Motherboard P8B-C 系列
C6852 第二版 V2 2011 年 9 月 版權所有‧不得翻印 © 2011 華碩電腦 本產品的所有部分,包括配件與軟件等,其相關知識產權等歸華碩電腦公司 (以下簡稱華碩)或授權華碩使用的相關主體所有,未經權利主體許可,不得 任意地仿製、拷貝、摘抄或轉譯。本用戶手冊沒有任何型式的擔保、立場表達 或其它暗示。若有任何因本用戶手冊或其所提到之產品信息,所引起直接或 間接的數據流失、利益損失或事業終止,華碩及其所屬員工恕不為其擔負任何 責任。除此之外,本用戶手冊所提到的產品規格及信息只作參考,內容亦會隨 時更新,恕不另行通知。 下列因素導致的產品故障或損壞不在免費保修範圍內: A. 因天災(水災、火災、地震、雷擊、颱風等)、遇不可抗拒外力或人為之操 作使用不慎造成之損害。 B. 自 行拆裝、修理、或將產品送至非華碩認証之維修點進行檢測維修。 C. 用 戶擅自或請第三人修改、修復、變更規格及安裝、添加、擴充非本公 司原廠銷售、授權或認可之配件所引起之故障與損壞。 D. 因用戶自行安裝軟件及設定不當所造成之使用問題及故障。 E. 計算機病毒所造成之問題及故障。 F.
目錄內容 安全性須知.................................................................................................................. vii 電氣方面的安全性...................................................................................... vii 操作方面的安全性...................................................................................... vii REACH vii 關於這本用戶手冊................................................................................................... viii 用戶手冊的編排方式.....................................................
目錄內容 2.5 2.6 2.7 擴展插槽.................................................................................................. 2-21 2.5.1 安裝擴展卡............................................................................. 2-21 2.5.2 設置擴展卡............................................................................. 2-21 2.5.3 指定中斷要求......................................................................... 2-22 2.5.4 PCI Express x8 插槽 (x4 link)........................................ 2-23 2.5.
目錄內容 4.4 事件記錄菜單(Event Logs )...................................................... 4-12 4.5 高級菜單(Advanced).................................................................... 4-14 4.5.1 ACPI 設置............................................................................... 4-14 4.5.2 可信計算(Trusted Computing)................................. 4-15 4.5.3 WHEA 設置(WHEA Configuration)........................ 4-15 4.5.4 處理器設置(CPU Configuration)............................. 4-16 4.5.5 北橋設置(North Bridge).......
目錄內容 5.3.2 創建修復磁區......................................................................... 5-27 5.3.3 刪除 RAID 磁區.................................................................... 5-29 5.3.4 重新設置硬盤為非陣列硬盤............................................. 5-30 5.3.5 Recovery Volume 選項...................................................... 5-31 5.3.6 退出 Intel® Rapid Storage Technology....................... 5-32 5.3.7 重建 RAID...............................................................................
