Motherboard P5G41C-M LX
J5284 初版 第1刷 2011年1月 Copyright © 2011 ASUSTeK COMPUTER INC。All Rights Reserved. バックアップの目的で利用する場合を除き、本書に記載されているハードウェア・ソフトウェアを含む、全ての内 容は、ASUSTeK Computer Inc.
もくじ ご注意 ..............................................................................................................vi 安全上のご注意................................................................................................vii このマニュアルについて.....................................................................................vii P5G41C-M LX 仕様一覧....................................................................................ix Chapter 1 製品の概要 1.1 ようこそ.....................................................
もくじ 1.11 ソフトウェア...................................................................................... 1-30 1.11.1 OSをインストールする...................................................................1-30 1.11.2 サポートDVD情報............................................................................1-30 Chapter 2 2.1 2.2 2.3 2.4 2.5 iv BIOS情報 BIOS管理更新.................................................................................... 2-1 2.1.1 ASUS Update...................................................
もくじ 2.6 2.7 2.8 2.5.4 Anti Surge Support [Enabled]....................................................2-15 2.5.5 APM Configuration........................................................................2-16 2.5.6 ハードウェアモニター.....................................................................2-16 ブートメニュー................................................................................. 2-17 2.6.1 ブートデバイスの優先順位..........................................................2-17 2.6.2 起動設定.................
ご注意 Federal Communications Commission Statement(原文) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
安全上のご注意 電気の取り扱い • 作業を行う場合は、感電防止のため、電源コードをコンセントから抜いてから行ってくださ い。 ・ 周辺機器の取り付け・取り外しの際は、本製品および周辺機器の電源コードをコンセントから 抜いてから行ってください。可能ならば、関係するすべての機器の電源コードをコンセントから 抜いてから行ってください。 ・ ケーブルの接続・取り外しの際は、電源コードをコンセントから抜いてから行ってください。 ・ 電源延長コードや特殊なアダプターを用いる場合は専門家に相談してください。これらは、回 路のショート等の原因になる場合があります。 ・ 正しい電圧でご使用ください。ご使用になる地域の出力電圧がわからない場合は、お近くの電 力会社にお尋ねください。 ・ 電源装置の修理は販売代理店などに依頼してください。 操作上の注意 • 作業を行う前に、本パッケージに付属のマニュアル及び取り付ける部品のマニュアルを全て 熟読してください。 ・ 電源を入れる前に、ケーブルが正しく接続されていることを確認してください。また電源コード に損傷がないことを確認してください。 ・ マザー
このマニュアルの表記について 本製品を正しくお取り扱い頂くために以下の表記を参考にしてください。 危険/警告:本製品を取り扱う上で、人体への危険を避けるための情報です。 注意:本製品を取り扱う上で、 コンポーネントへの損害を避けるための情報です。 重要:作業を完了するために、従わなければならない指示です。 注記:本製品を取り扱う上でのヒントと 追加情報です。 詳細情報 本書に記載できなかった最新の情報は以下で入手することができます。また、BIOSや添付ソフト ウェアの最新版があります。必要に応じてご利用ください。 1. ASUS Webサイト (http://www.asus.co.jp/) 各国や地域に対応したサイトを設け、ASUSのハードウェア・ソフトウェア製品に関する最新 情報が満載です。 2.
P5G41C-M LX 仕様一覧 CPU LGA775 ソケット:Intel® Core™2 Quad / Core™2 Extreme / Core™2 Duo / Pentium® デュアルコア / Celeron® デュアルコア / Celeron® プロセッサー対応 Intel®05B/05A/06 プロセッサー対応 Intel® 45nm マルチコアCPUをサポート * 詳細は弊社サイトの Intel® CPUサポートリストをご参照ください。 (http://www.asus.co.jp) チップセット ノースブリッジ:Intel® G41 サウスブリッジ:Intel® ICH7 フロントサイドバス 1333/1066/800 MHz メモリー デュアルチャンネルメモリーアーキテクチャ - 240ピンメモリースロット×2:unbuffered non-ECC 1333(O.C.)/1066/800 MHz DDR3 メモリー対応 - 240ピンメモリースロット×2:unbuffered non-ECC 1066(O.C.
P5G41C-M LX 仕様一覧 ASUSだけの機能 SFS (Stepless Frequency Selection): - FSB 調節:1 MHz 刻みで 200MHz 〜800 MHz オーバークロックプロテクション: - ASUS C.P.R. (CPU Parameter Recall) 特殊機能 ASUS CrashFree BIOS 3 ASUS AI NET 2 ASUS Q-Fan ASUS EZ Flash 2 ASUS MyLogo 2 ASUS アンチサージプロテクション ASUS Turbo Key ASUS Express Gate ASUS EPU-L バックパネル I/Oポート PS/2 キーボードポート×1 PS/2 マウス ポート×1 LPT ポート×1 COM ポート×1 VGA ポート×1 LAN (RJ-45) ポート×1 USB 2.0 ポート×4 オーディオジャック×3 内部コネクター USB 2.0コネクター������������������� ×2:追加USB2.
