Motherboard P5LD2-X/1333
E3519 Revised Edition V2 October 2007 Copyright © 2007 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Notices.......................................................................................................... vi Safety information...................................................................................... vii About this guide........................................................................................ viii P5LD2-X/1333 specifications summary...................................................... x Chapter 1: Product introduction 1.1 Welcome!...........................
Contents 2.7 Connectors.................................................................................. 2-23 2.7.1 2.7.2 Rear panel connectors................................................... 2-23 Internal connectors........................................................ 2-24 Chapter 3: Powering up 3.1 3.2 Starting up for the first time......................................................... 3-1 Powering off the computer........................................................... 3-2 3.2.1 3.2.
Contents 4.4.2 CPU Configuration......................................................... 4-20 4.4.4 Onboard Devices Configuration..................................... 4-23 4.4.3 4.5 4.4.5 4.5.1 Suspend Mode . ............................................................ 4-27 4.5.3 ACPI APIC Support . ..................................................... 4-27 4.5.4 4.5.5 ACPI 2.0 Support .......................................................... 4-27 APM Configuration..............................
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • • • • • • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This guide contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports.
Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Instructions that you MUST follow to complete a task. NOTE: Tips and additional information to help you complete a task.
P5LD2-X/1333 specifications summary CPU LGA775 socket for Intel® Prescott/Smithfield/Cedarmill/ Conroe/Conroe L/Presler processors Supports Intel® EIST/Hyper-Threading Technology Chipset Northbridge: Intel® MCH 945GC Southbridge: Intel® ICH7 Front Side Bus 1333(O.
P5LD2-X/1333 specifications summary Internal I/O connectors Azalia High Definition Analog Front Panel Audio connector Chassis Intrusion 1 x 4-pin internal speaker connector 1 x 24-pin EPS12V power connector 1 x 4-pin ATX 12V power connector 2 x USB connectors for 4 additional USB 2.
xii
This chapter describes the motherboard features and the new technologies it supports.
Chapter summary 1 1.1 Welcome!....................................................................................... 1-1 1.3 Special features............................................................................. 1-2 1.2 Package contents..........................................................................
1.1 Welcome! Thank you for buying an ASUS® P5LD2-X/1333 motherboard! The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your motherboard package for the following items.
1.3 Special features 1.3.1 Product highlights Latest processor technology The motherboard comes with a 775-pin surface mount Land Grid Array (LGA) socket designed for the Intel® Prescott, Intel® Smithfield, Intel® Cedarmill, Intel® Conroe, Intel® Conroe L or Intel® Presler processor in the 775-land package. The motherboard supports the processors with 1333 (O.C)/1066/800/533 MHz Front Side Bus (FSB).
DDR2 memory support The motherboard supports DDR2 memory that features data transfer rates of 667/533/400 MHz to meet the higher bandwidth requirements of the latest 3D graphics, multimedia, and Internet applications. The dual-channel DDR2 architecture doubles the bandwidth of your system memory to boost system performance, eliminating bottlenecks with peak bandwidths of up to10.6 GB/s. See page 2-13 for details.
Green ASUS The motherboard and its packaging comply with the European Union’s Restriction on the use of Hazardous Substances (RoHS). This is in line with the ASUS vision of creating environment-friendly and recyclable products and packaging to safeguard consumers’ health while minimizing the impact on the environment. 1.3.2 Innovative ASUS features ASUS CrashFree BIOS 2 This feature allows you to restore the original BIOS data from the support CD in case when the BIOS codes and data are corrupted.
ASUS MyLogo™ The new feature present in the motherboard allows you to personalize and add style to your system with customizable boot logos. See page 5-6 for details.
1- Chapter 1: Product introduction
This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
Chapter summary 2 2.1 Before you proceed...................................................................... 2-1 2.3 Central Processing Unit (CPU).................................................... 2-6 2.2 2.4 Motherboard overview.................................................................. 2-2 System memory.......................................................................... 2-13 2.5 Expansion slots........................................................................... 2-18 2.
2.1 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Use a grounded wrist strap or touch a safely grounded object or to a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity. • Hold components by the edges to avoid touching the ICs on them.