安全性須知 電氣方面的安全性 • 為避免可能的電擊造成嚴重損害,在搬動電腦主機之前,請先將電腦電 源線暫時從電源插槽中拔掉。 • 當您要加入硬件設備到系統中或者要去除系統中的硬件設備時,請務必 先連接該設備的數據線,然後再連接電源線。可能的話,在安裝硬件設 備之前先拔掉電腦電源的電源線。 • 當您要從主板連接或拔除任何的數據線之前,請確定所有的電源線已事 先拔掉。 • 在使用擴展卡或擴展卡之前,我們建議您可以先尋求專業人士的協助。 這些設備有可能會干擾接地的迴路。 • 請確定電源的電壓設置已調整到本國/本區域所使用的電壓標準值。若您 不確定您所屬區域的供應電壓值為何,那麼請就近詢問當地的電力公司 人員。 • 如果電源已損壞,請不要嘗試自行修復。請將之交給專業技術服務人員 或經銷商來處理。 操作方面的安全性 • 在您安裝主板以及加入硬件設備之前,請務必詳加閱讀本手冊所提供的 相關信息。 • 在使用產品之前,請確定所有的排線、電源線都已正確地連接好。若您 發現有任何重大的瑕疵,請儘速聯絡您的經銷商。 • 為避免發生電氣短路情形,請務必將所有沒用到的螺絲、回型針及其他 零件收好,不要遺留在主板上
關於這本用戶手冊 產品用戶手冊包含了所有當您在安裝華碩 P8B-C 系列主板時所需用到的 信息。 用戶手冊的編排方式 用戶手冊是由下面幾個章節所組成: • 第一章:產品介紹 本章節描述本主板的功能和新技術。 • 第二章:硬件設備信息 本章節描述所有您在安裝系統元件時必須完成的硬件安裝程序。詳細內 容有:處理器與內存安裝、跳線選擇區設置以及主板的各種設備接口。 • 第三章:開啟電源 本章節說明開啟電腦電源的順序以及電腦開機後所發出各種不同類型 嗶嗶聲的代表意義。 • 第四章:BIOS 程序設置 本章節描述如何使用 BIOS 設置程序中的每一個菜單項目來更改系統的 設置。此外也會詳加介紹 BIOS 各項設置值的使用時機與參數設置。 • 第五章: RAID 磁盤陣列設置 本章節提供本主板的 RAID 設 置 信息。 • 第六章:安裝驅動程序 本章節介紹本主板驅動程序的安裝。 • 附錄:相關信息 本附錄中包含您在設置本主板時有可能會用到的信息。 viii
提示符號 為了能夠確保您正確地完成主板設置,請務必注意下面這些會在本手冊中 出現的標示符號所代表的特殊含意。 警告:提醒您在進行某一項工作時要注意您本身的安全。 心:提醒您在進行某一項工作時要注意勿傷害到電腦主板元 小 件。 要:此符號表示您必須要遵照手冊所描述之方式完成一項或多項 重 軟硬件的安裝或設置。 注意:提供有助於完成某項工作的訣竅和其他額外的信息。 跳線帽及圖標說明 主板上有一些小小的塑料套,裡面有金屬導線,可以套住選擇區的任二隻 針腳(Pin)使其相連而成一通路(短路),本手冊稱之為跳線帽。 有關主板的跳線帽使用設置,茲利用以下圖 標說明。以下圖為例,欲設置為「Jumper™ Mode」,需在選擇區的第一及第二隻針腳部份 蓋上跳線帽,本手冊圖標即以塗上底色代表蓋上 跳線帽的位置,而空白的部份則代表空接針。以 文字表示為:[1-2]。 1 2 Jumper Mode 2 3 Jumper Free (Default) 因此,欲設置為「JumperFree™ Mode」,以右圖表示即為在「第二及第 三隻針腳部份蓋上跳線帽」,以文字表示即為:[2-3]。 哪裡可以找到更多的產品信息
30 電子信息產品污染控制標示:圖中之數字為產品之環保使用期 限。僅指電子信息產品中含有的有毒有害物質或元素不致發生 外洩或突變從而對環境造成污染或對人身、財產造成嚴重損害 的期限。 有毒有害物質或元素的名稱及含量說明標示: 部件名稱 印刷電路板 及其電子 組件 外部信號連 接頭及線材 外殼 軟驅 電池 光驅 散熱設備 電源適配器 硬盤 中央處理器 與內存 有害物質或元素 鉛 (Pb) 汞 (Hg) 鎘 (Cd) x o o 六價鉻 (Cr(VI)) o 多溴聯苯 多溴二苯 (PBB) 醚(PBDE) o o x o o o o o x x x x x x x x o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o ○: 表 示 該 有 毒 有 害 物 質 在 該 部 件 所 有 均 質 材 料 中 的 含 量 均 在 S J / T 11363-2006 標准規定的限量要求以下。 ×: 表 示 該 有 毒 有 害 物 質 至 少 在 該 部 件 的 某 一
P8B-C 系列規格概要 型號 P8B-C/4L 處理器/系統總線 核心邏輯 尺寸 華碩獨家功能 內存 風扇速度控制 Rack Ready (Rack 與 Pedestal 雙用途) ASWM Enterprise 插槽總數 容量 內存類型 PCI/PCI-X/PCI-E 擴展插槽 (依照 SSI 位置 插槽總數 號排列) 插槽 1 插槽 2 插槽 3 插槽 4 插槽 5 插槽 6 插槽 7 存儲 SATA 控制器 SAS 控制器 網絡 LAN 顯卡 VGA 內部 I/O 接口 TPM 接口 電源接口 USB 接口 風扇接口 機箱開啟警告 串口插座 P8B-C/SAS/2L* P8B-C/SAS/4L 1 x LGA1155 插槽 Intel® Xeon® E3-1200 系列處理器 Intel® Core™ i3-2100 系列處理器 Intel® C202 芯片組 Intel® C204 芯片組 ATX 規格 12”x 9.
