V-Series P5V900 ASUS PC (Desktop Barebone) R R
E3071 First Edition December 2006 Copyright © 2006 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Table of contents Notices................................................................................................. vi Safety information...............................................................................vii About this guide..................................................................................viii System package contents..................................................................... x Chapter 1: System Introduction 1.1 Welcome!..........................................
Table of contents Chapter 3: 3.1 Installing an operating system............................................... 3-2 3.2 Powering up........................................................................... 3-2 3.3 Support CD information......................................................... 3-2 3.4 3.3.1 Running the support CD........................................... 3-3 3.3.2 Utilities menu........................................................... 3-4 3.3.3 Make disk.......................
Table of contents 5.3 5.4 5.5 5.6 5.2.4 Menu items............................................................ 5-13 5.2.5 Sub-menu items..................................................... 5-13 5.2.6 Configuration fields................................................ 5-13 5.2.7 Pop-up window....................................................... 5-14 5.2.8 General help........................................................... 5-14 Main menu..................................................
Notices vi
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. • If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
About this guide Audience This guide provides general information and installation instructions about the ASUS V-Series P5V900 barebone system. This guide is intended for experienced users and integrators with hardware knowledge of personal computers. How this guide is organized This guide contains the following parts: 1. Chapter 1: System introduction This chapter gives a general description of the ASUS V-Series P5V900.
Conventions used in this guide WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Instructions that you MUST follow to complete a task. NOTE: Tips and additional information to aid in completing a task. Where to find more information Refer to the following sources for additional information and for product and software updates. 1.
System package contents Check your V-Series P5V900 system package for the following items. If any of the items is damaged or missing, contact your retailer immediately. Item description 1. ASUS V-Series P5V900 barebone system with • ASUS motherboard • 300 W (peak) PFC power supply unit • ASUS chassis 2. Cable • AC power cable 3. Support CD 4.
This chapter gives a general description of the ASUS V-Series P5V900. The chapter lists the system features including introduction on the front and rear panel, and internal components.
1-
1. Two empty 5.25-inch bays. These bays are for IDE optical drives. 2. 3.5-inch drive bays. These slots are for 3.5-inch floppy or hard disk drives. 3. Power button. Press this button to turn the system on. 4. Reset button. Press this button to reboot the system without turning off the power. 5. HDD LED. This LED lights up when data is read from or written to the hard disk drive. 6. USB 2.0 ports. These Universal Serial Bus 2.0 (USB 2.0) ports are available for connecting USB 2.
1.3 Rear panel The system rear panel includes the power connector and several I/O ports that allow convenient connection of devices.
6. Parallel port. This 25-pin port connects a printer, scanner, or other devices. 7. VGA port. This port connects a VGA monitor. 8. USB 2.0 ports 1, 2, 3 and 4. These 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. 9. Microphone port (pink). This port connects a microphone. 10. Line Out port (lime). This port connects a headphone or a speaker. In 4-channel and 6-channel configuration, the function of this port becomes Front Speaker Out. 11.
1- Chapter 1: System introduction
1.4 Internal components The illustration below is the internal view of the system when you remove the top cover and the power supply unit. The installed components are labeled for your reference. Proceed to Chapter 2 for instructions on installing additional system components. 5 2 3 6 9 7 8 4 1 R 10 11 13 1. 2. 3. 4. 5. 6. 7. 12 Front panel cover 5.25-inch optical drive bays Hard disk drive bay Floppy disk drive bay Power supply unit CPU socket DIMM sockets ASUS V-Series P5V900 8. 9. 10.
1- Chapter 1: System introduction
Chapter 2 R R Basic installation This chapter provides step-by-step instructions on how to install components in the system.
2.1 Preparation Before you proceed, make sure that you have all the components you plan to install in the system.
2-
2.
3. 4. Lift the load lever in the direction of the arrow to a 135º angle. PnP cap Load plate Lift the load plate with your thumb and forefinger to a 100º angle (4A), then push the PnP cap from the load plate window to remove (4B). 4B 4A 3 5. Position the CPU over the socket, making sure that the gold triangle is on the bottom‑left corner of the socket then fit the socket alignment key into the CPU notch.
