Motherboard P5VD2-MX/ P5V-VM DH
E2505 First Edition V1 May 2006 Copyright © 2006 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Notices ................................................................................................ vi Safety information ............................................................................. vii About this guide ............................................................................... viii P5VD2-MX/P5V-VM DH specifications summary ................................. x Chapter 1: Product introduction 1.1 Welcome! ...................................................................
Contents 1.10 Connectors ......................................................................... 1-26 1.10.1 Rear panel connectors .......................................... 1-26 1.10.2 Internal connectors ............................................... 1-28 Chapter 2: BIOS setup 2.1 2.2 2.3 iv Managing and updating your BIOS ........................................ 2-2 2.1.1 ASUS Update utility ................................................ 2-2 2.1.2 Creating a bootable floppy disk ..........
Contents 2.4 2.5 2.6 2.7 Advanced menu .................................................................. 2-20 2.4.1 CPU Configuration ................................................. 2-20 2.4.2 Chipset ................................................................. 2-21 2.4.3 PCIPnP ................................................................... 2-23 2.4.4 Onboard Devices Configuration ............................ 2-24 2.4.5 USB Configuration ............................................
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This manual contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports. This chapter also lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. D A N G E R / W A R N I N G : Information to prevent injury to yourself when trying to complete a task. C A U T I O N : Information to prevent damage to the components when trying to complete a task. I M P O R T A N T : Instructions that you MUST follow to complete a task. N O T E : Tips and additional information to help you complete a task.
P5VD2-MX/P5V-VM DH specifications summary CPU LGA775 socket for Intel® Core™2 Duo/Pentium® D/ Pentium® 4/Celeron® CPU support Intel® Presler 65nm Dual core CPU support Intel® next generation Core™2 Duo CPU support Compatible with Intel® 05B/05A and 04B/04A processors Supports Intel EIST/EM64T/Hyper-Threading Technology Chipset Northbridge: VIA P4M890 Southbridge: VIA VT8237A Front Side Bus 1066/800/533 MHz Memory 2 x 240-pin DIMM sockets support up to 4 GB of DDR2 533/400 unbufferred non-ECC memory
P5VD2-MX/P5V-VM DH specifications summary Overclocking Features ASUS C.P.R. (CPU Parameter Recall) SFS (Stepless Frequency Selection) from 133MHz up to 300MHz at 1MHz increment Adjustable FSB/DDR ratio. Fixed PCI-E/SATA frequencies. Rear panel 1 x Parallel port 1 x External SATA 1 x LAN (RJ-45) port 4 x USB 2.0/1.1 ports 1 x VGA port 1 x PS/2 keyboard port 1 x PS/2 mouse port 6-Channel Audio I/O ports BIOS features 4 Mb Flash ROM, Award BIOS, PnP, WfM2.0, ACPI2.0a, SM BIOS 2.
Extra specifications on P5V-VM DH ASUS Digital Home Features ASUS WiFi-AP Solo - 54 Mbps IEEE 802.11g and backwards compatible with 11 Mbps IEEE 802.11b - Access point mode - Station mode: Infrastructure mode or Ad-Hoc mode ASUS DH Remote™ - Power - Quick Power - Noise Off - EZ WiFi - Full Screen - AP Launch - Media Controller Zone ASUS MP3-In™ ASUS Digital Home Accessories ASUS DH Remote ASUS DH Remote Receiver ASUS WiFi-AP Solo omni-directional antenna ASUS MP3-In Module Wirelss LAN 54Mbps IEEE 802.
This chapter describes the motherboard features and the new technologies it supports.
1.1 Welcome! T h a n k y o u f o r b u y i n g a n A S U S® P 5 V D 2 - M X / P 5 V - V M D H motherboard! The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your motherboard package for the following items.
Intel® 65nm Dual-Core CPU support This motherboard supports Intel® Pentium® D/Pentium® 4/Celeron® dual-core processors built on the 65-nanometer (nm) process technology with copper interconnect. Dual-core processors contain two physical CPU cores with dedicated L2 caches to meet demands for more powerful processing. Intel®’s 65nm process is the most advanced chip manufacturing technology, delivering breakthrough performance, enhanced media experience, and low power consumption.
USB 2.0 technology The motherboard implements the Universal Serial Bus (USB) 2.0 specification, dramatically increasing the connection speed from the 12 Mbps bandwidth on USB 1.1 to a fast 480 Mbps on USB 2.0. USB 2.0 is backward compatible with USB 1.1. See pages 1-25 and 1-33 for details. S/PDIF digital sound ready The motherboard supports the S/PDIF Out function through the S/PDIF interface at midboard.