P8B-C 系列規格概要 型號 後側面板 I/O 接口 監控 環境要求 P8B-C/4L 外接 USB 接口 VGA 接口 RJ-45 PS/2 鍵盤/鼠標 CPU 溫度 風扇轉速 P8B-C/SAS/2L* 2 1 4 2 1 V V 操作溫度:10℃ – 35℃ 非操作溫度:-40℃ – 70℃ 非操作濕度:20% – 90% (非冷凝) P8B-C/SAS/2L 僅限在特定區域銷售。 *規格若有任何變更,恕不另行通知。 xii P8B-C/SAS/4L 4
您可以在本章節中發現諸多華碩所賦予本 主板的優異特色,利用簡潔易懂的說明,讓 您能很快的掌握本主板的各項特性,當然, 在本章節我們也會提及所有能夠應用在本主 板的新產品技術。 1 第一章:產品介紹
1 章節提綱 1.1 歡迎加入華碩愛好者的行列!........................................................... 1-3 1.2 產品包裝..................................................................................................... 1-3 1.3 序列號標籤................................................................................................ 1-4 1.4 特殊功能.....................................................................................................
1.1 歡迎加入華碩愛好者的行列! 再次感謝您購買此款華碩 P8B-C 系列主板! 本主板的問世除了再次展現華碩對於主板一貫具備的高質量、高性能以 及高穩定度的嚴格要求,同時也添加了許多新的功能以及大量應用在它身上 的最新技術,使得 P8B-C 系列主板成為華碩優質主板產品線中不可多得的 閃亮之星。 在您拿到本主板包裝盒之後,請馬上檢查下面所列出的各項標準配件是 否齊全。 1.
1.3 序列號標籤 在請求華碩技術支持團隊的技術支持之前,請務必留意一下主板的序列 號,此序列號由 12 位字母組成(xxS1xxxxxxxx),如下圖所示。只有當 您了解產品的正確序列號,華碩技術支持團隊成員才能針對您提出的問題提 供更快速而讓您滿意的解決方案。 P8B-C series xxS1xxxxxxxx Made in China 合格 1.4 特殊功能 1.4.
支持 DDR3 內存 P8B-C 主板支持 UDIMM DDR3 內存,擁有 1333/1066 MHz 數據傳輸速 率,可以符合像是 3D 繪圖、多媒體與網絡應用等更高的系統帶寬需求。雙 通道 DDR3 架構使系統內存帶寬加倍,最高可達 21GB/s,可以顯著提升您 系統平台的性能,並降低帶寬的瓶頸。另外,內存電壓由 DDR2 的 1.8 V 降低到了現在 DDR3 的 1.5V。降低電壓減少了電能消耗,並降低了 DDR3 內存產生的熱量,是絕佳的內存解決方案。 PCIe 2.0 本主板支持最新 P C I e 2.0 設備,使系統速度與帶寬加倍,提升系統性 能。PCIe 2.0 同時向下兼容 PCIe 1.
