusMaster [Enabled] Allows BIOS to use PCI bus mastering when reading/writing to IDE devices. Configuration options: [Disabled] [Enabled] IRQ-xx assigned to [PCI Device] When set to [PCI Device], the specific IRQ is free for use of PCI/PnP devices. When set to [Reserved], the IRQ is reserved for legacy ISA devices. Configuration options: [PCI Device] [Reserved] 4.4.
4.5 Power menu The Power menu items allow you to change the settings for the ACPI and Advanced Power Management (APM) features. Select an item then press to display the configuration options. Suspend Mode Repost Video on S3 Resume ACPI 2.0 Support ACPI APIC Support [Auto] [No] [No] [Enabled] Select the ACPI state used for System Suspend. APM Configuration Hardware Monitor 4.5.
4.5.5 APM Configuration APM Configuration Power Button Mode [On/Off] Restore on AC Power Loss Power On By RTC Alarm Power On By External Modems Power On By PCI Devices Power On By PS/2 Keyboard Keyboard Wakeup Password : Power On By PS/2 Mouse [Power Off] [Disabled] [Disabled] [Disabled] [Disabled] Not Installed [Disabled] Go into On/Off or Suspend when Power button is pressed. Power Button Mode [On/Off] Allows the system to go into On/Off mode or suspend mode when the power button is pressed.
Power On By PS/2 Keyboard [Disabled] Allows you to use specific keys on the keyboard to turn on the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Enabled] Wakeup Password This item appears only when the P o w e r O n B y P S / 2 K e y b o a r d is set to [Enabled]. Select this item, then press to set or change the keyboard wakeup password.
4.5.6 Hardware Monitor Hardware Monitor CPU Temperature MB Temperature [32.5ºC/90.5ºF] [36.0ºC/96.5ºF] CPU Fan Speed CPU Q-Fan Control Chassis Fan1 Speed Power Fan Speed [3813 RPM] [Disabled] [N/A] [N/A] VCORE Voltage 3.3V Voltage 5V Voltage 12V Voltage [ 1.320V] [ 3.345V] [ 5.094V] [11.880V] CPU Temperature [xxxºC/xxxºF] MB Temperature [xxxºC/xxxºF] The onboard hardware monitor automatically detects and displays the motherboard and CPU temperatures.
CPU Fan Ratio [Auto] Allows you to select the appropriate CPU fan speed ratio for the system. The default [Auto] automatically selects the fan speed ratio when operating a low CPU temperature. Select a higher ratio if you installed additional devices and the system requires more ventilation. Configuration options: [Auto] [90%] [80%] [70%] [60%] CPU Target Temperature [xxxºC] Allows you to set the CPU temperature threshold when the CPU fan speed is increased to lower the CPU temperature.
4.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press to display the sub-menu. APM Configuration Boot Device Priority Boot Settings Configuration Security Select Screen Select Item Enter Go to Sub-screen F1 General Help F10 Save and Exit ESC Exit 4.6.
4.6.2 Boot Settings Configuration Boot Settings Configuration Quick Boot Full Screen Logo AddOn ROM Display Mode Bootup Num-Lock PS/2 Mouse Support Wait For ‘F1’ If Error Hit ‘DEL’ Message Display Interrupt 19 Capture [Enabled] [Enabled] [Force BIOS] [On] [Auto] [Enabled] [Enabled] [Disabled] Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system.
Interrupt 19 Capture [Disabled] When set to [Enabled], this function allows the option ROMs to trap Interrupt 19. Configuration options: [Disabled] [Enabled] 4.6.3 Security The Security menu items allow you to change the system security settings. Select an item then press to display the configuration options. Security Settings Supervisor Password User Password to change password. again to disabled password.
After you have set a supervisor password, the other items appear to allow you to change other security settings.
Clear User Password Select this item to clear the user password. Password Check [Setup] When set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system. Configuration options: [Setup] [Always] Boot Sector Virus Protection [Disabled] Allows you to enable or disable the boot sector virus protection.
4.7 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items. Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Exit system setup after saving the changes. Load Setup Defaults F10 key can be used for this operation. Select Screen Select Item Enter Go to Sub-screen F1 General Help F10 Save and Exit ESC Exit Pressing does not immediately exit this menu.
Load Setup Defaults Allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press , a confirmation window appears. Select Y e s to load default values. Select E x i t & S a v e C h a n g e s or make other changes before saving the values to the non-volatile RAM.