6. Apply Thermal Interface Material on the CPU before closing the load plate. DO NOT eat the Thermal Interface Material. If it gets into your eyes or touches your skin, make sure to wash it off immediately, and seek professional medical help. 7. Close the load plate (A), then push the load lever (B) until it snaps into the retention tab. A B 2.4.
If you purchased a separate CPU heatsink and fan assembly, make sure that the Thermal Interface Material is properly applied to the CPU heatsink or CPU before you install the heatsink and fan assembly. To install the CPU heatsink and fan: 1. 2. Place the heatsink on top of the installed CPU, making sure that the four fasteners match the holes on the motherboard. A B B A Push down two fasteners at a time in a diagonal sequence to secure the heatsink and fan assembly in place. A B B A 1 1 3.
2.5 Installing a DIMM The system motherboard comes with two Double Data Rate 2 (DDR2) Dual Inline Memory Module (DIMM) sockets. The following figure illustrates the location of the sockets: 2- • Install only identical (the same type and size) DDR2 memory modules. • Install only ASUS-certified memory modules. Refer to the DDR2 Qualified Vendors List on the next page for details. • Always install DIMMs with the same CAS latency.
Qualified Vendors Lists (QVL) ASUS V-Series P5V900 2-
Size 2-10 Vendor Model Side(s) Component A B Chapter 2: Basic installation
2.5.2 Installing a DDR2 DIMM Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components. 2 1. Unlock a DDR2 DIMM socket by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. DDR2 DIMM notch 1 1 Unlocked retaining clip A DDR2 DIMM is keyed with a notch so that it fits in only one direction.
2.6 Expansion slots In the future, you may need to install expansion cards. The following sub‑sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. 2.6.1 Installing an expansion card To install an expansion card: 1.
Standard interrupt assignments IRQ Standard Function 0 1 2 4 5 6 7 8 9 10 11 12 13 14 15 System Timer Keyboard Controller Re-direct to IRQ#9 Communications Port (COM1)* IRQ holder for PCI steering* Floppy Disk Controller Printer Port (LPT1)* System CMOS/Real Time Clock IRQ holder for PCI steering* IRQ holder for PCI steering* IRQ holder for PCI steering* PS/2 Compatible Mouse Port* Numeric Data Processor Primary IDE Channel Secondary IDE Channel * These IRQs are usually available for ISA or PCI devices.
2-14
2.7 Installing an optical drive Refer to the instructions in this section if you wish to install a new optical drive. Follow these steps to install an optical drive: 1. Place the chassis upright. 2. Remove the drive slot metal plate cover. 3. Insert the optical drive into the upper 5.25-inch drive bay and carefully push the optical drive into the bay until its screw holes align with the holes on the bay as shown. 4. Secure the optical drive with two screws on both sides of the bay. 3 4 4 5.
2-16 7. Connect the other end of the IDE ribbon cable to the secondary IDE connector (labeled SEC_IDE) on the motherboard. See page 4-7 for the location of this connector. 8. Remove the dummy drive slot cover from the front panel. 9. Replace the front panel.
2.8 Installing a hard disk drive The system may have one pre-installed 3.5-inch Serial ATA or IDE hard disk drive. Refer to this section to install additional Serial ATA or IDE hard disk drive(s). To install a Serial ATA hard disk drive: 1. Place the chassis upright. 2. Use a screw driver to remove the HDD drive slot metal plate cover. 3. With the HDD label side up, carefully insert the drive into the 3.
Serial ATA power cable Serial ATA cable 5. Connect one end of the Serial ATA cable to the SATA connector at the back of the drive, then connect the other end to a Serial ATA connector on the motherboard. See page 4-6 for the location of the Serial ATA connectors. 6. Connect a 15-pin Serial ATA power plug from the power supply unit to the 15-pin power connector at the back of the drive.
To install an IDE hard disk drive: 1. Follow steps 1-4 of the previous section. 2. Connect the blue interface of the IDE ribbon cable to the primary IDE connector (blue connector labeled PRI_IDE) on the motherboard. See page 4-7 for the location of the connector. IDE ribbon cable Power cable • If you will install only one hard disk drive, make sure to configure your hard disk drive as Master device before connecting the IDE cable and power plug.
