Motherboard P5GDC-V Deluxe
E1716 Revised Edition V2 July 2004 Copyright © 2004 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Notices ............................................................................................... vii Safety information ............................................................................ viii Operation safety ............................................................................... viii P5GDC-V Deluxe specifications summary ........................................... ix Chapter 1: Product introduction 1.1 Welcome! ..........................................................
Contents 2.5.5 PCI Express x1 slot ............................................... 2-23 2.5.6 PCI Express x16 slot ............................................. 2-23 2.6 Jumpers .............................................................................. 2-24 2.7 Connectors ......................................................................... 2-27 2.7.1 Rear panel connectors .......................................... 2-27 2.7.2 Internal connectors ............................................
Contents 4.4 4.5 4.6 4.7 4.3.5 IDE Configuration .................................................. 4-15 4.3.6 System Information .............................................. 4-17 Advanced menu .................................................................. 4-18 4.4.1 JumperFree Configuration .................................... 4-18 4.4.2 LAN Cable Status ................................................. 4-22 4.4.3 USB Configuration .................................................
Contents 5.4 5.5 vi RAID configurations ............................................................ 5-16 5.4.1 Installing hard disks .............................................. 5-17 5.4.2 Intel® RAID configurations .................................... 5-18 5.4.3 ITE® 8212F RAID configurations ........................... 5-22 Creating a RAID driver disk .................................................
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
P5GDC-V Deluxe specifications summary CPU LGA775 socket for Intel® Pentium® 4/Celeron processor Compatible with Intel® PCG 04A and 04B processors Supports Intel® Hyper-Threading Technology Chipset Northbridge: Intel® 915G Graphics Memory Controller Hub (GMCH) Southbridge: Intel® ICH6R Front Side Bus 800/533 MHz Memory Dual-channel memory architecture 2 x 240-pin DIMM sockets support unbufferred non-ECC 2 GB 600/533/400 MHz DDR2 memory modules 4 x 184-pin DIMM sockets support unbufferred non-ECC 4 GB
P5GDC-V Deluxe specifications summary Overclocking features ASUS AI NOS™ (Non-delay Overclocking System) ASUS AI Overclocking ASUS C.P.R.
This chapter describes the motherboard features and the new technologies it supports.
Chapter summary 1 1.1 Welcome! .............................................................................. 1-1 1.2 Package contents ................................................................. 1-1 1.3 Special features ....................................................................
1.1 Welcome! T h a n k y o u f o r b u y i n g a n A S U S® P 5 G D C - V D e l u x e m o t h e r b o a r d ! The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your motherboard package for the following items.
1.3 Special features 1.3.1 Product highlights Latest processor technology The motherboard comes with a 775-pin surface mount Land Grid Array (LGA) socket designed for the Intel® Pentium® 4 processor in the 775-land package. The motherboard supports the Intel® Pentium® 4 processor with 800/533 MHz Front Side Bus (FSB). The motherboard also supports the Intel® Hyper-Threading technology and is fully compatible with Intel® 04B and 04A processors. See page 2-7 for details.
Dual-channel DDR and DDR2 memory support The motherboard supports DDR and DDR2 memory for flexible system upgrade and to meet the higher bandwidth requirements of the latest 3D graphics, multimedia, and Internet applications. The dual-channel architecture allows memory bandwidths of up to 6.4 GB/s for DDR, or 8.5 GB/s for DDR2. See page 2-13 for details. PCI Express™ interface The motherboard fully supports PCI Express, the latest I/O interconnect technology that speeds up the PCI bus.
Dual RAID solution Onboard RAID controllers provide the motherboard with dual-RAID functionality that allows you to select the best RAID solution using IDE or Serial ATA devices. The Intel® ICH6R allows RAID 0 and RAID 1 configuration for four Serial ATA connectors and supports the Intel® Matrix Storage Technology. See page 2-30 for details.
ASUS Stack Cool™ ASUS Stack Cool™ is an ideal thermal solution that reduces the heat dissipated by large capacitors and motherboard components. By placing a specially designed PCB under the CPU socket, Stack Cool™ effectively lowers the system temperature by 10º Celsius. Cooler system temperature means more stable system performance, longer component life, and more silent operation. See page 2-3 for details.
1.3.3 Innovative ASUS features ASUS Q-Fan 2 technology The ASUS Q-Fan 2 technology smartly adjusts the CPU and chassis fan speeds according to the system loading to ensure quiet, cool, and efficient operation. See page 4-34 for details. ASUS CrashFree BIOS 2 This feature allows you to restore the original BIOS data from the support CD in case when the BIOS codes and data are corrupted. This protection eliminates the need to buy a replacement ROM chip. See page 4-5 for details.
This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
Chapter summary 2 2.1 Before you proceed .............................................................. 2-1 2.2 Motherboard overview .......................................................... 2-2 2.3 Central Processing Unit (CPU) .............................................. 2-7 2.4 System memory ................................................................. 2-13 2.5 Expansion slots ................................................................... 2-21 2.6 Jumpers ........................
2.1 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Use a grounded wrist strap or touch a safely grounded object or to a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity • Hold components by the edges to avoid touching the ICs on them.
2.2 Motherboard overview Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components. 2.2.1 Placement direction When installing the motherboard, make sure that you place it into the chassis in the correct orientation.
2.2.3 ASUS Stack Cool™ The motherboard comes with ASUS Stack Cool™, an innovative thermal solution that provides supplementary cooliing to the motherboard. Stack Cool™ is a mini-PCB installed under the CPU socket to conduct heat away from the motherboard components. Stack Cool™ effectively lowers the motherboard temperature by as much as 10ºC.
2.2.4 Motherboard layout 24.5cm (9.6in) KBPWR1 PS/2KBMS T: Mouse B: Keyboard ATX12V Intel MCH 915G PWR_FAN1 EATXPWR PRI_IDE1 Top:Line In Center:Line Out Below:Mic In 30.5cm (12.
