User Manual
Table Of Contents
- 目錄內容
- 第一章:產品介紹
- 1.12 關閉電源
- 1.11 第一次啟動電腦
- 1.10 元件與外圍設備的連接
- 1.9 跳線選擇區
- 1.8 擴展插槽
- 1.7 系統內存
- 1.6 中央處理器(CPU)
- 1.5 主板概述
- 1.4 主板安裝前
- 1.3 特殊功能
- 1.2 產品包裝
- 1.1 歡迎加入華碩愛好者的行列!
- 第二章:BIOS 程序設置
- 2.8 退出 BIOS 程序(Exit menu)
- 2.7 工具菜單(Tools menu)
- 2.6 啟動菜單(Boot menu)
- 2.5 電源管理(Power menu)
- 2.4 高級菜單(Advanced menu)
- 2.3 主菜單(Main Menu)
- 2.2 BIOS 程序設置
- 2.1 管理、升級您的 BIOS 程序
- 第三章:軟件支持
- 3.3 軟件信息
- 3.2 驅動及應用程序光盤信息
- 3.1 安裝操作系統
2-31
華碩 P5G43-V WS 主板用戶手冊
User Access Level [Full Access]
本項目可讓您選擇 BIOS 程序存取限制權限等級。設置值有:[No Access]
[View Only] [Limited] [Full Access]。
No Access 用戶無法存取 BIOS 程序。
View Only 允許用戶讀取 BIOS 程序但無法更改任何項目。
Limited 允許用戶只能存取 BIOS 程序的某些項目。例如:系統
時間。
Full Access 允許用戶存取完整的 BIOS 程序。
Change User Password(更改用戶密碼)
本項目是用於更改用戶密碼,運行狀態會於畫面上方以淡灰色顯示,默認
值為 Not Installed。當您設置密碼後,則此項目會顯示 Installed。
設置用戶密碼(User Password):
1. 選擇 Change User Password 項目並按下 <Enter> 鍵。
2. 在 Enter Password 窗口出現時,請輸入欲設置的密碼,可以是六個字節
內的英文、數字與符號。輸入完成按下 <Enter>。
3. 接著會再出現 Confirm Password 窗口,再一次輸入密碼以確認密碼正
確。密碼確認無誤時,系統會出現 Password Installed. 信息,代表密碼
設置完成。若出現 Password do not match! 信息,代表於密碼確認時輸
入錯誤,請重新輸入一次。此時畫面上方的 User Password 項目會顯示
Installed。
若要更改用戶的密碼,請依照上述程序再運行一次密碼設置。
Clear User Password(清除用戶密碼)
請選擇本項目來清除用戶密碼。
Password Check [Setup]
當您將本項目設為 [Setup],BIOS 程序會於用戶進入 BIOS 程序設置畫面
時,要求輸入用戶密碼。若設為 [Always] 時,BIOS 程序會在啟動過程亦要
用戶輸入密碼。設置值有:[Setup] [Always]
Select Screen
Select Item
Enter Change
F1 General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2006, American Megatrends, Inc.
Security Settings
Supervisor Password : Not Installed
User Password : Not Installed
Change Supervisor Password
User Access Level [Full Access]
Change User Password
Clear User Password
Password Check [Setup]
<Enter> to change
password.
<Enter> again to
disabled password.
BIOS SETUP UTILITY
Boot