2.9 Installing a floppy disk drive The V-Series P5V900 system comes with one 3.25-inch drive bay for a floppy disk drive. To install a floppy disk drive: 1. Remove the front panel cover. 2. Carefully insert the floppy disk drive into the floppy drive bay until the screw holes align with the holes on the bay. 3. Secure the floppy disk drive with two screws on both sides. 3 3 4. 2 Connect the floppy disk drive signal cable to the signal connector at the back of the drive.
2.10 Re-connecting cables You may have disconnected some cables when you were installing components. You must re-connect these cables before you replace the chassis cover. LED cables Reset button I HDD LED Power Switch Power LED Connect the reset button, power switch, power LED, and HDD LED cables to their respective leads in the system panel connector on the motherboard.
2-22
Chapter 3 R R Starting up This chapter helps you power up the system and install drivers and utilities from the support CD.
3.1 Installing an operating system The barebone system supports Windows® 2000/XP operating systems (OS). Always install the latest OS version and corresponding updates so you can maximize the features of your hardware. Because motherboard settings and hardware options vary, use the setup procedures presented in this chapter for general reference only. Refer to your OS documentation for more information. 3.2 • Windows XP OS setup cannot recognize Serial ATA hard drives without the necessary drivers.
3-
3.3.2 Utilities menu The Utilities menu shows the applications and other software that the motherboard supports. ASUS InstAll-Installation Wizard for Utilities Installs the ASUS InstAll-Installation Wizard Utilities.
3.3.3 Make Disk Make VIA VT8237 RAID Driver Disk Make the VIA VT8237 RAID Driver Disk. 3.3.4 Manual Intel LGA775 CPU install User’s Manual Install the Intel LGA775 CPU install user manual. VIA VT8237 RAID User’s Manual Install the VIA VT8237 RAID user manual.
3.3.5 ASUS Contact information Click the Contact tab to display the ASUS contact information. You can also find this information on the inside front cover of this user guide.
3.4 Software information Most of the applications in the support CD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software for more information. ASUS PC Probe II PC Probe II is a utility that monitors the computer’s vital components and alerts you of any problem with these components. PC Probe II senses fan rotations, CPU temperature, and system voltages, among others.
Button Function Opens the Configuration window Opens the Report window Opens the Desktop Management Interface window Opens the Peripheral Component Interconnect window Opens the Windows Management Instrumentation window Opens the hard disk drive, memory, CPU usage window Shows/Hides the Preference section Minimizes the application Closes the application Sensor alert When a system sensor detects a problem, the main window right handle turns red, as the illustrations below show.
Hardware monitor panels The hardware monitor panels display the current value of a system sensor such as fan rotation, CPU temperature, and voltages. The hardware monitor panels come in two display modes: hexagonal (large) and rectangular (small). When you check the Enable Monitoring Panel option from the Preference section, the monitor panels appear on your computer’s desktop.
Monitoring sensor alert The monitor panel turns red when a component value exceeds or is lower than the threshold value. Refer to the illustrations below. Small display Large display WMI browser Click to display the WMI (Windows Management Instrumentation) browser. This browser displays various Windows® management information. Click an item from the left panel to display on the right panel. Click the plus sign (+) before WMI Information to display the available information.
PCI browser Click to display the PCI (Peripheral Component Interconnect) browser. This browser provides information on the PCI devices installed on your system. Click the plus sign (+) before the PCI Information item to display available information. Usage The Usage browser displays real-time information on the CPU, hard disk drive space, and memory usage. Click to display the Usage browser. CPU usage The CPU tab displays real-time CPU usage in line graph representation.
Memory usage The Memory tab shows both used and available physical memory. The pie chart at the bottom of the window represents the used (blue) and the available physical memory. Configuring PC Probe II Click to view and adjust the sensor threshold values. The Config window has two tabs: Sensor/Threshold and Preference. The Sensor/Threshold tab enables you to activate the sensors or to adjust the sensor threshold values.
This chapter gives information about he motherboard that comes with the system. This chapter includes the motherboard layout, jumper settings, and connector locations.
