Motherboard P5E3 Deluxe
E3366 First Edition V1 September 2007 Copyright © 2007 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Notices........................................................................................................ viii Safety information....................................................................................... ix About this guide........................................................................................... x P5E3 Deluxe specifications summary...................................................... xii Chapter 1: Product introduction 1.1 Welcome!..........................
Contents 2.5.5 PCI Express x1 slots...................................................... 2-19 2.5.6 PCI Express 2.0 x16 slots.............................................. 2-19 2.5.7 AI Slot Detector.............................................................. 2-20 2.6 Jumper......................................................................................... 2-21 2.7 Connectors.................................................................................. 2-22 2.7.
Contents 4.4 4.5 4.6 4.7 4.3.5 SATA 1-6........................................................................ 4-12 4.3.6 SATA Configuration........................................................ 4-13 4.3.7 AHCI Configuration........................................................ 4-14 4.3.8 System Information........................................................ 4-15 Ai Tweaker menu......................................................................... 4-16 4.4.1 Ai Overclock Tuner.....
Contents 4.8 4.9 Tools menu.................................................................................. 4-37 4.8.1 ASUS EZ Flash 2........................................................... 4-37 4.8.2 ASUS O.C. Profile.......................................................... 4-38 4.8.3 Ai Net 2.......................................................................... 4-39 Exit menu..................................................................................... 4-40 Chapter 5: 5.
Chapter 6: 6.1 ATI® CrossFire™ technology support Overview........................................................................................ 6-1 6.1.1 Requirements................................................................... 6-1 6.1.2 Before you begin.............................................................. 6-1 6.2 Installing CrossFire™ graphics cards........................................ 6-2 6.3 Software information................................................................
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This guide contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports. • Chapter 2: Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components.
Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Instructions that you MUST follow to complete a task. NOTE: Tips and additional information to help you complete a task.
P5E3 Deluxe specifications summary CPU LGA775 socket for Intel® Core™2 Quad / Core™2 Extreme / Core™2 Duo / Pentium® Extreme / Pentium® D / Pentium® 4 Processors Compatible with Intel® 05B/05A/06 processors Intel® next generation 45nm Multi-Core CPU * Refer to www.asus.com for Intel CPU support list Chipset Intel® X38 / ICH9R with Intel® Fast Memory Access Technology System Bus 1600 / 1333 / 1066 / 800 MHz Memory 4 x DIMM, max.
P5E3 Deluxe specifications summary ASUS AI Lifestyle Unique features ASUS Power Saving Solution: - ASUS EPU (Energy Processing Unit) - ASUS AI Gear 3 (ASUS EPU Utility) - ASUS AI Nap ASUS AI Life Features: - ASUS AI Direct Llink ASUS Quiet Thermal Solution: - ASUS 8-Phase Power Design - ASUS Fanless Design: Heat-pipe solution - ASUS Fanless Design: StackCool 2 - ASUS Q-Fan 2 - ASUS Optional Fan for Water-cooling or PassiveCooling only ASUS EZ DIY: - ASUS Q-Shield - ASUS Q-Connector - ASUS O.C.
P5E3 Deluxe specifications summary Back Panel I/O Ports 1 x PS/2 Keyboard 1 x S/PDIF Out (Coaxial + Optical) 2 x External SATA 1 x IEEE1394a 2 x RJ45 ports 6 x USB 2.0/1.
This chapter describes the motherboard features and the new technologies it supports.
Chapter summary 1 1.1 Welcome!....................................................................................... 1-1 1.2 Package contents.......................................................................... 1-1 1.3 Special features.............................................................................
1.1 Welcome! Thank you for buying an ASUS® P5E3 Deluxe motherboard! The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your motherboard package for the following items.
1.3 Special features 1.3.1 Product highlights Green ASUS This motherboard and its packaging comply with the European Union’s Restriction on the use of Hazardous Substances (RoHS). This is in line with the ASUS vision of creating environment-friendly and recyclable products/packagings to safeguard consumers’ health while minimizing the impact on the environment. Intel® Core™ 2 Quad Processor Ready This motherboard supports the latest Intel® Core™ 2 Quad processors in the LGA775 package.
PCIe 2.0 This motherboard supports the latest PCIe 2.0 device for twice the current speed and bandwidth. This enhances system performance while still providing backward compatibility to PCIe 1.0 devices. Serial ATA 3 Gb/s technology and SATA-On-The-Go This motherboard supports hard drives based on the Serial ATA (SATA) 3 Gb/s storage specification, delivering enhanced scalability and doubling the bus bandwidth for high-speed data retrieval and saves.
High Definition Audio Enjoy high-end sound quality on your PC! The onboard 8-channel HD audio (High Definition Audio, previously codenamed Azalia) CODEC enables high-quality 192KHz/24-bit audio output that simultaneously sends different audio streams to different destinations. You can now talk to your partners on the headphone while playing multi-channel network games. See pages 2-22 and 2-23 for details. 1.3.
Fanless Design - Stack Cool 2 ASUS Stack Cool 2 is a fan-less and zero-noise cooling solution that lowers the temperature of critical heat generating components. The motherboard uses a special design on the printed circuit board (PCB) to dissipate heat these critical components generate.
Noise Filter This feature detects repetitive and stationary noises (non-voice signals) like computer fans, air conditioners, and other background noises then eliminates it in the incoming audio stream while recording. See page 5-29 for details. ASUS EZ DIY ASUS EZ DIY feature collection provides you easy ways to install computer components, update the BIOS or back up your favorite settings.
ASUS EZ Flash 2 EZ Flash 2 is a user-friendly BIOS update utility. Simply press the predefined hotkey to launch the utility and update the BIOS without entering the OS. Update your BIOS easily without preparing a bootable diskette or using an OS-based flash utility. See pages 4-4 and 4-37 for details. ASUS AI Slot Detector When PCIE/PCI devices are installed, you can find out if they are installed successfully via ASUS’s innovatively designed on-board LEDs when they switch on the power.
1- Chapter 1: Product Introduction
This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
Chapter summary 2 2.1 Before you proceed...................................................................... 2-1 2.2 Motherboard overview.................................................................. 2-2 2.3 Central Processing Unit (CPU).................................................... 2-6 2.4 System memory.......................................................................... 2-13 2.5 Expansion slots........................................................................... 2-17 2.
2.1 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity. • Hold components by the edges to avoid touching the ICs on them.
2.2 Motherboard overview Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components. 2.2.1 Placement direction When installing the motherboard, make sure that you place it into the chassis in the correct orientation.
2.2.3 Motherboard layout 24.5cm (9.6in) CHASSIS CPU_FAN KB_USB56 EATX12V Super I/O PWR_FAN SPDIF_O12 EPU LGA775 FLOPPY EATXPWR CHA_FAN2 DET_PCI1 PCI1 P5E3 DELUXE SATA34 DET_X16_1 SATA56 PCIEX16_1 DET_X1_2 Intel® ICH9R PCIEX1_2 CD DET_X16_2 PRI_EIDE AD1988B PCIEX16_2 DET_PCI2 USB910 PCI2 JMB363 agere ASM 8283 PCIEX16_3 COM1 AAFP BIOS L-FW3227-100 CR2032 3V Lithium Cell CMOS Power DET_X16_3 SPDIF_OUT 30.5cm (12.
2.2.4 Layout contents Slots Page 1. DDR3 DIMM slots 2-13 2. PCI slots 2-19 3. PCI Express x 1 slots 2-19 4. PCI Express x16 slots 2-19 Jumper 1. 2- Page Clear RTC RAM (3-pin CLRTC) 2-21 Rear panel connectors Page 1. PS/2 keyboard port (purple) 2-22 2. Coaxial S/PDIF Out port 2-22 3. LAN 1 (RJ-45) port 2-22 4. IEEE 1394a port 2-22 5. LAN 2 (RJ-45) port 2-22 6. Center/Subwoofer port (orange) 2-22 7. Rear Speaker Out port (black) 2-22 8.