2.2.5 Layout Contents Slots Page 1. DDR DIMM slots 2-13 2. PCI slots 2-23 3. PCI Express slots 2-23 Jumpers Page 1. Clear RTC RAM (3-pin CLRTC1) 2-24 2. USB Device wake-up (3-pin USBPW12, USBPW34, USBPW56, USBPW78) 2-25 3. Keyboard power (3-pin KBPWR1) 2-26 Rear panel connectors Page 1. PS/2 mouse port 2-27 2. Parallel port 2-27 3. IEEE 1394a port 2-27 4. LAN (RJ-45) port 2-27 5. Rear Speaker Out port 2-27 6. Side Speaker Out port 2-27 7. Line In port 2-27 8.
2-6 Internal connectors Page 1. Floppy disk drive connector (34-1 pin FLOPPY) 2-29 2. Primary IDE connector (40-1 pin PRI_IDE) 2-29 3. Primary IDE RAID connector (40-1 pin PRI_RAID) 2-30 4. Secondary IDE RAID connector (40-1 pin SEC_RAID) 2-31 5. Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4) 2-31 6. CPU fan connector (4-pin CPU_FAN) 2-32 7. Chassis fan connectors (3-pin CHA_FAN1, CHA_FAN2) 2-32 8. Power fan connector (3-pin PWR_FAN) 2-32 9.
2.3 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA775 socket designed for the Intel® Pentium® 4 processor in the 775-land package. 2.3.1 • Upon purchase of the motherboard, make sure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components.
2. Press the load lever with your thumb and move it to the left until it is released from the retention tab. PnP Cap Retention tab A Load lever This side of the socket box should face you. B To prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU. 3. Lift the load lever in the direction of the arrow to a 135º angle. 4. Lift the load plate with your thumb and forefinger to a 100º angle (A), then push the PnP cap from the load plate window to remove (B).
5. Position the CPU over the socket, making sure that the gold triangle is on the bottom-left corner of the socket. The socket alignment key should fit into the CPU notch. 6. Close the load plate (A), then push the load lever (B) until it snaps into the retention tab. A B Alignment key Gold triangle mark The CPU fits in only one correct orientation.
To use the Hyper-Threading Technology on this motherboard: 1. Install an Intel® Pentium® 4 CPU that supports Hyper-Threading Technology. 2. Power up the system and enter the BIOS Setup (see Chapter 4: BIOS setup). Under the Advanced Menu, make sure that the item Hyper-Threading Technology is set to Enabled. The item appears only if you installed a CPU that supports Hyper-Threading Technology. 3. Reboot the computer. 2.3.
To install the CPU heatsink and fan: 1. Place the heatsink on top of the installed CPU, making sure that the four pins match the holes on the motherboard. Push pin Motherboard hole 2. Push each of the pins downward to secure the heatsink and fan assembly in place. ASUS P5GDC-V Deluxe 3. Rotate the push-pins clockwise to lock.
4. When the fan and heatsink assembly is in place, connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN1. P5GDC-V GND CPU FAN PWR CPU FAN IN CPU FAN PWM CPU_FAN1 Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector.
2.4 System memory 2.4.1 Overview The motherboard comes with two 240-pin Double Data Rate (DDR2) and four 184-pin DDR Dual Inline Memory Modules (DIMM) sockets. DDR2 DIMMS are notched differently to prevent installation on a DDR DIMM socket. The following figure illustrates the location of the sockets: DDR_B1 DDR_B2 DDR2_B1 DDR2_A1 P5GDC-V P5GDC-V DIMM sockets DDR_A2 DDR_A1 To prevent damage to the motherboard, d o n o t u s e D D R a n d D D R 2 memory simultaneously. 2.4.
Recommended DDR memory configurations For dual-channel configuration, the total size of memory module(s) installed per channel must be the same to ensure optimum performance.
DDR (400 MHz) Qualified Vendors List DIMM support (optional) Size Vendor Model Brand Side/s* Component A B C 256MB GEIL GE2563200B GEIL SS GL3LC32G88TG-5A • • • 512MB GEIL GE5123200B GEIL DS GL3LC32G88TG-5A • 256MB GEIL GD3200-256V GEIL SS GLIL DDR 32M8 • • • 512MB GEIL GD3200-512V GEIL DS GLIL DDR 32M8 • • 256MB TwinMOS M2S9I08AFAPS9F0811A-T PSC SS A2S56D30ATP • • • 256MB TwinMOS M2G9I08AIATT9F081AADT TwinMOS SS TMD7608F8E50D • • • 512MB TwinMOS M2G9J16AJ
DDR (400 MHz) Qualified Vendors List DIMM support (optional) Size Vendor Model Brand Side/s* Component A B C 256MB CENTURY DXV6S8SSCCD3K27C SAMSUNG SS K4H560838D-TCCC • • • 512MB CENTURY DXV2S8SSCCD3K27C SAMSUNG DS K4H560838D-TCCC • • 256MB CENTURY DXV6S8SSCCE3K27E SAMSUNG SS K4H560838E-TCCC • • • 512MB CENTURY DXV2S8SSCCE3K27E SAMSUNG DS K4H560838E-TCCC • • • 256MB CENTURY DXV6S8MC5BC3U27E MICRON SS MT46V32M8TG-5BC • • • 512MB CENTURY DXV2S8MC5BC3U27E MICRON D
DDR2 (533MHz) Qualified Vendors List DIMM support (optional) Size Model Brand SAMSUNG M378T6553BG0-CD5 N/A SS 1024MB SAMSUNG M378T2953BG0-CD5 N/A 256MB SAMSUNG M378T3253FG0-CD5 512MB SAMSUNG 512MB Infineon 512MB 512MB 512MB Vendor Side/s* Component A B K4T51083QB-GCD5 • • DS K4T51083QB-GCD5 • • N/A SS K4T56083QF-GCD5 • • M378T6453FG0-CD5 N/A DS K4T56083QF-GCD5 • • HYS64T64000GU-3.