4.1 Introduction The V-Series P5V900 barebone system comes with an ASUS motherboard. This chapter provides technical information about the motherboard for future upgrades or system reconfiguration. 4.2 Motherboard layout 21.8cm (8.6in) 24.5cm (9.
4-
2. USB device wake-up (3-pin USBPW12, USBPW34, USBPW56, USBPW78) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode). The USBPWR12 and USBPWR34 jumpers are for the rear USB ports.
3. Keyboard power (3-pin KBPWR) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) if you wish to wake up the computer when you press a key on the keyboard (the default is the Space Bar). This feature requires an ATX power supply that can supply at least 1A on the +5VSB lead, and a corresponding setting in the BIOS. KBPWR 1 2 +5V (Default) 2 3 +5VSB R Keyboard Power Setting 4. XSW (3-pin XSW1,2,3,4) .
4.4 1. Connectors Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. Pin 5 on the connector is removed to prevent incorrect cable connection when using a FDD cable with a covered Pin 5. FLOPPY PIN 1 R Floppy Disk Drive Connector 2. NOTE: Orient the red markings on the floppy ribbon cable to PIN 1.
3 IDE connectors (40-1 pin PRI_IDE, SEC_IDE) NOTE: Orient the red markings (usually zigzag) on the ID ribbon cable to PIN 1. IDE Connectors SEC_IDE R PIN1 PRI_IDE The onboard IDE connectors are for Ultra DMA 133/100/66 signal cable(s). There are three connectors on each Ultra DMA 133/100/66 signal cable: blue, black, and gray. Connect the blue connector to the motherboard’s IDE connector, then select one of the following modes to configure your device(s).
Never connect a 1394 cable to the USB connectors.
6. ATX power connectors (24-pin EATXPWR, 4-pin ATX12V) These connectors are for ATX power supply plugs. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. ATX12V GND +12V DC GND +12V DC R ATX Power Connector 7.
8. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC’97 audio standard.
4-11
4-12 Chapter 4: Motherboard info
Chapter 5 R R BIOS setup This chapter tells how to change system settings through the BIOS Setup menus and describes the BIOS parameters.
5.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. ASUS Update (Updates the BIOS in Windows® environment) 2. ASUS EZ Flash (Updates the BIOS during the Power-On Self Test) 3. Award BIOS Flash Utility (Updates the BIOS in DOS mode) 4. ASUS CrashFree BIOS 2 (Updates the BIOS when the BIOS file fails or gets corrupted.) Refer to the corresponding sections for details on these utilities.
Updating the BIOS through the Internet To update the BIOS through the Internet: 1. Launch the ASUS Update utility from the Windows® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate. The ASUS Update main window appears. 2. Select Update BIOS from the Internet option from the drop‑down menu, then click ASUS V-Series P5V900 3. Select the ASUS FTP site nearest you to avoid network traffic, or click Auto Select. Click Next.
4. From the FTP site, select the BIOS version that you wish to download. Click Next. 5. Follow the screen instructions to complete the update process. The ASUS Update utility is capable of updating itself through the Internet. Always update the utility to avail all its features. Updating the BIOS through a BIOS file To update the BIOS through a BIOS file: 5- 1. Launch the ASUS Update utility from the Windows® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate.
5.1.2 1. Creating a bootable floppy disk Do either one of the following to create a bootable floppy disk. DOS environment a. Insert a 1.44MB floppy disk into the drive. b. At the DOS prompt, type format A:/S then press . Windows® XP environment a. Insert a 1.44 MB floppy disk to the floppy disk drive. b. Click Start from the Windows® desktop, then select My Computer. c. Select the 3 1/2 Floppy Drive icon. d. Click File from the menu, then select Format. A Format 3 1/2 Floppy Disk window appears. e.
5.1.3 ASUS EZ Flash 2 utility The ASUS EZ Flash 2 feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS‑based utility. The EZ Flash 2 utility is built-in the BIOS chip so it is accessible by pressing + during the Power-On Self-Test (POST). To update the BIOS using EZ Flash 2: 1. Visit the ASUS website (www.asus.com) to download the latest BIOS file for the motherboard. 2.