2.2 Motherboard overview Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components. 2.2.1 Placement direction When installing the motherboard, make sure that you place it into the chassis in the correct orientation.
2.2.3 Motherboard layout PARALLE PORT RTM876-660-LF Attansic L2 PCIEX1_1 30.5cm (12in) Intel 945GC AUDIO EATXPWR LAN_USB12 SPEAKER USB34 DDR2 DIMM_B1 (64 bit,240-pin module) DDR2 DIMM_A1 (64 bit,240-pin module) LGA775 SPDIF_O1 COM1 ATX12V CHA_FAN PS/2KBMS T: Mouse B: Ke yboard CPU_FAN 18.3cm (7.
2.2.4 Layout contents Slots Page 1. PCIe x16 2. PCIe x 1 3. PCI 2-20 2-20 2-20 Jumpers Page 1. Clear RTC RAM (3-pin CLRTC) 2. USB Device wake-up (3-pin PS2_USBPWR) Rear panel connectors Page 1. PS/2 mouse port (green) 2-23 3. LAN (RJ-45) port 2-23 2. 4. 5. 6. 7. 8. 9. 10. 11. 2- 2-21 2-22 Parallel port Line In port (light blue) Line Out port (green) Microphone port (pink) USB 2.0 ports 1 and 2 USB 2.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
2.3 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA775 socket designed for the Intel® Prescott/Smithfield/Cedarmill/ Conroe/Conroe L/Presler processor in the 775-land package • • • 2.3.1 Upon purchase of the motherboard, make sure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components.
2. Press the load lever with your thumb (A), then move it to the left (B) until it is released from the retention tab. Retention tab Load lever A PnP cap B This side of the socket box should face you. To prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU. 3. Lift the load lever in the direction of the arrow to a 135º angle. 4.
The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU! 6. Close the load plate (A), then push the load lever (B) until it snaps into the retention tab. A B The motherboard supports Intel® Prescott/Smithfield/Cedarmill/ Conroe/Conroe L/Presler LGA775 processors with the Intel® Enhanced Intel SpeedStep® Technology (EIST) and Hyper-Threading Technology.
2.3.2 Installing the CPU heatsink and fan The Intel® Prescott/Smithfield/Cedarmill/ Conroe/Conroe L/Presler LGA775 processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. • When you buy a boxed Intel® Prescott/Smithfield/Cedarmill/ Conroe/Conroe L/Presler processor, the package includes the CPU fan and heatsink assembly. If you buy a CPU separately, make sure that you use only Intel®‑certified multi‑directional heatsink and fan.
2. Push down two fasteners at a time in a diagonal sequence to secure the heatsink and fan assembly in place. B A A 3. A B B A B Connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN. CPU_FAN GND CPU FAN PWR CPU FAN IN CPU FAN PWM P5LD2-X/1333 P5LD2-X/1333.CPU.Fan.Connector Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector.
2.3.3 Uninstalling the CPU heatsink and fan To uninstall the CPU heatsink and fan: 1. 2. 3. 4. Disconnect the CPU fan cable from the connector on the motherboard. Rotate each fastener counterclockwise. Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and fan assembly from the motherboard. A B B A B A A B Carefully remove the heatsink and fan assembly from the motherboard.
5. Rotate each fastener clockwise to ensure correct orientation when reinstalling. Narrow end of the groove The narrow end of the groove should point outward after resetting. (The photo shows the groove shaded for emphasis.) Refer to the documentation in the boxed or stand-alone CPU fan package for detailed information on CPU fan installation.
2.4 System memory 2.4.1 Overview The motherboard comes with two Double Data Rate 2 (DDR2) Dual Inline Memory Modules (DIMM) sockets. 128 Pins 112 Pins DIMM_A1 DIMM_B1 The figure illustrates the location of the DDR2 DIMM sockets: P5LD2-X/1333 P5LD2-X/1333.240-pin.DDR2.DIMM.Sockets 2.4.2 Channel Sockets Channel A DIMM_A1 Channel B DIMM_B1 Memory configurations You may install 128 MB, 256 MB, 512 MB and 1 GB unbuffered non-ECC DDR2 DIMMs into the DIMM sockets.