4-44 Chapter 4: BIOS setup
This chapter describes the contents of the support CD that comes with the motherboard package.
Chapter summary 5 5.1 Installing an operating system ............................................. 5-1 5.2 Support CD information ........................................................ 5-1 5.3 IEEE 1394b driver information ............................................. 5-8 5.4 Software information ......................................................... 5-11 5.5 RAID configurations ............................................................ 5-19 5.6 Creating a RAID driver disk ..............
5.1 Installing an operating system This motherboard supports Windows® 2000/2003 Server/XP operating systems (OS). Always install the latest OS version and corresponding updates to maximize the features of your hardware. 5.2 • Motherboard settings and hardware options vary. Use the setup procedures presented in this chapter for reference only. Refer to your OS documentation for detailed information.
5.2.2 Drivers menu The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. The screen display and driver options vary under different operating system versions. QFE Update Installs the Quick Fix Engineering (QFE) driver updates. Intel Chipset Inf Update Program Installs the Intel® Chipset INF Update Program. This driver enables Plug-n-Play INF support for the Intel® chipset components on the motherboard.
Marvell Yukon Gigabit Ethernet Driver Installs the driver for the Marvell® Yukon 88E8052 PCI Express Gigabit LAN. IT8212 Driver and Application Installs the driver for the IT8212 IDE RAID controller. Make ITE8212 Driver Disk Allows you to create a driver disk for the IT8212 IDE RAID setup. See page 5-42 for details. USB 2.0 Driver Installs the USB 2.0 driver. Silicon Image RAID Driver and Utility Installs the Silicon Image 3114R RAID driver and utility.
5.2.3 Utilities menu The U t i l i t i e s menu displays the software applications and utilities that the motherboard supports. Click on an item to install. Marvell Yukon VCT Application The Virtual Cable Tester (VCT) is a cable diagnostic application that analyzes and reports LAN cable faults and shorts. See page 5-10 for details. ASUS PC Probe This smart utility monitors the fan speed, CPU temperature, and system voltages, and alerts you of any detected problems.
Anti-virus application The anti-virus application scans, identifies, and destroys computer worms and viruses attempting to damage your data. View the online help for detailed information. Winbond Voice Editor This Voice Editor application allows you to record and customize wave files for the ASUS POST Reporter™ utility. Use this program to change the default vocal POST messages. See section “3.2 Vocal POST Messages” for details. ADOBE Acrobat Reader The Adobe Acrobat® Reader V5.
5.2.5 Contact information Click the C o n t a c t tab to display the ASUS contact information. You can also find this information on the inside front cover of this user guide. 5.2.6 Other information The icons on the top right corner of the screen provide additional information on the motherboard and the contents of the support CD. Click an icon to display the specified information. Motherboard Info Displays the general specifications of the motherboard.
Browse this CD Displays the contents of the support CD in graphical format. Technical Support Form Displays the ASUS Technical Support Request Form that you have to fill out when requesting technical support. Filelist Displays the contents of the support CD in text format.
5.3 IEEE 1394b driver information You can connect your IEEE 1394b/a devices to the IEEE 1394b ports after installing the IEEE 1394b/RJ-45 ports module and the TI IEEE 1394b driver. The IEEE 1394b ports fully support most IEEE 1394b/a consumer electronic (CE) devices, except the IEEE 1394a digital video (DV) camcorders. If you wish to connect a DV camcorder to the IEEE 1394b ports, use the Microsoft 1394 stack driver.
5. Select the option Install from a list or specific location ( A d v a n c e d )), then click N e x tt. 6. Select the option Don’t search, I will choose the d r i v e r t o i n s t a l ll, then click N e x tt. 7. Select the Microsoft 1394 stack driver from the list, then click N e x tt. The Microsoft 1394 stack driver follows the IEEE 1394 OHCI host contoller. For this motherboard, the Microsoft 1394 stack driver is the Texas Instrument OHCI IEEE 1394 Host Controller.
The wizard installs the Microsoft 1394 stack driver. 8. Click F i n i s h after the wizard completes installing the driver. 9. Open the D e v i c e M a n a g e r window to verify if the Microsoft 1394 stack driver is correctly installed. Repeat the process when a question mark or an exclamation point appears before the item. After using your DV camcorder, revert to the Unibrain IEEE 1394 driver to support other IEEE 1394b/a devices.