ASUS EZ Flash BIOS With the ASUS EZ Flash, you can easily update the system BIOS even before loading the operating system. No need to use a DOS-based utility or boot from a floppy disk. See page 2-6 for details. ASUS Q-Fan technology The ASUS Q-Fan technology smartly adjusts the CPU fan speed according to the system loading to ensure quiet, cool, and efficient operation. C.P.R. (CPU Parameter Recall) The C.P.R.
ASUS DH Remote™ (Only for P5V-VM DH) The ASUS DH Remote™ is a convenient PC remote controller that gives users unprecedented control over their PCs from the comfort of their couches. With the touch of a button, users can instantly operate the following functions: P o w e rr: Turns the computer on/off. Q u i c k P o w e rr: Puts the computer quickly into sleep mode. N o i s e O f ff: Reduces the noise coming from the computer.
1.4 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Use a grounded wrist strap or touch a safely grounded object or to a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity • Hold components by the edges to avoid touching the ICs on them.
1.5 Motherboard overview Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components. 1.5.1 Placement direction When installing the motherboard, make sure that you place it into the chassis in the correct orientation.
1.5.3 P5VD2-MX/P5V-VM DH Motherboard layout ESATA PS/2KBMS T: Mouse B: Keyboard Super I/O 21.8cm (8.6in) KBPWR PARALLEL PORT CPU_FAN LAN_USB34 VIA P4M890 Top:Line In Center:Line Out Below:Mic In FLOPPY SATA_A WIFI ® SEC_IDE USB9 PCIEX16 JMicron JMB363 CR2032 3V Lithium Cell CMOS Power RTL8201CL CD VIA VT8237A PCI1 AUX 4Mb BIOS PCIE1 24.5cm (9.
1.6 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA775 socket designed for the Intel® Core™2 Duo/Pentium® D/ Pentium® 4/Celeron® processor in the 775-land package. 1.6.1 • Your boxed Intel® Core™2 Duo/Pentium® D/Pentium® 4/Celeron® LGA775 processor package should come with installation instructions for the CPU, fan and heatsink assembly. If the instructions in this section do not match the CPU documentation, follow the latter.
2. Press the load lever with your thumb (A) and move it to the left (B) until it is released from the retention tab. PnP Cap Retention tab A Load lever B This side of the cam box should face you. To prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU. 3. Lift the load lever in the direction of the arrow to a 135º angle. 4. Lift the load plate with your thumb and forefinger to a 100º angle (A), then push the PnP cap from the load plate window to remove (B).
6. Close the load plate (A), then push the load lever (B) until it snaps into the retention tab. A B The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU! Notes on Intel® Hyper-Threading Technology • This motherboard supports Intel® Pentium® 4 CPUs in the 775-land package with Hyper-Threading Technology. • Hyper-Threading Technology is supported under Windows® XP/2003 Server and Linux 1.7.
1.6.2 Installling the CPU heatsink and fan The Intel® Pentium® 4 LGA775 processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. • Install the motherboard to the chassis before you install the CPU fan and heatsink assembly • When you buy a boxed Intel® Pentium® 4 processor, the package includes the CPU fan and heatsink assembly. If you buy a CPU separately, make sure that you use only Intel®-certified multi-directional heatsink and fan.
2. 3. Push down two fasteners at a time in a diagonal sequence to secure the heatsink and fan assembly in place. A B B A B A A B When the fan and heatsink assembly is in place, connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN. CPU_FAN GND CPU FAN PWR CPU FAN IN CPU FAN PWM ® CPU fan connector Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector.
1.6.3 Uninstalling the CPU heatsink and fan To uninstall the CPU heatsink and fan: 1. Disconnect the CPU fan cable from the connector on the motherboard labeled CPU_FAN. 2. Rotate each fastener counterclockwise. 3. Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and fan assembly from the motherboard.
4. Remove the heatsink and fan assembly from the motherboard. 5. Rotate each fastener clockwise to reset the orientation. Narrow end of the groove The narrow end of the groove should point outward after resetting. (The photo shows the groove shaded for emphasis.
1.7 System memory 1.7.1 Overview The motherboard comes with two Double Data Rate 2 (DDR2) Dual Inline Memory Modules (DIMM) sockets. A DDR2 module has the same physical dimensions as a DDR DIMM but has a 240-pin footprint compared to the 184-pin DDR DIMM. DDR2 DIMMs are notched differently to prevent installation on a DDR DIMM socket. The figure illustrates the location of the DDR2 DIMM sockets: 240-pin DDR2 DIMM sockets 1.7.