Chapter 1 製品の概要 1.1 ようこそ 本マザーボードをお買い上げいただき、ありがとうございます。本マザーボードは多くの新機能と 最新のテクノロジを提供するASUSの高品質マザーボードです。 マザーボードとハードウェアデバイスの取り付けを始める前に、パッケージの中にリストに掲載さ れている部品が揃っていることを確認してください。 1.2 パッケージの内容 マザーボードパッケージに以下のものが揃っていることを確認してください。 マザーボード ASUS P5G41C-M LX マザーボード ケーブル Serial ATAケーブル×2 Ultra DMA 133/100/66 ケーブル×1 アクセサリ I/O Shield×1 アプリケーション DVD ASUSマザーボード サポートDVD ユーザーマニュアル(本書) ドキュメント 付属品が足りないときや破損しているときは、お手数ですが販売店様にご連絡ください。 1.3 独自機能 1.3.
Intel® G41チップセット Intel® G41 Express チップセットは、デュアルチャンネルDDR3 1333(オー バークロック時)/1066/800 アーキテクチャー、FSB 1333/1066/800、PCI Express 1.1、マルチコアCPUをサポートしています。Intel® Fast メモリー帯域 の採用でメモリーの遅延を短縮します。 デュアルチャンネルDDR3 1333(O.C.)/1066/800 サポート 本マザーボードはDDR3 メモリーをサポートし、1333(O.C.)/1066/800 MHz のデータ転送速度により、特に3Dグラフィックスや、より高いメモリー性能 が要求されるアプリケーションでシステムパフォーマンスの向上が期待でき ます。 Serial ATA 3Gb/s テクノロジ Serial ATA(SATA)3.
ASUS Express Gate ASUS Express Gate はWindows を起動しなくても、インターネットや主なア プリケーションを使用できる、Linux ベースの高速起動OSです。 • ASUS Express Gate はSATA HDD、USB HDD、フラッシュメモリーにインストールが可能 です。インストールに必要なディスク領域は1.
1.
1.5 マザーボードの概要 マザーボードを設置する前にケースの仕様を確認し、マザーボードが設置できることをご確認く ださい。 マザーボードを設置する、または取り外す前に電源プラグを抜いてください。怪我または、マザ ーボードの故障の原因になります。 1.5.1 設置方向 マザーボードが正しい向きでケースに取り付けられているかを確認してください。 下の図のように外部ポートをケースの背面部分に合わせます。 1.5.
1.5.3 マザーボードのレイアウト 1 2 3 4 5 5 6 21.6cm(8.5in) KBPWR KBMS CPU_FAN Intel® G41 ICS 9LRS954 PRI_IDE 7 24.4cm(9.
1.
2. ロードレバーを親指で押し(A)、タブから 離れるまでずらします。B)。 タブ A ソケットピンの損傷防止のため、ソケ ットキャップはCPUを取り付けるまで 外さないでください。 B ロードレバー 3. 4. 矢印の方向にロードレバーを135º程持ち 上げます。 ソケットキャップ ロードプレート 4B 親指と人差し指でロードプレートを100º 持ち上げ(4A)、ソケットキャップを押して ロードプレートから取り外します(4B)。 4A 3 5.
6. ヒートシンクを取り付けるため、サーマルグ リス(放熱グリス)をCPUの表面に薄く均一 に塗布します。 ヒートシンクによっては既にサーマルグ リスが塗布されています。その場合は この手順は行わず、次の手順に進んで ください。 サーマルグリスは有毒物質を含んでいます。万一目や口に入った場合や、肌に直接触れた場合 は洗浄後、すぐに医師の診断を受けてください。 サーマルグリスは指で直接塗布しないでください。汚れ等が付き、効果が下がる場合があり ます。 7.
1.6.2 CPUにヒートシンクとファンを取り付ける Intel® LGA775 プロセッサー用に特別に設計されたヒートシンクとファンを組み合わせることで、 効率的な冷却を行いCPUのパフォーマンスを引き出します。 • BOX版の Intel® プロセッサーを購入した場合、パッケージにはCPUクーラーが入っていま す。CPUのみをお求めになった場合、Intel® が認定したマルチディレクションヒートシンクと ファンを必ずご使用ください。 • BOX版の Intel® プロセッサーに付属するCPUクーラーは、プッシュピンデザインが採用され ており、取り付けの際に特別な工具は必要ありません。 • CPUヒートシンクとファンを別々にお買い求めになった場合は、ヒートシンクとファンを取り 付ける前に、サーマルグリスがヒートシンクまたはCPUに塗布されていることを確認してくだ さい。 組み立てに支障がない限り、CPUファンとヒートシンクを取り付ける前に、ケースにマザーボー ドを取り付けてください。 CPUヒートシンクとファンの取り付け手順 1.