Internal connectors Page 1. Floppy disk drive connector (34-1 pin FLOPPY) 2-25 2. IDE connector (40-1 pin PRI_EIDE)) 2-26 3. ICH9R Serial ATA connectors (7-pin SATA1-6) 2-27 4. USB connectors (10-1 pin USB78, USB910, USB1112) 2-28 5. IEEE 1394a port connector (10-1 pin IE1394_2) 2-29 6. CPU, chassis and power fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN1-4, 3-pin PWR_FAN) 2-30 7. Chassis intrusion connector (4-1 pin CHASSIS) 2-31 8.
2.3 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA775 socket designed for the Intel® Core™2 Quad / Core™2 Extreme / Core™2 Duo / Pentium® Extreme / Pentium® D / Pentium® 4 Processors. 2- • Make sure that all power cables are unplugged before installing the CPU. • If installing a dual-core CPU, connect the chassis fan cable to the CHA_FAN1 connector to ensure system stability. • Due to the chipset limitation, we recommend you use FSB 800MHz CPU or above.
2.3.1 Installing the CPU To install a CPU: Locate the CPU socket on the motherboard. ® 1. P5E3 DELUXE P5E3 DELUXE CPU Socket 775 Before installing the CPU, make sure that the cam box is facing towards you and the load lever is on your left. 2. Press the load lever with your thumb (A), then move it to the left (B) until it is released from the retention tab. Retention tab A PnP cap Load lever B This side of the socket box should face you.
4. Lift the load plate with your thumb and forefinger to a 100º angle (A), then push the PnP cap from the load plate window to remove (B). B A Load plate Alignment key 5. Position the CPU over the socket, making sure that the gold triangle is on the bottom‑left corner of the socket then fit the socket alignment key into the CPU notch. CPU notch Gold triangle mark The CPU fits in only one correct orientation.
2.3.2 Installing the CPU heatsink and fan ® The Intel LGA775 processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. • When you buy a boxed Intel® processor, the package includes the CPU fan and heatsink assembly. If you buy a CPU separately, make sure that you use only Intel®‑certified multi‑directional heatsink and fan. • Your Intel® LGA775 heatsink and fan assembly comes in a push-pin design and requires no tool to install.
2. Push down two fasteners at a time in a diagonal sequence to secure the heatsink and fan assembly in place. B A A 3. A B B A B Connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN. GND CPU FAN PWR CPU FAN IN CPU FAN PWM ® CPU_FAN P5E3 DELUXE P5E3 DELUXE CPU fan connector DO NOT forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector.
2.3.3 Uninstalling the CPU heatsink and fan To uninstall the CPU heatsink and fan: 1. Disconnect the CPU fan cable from the connector on the motherboard. 2. Rotate each fastener counterclockwise. 3. Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and fan assembly from the motherboard. 4. A B B A B A A B Carefully remove the heatsink and fan assembly from the motherboard.
5. Rotate each fastener clockwise to ensure correct orientation when reinstalling. Narrow end of the groove The narrow end of the groove should point outward after resetting. (The photo shows the groove shaded for emphasis.) Refer to the documentation in the boxed or stand-alone CPU fan package for detailed information on CPU fan installation.
2.4 System memory 2.4.1 Overview The motherboard comes with four Double Data Rate 3 (DDR3) Dual Inline Memory Modules (DIMM) sockets. A DDR3 module has the same physical dimensions as a DDR2 DIMM but is notched differently to prevent installation on a DDR2 DIMM socket. DDR3 modules are developed for better performance with less power consumption. DIMM_B1 DIMM_B2 ® DIMM_A1 DIMM_A2 The figure illustrates the location of the DDR3 DIMM sockets: P5E3 DELUXE P5E3 DELUXE 240-pin DDR3 DIMM sockets 2.4.
• You may install varying memory sizes in Channel A and Channel B. The system maps the total size of the lower-sized channel for the dual-channel configuration. Any excess memory from the higher-sized channel is then mapped for single-channel operation. • Always install DIMMs with the same CAS latency. For optimum compatibility, it is recommended that you obtain memory modules from the same vendor.
P5E3 Deluxe Motherboard Qualified Vendors Lists (QVL) DDR3-1066MHz capability DIMM socket support (Optional) Size Vendor Chip No. CL SS/ Part No.
2.4.3 Installing a DIMM Unplug the power supply before adding or removing DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components. 2 To install a DIMM: 1. Unlock a DIMM socket by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. 3. Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated.
2.5 Expansion slots In the future, you may need to install expansion cards. The following sub‑sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. 2.5.1 Installing an expansion card To install an expansion card: 1.
2.5.
2.5.4 PCI slots The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. Refer to the figure below for the location of the slot. 2.5.5 PCI Express x1 slots This motherboard supports PCI Express x1 network cards, SCSI cards and other cards that comply with the PCI Express specifications. Refer to the figure below for the location of the slot. 2.5.6 PCI Express 2.
Primary PCI Express x16 slots The primary PCI Express x16 slots support PCI Express x16 graphic cards that comply with the PCI Express specifications. Universal PCI Express slot (max. x4 mode) This motherboard also supports a Universal PCI Express slot with a maximum speed of 2 GB/s. The operating frequency of this slot changes, depending on the type of PCI Express card you install. Refer to the table below for details.
2.6 1. Jumper Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the onboard battery. 3. Move the jumper cap from pins 1-2 (default) to pins 2-3.
2.7 Connectors 2.7.1 Rear panel connectors 1 16 3 2 15 4 14 13 5 12 6 7 8 9 11 10 1. PS/2 keyboard port (purple). This port is for a PS/2 keyboard. 2. Coaxial S/PDIF Out port. This port connects an external audio output device via a coaxial S/PDIF cable. 3. LAN 1 (RJ-45) port. Supported by Marvell® LAN controller, this port allows Gigabit connection to a Local Area Network (LAN) through a network hub. Refer to the table below for the LAN port LED indications. 4. IEEE 1394a port.
10. Microphone port (pink). This port connects a microphone. 11. Side Speaker Out port (gray). This port connects the side speakers in an 8-channel audio configuration. Refer to the audio configuration table below for the function of the audio ports in 2, 4, 6, or 8-channel configuration.
• Before creating a RAID set using Serial ATA hard disks, make sure that you have connected the Serial ATA signal cable and installed Serial ATA hard disk drives; otherwise, you cannot enter the JMicron RAID utility and SATA BIOS setup during POST. • If you intend to create a RAID configuration using this connector, set the J-Micron eSATA/PATA Controller Mode in the BIOS to [RAID]. See section 4.5.3 Onboard Device Configuration for details.
2.7.2 1. Internal connectors Floppy disk drive connector (34-1 pin FLOPPY) ® This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. FLOPPY NOTE: Orient the red markings on the floppy ribbon cable to PIN 1.
2. IDE connector (40-1 pin PRI_E IDE) ® The onboard IDE connector is for the Ultra DMA 133/100 signal cable. There are three connectors on each Ultra DMA 133/100 signal cable: blue, black, and gray. Connect the blue connector to the motherboard’s IDE connector, then select one of the following modes to configure your device. PRI_EIDE NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1.
3. ICH9R Serial ATA connectors (7-pin SATA1-6) These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives and optical disc drives. If you installed Serial ATA hard disk drives, you can create a RAID 0, 1, 5, and 10 configuration with the Intel® Matrix Storage Technology through the onboard Intel® ICH9R RAID controller.