DDR2-533 with 600 MHz capability (overclocking) DIMM support (optional) Size Model Brand SAMSUNG M378T6553BG0-CD5 N/A SS 1024MB SAMSUNG M378T2953BG0-CD5 N/A DS 512MB Vendor Side/s* Component A B K4T51083QB-GCD5 • • K4T51083QB-GCD5 • • 256MB SAMSUNG M378T3253FG0-CD5 N/A SS K4T56083QF-GCD5 • • 512MB SAMSUNG M378T6453FG0-CD5 N/A DS K4T56083QF-GCD5 • • 512MB Infineon HYS64T64000GU-3.
2.4.3 Installing a DDR DIMM Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components. 2 1. Unlock a DIMM socket by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. DDR DIMM notch 1 1 Unlocked retaining clip A DDR DIMM is keyed with a notch so that it fits in only one direction.
2.4.5 Installing a DDR2 DIMM Unplug the power supply before adding or removing DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components. 2 To install a DIMM: 1. Unlock a DIMM socket by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. 3.
2.5 Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. 2.5.1 Installing an expansion card To install an expansion card: 1.
2.5.
2.5.4 PCI slots The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The figure shows a LAN card installed on a PCI slot. 2.5.6 2.5.5 slot PCI Express x1 This motherboard supports PCI Express x1 network cards, SCSI cards and other cards that comply with the PCI Express specifications. The figure shows a network card installed on the PCI Express x1 slot.
2.6 1. Jumpers Clear RTC RAM (CLRTC1) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the onboard battery. 3.
2. USB device wake-up (3-pin USBPW12, USBPW34, USBPW56, USBPW78) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode). The USBPWR12 and USBPWR34 jumpers are for the rear USB ports.
3. Keyboard power (3-pin KBPWR) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) to wake up the computer when you press a key on the keyboard (the default is the Space Bar). This feature requires an ATX power supply that can supply at least 1A on the +5VSB lead, and a corresponding setting in the BIOS.
2.7 Connectors 2.7.1 Rear panel connectors 1 2 3 4 5 6 7 8 9 16 1. 2. 3. 4. 15 14 13 12 11 10 P S / 2 m o u s e p o r t ( g r e e n ) . This port is for a PS/2 mouse. P a r a l l e l p o r t . This 25-pin port connects a parallel printer, a scanner, or other devices. I E E E 1 3 9 4 a p o r t . This 6-pin port provides high-speed connectivity for audio/video devices, storage peripherals, PCs, or portable devices. L A N ( R J - 4 5 ) p o r t .
9 . M i c r o p h o n e p o r t ( p i n k ) . This port connects a microphone. 1 0 . C e n t e r / S u b w o o f e r p o r t ( y e l l o w o r a n g e ) . This port connects the center/subwoofer speakers. Refer to the audio configuration table for the function of the audio ports in 2, 4, 6, or 8-channel configuration.
2.7.2 1. Internal connectors Floppy disk drive connector (34-1 pin FLOPPY1) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. Pin 5 on the connector is removed to prevent incorrect cable connection when using an FDD cable with a covered Pin 5. P5GDC-V FLOPPY1 PIN 1 NOTE: Orient the red markings on the floppy ribbon cable to PIN 1.
3. IDE RAID connectors (40-1 pin PRI_RAID1 [red], SEC_RAID1 [red]) These connectors are for Ultra ATA 133/100/66 signal cables. These connectors support up to four IDE hard disk drives that can be configured as a disk array through the onboard IDE RAID controller. These connectors are set to IDE mode by default. In IDE mode, you can connect IDE devices to these connectors such as boot/data hard disk drives or optical drives.
4. Serial ATA connectors (7-pin SATA1 [red], SATA2 [red], SATA3 [black], SATA4 [black]) These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives. If you installed Serial ATA hard disk drives, you can can create a RAID 0 or RAID 1 configuration with the Intel® Matrix Storage Technology through the onboard Intel® ICH6R RAID controller. Refer to Chapter 5 for information on creating a RAID configuration. These connectors are set to Standard IDE configuration by default.
5. CPU, Chassis, and Power fan connectors (4-pin CPU_FAN, 3-pin PWR_FAN, 3-pin CHA_FAN1, 3-pin CHA_FAN2) The fan connectors support cooling fans of 350 mA ~ 2000 mA (24 W max.) or a total of 1 A ~ 3.48 A (41.76 W max.) at +12 V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. CPU_FAN1 GND CPU FAN PWR CPU FAN IN CPU FAN PWM Do not forget to connect the fan cables to the fan connectors.
6. Serial port connector (10-1 pin COM1) This connector is for a serial (COM) port. Connect the serial port module cable to this connector, then install the module to a slot opening at the back of the system chassis. COM1 P5GDC-V PIN 1 P5GDC-V Serial port connector USB connectors (10-1 pin USB56, USB78) These connectors are for USB 2.0 ports. Connect the USB/GAME module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis.
8. ATX power connectors (24-pin EATXPWR, 4-pin ATX12V) These connectors are for an ATX power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. • We recommend that you use an ATX 12 V Specification 2.0-compliant power supply unit (PSU) with a minimum of 350 W power rating. This PSU type has 24-pin and 4-pin power plugs.