溫度、風扇和電壓監測 CPU 溫度由芯片來監測,以防過熱損壞。系統風扇的每分鐘轉速 (RPM) 也被實時監測。此外,芯片還會監測電壓以確保重要元件上的電壓穩定。 1.4.
本章節描述了所有您在安裝系統元 件時所必須完成的硬件安裝程序。詳 細內容有:處理器與內存、跳線選擇 區設置以及主板的各種設備接口。 2 第二章:硬件設備 信息
2 章節提綱 2.1 主板安裝前................................................................................................ 2-3 2.2 主板概觀..................................................................................................... 2-4 2.3 中央處理器(CPU)........................................................................... 2-10 2.4 系統內存.................................................................................................. 2-16 2.5 擴展插槽..................................................
2.
2.2 主板概觀 在您開始安裝之前,請確定您所購買的電腦主機機箱是否可以容納本主 板,並且機箱內的主板固定孔位是否能與本主板的螺絲孔位吻合。 為了優化主板功能,建議您將主板安裝在一個兼容 ATX 1.1 的機箱內。 為方便在電腦主機機箱安裝或取出主板,請務必先將電源供應器 移開!當您安裝或移除主板的時候,必須確保電源供應器的插頭 已經被移除,否則可能導致主板上的元件損壞。 2.2.1 主板的擺放方向 當您安裝主板到電腦主機機箱內時,務必確認置入的方向是否正確。帶 有外部接口的方向應是朝向主機機箱的後方面板,而且您也會發現主機機箱 後方面板會有相對應的預留孔位。請參考下圖所示。 2.2.
2.2.3 主板構造圖 P8B-C/4L (R1.
P8B-C/4L (R2.
P8B-C/SAS/2L (R1.
P8B-C/SAS/2L (R2.
P8B-C/SAS/4L (R1.
P8B-C/SAS/4L (R2.
2.2.4 主板元件說明 插槽 1. 中央處理器插槽 頁數 2-13 2. DDR3 內存插槽 2-19 3. PCI Express x8 / PCI Express x16 / PCI 插槽 2-22 跳線 頁數 1. CMOS 數據清除 (CLRTC1) 2-25 2. VGA 控制器設置 (3-pin VGA_SW1) 2-26 3. 中央處理器與機箱風扇控制設置 (3-pin CPUFAN_SEL1, CHAFAN_SEL1) 2-27 4. LAN 控制器設置 (3-pin LAN_SW1–2, 僅 P8B-C/SAS/2L ) 3-pin LAN_SW1–4, 僅 P8B-C/4L, P8B-C/SAS/4L ) 2-28 5. RAID 設置程序選擇 (3-pin RAID_SEL1) (僅 P8B-C/4L) 2-28 6. 強制 BIOS 恢復設置 (3-pin RECOVERY1) (僅 R1.0X) 2-29 7. 機箱開啟警告排針 (2-pin CHASSIS) 2-30 8.
2-12 內部連接插槽 頁數 1. Serial ATA 接口 P8B-C/4L : (SATA 3Gb/s: 7-pin SATA1–6 [黑色]) P8B-C/SAS/2L, P8B-C/SAS/4L : (SATA 6Gb/s: 7-pin SATA1–2 [藍色]) (SATA 3Gb/s: 7-pin SATA3–6 [黑色]) 2-33 2. SAS 接口 (7-pin SAS1 - 4 [藍色]) (7-pin SAS5 - 8 [黑色]) (僅 P8B-C/SAS/2L, P8B-C/SAS/4L) 2-34 3. 硬盤讀寫動作指示燈連接排針 (4-pin HDLED1) 2-34 4. USB 接口 (10-1 pin USB34, USB56; A-Type USB7) 2-35 5. 並口連接插槽 (26-1 pin LPT1) 2-35 6.