4. USB connectors (10-1 pin USB 78, USB 910, USB 1112) USB910 USB1112 USB78 USB+5V USB_P8USB_P8+ GND NC USB+5V USB_P12USB_P12+ GND NC P5E3 DELUXE USB 2.0 connectors USB+5V USB_P7USB_P7+ GND USB+5V USB_P11USB_P11+ GND USB+5V USB_P10USB_P10+ GND NC P5E3 DELUXE USB+5V USB_P9USB_P9+ GND ® These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.
5. IEEE 1394a port connector (10-1 pin IE1394_2) +12V TPB1+ GND TPA1+ ® This connector is for a IEEE 1394a port. Connect the IEEE 1394a module cable to this connector, then install the module to a slot opening at the back of the system chassis. P5E3 DELUXE P5E3 DELUXE IEEE 1394a connector PIN 1 GND +12V TPB1GND TPA1- IE1394_2 Never connect a USB cable to the IEEE 1394a connector.
6. CPU, chassis and power fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN1-4, 3-pin PWR_FAN) The fan connectors support cooling fans of 350 mA ~ 2000 mA (24 W max.) or a total of 1 A ~ 7 A (84 W max.) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector.
7. Chassis intrusion connector (4-1 pin CHASSIS) This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. The signal is then generated as a chassis intrusion event. By default , the pin labeled “Chassis Signal” and “Ground” are shorted with a jumper cap.
8. ATX power connectors (24-pin EATXPWR, 2x4-pin EATX12V) These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit.
9. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector.
10. Optical drive audio connector (4-pin CD) ® This connector allows you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner, or MPEG card. (black) CD P5E3 DELUXE Left Audio Channel Ground Ground Right Audio Channel P5E3 DELUXE Internal audio connector 11. Digital audio connector (4-1 pin SPDIF, for ASUS HDMI VGA card) ® This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port(s).
12. System panel connector (20-8 pin PANEL) This connector supports several chassis-mounted functions. SPEAKER +5V Ground Ground Speaker PLED- ® PLED+ PLED P5E3 DELUXE IDE_LED Reset Ground PWR Ground IDE_LED+ IDE_LED- PANEL RESET PWRSW * Requires an ATX power supply. P5E3 DELUXE System panel connector • System power LED (2-pin PLED) This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector.
ASUS Q-Connector (system panel) You can use the ASUS Q-Connector to connect/disconnect chassis front panel cables in a few steps. Refer to the instructions below to install the ASUS QConnector. 1. Connect the front panel cables to the ASUS Q-Connector. Refer to the labels on the Q-Connector to know the detailed pin definitions, then match them to the respective front panel cable labels. 2-36 2.
2.7.3 Installing the optional fans Install the optional fan only if you are using a passive cooler or a water cooler. Installing the optional fan with an active CPU cooler will interfere with the airflow and destabilize the system. 1. Position the fan above the pipe and heatsink assembly. 2. Fit the fan to the grooved edge of the heatsink. 3. Carefully push down the fan until it snugly fits the heatsink, then connect the fan cable. 4. The photo shows the fan installed on the motherboard.
2-38 5. Follow the previous instructions to install the other optional fan. 6. The photo on the right shows the fans installed on the motherboard. • Plug the optional fan cables to the CHA_FAN1, CHA_FAN2 or PWR_FAN connector on the motherboard. • Make sure the optional fan is installed correctly to prevent damage to the fan and motherboard components.
This chapter describes the power up sequence, the vocal POST messages, and ways of shutting down the system.
Chapter summary 3 3.1 Starting up for the first time......................................................... 3-1 3.2 Turning off the computer..............................................................
3.1 Starting up for the first time 1. After making all the connections, replace the system case cover. 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: 6. a. Monitor b. External SCSI devices (starting with the last device on the chain) c.
3.2 Turning off the computer 3.2.1 Using the OS shut down function If you are using Windows® XP: 1. Click the Start button then select Turn Off Computer. 2. Click the Turn Off button to shut down the computer. 3. The power supply should turn off after Windows® shuts down. If you are using Windows® Vista: 1. 2. Click the Start button then select ShutDown. The power supply should turn off after Windows® shuts down. 3.2.
This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
Chapter summary 4 4.1 Managing and updating your BIOS............................................. 4-1 4.2 BIOS setup program..................................................................... 4-8 4.3 Main menu................................................................................... 4-11 4.4 Ai Tweaker................................................................................... 4-16 4.5 Advanced menu..........................................................................
4.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. ASUS Update (Updates the BIOS in Windows® environment.) 2. ASUS EZ Flash 2 (Updates the BIOS using a floppy disk or USB flash disk.) 3. ASUS AFUDOS (Updates the BIOS using a bootable floppy disk) 4.
Quit all Windows® applications before you update the BIOS using this utility. Updating the BIOS through the Internet To update the BIOS through the Internet: 4- 1. Launch the ASUS Update utility from the Windows® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate. The ASUS Update main window appears. 2. Select Update BIOS from the Internet option from the drop‑down menu, then click Next. 3. Select the ASUS FTP site nearest you to avoid network traffic, or click Auto Select.
4. From the FTP site, select the BIOS version that you wish to download. Click Next. 5. Follow the screen instructions to complete the update process. The ASUS Update utility is capable of updating itself through the Internet. Always update the utility to avail all its features. Updating the BIOS through a BIOS file To update the BIOS through a BIOS file: 1. Launch the ASUS Update utility from the Windows® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate.
4.1.2 ASUS EZ Flash 2 utility The ASUS EZ Flash 2 feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS‑based utility. The EZ Flash 2 utility is built-in the BIOS chip so it is accessible by pressing + during the Power-On Self Tests (POST). To update the BIOS using EZ Flash 2: 1. Visit the ASUS website (www.asus.com) to download the latest BIOS file for the motherboard. 2.
4.1.3 AFUDOS utility The AFUDOS utility allows you to update the BIOS file in DOS environment using a bootable floppy disk with the updated BIOS file. This utility also allows you to copy the current BIOS file that you can use as backup when the BIOS fails or gets corrupted during the updating process. Copying the current BIOS To copy the current BIOS file using the AFUDOS utility: • Make sure that the floppy disk is not write-protected and has at least 1024KB free space to save the file.
Write the BIOS filename on a piece of paper. You need to type the exact BIOS filename at the DOS prompt. 2. Copy the AFUDOS utility (afudos.exe) from the motherboard support DVD to the bootable floppy disk you created earlier. 3. Boot the system in DOS mode, then at the prompt type: afudos /i[filename] where [filename] is the latest or the original BIOS file on the bootable floppy disk. A:\>afudos /iP5E3D.ROM 4. The utility verifies the file and starts updating the BIOS. A:\>afudos /iP5E3D.
4.1.4 ASUS CrashFree BIOS 3 utility The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can update a corrupted BIOS file using the motherboard support DVD, the floppy disk, or the USB flash disk that contains the updated BIOS file. Prepare the motherboard support DVD, the floppy disk or the USB flash disk containing the updated motherboard BIOS before using this utility.
4.2 BIOS setup program This motherboard supports a programmable Serial Peripheral Interface (SPI) chip that you can update using the provided utility described in section 4.1 Managing and updating your BIOS. Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup.” This section explains how to configure your system using this utility.