DDR2 533 Qualified Vendors List Size 256MB 1-18 Vendor KINGSTON Brand N/A V V 512MB KINGSTON 1024MB KINGSTON HY5PS56821F-C4 D6408TE7BL-37 N/A N/A DS DS KVR533D2N4/512 KVR533D2N4/1G V V V V 2048MB KINGSTON E1108AA-5C-E N/A DS KVR533D2N4/2G V V 512MB K4T51083QB-GCD5 N/A SS M378T6553BG0-CD5 V V V SAMSUNG Side(s) Component SS KVR533D2N4/256 DIMM support A B Model E5116AB-5C-E 256MB SAMSUNG K4T56083QF-GCD5 N/A SS M378T3253FG0-CD5 V 512MB 256MB SAMSUNG MICRON K4T56083QF-GCD
Legend: S i d e ( s ) : S S - Single-sided D S - Double-sided DIMM support: A - Supports one module inserted in any slot as Single-channel memory configuration B - Supports one pair of modules inserted into yellow slots as one pair of Singlechannel memory configuration 1.7.3 Installing a DIMM Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components. 2 1.
1.8 Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. 1.8.1 Installing an expansion card To install an expansion card: 1.
1.8.
1.8.4 PCI slots The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The figure shows a LAN card installed on a PCI slot. 1.8.5 PCI Express x1 slot This motherboard supports PCI Express x1 network cards, SCSI cards and other cards that comply with the PCI Express specifications. The figure shows a network card installed on the PCI Express x1 slot. • • 1.8.6 slot PCI-E x1 and eSATA cannot be used simultaneously.
1.9 1. Jumpers Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the onboard battery. 3.
2. Keyboard power (3-pin KBPWR) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) to wake up the computer when you press a key on the keyboard (the default is the Space Bar). This feature requires an ATX power supply that can supply at least 1A on the +5VSB lead, and a corresponding setting in the BIOS. KBPWR 1 2 2 3 +5V (Default) +5VSB ® Keyboard power setting 3.
Default for P5VD2-MX Status USBPW12 USBPW32 +5VSB • • +5V - - USBPW56 USBPW78 • • Default for P5V-VM DH Status USBPW12 USBPW32 USBPW56 USBPW78 +5VSB • • • • +5V - - - - • USB1 and USB2 ports are only for P5VD2-MX. • USB9 port is only for P5V-VM DH. • For P5V-VM DH, USBPW12 jumper controls USB 9 port. • The USB device wake-up feature requires a power supply that can provide 500mA on the +5VSB lead for each USB port; otherwise, the system would not power up.
1.10 Connectors 6 1.10.1 Rear panel connectors 1 2 5 4 3 7 8 9 13 11 10 14 12 1 . P S / 2 m o u s e p o r t ( g r e e n ) . This port is for a PS/2 mouse. 2 . P a r a l l e l p o r t . This 25-pin port connects a parallel printer, a scanner, or other devices. 3 . L A N ( R J - 4 5 ) p o r t . This port allows connection to a Local Area Network (LAN) through a network hub. LAN port LED indications Status 4. 5. 6.
7. 8. 9. W I F I - A P S o l o L E D i n d i c a t o r ( O n l y f o r P 5 V - V M D H ) . The WIFIAP Solo comes with a green data transmission LED (AIR). Refer to the ASUS WiFi-AP Solo user guide. A n t e n n a j a c k ( O n l y f o r P 5 V - V M D H ). This port is on the onboard wireless LAN module that allows you to set up a wireless network and exchange information with other wireless devices without tangling cables and wires. Connect the moveable omni-directional antenna to this jack. U S B 2 .
1.10.2 Internal connectors 1. Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. Pin 5 on the connector is removed to prevent incorrect cable connection when using an FDD cable with a covered Pin 5. FLOPPY ® PIN 1 NOTE: Orient the red markings on the floppy ribbon cable to PIN 1.
2. Primary/Secondary IDE connectors (40-1 pin PRI_IDE [blue]; 40-1 pin SEC_IDE [black]) The onboard IDE connectors are for Ultra DMA 133/100/66 signal cables. There are three connectors on each Ultra DMA 133/100/66 signal cable: blue, black, and gray. Connect the blue connector to the motherboard's IDE connector, then select one of the following modes to configure your device(s).