3. マザーボード上のCPU_FAN コネクターにCPUファン電源ケーブルを接続します。 CPU FAN PWM CPU FAN IN CPU FAN PWR GND CPU_FAN P5G41C-M LX P5G41C-M LX CPU fan connector ハードウェアモニタリングエラーが発生した場合は、CPUファンの接続を再度確認してくださ い。 1.6.3 CPUからヒートシンクとファンを取り外す 手順 1. マザーボードのコネクターからCPUファンのケーブルを抜きます。 2. 各プッシュピンを左へ回します。 3.
4. マザーボードからヒートシンクとファンを慎重 に取り外します。 5. 各プッシュピンを右へ回します。 1.7 システムメモリー 1.7.
1.7.
DDR3-1333(O.C.) MHz メモリースロット サポート (オプション) ベンダー パーツNo. サイズ SS/DS チップ ブランド チップNO. タイミング 電圧 A-Data AD31333001GOU 1024MB SS A-Data AD30908C8D-151CE0906 - - • • A-Data AD31333G001GOU 3072MB(Kit of 3) SS - - 8-8-8-24 1.65-1.85V • • A-Data AD31333002GOU 2048MB DS A-Data AD30908C8D-151CE0903 - - • • A-Data AD31333G002GMU 2048MB DS - - 8-8-8-24 1.65-1.85V • • Apacer 78.A1GC6.
DDR3-1333(O.C.) MHz メモリースロット サポート (オプション) チップ ブランド チップNO. タイミング 電圧 4096MB(Kit of 2) DS - - 7-7-7-20 1.8V • • OCZ3P1333LV4GK 4096MB(Kit of 2) DS - - 7-7-7-20 1.65V(low voltage) • • OCZ OCZ3P1333LV4GK 4096MB(Kit of 2) DS - - 7-7-7-20 1.65V • • OCZ OCZ3RPX1333EB4GK 4096MB(Kit of 2) DS - - 6-5-5-20 1.85V • • OCZ OCZ3X13334GK(XMP) 4096MB(Kit of 2) DS - - 7-7-7-20 1.75V • • OCZ OCZ3G1333LV6GK 6144MB(Kit of 3) DS - - 9-9-9-20 1.
DDR2-667 MHz メモリースロット サポート (オプション) ベンダー パーツNo. サイズ SS/DS チップ ブランド チップNO. タイミング 電圧 A-Data M2OAD5H3J4170I1C53 2048MB DS A-Data AD20908A8A-3EG 30724 - - • • G.SKILL F2-5400PHU2-2GBNT 2048MB(Kit of 2) DS G.SKILL D2 64M8CCF 0815 C7173S 5-5-5-15 - • • G.SKILL F2-5300CL5D-4GBMQ 4096MB(Kit of 2) DS G.
DDR2-800 MHz メモリースロット サポート (オプション) ベンダー パーツNo. サイズ SS/DS チップ ブランド チップNO. タイミング 電圧 GEIL GE24GB800C5QC 1024MB DS GEIL - 5 - • • GEIL GX22GB6400DC 1024MB DS GEIL - 5 1.
DDR2-1066 (O.C.) MHz メモリースロット サポート (オプション) ベンダー パーツNo. サイズ SS/ DS チップ ブランド チップNO. タイミング 電圧 A-Data AD21066E001GOU 1024MB SS - Heat-Sink Package 5-5-5-15 - • • A-data AD21066E002GOU 2048MB DS - - 5-5-5-15 2.1V-2.3V • • CORSAIR TWIN2X40968500C5D G 4096MB(kit of 2) DS - - 5-5-5-15 2.10V • • CORSAIR TWIN2X40968500C7 G 4096MB(kit of 2) DS - - 7-7-7-20 2.00V • • Crucial BL12864AA1065.8FE5 1024MB SS - - - - • • G.
1.7.3 メモリーを取り付ける メモリーや、その他のシステムコンポーネントを追加、または取り外す前に、コンピューターの 電源プラグを抜いてください。プラグを差し込んだまま作業すると、マザーボードとコンポーネ ントが損傷する原因となります。 2 手順 1. フックを外側に押して、メモリースロット のロックを解除します。 2. メモリーのノッチがスロットの切れ目に 一致するように、メモリーをスロットに 合わせます。 メモリーノッチ 1 1 ロック解除されたフック メモリースロットキー メモリーは取り付ける向きがあります。間違った向きでメモリーを無理にスロットに差し込むと、 メモリーが損傷する原因となります。 3. メモリーの両端を指で支え、フックが所定 の場所に戻りメモリーが正しく取り付けら れるまで、メモリーをスロットにしっかり押 し込みます。 3 ロックされたフック 1.7.4 メモリーを取り外す 手順 1.
