Premium Motherboard P5WD2
E2086 Revised Edition V2 May 2005 Copyright © 2005 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Notices ................................................................................................ vi Safety information ............................................................................. vii About this guide ............................................................................... viii P5WD2 Premium specifications summary ............................................ x Chapter 1: Product introduction 1.1 1.2 1.3 Welcome! .....................................................
Contents Chapter 3: Powering up 3.1 3.2 Starting up for the first time ................................................ 3-1 Turning off the computer ..................................................... 3-2 3.2.1 Using the OS shut down function ........................... 3-2 3.2.2 Using the dual function power switch .................... 3-2 Chapter 4: BIOS setup 4.1 4.2 4.3 4.4 iv Managing and updating your BIOS ........................................ 4-1 4.1.1 Creating a bootable floppy disk ....
Contents 4.5 4.6 4.7 Power menu ........................................................................ 4-33 4.5.1 Suspend Mode ...................................................... 4-33 4.5.2 Repost Video on S3 Resume ................................ 4-34 4.5.3 ACPI 2.0 Support .................................................. 4-34 4.5.4 ACPI APIC Support ................................................ 4-34 4.5.5 APM Configuration ................................................ 4-34 4.5.
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This user guide contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports. • Chapter 2: Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components.
Conventions used in this guide To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual. D A N G E R / W A R N I N G : Information to prevent injury to yourself when trying to complete a task. C A U T I O N : Information to prevent damage to the components when trying to complete a task. I M P O R T A N T : Instructions that you MUST follow to complete a task. N O T E : Tips and additional information to help you complete a task.
P5WD2 Premium specifications summary CPU LGA775 socket for Intel® Pentium® 4/Celeron processor Compatible with Intel® PCG 05B/05A and 04B/04A processors Supports Intel® Enhanced Memory 64Technology (EM64T) Supports Enhanced Intel SpeedStep® Technology (EIST) Intel® Hyper-Threading Technology-ready Intel® Pentium® Processor Extreme Edition-ready Intel® Pentium® D Processor-ready Chipset Northbridge: Intel® 955X Memory Controller Hub (MCH) Southbridge: Intel® ICH7R Front Side Bus 1066/800/533 MHz Memory
P5WD2 Premium specifications summary High Definition Audio Realtek® ALC882D 8-channel High Definition Audio (HD Audio) CODEC featuring Dolby® Digital Live™ technology Supports Multi-streaming, Jack-sensing, and Jack-retasking functions Coaxial and optical S/PDIF out ports USB Supports up to 8 USB 2.
P5WD2 Premium specifications summary Rear panel 1 x Parallel port 1 x External Serial ATA port 1 x IEEE 1394a port 2 x LAN (RJ-45) ports 4 x USB 2.0 ports 1 x Optical S/PDIF Out port 1 x Coaxial S/PDIF Out port 1 x PS/2 keyboard port (purple) 1 x PS/2 mouse port (green) 8-channel audio ports Pow er we Requirement ATX power supply (with 24-pin and 2 x 4-pin 12 V plugs) ATX 12V 2.0 or later standard compliant Form Factor ATX form factor: 12 in x 9.6 in (30.5 cm x 24.
This chapter describes the motherboard features and the new technologies it supports.
Chapter summary 1 1.1 Welcome! .............................................................................. 1-1 1.2 Package contents ................................................................. 1-1 1.3 Special features ....................................................................
1.1 Welcome! Thank you for buying an ASUS® P 5 W D 2 P r e m i u m motherboard! The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your motherboard package for the following items.
1.3 Special features 1.3.1 Product highlights Latest processor technology The motherboard comes with a 775-pin surface mount Land Grid Array (LGA) socket designed for the Intel® Pentium® 4 processor in the 775-land package. The motherboard supports the Intel® Pentium® 4 processor and the Intel® Pentium® D processor with 1066/800/533 MHz Front Side Bus (FSB). The motherboard also supports the Intel® Hyper-Threading Technology and is fully compatible with Intel® 05B/05A and 04B/04A processors.
Enhanced Intel SpeedStep® Technology (EIST) The Enhanced Intel SpeedStep® Technology (EIST) intelligently manages the CPU resources by automatically adjusting the CPU voltage and core frequency depending on the CPU loading and system speed or power requirement. See page 4-27 and the Appendix for details.
8-channel high definition audio Onboard is the Realtek® ALC882D High Definition Audio 8-channel audio CODEC. This CODEC is fully-compliant with Intel® High Definition Audio standard (192 KHz, 24-bit audio). With the CODEC, 8-channel audio ports, and S/PDIF interfaces, you can connect your computer to home theater decoders to produce crystal-clear digital audio.
USB 2.0 technology The motherboard implements the Universal Serial Bus (USB) 2.0 specification, dramatically increasing the connection speed from the 12 Mbps bandwidth on USB 1.1 to a fast 480 Mbps on USB 2.0. USB 2.0 is backward compatible with USB 1.1. See pages 2-28 and 2-34 for details. Dual Gigabit LAN solution The motherboard comes with dual Gigabit LAN controllers to provide the total solution for your networking needs.
1.3.2 ASUS AI Life features Serial ATA II and SATA-On-The-Go The motherboard supports the Serial ATA 3 Gb/s technology through the Serial ATA interfaces and the Intel® 955X MCH chipset. The Serial ATA 3 Gb/ s specification provides twice the bandwidth of the current Serial ATA products with a host of new features, including Native Command Queuing (NCQ), Power Management (PM) Implementation Algorithm, and Hot Swap.
ASUS Stack Cool 2 ASUS Stack Cool 2 is a fan-less and zero-noise cooling solution that lowers the temperature of critical heat generating components by 20ºC. The motherboard uses a special design on the printed circuit board (PCB) to dissipate heat that critical components generate. See page 2-3 for details. 1.3.
Universal PCI Express slot The Universal PCI Express slot allows users to set up a dual graphics card platform on a single motherboard. The ASUS Smart Quick Switch detects PCI Express devices installed, and intelligently reroutes the PCI Express lanes to optimize bandwidth allocation. See page 2-22 for details. ASUS EZ Plug™ This patented ASUS technology is a 4-pin auxiliary +12V connector that is designed to maintain the voltage integrity of your system.
ASUS Q-Fan 2 technology The ASUS Q-Fan 2 technology smartly adjusts the fan speeds according to the system loading to ensure quiet, cool, and efficient operation. See pages 4-37 to 4-38 for details. ASUS Multi-language BIOS The multi-language BIOS allows you to select the language of your choice from the available options. The localized BIOS menus allow easier and faster configuration. See page 4-14 for details.
1-10 Chapter 1: Product introduction
This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
Chapter summary 2 2.1 Before you proceed .............................................................. 2-1 2.2 Motherboard overview .......................................................... 2-2 2.3 Central Processing Unit (CPU) .............................................. 2-7 2.4 System memory ................................................................. 2-14 2.5 Expansion slots ................................................................... 2-20 2.6 Jumper .........................
2.1 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity. • Hold components by the edges to avoid touching the ICs on them.