3. Serial ATA connectors (7-pin SATA1, SATA2) These connectors are for the Serial ATA signal cables for Serial ATA 1.5 Gb/s hard disk drives. If you installed Serial ATA hard disk drives, you can can create a RAID 0, RAID 1, and JBOD configuration through the onboard VIA VT8237A RAID controller.
5. CPU and Chassis fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN) The fan connectors support cooling fans of 350mA~740mA (8.88W max.) or a total of 1A~2.22A (26.64W max.) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components.
7. ATX power connectors (24-pin EATXPWR, 4-pin ATX12V) These connectors are for an ATX power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. • Do not forget to connect the 4-pin ATX +12 V power plug; otherwise, the system will not boot up. • Use a PSU with a minimum power rating of 300 W on this motherboard.
9. Internal audio connectors (4-pin CD, AUX) These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner, MPEG card or modem. ® CD(Black) AUX(White) Right Audio Channel Ground Ground Left Audio Channel Internal audio connectors 1 USB 2.0 connectors USB78 USB+5V USB_P5USB_P5+ GND USB56 1 USB+5V USB_P7USB_P7+ GND ® USB+5V USB_P8USB_P8+ GND NC USB+5V USB_P6USB_P6+ GND NC 1 0 . USB connectors (10-1 pin USB56, USB78) These connectors are for USB 2.0 ports.
1 1 . Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either High Definition Audio or legacy AC ‘97 audio standard. Connect one end of the front panel audio I/O module cable to this connector.
1 3 . MP3-In connector (4-pin MP3IN [red]) (Only for P5V-VM DH) This connector is for the MP3-In module that allows you to connect your MP3 player to the speakers of the computer. For more information, refer to the MP3_In™ quick installation guide for details. MP3IN ® Right Audio Channel Ground Ground Left Audio Channel MP3 connector • The MP3-In module is bundled with the motherboard package.
1 4 . System panel connector (20-1 pin F_PANEL) This connector supports several chassis-mounted functions. SPEAKER +5V Ground Ground Speaker PLED- PLED+ PLED IDE_LED Reset Ground PWR Ground IDE_LED+ IDE_LED- PANEL ® RESET PWRSW * Requires an ATX power supply. System panel connector The sytem panel connector is color-coded for easy connection. Refer to the connector description below for details. • System power LED (Green 3-pin PLED) This 3-pin connector is for the system power LED.
This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
2.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. A S U S U p d a t e (Updates the BIOS in Windows® environment.) A S U S E Z F l a s h (Updates the BIOS using a floppy disk during POST.) A w a r d B I O S F l a s h U t i l i t y (Updates the BIOS in DOS mode using a bootable floppy disk.) 1. 2. 3.
Updating the BIOS through the Internet To update the BIOS through the Internet: 1. Launch the ASUS Update utility from the Windows® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate e. The ASUS Update main window appears. 2. Select U p d a t e B I O S f r o m t h e I n t e r n e t option from the drop-down menu, then click N e x tt. ASUS P5VD2-MX/P5V-VM DH 3. Select the ASUS FTP site nearest you to avoid network traffic, or click A u t o S e l e c tt. Click N e x tt.
4. From the FTP site, select the BIOS version that you wish to download. Click Next. 5. Follow the screen instructions to complete the update process. The ASUS Update utility is capable of updating itself through the Internet. Always update the utility to avail all its features. Updating the BIOS through a BIOS file To update the BIOS through a BIOS file: 1. 2.
2.1.2 1. Creating a bootable floppy disk Do either one of the following to create a bootable floppy disk. DOS environment a. Insert a 1.44MB floppy disk into the drive. b. At the DOS prompt, type format A:/S then press . Windows® XP environment a. Insert a 1.44 MB floppy disk to the floppy disk drive. b. Click S t a r t from the Windows® desktop, then select M y C o m p u t e rr. c. Select the 3 1/2 Floppy Drive icon. d. Click F i l e from the menu, then select F o r m a tt.
2.1.3 ASUS EZ Flash utility The ASUS EZ Flash feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS-based utility. The EZ Flash utility is built-in the BIOS chip so it is accessible by pressing + during the Power-On Self Tests (POST). To update the BIOS using EZ Flash: 1. Visit the ASUS website (www.asus.com) to download the latest BIOS file for the motherboard. 2.