1.8 拡張スロット 拡張カードを取り付ける場合は、このページに書かれている拡張スロットに関する説明をお読み ください。 拡張カードの追加や取り外しを行う前に、電源コードを抜いてください。電源コー ドを接続したまま作業をすると、負傷や、マザーボードコンポーネントの損傷の原 因となります。 1.8.1 拡張カードを取り付ける 手順 1. 拡張カードを取り付ける前に、拡張カードに付属するマニュアルを読み、カードに必要なハ ードウェアの設定を行ってください。 2. コンピューターのケースを開けます(マザーボードをケースに取り付けている場合)。 3. カードを取り付けるスロットのブラケットを取り外します。ネジは後で使用するので、大切に 保管してください。 4. カードの端子部分をスロットに合わせ、カードがスロットに完全に固定されるまでしっかり 押します。 5. カードをネジでケースに固定します。 6. ケースを元に戻します。 1.8.2 拡張カードを設定する 拡張カードを取り付けた後、ソフトウェアの設定を行い拡張カードを使用できるようにします。 1.
1.9 1. ジャンパ Clear RTC RAM(3ピン CLRTC) このジャンパは、CMOSのリアルタイムクロック(RTC)RAMをクリアするものです。CMOS RTC RAMのデータを消去することにより、日、時、およびシステム設定パラメーターをクリアでき ます。システムパスワードなどのシステム情報を含むCMOS RAMデータの維持は、マザーボー ド上のボタン型電池により行われています。 2 2 3 CLRTC 1 P5G41C-M LX Normal (Default) Clear RTC P5G41C-M LX Clear RTC RAM RTC RAMをクリアする手順 1. コンピューターの電源をオフにし電源コードをコンセントから抜き、コイン型電池 (CMOS電池)を取り外します。 2. ジャンパキャップをピン 1-2(初期設定)からピン 2-3 に移動させます。5~10秒間その ままにして、再びピン1-2にキャップを戻します。 3. コイン型電池(CMOS電池)を取り付け、電源コードを差し込み、コンピューターの電源 をオンにします。 4.
2. キーボード電源 (3ピン KBPWR) キーボードのウェイクアップ機能を無効にします。このジャンパをピン2–3 (+5VSB)に設定 すると、キーボードの任意のキーを押すことでコンピューターをウェイクアップすることが できます。この機能を利用するには、+5V SBリード線で最低1Aを供給するATX電源を必 要とします。 KBPWR 1 2 3 2 +5VSB +5V (Default) P5G41C-M LX P5G41C-M LX Keyboard Power Setting 3.
1.10 コネクター 1.10.1 バックパネルコネクター 1 2 11 4 5 3 10 9 8 6 7 1. PS/2 マウスポート (グリーン) :PS/2 マウスを接続します。 2. パラレルポート:パラレルプリンター、スキャナー、その他のデバイスを接続します。 3. LAN(RJ-45)ポート:ネットワークハブを通して、LANでのGigabit 接続をサポートします。 LANポートLEDの表示内容は次の図をご参照ください。 LANポートLED ACT/LINK LED ACT/LINK スピード LED LED スピード LED 状態 説明 状態 説明 OFF リンクなし OFF 10 Mbps オレンジ リンク確立 オレンジ 100 Mbps 点滅 データ送受信中 グリーン 1 Gbps LANポート 4. ライン入力ポート (ライトブルー) :テープ、CD、DVDプレーヤー、またはその他のオーディオ ソースを接続します。 5.
7. USB 2.0 ポート1と2:USB 2.0デバイスを接続することができます。 8. USB 2.0 ポート3と4:USB 2.0デバイスを接続することができます。 9. VGAポート:VGAモニター等のVGAデバイスを接続します。 10. COM ポート:ポインティングデバイス、またはシリアルデバイス用です。 11. PS/2 キーボード(パープル) :PS/2 キーボード用です。 1.10.2 1.