9. Optical drive audio connector (4-pin CD) P5GDC-V P5GDC-V CD audio connector Right Audio Channel Ground Ground Left Audio Channel This connector is for the 4-pin audio cable that connects to the audio connector at the back of the optical drive. CD 1 0 . GAME/MIDI port connector (16-1 pin GAME) This connector is for a GAME/MIDI port. Connect the USB/GAME module cable to this connector, then install the module to a slot opening at the back of the system chassis.
1 1 . Chassis intrusion connector (4-1 pin CHASSIS) This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. The signal is then generated as a chassis intrusion event. By default, the pins labeled “Chassis Signal” and “Ground” are shorted with a jumper cap.
1 2 . Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC ‘97 audio standard. Connect one end of the front panel audio I/O module cable to this connector.
1 4 . System panel connector (20-pin PANEL) This connector supports several chassis-mounted functions. +5V Ground Ground Speaker SPEAKER IDE_LED Reset Ground PWR Ground PANEL1 IDE_LED+ IDE_LED- P5GDC-V PLED- PLED+ PLED Reset PWRSW P5GDC-V System panel connector The sytem panel connector is color-coded for easy connection. Refer to the connector description below for details. • • • • • 2-38 System power LED (Green 3-pin PLED) This 3-pin connector is for the system power LED.
This chapter describes the power up sequence, the vocal POST messages, and ways of shutting down the system.
Chapter summary 3 3.1 Starting up for the first time ................................................ 3-1 3.2 Powering off the computer ..................................................
3.1 Starting up for the first time 1. After making all the connections, replace the system case cover. 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: a. Monitor b. External SCSI devices (starting with the last device on the chain) c. System power 6.
3.2 Powering off the computer 3.2.1 Using the OS shut down function If you are using Windows® 2000: 2. Click the S t a r t button then click S h u t D o w n . . . Make sure that the S h u t D o w n option button is selected, then click the O K button to shut down the computer. 3. The power supply should turn off after Windows® shuts down. 1. If you are using Windows® XP: 2. Click the S t a r t button then select T u r n O f f C o m p u t e r .
This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
Chapter summary 4 4.1 Managing and updating your BIOS ........................................ 4-1 4.2 BIOS setup program ........................................................... 4-10 4.3 Main menu .......................................................................... 4-13 4.4 Advanced menu .................................................................. 4-18 4.5 Power menu ........................................................................ 4-31 4.6 Boot menu .....................
4.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. 2. ASUS floppy ASUS A F U D O S (Updates the BIOS in DOS mode using a bootable disk.) E Z F l a s h (Updates the BIOS using a floppy disk during POST.) 3. A S U S C r a s h F r e e B I O S 2 (Updates the BIOS using a bootable floppy disk or the motherboard support CD when the BIOS file fails or gets corrupted.) 4.
d. From the Open field, type D:\bootdisk\makeboot a: assuming that D: is your optical drive. e. Press , then follow screen instructions to continue. 2. Copy the original or the latest motherboard BIOS file to the bootable floppy disk. 4.1.2 ASUS EZ Flash utility The ASUS EZ Flash feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS-based utility.
4.1.3 AFUDOS utility The AFUDOS utility allows you to update the BIOS file in DOS environment using a bootable floppy disk with the updated BIOS file. This utility also allows you to copy the current BIOS file that you can use as backup when the BIOS fails or gets corrupted during the updating process. Copying the current BIOS To copy the current BIOS file using the AFUDOS utility: • Make sure that the floppy disk is not write-protected and has at least 600 KB free space to save the file.
Updating the BIOS file To update the BIOS file using the AFUDOS utility: 1. Visit the ASUS website (www.asus.com) and download the latest BIOS file for the motherboard. Save the BIOS file to a bootable floppy disk. Write the BIOS filename on a piece of paper. You need to type the exact BIOS filename at the DOS prompt. 2. Copy the AFUDOS utility (afudos.exe) from the motherboard support CD to the bootable floppy disk you created earlier. 3.
5. The utility returns to the DOS prompt after the BIOS update process is completed. Reboot the system from the hard disk drive. A:\>afudos /iP5GDCVD.ROM AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB)) Copyright (C) 2003 American Megatrends, Inc. All rights reserved. WARNING!! Do not turn off power during flash BIOS Reading file ..... done Reading flash ....
3. The utility displays the following message and automatically checks the floppy disk for the original or updated BIOS file. Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... When found, the utility reads the BIOS file and starts flashing the corrupted BIOS file. Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Floppy found! Reading file “P5GDCVD.ROM”. Completed. Start flashing...
DO NOT shut down or reset the system while updating the BIOS! Doing so can cause system boot failure! 4. Restart the system after the utility completes the updating process. The recovered BIOS may not be the latest BIOS version for this motherboard. Visit the ASUS website (www.asus.com) to download the latest BIOS file. 4.1.5 ASUS Update utility The ASUS Update is a utility that allows you to manage, save, and update the motherboard BIOS in Windows® environment.
Updating the BIOS through the Internet To update the BIOS through the Internet: 4-8 1. Launch the ASUS Update utility from the Windows® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate e. The ASUS Update main window appears. 2. Select U p d a t e B I O S f r o m t h e I n t e r n e t option from the drop-down menu, then click N e x tt. 3. Select the ASUS FTP site nearest you to avoid network traffic, or click A u t o S e l e c tt. Click N e x tt.
4. From the FTP site, select the BIOS version that you wish to download. Click Next. 5. Follow the screen instructions to complete the update process. The ASUS Update utility is capable of updating itself through the Internet. Always update the utility to avail all its features. Updating the BIOS through a BIOS file To update the BIOS through a BIOS file: 1. 2.
4.2 BIOS setup program This motherboard supports a programmable firmware chip that you can update using the provided utility described in section “4.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you can change the configuration of your computer in the future.