5.1.4 AwardBIOS Flash Utility The Basic Input/Output System (BIOS) can be updated using the AwardBIOS Flash Utility. Follow these instructions to update the BIOS using this utility. 1. Download the latest BIOS file from the ASUS web site. Rename the file to V-P5V900.BIN and save it to a floppy disk. Save only the updated BIOS file in the floppy disk to avoid loading the wrong BIOS file. 2. Copy the AwardBIOS Flash Utility (awdflash.
7. Press when the utility prompts you to save the current BIOS file. The following screen appears. 8. The utility verifies the BIOS file in the floppy disk and starts flashing the BIOS file. AwardBIOS Flash Utility for ASUS V1.17 (C) Phoenix Technologies Ltd. All Rights Reserved For P4M900-8237A-P5VD2-VM DATE:11/12/2006 Flash Type - Winbond W39V040C/FC (4MB) File Name to Program: V-P5V900.
5.1.5 Saving the current BIOS file You can use the AwardBIOS Flash Utility to save the current BIOS file. You can load the current BIOS file when the BIOS file gets corrupted during the flashing process. To save the current BIOS file using the AwardBIOS Flash Utility: 1. Follow steps 1 to 6 of the previous section. 2. Press when the utility prompts you to save the current BIOS file. The following screen appears. AwardBIOS Flash Utility for ASUS V1.17 (C) Phoenix Technologies Ltd.
5-10
5.2 BIOS setup program This motherboard supports a programmable Low-Pin Count (LPC) chip that you can update using the provided utility described in section “4.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to“Run Setup.” This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you can change the configuration of your computer in the future.
5.2.1 BIOS menu screen Menu items Main Menu bar Advanced Power Configuration fields Phoenix-Award BIOS CMOS Setup Utility Boot Exit System Time System Date 15 : 30 : 36 Tue, Mar 28 2006 Legacy Diskette A: [1.44M, 3.5 in.
ASUS V-Series P5V900 5-13
5.2.7 Pop-up window Select a menu item then press to display a pop-up window with the configuration options for that item. Main Advanced Phoenix-Award BIOS CMOS Setup Utility Boot Exit System Time System Date 15 : 30 : 36 Thu, Apr 6 2006 Legacy Diskette A: [1.44M, 3.5 in.
5.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information. Refer to section “4.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them.
5.3.3 Primary IDE Master/Slave While entering Setup, the BIOS automatically detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press to display the IDE device information.
Access Mode [Auto] The default [Auto] allows automatic detection of an IDE hard disk drive. Select [CHS] for this item if you set the IDE Primary Master/Slave to [Manual]. Configuration options: [CHS] [LBA] [Large] [Auto] Before attempting to configure a hard disk drive, make sure you have the correct configuration information supplied by the drive manufacturer. Incorrect settings may cause the system to fail to recognize the installed hard disk. Capacity Displays the auto-detected hard disk capacity.
5.3.4 SATA 1/ 2 While entering Setup, the BIOS automatically detects the presence of Serial ATA devices. There is a separate sub-menu for each SATA device. Select a device item then press to display the SATA device information.
Head Shows the number of the hard disk read/write heads. This item is not configurable. Landing Zone Shows the number of landing zone per track. This item is not configurable. Sector Shows the number of sectors per track. This item is not configurable. After entering the IDE hard disk drive information into BIOS, use a disk utility, such as FDISK, to partition and format new IDE hard disk drives. This is necessary so that you can write or read data from the hard disk.
5.4.1 CPU Configuration Advanced Phoenix-Award BIOS CMOS Setup Utility CPU Configuration CPU Type Intel Genuine Processor CPU Speed 3.80GHz Cache RAM 2048K Current FSB Frequency 200MHz Delay Prior to Thermal [4 Min] Thermal Management [TM 1] TM2 Bus Ratio 14 X TM2 Bus VID 0.8375V Limit CPUID MaxVal [Disabled] Enhanced C1 (C1E) [Enabled] Excute Disable Bit [Enabled] Enhanced Intel SpeedStep(tm) Tech.