2.2 Motherboard overview Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components. 2.2.1 Placement direction When installing the motherboard, make sure that you place it into the chassis in the correct orientation.
2.2.3 ASUS Stack Cool 2 The motherboard comes with the ASUS Stack Cool 2 cooling solution that lowers the temperature of critical heat generating components by 20ºC. The motherboard uses a special design on the printed circuit board (PCB) to dissipate heat that critical components generate.
2.2.4 Motherboard layout 24.5cm (9.6in) PS/2KBMS T: Mouse B: Keyboard Super I/O CPU_FAN EATX12V PARALLEL PORT SPDIF_O IE1394a Intel® MCH 955X FLOPPY EZ_PLUG 30.5cm (12.
2.2.5 Layout contents Slots Page 1. DDR2 DIMM slots 2-14 2. PCI Express x16 slot 2-22 3. Universal PCI-E slot 2-22 4. PCI slots 2-25 5. PCI Express x1 slot 2-25 Jumper Page 1. 2-26 Clear RTC RAM (3-pin CLRTC) Rear panel connectors Page 1. PS/2 mouse port (green) 2-27 2. Parallel port 2-27 3. Center/Subwoofer port (yellow orange) 2-27 4. Side Speaker Out port (black) 2-27 5. Line In port (light blue) 2-27 6. Line Out port (lime) 2-27 7. LAN2 (RJ-45) port 2-27 8.
2-6 Internal connectors Page 1. Floppy disk drive connector (34-1 pin FLOPPY) 2-29 2. ITE IDE connectors (40-1 pin PRI_EIDE [red], SEC_EIDE [red] 2-29 3. ICH7R Primary IDE connector (40-1 pin PRI_IDE) 2-30 4. ICH7R Serial ATA connectors (7-pin SATA1 [red], SATA2 [red], SATA3 [black], SATA4 [black]) 2-31 5. Sil 3132 Serial ATA RAID connector (7-pin SATA_RAID2) 2-32 6. Optical drive audio connector (4-pin CD) 2-33 7. Front panel audio connector (10-1 pin AAFP) 2-33 8.
2.3 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA775 socket designed for the Intel® Pentium® 4/Intel® Pentium® D processor in the 775-land package. This motherboard supports the Intel® Pentium® Processor Extreme Edition, the latest CPU with embedded dual physical cores and Hyper-Threading technology, making four CPU threads possible. Refer to the table below for the operating system support status.
2.3.1 Installing the CPU To install a CPU: Locate the CPU socket on the motherboard. P5WD2 PREMIUM 1. ® P5WD2 PREMIUM CPU Socket 775 Before installing the CPU, make sure that the cam box is facing towards you and the load lever is on your left. 2. Press the load lever with your thumb (A), then move it to the left (B) until it is released from the retention tab. Retention tab A PnP cap Load lever B This side of the socket box should face you.
4. Lift the load plate with your thumb and forefinger to a 100º angle (A), then push the PnP cap from the load plate window to remove (B). B A Load plate 5. Position the CPU over the socket, making sure that the gold triangle is on the bottom-left corner of the socket. The socket alignment key should fit into the CPU notch. Alignment key Gold triangle mark The CPU fits in only one correct orientation.
2.3.2 Installing the CPU heatsink and fan The Intel® Pentium® 4 LGA775 processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. • When you buy a boxed Intel® Pentium® 4 processor, the package includes the CPU fan and heatsink assembly. If you buy a CPU separately, make sure that you use only Intel®-certified multi-directional heatsink and fan.
2. 3. Push down two fasteners at a time in a diagonal sequence to secure the heatsink and fan assembly in place. A B B A B A A B Connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN. GND CPU FAN PWR CPU FAN IN CPU FAN PWM P5WD2 PREMIUM CPU_FAN ® P5WD2 PREMIUM CPU fan connector Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector.
2.3.3 Uninstalling the CPU heatsink and fan To uninstall the CPU heatsink and fan: 1. Disconnect the CPU fan cable from the connector on the motherboard. 2. Rotate each fastener counterclockwise. 3. Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and fan assembly from the motherboard. B A A B 4. 2-12 A B B A Carefully remove the heatsink and fan assembly from the motherboard.
5. Rotate each fastener clockwise to ensure correct orientation when reinstalling. Narrow end of the groove The narrow end of the groove should point outward after resetting. (The photo shows the groove shaded for emphasis.) Refer to the documentation in the boxed or stand-alone CPU fan package for detailed information on CPU fan installation.
2.4 System memory 2.4.1 Overview The motherboard comes with four Double Data Rate 2 (DDR2) Dual Inline Memory Modules (DIMM) sockets. A DDR2 module has the same physical dimensions as a DDR DIMM but has a 240-pin footprint compared to the 184-pin DDR DIMM. DDR2 DIMMs are notched differently to prevent installation on a DDR DIMM socket.
Notes on memory limitations • Due to chipset limitation, this motherboard can only support up to 8 GB on the operating systems listed below. You may install a maximum of 2 GB DIMMs on each slot, but only DDR2-533 2 GB density modules are available for this configuration.
Qualified Vendors Lists DDR2-800 DDR2 Size Vendor Model Brand Infineon Side(s) C o m p o n e n t DS DIMM support A B C 512 MB Infineon HYS64T64520HU-2.
DDR2-533 DIMM support A B C DDR2 Size Vendor 512 MB SAMSUNG M378T6553BG0-CD5 N/A SS K4T51083QB-GCD5 • • • 256 MB SAMSUNG M378T3253FG0-CD5 N/A SS K4T56083QF-GCD5 • • • 512 MB SAMSUNG M378T6453FG0-CD5 N/A DS K4T56083QF-GCD5 • • • 1024 MB SAMSUNG M391T2953BG0-CD5 N/A DS K4T51083QB-GCD5(ECC) • • • 512 MB SAMSUNG M391T6453FG0-CD5 N/A DS K4T56083QF-GCD5(ECC) • • • 512 MB Infineon HYS64T64000GU-3.
DDR2-533 DDR2 Size Vendor Model Brand Side(s) C o m p o n e n t DIMM support A B C 512 MB NANYA NT512T64U88A0F-37B NANYA SS NT5TU64M8AF-37B • • • 1024 MB NANYA NT1GT64U8HA0F-37B NANYA DS NT5TU64M8AF-37B • • • 512 MB NANYA NT512T72U89A0F-37B NANYA SS NT5TU64M8AF-37B(ECC)• • • 256 MB elixir M2U25664TUH4A0F-37B - SS N2TU51216AF-37B • • • 512 MB elixir M2U51264TU88A0F-37B - SS N2TU51280AF-37B • • • 256 MB crucial BL3264AA53V.
2.4.3 Installing a DIMM Unplug the power supply before adding or removing DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components. 2 To install a DIMM: 1. Unlock a DIMM socket by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. 3.
2.5 Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. 2.5.1 Installing an expansion card To install an expansion card: 1.
2.5.