Qualified Vendors Lists (QVL) DDR2-533 Size 2-14 Vendor Mode DIMM support CL Brand Side(s) Component A B • • HY5PS56821F-C4 • • N/A Kingston DS D6408TE7BL-37 • KVR533D2N4/1G N/A Kingston DS D6408TLRAGL37U Samsung M378T3253FG0-CD5 N/A Samsung SS K4T56083QF-GCD5 512MB Samsung M378T6553BG0-CD5 4 Samsung SS 256MB Qimonda HYS64T32000HU-3.7-A 4 Qimonda SS 512MB Qimonda HYS64T64000GU-3.7-A 4 Qimonda SS 512MB Qimonda HYS64T64000HU-3.
DDR2-667 Size Vendor DIMM support Mode 256MB Kingston KVR667D2N5/256 512MB Kingston KVR667D2N5/512 1G Kingston KVR667D2N5/1G 256MB Kingston 1G Kingston 512MB Samsung 512MB Samsung 512MB Samsung 1G Samsung 1G Samsung 256MB Qimonda 512MB Qimonda 512MB Qimonda KVR667D2N5/256 KVR667D2N5/1G KR M378T6553CZ0-CE6 KR M378T6453FZ0-CE6 M378T6553CZ3-CE6 M378T2953CZ3-CE6 KR M378T2953CZ0-CE6 HYS64T32000HU-3S-A HYS64T32000HU-3S-A HYS64T64000HU-3S-A 1G Qimonda HYS64T128
DDR2-667 Size Vendor 1G PQI 512MB AENEON 512MB AENEON 1G AENEON 512MB AENEON 1G AENEON 1G AENEON Mode DDR2-667U 1G CL Brand Side(s) Component N/A N/A AENEON SS AET760UD00-30DA98Z N/A AENEON DS AET660UD00-30DB97X AET660UD00-30DA98Z AET760UD00-30DA98Z AET760UD00-30DB97X 5 N/A AENEON DS 5 5 1G TAKEMS TMS1GB264C081-665QI 5 1G TAKEMS TMS51B264C081-665AP TMS1GB264C081-665AE TMS1GB264C081-665AP 512MB VERITECH GTP512HLTM45EG 1G VERITECH GTP01GHLTM55EG 5 5 5 512MB
2.4.3 Installing a DIMM Unplug the power supply before adding or removing DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components. 2 To install a DIMM: 1. Unlock a DIMM socket by pressing 2. Align a DIMM on the socket the retaining clips outward. such that the notch on the DIMM matches the break on 3. 3 DDR2 DIMM notch the socket.
2.5 Expansion slots In the future, you may need to install expansion cards. The following sub‑sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. 2.5.1 Installing an expansion card To install an expansion card: 1. 2. 3. 4. 5. 6.
2.5.
2.5.4 PCI slots The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The figure shows a LAN card installed on a PCI slot. 2.5.5 PCI Express x16 slot This motherboard supports PCI Express x16 graphic cards that comply with the PCI Express specifications. The following figure shows a graphics card installed on the PCI Express x16 slot. 2.5.
2.6 1. Jumpers Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the onboard battery. 3. Move the jumper cap from pins 1-2 (default) to pins 2-3.
2. USB device wake-up (3-pin PS2_USBPW) This jumper allows you to wake up the computer from S1 mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB device. Set this jumper to pins 2-3 (+5VSB) to wake up the computer from S3 and S4 modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode). PS2_USBPW P5LD2-X/1333 1 2 +5V (Default) 2 3 +5VSB P5LD2-X/1333.USB.Device.Wake.
2.7 Connectors 2.7.1 Rear panel connectors 1 2 3 4 5 6 10 11 1. 2. 3. 9 8 7 PS/2 mouse port (green). This port is for a PS/2 mouse. Parallel port. This 25-pin port connects a parallel printer, a scanner, or other devices. LAN (RJ-45) port. This port allows 10/100Mb connection to a Local Area Network (LAN) through a network hub. Refer to the table below for the LAN port LED indications.