2.1.4 Updating the BIOS The Basic Input/Output System (BIOS) can be updated using the AwardBIOS Flash Utility. Follow these instructions to update the BIOS using this utility. 1. Download the latest BIOS file from the ASUS web site. Rename the file to P 5 V D 2 - M X . B I N and save it to a floppy disk. Save only the updated BIOS file in the floppy disk to avoid loading the wrong BIOS file. 2. Copy the AwardBIOS Flash Utility (awdflash.
7. Press when the utility prompts you to save the current BIOS file. The following screen appears. 8. The utility verifies the BIOS file in the floppy disk and starts flashing the BIOS file. AwardBIOS Flash Utility for ASUS V1.14 (C) Phoenix Technologies Ltd. All Rights Reserved For NF-CK804-P5VD2-MX-00 DATE: 04/13/2006 Flash Type - PMC Pm49FL004T LPC/FWH File Name to Program: 0104.
2.1.4 ASUS CrashFree BIOS 2 utility The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can update a corrupted BIOS file using the motherboard support CD or the floppy disk that contains the updated BIOS file. • Prepare the motherboard support CD or the floppy disk containing the updated motherboard BIOS before using this utility.
Recovering the BIOS from the support CD To recover the BIOS from the support CD: 1. Remove any floppy disk from the floppy disk drive, then turn on the system. 2. Insert the support CD to the optical drive. 3. The utility displays the following message and automatically checks the floppy disk for the original or updated BIOS file. Bad BIOS checksum. Starting BIOS recovery... Checking for floppy...
2.2 BIOS setup program This motherboard supports a programmable firmware chip that you can update using the provided utility described in section “2.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you can change the configuration of your computer in the future.
2.2.1 BIOS menu screen Menu items Menu bar Main Advanced Configuration fields Phoenix-Award BIOS CMOS Setup Utility Power Boot Exit System Time System Date 15 : 30 : 36 Mon, Mar 2 2006 Legacy Diskette A: [1.44M, 3.5 in.] Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave SATA 1 SATA 2 HDD SMART Monitoring Installed Memory Usable Memory ↑↓ : Select Item →← ←: Select Menu F1:Help ESC: Exit Sub-menu items 2.2.
2.2.3 Legend bar At the bottom of the Setup screen is a legend bar. The keys in the legend bar allow you to navigate through the various setup menus. The following table lists the keys found in the legend bar with their corresponding functions.
2.2.7 Pop-up window Select a menu item then press to display a pop-up window with the configuration options for that item. Main Advanced Phoenix-Award BIOS CMOS Setup Utility Power Boot Exit System Time System Date 15 : 30 : 36 Mon, Mar 03 2006 Legacy Diskette A: [1.44M, 3.5 in. Select Menu Item Specific Help A: Primary IDE MasterLegacy Diskette [ST321122A] Primary IDE Slave [ASUS CDS520/A] Disabled [None] ..... [ ] Secondary IDE Master 720K , 3.5 [None] in. .....
2.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information. Refer to section “2.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them. Main Advanced Phoenix-Award BIOS CMOS Setup Utility Power Boot Exit System Time System Date 15 : 30 : 36 Mon, Mar 03 2005 Legacy Diskette A: [1.44M, 3.5 in.
2.3.4 Primary and Secondary IDE Master/Slave While entering Setup, the BIOS automatically detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press to display the IDE device information.
Capacity Displays the auto-detected hard disk capacity. This item is not configurable. Cylinder Shows the number of the hard disk cylinders. This item is not configurable. Head Shows the number of the hard disk read/write heads. This item is not configurable. Sector Shows the number of sectors per track. This item is not configurable. PIO Mode [Auto] Sets the PIO mode for the IDE device.
2.3.5 SATA 1/2 While entering Setup, the BIOS automatically detects the presence of Serial ATA devices. There is a separate sub-menu for each SATA device. Select a device item then press to display the SATA device information. Phoenix-Award BIOS CMOS Setup Utility Main SATA 1 Select Menu Extended IDE Drive Access Mode [Auto] [Auto] Item Specific Help Capacity 0 MB Selects the type of fixed disk connected to the system.
Head Shows the number of the hard disk read/write heads. This item is not configurable. Landing Zone Shows the number of landing zone per track. This item is not configurable. Sector Shows the number of sectors per track. This item is not configurable. After entering the IDE hard disk drive information into BIOS, use a disk utility, such as FDISK, to partition and format new IDE hard disk drives. This is necessary so that you can write or read data from the hard disk.