2.3 中央處理器(CPU) 本主板具備一個 L G A1155 處理器插槽,本插槽是專為 L G A 封裝的 Intel® Xeon E3-1200/Core™ i3-2100 系列處理器所設計。 • 在您購買本主板之後,請確認在處理器插座上附有一個 PnP 保 護蓋,並且插座接點沒有彎曲變形。若是保護蓋已經毀壞或是 沒有保護蓋,或者是插座接點已經彎曲,請立即與您的經銷商 聯絡。 • 在 安 裝 完 主 板 之 後 , 請 將 P n P 保 護 蓋 保 留 下 來 。 只 有 LGA1155 插槽上附有 PnP 保護蓋的主板符合 Return Merchandise Authorization(RMA)的要求,華碩電腦才能 為您處理產品的維修與保修。 • 本保修不包括處理器插座因遺失、錯誤的安裝或不正確的移除 PnP 保護蓋所造成的毀壞。 2.3.1 安裝中央處理器 請依照以下步驟安裝處理器: 1. 找到位於主板上的處理器插槽。 在安裝處理器之前,請先將主板上的處理器插槽面向您,並且確 認插槽的固定扳手位在您的左手邊。 2.
3. 將插座側邊的固定板手按照箭頭方 向拉起至上蓋完全打開。 安裝 盒上蓋 4. 從 CPU 插槽中將 PnP 保護蓋向外 推並取下。 PnP 保護蓋 固定扣 5.
6. 在 CPU 裸露在外面的區域上滴入 几滴散熱膏,與散熱片接觸。散熱 器散熱膏必須只有很薄的一層。 有些散熱片已有散熱膏。 如果是,則跳過這一步。 注意:這些散熱膏有毒且 不能食用。請勿食用散熱 膏。如進入眼睛或皮膚, 請立即清洗,並尋求專業 醫學幫助。 7. 將上蓋(A)重新蓋上,接著將固 定拉桿(B)朝原方向推回并扣于 固定扣上(C)。 B A C 8.
2.3.2 安裝散熱器和風扇 Intel ® LGA1155 處理器需要搭配安裝經過特殊設計的散熱器與風扇,方 能得到最佳的散熱性能。 • 若您所購買的是盒裝 Intel 處理器,則產品包裝中即已內含有一 組專用的散熱器與風扇;若您所購買的是散裝的處理器,請確 認您所使用的 CPU 散熱器已通過 Intel 的相關認證。 • 盒裝 Intel LGA1155 處理器包裝中的散熱器與風扇採用下推式 固定扣具,因此無須使用任何工具進行安裝。 • 請務必使用兼容 LGA1155 處理器的散熱器與風扇。LGA1155 處理器插槽不兼容 LGA775 與 LGA1366 處理器插槽的大小尺 寸。 若您所購買的是散裝的 CPU 散熱器與風扇,請在安裝之前確認風 扇散熱器上的金屬銅片或者是 CPU 上面有確實塗上散熱膏。 在安裝處理器的風扇和散熱器之前,請先確認主板已經安裝至機 箱上。 請依照下面步驟安裝處理器的散熱器 和風扇: 1. 將散熱器放置在已安裝好的 CPU 上 方,並確認主板上的四個孔位與散熱 器的四個扣具位置相吻合。 A B B 2.
3. 當風扇、散熱片以及支撐機構都已安裝完畢,接著請將風扇的電源線插 到主板上標示有“CPU_FAN1”的電源插槽。 若您未連接 CPU_FAN 1 的電源插槽,可能將會導致啟動時 CPU 溫度過熱並出現“Hardware monitoring errors”的信息。 2.3.3 卸除散熱器與風扇 A 請按照以下的步驟卸除散熱器和風 扇: 1. 先將主板上連接 CPU 散熱器的電 源線從 CPU_FAN 上移除。 B B 2. 將每個扣具上的旋鈕以逆時鐘方向 旋轉,鬆開散熱器固定扣具。 A 3. 依照順序將扣具扳離主板上的散熱 器插孔,採對角線方式移除,例 如:先移除 A,再移除 B;或是先 移除 B,再移除 A。 A B B A 4.