Audio 2, 4, or 6-channel configuration Port 2-channel 4-channel 6-channel Light Blue Line In Line In Line In Lime Line Out Front Speaker Out Front Speaker Out Pink Mic In Mic In Mic In 7. 8. 9. USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0/1.1 devices. USB 2.0 ports 3 and 4. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0/1.1 devices. Coaxial S/PDIF Out port.
2. ICH7 Primary IDE connector (40-1 pin PRI_IDE) This connector is for an Ultra DMA 100/66/33 signal cable. The Ultra DMA 100/66/33 signal cable has three connectors: a blue connector for the primary IDE connector on the motherboard, a black connector for an Ultra DMA 100/66/33 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 100/66/33 IDE master device (hard disk drive).
Important notes on Serial ATA • • You must install Windows® 2000 Service Pack 4 or the Windows® XP Service Pack 1 before using Serial ATA hard disk drives. When using the connectors in Standard IDE mode, connect the primary (boot) hard disk drive to the SATA1 or SATA2 connector. Refer to the table below for the recommended SATA hard disk drive connections. Serial ATA hard disk drive connection Connector SATA1/SATA2 SATA3/SATA4 4.
5. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC’97 audio standard. AAFP NC AGND NC NC SENSE2_RETUR Legacy AC’97 compliant definition MIC2 MICPWR Line out_R NC Line out_L P5LD2-X/1333 PORT1L PORT1R PORT2R SEBSE_SEND PORT2L GND PRESENSE# SENSE1_RETUR HD-audio-compliant pin definition P5LD2-X/1333.Front.Panel.Audio.
7. CPU and chassis fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN) The fan connectors support cooling fans of 350 mA ~ 2000 mA (24 W max.) or a total of 1 A ~ 3.48 A (41.76 W max.) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components.
9. ATX power connectors (24-pin EATXPW, 4-pin ATX12V) These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. • Use of an ATX 12 V Specification 2.0 -compliant power supply unit (PSU) that provides a minimum power of 350 W is recommended for a fullyconfigured system.
11. System panel connector (10-1 pin F_PANEL) This connector supports several chassis-mounted functions. PLED+ PLEDPWR GND PLED PWRBTN P5LD2-X/1333 IDELED+ IDELEDGround Reset F_PANEL HD LED RESET P5LD2-X/1333.System.Panel.Connector • • • • 2-30 System power LED (2-pin PLED) This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode.
This chapter describes the power up sequence, the vocal POST messages, and ways of shutting down the system.
Chapter summary 3.1 3.2 3 Starting up for the first time......................................................... 3-1 Powering off the computer...........................................................
3.1 Starting up for the first time 1. After making all the connections, replace the system case cover. 3. Connect the power cord to the power connector at the back of the system chassis. 2. 4. 5. Be sure that all switches are off. Connect the power cord to a power outlet that is equipped with a surge protector. Turn on the devices in the following order: a. Monitor c. System power b. 6.
3.2 Powering off the computer 3.2.1 Using the OS shut down function If you are using Windows® 2000: 1. 2. Click the Start button then click Shut Down... Make sure that the Shut Down option button is selected, then click the OK button to shut down the computer. If you are using Windows® XP: 1. 2. Click the Start button then select Turn Off Computer. Click the Turn Off button to shut down the computer. If you are using Windows® Vista: 1. Click > . 2.
This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
Chapter summary 4 4.1 Managing and updating your BIOS............................................. 4-1 4.3 Main menu................................................................................... 4-14 4.5 Power menu................................................................................. 4-27 4.2 4.4 4.6 4.7 BIOS setup program................................................................... 4-11 Advanced menu..........................................................................
4.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. 2. 3. 4. ASUS AFUDOS (Updates the BIOS in DOS mode using a bootable floppy disk.) ASUS CrashFree BIOS 2 (Updates the BIOS using a bootable floppy disk or the motherboard support CD when the BIOS file fails or gets corrupted.) ASUS EZ Flash (Updates the BIOS using a floppy disk during POST.) ASUS Update (Updates the BIOS in Windows® environment.