4.2.1 BIOS menu screen Menu items Main Menu bar Ai Tweaker Configuration fields BIOS SETUP UTILITY Advanced Power Boot System Time System Date Legacy Diskette A Language SATA1 SATA2 SATA3 SATA4 SATA5 SATA6 General help Tools [10:55:25] [Mon 07/23/2007] [1.44M, 3.5 in.] [English] [Not [Not [Not [Not [Not [Not Detected] Detected] Detected] Detected] Detected] Detected] SATA Configuration System Information Exit Use [ENTER], [TAB] or [SHIFT-TAB] to select a field.
4.2.4 Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting Main shows the Main menu items. The other items (Advanced, Power, Boot, and Exit) on the menu bar have their respective menu items. 4.2.5 System Time System Date Floppy Diskette A Language Use [ENTER], [TAB], or [SHIFT-TAB] to select a field. [06:22:54] [Mon 04/23/2007] [1.44M, 3.5 in.
4.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information. Refer to section 4.2.1 BIOS menu screen for information on the menu screen items and how to navigate through them. Main Ai Tweaker BIOS SETUP UTILITY Advanced Power Boot System Time System Date Legacy Diskette A Language SATA1 SATA2 SATA3 SATA4 SATA5 SATA6 [10:55:25] [Mon 04/23/2007] [1.44M, 3.5 in.
4.3.5 SATA 1-6 While entering Setup, the BIOS automatically detects the presence of Serial ATA devices. There is a separate sub-menu for each SATA device. Select a device item then press to display the SATA device information. BIOS SETUP UTILITY Main SATA 1 Device : Hard Disk Vendor : WDC WD800JD-00LSA0 Size : 80.
DMA Mode [Auto] Selects the DMA mode. Configuration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] SMART Monitoring [Auto] Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled] 32Bit Data Transfer [Enabled] Enables or disables 32-bit data transfer. Configuration options: [Disabled] [Enabled] 4.3.
Hard Disk Write Protect [Disabled] Disables or enables device write protection. This will be effective only if the device is accessed through BIOS. Configuration option: [Disabled] [Enabled] SATA Detect Time Out (Sec) [35] Selects the time out value for detecting ATA/ATAPI devices. Configuration options: [0] [5] [10] [15] [20] [25] [30] [35] 4.3.7 AHCI Configuration This menu is the section for AHCI configuration.
4.3.8 System Information This menu gives you an overview of the general system specifications. The BIOS automatically detects the items in this menu. BIOS SETUP UTILITY Main ASUS BIOS Version : 0124 Build Date : 08/12/07 Processor Type Speed Count : Genuine Intel(R) CPU 3.20GHz :3200 MHz : 1 System Memory Available : 512 MB F1 F10 ESC Select Screen Select Item General Help Save and Exit Exit v02.61 (C)Copyright 1985-2007, American Megatrends, Inc.
4.4 Ai Tweaker menu The Ai Tweaker menu items allow you to configure overclocking-related items. Take caution when changing the settings of the Ai Tweaker menu items. Incorrect field values can cause the system to malfunction. Main Ai Tweaker BIOS SETUP UTILITY Power Boot Ai Overclock Tuner [Auto] CPU Ratio Control [Auto] FSB Strap to North Bridge [Auto] DRAM Frequency [Auto] DRAM Command Rate [Auto] DRAM Timing Control [Auto] Pri. Information : 6-6-6-15-4-36-6-4 Sec.
4.4.2 CPU Ratio Control [Auto] Configuration options: [Auto] [Manual]. Ratio CMOS Setting [9] This sub-item appears only when you set the CPU Ratio Control item to [Manual]. Allows you to set the ratio between CPU Core Clock and FSB Frequency. Use the <+> and <-> keys to adjust the ratio. If an invalid ratio is set in CMOS, then actual and setpoint values may differ. 4.4.
4.4.4 DRAM Frequency [Auto] Allows you to set the DDR3 operating frequency. Configuration options: [Auto] [DDR3-800 MHz] [DDR3-835MHz] [DDR3-1002MHz] [DDR3-1066MHz] [DDR3-1111] [DDR3-1333] The DRAM Frequency configuration options vary with the FSB Frequency settings. Selecting a very high DRAM frequency may cause the system to become unstable! If this happens, revert to the default setting. 4.4.5 DRAM Command Rate [Auto] Configuration options: [Auto] [1T] [2T] 4.4.
Row Refresh Cycle Time [Auto] Configuration options: [Auto] [30 DRAM Clocks] [36 DRAM Clocks] [48 DRAM Clocks] [60 DRAM Clocks] [72 DRAM Clocks] Write Recovery Time [Auto] Configuration options: [Auto] [1 DRAM Clocks]~[15 DRAM Clocks] Read to Precharge Time [Auto] Configuration options: [Auto] [1 DRAM Clocks]~[15 DRAM Clocks] Sec.
4.4.10 Ai Clock Skew for Channel A [Auto] Configuration options: [Auto] [Advance 350ps] [Advance 300ps] [Advance 250ps] [Advance 200ps] [Advance 150ps] [Advance 100ps] [Advance 50ps] [Normal] [Delay 50ps] [Delay 100ps] [Delay 150ps] [Delay 200ps] [Delay 250ps] [Delay 300ps] [Delay 350ps] 4.4.
CPU PLL Voltage [Auto] Allows you to set the CPU PLL voltage. The values range from 1.50V to 2.78V with a 0.02V interval. FSB Termination Voltage [Auto] Allows you to set the front side bus termination voltage. The values range from 1.20V to 1.50V with a 0.02V interval. DRAM Voltage [Auto] Allows you to set the DRAM voltage. The values range from 1.50V to 2.78V with a 0.02V interval. North Bridge Voltage [Auto] Allows you to set the North Bridge voltage. The values range from 1.25V to 1.91V with a 0.
The following three items appear when you set the Ai Overclock Tuner item to [Manual] and [X.M.P.]. CPU Voltage Damper [Auto] Allows you to enable or disable the CPU voltage damper. Configuration options: [Auto] [Disabled] [Enabled] CPU Voltage Reference [Auto] Configuration options: [Auto] [0.63x] [0.61x] [0.59x] [0.57x] North Bridge Voltage Reference [Auto] Configuration options: [Auto] [0.67x] [0.61x] 4.4.
4.5 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Take caution when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. Main Ai Tweaker BIOS SETUP UTILITY Power Boot Tools Exit CPU Configuration Chipset Onboard Devices Configuration USB Configuration PCIPnP Select Screen Select Item Go to Sub Screen General Help Save and Exit Exit Enter F1 F10 ESC v02.
Ratio CMOS Setting: [9] Allows you to set the ratio between the CPU Core Clock and the FSB Frequency. Use <+> and <-> to adjust the value. Configuration options: [ 6] [ 7] [ 8] [ 9] C1E Support [Enabled] Allows you to enable or disable C1E Support.
4.5.2 Chipset The Chipset menu allows you to change the advanced chipset settings. Select an item then press to display the sub-menu. Advanced BIOS SETUP UTILITY Advanced Chipset Settings WARMING: Setting wrong values in below sections may cause system to malfunction. Configure North Bridge features.
4.5.
4.5.4 USB Configuration The items in this menu allows you to change the USB-related features. Select an item then press to display the configuration options. Advanced BIOS SETUP UTILITY USB Configuration Options USB Devices Enabled: None USB Functions USB 2.0 Controller USB 2.
Port 64/60 Emulation [Disabled] Allows you to enable or disable the I/O port 60h/64h emulation support. This item should be enabled for the complete USB keyboard legacy support for non-USB aware OSes. Configuration options: [Disabled] [Enabled] Legacy USB Support [Auto] Allows you to enable or disable the support for legacy USB devices. Setting to [Auto] allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled.