5.4 Software information Most of the applications in the support CD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software application for more information. 5.4.1 ASUS MyLogo2™ The ASUS MyLogo2™ utility lets you customize the boot logo. The boot logo is the image that appears on screen during the Power-On-Self-Tests (POST).
7. When the logo images appear on the right window pane, select an image to enlarge by clicking on it. 8. Adjust the boot image to your desired size by selecting a value on the R a t i o box. 9. When the screen returns to the ASUS Update utility, flash the original BIOS to load the new boot logo. 10. After flashing the BIOS, restart the computer to display the new boot logo during POST.
5.4.2 AI NET2 The AI NET2 features the Marvell® Virtual Cable Tester™ (VCT). VCT is a cable diagnostic utility that reports LAN cable faults and shorts using the Time Domain Reflectometry (TDR) technology. The VCT detects and reports open and shorted cables, impedance mismatches, pair swaps, pair polarity problems, and pair skew problems of up to 64 ns at one meter accuracy. The VCT feature reduces networking and support costs through a highly manageable and controlled network system.
5.4.3 C-Media 3D audio configuration The C-Media 3D Audio Configuration utility allows easy installation and set up of audio devices through a user-friendly interface. The utility is automatically installed when you install the C-Media CMI9880 audio driver and application from the motherboard support CD. Refer to section “5.2.2 Drivers menu.” Launching the C-Media 3D Audio Configuration utility Launch the C-Media 3D Audio Configuration utility by double clicking the C-Media icon on the Windows® taskbar.
Smart Jack Setting g. You can configure the function of the rear panel, front panel, and digital I/O audio ports from this section. Click the Smart Jack setting button that corresponds to the port that you wish to configure. Mode Selection n. This section allows you to set the Speaker Tester or the Digital Signal Processing (DSP). Click the button to change the audio modes. Speaker Tester and Audio DSP Setting g. You can configure your speaker setup and the audio DSP settings in this section.
Effect The E f f e c t tab allows you to control the environment emulation, set the environment size, and adjust the equalizer settings. Environment settings Equalizer settings Environment size E n v i r o n m e n tt. This section contains various pre-programmed enviroment emulations. There are four featured materials that emulate the bathroom, concert hall, underwater, and music pub environments. Click the corresponding button to set an environment emulation.
Device Setting The D e v i c e S e t t i n g tab allows you to enable the audio CODEC multi-streaming feature, select a sound playback, and sound recording devices. Information The I n f o r m a t i o n tab displays your 3D audio engine, audio CODEC, audio driver, audio controller, and DirectX information.
Using Dolby® Digital Live Live™ The Dolby® Digital Live™ technology encodes your computer’s digital audio contents to real-time Dolby® Digital streams. Using the CODEC and the Sony/Philips Digital Interface (S/PDIF) ports on the motherboard, you can send the encoded Dolby® Digital streams to an AC-3 decoder for playback on a multi-channel speaker system. Refer to the following illustrations when converting sounds to Dolby® Digital streams.
5.5 RAID configurations The motherboard comes with the Silicon Image Sil3114, ITE 8212, and the Intel® ICH6R Southbride RAID controllers that allow you to configure IDE and Serial ATA hard disk drives as RAID sets. The motherboard supports the following RAID configurations. R A I D 0 (Data striping) optimizes two identical hard disk drives to read and write data in parallel, interleaved stacks.
I n t e l® M a t r i x S t o r a g e e. The Intel® Matrix Storage technology supported by the ICH6R chip allows you to create a RAID 0 and a RAID 1 set using only two identical hard disk drives. The Intel® Matrix Storage technology creates two partitions on each hard disk drive to create a virtual RAID 0 and RAID 1 sets. This technology also allows you to change the hard disk drive partition size without losing any data.
5.5.2 Silicon Image RAID configurations The Silicon Image RAID controller supports RAID 0, RAID 1, RAID 10, and RAID 5 configurations. Use the Silicon Image RAID utility to configure a disk array. Setting the BIOS RAID items After installing the hard disk drives, make sure to set the necessary RAID items in the BIOS before setting your RAID configuration. To set the BIOS RAID items: 1. 2. Boot the system and press during the Power-On Self-Test (POST) to enter the BIOS Setup Utility.
Entering the Silicon Image BIOS RAID Configuration Utility To enter the Silicon Image BIOS RAID configuration utility: 1. Boot up your computer. 2. During POST, press or . The RAID BIOS setup screens shown in this section are for reference only, and may not exactly match the items on your screen. RAID Configuration Utility - Silicon Image Inc.