Windows® 2000 environment To create a set of boot disks for Windows® 2000: a. Insert a formatted, high density 1.44 MB floppy disk into the drive. b. Insert the Windows® 2000 CD to the optical drive. c. Click Start, then select Run. d. In the Open field, type D:\bootdisk\makeboot a: assuming that D is your optical drive letter. e. Press , then follow screen instructions to continue. Windows® Vista environment a. Insert a formatted, high density 1.44 MB floppy disk to the floppy disk drive.
1. 2. Copy the AFUDOS utility (afudos.exe) from the motherboard support CD to the bootable floppy disk you created earlier. Boot the system in DOS mode, then at the prompt type: afudos /o[filename] where the [filename] is any user-assigned filename not more than eight alphanumeric characters for the main filename and three alphanumeric characters for the extension name. A:\>afudos /oOLDBIOS1.rom Main filename 3. Extension name Press . The utility copies the current BIOS file to the floppy disk.
4. The utility verifies the file and starts updating the BIOS. A:\>afudos /iP5LD2XOC.rom AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB)) Copyright (C) 2002 American Megatrends, Inc. All rights reserved. WARNING!! Do not turn off power during flash BIOS Reading file ....... done Reading flash ...... done Advance Check ...... Erasing flash ...... done Writing flash ...... 0x0008CC00 (9%) Do not shut down or reset the system while updating the BIOS to prevent system boot failure! 5.
4.1.3 ASUS CrashFree BIOS 2 utility The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can update a corrupted BIOS file using the motherboard support CD or the floppy disk that contains the updated BIOS file. • Prepare the motherboard support CD or the floppy disk containing the updated motherboard BIOS before using this utility.
Recovering the BIOS from the support CD To recover the BIOS from the support CD: 1. Remove any floppy disk from the floppy disk drive, then turn on the system. 3. The utility displays the following message and automatically checks the floppy disk for the original or updated BIOS file. 2. Insert the support CD to the optical drive. Bad BIOS checksum. Starting BIOS recovery... Checking for floppy...
4.1.4 ASUS EZ Flash utility The ASUS EZ Flash feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS‑based utility. The EZ Flash utility is built-in the BIOS chip so it is accessible by pressing + during the Power-On Self Tests (POST). To update the BIOS using EZ Flash: 1. 2. 3. Visit the ASUS website (www.asus.com) to download the latest BIOS file for the motherboard and rename the same to P5LD2X.ROM.
4.1.5 ASUS Update utility The ASUS Update is a utility that allows you to manage, save, and update the motherboard BIOS in Windows® environment. The ASUS Update utility allows you to: • Save the current BIOS file • Update the BIOS from an updated BIOS file • • • Download the latest BIOS file from the Internet Update the BIOS directly from the Internet, and View the BIOS version information. This utility is available in the support CD that comes with the motherboard package.
Updating the BIOS through the Internet To update the BIOS through the Internet: 1. Launch the ASUS Update utility from the Windows® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate. The ASUS Update main window appears. 2. Select Update BIOS from the Internet option from the drop‑down menu, then click Next. ASUS P5LD2-X/1333 3. Select the ASUS FTP site nearest you to avoid network traffic, or click Auto Select. Click Next.
4. 5. From the FTP site, select the BIOS version that you wish to download. Click Next. Follow the screen instructions to complete the update process. The ASUS Update utility is capable of updating itself through the Internet. Always update the utility to avail all its features. Updating the BIOS through a BIOS file To update the BIOS through a BIOS file: 1. 2. 3. 4. 4-10 Launch the ASUS Update utility from the Windows® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate.
4.2 BIOS setup program This motherboard supports a programmable Serial Peripheral Interface (SPI) chip that you can update using the provided utility described in section “4.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to“Run Setup.” This section explains how to configure your system using this utility.