4.6 Power menu The Power menu items allow you to change the settings for the Advanced Power Management (APM). Select an item then press to display the configuration options. Main Ai Tweaker Suspend Mode Repost Video on S3 Resume ACPI 2.0 Support ACPI APIC Support BIOS SETUP UTILITY Advanced Power Boot [Auto] [Disabled] [Disabled] [Enabled] Tools Exit Select the ACPI state used for System Suspend.
4.6.5 APM Configuration BIOS SETUP UTILITY Power APM Configuration Restore on AC Power Loss Power On By RTC Alarm Power On By External Modems Power On By PCI Devices Power On By PCIE Devices Power On By PS/2 Keyboard [Power Off] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] Energy Star 4.0c Support [Disabled] to select whether or not to restart the system after AC power loss. +- F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit v02.
Power On By PS/2 Keyboard [Disabled] Allows you to disable the Power On by PS/2 keyboard function or set specific keys on the PS/2 keyboard to turn on the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Space Bar] [Ctrl-Esc] [Power Key] Energy Star 4.0c Support [Disabled] Setting this item to [Enabled] to pass Energy Star 4.0c rating.
VCORE Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators. Select [Ignored] if you do not want to detect this item. CPU Q-Fan Control [Disabled] Allows you to enable or disable the CPU Q-fan. Configuration options: [Disabled] [Enabled] The following item appears only when you enable CPU Q-Fan Control. CPU Fan Profile [Optimal] Allows you to set the appropriate performance level of the ASUS Q-Fan.
4.7 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press to display the sub-menu. Main BIOS SETUP UTILITY Advanced Power Boot Ai Tweaker Tools Exit Specifies the Boot Device Boot Priority sequence. Boot Device Priority Boot Settings Configuration Security A virtual floppy disk drive (Floppy Drive B: ) may appear when you set the CD-ROM drive as the first boot device.
4.7.2 Boot Settings Configuration BIOS SETUP UTILITY Boot Boot Settings Configuration Quick Boot Full Screen Logo AddOn ROM Display Mode Bootup Num-Lock Wait for ‘F1’ if Error Hit ‘DEL’ Message Display Interrupt 19 Capture [Enabled] [Enabled] [Force BIOS] [On] [Enabled] [Enabled] [Disabled] Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system. +- F1 F10 ESC Select Screen Select Item Change Option General Help Save and Exit Exit v02.
4.7.3 Security The Security menu items allow you to change the system security settings. Select an item then press to display the configuration options. BIOS SETUP UTILITY Boot Security Settings Supervisor Password User Password : Not Installed : Not Installed to change password. again to disabled password. Change Supervisor Password Change User Password Enter F1 F10 ESC Select Screen Select Item Change General Help Save and Exit Exit v02.
BIOS SETUP UTILITY Boot Security Settings Supervisor Password User Password : Installed : Installed to change password. again to disabled password. Change Supervisor Password User Access Level [Full Access] Change User Password Clear User Password Password Check [Setup] Enter F1 F10 ESC Select Screen Select Item Change General Help Save and Exit Exit v02.61 (C)Copyright 1985-2007, American Megatrends, Inc.
4.8 Tools menu The Tools menu items allow you to configure options for special functions. Select an item then press to display the sub-menu. Main Ai Tweaker BIOS SETUP UTILITY Advanced Power Boot Tools Exit Press ENTER to run the utility to select and update BIOS. This utility doesn't support : 1.NTFS format ASUS EZ Flash 2 ASUS O.C. Profile Ai Net 2 Select Screen Select Item Change Field +Enter Go to Sub Screen F1 General Help F10 Save and Exit ESC Exit v02.
4.8.2 ASUS O.C. Profile This item allows you to store or load multiple BIOS settings. BIOS SETUP UTILITY Tools O.C. PROFILE Configuration O.C. Profile 1 Status O.C. Profile 2 Status Save to Profile 1 : Not Installed : Not Installed Save to Profile 1 Load from Profile 1 Save to Profile 2 Load from Profile 2 Start O.C. Profile Enter F1 F10 ESC Select Screen Select Item Go to Sub Screen General Help Save and Exit Exit v02.61 (C)Copyright 1985-2007, American Megatrends, Inc.
4.8.3 Ai Net 2 BIOS SETUP UTILITY Tools Marvell Check LAN cable during POST. Pair Status Length 1-2 3-6 4-5 7-8 N/A N/A N/A N/A Marvell Controller 0 1-2 3-6 4-5 7-8 N/A N/A N/A N/A Realtek Controller 0 Marvell POST Check LAN cable Realtek POST Check LAN cable [Disabled] [Disabled] v02.61 (C)Copyright 1985-2007, American Megatrends, Inc. Marvell POST Check LAN Cable [Disabled] Enables or disables checking of the Marvell LAN cable during the Power-On Self‑Test (POST).
4.9 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items. Main Ai Tweaker BIOS SETUP UTILITY Advanced Power Boot Exit & Save Changes Exit & Discard Changes Discard Changes Tools Exit Exit system setup after saving the changes. F10 key can be used for this operation.
This chapter describes the contents of the support DVD that comes with the motherboard package and the softwares.
Chapter summary 5 5.1 Installing an operating system.................................................... 5-1 5.2 Support DVD information............................................................. 5-1 5.3 Software information.................................................................... 5-9 5.4 RAID configurations................................................................... 5-35 5.5 Creating a RAID driver disk........................................................
5.1 Installing an operating system This motherboard supports Windows® XP/ 64-bit XP/ Vista™ operating systems (OS). Always install the latest OS version and corresponding updates to maximize the features of your hardware. 5.2 • Motherboard settings and hardware options vary. Use the setup procedures presented in this chapter for reference only. Refer to your OS documentation for detailed information.
5.2.2 Drivers menu The Drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. ASUS EPU + AI Gear 3 Driver ASUS InstAll-Drivers Installation Wizard Installs all of the drivers through the Installation Wizard. Intel Chipset Inf Update Program Installs the Intel® chipset Inf update program. SoundMAX ADI1988 Audio Driver Installs the SoundMAX® ADI1988 audio driver and application.
5.2.3 Utilities menu The Utilities menu shows the applications and other software that the motherboard supports. Click to display the next page Click to return to the previous page ASUS InstAll-Installation Wizard for Utilities Installs all of the utilities through the Installation Wizard. ASUS Update The ASUS Update utility allows you to update the motherboard BIOS in Windows® environment. This utility requires an Internet connection either through a network or an Internet Service Provider (ISP).
ASUS AI Suite The ASUS AI Suite is an innovative application to do overclocking, fan control, power saving and quiet thermal control. ASUS AI Direct Link The ASUS AI Direct Link provides up to 70% transferring speed improvement when compared to traditional USB 2.
5.2.4 Make disk menu The Make disk menu contains items to create the Intel ICH9 or JMicron® JMB36X RAID/AHCI driver disk. Make Intel ICH9 32/64bit RAID/AHCI Driver Disk Allows you to create an ICH9 32/64bit RAID/AHCI driver disk. Make JMicron JMB36X 32/64bit RAID/AHCI Driver Allows you to create a JMicron® JMB36X 32/64bit RAID/AHCI driver.
5.2.5 Manual menu The Manual menu contains a list of supplementary user manuals. Click an item to open the folder of the user manual. Most user manual files are in Portable Document Format (PDF). Install the Adobe® Acrobat® Reader from the Utilities menu before opening a user manual file. 5.2.6 ASUS Contact information Click the Contact tab to display the ASUS contact information. You can also find this information on the inside front cover of this user guide.
5.2.7 Other information The icons on the top right corner of the screen give additional information on the motherboard and the contents of the support DVD. Click an icon to display the specified information. Motherboard Info Displays the general specifications of the motherboard. ASUS EPU + AI Gear 3 Driver Browse this DVD Displays the support DVD contents in graphical format.