4.2.1 BIOS menu screen Menu items Configuration fields Menu bar System Time System Date Legacy Diskette A [11:51:19] [Mon,06/14/2004] [1.44M, 3.5 in] Primary IDE Master Primary IDE Slave Third IDE Master Third IDE Slave Fourth IDE Master Fourth IDE Slave IDE Configuration : : : : : : [ST320413A] [Pioneer CD-ROM ATA] [Not Detected] [Not Detected] [Not Detected] [Not Detected] General help Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure the System time.
4.2.4 Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting M a i n shows the Main menu items. The other items (Advanced, Power, Boot, and Exit) on the menu bar have their respective menu items. 4.2.5 System Time System Date Legacy Diskette A Primary IDE Master Primary IDE Slave Third IDE Master Third IDE Slave Fourth IDE Master Fourth IDE Slave IDE Configuration [11:51:19] [Thu 06/10/2004] [1.44M, 3.
4.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information. Refer to section “4.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them. System Time System Date Legacy Diskette A Primary IDE Master Primary IDE Slave Third IDE Master Third IDE Slave Fourth IDE Master Fourth IDE Slave IDE Configuration [11:51:19] [Mon,06/14/2004] [1.44M, 3.
4.3.4 Primary, Third, and Fourth IDE Master/Slave While entering Setup, the BIOS automatically detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press to display the IDE device information. Primary IDE Master System Time System Date Vendor Size LBA Mode Block Mode PIO Mode Async DMA Ultra DMA SMART Monitoring : : : : : : : : : : [11:51:19] [Mon,06/14/2004] ST320413A 20.
PIO Mode [Auto] Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] Selects the DMA mode. Configuration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] SMART Monitoring [Auto] Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled] 32Bit Data Transfer [Disabled] Enables or disables 32-bit data transfer.
Enhanced Mode Support On [SATA mode] The default setting SATA allows you to use native OS on Serial ATA and Parallel ATA ports. We recommend that you do not change the default setting for better OS compatibility. In this setting, you may use legacy OS on the Parallel ATA ports o n l y i f you did not install any Serial ATA device. The S-ATA+P-ATA and P-ATA options are for advanced users only. If you set to any of these options and encounter problems, revert to the default setting S A T A A.
4.3.6 System Information This menu gives you an overview of the general system specifications. The BIOS automatically detects the items in this menu. AMIBIOS Version : 08.00.10 Build Date : 06/18/04 Processor Type Speed Count : Genuine Intel(R) CPU 3.
4.4 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Take caution when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. Adjust system frequency/voltage JumperFree Configuration LAN Cable Status USB Configuration CPU Configuration Chipset Onboard Devices Configuration PCI PnP 4.4.
The following items appear only when you set the A I O v e r c l o c k i n g item to [Manual]. CPU Frequency [XXX] Displays the frequency sent by the clock generator to the system bus and PCI bus. The value of this item is auto-detected by the BIOS. Use the < + > and < - > keys to adjust the CPU frequency. You can also type the desired CPU frequency using the numberic keypad. The values range from 100 to 400. Refer to the table below for the correct Front Side Bus and CPU External Frequency settings.
The following items also appear when the A I O v e r c l o c k i n g item is set to [AI NOS]. Memory Voltage [Auto] Allows you to select the DDR2 reference voltage. Configuration options: [1.80V] [1.90V] [2.00V] [2.10V] [Auto] Refer to the DDR2 documentation before adjusting the memory voltage. Setting a very high memory voltage may damage the memory module(s)! Chipset Core Voltage [Auto] Allows you to select the chipset core voltage. Configuration options: [1.50V] [1.
The following item appears only when the A I O v e r c l o c k i n g item is set to [Overclock Profile]. Overclock Options [Overclock 5%] Allows you to overclock the CPU speed through the available preset values.
4.4.2 LAN Cable Status The items in this menu display the status of the Local Area Network (LAN) cable. POST Check LAN cable LAN Cable Status Pair Status Length 1-2 3-6 4-5 7-8 0.0M 0.0M 0.0M 0.0M Open Open Open Open [Disabled] Check LAN cable during POST. POST Check LAN cable [Disabled] Enables or disables checking of the LAN cable during POST. Configuration options: [Disabled] [Enabled] 4.4.3 USB Configuration The items in this menu allow you to change the USB-related features.
Legacy USB Support [Auto] Allows you to enable or disable support for USB devices on legacy operating systems (OS). Setting to Auto allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled. Configuration options: [Disabled] [Enabled] [Auto] USB 2.0 Controller [Disabled] Allows you to enable or disable the USB 2.0 controller. Configuration options: [Enabled] [Disabled] USB 2.
VID CMOS Setting [ 62] Allows you to set the VID CMOS setting at which the processor is to run. The default value of this item is auto-detected by BIOS. Use the < + > or < - > keys to adjust the values. You can only adjust the R a t i o C M O S and the V I D C M O S setting if you installed an unlocked CPU. Refer to the CPU documentation for details. Microcode Updation [Enabled] Enables or disables microcode updation.
4.4.5 Chipset The Chipset menu allows you to change the advanced chipset settings. Select an item then press to display the sub-menu. Advanced Chipset Settings Configure DRAM Timing by SPD [Enabled] Graphic Adapter Priority Internal Graphics Mode Select Fixed Graphic Memory Size DVMT Graphic Memory Size [PCI Express/Int-VGA] [Enabled, 8 MB] [32 MB] [32 MB] PEG Buffer Length Link Latency PEG Root Control Slot Power [Auto] [Auto] [Auto] [Auto] Enable or disable DRAM timing.
Graphic Adapter Priority [PCI Express/Int-VGA] Allows selection of the graphics controller to use as primary boot device. Configuration options: [Internal VGA] [PCI Express/Int-VGA] [PCI Express/ PCI] [PCI/PCI Express] [PCI/Int-VGA] Internal Graphics Mode Select [Enabled, 8 MB] Allows selection of the amount of system memory pre-allocated by the internal graphics device.