2. IDEコネクター(40-1 ピン PRI_IDE) オンボード IDEケーブル用です。各Ultra DMA100/66/33ケーブルにはブルー、ブラック、グ レーの3つのコネクターがあります。マザーボードの IDEコネクターにはブルーを接続し、 下からいずれかのモードを選択してください。 ドライブジャンパ設定 デバイス1台 Cable-Select またはマスター Cable-Select デバイス2台 デバイスのモード - ケーブルコネクター ブラック マスター ブラック スレーブ グレー マスター マスター スレーブ スレーブ ブラックまたはグレー • IDEケーブルの接続方向誤りを防ぐため、Pin 20は取り外されています。 • Ultra DMA100/66/33 IDEデバイスの場合は、80芯の IDEケーブルを使用します。 PRI_IDE PIN1 P5G41C-M LX NOTE:Orient the red markings on the IDE ribbon cable to PIN 1.
3. ATX電源コネクター(24ピン EATXPWR、4ピン ATX12V) ATX電源プラグ用のコネクターです。電源プラグは正しい向きでのみ、取り付けられるよう に設計されています。正しい向きでしっかりと挿し込んでください。 GND GND +12V DC +12V DC ATX12V P5G41C-M LX EATXPWR +3 Volts +12 Volts +12 Volts +5V Standby Power OK GND PIN 1 +5 Volts GND +5 Volts GND +3 Volts +3 Volts GND +5 Volts +5 Volts +5 Volts -5 Volts GND GND GND PSON# GND -12 Volts +3 Volts PIN 1 P5G41C-M LX ATX power connectors • 容量 400W以上のATX 12 Version 2.
4. Serial ATAコネクター(7ピン SATA1-4) これらコネクターはSerial ATAケーブル用で、Serial ATA 3Gb/s 記憶装置に使用します。 Serial ATA 3Gb/sはSerial ATA 1.
6. CPU コネクター、ケースファンコネクター (4ピン CPU_FAN、3ピン CHA_FAN) ファンケーブルをマザーボードのファンコネクターに接続し、各ケーブルの黒いワイヤーが コネクターのアースピンに接続されていることを確認します。 PCケース内に十分な空気の流れがないと、マザーボードコンポーネントが破損する恐れがあります。 組み立ての際にはシステムの冷却ファン(吸/排気ファン)を必ず搭載してください。また、吸/排気フ ァン の電源をマザーボードから取得することで、エアフローをマザーボード側で効果的にコントロー ルすることができます。また、これはジャンパピンではありません。ファンコネクターにジャンパキャ ップを取り付けないでください。 CPU FAN PWM CPU FAN IN CPU FAN PWR GND CPU_FAN CHA_FAN P5G41C-M LX GND +12V Rotation P5G41C-M LX fan connectors ASUS Q-FAN 機能をサポートするのは、4ピンのCPUファンのみです。 7.
8.
1.11 ソフトウェア 1.11.1 OSをインストールする このマザーボードは Windows® XP/Vista / 7 OSをサポートしています。ハードウェアの機能を最 大限に活用するために、OSは定期的にアップデートしてください。 1.11.2 • ここで説明するセットアップ手順は一例です。詳細については、OSのマニュアルをご参照く ださい。 • 互換性とシステムの安定性のために、 ドライバーをインストールする前に、Windows® XPは Service Pack3 以降のサービスパック適用済みのOSであることをご確認ください。 サポートDVD情報 マザーボードに付属のサポートDVDには、マザーボードを利用するために必要なドライバー、ア プリケーション、ユーティリティが収録されています。 サポートDVDの内容は、予告なしに変更する場合があります。最新のものは、ASUS Webサイト (www.asus.co.
Chapter 2 BIOS情報 2.1 BIOS���� 管理更新 いつでもBIOSを復旧できるよう、オリジナルのマザーボードBIOSファイルをUSBフラッシュメ モリーにコピーしておいてください。BIOSのコピーにはASUS Update をご使用ください。 2.1.1 ASUS Update ASUS Update はWindows® 環境でマザーボードのBIOSの管理、保存、更新が可能です。 • ASUS Update を使用するには、インターネットアクセスが必要です。 • ASUS Update はマザーボードに付属のサポートDVDに収録されています。 ASUS Update をインストールする 手順 1. サポートDVDを光学ドライブに入れます。Drivers メニューが表示されます。 2. Utilities タブをクリックし、 「AI Suite II」をクリックします。 3. 画面の指示に従って、インストールを行います。 本ユーティリティでBIOS更新を行う場合は、Windows® アプリケーションを全て終了してから行 ってください。 BIOSを更新する 手順 1.
ASUS Update ユーティリティをインターネットから最新版に更新することができます。すべての 機能を利用できるよう、常に最新版をご使用ください。 BIOSファイルから更新する a. 「Update BIOS from a file」を選択し、 「Next」を選択します。 b. OpenダイアログからBIOSファイルを探し、 「Open」をクリックします。 3. 画面の指示に従い、更新作業を完了します。 2.1.2 ASUS EZ Flash 2 ASUS EZ Flash 2 はOSベースのユーティリティを使うことなく、BIOS更新を行います。 このユーティリティでBIOS更新を行う前に、ASUSのWeb サイト(http://www.asus.co.jp)から 最新バージョンのBIOSをダウンロードしてください。 EZ Flash 2 を使用してBIOSを更新する 1.