2.5.4 PCI Express x16 slots This motherboard has two PCI Express x16 slots that support PCI Express x16 graphic cards complying with the PCI Express specifications. With two graphics cards installed, the motherboard can enable quad-display. Primary PCI Express x 16 slot for discrete graphics card (blue) Universal PCI-E slot [max. x4 mode] (black) We recommend that you install a VGA card on the primary (blue) PCI Express slot, and install any other PCI Express device on the Universal PCI-E slot (black).
Tested VGA cards to run at x2/x4 mode PCIe x16 VGA Card PCI _ 2X PCI _ 4X Abit RX300SE-PCIE Rev. V1.0 (BIOS: V008.015) Pass Pass ASUS EN5750/128 Rev. 1.01 (BIOS: V04.32.20.38.00) Fail Pass ASUS EN6600GT Rev. V1.00 (BIOS: V5.43.02.16.AS27) Pass Pass ELSA Gladiac PCX 935 Rev. W01-46W53 (BIOS: V4.35.20.45.E0) Pass Pass Gigabyte GV-NX68T256D-B Rev: B (BIOS: V5.40.02.36.09) Pass Pass Abit RX600XT-PCIE Rev. B (BIOS: V008.015) Pass Pass ASUS EAX300SE Rev: V1.00 (BIOS: V5b60.8.15.117.
Tested VGA cards to run at x2/x4 mode PCIe x16 VGA Card PCI _ 2X PCI _ 4X ASUS EAX800XT Rev. V1.00 (BIOS: V5D57.9.4.1.8.AS) Pass Pass ASUS EN6200TC128/T/16M Rev V1.01 (BIOS: V5.44.02.11) Pass Pass ASUS EN6800GT Rev. V1.02 (BIOS: V5.40.02.26.AS05) Pass Pass Gigabyte GV-NX57128D Rev. V1.0 (BIOS: V4.36.20.38.00) Pass Pass Leadtek WinFast PX6600 TDH Rev. A1 (BIOS: V5.43.02.16) Pass Pass MSI RX700PRO-TD128E Rev.V2.00 (BIOS: V009.004.001.032) Pass Pass Albatron PC6600GT (BIOS: V5.43.02.
2.5.5 PCI slots The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The figure shows a LAN card installed on a PCI slot. 2.5.6 PCI Express x1 slot This motherboard supports PCI Express x1 network cards, SCSI cards and other cards that comply with the PCI Express specifications. The following figure shows a network card installed on the PCI Express x1 slot.
2.6 1. Jumper Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM: 1. Turn OFF the computer and unplug the power cord. 2. Remove the onboard battery. 3. Move the jumper cap from pins 1-2 (default) to pins 2-3.
2.7 Connectors 2.7.1 Rear panel connectors 1 2 17 1. 2. 16 15 34 14 56 13 12 7 8 11 10 9 P S / 2 m o u s e p o r t ( g r e e n ) . This port is for a PS/2 mouse. P a r a l l e l p o r t . This 25-pin port connects a parallel printer, a scanner, or other devices. S i d e S p e a k e r O u t p o r t ( b l a c k ) . This port connects the side speakers in an 8-channel audio configuration. 3. 4. C e n t e r / S u b w o o f e r p o r t ( y e l l o w o r a n g e ) .
9. I E E E 1 3 9 4 a p o r t . This 6-pin IEEE 1394a port provides high-speed connectivity for audio/video devices, storage peripherals, PCs, or portable devices. 1 0 . U S B 2 . 0 p o r t s 3 a n d 4 . These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. 1 1 . U S B 2 . 0 p o r t s 1 a n d 2 . These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. 1 2 . M i c r o p h o n e p o r t ( p i n k ) .
2.7.2 1. Internal connectors Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. P5WD2 PREMIUM Pin 5 on the connector is removed to prevent incorrect cable connection when using a FDD cable with a covered Pin 5. FLOPPY NOTE: Orient the red markings on the floppy ribbon cable to PIN 1.
3. ICH7R Primary IDE connector (40-1 pin PRI_IDE) This connector is for an Ultra DMA 100/66 signal cable. The Ultra DMA 100/66 signal cable has three connectors: a blue connector for the primary IDE connector on the motherboard, a black connector for an Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 100/66 IDE master device (hard disk drive).
4. ICH7R Serial ATA connectors (7-pin SATA1 [red], SATA2 [red], SATA3 [black], SATA4 [black]) These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives. If you installed Serial ATA hard disk drives, you can create a RAID 0, RAID 1, RAID 5, RAID 10 configuration with the Intel® Matrix Storage Technology through the onboard Intel® ICH7R RAID controller. Refer to Chapter 5 for details on how to set up Serial ATA RAID configurations. For RAID 5, use at least three hard disk drives.
Serial ATA hard disk drive connection 5. Connector Color Setting Use SATA1/SATA2 Red Master Boot disk SATA3/SATA4 Black Slave Data disk S i l i c o n I m a g e® S e r i a l A T A R A I D c o n n e c t o r (7-pin SATA_RAID2) This connector is for a Serial ATA signal cable. This connector supports a Serial ATA hard disk drive that you can configure for RAID through the onboard Serial ATA RAID controller. Refer to Chapter 5 for details on how to set up Serial ATA RAID configurations.
6. Optical drive audio connector (4-pin CD) Right Audio Channel Ground Ground Left Audio Channel P5WD2 PREMIUM This connector is for the 4-pin audio cable that connects to the audio connector at the back of the optical drive.
8. USB connectors (10-1 pin USB56, USB78) P5WD2 PREMIUM These connectors are for USB 2.0 ports. Connect the USB/GAME module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed. USB+5V USB_P8USB_P8+ GND NC USB+5V USB_P6USB_P6+ GND NC ® USB78 P5WD2 PREMIUM USB 2.
1 0 . GAME/MIDI port connector (16-1 pin GAME) +5V J1B2 J1CY GND GND J1CX J1B1 +5V P5WD2 PREMIUM This connector is for a GAME/MIDI port. Connect the USB/GAME module cable to this connector, then install the module to a slot opening at the back of the system chassis. The GAME/MIDI port connects a joystick or game pad for playing games, and MIDI devices for playing or editing audio files. ® MIDI_IN J2B2 J2CY MIDI_OUT J2CX J2B1 +5V GAME P5WD2 PREMIUM Game connector 1 1 .
1 2 . CPU, Chassis, and Power Fan connectors (4-pin CPU_FAN, 3-pin PWR_FAN, 3-pin CHA_FAN1, 3-pin CHA_FAN2) The fan connectors support cooling fans of 350 mA ~ 2000 mA (24 W max.) or a total of 1 A ~ 3.48 A (41.76 W max.) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors.
1 3 . Serial port connector (10-1 pin COM1) P5WD2 PREMIUM This connector is for a serial (COM) port. Connect the serial port module cable to this connector, then install the module to a slot opening at the back of the system chassis. PIN 1 COM1 ® P5WD2 PREMIUM COM port connector 1 4 .
