Motherboard P5VDC-TVM
E2569 First Edition April 2006 Copyright © 2006 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Notices.................................................................................................. v Safety information............................................................................... vi P5VDC-TVM specifications summary...................................................vii Chapter 1: Product introduction 1.1 Before you proceed............................................................... 1-2 1.2 Motherboard overview.......................................................
Contents Chapter 2: BIOS Setup 2.1 iv BIOS setup program............................................................... 2-2 2.2 BIOS menu screen.................................................................. 2-3 2.3 Standard BIOS Features......................................................... 2-5 2.4 Advanced BIOS Features........................................................ 2-9 2.5 Integrated Peripherals.......................................................... 2-11 2.
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
P5VDC-TVM specifications summary CPU LGA775 socket for Intel® Pentium® 4/Celeron processor Compatible with Intel® Mainstream/Value FMB processors Supports Intel® Hyper-Threading Technology Chipset Northbridge: VIA P4M800 PRO Southbridge: VIA VT8237R Plus Front Side Bus 800/533 MHz Memory 2 x 240-pin DIMM sockets support unbufferred and non-ECC 533 MHz DDR memory modules Expansion slots 3 x PCI slots Storage VIA VT8237R Plus Southbridge supports: - 4 x Ultra ATA 133/100/66 hard disk
P5VDC-TVM specifications summary Internal connectors 1 x Floppy disk drive connector 2 x IDE connectors 2 x Serial ATA connectors 1 x CPU fan connector 1 x Chassis fan connector 4 x USB 2.0 connectors 1 x 20-pin ATX power connector 1 x 4-pin ATX 12 V power connector 1 x Front panel audio connector 1 x CD/AUX audio connector 1 x S/PDIF Out connector 1 x Serial port connector System panel connector Power requirement ATX power supply (with 20-pin and 4-pin 12 V plugs) ATX 12 V 2.
This chapter describes the motherboard features and the new technologies it supports.
1.1 Before you proceed Take note of the following precautions before you install components into the system. • Unplug the power cord from the wall socket before touching any component. • Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity. • Hold components by the edges to avoid touching the ICs on them.
1.2 Motherboard overview Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components. 1.2.1 Placement direction When installing the motherboard, make sure that you place it into the chassis in the correct orientation.
1.2.3 Motherboard layout 24.5cm (9.6in) CHA_FAN CPU_FAN COM1 Super I/O LAN_USB34 Top:Rear Speaker Out Center: Side Speaker Out Below: Center/Subwoofer VIA P4M800 PRO CD ® PRI_IDE 22.9cm (9.
1.2.4 Layout contents Slots Page 1. 1-20 PCI slots Jumpers Page 1. Clear RTC RAM (3-pin CLRTC) 1-21 2 Flash Write Protection (2-pin FWP) 1-22 Rear panel connectors Page 1. PS/2 mouse port (green) 1-23 2. Parallel port 1-23 3. LAN (RJ-45) port 1-23 4. Line In port (light blue) 1-23 5. Line Out port (lime) 1-23 6. Microphone port (pink) 1-23 7. USB 2.0 ports 3 and 4 1-24 8. USB 2.0 ports 1 and 2 1-24 9. Video Graphics Adapter (VGA) port 1-24 10.
1.3 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA775 socket designed for the Intel® Pentium® 4 processor in the 775-land package. 1.3.1 • Your boxed Intel® Pentium® 4 LGA775 processor package should come with installation instructions for the CPU, heatsink, and the retention mechanism. If the instructions in this section do not match the CPU documentation, follow the latter.
2. Press the load lever with your thumb (A) and move it to the left (B) until it is released from the retention tab. Retention tab PnP Cap A Load lever B This side of the cam box should face you. To prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU. 3. Lift the load lever in the direction of the arrow to a 135º angle. 4. Lift the load plate with your thumb and forefinger to a 100º angle (A), then push the PnP cap from the load plate window to remove (B).
6. Close the load plate (A), then push the load lever (B) until it snaps into the retention tab. A B The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent benting the connectors on the socket and damaging the CPU. Notes on Intel ® Hyper-Threading Technology • This motherboard supports Intel® Pentium® 4 CPUs in the 775-land package with Hyper-Threading Technology. • Hyper-Threading Technology is supported under Windows® XP/2003 Server and Linux 2.4.