2.1.3 ASUS CrashFree BIOS ASUS CrashFree BIOS 3 はBIOSの自動復旧ツールで、BIOS更新時に障害を起こした場合や破損 したBIOSファイルを復旧します。破損したBIOSファイルはサポートDVD、またはBIOSファイルを保 存したUSBフラッシュドライブなどのリムーバブルディスクで更新することができます。 • このユーティリティを使用する前に、 リームバブルデバイスに保存したBIOSファイルの名前を 「P5G41TMU.ROM」に変更してください。 • サポートDVDに収録のBIOSファイルは最新バージョンではない場合があります。最新バージ ョンのBIOSファイルは弊社サイトにて公開しております。 http://www.asus.co.jp • ASUS CrashFree BIOSがサポートするリムーバブルデバイスはマザーボードにより異なりま す。フロッピーコネクター非搭載のマザーボードでは、USBフラッシュメモリーをご使用くだ さい。 BIOSを復旧する 手順 1. システムをONにします。 2.
2.
2.2.1 BIOSメニュー画面 メニュー Main メニューバー Advanced Power System Time System Date Primary IDE Master Primary IDE Slave SATA 1 SATA 2 SATA 3 SATA 4 構成フィールド ヘルプ BIOS SETUP UTILITY Boot Tools Exit [00:31:48] [Tue 01/01/2002] :[Not :[Not :[Not :[Not :[Not :[Not Detected] Detected] Detected] Detected] Detected] Detected] Storage Configuration System Information Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system Time.
2.2.3 ナビゲーションキー BIOSメニュー画面の右下には、メニューの操作をするためのナビゲーションキーの説明が表示さ れています。ナビゲーションキーを使用してメニューの項目を選択し、設定を変更します。 掲載したBIOS画面は参考で、実際に表示される内容と異なる場合があります。 2.2.4 メニュー メニューバーをハイライト表示すると、そのメニューの設定項目が表示されます。例えば、メイン を選択するとメインのメニューが表示されます。 メニューバーの他の項目(Advanced、Power、Boot、Tools、Exit) には、それぞれのメニューがあり ます。 2.2.5 サブメニュー サブメニューが含まれる項目の前には、黒い三角形が付いています。サブメニューを表示するた めには、項目を選択し を押します。 2.2.
2.3 メインメニュー BIOS Setup に入るとメインメニューが表示され、システム情報の概要が表示されます。 メニュー画面の情報および操作方法については、 「2.2.1 BIOS メニュー画面」をご参照くだ さい。 Main Advanced Power System Time System Date Primary IDE Master Primary IDE Slave SATA 1 SATA 2 SATA 3 SATA 4 BIOS SETUP UTILITY Boot Tools Exit [12:56:38] [Tue 01/01/2002] :[Not :[Not :[Not :[Not :[Not :[Not Detected] Detected] Detected] Detected] Detected] Detected] Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time.
LBA/Large Mode [Auto] LBA(Logical Block Addressing)モードの有効/無効を設定します。自動的にデバイスがLBAモー ドをサポートしているかどうかを検出し、サポートしている場合はLBAモードが有効になります。 デバイスがLBAモードでフォーマットされていない場合は無効にします。 設定オプション:[Disabled] [Auto] Block (Multi-sector Transfer) M [Auto] マルチセクター転送の有効/無効を設定します。[Auto] に設定すると、デバイスがマルチセク ター転送機能をサポートしていれば、デバイス間のデータ転送をマルチセクターで行います。 [Disabled] に設定すると、デバイス間のデータ転送は1セクタごとに行います。 設定オプション:[Disabled] [Auto] PIO Mode [Auto] PIOモードを設定します。 設定オプション:[Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] DMAモードを設定します。 設定オプション:[Auto] SMART M
2.3.5 システム情報 システム仕様の概要を表示します。BIOSはBIOSに関する情報やCPUの仕様、システムメモリー等の 情報を自動的に検出します。 BIOS Information BIOS情報を自動検出し表示します。 Processor CPUの仕様を自動検出し表示します。 System Memory システムメモリーを自動検出し表示します。 2.4 拡張メニュー CPUとその他のシステムデバイスの設定を変更します。 拡張メニューの設定変更は、システムの誤動作の原因となることがあります。ご注意ください。 Main Advanced Power BIOS SETUP UTILITY Boot Tools Exit JumperFree Configuration CPU Configuration Chipset Onboard Devices Configuration USB Configuration PCIPnP 2.4.1 Adjust System frequency/voltage.