5.4.2 Chipset Advanced Phoenix-Award BIOS CMOS Setup Utility Chipset Primary Display Adapter VGA Share Memory Size F1:Help ESC: Exit Select Menu [PCI-E] [64M] ↑↓ : Select Item →←: Select Menu Item Specific Help -/+: Change Value Enter: Select Sub-menu F5: Setup Defaults F10: Save and Exit Primary Display Adapter [PCI-E] Select which graphics controller to use as the primary boot device. Configuration options: [PCI] [PCI-E] VGA Share Memory Size [64M] Sets the VGA Share Memory Size.
5.4.3 PCIPnP Advanced Phoenix-Award BIOS CMOS Setup Utility PCIPnP Select Menu Plug & Play O/S [No] Resources Controlled By x IRQ Resources Assign IRQ For VGA [Auto] [Enabled] ** PCI Express relative items ** Maximum Payload Size [4096] Item Specific Help Plug & Play O/S [No] When set to [No], the BIOS configures all the devices in the system. When set to [Yes] and if you install a Plug and Play operating system, the operating system configures the Plug and Play devices not required for boot.
SATA Controller [Enabled] Enable/Disable Onchip SATA. Configuration options: [Disabled] [Enabled] SATA Controller Mode [IDE] Select SATA mode. Configuration options: [IDE] [RAID] HDA Controller [Auto] Enable/Disable High Definition Audio controller.
Parallel Port Address [378/IRQ7] Select parallel port address. Configuration options: [Disabled] [378/IRQ7] [278/IRQ5] [3BC/IRQ7] Parallel Port Mode [Bi-Directional] Select parallel port mode. Configuration options: [Normal] [EPP] [ECP] [BiDirectional] ECP Mode Use DMA [3] Select ECP Mode use DMA. Configuration options: [1] [3] 5.4.5 USB Configuration The items in this menu allows you to change the USB-related features. Select an item then press to display the configuration options.
5.5 Power menu The Power menu items allow you to change the settings for the Advanced Configuration and Power Interface (ACPI) and the Advanced Power Management (APM). Select an item then press to display the configuration options. Main Advanced Power Phoenix-Award BIOS CMOS Setup Utility Boot Tools Exit ACPI Suspend Type ACPI APIC support APM Configuration Hardware Monitor F1:Help ESC: Exit 5.5.
5.5.
Restore on AC Power Loss [Power Off] Allows you to select to/not to restart the system after AC power loss. Configuration options: [Power Off] [Power On] [Last State] PWR Button < 4 secs [Instant-Off] When sets to [Instant-Off], the system will go to Soft-off instantly when power-button pressed for less than 4 seconds. When sets to [Suspend], the system will go to Suspend when power button is pressed.
5.5.4 Hardware Monitor The items in this sub-menu displays the hardware monitor values automatically detected by the BIOS. Select an item then press to display the configuration options. Power Phoenix-Award BIOS CMOS Setup Utility Hardware Monitor x Q-Fan Controller Vcore Voltage 3.3V Voltage 5V Voltage 12V Voltage [Enabled] [1.29V] [3.33V] [4.96V] [11.
CPU Fan Speed warning [ 800 RPM] Allows you to disable or set the CPU fan warning speed.
5.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press to display the sub-menu. Main Advanced Power Phoenix-Award BIOS CMOS Setup Utility Boot Tools Exit Select Menu Boot Device Priority Boot Settings Configuration Security Item Specific Help Select Boot Device Priority ↑↓ : Select Item →←: Select Menu F1:Help ESC: Exit 5.6.
5.6.
OS Select for DRAM > 64MB [Non-OS2] Set this item to OS2 only when you are running on an OS/2 operating system with an installed RAM of greater than 64 KB. Configuration options: [Non-OS2] [OS2] Full Screen LOGO [Enabled] Allows you to enable or disable the full screen logo display feature. Configuration options: [Disabled] [Enabled] Halt On [All, But Keyboard] Allows you to error report type. Configuration options: [All Errors] [No Errors] [All, But Keyboard] [All, But Diskette] [All, But Disk/Key] 5.6.
5-33
Pressing does not immediately exit this menu. Select one of the options from this menu or from the legend bar to exit. Exit & Save Changes Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM. An onboard backup battery sustains the CMOS RAM so it stays on even when the PC is turned off. When you select this option, a confirmation window appears. Select YES to save changes and exit.