2.4 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Take caution when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. Main Advanced Phoenix-Award BIOS CMOS Setup Utility Power Boot Exit CPU Configuration Chipset PCIPnP Onboard Device Configuration USB Configuration F1:Help ESC: Exit 2.4.1 ↑↓ : Select Item →← →←: Select Menu Select Menu Item Specific Help Press [Enter] to set.
CPU L1 & L2 Cache [Enabled] Configuration options: [Disabled] [Enabled] 2.4.
Active to Precharge(Tras) [07T] Configuration options: [05T] [06T]...[20T] Active to CMD(Trcd) [4T] Configuration options: [2T] [3T] [4T] [5T] REF to ACT/REF(Trfc) [20T/21T] Configuration options: [07T/08T] [08T/09T] [09/10T]...
Primary Display Adapter [PCI-E] Allows you to select which graphics controller to use as the primary boot device. Configuration options: [PCI] [AGP] [PCI-E] VGA Share Memory Size [64M] Configuration options: [Disabled] [16M] [32M] [64M] 2.4.
IRQ Resources This sub-menu is activated only when the R e s o u r c e s C o n t r o l l e d B y item is set to Manual.
2.4.
Serial Port1 Address [3F8/IRQ4] Allows you to select the Serial Port1 base address. Configuration options: [Disabled] [3F8/IRQ4] [2F8/IRQ3] [3E8/IRQ4] [2E8/IRQ3] [Auto] Parallel Port Address [378/IRQ7] Allows you to select the Parallel Port address. Configuration options: [Disabled] [378/IRQ7] [278/IRQ5] [3BC/IRQ7] Parallel Port Mode [Bi-Directional] Allows you to select the Parallel Port mode.
2.4.5 USB Configuration Phoenix-Award BIOS CMOS Setup Utility Advanced USB Configuration Select Menu Item Specific Help USB Contoller [Enabled] USB 2.0 Controller [Enabled] USB Legacy support [Auto] Enable or Disable USB 1.1 and 2.0 Controller USB Controller [Enabled] Allows you to enable or disable the onchip USB controller. Configuration options: [Disabled] [Enabled] USB 2.0 Controller [Enabled] Allows you to enable or disable the USB 2.0 controller.
2.5 Power menu The Power menu items allow you to change the settings for the Advanced Configuration and Power Interface (ACPI) and the Advanced Power Management (APM). Select an item then press to display the configuration options. Main Advanced Phoenix-Award BIOS CMOS Setup Utility Power Boot Exit ACPI Suspend Type ACPI APIC support Select Menu [S1&S3] Enabled Item Specific Help APM Configuration Hardware Monitor F1:Help ESC: Exit 2.5.1 Select the ACPI state used for System Suspend.
Power On By PS/2 Mouse [Disabled] When set to [Enabled], this parameter allows you to use the PS/2 mouse to turn on the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Double Click] Power On By PS/2 Keyboard [Disabled] Allows you to disable the Power On by PS/2 keyboard function or set specific keys on the PS/2 keyboard to turn on the system.
Alarm Time (hh:mm) To set the time of alarm: 1. Highlight this item and press to display a pop-up menu for the hour field. 2. Key-in a value (Min=0, Max=23), then press . 3. Press to move to the minutes field then press . 4. Key-in a minute value (Min=0, Max=59), then press . 5. Press to move to the seconds field then press . 6. Key-in a value (Min=0, Max=59), then press .
2.5.4 Hardware Monitor The items in this sub-menu displays the hardware monitor values automatically detected by the BIOS. It also allows you to change CPU Q-Fan feature-related parameters. Select an item then press to display the configuration options. Phoenix-Award BIOS CMOS Setup Utility Power Hardware Monitor Q-Fan Controller [Enabled] Vcore Voltage [1.56V] 3.3V Voltage [3.30V] 5V Voltage [5.05V] 12V Voltage [11.
Start Up Temperature(ºC) [50] Fan will start up when the temperature is over the set value. Configuration options: [Min=0] [Max=100] Full Speed Temperature(ºC) [70] Fan will run at full speed when the temperature is over the set value. Configuration options: [Min=0] [Max=100] Start Up PWM [60] Sets the PWM value when the fan starts up. Configuration options: [Min=0] [Max=127] Slope PWM [4 PWM/ºC] Sets the PWM value when the temperature increases one value.
2.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press to display the sub-menu. Main Phoenix-Award BIOS CMOS Setup Utility Power Boot Exit Advanced Boot Device Priority Removable Drives Hard Disk Drives Boot Settings Configuration Security F1:Help ESC: Exit 2.6.1 ↑↓ : Select Item →←: Select Menu →← Select Menu Item Specific Help Press [Enter] to Set.