Creating a RAID 0 set (Striped) To create a RAID set: 1. From the Silicon Image configuration utility main menu, select C r e a t e R A I D s e t then press to display an option menu. MAIN MENU Create RAID set Delete RAID set Rebuild Raid1 set Resolve Conflicts Low Level Format Logical Drive Info 2. RAID0 RAID1 RAID5 RAID10 SPARE DRIVE JBOD Select R A I D 0 then press to display the following. MAIN MENU Auto configuration Manual configuration 3.
T I P : For server systems, use of a lower array block size is recommended. For multimedia computer systems used mainly for audio and video editing, a higher array block size is recommended for optimum performance. b. Use the up or down arrow keys to select a chunk size appropriate to your drive usage, then press . The selection bar moves to the Physical Drive menu. PHYSICAL DRIVE 0 1 2 3 XXXXXXXXXXX XXXXXXXXXXX XXXXXXXXXXX XXXXXXXXXXX XXXXXXMB XXXXXXMB XXXXXXMB XXXXXXMB c.
3. Select your desired method of configuration. Auto configuration a. Select Auto Configuration then press . b. The utility prompts a confirmation message. Press to confirm or to return to the configuration Main Menu. • Auto-configuration creates a RAID 1 set without backup copy. • When migrating a single hard disk drive to a RAID 1 set, use of the Manual configuration is recommended. Manual configuration a. Select M a n u a l configuration n, then press .
e. If you selected C r e a t e w i t h d a t a c o p y y, the following pop-up menu appears. MAIN MENU Auto configuration Manual configuration online copy offline copy The o n l i n e c o p y option automatically copies the data to the target drives on the background while writing to the source drives. The o f f l i n e c o p y option allows you to copy the contents of the source drive to the target drives now. f. Use the up or down arrow keys to select desired copy method, then press . g.
3. Select your desired method of configuration. Auto configuration a. Select Auto Configuration then press . b. The utility prompts a message to input the RAID size, use the up or down arrow keys to set the RAID size then press . c. Press to confirm or to return to the Main Menu. Manual configuration a. Select M a n u a l c o n f i g u r a t i o n and press . The following pop-up menu appears. MAIN MENU Auto configuration Manual configuration b.
Creating a RAID 10 set (Mirrored + Striped) To create a RAID 10 set: 1. From the Silicon Image configuration utility main menu, select C r e a t e R A I D s e t then press . The following sub-menu appears. To create a RAID 10 set: MAIN MENU Create RAID set Delete RAID set Rebuild Raid1 set Resolve Conflicts Low Level Format Logical Drive Info 2. RAID0 RAID1 RAID10 RAID5 SPARE DRIVE RAID10 SPARE DRIVE JBOD Select R A I D 1 0 then press to display the following.
Manual configuration a. Select M a n u a l c o n f i g u r a t i o n and press . The following pop-up menu appears. MAIN MENU Auto configuration Manual configuration chunk size 4K 8K 16K 32K 64K 128K T I P : For server systems, use of a lower array block size is recommended. For multimedia computer systems used mainly for audio and video editing, a higher array block size is recommended for optimum performance. b.
e. After setting the RAID drives, the following pop-up menu appears. MAIN MENU Auto configuration Manual configuration Create with data copy Create without data copy • The C r e a t e w i t h d a t a c o p y option allows you to copy the current data from the source drive to the mirror drive. The C r e a t e w i t h o u t d a t a c o p y option disables the disk copy function of the Mirrored set.
5.5.3 Intel® RAID configurations This motherboard supports RAID 0, RAID 1, and Intel® Matrix Storage configurations for Serial ATA hard disks drives through the Intel® ICH6R chipset. Use the Intel® Application Accelerator RAID Option ROM utility to configure a disk array. Setting the BIOS RAID items After installing the hard disk drives, make sure to set the necessary RAID items in the BIOS before setting your RAID configuration. To set the BIOS RAID items: 1. 3.
At the bottom of the screen are the navigation keys. These keys allow you to move through and select menu options. [ ]-Change [TAB]-Next [ESC] Previous Menu [Enter]-Select Creating a RAID Volume To create a RAID volume: 1. From the Intel Application Accelerator RAID Option ROM utility main 1. Create RAID Volume menu, select [1 e] then press . The following screen appears. Intel(R) Application Accelerator RAID Option ROM v4.0.0.6211 Copyright(C) 2003-04 Intel Corporation. All Rights Reserved.