1.3.2 Installing the CPU heatsink and fan The Intel Pentium® 4 LGA775 processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. ® • Install the motherboard to the chassis before you install the CPU fan and heatsink assembly. • When you buy a boxed Intel® Pentium® 4 processor, the package includes the CPU fan and heatsink assembly.
2. 3. Push down two fasteners at a time in a diagonal sequence to secure the heatsink and fan assembly in place. A B B A B A A B Connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN. ® P5VDC-TVM CPU_FAN GND CPU FAN PWR CPU FAN IN CPU FAN PWM P5VDC-TVM CPU FAN Connector Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector.
1.3.3 Uninstalling the CPU heatsink and fan To uninstall the CPU heatsink and fan: 1. Disconnect the CPU fan cable from the connector on the motherboard. 2. Rotate each fastener counterclockwise. 3. Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and fan assembly from the motherboard.
4. Remove the heatsink and fan assembly from the motherboard. 5. Rotate each fastener clockwise to reset the orientation. Narrow end of the groove When reset, each fastener should be oriented as shown, with the narrow groove directed outward.
1.4 System memory 1.4.1 DIMM sockets location The motherboard comes with two 240-pin Double Data Rate 2 (DDR2). DDR2_A1 DDR2_B1 ® P5VDC-TVM The following figure illustrates the location of the sockets: P5VDC-TVM DDR2 DIMM Sockets 1.4.2 Memory Configurations You may install 256 MB, 512 MB and 1 GB unbuffered and non‑ECC DDR2 DIMMs into the DIMM sockets using the memory configurations in this section. • Always install DIMMs with the same CAS latency.
DDR2 (533 MHz) Qualified Vendors List Size Vendor Hynix HYMP564U64AP8-C3 Brand Side(s) SS HY5PS12821A 512MB Hynix • HYMP564U64AP8-Y4 AA Hynix SS HY5PS12821A 256MB • Infineon HYS64T32000HU-3.7-A N/A SS HYB18T512160AF-3.7 • 256MB Infineon HYS64T32000HU-3.7-B N/A SS HYB18T5121608BF-3.7 • 512MB Infineon HYS64000GU-3.7-A HY SS HYB18T512 • 512MB Infineon HYS64T64000GU-3.7-A N/A SS HYB18T512800AC37 • 512MB Infineon HYS64T64000HU-3.
1.4.3 Installing a DDR2 DIMM Unplug the power supply before inserting or removing DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components. 2 To install a DDR2 DIMM: 1. Unlock a DDR2 DIMM socket by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. 3.
1.5 Expansion slots In the future, you may need to install expansion cards. The following sub‑sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. 1.5.1 Installing an expansion card To install an expansion card: 1.
1.5.
1.5.4 PCI slots This motherboard has three PCI slots. The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The figure shows a LAN card installed on a PCI slot.
1.6 1. Jumpers Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the onboard battery. 3. Move the jumper cap from pins 1-2 (default) to pins 2-3.
2. Flash Write Protection (FWP) Place the jumper cap on this jumper to write protect the BIOS. If you need to update your BIOS, remove the jumper cap. ® P5VDC-TVM A warning message “Please make sure whether lockout jumper is set to correct or not.” appears when you flash the BIOS with the jumper cap. Remove the jumper cap before you update your BIOS. .
1.7 Connectors 1.7.1 Rear panel connectors 1 2 3 4 5 6 11 10 8 9 7 1. PS/2 mouse port (green). This port is for a PS/2 mouse. 2. Parallel port. This 25-pin port connects a parallel printer, a scanner, or other devices. 3. LAN (RJ-45) port. This port allows 10/100 Mbps connection to a Local Area Network (LAN) through a network hub. Refer to the table below for the LAN port LED indications.
Audio 2, 4, or 6-channel configuration Port Headset 2-channel Light Blue 4-channel 6-channel Line In Rear Speaker Out Rear Speaker Out Lime Line Out Front Speaker Out Front Speaker Out Pink Mic In Mic In Center/Subwoofer 7. USB 2.0 ports 3 and 4. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. 8. USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. 9.
2. IDE connectors (40-1 pin PRI_IDE, SEC_IDE) These connectors are for Ultra DMA 133/100/66 signal cables. The Ultra DMA 133/100/66 signal cable has three connectors: a blue connector for the primary IDE connector on the motherboard, a black connector for an Ultra DMA 133/100/66 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 133/100/66 IDE master device (hard disk drive).