4.4.6 Onboard Devices Configuration Configure Win627EHF Super IO Chipset Azalia Controller Front Panel Support Type Onboard 1394 Controller Onboard LAN LAN Option ROM ITE8212F Controller Detecting Device Time [Enabled] [AC97] [Enabled] [Enabled] [Disabled] [IDE Mode] [Quick Mode] Serial Port1 Address Parallel Port Address Parallel Port Mode ECP Mode DMA Channel Parallel Port IRQ Onboard Game/MIDI Port [3F8/IRQ4] [378] [ECP] [DMA3] [IRQ7] [Disabled] Enable or disable the Azalia controller.
Serial Port1 Address [3F8/IRQ4] Allows you to select the Serial Port1 base address. Configuration options: [Disabled] [3F8/IRQ4] [2F8/IRQ3] [3E8/IRQ4] [2E8/IRQ3] Parallel Port Address [378] Allows you to select the Parallel Port base addresses. Configuration options: [Disabled] [378] [278] [3BC] Parallel Port Mode [ECP] Allows you to select the Parallel Port mode.
4.4.7 PCI PnP The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices. Take caution when changing the settings of the PCI PnP menu items. Incorrect field values can cause the system to malfunction. Advanced PCI/PnP Settings WARNING: Setting wrong values in below sections may cause system to malfunction.
PCI IDE BusMaster [Enabled] Allows BIOS to use PCI bus mastering when reading/writing to IDE devices. Configuration options: [Disabled] [Enabled] IRQ-xx assigned to [PCI Device] When set to [PCI Device], the specific IRQ is free for use of PCI/PnP devices. When set to [Reserved], the IRQ is reserved for legacy ISA devices.
4.5 Power menu The Power menu items allow you to change the settings for the ACPI and Advanced Power Management (APM). Select an item then press to display the configuration options. Suspend Mode ACPI 2.0 Support ACPI APIC Support [Auto] [No] [Enabled] Select the ACPI state used for System Suspend. APM Configuration Hardware Monitor 4.5.1 Suspend Mode [Auto] Allows you to select the Advanced Configuration and Power Interface (ACPI) state to be used for system suspend.
4.5.4 APM Configuration APM Configuration Power Button Mode Go into On/Off or Suspend when Power button is pressed. [On/Off] Restore on AC Power Loss [Power Off] Power On By RTC Alarm [Disabled] Power On By External Modems [Disabled] Power On By PCI Devices [Disabled] Power On By PS/2 Keyboard [Disabled] Keyboard Wakeup Password : Not Installed Power On By PS/2 Mouse [Disabled] Power Button Mode [On/Off] Allows the system to go into On/Off mode or suspend mode when the power button is pressed.
Power On By PCI Devices [Disabled] When set to [Enabled], this parameter allows you to turn on the system through a PCI LAN or modem card. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Enabled] Power On By PS/2 Keyboard [Disabled] Allows you to use specific keys on the keyboard to turn on the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead.
4.5.5 Hardware Monitor Hardware Monitor CPU Temperature CPU Temperature MB Temperature [51ºC/122.5ºF] [41ºC/105.5ºF] CPU Fan Speed CPU Q-Fan Control Chassis Fan1 Speed Chassis Q-Fan Control Power Fan Speed [3813 RPM] [Disabled] [N/A] [Disabled] [N/A] VCORE Voltage 3.3V Voltage 5V Voltage 12V Voltage [ 1.320V] [ 3.345V] [ 5.094V] [11.880V] CPU Temperature [xxxºC/xxxºF] MB Temperature [xxxºC/xxxºF] The onboard hardware monitor automatically detects and displays the motherboard and CPU temperatures.
CPU Fan Ratio [Auto] Allows you to select the appropriate CPU fan speed ratio for the system. The default [Auto] automatically selects the fan speed ratio when operating a low CPU temperature. Select a higher ratio if you installed additional devices and the system requires more ventilation. This item appears only when the CPU Q-Fan Control item is Enabled.
4.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press to display the sub-menu. APM Configuration Specifies the Boot Device Boot Priority sequence. Boot Device Priority Boot Settings Configuration Security 4.6.1 Boot Device Priority Boot Device Priority 1st Boot Device 2nd Boot Device 3rd Boot Device [1st FLOPPY DRIVE] [PM-ST330620A] [PS-Pioneer CD-ROM] Specifies the boot sequence from the availabe devices.
4.6.2 Boot Settings Configuration Boot Settings Configuration Quick Boot Full Screen Logo AddOn ROM Display Mode Bootup Num-Lock PS/2 Mouse Support Wait For ‘F1’ If Error Hit ‘DEL’ Message Display Interrupt 19 Capture [Enabled] [Enabled] [Force BIOS] [On] [Auto] [Enabled] [Enabled] [Disabled] Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system.
Hit ‘DEL’ Message Display [Enabled] When set to Enabled, the system displays the message “Press DEL to run Setup” during POST. Configuration options: [Disabled] [Enabled] Interrupt 19 Capture [Disabled] When set to [Enabled], this function allows the option ROMs to trap Interrupt 19. Configuration options: [Disabled] [Enabled] 4.6.3 Security The Security menu items allow you to change the system security settings. Select an item then press to display the configuration options.
If you forget your BIOS password, you can clear clear it by erasing the CMOS Real Time Clock (RTC) RAM. See section “2.6 Jumpers” for information on how to erase the RTC RAM. After you have set a supervisor password, the other items appear to allow you to change other security settings.
The message “Password Installed” appears after you set your password successfully. To change the user password, follow the same steps as in setting a user password. Clear User Password Select this item to clear the user password. Password Check [Setup] When set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system.
Exit & Save Changes Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM. An onboard backup battery sustains the CMOS RAM so it stays on even when the PC is turned off. When you select this option, a confirmation window appears. Select Y e s to save changes and exit.