• You may use a 4-pin ATX12V power plug for this connector. • Make sure to remove the cap on the connector before connecting an 8-pin EPS +12V power plug. • Use only either a 4-pin ATX12V or an 8-pin EPS +12V power plug. Connecting other power plug types may cause serious damage to the system.
Power Supply Unit Reference Vendors List Vendor Model ASUS A-40GA 400 Delta GPS-400AA-100 A 400 Hipro HP-E4008FWR 400 Delta GPS-450AA-100 A 450 ASUS A-45GA 450 AcBel API4PC04 450 Seventeam ST-460EAD-05F 460 AcBel API4PC23 500 AcBel API4PC24 550 ASUS P5WD2 Premium Max.
1 5 . System panel connector (20-pin PANEL) This connector supports several chassis-mounted functions. +5V Ground Ground Speaker PLED- PLED+ IDE_LED Reset Ground PWR Ground ® SPEAKER PANEL IDE_LED+ IDE_LED- P5WD2 PREMIUM PLED RESET PWRSW * Requires an ATX power supply. P5WD2 PREMIUM System panel connector The sytem panel connector is color-coded for easy connection. Refer to the connector description below for details.
This chapter describes the power up sequence, the vocal POST messages, and ways of shutting down the system.
Chapter summary 3 3.1 Starting up for the first time ................................................ 3-1 3.2 Turning off the computer .....................................................
3.1 Starting up for the first time 1. After making all the connections, replace the system case cover. 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: a. Monitor b. External SCSI devices (starting with the last device on the chain) c. 6.
3.2 Turning off the computer 3.2.1 Using the OS shut down function If you are using Windows® 2000: 2. Click the S t a r t button then click S h u t D o w n . . . Make sure that the S h u t D o w n option button is selected, then click the O K button to shut down the computer. 3. The power supply should turn off after Windows® shuts down. 1. If you are using Windows® XP or later version: 2. Click the S t a r t button then select T u r n O f f C o m p u t e r .
This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
Chapter summary 4 4.1 Managing and updating your BIOS ........................................ 4-1 4.2 BIOS setup program ........................................................... 4-11 4.3 Main menu .......................................................................... 4-14 4.4 Advanced menu .................................................................. 4-19 4.5 Power menu ........................................................................ 4-33 4.6 Boot menu .....................
4.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. 2. 3. 4. A S U S A F U D O S (Updates the BIOS in DOS mode using a bootable floppy disk.) A S U S C r a s h F r e e B I O S 2 (Updates the BIOS using a bootable floppy disk or the motherboard support CD when the BIOS file fails or gets corrupted.) A S U S E Z F l a s h (Updates the BIOS in DOS mode using a floppy disk or the motherboard support CD.
Windows® 2000 environment To create a set of boot disks for Windows® 2000: a. Insert a formatted, high density 1.44 MB floppy disk into the drive. b. Insert the Windows® 2000 CD to the optical drive. c. Click S t a r tt, then select R u n n. d. In the O p e n field, type D:\bootdisk\makeboot a: assuming that D is your optical drive letter. e. Press , then follow screen instructions to continue. 2. Copy the original or the latest motherboard BIOS file to the bootable floppy disk. 4.1.
3. Press . The utility copies the current BIOS file to the floppy disk. A:\>afudos /oOLDBIOS1.rom AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB)) Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading flash ..... done Write to file...... ok A:\> The utility returns to the DOS prompt after copying the current BIOS file. Updating the BIOS file To update the BIOS file using the AFUDOS utility: 1. Visit the ASUS website (www.asus.
4. The utility verifies the file and starts updating the BIOS. A:\>afudos /iP5WD2P.rom AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB)) Copyright (C) 2002 American Megatrends, Inc. All rights reserved. WARNING!! Do not turn off power during flash BIOS Reading file ....... done Reading flash ...... done Advance Check ...... Erasing flash ...... done Writing flash ...... 0x0008CC00 (9%) Do not shut down or reset the system while updating the BIOS to prevent system boot failure! 5.
4.1.3 ASUS CrashFree BIOS 2 utility The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can update a corrupted BIOS file using the motherboard support CD or the floppy disk that contains the updated BIOS file. • Prepare the motherboard support CD or the floppy disk containing the updated motherboard BIOS before using this utility.
Recovering the BIOS from the support CD To recover the BIOS from the support CD: 1. Remove any floppy disk from the floppy disk drive, then turn on the system. 2. Insert the support CD to the optical drive. 3. The utility displays the following message and automatically checks the floppy disk for the original or updated BIOS file. Bad BIOS checksum. Starting BIOS recovery... Checking for floppy...
4.1.4 ASUS EZ Flash utility The ASUS EZ Flash feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS-based utility. The EZ Flash utility is built-in the BIOS chip so it is accessible by pressing + during the Power-On Self Tests (POST). To update the BIOS using EZ Flash: 1. Visit the ASUS website (www.asus.com) to download the latest BIOS file for the motherboard and rename the same to P 5 W D 2 P . R O M M. 2.
4.1.5 ASUS Update utility The ASUS Update is a utility that allows you to manage, save, and update the motherboard BIOS in Windows® environment. The ASUS Update utility allows you to: • Save the current BIOS file • Download the latest BIOS file from the Internet • Update the BIOS from an updated BIOS file • Update the BIOS directly from the Internet, and • View the BIOS version information. This utility is available in the support CD that comes with the motherboard package.
Updating the BIOS through the Internet To update the BIOS through the Internet: 1. Launch the ASUS Update utility from the Windows® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate e. The ASUS Update main window appears. 2. Select U p d a t e B I O S f r o m t h e I n t e r n e t option from the drop-down menu, then click N e x tt. ASUS P5WD2 Premium 3. Select the ASUS FTP site nearest you to avoid network traffic, or click A u t o S e l e c tt. Click N e x tt.
4. From the FTP site, select the BIOS version that you wish to download. Click Next. 5. Follow the screen instructions to complete the update process. The ASUS Update utility is capable of updating itself through the Internet. Always update the utility to avail all its features. Updating the BIOS through a BIOS file To update the BIOS through a BIOS file: 1. 2. 3. 4.
4.2 BIOS setup program This motherboard supports a programmable firmware chip that you can update using the provided utility described in section “4.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup.” This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you can change the configuration of your computer in the future.
4.2.1 BIOS menu screen Menu items Menu bar System Time System Date Legacy Diskette A Language Primary IDE Master Primary IDE Slave Third IDE Master Third IDE Slave Fourth IDE Master Fourth IDE Slave IDE Configuration Configuration fields [11:51:19] [Sat 03/26/2005] [1.44M, 3.5 in] [English] [ST320413A] [ASUS CD-S520/A] [Not Detected] [Not Detected] [Not Detected] [Not Detected] General help Use [ENTER], [TAB], or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system.
4.2.4 Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting M a i n shows the Main menu items. The other items (Advanced, Power, Boot, and Exit) on the menu bar have their respective menu items. 4.2.5 System Time System Date Legacy Diskette A Language [11:51:19] [Sat 03/26/2005] [1.44M, 3.