3. Serial ATA connectors (7-pin SATA1 [black], SATA2 [black]) These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives. SATA2 GND RSATA_RXN1 RSATA_RXP1 GND RSATA_TXN1 RSATA_TXP1 GND SATA1 P5VDC-TVM ® GND RSATA_RXN2 RSATA_RXP2 GND RSATA_TXN2 RSATA_TXP2 GND P5VDC-TVM SATA Connectors Important notes on Serial ATA • Install the Windows® 2000 Service Pack 4 or the Windows® XP Service Pack1 before using Serial ATA.
4. CPU and Chassis Fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN) The fan connectors support cooling fans of 350mA~740mA (8.88W max.) or a total of 1A~2.22A (26.64W max.) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components.
5. USB connectors (10-1 pin USB56, USB78) USB+5V USB_P10USB_P10 GND NC USB+5V USB_P6USB_P6+ GND NC P5VDC-TVM USB 2.0 Connectors 1 USB78 USB+5V USB_P5USB_P5+ GND USB56 1 USB+5V USB_P9USB_P9+ GND ® P5VDC-TVM These connectors are for USB 2.0 ports. Connect the USB/GAME module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed.
6. ATX power connectors (20-pin ATXPWR, 4-pin ATX12V) These connectors are for ATX power supply plugs. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. ATX12V ® P5VDC-TVM GND +12V DC GND +12V DC ATXPWR +12.0VDC +5VSB PWR_OK GND +5.0VDC GND +5.0VDC GND +3.3VDC +3.3VDC +5.0VDC +5.0VDC -5.0VDC GND GND GND PS_ON# GND -12.0VDC +3.
7. Front panel audio connector (10-1 pin FP_AUDIO) ® BLINE_OUT_L P5VDC-TVM AGND +5VA BLINE_OUT_R This connector is for a chassis-mounted front panel audio I/O module that supports legacy AC ‘97 audio standard. Connect one end of the front panel audio I/O module cable to this connector. MIC2 MICPWR Line out_R NC Line out_L FP_AUDIO P5VDC-TVM Front Panel Audio Connector 8. Serial port connector (10-1 pin COM2) ® P5VDC-TVM This connector is for a serial (COM) port.
9. Internal audio connectors (4-pin CD, AUX) These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner, or MPEG card. CD (black) ® P5VDC-TVM Internal Audio Connectors Left Audio Channel Ground Ground Right Audio Channel P5VDC-TVM Right Audio Channel Ground AUX Ground Left Audio Channel (white) 10. Digital audio connector (4-1 pin SPDIF_OUT) ® SPDIFOUT GND +5V P5VDC-TVM This connector is for additional Sony/Philips Digital Interface (S/PDIF) port(s).
11. System panel connector (10-1 pin F_PANEL) This connector supports several chassis-mounted functions. PWR GND F_PANEL IDE_LED+ IDE_LEDGround Reset ® P5VDC-TVM PWRSW IDE LED RESET P5VDC-TVM System Panel Connector • System power LED (2-pin PLED) This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode.
This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
2.1 BIOS setup program This motherboard supports a programmable firmware chip that you can update using the provided utility. Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup.” This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you can change the configuration of your computer in the future.
2.2 BIOS menu screen When you enter the BIOS, the following screen appears. The BIOS menu screen displays the items that allow you to make changes to the system configuration. To access the menu items, press the up/down/right/left arrow key on the keyboard until the desired item is highlighted, then press [Enter] to open the specific menu.
List box This box appears only in the opening screen. The box displays an initial list of configurable items in the menu you selected. Sub-menu Note that a right pointer symbol ( ) appears to the left of certain fields. This pointer indicates that you can display a sub-menu from this field. A sub-menu contains additional options for a field parameter. To display a sub-menu, move the highlight to the field and press . The sub‑menu appears.
2.3 Standard BIOS Features The Standard BIOS Features screen gives you an overview of the basic system information. Phoenix - Award BIOS CMOS Setup Utility Standard BIOS Features Date (mm:dd:yy) Time (hh:mm:ss) IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 1 Master IDE Channel 1 Slave SATA Channel 2 Master SATA Channel 3 Master Mon, Jan 24 2005 11 : 35 : 24 [ST320410A] [ASUS CD-S520/A] [None] [None] [None] [None] Drive A [1.44M, 3.5 in.
IDE HDD Auto-Detection [Press Enter] Allows auto-detection of the hard disk drive’s specifications. IDE Channel 0, 1 Master/Slave [Auto] Sets the selected channel as Master or Slave. Configuration options: [None] [Auto] [Manual] Access Mode [Auto] This item allows the user to select the sector addressing mode. CHS mode supports 528 MB hard disks. LBA (logical block addressing) mode supports hard disks up to 128 GB in size.