2.6.3 Hard Disk Drives Phoenix-Award BIOS CMOS Setup Utility Boot Hard Disk Drives Select Menu Item Specific Help 1. Bootable Add-in Cards 1. Bootable Add-in Cards Allows you to assign bootable add-in cards attached to the system. 2.6.
Bootup Num-Lock [On] Allows you to select the power-on state for the NumLock. Configuration options: [Off] [On] Typematic Rate Setting [Disabled] Allows you to set the keystroke rate. Enable this item to configure the T y p e m a t i c R a t e ( C h a r s / S e c ) and the T y p e m a t i c D e l a y ( M s e c )).
2.6.5 Security Phoenix-Award BIOS CMOS Setup Utility Boot Boot Settings Configuration Supervisor Password Clear User Password Clear Password Check [Setup] Select Menu Item Specific Help Supervisor Password User Password These fields allow you to set passwords: To set a password: 1. Select an item then press . 2. Type in a password using a combination of a maximum of eight (8) alpha-numeric characters, then press . 3.
Password Check This field requires you to enter the password before entering the BIOS setup or the system. Select [Setup] to require the password before entering the BIOS Setup. Select [System] to require the password before entering the system.
2.7 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items. Main Advanced Phoenix-Award BIOS CMOS Setup Utility Power Boot Exit Exit & Save Changes Exit & Discard Changes Load Setup Default Discard Changes F1:Help ESC: Exit and Exit ↑↓ : Select Item →←: Select Menu →← Select Menu Item Specific Help This option save data to CMOS and exiting the setup menu.
Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press , a confirmation window appears. Select Y E S to load default values. Select E x i t & S a v e C h a n g e s or make other changes before saving the values to the non-volatile RAM. Discard Changes This option allows you to discard the selections you made and restore the previously saved values.
2-40 Chapter 2: BIOS setup
This chapter describes the contents of the support CD that comes with the motherboard package.
3.1 Installing an operating system This motherboard supports Windows® 2000/XP/2003 Server operating systems (OS). Always install the latest OS version and corresponding updates to maximize the features of your hardware. 3.2 • Motherboard settings and hardware options vary. Use the setup procedures presented in this chapter for reference only. Refer to your OS documentation for detailed information.
3.2.2 Drivers menu The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. VIA 4 in 1 Drivers Installs the VIA 4 in 1 Drivers. VIA/S3G UniChrome Family Display Driver Installs the VIA/S3G UniChrome Family Display Driver. The VIA/S3G UniChrome Family Display Driver item appears only when you use onboard VGA.
3.2.3 Utilities menu The Utilities menu shows the applications and other software that the motherboard supports. ASUS PC Probe II This smart utility monitors the fan speed, CPU temperature, and system voltages, and alerts you of any detected problems. This utility helps you keep your computer in healthy operating condition. ASUS Update The ASUS Update utility allows you to update the motherboard BIOS in a Windows® environment.
3.2.4 Make Disk menu The Make Disk menu allows you to make a RAID driver disk. Make VIA VT8237 RAID Driver Disk Allows you to create a VIA VT8237 RAID driver disk.0 Make JMicron JMB36X 32/64 bit RAID Driver Allows you to create a JMicron JMB36X RAID driver disk for a 32/64-bit system. 3.2.5 Manuals menu The Manuals menu contains a list of supplementary user manuals. Click an item to open the folder of the user manual. Most user manual files are in Portable Document Format (PDF).
Intel LGA775 CPU install User’s Manual Allows you to open the Intel® LGA775 CPU installation guide. VIA VT8237 RAID User’s Manual Allows you to open the VIA VT8237 RAID user’s manual. JMicron RAID AP Utility User Manual Allows you to open the JMicron RAID AP user’s manual. JMicron RAID BIOS User Manual Allows you to open the JMicron RAID BIOS user’s manual. RTL8187 Wireless LAN User’s Manual Allows you to open the RTL8187 Wireless LAN user’s manual. 3.2.
3.3 RAID configurations The motherboard supports the following RAID configurations. RAID 0 (Data striping) optimizes two identical hard disk drives to read and write data in parallel, interleaved stacks. Two hard disks perform the same work as a single drive but at a sustained data transfer rate, double that of a single disk alone, thus improving data access and storage. Use of two new identical hard disk drives is required for this setup.