4.3 Main menu When you enter the BIOS Setup program, the M a i n menu screen appears, giving you an overview of the basic system information. Refer to section “4.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them. System Time System Date Legacy Diskette A Language Primary IDE Master Primary IDE Slave Third IDE Master Third IDE Slave Fourth IDE Master Fourth IDE Slave IDE Configuration Use [ENTER], [TAB], or [SHIFT-TAB] to select a field.
4.3.5 Primary, Third, and Fourth IDE Master/Slave The BIOS automatically detects the connected IDE devices. There is a separate sub-menu for each IDE device. Select a device item, then press to display the IDE device information. Primary IDE Master Device : Hard Disk Vendor : ST320413A Size : 20.
PIO Mode [Auto] Selects the PIO mode. Configuration options: [Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] Selects the DMA mode. Configuration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5] SMART Monitoring [Auto] Sets the Smart Monitoring, Analysis, and Reporting Technology. Configuration options: [Auto] [Disabled] [Enabled] 32Bit Data Transfer [Disabled] Enables or disables 32-bit data transfer.
If you want the Serial ATA hard disk drives to use the Advanced Host Controller Interface (AHCI), set this item to [AHCI]. For details on AHCI, go to: www.intel.com/support/chipsets/imst/sb/CS-012304.htm www.intel.com/support/chipsets/imst/sb/CS-012305.htm The SATA controller is set to Native mode when this item is set to [RAID] or [AHCI] Onboard IDE Operate Mode [Enhanced Mode] Allows selection of the IDE operation mode depending on the installed operating system (OS).
ALPE and ASP [Disabled] Allows you to enable or disable the Agressive Link Power Management (ALPE) and Aggressive Slumber/Partial (ASP) management features. Configuration options: [Disabled] [Enabled] The A L P E a n d A S P and its sub-menu item appear only when the C o n f i g u r e S A T A A s item is set to [AHCI]. IDE Detect Time Out [35] Selects the time out value for detecting ATA/ATAPI devices. Configuration options: [0] [5] [10] [15] [20] [25] [30] [35] 4.3.
4.4 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Take caution when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. Adjust system frequency/voltage. JumperFree Configuration LAN Cable Status USB Configuration CPU Configuration Chipset Onboard Devices Configuration PCIPnP 4.4.
The following item appears only when you install a CPU that supports the lock free feature. Only some latest CPUs support this feature CPU Lock Free [Auto] This feature allows you to adjust the CPU multiplier to 14x. Setting this item to [Auto] allows the motherboard to automatically reduce the CPU multiplier value for more flexibility when increasing external FSB.
Performance Mode [Auto] Allows enhanced system performance. Setting to [Turbo] may cause the system to become unstable. If this happens, revert to the default setting [Auto]. Configuration options: [Auto] [Standard] [Turbo] PCI Express Frequency [Auto] Allows you to set the PCI Express frequency. This item is set to [Auto] by default. Configuration options: [Auto] [90] ~ [150] PCI Clock Synchronization Mode [Auto] Allows you to synchronize the PCI frequency with the PCI Express or CPU frequency.
MCH Chipset Voltage [Auto] Allows you to select the chipset voltage of the memory controller hub (MCH). Configuration options: [Auto] [1.500V] [1.550V] [1.600V] [1.650V] Setting a high MCH chipset voltage may damage the chipset! ICH Chipset Voltage [Auto] Allows you to select the chipset voltage of the I/O controller hub (ICH). Configuration options: [Auto] [1.05V] [1.
Target Frequency [Overclock XX%] Allows you to set the maximum overclock percentage for the selected NOS Mode. Configuration options: [Overclock 3%] [Overclock 5%] [Overclock 7%] [Overclock 10%] [Overclock 15%] [Overclock 20%] [Overclock 30%] Selecting a very high frequency may cause the system to become unstable. If this happens, revert to the default setting. 4.4.2 LAN Cable Status This menu displays the status of the Local Area Network (LAN) cable connected to the LAN (RJ-45) port.
4.4.3 USB Configuration The items in this menu allows you to change the USB-related features. Select an item then press to display the configuration options. Enables USB host controllers. USB Configuration Module Version - 2.24.0-F.4 USB Devices Enabled: None USB Function Legacy USB Support USB 2.0 Controller USB 2.
BIOS EHCI Hand-off [Disabled] Allows you to enable support for operating systems without an EHCI hand-off feature. Configuration options: [Enabled] [Disabled] USB Mass Storage Device Configuration USB Mass Storage Reset Delay [20 ] Sets the USB mass storage reset delay time in seconds.
4.4.4 CPU Configuration The items in this menu show the CPU-related information that the BIOS automatically detects. Configure Advanced CPU settings Manufacturer: Intel Brand String: Genuine Intel(R) CPU 3.20GHz Frequency : 3200 MHz FSB Speed : 800 MHz Cache L1 Cache L2 Cache L3 : 16 KB : 1024 KB : 0 KB Sets the ratio between CPU Core Clock and the FSB Frequency. NOTE: If an invalid ratio is set in CMOS then actual and setpoint values may differ.
Execute Disable Function [Disabled] Allows you to enable or disable the No-Execution Page Protection Technology. Setting this item to [Enabled] forces the XD feature flag to always return to zero (0). Configuration options: [Disabled] [Enabled] Enhanced C1 Control [Auto] When set to [Auto], the BIOS automatically checks the CPU’s capability to enable the C1E support. In C1E mode, the CPU power consumption is lower when idle.
4.4.5 Chipset The Chipset menu allows you to change the advanced chipset settings. Select an item then press to display the sub-menu.
Hyper Path 3 [Auto] Allows you to enable or disable the ASUS Hyper Path 3 feature. Configuration options: [Disabled] [Enabled] [Auto] Booting Graphic Adapter Priority [PCI Express/PCI] Allows selection of the graphics controller to use as primary boot device. Configuration options: [PCI Express/PCI] [PCI/PCI Express] PEG Buffer Length [Auto] Sets the length of the PCI Express graphics card buffer.
4.4.
LAN Option ROM [Disabled] This item allows you to enable or disable the option ROM in the onboard LAN controller. This item appears only when the O n b o a r d P C I L A N item is set to Enabled. Configuration options: [Disabled] [Enabled] Silicon 3132 Controller [SATA2 Mode] Allows you to set the mode at which the onboard Silicon Image 3132 Serial ATA controller will operate. Set this item to [SATA2 Mode] to enable hot-plug function for the external device.
Onboard Game/MIDI Port [Disabled] Allows you to select the Game Port address or to disable the port. Configuration options: [Disabled] [200/300] [200/330] [208/300] [208/330] 4.4.7 PCI PnP The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices. Take caution when changing the settings of the PCI PnP menu items.
Allocate IRQ to PCI VGA [Yes] When set to [Yes], BIOS assigns an IRQ to PCI VGA card if the card requests for an IRQ. When set to [No], BIOS does not assign an IRQ to the PCI VGA card even if requested. Configuration options: [No] [Yes] Palette Snooping [Disabled] When set to [Enabled], the palette snooping feature informs the PCI devices that an ISA graphics device is installed in the system so that the latter can function correctly.