4.2.1 Menu items BIOS menu screen Menu bar System Time System Date Legacy Diskette A Primary IDE Master Primary IDE Slave Third IDE Master Third IDE Slave Fourth IDE Master Fourth IDE Slave IDE Configuration : : : : : : [04:51:19] [Tue 01/01/2002] [1.44M, 3.5 in] Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. [Not [Not [Not [Not [Not [Not Use [+] or [-] to configure system time. System Information Sub-menu items 4.2.
4.2.4 Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting Main shows the Main menu items. The other items (Advanced, Power, Boot, and Exit) on the menu bar have their respective menu items. 4.2.5 Sub-menu items System Time System Date Legacy Diskette A Language Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Fourth IDE Master IDE Configuration [11:10:19] [Thu 03/27/2003] [1.44M, 3.
4.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information. Refer to section “4.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them. System Time System Date Legacy Diskette A Primary IDE Master Primary IDE Slave Third IDE Master Third IDE Slave Fourth IDE Master Fourth IDE Slave IDE Configuration : : : : : : [04:51:19] [Tue 01/01/2002] [1.44M, 3.
4.3.4 Primary, Third and Fourth IDE Master/Slave The BIOS automatically detects the connected IDE devices. There is a separate sub-menu for each IDE device. Select a device item, then press to display the IDE device information. Primary IDE Master Device : Hard Disk Vendor : ST320413A Size : 20.
PIO Mode [Auto] Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] Selects the DMA mode. Configuration options: [Auto] SMART Monitoring [Auto] Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled] 32Bit Data Transfer [Disabled] Enables or disables 32-bit data transfer. Configuration options: [Disabled] [Enabled] 4.3.
The P-ATA+S-ATA and P-ATA options are for advanced users only. If you set to any of these options and encountered problems, revert to the default setting S-ATA. Configuration options: [S-ATA+P-ATA] [S‑ATA] [P-ATA] The Onboard IDE Operate Mode and sub-menu items appear only when the Configure SATA As item is set to [Standard IDE]. IDE Detect Time Out [35] Selects the time out value for detecting ATA/ATAPI devices. Configuration options: [0] [5] [10] [15] [20] [25] [30] [35] 4.3.
4.4 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Take caution when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. USB Configuration Configure the USB support. CPU Configuration Chipset Onboard Devices Configuration PCIPnP 4.4.1 USB Configuration The items in this menu allows you to change the USB-related features.
USB Function [Enabled] Allows the BIOS to auto-detect the number of USB ports in your system. Setting this item to [Disable] disables the USB device detection function. Configuration options: [Disabled] [Enabled] Legacy USB Support [Auto] Allows you to enable or disable support for legacy USB devices. Setting to [Auto] allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled.
4.4.2 CPU Configuration The items in this menu show the CPU-related information that the BIOS automatically detects. Configure Advanced CPU settings Manufacturer: Intel Brand String: Intel(R) Celeron(R)D CPU 2.
4.4.3 Chipset The menu allows you to change the advanced chipset settings. Select an item then press to display the sub-menu.
DRAM # Activate to Precharge [15 Clocks] Configuration options: [4 Clocks] [5 Clocks] ~ [18 Clocks] DRAM Write Recovery Time [4 Clocks] Configuration options: [2 Clocks] [3 Clocks] [4 Clocks] [5 Clocks] [6 Clocks] Hyper Path 3 [Auto] Allows you to enable or disable the ASUS Hyper Path 3 feature. Configuration options: [Disabled] [Enabled] [Auto] DRAM Throttling Threshold [Auto] Enable DRAM Throttling Thermal Throttling will make your system more stable.
4.4.4 Onboard Devices Configuration Configure Win627DHG Super IO Chipset HD Audio Controller [Enabled] Front Panel Suppot Type [HD Audio] Onboard PCIEX 10/100Mb LAN [Enabled] LAN Option ROM [Disabled] Serial Port1 Address Parallel Port Address Parallel Port Mode ECP Mode DMA Channel Parallel Port IRQ Enable or disable High Definition Audio Controller. [3F8/IRQ4] [378] [ECP] [DMA3] [IRQ7] HD Audio Controller [Enabled] Allows you to enable or disable the high-definition audio CODEC.