Technical support Form Displays the ASUS Technical Support Request Form that you have to fill out when requesting technical support. Filelist Displays the contents of the support DVD in text format.
5.3 Software information Most of the applications in the support DVD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software application for more information. 5.3.1 ASUS MyLogo3™ The ASUS MyLogo3™ utility lets you customize the boot logo. The boot logo is the image that appears on screen during the Power‑On‑Self-Tests (POST).
7. When the logo images appear on the right window pane, select an image to enlarge by clicking on it. 8. Adjust the boot image to your desired size by selecting a value on the Ratio box. 9. When the screen returns to the ASUS Update utility, flash the original BIOS to load the new boot logo. 10. After flashing the BIOS, restart the computer to display the new boot logo during POST.
5.3.2 AI NET2 The AI NET2 features the Marvell® Virtual Cable Tester™ (VCT). VCT is a cable diagnostic utility that reports LAN cable faults and shorts using the Time Domain Reflectometry (TDR) technology. The VCT detects and reports open and shorted cables, impedance mismatches, pair swaps, pair polarity problems, and pair skew problems of up to 64 ns at one meter accuracy. The VCT feature reduces networking and support costs through a highly manageable and controlled network system.
5.3.3 ASUS PC Probe II PC Probe II is a utility that monitors the computer’s vital components, and detects and alerts you of any problem with these components. PC Probe II senses fan rotations, CPU temperature, and system voltages, among others. Because PC Probe II is software-based, you can start monitoring your computer the moment you turn it on. With this utility, you are assured that your computer is always at a healthy operating condition.
Button Function Opens the Configuration window Opens the Report window Opens the Desktop Management Interface window Opens the Peripheral Component Interconnect window Opens the Windows Management Instrumentation window Opens the hard disk drive, memory, CPU usage window Shows/Hides the Preference section Minimizes the application Closes the application Sensor alert When a system sensor detects a problem, the main window right handle turns red, as the illustrations below show.
Hardware monitor panels The hardware monitor panels display the current value of a system sensor such as fan rotation, CPU temperature, and voltages. The hardware monitor panels come in two display modes: hexagonal (large) and rectangular (small). When you check the Enable Monitoring Panel option from the Preference section, the monitor panels appear on your computer’s desktop.
Monitoring sensor alert The monitor panel turns red when a component value exceeds or is lower than the threshold value. Refer to the illustrations below. Small display Large display WMI browser Click to display the WMI (Windows Management Instrumentation) browser. This browser displays various Windows® management information. Click an item from the left panel to display on the right panel. Click the plus sign (+) before WMI Information to display the available information.
PCI browser Click to display the PCI (Peripheral Component Interconnect) browser. This browser provides information on the PCI devices installed on your system. Click the plus sign (+) before the PCI Information item to display available information. Usage The Usage browser displays real-time information on the CPU, hard disk drive space, and memory usage. Click to display the Usage browser. CPU usage The CPU tab displays realtime CPU usage in line graph representation.
Memory usage The Memory tab shows both used and available physical memory. The pie chart at the bottom of the window represents the used (blue) and the available physical memory. Configuring PC Probe II Click to view and adjust the sensor threshold values. The Config window has two tabs: Sensor/Threshold and Preference. The Sensor/ Threshold tab enables you to activate the sensors or to adjust the sensor threshold values.
5.3.4 ASUS AI Suite ASUS AI Suite allows you to launch AI Gear 3, AI Booster, AI Nap, and Q-Fan 2 utilities easily. Install the ASUS EPU + AI Gear 3 Driver before the ASUS AI Suite utility. Otherwise, ASUS AI Suite will not function properly. Installing AI Suite To install AI Suite on your computer: 1. Place the support DVD to the optical drive. The Drivers installation tab appears if your computer has an enabled Autorun feature. 2. Click the Utilities tab, then click AI Suite. 3.
Other feature buttons Click on right corner of the main window to open the monitor window. Displays the CPU/ system temperature, CPU/memory/PCIE voltage, and CPU/ chassis fan speed Displays the FSB/CPU frequency Click on right corner of the expanded window to switch the temperature from degrees Centigrade to degrees Fahrenheit.
5.3.5 ASUS EPU Utility -- AI Gear 3 ASUS AI Gear 3 is a utility designed to configure and support all ASUS EPU (Energy Processing Unit) features. This easy-to-use utility provides four system performance profiles that adjusts the processor frequency and vCore voltage for different computing needs.
5.3.6 ASUS AI Nap This feature allows you to minimize the power consumption of your computer whenever you are away. Enable this feature for minimum power consumption and a more quiet system operation. After installing AI Suite from the bundled support DVD, you can launch the utility by double-clicking the AI Suite icon on the Windows OS taskbar and click the AI Nap button on the AI Suite main window. Click Yes on the confirmation screen.
5.3.7 ASUS Q-Fan 2 This ASUS Q-Fan 2 Control feature allows you to set the appropriate performance level of the CPU Q-Fan 2 or the Chassis Q-Fan 2 for more efficient system operation. After enabling the Q-Fan 2 function, the fans can be set to automatically adjust depending on the temperature, to decrease fan speed, or to achieve the maximum fan speed.
5.3.8 ASUS AI Booster The ASUS AI Booster application allows you to overclock the CPU speed in WIndows® environment without the hassle of booting the BIOS. After installing AI Suite from the bundled support DVD, you can launch the utility by double-clicking the AI Suite icon on the Windows® OS taskbar and click the AI Booster button on the AI Suite main window.
5.3.9 ASUS AI Direct Link ASUS AI Direct Link allows you to form a computer-to-computer network via a network cable to share files with high transfer rate. You must first connect two computers (at least one of them is ASUS product) using a network cable, and then install the utility to both computers to avail the AI Direct Link feature. • Turn off your firewall software other than Windows Firewall before launching AI Direct Link. • The transfer rate is limited if you use a 10/100 LAN card.
4. Right click on the AI Direct Link icon and select Incoming folder > Open incoming folder. The AIDirectLinkIncoming folder opens. Put the files you want to share into this folder. The authorized user has full access to this folder. The default path of the AIDirectLinkIncoming folder is C:\Program Files\ASUS\AI Direct Link. To change its location, disable the incoming folder first.
5.3.10 AI Audio 2 (SoundMAX® High Definition Audio utility) The ADI AD1988 High Definition Audio CODEC provides 8-channel audio capability through the SoundMAX® audio utility with AudioESP™ software to deliver the ultimate audio experience on your PC. The software implements high quality audio synthesis/rendering, 3D sound positioning, and advanced voice-input technologies.
A. SoundMAX BlackHawk (AI Audio 2) If you are using Windows Vista™ operating system, from the taskbar, double-click on the SoundMAX® BlackHawk icon to display the SoundMAX® control panel. Enabling AI Audio 2 Click the power button to activate digital signal processing. AI Audio 2, with the new SoundMAX® BlackHawk by Sonic Focus, brings you more multimedia enjoyment.
Playback Settings To configure the playback settings, click the Playback button on the control panel. You can adjust the volume of the Speakers and SPDIF Interface or mute the audio. Preset settings Click and expand the drop-down menu to select your preferred Digital Signal Processing (DSP) preset. Move the sliders to customize the values of Voice Clarity, Dynamics, Brilliance, and Deep Bass of each preset. Click Save to save the changes to the current preset.
Recording Settings To change the recording settings, click the Recording button on the control panel. You can adjust the speaker delay of Microphone or Line In by moving the slider rightward or leftward. Record testing Port settings Click the tab to perform test recording and play the test sample through the speakers or the SPDIF interface. Click the tab to display the rear panel ports for Microphone or Line In.