次の2項目は「AI Overclocking」を [MANUAL] にすると表示されます。 CPU Frequency [xxx] クロック発振器からシステムと PCI に送られる周波数を表示します。この数値はBIOSにより 自動検出されます。CPU周波数を調節する際は、<+> と <-> キーを使用します。また、直接 数字キーで入力することもできます。 設定範囲は 200 〜 800です。次の表はFSB周波数とCPU外部動作周波数の適正値です。 FSB / CPU外部周波数の同期 FSB周波数 CPU外部動作周波数 FSB 1333 333 MHz FSB 1066 266 MHz FSB 800 200 MHz PCI Express Frequency [Auto] PCI Express 周波数を選択します。 設定オプション:[Auto] [90] [91] [92]~[150] 次の項目は「AI Overclocking」を [Overclock Profile] にすると表示されます。 Overclock Options [Overclock 5%] オーバークロックのオ
Memory Voltage [Auto] メモリーの電圧を設定します。設定範囲は 1.2000V 〜 2.4450Vです。数値は直接入力するか、 <+> キーで 0.0150V刻み、または<-> キーで 0.0750V刻みで調節します。 設定オプション:[Auto] NB Voltage [Auto] ノースブリッジの電圧を設定します。設定範囲は 1.12500Vから 1.51875Vで、0.00625V刻みで調 節します。数値の調節は <+> <-> キー、または数字キーで直接入力します。 設定オプション:[Auto] VTT Voltage [Auto] VTTの電圧を設定します。設定範囲は 1.20000Vから1.29375Vで、0.00625V刻みで調節します。数 値の調節は <+> <-> キー、または数字キーで直接入力します。 設定オプション:[Auto] SB 1.5V Voltage [Auto] サウスブリッジ電圧を調節します。 設定オプション:[1.5V] [1.
CPU TM Function [Enabled] Intel® CPU Thermal Monitor (TM) 機能の有効/無効を設定します。オーバーヒートしたCPUのコ ア周波数と電圧を抑えることで冷却を図ります。 設定オプション:[Disabled] [Enabled] Execute-Disable Bit Capability [Enabled] No-Execution Page Protection Technology の有効/無効を設定します。[Disabled] にすると、 XD機能フラグが常にゼロ(0)に戻ります。 設定オプション:[Disabled] [Enabled] 次の項目は Enhanced Intel SpeedStep® Technology(EIST)をサポートする Intel® Pentium® 4 以降のCPUを取り付けると表示されます。 Intel(R) SpeedStep(TM) Tech [Enabled] [Enabled] にすると、EIST機能によりOS環境でシステム電源設定を調節できます。EIST機能を使 用しない場合は [Disabled] にし
DVMT Memory [256MB] DVMTメモリーを選択します。 設定オプション:[128MB] [256MB] [Maximum DVMT] Protect Audio Video Path Mode [Lite] Protected Audio-Video Path(PAVP)モードの設定を行います。 設定オプション:[Disabled] [Lite] [Paranoid] South Bridge Configuration Audio Controller [Enabled] オーディオコントローラーを設定します。 設定オプション:[Enabled] [Disabled] Front Panel Type [HD Audio] フロントパネルのサポートタイプを選択します。HDオーディオフロントパネルを使用する 際は、[HD Audio] を選択します。 設定オプション:[AC97] [HD Audio] 2.4.
2.4.5 USB設定 USBに関連する機能の設定変更を行います。項目を選択し を押すと設定オプションが表 示されます。 「Module Version」 と 「USB Devices Enabled」の項目には自動検出された値が表示されます。 USBデバイスが接続されていない場合は、[None] と表示されます。 USB Functions [Enabled] USBの各機能の有効/無効を設定します。 設定オプション:[Disabled] [Enabled] USB 2.0 Controller [Enabled] USB 2.
2.4.6 PCI PnP PCI PCI/PnPデバイスの設定を変更します。このメニューではPCI/PnPデバイスまたはレガシー ISAデバイス用の IRQとDMAチャンネルリソースの設定と、レガシー ISAデバイス用のメモリーサ イズブロックの設定が可能です。 PCI PnPメニューの各項目に誤った数値を選択すると、システムの誤作動の原因となります。設 定変更の際はご注意ください。 Plug and Play O/S [No] [No] にすると、システム内の全てのデバイスがBIOSにより構成されます。Plug and Play OSをイ ンストールしている状態で [Yes] にすると、起動に不要な Plug and Play デバイスは全てOSによ り構成されます。 設定オプション:[No] [Yes] 2.5 ������ 電源メニュー ACPI とAPM機能の設定の変更を行います。項目を選択し、を押すと設定オプションが表 示されます。 Main Advanced Power Suspend Mode ACPI 2.