4-42 Chapter 4: BIOS setup
This chapter describes the contents of the support CD that comes with the motherboard package.
Chapter summary 5 5.1 Installing an operating system ............................................. 5-1 5.2 Support CD information ........................................................ 5-1 5.3 Software information ........................................................... 5-8 5.4 RAID configurations ............................................................ 5-16 5.5 Creating a RAID driver disk .................................................
5.1 Installing an operating system This motherboard supports Windows® 2000/2003 Server/XP operating systems (OS). Always install the latest OS version and corresponding updates to maximize the features of your hardware. 5.2 • Motherboard settings and hardware options vary. Use the setup procedures presented in this chapter for reference only. Refer to your OS documentation for detailed information.
5.2.2 Drivers menu The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. QFE Update Installs the Quick Fix Engineering (QFE) driver updates. Intel Chipset Inf Update Program This item installs the Intel® Chipset INF Update Program. This driver enables Plug-n-Play INF support for the Intel® chipset components on the motherboard.
Marvell Yukon Gigabit Ethernet Driver Installs the Marvell® Yukon 88E8053 PCI Express™ Gigabit LAN driver that provides up to 1000 Mbps data transfer rates. ITE8212 Driver and Application Installs the ITE® 8212 driver and application. Make ITE8212 Driver Disk Allows you to create a driver disk for the ITE® 8212 IDE RAID setup. USB 2.0 Driver Installs the USB 2.0 driver. The screen display and drivers option may not be the same for different operating system versions. 5.2.
ASUS PC Probe This smart utility monitors the fan speed, CPU temperature, and system voltages, and alerts you of any detected problems. This utility helps you keep your computer in healthy operating condition. ASUS Update The ASUS Update utility allows you to update the motherboard BIOS in a Windows® environment. This utility requires an Internet connection either through a network or an Internet Service Provider (ISP). See page 4-7 for details.
5.2.4 Manuals menu The Manuals menu contains a list of supplementary user manuals. Click an item to open the folder of the user manual. Install the Adobe® Acrobat® Reader from the Utilities menu before opening the manual files. C-Media Audio User’s Manual Allows you to open the C-Media CMI9880 audio user’s manual. Intel Application Accelerator RAID User’s Manual Allows you to open the Intel® Application Accelerator RAID User’s manual.
5.2.5 ASUS Contact information Click the C o n t a c t tab to display the ASUS contact information. You can also find this information on the inside front cover of this user guide. 5.2.6 Other information The icons on the top right corner of the screen give additional information on the motherboard and the contents of the support CD. Click an icon to display the specified information. Motherboard Info Displays the general specifications of the motherboard.
Browse this CD Displays the support CD contents in graphical format. Technical support Form Displays the ASUS Technical Support Request Form that you have to fill out when requesting technical support. Filelist Displays the contents of the support CD and a brief description of each in text format.
5.3 Software information Most of the applications in the support CD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software application for more information. 5.3.1 ASUS MyLogo™ The ASUS MyLogo™ utility lets you customize the boot logo. The boot logo is the image that appears on screen during the Power-On-Self-Tests (POST).
7. When the logo images appear on the right window pane, select an image to enlarge by clicking on it. 8. Adjust the boot image to your desired size by selecting a value on the R a t i o box. 9. When the screen returns to the ASUS Update utility, flash the original BIOS to load the new boot logo. 10. After flashing the BIOS, restart the computer to display the new boot logo during POST.
5.3.2 AI Net 2 The Marvell® Virtual Cable Tester™ (VCT) is a cable diagnostic utility that reports LAN cable faults and shorts using the Time Domain Reflectometry (TDR) technology. The VCT detects and reports open and shorted cables, impedance mismatches, pair swaps, pair polarity problems, and pair skew problems of up to 64 ns at one meter accuracy. The VCT feature reduces networking and support costs through a highly manageable and controlled network system.
5.3.3 C-Media 3D audio configuration The C-Media 3D Audio Configuration utility allows easy installation and set up of audio devices through a user-friendly interface. The utility is automatically installed when you install the C-Media CMI9880 audio driver and application from the motherboard support CD. Refer to section “5.2.2 Drivers menu.” Launching the C-Media 3D Audio Configuration utility Launch the C-Media 3D Audio Configuration utility by double clicking the C-Media icon on the Windows® taskbar.
Smart Jack Setting g. You can configure the function of the rear panel, front panel, and digital I/O audio ports from this section. Click the Smart Jack setting button that corresponds to the port that you want to configure. Mode Selection n. This section allows you to set the Speaker Tester or the Digital Signal Processing (DSP). Click the button to change the audio modes. Speaker Tester and Audio DSP Setting g. You can configure your speaker setup and the audio DSP settings in this section.
Effect The E f f e c t tab allows you to control the environment emulation, set the environment size, and adjust the equalizer settings. Environment settings Equalizer settings Environment size E n v i r o n m e n tt. This section contains various pre-programmed enviroment emulations. There are four featured materials that emulate the bathroom, concert hall, underwater, and music pub environments. Click the corresponding button to set an environment emulation.
Device Setting The D e v i c e S e t t i n g tab allows you to enable the audio CODEC multi-streaming feature, select a sound playback, and sound recording devices. Information The I n f o r m a t i o n tab displays your 3D audio engine, audio CODEC, audio driver, audio controller, and DirectX information.
Using Dolby® Digital Live Live™ The Dolby® Digital Live™ technology encodes your computer’s digital audio contents to real-time Dolby® Digital streams. Using the CODEC and the Sony/Philips Digital Interface (S/PDIF) ports on the motherboard, you can send the encoded Dolby® Digital streams to an AC-3 decoder for playback on a multi-channel speaker system. Refer to the following illustrations when converting sounds to Dolby® Digital streams.