Speakers Allows you to adjust the Speaker Trim and Speaker Delay. Bass Allows you to do the Bass management. Preferences Displays the preference options for this utility, version information, AudioESP, etc.
B. SoundMAX If you are using Windows XP operating system, from the taskbar, double-click on the SoundMAX® icon to display the SoundMAX® Control Panel. Audio Setup Wizard By clicking the icon from the SoundMAX® control panel, you can easily configure your audio settings. Simply follow succeeding screen instructions and begin enjoying High Definition Audio.
Jack configuration Adjust speaker volume This screen helps you configure your computer’s audio ports, depending on the audio devices you have installed. This screen helps you adjust speaker volume. Click the Test button to hear the changes you have made. Adjust microphone volume This screen helps you adjust microphone volume. You will be asked to read prewritten text to allow the AudioWizard to adjust the volume as you speak.
Audio preferences Click the icon to go to the Preferences page. This page allows you to change various audio settings. General options Click the General tab to choose your playback and recording devices, enable/ disable the AudioESP™ feature, and enable/disable digital output. Listening Environment options Click the Listening Environment tab to set up your speaker, acoustic environment, and enable/disable the Virtual Theater Surround function.
Microphone options Click the Microphone tab allows you to optimize your microphone input settings. Enhanced Microphone Features Voice recording Enables Noise Filter function. Detects repetitive and stationary noises like computer fans, air conditioners, and other background noises then eliminates it in the incoming sudio stream while recording. You can enable it for a better recording quality.
5.4 RAID configurations The motherboard comes with two RAID controllers that allow you to configure Serial ATA hard disk drives as RAID sets. • The Intel® ICH9R Southbridge RAID includes a high performance SATA RAID controller that supports RAID 0, RAID 1, RAID 10, and RAID 5 for six independent Serial ATA channels. • The JMicro® JMB363 RAID includes a high performance SATA RAID controller that supports RAID 0, 1, and JBOD for two independent Serial ATA channels. 5.4.
If you want to boot the system from a hard disk drive included in a created RAID set, copy first the RAID driver from the support DVD to a floppy disk before you install an operating system to the selected hard disk drive. Refer to section 5.5 Creating a RAID driver disk for details. 5.4.2 Installing Serial ATA hard disks The motherboard supports Serial ATA hard disk drives. For optimal performance, install identical drives of the same model and capacity when creating a disk array.
Intel® Matrix Storage Manager Option ROM Utility The Intel® Matrix Storage Manager Option ROM utility allows you to create RAID 0, RAID 1, RAID 10 (RAID 0+1), and RAID 5 set(s) from Serial ATA hard disk drives that are connected to the Serial ATA connectors supported by the Southbridge. To enter the Intel® Application Accelerator RAID Option ROM utility: 1. Install all the Serial ATA hard disk drives. 2. Turn on the system. 3. During POST, press to display the utility main menu.
Creating a RAID 0 set (striped) To create a RAID 0 set: 1. From the utility main menu, select 1. Create RAID Volume, then press . This screen appears. Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH9R wRAID5 Copyright(C) 2003-05 Intel Corporation. All Rights Reserved. [ CREATE ARRAY MENU ] Name: RAID Level: Disks: Strip Size: Capacity: Volume0 RAID0(Stripe) Select Disks 128KB 0.
6. Use the up/down arrow key to select the stripe size for the RAID 0 array, then press . The available stripe size values range from 4 KB to 128 KB. The default stripe size is 128 KB. We recommend a lower stripe size for server systems, and a higher stripe size for multimedia computer systems used mainly for audio and video editing. 7. Key in the RAID volume capacity that you want, then press . The default value indicates the maximum allowed capacity. 8.
Creating a RAID 1 set (mirrored) To create a RAID 1 set: 1. From the utility main menu, select 1. Create RAID Volume, then press . This screen appears. Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH9R wRAID5 Copyright(C) 2003-05 Intel Corporation. All Rights Reserved. [ CREATE ARRAY MENU ] Name: RAID Level: Disks: Strip Size: Capacity: Volume1 RAID1(Mirror) Select Disks N/A XX.
Creating a RAID 10 set (RAID 0+1) To create a RAID 10 set: 1. From the utility main menu, select 1. Create RAID Volume, then press . This screen appears. Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH9R wRAID5 Copyright(C) 2003-05 Intel Corporation. All Rights Reserved. [ CREATE ARRAY MENU ] Name: RAID Level: Disks: Strip Size: Capacity: Volume10 RAID10(RAID0+1) Select Disks 128KB XXX.
6. Press when the Create Volume item is highlighted. This warning message appears. WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST. Are you sure you want to create this volume? (Y/N): 7. Press to create the RAID volume and return to the main menu or to go back to the Create Volume menu. Creating a RAID 5 set (parity) To create a RAID 5 set: 1. From the utility main menu, select 1. Create RAID Volume, then press . This screen appears.
4. The Disks item is highlighted, press to select the hard disk drives to configure as RAID. The following pop‑up screen appears. [ SELECT DISKS ] Port 0 1 2 3 Drive Model XXXXXXXXXXXX XXXXXXXXXXXX XXXXXXXXXXXX XXXXXXXXXXXX Serial # XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX Size XX.XGB XX.XGB XX.XGB XX.XGB Status Non-RAID Non-RAID Non-RAID Non-RAID Disk Disk Disk Disk Select 2 to 4 disks to use in creating the volume. [↑↓]-Previous/Next [SPACE]-Selects [ENTER]-Selection Complete 5.
5.4.4 JMicron® RAID Configuration The JMicron® Serial ATA controller allows you to configure RAID 0, RAID 1 and JBOD sets on the external Serial ATA hard disk drives. Before creating a RAID set Prepare the following items: 1. Two SATA HDDs, preferably with the same model and capacity. 2. A write-enabled floppy disk (Windows XP). A write-enabled floppy disk or a USB flash disk drive (Windows Vista) 3. Microsoft® Windows® OS installation disk (Windows XP) 4.
Entering the JMB363 RAID BIOS utility 1. During POST, press to enter the JBM363 RAID BIOS menu. JMicron Technology Corp. PCI-to-SATA II/IDE RAID Controller BIOS v0.97 Copyright (C) 2004-2005 JMicron Technology http://www. jmicron.com HDD0 : HDS722516VLSA80 HDD1 : HDS722516DLA380 164 GB Non-RAID 164 GB Non-RAID Press to enter RAID Setup Utility... 2. The main JMB363 RAID BIOS menu appears. 3. Use the arrow keys to move the color bar and navigate through the items.
2. When the Level item is highlighted, use the up/down arrow key to select the RAID set that you want to create. [Create New RAID] Name : JRAID Level: 0-Stripe Disks: Select Disk Block: 128 KB Size : 319 GB [Create New RAID] Name : JRAID Level: 1-Mirror Disks: Select Disk Block: N/A Size : 159 GB Confirm Creation 3. Confirm Creation When the Disks item is highlighted, use the up/down arrow key to highlight an HDD that you want to belong to the RAID set, then press the space bar to confirm selection.
5. When done, press to confirm the creation of the RAID set. A dialogue box appears to confirm the action. Press to confirm; otherwise, press . JMicron Technology Corp. PCI-to-SATA II/IDE RAID Controller BIOS v0.
Deleting a RAID set 1. In the main JMB363 RAID BIOS menu, highlight Delete RAID Disk Drive using the up/down arrow key then press . [Main Menu] Create RAID Disk Drive Delete RAID Disk Drive Revert HDD to Non-RAID Solve Mirror Conflict Rebuild Mirror Drive Save and Exit Setup Exit Without Saving 2. Use the space bar to select the RAID set you want to delete. A selected set shows a set. 3. sign before it. Press the key to delete the A dialogue box appears to confirm the action.