4.5.2 Repost Video on S3 Resume [No] Determines whether to invoke VGA BIOS POST on S3/STR resume. Configuration options: [No] [Yes] 4.5.3 ACPI 2.0 Support [No] Allows you to add more tables for Advanced Configuration and Power Interface (ACPI) 2.0 specifications. Configuration options: [No] [Yes] 4.5.4 ACPI APIC Support [Enabled] Allows you to enable or disable the Advanced Configuration and Power Interface (ACPI) support in the Advanced Programmable Interrupt Controller (APIC).
Power On By RTC Alarm [Disabled] Allows you to enable or disable RTC to generate a wake event. Configuration options: [Disabled] [Enabled] The succeeding items appear when the P o w e r O n B y R T C A l a r m item is set to Enabled. RTC Alarm Date To set the alarm date, highlight this item and press the <+> or <-> key to make the selection. Configuration options: [Everyday] [1] [2] [3]... ~ [31] RTC Alarm Hour To set the alarm hour, highlight this item and press the <+> or <-> key to make the selection.
Power On By PS/2 Keyboard [Disabled] Allows you to use specific keys on the keyboard to turn on the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Space Bar] [Ctrl-Esc] [Power Key] Power On By PS/2 Mouse [Disabled] When set to [Enabled], this parameter allows you to use the PS/2 mouse to turn on the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead.
4.5.6 Hardware Monitor Hardware Monitor CPU Temperature MB Temperature [32.5ºC/90.5ºF] [36.0ºC/96.5ºF] CPU Fan Speed (RPM) ASUS Q-Fan Control Chassis Fan1 Speed (RPM) Chassis Fan2 Speed (RPM) Chassis Q-Fan Control Power Fan Speed (RPM) [3813 RPM] [Disabled] [N/A] [N/A] [Disabled] [N/A] VCORE Voltage 3.3V Voltage 5V Voltage 12V Voltage [ 1.320V] [ 3.345V] [ 5.094V] [11.
CPU Fan Profile Mode [Optimal] Allows you to set the appropriate CPU fan performance. When set to [Optimal], the CPU fan automatically adjusts depending on the CPU temperature. Set this item to [Silent] to minimize fan speed for quiet CPU fan operation, or [Performance] to achieve maximum CPU fan speed.
Power Fan Speed (RPM) [xxxxRPM] or [N/A] The onboard hardware monitor automatically detects and displays the power fan speed in rotations per minute (RPM). If the fan is not connected to the power fan connector, the specific field shows N/A. VCORE Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators.
4.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press to display the sub-menu. Specifies the Boot Device Priority sequence. Boot Settings Boot Device Priority Boot Settings Configuration Security 4.6.1 A virtual floppy disk drive (Floppy Drive B:) may appear when you set the CD-ROM drive as the first boot device.
4.6.2 Boot Settings Configuration Boot Settings Configuration Quick Boot Full Screen Logo AddOn ROM Display Mode Bootup Num-Lock PS/2 Mouse Support Wait For ‘F1’ If Error Hit ‘DEL’ Message Display Interrupt 19 Capture [Enabled] [Enabled] [Force BIOS] [On] [Auto] [Enabled] [Enabled] [Disabled] Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system.
Interrupt 19 Capture [Disabled] When set to [Enabled], this function allows the option ROMs to trap Interrupt 19. Configuration options: [Disabled] [Enabled] 4.6.3 Security The Security menu items allow you to change the system security settings. Select an item then press to display the configuration options. Security Settings Supervisor Password User Password : Not Installed : Not Installed to change password. again to disabled password.
After you have set a supervisor password, the other items appear to allow you to change other security settings. Security Settings Supervisor Password User Password : Not Installed : Not Installed Change Supervisor Password User Access Level Change User Password Clear User Password Password Check [Full Access] [Setup] User Access Level [Full Access] This item allows you to select the access restriction to the Setup items.
Clear User Password Select this item to clear the user password. Password Check [Setup] When set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system.
4.7 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items. Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Load Setup Defaults Pressing does not immediately exit this menu. Select one of the options from this menu or from the legend bar to exit.
Load Setup Defaults Allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press , a confirmation window appears. Select O K to load default values. Select E x i t & S a v e C h a n g e s or make other changes before saving the values to the non-volatile RAM.
This chapter describes the contents of the support CD that comes with the motherboard package.
Chapter summary 5 5.1 Installing an operating system ............................................. 5-1 5.2 Support CD information ........................................................ 5-1 5.3 Software information ........................................................... 5-8 5.4 RAID configurations ............................................................ 5-17 5.5 Creating a RAID driver disk .................................................
5.1 Installing an operating system This motherboard supports Windows® 2000/2003 Server/XP operating systems (OS). Always install the latest OS version and corresponding updates to maximize the features of your hardware. 5.2 • Motherboard settings and hardware options vary. Use the setup procedures presented in this chapter for reference only. Refer to your OS documentation for detailed information.
5.2.2 Drivers menu The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. The screen display and driver options vary under different operating system versions. QFE Update Installs the Quick Fix Engineering (QFE) driver updates. Intel Chipset Inf Update Program Installs the Intel® Chipset INF Update Program. This driver enables Plug-n-Play INF support for the Intel® chipset components on the motherboard.
ITE8211 IDE Driver Installs the ITE8211 IDE drivers. Silicon Image SATA Driver Installs the Silicon Image Sil3112 SATA drivers. USB 2.0 Driver Installs the USB 2.0 driver. 5.2.3 Utilities menu The U t i l i t i e s menu displays the software applications and utilities that the motherboard supports. Click on an item to install. ASUS PC Probe II This smart utility monitors the fan speed, CPU temperature, and system voltages, and alerts you of any detected problems.
ADOBE Acrobat Reader The Adobe Acrobat® Reader V5.0 is for opening, viewing, and printing documents in Portable Document Format (PDF). Microsoft DirectX 9.0c The Microsoft DirectX® 9.0c is a multimedia technology that enhances computer graphics and sounds. DirectX® improves the multimedia features of your computer so you can enjoy watching TV and movies, capturing videos, or playing games in your computer.
Make ITE8211 32/64bit IDE Driver Disk Allows you to create an ITE8211 IDE driver disk. Make Silicon Image 32bit RAID Driver Disk Make Silicon Image 32bit SATA Driver Disk Allows you to create a Silicon Image® RAID/Serial ATA driver disk for a 32-bit system. Make Silicon Image 64bit RAID Driver Disk Make Silicon Image 64bit SATA Driver Disk Allows you to create a Silicon Image® RAID/Serial ATA driver disk for a 64-bit system. 5.2.
5.2.6 Contact information Click the C o n t a c t tab to display the ASUS contact information. You can also find this information on the inside front cover of this user guide. 5.2.7 Other information The icons on the top right corner of the screen provide additional information on the motherboard and the contents of the support CD. Click an icon to display the specified information. Motherboard Info Displays the general specifications of the motherboard.