T I P : For server systems, use of a lower array block size is recommended. For multimedia computer systems used mainly for audio and video editing, a higher array block size is recommended for optimum performance. b. If you selected RAID (MIrrored), the Create Volume prompt appears. 4. On the Create Volume prompt, press to create the array. The utility prompts a confirmation message, press . WARNING: ALL DATA ON SELECTED DISK WILL BE LOST.
2. Press to delete the RAID volume. The following confirmation message appears. [ VOLUME DELETE VERIFICATION ] ALL DATA IN THE VOLUME WILL BE LOST!! Are you sure you want to delete volume "RAID_Volume0"? (Y/N) 3. Press to confirm or to return to the configuration Main Menu. Resetting RAID Disks Drives Take caution when resetting a RAID to non-RAID. Resetting all RAID data will remove any internal RAID structure from all RAID disks! 1. 3.
5.5.4 ITE® 8212F RAID configurations The ITE® 8212F IDE RAID controller supports RAID 0, RAID 1, RAID 0+1 and JBOD configurations. Use the IT8212 BIOS Setup Utility or the ATA RAID Manager application to configure a disk array. Setting the BIOS RAID items After installing the hard disk drives, make sure to set the necessary RAID items in the BIOS before setting your RAID configuration. To set the BIOS RAID items: 1. 2. 3.
3. At the bottom of the screen are the navigation keys. These keys allow you to move through and select from the menu options. [1]..[5] Select 4. [ESC] Exit Press the number of your selection or to exit. Auto-configuring a RAID array This option allows you to select a supported RAID set for the utility to automatically configure. To auto-configure a RAID set: 1. From the IT8212 Setup Utility screen, press <1>. The following screen appears. IT8212 Setup Utility (C)Copyright 2002-2004 ITE, Inc.
Defining a RAID array This option allows you to define supported RAID arrays. To define a RAID array: 1. From the IT8212 Setup Utility screen, press <2>. The following screen appears. IT8212 Setup Utility (C)Copyright 2002-2004 ITE, Inc. [ Define RAID Menu ] Array No Array Mode Drive No Size(MB) Status Array 0 ---- ---- ----- ----- Array 1 ---- ---- ----- ----- Array 2 ---- ---- ----- ----- Array 3 ---- ---- ----- ----- ∗ : Capacity (GB) ↑] Up ↓] Down [↑ [↓ 2.
3. Use the up or down arrow keys to select editable fields. 4. Use the Space bar to change field values. 5. Press to save RAID array. 6. Press to exit. Deleting a RAID array This option allows you to delete an existing RAID array. To delete a RAID array: 1. From the IT8212 Setup Utility screen, press <3>. The following screen appears. IT8212 Setup Utility (C)Copyright 2002-2004 ITE, Inc.
Rebuilding a RAID array This option allows you to reconstruct an existing RAID array. This option applies only to RAID1 (Mirrored) or RAID 0+1(Striped+Mirrored) sets. To rebuild a RAID array: 1. From the IT8212 Setup Utility screen, press <4>. The following screen appears. IT8212 Setup Utility (C)Copyright 2002-2004 ITE, Inc.
3. Use the up or down arrow keys to select a drive, then press . Follow succeeding screen instructions. 4. Press to exit. Viewing your RAID configuration This option allows you to view your RAID configuration. You can also enable or disable the Auto-rebuild function in this section. To view your RAID configuration: 1. From the IT8212 Setup Utility screen, press <5>. The following screen appears. IT8212 Setup Utility (C)Copyright 2002-2004 ITE, Inc.
5.6 Creating a RAID driver disk A floppy disk with the RAID driver is required when installing Windows® 2000/XP operating system on a hard disk drive that is included in a RAID set. You can create a RAID driver disk in DOS (using the Makedisk application in the support CD) or in Windows environment. To create a RAID driver disk from DOS environment: 1. Place the motherboard support CD in the optical drive. 2. Restart the computer, then enter the BIOS Setup. 3.
To create a RAID driver disk from Windows® environment: 1. 2. Place the motherboard support CD in the optical drive. When the D r i v e r s menu appears, select the RAID driver disk you wish to create: • Click M a k e I T E 8 2 1 2 D r i v e r D i s k to create an ITE® 8212F RAID driver disk.