Resetting disks to non-RAID • An HDD that has been previously configured as part of another RAID set in another platform is called a broken RAID HDD. When you install a broken RAID HDD, you cannot select this HDD when configuring a RAID set through the JMB363 utility. • If you still want to use this broken RAID HDD as part of the RAID set configured through the JMB363, you may do so by resetting the disk to nonRAID. You will, however, lose all data and previous RAID configurations.
Solving a Mirror conflict A Mirror conflict occurs when both disks in a RAID 1 (Mirror) configuration are unplugged from the system in turn, then plugged in again. Since both disks contain exactly the same data, the system will be unable to determine which of the two is the source drive. This option allows you to set the source drive and rebuild the Mirror drive according to the contents of the source drive. To solve a Mirror conflict: 1.
Rebuilding a Mirror Drive When one of the disks in a RAID 1 (Mirror) configuration is unplugged from the system, then plugged in again, a dialogue box appears to ask you to rebuild the Mirror drive. Press to confirm; otherwise, press . This option allows you to rebuild the Mirror drive later and synchronize the data between two hard disks. To rebuild a Mirror drive: 1. In the main JMB363 RAID BIOS menu, highlight Rebuild Mirror Drive using the up/down arrow key then press .
5.5 Creating a RAID driver disk A floppy disk with the RAID driver is required when installing Windows® XP/Vista and later operating system on a hard disk drive that is included in a RAID set. For Windows Vista user, you can create a RAID driver disk with a floppy disk drive or a USB flash disk drive. 5.5.1 Creating a RAID driver disk without entering the OS To create a RAID driver disk without entering the OS: 1. Boot your computer. 2. Press during POST to enter the BIOS setup utility. 3.
To install the RAID driver in Windows XP: 1. During the OS installation, the system prompts you to press the key to install third-party SCSI or RAID driver. 2. Press then insert the floppy disk with RAID driver into the floppy disk drive. 3. When prompted to select the SCSI adapter to install, make sure you select Intel(R) SATA RAID Controller (Desktop ICH9R) and JMicron JMB363. 4. Follow the succeeding screen instructions to complete the installation.
5-54 Chapter 5: Software support
This chapter tells how to install ATI® CrossFire™ graphics cards to avail of ATI’s Multi-Video Processing technology.
Chapter summary 6 6.1 Overview........................................................................................ 6-1 6.2 Installing CrossFire™ graphics cards........................................ 6-2 6.3 Software information....................................................................
6.1 Overview The motherboard supports the ATI® CrossFire™ technology that allows you to install multi-graphics processing units (GPU) graphics cards. Follow the installation procedures in this section. 6.1.1 Requirements • CrossFire™ Edition graphics card (Master) • CrossFire™-ready graphics card (Slave) • CrossFire™-ready motherboard • Make sure that your power supply unit (PSU) can provide at least the minimum power required by your system. See 8. ATX Power connectors on page 2-32 for details.
6.2 Installing CrossFire™ graphics cards Before installing a CrossFire™ system, refer to the user guide that came with the ATI® CrossFire™ Edition graphics card. To install the graphics cards: 1. Prepare one CrossFire™ Edition (Master) graphics card and one CrossFire™-ready (Slave) graphics card. Slave graphics card 2. 6- Master graphics card Insert the CrossFire™ Edition (Master) graphics card into the PCI Express x16 blue slot. Make sure that the card is properly seated on the slot.
3. Insert the CrossFire™-ready (Slave) graphics card into the PCI Express x16 black slot. Make sure that the card is properly seated on the slot. 4. Connect an auxiliary power source from the power supply to the graphics cards.
5. Connect one end of the external cable to the Master graphics card. 6. Connect the other end of the external cable to the Slave graphics card. 7. Connect the loose end to the corresponding port on your monitor.
6.3 Software information 6.3.1 Installing the device drivers Refer to the documentation that came with your graphics card package to install the device drivers. The ATI CrossFire™ technology supports only the following operating systems: • Windows® XP 32-bit (Home or Professional) with Service Pack 2 (SP2) • Windows® XP Professional 64-bit Edition. • Windows® Vista 32/64 bit Edition. (Will be ready later. Visit the ATI website (www.ati.com) 1.
6. Select the components that you want to install, then click Next. • Select Express to install the HydraVision™ multi-monitor and desktop management software, as well as the ATI driver. • Select Custom to individually choose desired software components. Setup prepares the installation wizard that will guide you to setup process. Windows automatically configures the ATI Catalyst Control Center. The status windows indicates the progress of the installation. 7.
6.3.2 Using the Catalyst™ Control Center The Catalyst™ Control Center allows you to access display features of the ATI hardware and software you installed. Use this application to adjust your graphic settings, enable/disable connected devices, and change your desktop orientation.
The Catalyst™ Control Center Dialog Box View The Catalyst™ Control Center provides two views: Standard - simple view with wizards for beginners Advance - allows advanced users to access and configure the complete features of the software Set to Advance view to enable the CrossFire™ function.
To enable CrossFire™: 1. Set the view to Advance. 2. Click the Crossfire™ item in Graphics Settings. 3. In the CrossFire™ Settings dialog, tick the box opposite Enable CrossFire™. 4. Click OK to effect the setting. 3 2 4 Hotkeys Click the Hotkeys tab on the Catalyst™ Control Center to access the Hotkeys Manager, which allows you to create key combinations as shortcuts for performing certain functions quickly.
Profiles Click the Profiles tab on the Catalyst™ Control Center to access the Profiles Manager, which allows you to create customized environments for your desktop, video, and 3D applications. Preferences Click the Preferences tab on the Catalyst™ Control Center to select a language, restore defaults, change skins, or enable/disable the System Tray icon.
Help Click the Help tab on the Catalyst™ Control Center to access the online help system, generate a Problem Report, and get the Catalyst™ Control Center version information.
6-12 Chapter 6: ATI® MVP technology support
The Appendix describes the CPU features and technologies that the motherboard supports.
Chapter summary A.1 A.2 A.3 ® A Intel EM64T...................................................................................A-1 Enhanced Intel SpeedStep® Technology (EIST).........................A-1 Intel® Hyper-Threading Technology............................................
A.1 Intel® EM64T • The motherboard is fully compatible with Intel® LGA775 processors running on 32-bit operating systems. • The motherboard comes with a BIOS file that supports EM64T. You can download the latest BIOS file from the ASUS website (www.asus.com/ support/download/) if you need to update the BIOS file. See Chapter 4 for details. • Visit www.intel.com for more information on the EM64T feature. • Visit www.microsoft.com for more information on Windows® 64-bit OS.
A.2.2 Using the EIST To use the EIST feature: 1. Turn on the computer, then enter the BIOS Setup. 2. Go to the Advanced Menu, highlight CPU Configuration, then press . 3. Set the Intel(R) SpeedStep Technology item to [Automatic], then press . 4. Press to save your changes and exit the BIOS setup. 5. After the computer restarts, right click on a blank space on the desktop, then select Properties from the pop-up menu. 6.
A.3 Intel® Hyper-Threading Technology • The motherboard supports Intel® Pentium® 4 LGA775 processors with Hyper-Threading Technology. • Hyper-Threading Technology is supported under Windows® Vista/XP and Linux 2.4.x (kernel) and later versions only. Under Linux, use the HyperThreading compiler to compile the code. If you are using any other operating systems, disable the Hyper-Threading Technology item in the BIOS to ensure system stability and performance.
A- Appendix: CPU features