Browse this CD Displays the contents of the support CD in graphical format. Technical Support Form Displays the ASUS Technical Support Request Form that you have to fill out when requesting technical support. Filelist Displays the contents of the support CD in text format.
5.3 Software information Most of the applications in the support CD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software application for more information. 5.3.1 ASUS MyLogo2™ The ASUS MyLogo2™ utility lets you customize the boot logo. The boot logo is the image that appears on screen during the Power-On-Self-Tests (POST).
7. When the logo images appear on the right window pane, select an image to enlarge by clicking on it. 8. Adjust the boot image to your desired size by selecting a value on the R a t i o box. 9. When the screen returns to the ASUS Update utility, flash the original BIOS to load the new boot logo. 10. After flashing the BIOS, restart the computer to display the new boot logo during POST.
5.3.2 AI NET2 The AI NET2 features the Marvell® Virtual Cable Tester™ (VCT). VCT is a cable diagnostic utility that reports LAN cable faults and shorts using the Time Domain Reflectometry (TDR) technology. The VCT detects and reports open and shorted cables, impedance mismatches, pair swaps, pair polarity problems, and pair skew problems of up to 64 ns at one meter accuracy. The VCT feature reduces networking and support costs through a highly manageable and controlled network system.
5.3.3 Audio configurations The Realtek® ALC882D audio CODEC provides 8-channel audio capability to deliver the ultimate audio experience on your computer. The software provides Jack-Sensing function, S/PDIF Out support, and interrupt capability. The ALC882D also includes the Realtek® proprietary UAJ® (Universal Audio Jack) technology for all audio ports, eliminating cable connection errors and giving users plug and play convenience.
Information Click the information button ( ) to display information about the audio driver version, DirectX version, audio controller, audio codec, and language setting. Tools Click the tool button ( applications. ) to display tools for supported Dolby® Dolby® feature launch buttons Click the button of the feature you want to launch. This motherboard only supports Dolby Digital Live. Minimize Click the minimize button ( ) to minimize the window.
Sound Effect The Realtek® ALC882D Audio CODEC allows you to set your listening environment, adjust the equalizer, set the karaoke, or select pre-programmed equalizer settings for your listening pleasure. To set the sound effect options: 1. From the Realtek HD Audio Manager, click the S o u n d E f f e c t tab. 2. Click the shortcut buttons or the drop-down menus for options on changing the acoustic environment or adjust the equalizer to your desired settings. 3.
Bass Management setting Click this tab to manage your bass settings. To set the bass management options: 1. From the Realtek HD Audio Manager, click the B a s s M a n a g e m e n t s e t t i n g tab. 2. Click to display the distance in meters, or to display the distance in feet. 3. Adjust the values to your desired settings by entering a numeric value in the boxes, or clicking the up/down arrow. 4. Click 5. Click to test your settings. to effect the Bass Management settings and exit.
Microphone The Microphone option allows you configure your input/output settings and to check if your audio devices are connected properly. To set the Microphone options: 1. From the Realtek HD Audio Manager, click the M i c r o p h o n e tab. 2. Click the N o i s e S u p p r e s s i o n option button to reduce the static background noise when recording. Click the A c o u s t i c E c h o C a n c e l l a t i o n option button to reduce the echo from the front speakers when recording. 3. 4.
Using Dolby® Digital Live Live™ The Dolby® Digital Live™ technology encodes your computer’s digital audio contents to real-time Dolby® Digital streams. Using the CODEC and the Sony/Philips Digital Interface (S/PDIF) ports on the motherboard, you can send the encoded Dolby® Digital streams to an AC-3 decoder for playback on a multi-channel speaker system. Refer to the following illustrations when converting sounds to Dolby® Digital streams.
5.4 RAID configurations The motherboard comes with the Silicon Image® 3132 and the Intel® ICH7R Southbridge RAID controllers that allow you to configure IDE and Serial ATA hard disk drives as RAID sets. The motherboard supports the following RAID configurations. R A I D 0 (Data striping) optimizes two identical hard disk drives to read and write data in parallel, interleaved stacks.
5.4.1 Installing Serial ATA hard disks The motherboard supports Serial ATA hard disk drives. For optimal performance, install identical drives of the same model and capacity when creating a disk array. To install the SATA hard disks for a RAID configuration: 1. Install the SATA hard disks into the drive bays. 2. Connect the SATA signal cables. 3. Connect a SATA power cable to the power connector on each drive. 5.4.
Intel® Matrix Storage Manager Option ROM Utility The Intel® Matrix Storage Manager Option ROM utility allows you to create RAID 0, RAID 1, RAID 10 (RAID 0+1), and RAID 5 set(s) from Serial ATA hard disk drives that are connected to the Serial ATA connectors supported by the Southbridge. To enter the Intel® Application Accelerator RAID Option ROM utility: 1. Install all the Serial ATA hard disk drives. 2. Turn on the system. 3. During POST, press to display the utility main menu.
Creating a RAID 0 set (striped) To create a RAID 0 set: 1. From the utility main menu, select 1 . C r e a t e R A I D V o l u m e e, then press . This screen appears. Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH7R wRAID5 Copyright(C) 2003-05 Intel Corporation. All Rights Reserved. [ CREATE ARRAY MENU ] Name: RAID Level: Disks: Strip Size: Capacity: Volume0 RAID0(Stripe) Select Disks 128KB 0.
6. Use the up/down arrow key to select the stripe size for the RAID 0 array, then press . The available stripe size values range from 4 KB to 128 KB. The default stripe size is 128 KB. T I P : We recommend a lower stripe size for server systems, and a higher stripe size for multimedia computer systems used mainly for audio and video editing. 7. 8. Key in the RAID volume capacity that you want, then press . The default value indicates the maximum allowed capacity.
Creating a RAID 1 set (mirrored) To create a RAID 1 set: 1. From the utility main menu, select 1 . C r e a t e R A I D V o l u m e e, then press . This screen appears. Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH7R wRAID5 Copyright(C) 2003-05 Intel Corporation. All Rights Reserved. [ CREATE ARRAY MENU ] Name: RAID Level: Disks: Strip Size: Capacity: Volume1 RAID1(Mirror) Select Disks N/A XX.
Creating a RAID 10 set (RAID 0+1) To create a RAID 10 set: 1. From the utility main menu, select 1 . C r e a t e R A I D V o l u m e e, then press . This screen appears. Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH7R wRAID5 Copyright(C) 2003-05 Intel Corporation. All Rights Reserved. [ CREATE ARRAY MENU ] Name: RAID Level: Disks: Strip Size: Capacity: Volume10 RAID10(RAID0+1) Select Disks 128KB XXX.
6. Press when the C r e a t e V o l u m e item is highlighted. This warning message appears. WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST. Are you sure you want to create this volume? (Y/N): 7. Press to create the RAID volume and return to the main menu or to go back to the Create Volume menu. Creating a RAID 5 set (parity) To create a RAID 5 set: 1. From the utility main menu, select 1 . C r e a t e R A I D V o l u m e e, then press . This screen appears.