If you want to boot the system from a hard disk drive included in a RAID set, copy first the RAID driver from the support CD to a floppy disk before you install an operating system to a selected hard disk drive. Refer to section “3.4 Creating a RAID driver disk” for details. 3.3.1 Installing hard disks The motherboard supports RAID function on Serial ATA hard disk drives. For optimal performance, install identical drives of the same model and capacity when creating a disk array.
Create Array From the VIA RAID BIOS utility main menu, select Create Array then press . The main menu items on the upper-left corner of the screen are replaced with create array menu options. VIA Tech. VT8251 Series SATA RAID BIOS Ver 1.
4. Press to confirm or to return to the configuration options. If you selected , proceed to step 9. 5. Select Select Disk Drives, then press . Use arrow keys to select disk drive, then press to mark selected drive. An asterisk appears before a selected drive. 6. Select Block Size, then press to set array block size. A list of valid array block sizes are displayed on a pop-up menu. TIP: For server systems, use of a lower array block size is recommended.
3. From this point, you can auto-configure the RAID array by selecting Auto Setup for Data Security or manually configure the RAID array for mirrored sets. If you want to auto-configure, proceed to the next step, otherwise, skip to step 6. 4. Select Auto Setup for Data Security and press . The following confirmation message appears. Auto create array will destroy all data on disks, Continue? (Y/N) 5. Press to confirm or to return to the configuration options.
3.3.2 JMicron® RAID Configuration The JMicron® Serial ATA controller allows you to configure RAID 0 and RAID 1 sets on the external Serial ATA hard disk drives. Before creating a RAID set Prepare the following items: 1. Two HDDs, preferably with the same model and capacity. 2. A write-enabled floppy disk 3. Microsoft® Windows® OS installation disk (Windows 2000/XP/2003) 4. Motherboard support CD with JMB363 driver Complete the following steps before you create a RAID set: 1.
Entering the JMB363 RAID BIOS utility 1. During POST, press to enter the JBM363 RAID BIOS menu. JMicron Technology Corp. PCI-to-SATA II/IDE RAID Controller BIOS v0.97 Copyright (C) 2004-2005 JMicron Technology http://www. jmicron.com HDD0 : HDS722516VLSA80 HDD1 : HDS722516DLA380 164 GB Non-RAID 164 GB Non-RAID Press to enter RAID Setup Utility... 2. The main JMB363 RAID BIOS menu appears. 3. Use the arrow keys to move the color bar and navigate through the items.
2. 3. When the Level item is highlighted, use the up/down arrow key to select the RAID set that you want to create.
5. When done, press to confirm the creation of the RAID set. A dialogue box appears to confirm the action. Press to confirm; otherwise, press . JMicron Technology Corp. PCI-to-SATA II/IDE RAID Controller BIOS v0.
Deleting a RAID set 1. In the main JMB363 RAID BIOS menu, highlight Delete RAID Disk Drive using the up/down arrow key then press . [Main Menu] Create RAID Disk Drive Delete RAID Disk Drive Revert HDD to Non-RAID Repair Mirror Conflict Save and Exit Setup Exit Without Saving 2. Use the space bar to select the RAID set you want to delete. A selected set shows a delete the set. 3. sign before it. Press the key to A dialogue box appears to confirm the action.
Resetting disks to non-RAID An HDD that has been previously configured as part of another RAID set in another platform is called a broken RAID HDD. When you install a broken RAID HDD, you cannot select this HDD when configuring a RAID set through the JMB363 utility. To reset disks to non-RAID: 1. In the main JMB363 RAID BIOS menu, highlight Revert HDD to non‑RAID using the up/down arrow key then press .
Repairing a Mirror conflict A Mirror conflict occurs when one or both disks in a RAID 1 (Mirror) configuration are unplugged from the system, then plugged in again. Since both disks contain exactly the same data, the system will be unable to determine which of the two is the source drive. This option allows you to set the source drive and rebuild the Mirror drive according to the contents of the source drive. To repair a Mirror conflict: 1.
Saving the settings and exiting setup When you have finished, highlight Save & Exit Setup using the up/down arrow key then press to save the current RAID configuration and exit the JMB363 RAID BOS utility. A dialogue box appears to confirm the action. Press to confirm; otherwise, press to return to the JMB RAID BIOS menu.
3.4 Creating a RAID driver disk A floppy disk with the RAID driver is required when installing Windows® 2000/XP operating system on a hard disk drive that is included in a RAID set. To create a RAID driver disk: 1. Place the motherboard support CD into the CD-ROM drive. 2.