SATA Channel 2, 3 Master While entering Setup, the BIOS automatically detects the presence of Serial ATA devices. There is a separate sub-menu for each SATA device. Select a device item then press to display the SATA device information.
Head Shows the number of the hard disk read/write heads. This item is not configurable. Precomp Shows the number of precomp per track. This item is not configurable. Landing Zone Shows the number of landing zone per track. This item is not configurable. Sector Shows the number of sectors per track. This item is not configurable. After entering the IDE hard disk drive information into the BIOS, use a disk utility, such as FDISK, to partition and format new IDE hard disk drives.
2.4 Advanced BIOS Features The Advanced BIOS Features menu items allow you to change the advanced BIOS settings. Take caution when changing the settings of the Advanced BIOS Features items. Incorrect field values may cause the system to malfunction.
First/Second/Third/Fourth Boot Device Allows you to assign the boot device priority. Configuration options: [Floppy] [LS120] [Hard Disk] [CDROM] [ZIP] [USB-FDD] [USB-ZIP] [USB-CDROM] [LAN] [Disabled] Boot Up Floppy Seek [Disabled] When [Enabled], the BIOS will seek the flopy disk drive to determine whether the drive has 40 or 80 tracks. Configuration options: [Disabled] [Enabled] Boot Up Num-Lock Status [On] Allows you to select the power-on state for the NumLock.
2.5 Integrated Peripherals The Integrated Peripherals menu items allow you to change the onboard devices configuration settings.
IDE Primary, Secondary Master/Slave PIO [Auto] This option lets you set a PIO (Programmed Input/Output) mode for the IDE device. Modes 0 through 4 provide successive increase in performance. Configuration options: [Auto] [Mode 0] [Mode 1] [Mode 2] [Mode 3] [Mode 4] IDE Primary, Secondary Master/Slave UDMA [Auto] Ultra DMA capability allows improved transfer speeds and data integrity for compatible IDE devices. Set to [Disabled] to suppress Ultra DMA capability.
Onboard Device This sub-menu allows you to set the configurations for onboard devices. Select an item then press to edit. Phoenix - Award BIOS CMOS Setup Utility Onboard Device USB Controller USB 2.0 Controller USB Keyboard Support Onboard AC97 Audio Onboard LAN Device Onboard LAN Boot ROM : Move Enter:Select F5: Previous Values [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Disabled] Select Menu Item Specific Help Enable/Disable Onboard 1394 device support.
SuperIO Device This sub-menu allows you to set the configurations for SuperIO devices. Select an item then press to edit. Phoenix - Award BIOS CMOS Setup Utility SuperIO Device Onboard Serial Port 1 Onboard Serial POrt 2 Onboard Parallel Port Parallel Port Mode ECP Mode Use DMA : Move Enter:Select F5: Previous Values [3F8/IRQ4] [2F8/IRQ3] [378/IRQ7] [ECP] [3] Select Menu Item Specific Help Select Serial Port1 base address.
2.6 Power Management Setup The Power Management Setup menu items allow you to change the settings for the Advanced Power Management (APM) and Advanced Configuration and Power Interface (ACPI).
Resume by Ring [Enabled] Allows you to enable or disable system power up when the external modem receives a call while the computer is in soft-off mode. Configuration options: [Disabled] [Enabled] The computer cannot receive or transmit data until the computer and applications are fully running. Thus, connection cannot be made on the first try. Turning an external modem off and then back on while the computer is off causes an initialization string that turns the system power on.
2.7 PC Health Status The PC Health Status screen shows the motherboard CPU and fan temperatures, and allows you to set threshold levels for efficient system operation. Phoenix - Award BIOS CMOS Setup Utility PC Health Status CPU Temperature 38oC MB Temperature 37oC CPU Fan Speed 3835 RPM System Fan Speed 0 RPM VCORE Voltage 1.50 V 3.3 V voltage 3.34 V +5V in 5.19 V +13V in 11.
Start Up Temperature (ºC) [50] Allows you to set the fan start-up temperature. Configuration options: [0] [1] ~ [100] Full Speed Temperature (ºC) [70] Allows you to set the threshold temperature before the fan begins running at full speed. Configuration options: [0] [1] ~ [100] Start Up PWM [60] Sets the start-up Pulse Width Modulation (PWM) value when the fan starts running.