Parallel Port Mode [ECP] Allows you to select the Parallel Port mode. Configuration options: [Normal] [Bi-directional] [EPP] [ECP] ECP Mode DMA Channel [DMA3] Appears only when the Parallel Port Mode is set to [ECP]. This item allows you to set the Parallel Port ECP DMA.
4.4.5 PCI PnP The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices. Take caution when changing the settings of the PCI PnP menu items. Incorrect field values can cause the system to malfunction. Advanced PCI/PnP Settings WARNING: Setting wrong values in below sections may cause system to malfunction.
IRQ-xx assigned to [PCI Device] When set to [PCI Device], the specific IRQ is free for use of PCI/PnP devices. When set to [Reserved], the IRQ is reserved for legacy ISA devices.
4.5 Power menu The Power menu items allow you to change the settings for the ACPI and Advanced Power Management (APM) features. Select an item then press to display the configuration options. Suspend Mode ACPI 2.0 Support ACPI APIC Support [Auto] [Disabled] [Enabled] Select the ACPI state used for System Suspend. APM Configuration Hardware Monitor 4.5.1 Suspend Mode [Auto] Allows you to select the Advanced Configuration and Power Interface (ACPI) state to be used for system suspend.
4.5.4 APM Configuration APM Configuration Power Button Mode [On/Off] Restore on AC Power Loss Power On By RTC Alarm Power On By External Modems Power On By PCI Devices Power On By PCIE Devices Power On By PS/2 Keyboard Power On By PS/2 Mouse [Power Off] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] Go into On/Off, or Suspend when Power button is pressed.
RTC Alarm Minute To set the alarm minute, highlight this item and press the <+> or <-> key to make the selection. Configuration options: [00] [1]... ~ [59] RTC Alarm Second To set the alarm second, highlight this item and press the <+> or <-> key to make the selection. Configuration options: [00] [1]...
4.5.5 Hardware Monitor CPU Temprerature Hardware Monitor CPU Temperature [79.5ºC/175ºF] CPU Fan Speed (RPM) CPU Q-Fan Control Chassis Fan Speed (RPM) [4470RPM] [Disabled] [N/A] VCORE Voltage 3.3V Voltage 5V Voltage 12V Voltage [ 1.368V] [ 3.248V] [ 5.145V] [11.932V] CPU Temperature [xx.xºC/xx.xºF] CPU Fan Speed (RPM) [xxxx RPM] or [Ignored] The onboard hardware monitor automatically detects and displays the CPU fan speed in rotations per minute (RPM).
4.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press to display the sub-menu. Specifies the Boot Device Priority Sequence. Boot Settings Boot Device Priority Boot Settings Configuration Security A virtual floppy disk drive (Floppy Drive B: )may appear when you set the CD-ROM drive as the first boot device. Enter F1 F10 ESC 4.6.
4.6.2 Boot Settings Configuration Boot Settings Configuration Quick Boot Full Screen Logo AddOn ROM Display Mode Bootup Num-Lock PS/2 Mouse Support Wait For ‘F1’ If Error Hit ‘DEL’ Message Display Interrupt 19 Capture [Enabled] [Enabled] [Force BIOS] [On] [Auto] [Enabled] [Enabled] [Disabled] Quick Boot [Enabled] Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system.
Interrupt 19 Capture [Disabled] When set to [Enabled], this function allows the option ROMs to trap Interrupt 19. Configuration options: [Disabled] [Enabled] 4.6.3 Security The Security menu items allow you to change the system security settings. Select an item then press to display the configuration options. Security Settings Supervisor Password User Password : Not Installed : Not Installed to change password. again to disabled password.
After you have set a supervisor password, the other items appear to allow you to change other security settings. Security Settings Supervisor Password User Password : Not Installed : Not Installed Change Supervisor Password User Access Level Change User Password Clear User Password Password Check to change password. again to disable password.
Clear User Password Select this item to clear the user password. Password Check [Setup] When set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system.
4.7 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items. Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Load Setup Defaults Exit system setup after saving the changes. F10 key can be used for this operation. Enter F1 F10 ESC Select Screen Select Item Go to Sub-screen General Help Save and Exit Exit Pressing does not immediately exit this menu.