4. The Disks item is highlighted, press to select the hard disk drives to configure as RAID. The following pop-up screen appears. [ SELECT DISKS ] Port 0 1 2 3 Drive Model XXXXXXXXXXXX XXXXXXXXXXXX XXXXXXXXXXXX XXXXXXXXXXXX Serial # XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX Size XX.XGB XX.XGB XX.XGB XX.XGB Status Non-RAID Non-RAID Non-RAID Non-RAID Disk Disk Disk Disk Select 2 to 4 disks to use in creating the volume. [↑↓ ↑↓]-Previous/Next ↑↓ 5. 6.
Deleting a RAID set Take caution when deleting a RAID set. You will lose all data on the hard disk drives when you delete a RAID set. To delete a RAID set: 1. From the utility main menu, select 2 . D e l e t e R A I D V o l u m e e, then press to display this screen. Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH7R wRAID5 Copyright(C) 2003-05 Intel Corporation. All Rights Reserved. [ DELETE VOLUME MENU ] Name Level Drives Capacity Status Bootable Volume0 RAIDX(xxxxx) X XXX.
Resetting Disks to Non-RAID Take caution before you reset a RAID volume HDD to non-RAID. Resetting a RAID volume HDD deletes all internal RAID structure on the drive. To reset a RAID set hard disk drive: 1. From the utility main menu, select 3 . R e s e t D i s k s t o N o n - R A I D D, then press to display this screen. [ RESET RAID DATA ] Resetting RAID data will remove internal RAID structures from the selected RAID disks.
Resetting a RAID set hard disks drive Take caution before you reset a RAID volume HDD to non-RAID. Resetting a RAID volume HDD deletes all internal RAID structure on the drive. To reset a RAID set hard disk drive: 1. From the utility main menu, select [ 3 . R e s e t D i s k s t o N o n - R A I D ]], then press to display the following screen. [ RESET RAID DATA ] Resetting RAID data will remove the internal RAID structures from the selected RAID disks.
5.5.3 Silicon Image® RAID configurations The Silicon Image RAID controller supports RAID 0 and RAID 1 configuration. Use the Silicon Image RAID utility to configure a disk array. Setting the RAID item in BIOS You must set the RAID item in the BIOS Setup before you can create a RAID set(s). To do this: 1. 2. Enter the BIOS Setup during POST. Go to the A d v a n c e d menu, select O n b o a r d D e v i c e s Configuration n, then press .
RAID Configuration Utility - Silicon Image Inc.
Creating as RAID 0 set (Striped) To create a RAID 0 set: 1. 2. 3. From the Silicon Image configuration utility main menu, select Create RAID set then press to display an option menu. MAIN MENU Create RAID set Delete RAID set Rebuild Raid1 set Resolve Conflicts Low Level Format Logical Drive Info RAID0 RAID1 RAID5 RAID10 SPARE DRIVE JBOD Select R A I D 0 0, then press . MAIN MENU Select your desired method of configuration, Auto configuration Manual configuration then press .
b. When the selection bar moves to the P h y s i c a l D r i v e section, use the up or down arrow keys to select the first drive of the RAID set, then press . PHYSICAL DRIVE 0 1 2 3 XXXXXXXXXXX XXXXXXXXXXX XXXXXXXXXXX XXXXXXXXXXX XXXXXXMB XXXXXXMB XXXXXXMB XXXXXXMB c. Repeat step b to set the second, third, and fourth drive. The number of available drives depends on the installed and enabled physical drives in the system. d.
Auto configuration When you select A u t o c o n f i g u r a t i o n n, a confirmation message appears. Press to automatically create a RAID 1 set. • Auto-configuration creates a RAID 1 set without backup copy. • When migrating a single hard disk drive to a RAID 1 set, we recommend that you use M a n u a l c o n f i g u r a t i o n . Manual configuration a. When you select M a n u a l configuration n, the selection bar moves to the P h y s i c a l D r i v e section.
d. If you selected Create with data copy y, a pop-up menu appears. Use the up or down arrow keys to select a copy method, then press . MAIN MENU Auto configuration Manual configuration online copy offline copy The o n l i n e c o p y option automatically copies the data to the target drives on the background while writing to the source drives. The o f f l i n e c o p y option allows you to copy the contents of the source drive to the target drives immediately. e.
5.5 Creating a RAID driver disk A floppy disk with the RAID driver is required when installing Windows® 2000/XP operating system on a hard disk drive that is included in a RAID set. You can create a RAID driver disk in DOS (using the Makedisk application in the support CD) or in Windows® environment. To create a RAID driver disk in DOS environment: 1. Place the motherboard support CD in the optical drive. 2. Restart the computer, then enter the BIOS Setup. 3.
9. The RAID drivers are copied to the floppy disk. After creating a RAID driver disk, eject the floppy disk, then write-protect it to prevent computer virus infection. 10. Press any key to return to the Makedisk menu. To create a RAID driver disk in Windows® environment: 1. Place the motherboard support CD in the optical drive. 2.
3. Insert a formatted high-density floppy disk to the floppy disk drive. 4. Follow screen instructions to complete the process. 5. After creating a RAID driver disk, eject the floppy disk, then write-protect it to prevent computer virus infection. To install the RAID driver: 1. Install an operating system to the selected hard disk drive. During installation, the computer prompts you to press the F 6 key if you are installing a third-party SCSI or RAID driver. 2.
5-38 Chapter 5: Software support
The Appendix describes the CPU features and technologies that the motherboard supports.
Chapter summary A A.1 Intel® EM64T ........................................................................ A-1 A.2 Enhanced Intel SpeedStep® Technology (EIST) .................... A-1 A.3 Intel® Hyper-Threading Technology ......................................
A.1 Intel® EM64T • The motherboard is fully compatible with Intel® Pentium® 4 LGA775 processors running on 32-bit operating systems. • The motherboard comes with a BIOS file that supports EM64T. You can download the latest BIOS file from the ASUS website (www.asus.com/support/download/) if you need to update the BIOS file. See Chapter 4 for details. • Visit www.intel.com for more information on the EM64T feature. • Visit www.microsoft.com for more information on Windows® 64-bit OS.
A.2.2 Using the EIST To use the EIST feature: 1. 2. Turn on the computer, then enter the BIOS Setup. Go to the Advanced Menu Menu, highlight CPU Configuration Configuration, then press . 3. Set the Intel(R) SpeedStep Technology item to [Automatic], then press . See page 4-27 for details. 4. Press to save your changes and exit the BIOS setup. 5. After the computer restarts, right click on a blank space on the desktop, then select Properties from the pop-up menu.
A.3 Intel® Hyper-Threading Technology • The motherboard supports Intel® Pentium® 4 LGA775 processors with Hyper-Threading Technology. • Hyper-Threading Technology is supported under Windows® XP/2003 Server and Linux 2.4.x (kernel) and later versions only. Under Linux, use the Hyper-Threading compiler to compile the code. If you are using any other operating systems, disable the Hyper-Threading Technology item in the BIOS to ensure system stability and performance.
A-4 Appendix: CPU features