2.3.4 安裝散熱器 Intel ® LGA1155 處理器需要搭配安裝經過特殊設計的散熱器與風扇,方 能得到最佳的散熱性能。 • 請確認您使用合格的散熱器。 •請在安裝散熱器與風扇之前確認 CPU 上面有塗上散熱膏。 1. 取下散熱器金屬片上的貼條,將金屬片放置在主板的反面,并確認四個 螺栓與散熱器的四個螺絲孔相吻合。 2.
2.4 系統內存 2.4.1 概觀 本主板配置有四組 DDR3 DIMM(Double Data Rate,雙倍數據傳輸率) 內存插槽。 DDR3 內存條擁有與 DDR2 內存條相同的外觀,但是實際上 DDR3 內存 條的缺口與 DDR2 內存條不同,以防止插入錯誤的內存條。DDR3 內存條 擁有更高的性能與更低的能耗。 下圖所示為 DDR3 內存插槽在主板上的位置。 2.4.
2.4.3 安裝內存條 安裝/移除內存條或其他的系統元件之前,請先暫時拔出電腦的 電源線。如此可避免一些會對主板或元件造成嚴重損壞的情況發 生。 請依照下面步驟安裝內存條: 1. 先將內存條插槽兩端的白色固定 內存條插槽 卡扣扳開。 2. 將內存條的金手指對齊內存條插 槽的溝槽,並且在方向上要注意 金手指的缺口要對準插槽的凸起 點。 1 2 1 插槽凸起點 向外扳開插槽兩 端的卡扣 由於 DDR3 內存條金手指部份均有缺口設計,因此只能以一個固 定方向安裝到內存條插槽中。請勿強制插入以免損及內存條。 3. 最後緩緩將內存條插入插槽中,若 無錯誤,插槽兩端的白色卡扣會因 內存條置入而自動扣到內存條兩側 的凹孔中。 3 3 卡扣會在內存條正確 安裝後自動扣上 DDR3 內存插槽並不支持 DDR 與 DDR2 內存條,請勿將 DDR 與 DDR2 內存條安裝至 DDR3 內存插槽上。 2.4.4 取出內存條 2 請依照以下步驟取出內存條: 1. 同時壓下內存條插槽兩端白色的 固定卡扣以鬆開內存條。 1 2.
2.5 擴展插槽 考慮到未來會擴展系統機能的可能性,本主板提供了擴展插槽,在接下 來的子章節中,將會描述主板上這些擴展插槽的相關信息。 安裝/移除任何擴展卡之前,請暫時先將電腦的電源線拔出。如 此可免除因電氣殘留於電腦中而發生的意外狀況。 2.5.1 安裝擴展卡 請依照下列步驟安裝擴展卡: 1. 在安裝擴展卡之前,請先詳讀該擴展卡的使用說明,並且要針對該卡作 必要的硬件設置更改。 2. 鬆開電腦主機的機箱蓋並將之取出(如果您的主板已放置在主機內)。 3. 找到一個您想要插入新擴展卡的空置插槽,並以十字螺絲起子鬆開該插 槽位於主機背板的金屬擋板的螺絲,最後將金屬擋板移出。 4. 將擴展卡上的金手指對齊主板上的擴展槽,然後慢慢地插入槽中,並以 目視的方法確認擴展卡上的金手指已完全沒入擴展槽中。 5. 再用剛才鬆開的螺絲將擴展卡金屬擋板鎖在電腦主機背板以固定整張 卡。 6. 將電腦主機的機箱蓋裝回鎖好。 2.5.2 設置擴展卡 在安裝好擴展卡之後,接著還須通過軟件設置來調整該擴展卡的相關設 置。 1.
2.5.