2.5.
CPU Fan Profile [Optimal Mode] CPU Q-Fan コントロール機能を有効にすると、この項目が表示されます。CPUファンを適切なパフ ォーマンスレベルに設定することができます。 設定オプション:[Optimal Mode] [Silent Mode] [Performance Mode] Chassis Fan Speed [xxxxRPM] 又は [Ignored] Tオンボードハードウェアモニターは、自動的にケースファンの速度を検出し、回転速度を分単位 (RPM)で表示します。ファンがマザーボードに接続されていない場合は、 「N/A」 と表示されます。 検出速度を表示する必要がない場合は、 「Ignored」を選択します。 VCORE Voltage、3.3V Voltage、5V Voltage、12V Voltage [xxxV] 又は [Ignored] オンボード電圧レギュレータを通じ、自動的に電圧出力を検出して表示します。 2.
Full Screen Logo [Enabled] フルスクリーンロゴの表示/非表示を切り替えます。 設定オプション:[Disabled] [Enabled] ASUS MyLogo 2™ 機能をご利用になる場合は「Full Screen Logo」の項目を [Enabled] に設定 してください。 AddOn ROM Display Mode [Force BIOS] オプションROMに対するディスプレイのモードを設定します。 設定オプション:[Force BIOS] [Keep Current] Bootup Num-Lock [On] 電源をオンにしたときの、NumLock の状態を選択します。 設定オプション:[Off] [On] Wait For ‘F1’ If Error [Enabled] [Enabled] に設定するとシステムはエラー発生時に キーを押すまで待機します。 設定オプション:[Disabled] [Enabled] Hit ‘DEL’ Message Display [Enabled] [Enabled] に設定すると、POST中に「Press DE
管理者パスワードを設定すると、他のセキュリティ設定を変更するための項目が表示されます。 User Access Level [Full Access] BIOSメニューへのアクセス制限の選択を行います。 設定オプション:[No Access] [View Only] [Limited] [Full Access] [No Access] - BIOS Setup へのユーザーのアクセスを拒否します。 [View Only] - アクセスは許可しますが設定の変更はできません。 [Limited] - 日時など、限られた設定のみを変更することができます。 [Full Access] - 全ての項目を表示、変更することができます。 Change User Password ユーザーパスワードの設定または変更をします。画面上部に表示されている「User Password」 は初期設定値では「Not Installed」になっています。パスワードを設定すると、 「Installed」に変更 されます。 ユーザーパスワードの設定手順 1.
2.7 ツールメニュー スペシャル機能のオプション設定をします。項目を選択し を押してサブメニューを表示 させます。 Main Advanced Power BIOS SETUP UTILITY Boot Tools Exit ASUS EZ Flash 2 Express Gate Enter OS Timer Reset User Data [Auto] [10 Seconds] [No] AI NET 2 2.7.1 Press ENTER to run the utility to select and update BIOS. This utility supports 1.FAT 12/16/32 (r/w) 2.NTFS (read only) 3.CD-DISC (read only) ASUS EZ Flash 2 ASUS EZ Flash 2 を起動します。を押すと、確認メッセージが表示されます。左右矢 印キーを使って [Yes] または [No] を選択し を押して選択を決定します。詳細はセク ション 2.1.
2.8 終了メニュー BIOS 設定の保存や取り消しのほか、初期設定値のロードを行います。 Main Advanced Power Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Load Setup Defaults BIOS SETUP UTILITY Boot Tools Exit Exitsystem systemsetup setup Exit aftersaving savingthe the after changes. changes. F10key keycan canbe beused used F10 forthis thisoperation. operation.
2-22 Chapter 2: BIOS情報
ASUSコンタクトインフォメーション ASUSTeK COMPUTER INC. 住所: 電話(代表) : ファックス(代表) : 電子メール(代表) : Webサイト: テクニカルサポート 電話: オンラインサポート: 15 Li-Te Road, Beitou, Taipei, Taiwan 11259 +886-2-2894-3447 +886-2-2890-7798 info@asus.com.tw www.asus.com.tw +86-21-3842-9911 support.asus.com ASUS COMPUTER INTERNATIONAL(アメリカ) 住所: 電話: ファックス: Webサイト: テクニカルサポート 電話: サポートファックス: オンラインサポート: 800 Corporate Way, Fremont, CA 94539, USA +1-510-739-3777 +1-510-608-4555 http://usa.asus.com +1-812-282-2787 +1-812-284-0883 support.asus.
(510)739-3777/(510)608-4555 800 Corporate Way, Fremont, CA 94539. Asus Computer International Signature : Date : Representative Person’s Name : Jan. 12, 2010 Steve Chang / President This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.