5.4 RAID configurations The motherboard comes with the ITE® 8212F and the Intel® ICH6R Southbridge RAID controllers that allow you to configure IDE and Serial ATA hard disk drives as RAID sets. The motherboard supports the following RAID configurations. R A I D 0 (Data striping) optimizes two identical hard disk drives to read and write data in parallel, interleaved stacks.
5.4.1 Installing hard disks The motherboard supports Ultra DMA 133/100/66 and Serial ATA hard disk drives. For optimal performance, install identical drives of the same model and capacity when creating a disk array. Installing Parallel ATA hard disks To install IDE hard disks for a RAID configuration: 1. Set the jumpers of each hard disk as Master/Master or Slave/Slave. 2. Install the hard disks into the drive bays. 3. Connect the HDD signal cables. 4.
5.4.2 Intel® RAID configurations This motherboard supports RAID 0, RAID 1, and Intel® Matrix Storage configurations for Serial ATA hard disks drives through the Intel® ICH6R chipset. Use the Intel® Application Accelerator RAID Option ROM utility to configure a disk array. Setting the BIOS RAID items After installing the hard disk drives, make sure to set the necessary RAID items in the BIOS before setting your RAID configuration. To set the BIOS RAID items: 1. 3.
At the bottom of the screen are the navigation keys. These keys allow you to move through and select menu options. [ ]-Change [TAB]-Next [ESC] Previous Menu [Enter]-Select Creating a RAID Volume To create a RAID volume: 1. From the Intel Application Accelerator RAID Option ROM utility main menu, select 1 . C r e a t e R A I D V o l u m e then press . The following screen appears. Intel(R) Application Accelerator RAID Option ROM v4.0.0.6211 Copyright(C) 2003-04 Intel Corporation.
T I P : For server systems, use of a lower array block size is recommended. For multimedia computer systems used mainly for audio and video editing, a higher array block size is recommended for optimum performance. b. If you selected RAID (MIrrored), the Create Volume prompt appears. 4. On the Create Volume prompt, press to create the array. The utility prompts a confirmation message, press . WARNING: ALL DATA ON SELECTED DISK WILL BE LOST.
2. Press to delete the RAID volume. The following confirmation message appears. [ VOLUME DELETE VERIFICATION ] ALL DATA IN THE VOLUME WILL BE LOST!! Are you sure you want to delete volume "RAID_Volume0"? (Y/N) 3. Press to confirm or to return to the configuration Main Menu. Resetting RAID Disks Drives Take caution when resetting a RAID to non-RAID. Resetting all RAID data will remove any internal RAID structure from all RAID disks! 1. Select the option 3 .
5.4.3 ITE® 8212F RAID configurations The ITE® 8212F IDE RAID controller supports RAID 0, RAID 1, RAID 0+1 and JBOD configurations. Use the IT8212 BIOS Setup Utility or the ATA RAID Manager application to configure a disk array. Setting the BIOS RAID items After installing the hard disk drives, make sure to set the necessary RAID items in the BIOS before setting your RAID configuration. To set the BIOS RAID items: 1. 2. 3.
3. At the bottom of the screen are the navigation keys. These keys allow you to move through and select from the menu options. [1]..[5] Select 4. [ESC] Exit Press the number of your selection or to exit. Auto-configuring a RAID array This option allows you to select a supported RAID set for the utility to automatically configure. To auto-configure a RAID set: 1. From the IT8212 Setup Utility screen, press <1>. The following screen appears. IT8212 Setup Utility (C)Copyright 2002-2004 ITE, Inc.
Defining a RAID array This option allows you to define supported RAID arrays. To define a RAID array: 1. From the IT8212 Setup Utility screen, press <2>. The following screen appears. IT8212 Setup Utility (C)Copyright 2002-2004 ITE, Inc. [ Define RAID Menu ] Array No Array Mode Drive No Size(MB) Status Array 0 ---- ---- ----- ----- Array 1 ---- ---- ----- ----- Array 2 ---- ---- ----- ----- Array 3 ---- ---- ----- ----- ∗ : Capacity (GB) ↑] Up ↓] Down [↑ [↓ 2.
3. Use the up or down arrow keys to select editable fields. 4. Use the Space bar to change field values. 5. Press to save RAID array. 6. Press to exit. Deleting a RAID array This option allows you to delete an existing RAID array. To delete a RAID array: 1. From the IT8212 Setup Utility screen, press <3>. The following screen appears. IT8212 Setup Utility (C)Copyright 2002-2004 ITE, Inc.
Rebuilding a RAID array This option allows you to reconstruct an existing RAID array. This option applies only to RAID1 (Mirrored) or RAID 0+1(Striped+Mirrored) sets. To rebuild a RAID array: 1. From the IT8212 Setup Utility screen, press <4>. The following screen appears. IT8212 Setup Utility (C)Copyright 2002-2004 ITE, Inc.
3. Use the up or down arrow keys to select a drive, then press . Follow succeeding screen instructions. 4. Press to exit. Viewing your RAID configuration This option allows you to view your RAID configuration. You can also enable or disable the Auto-rebuild function in this section. To view your RAID configuration: 1. From the IT8212 Setup Utility screen, press <5>. The following screen appears. IT8212 Setup Utility (C)Copyright 2002-2004 ITE, Inc.
5.5 Creating a RAID driver disk A floppy disk with the RAID driver is required when installing Windows® 2000/XP operating system on a hard disk drive that is included in a RAID set. To create a RAID driver disk: 1. 2. Place the motherboard support CD in the optical drive. When the D r i v e r s menu appears, select the RAID driver disk you wish to create: • Click M a k e I T E 8 2 1 2 D r i v e r D i s k to create an ITE® 8212F RAID driver disk.