Load Setup Defaults Allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press , a confirmation window appears. Select to load the default values. Select Exit & Save Changes or make other changes before saving the values to the non-volatile RAM.
4-38 Chapter 4: BIOS setup
This chapter describes the contents of the support CD that comes with the motherboard package.
Chapter summary 5 5.1 Installing an operating system.................................................... 5-1 5.3 ASUS MyLogo™............................................................................ 5-6 5.2 Support CD information...............................................................
5.1 Installing an operating system This motherboard supports Windows® 2000/2003 Server/XP/64-bit XP/Vista operating systems (OS). Always install the latest OS version and corresponding updates to maximize the features of your hardware. 5.2 • Motherboard settings and hardware options vary. Use the setup procedures presented in this chapter for reference only. Refer to your OS documentation for detailed information.
5.2.2 Drivers menu The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. ASUS InstALL - Drivers Installation Wizard Installs the ASUS InstALL - Drivers Installation Wizard. Intel Chipset Inf Update Program Installs the Intel Chipset Inf Update Program. Realtek Audio Driver Install the Realtek Audio Driver. Attansic L2 Fast Ethernet Installs the Attansic L2 Fast Ethernet.
5.2.3 Utilities menu The Utilities menu shows the applications and other software that the motherboard supports. ASUS InstALL - Installation Wizard for Utilities This wizard guides you in installing the utilities. ASUS PC Probe II This smart utility monitors the fan speed, CPU temperature, and system voltages, and alerts you of any detected problems. This utility helps you keep your computer in healthy operating condition.
5.2.4 ASUS Contact information Click the Contact tab to display the ASUS contact information. You can also find this information on the inside front cover of this user guide. 5.2.5 Other information The icons on the top right corner of the screen give additional information on the motherboard and the contents of the support CD. Click an icon to display the specified information. Motherboard Info Displays the general specifications of the motherboard.
Browse this CD Displays the support CD contents in graphical format. Technical support Form Displays the ASUS Technical Support Request Form that you have to fill out when requesting technical support.
Filelist Displays the contents of the support CD and a brief description of each in text format. 5.3 ASUS MyLogo™ The ASUS MyLogo™ utility lets you customize the boot logo. The boot logo is the image that appears on screen during the Power‑On Self-Tests (POST). The ASUS MyLogo™ is automatically installed when you install the ASUS Update utility from the support CD. See section “5.2.3 Utilities menu” for details.
To launch the ASUS MyLogo™: 1. 2. 3. 4. 5. 6. Launch the ASUS Update utility. Refer to section “4.1.5 ASUS Update utility” for details. Select Options from the drop down menu, then click Next. Check the option Launch MyLogo to replace system boot logo before flashing BIOS, then click Next. Select Update BIOS from a file from the drop down menu, then click Next. When prompted, locate the new BIOS file, then click Next. The ASUS MyLogo window appears.
9. When the screen returns to the ASUS Update utility, flash the original BIOS to load the new boot logo. 10. After flashing the BIOS, restart the computer to display the new boot logo during POST.
The Appendix describes the CPU features that the motherboard supports.
Chapter summary A.1 A.2 A Enhanced Intel SpeedStep® Technology (EIST).........................A-1 Intel® Hyper-Threading Technology............................................
A.1 A.1.1 Enhanced Intel SpeedStep® Technology (EIST) • The motherboard comes with a BIOS file that supports EIST. You can download the latest BIOS file from the ASUS website (www.asus.com/ support/download/) if you need to update the BIOS. See Chapter 4 for details. • Visit www.intel.com for more information on the EIST feature.
8. 9. On the Power schemes section, click , then select any option except Home/ Office Desktop or Always On. Click Apply, then click OK. 10. Close the Display Properties window. After you adjust the power scheme, the CPU internal frequency slightly decreases when the CPU loading is low. The screen displays and procedures may vary depending on the operating system. A.2 Intel® Hyper-Threading Technology • The motherboard supports Intel® Pentium® 4 LGA775 processors with Hyper-Threading Technology.