2.5.4 PCI Express x8 插槽 (x4 link) 板載的 PCI Express x8 插槽可提供一組 x4 link 至處理器。這些插槽可 支持 VGA 卡以及服務器等級的多種高性能附加卡。 2.5.5 PCI Express x16 插槽 (x16 link) 板載的 PCI Express x16 插槽可提供一組 x16 link 至處理器。這些插槽 可支持 VGA 卡以及服務器等級的多種高性能附加卡。 2.5.6 PCI 插槽 PCI 插槽支持如網卡、USB 卡及其他符合 PCI 2.
2.5.7 連接熱敏傳感器連線 請依照以下步驟連接熱敏傳感器到主板上。 1. 找到主板上的 TR1 排針。 2. 將熱敏傳感器連線連接到排針。 您可以將熱敏傳感器連接到 pin 1-2 或 pin 2-3。 3.
2.6 跳線選擇區 1. CMOS 配置數據清除 (CLRTC1) 主板上的 CMOS 存儲器中記載著正確的時間與系統硬件配置等數據, 這些數據並不會因電腦電源的關閉而遺失數據與時間的正確性,因為這個 CMOS 的電源是由主板上的鋰電池所供應。 想要清除這些數據,可以依照下列步驟進行: 1. 關閉系統電源,拔掉電源適配器; 2. 將 CLRTC1 跳線帽由 [1-2](默認值)改為 [2-3] 約 5~10 秒鐘(此時 即清除 CMOS 數據),然后再將跳線帽改回 [1-2]; 3. 插上電源適配器,開啟電源; 4.
2. 顯示芯片控制器設置 (3-pin VGA_SW1) 此跳線可讓您開啟或關閉板載的顯示芯片控制器。將跳線設置為 [1-2] 短路為開啟顯示芯片功能。 R1.0x R2.
3.
4. LAN 控制設置 (3-pin LAN_SW1–2, 僅 P8B-C/SAS/2L ) (3-pin LAN_SW1–4, 僅 P8B-C/4L, P8B-C/SAS/4L ) 這些跳線可讓您開啟或關閉板載 Intel 82574L 千兆網絡控制器。設為 [1-2] 短路激活千兆網絡功能。 5.
6. 強制 BIOS 恢復設置 (3-pin RECOVERY1,僅 R1.0x) 此跳線可讓您在 BIOS 損壞時快速升級或恢復 BIOS 設置。 請按照以下方式升級 BIOS: 1. 準備一張存儲有主板原始或最新 BIOS 程序 (XXXX.ROM) 與 BUPDATER.EXE 的 U 盤。 2. 將此跳線設置為 [2-3] 短路。 3. 插入 U 盤並啟動系統以進行 BIOS 升級。 4. 關閉系統。 5. 將此跳線恢復為 [1-2] 短路。 6.
7. 機箱開啟警示排針 (2-pin CHASSIS) 這組排針提供給設計有機箱開啟偵測功能的電腦主機機箱之用。此 外,尚須搭配一個外接式偵測設備譬如機箱開啟偵測感應器或者微型開 關。在本功能啟用時,若您有任何移動機箱元件的動作,感應器會隨即 偵測到並且送出一信號到這組接針,最後會由系統記錄下來這次的機箱 開啟事件。 本項目的默認值是將跳線帽套在排針中標示著“Chassis Signal”與“Ground”的二個針腳上,若您想要使用本功能,請將跳線 帽從“Chassis Signal”與“Ground”的針腳上移除。 8.
9.
2.7 元件與外圍設備的連接 2.7.1 後側面板接口 1. PS/2 鼠標接口(綠色):將 PS/2 鼠標插頭連接到此端口。 2. PS/2 鍵盤接口(紫色):將 PS/2 鍵盤插頭連接到此端口。 3. USB 2.0 設備接口(1 和 2):這二組 4-pin 串行總線(USB)接口可 連接到使用 USB 2.0 規格的硬件設備。 4. VGA 接口:這組接口用來連接 VGA 顯示屏或其他與 VGA 規格兼容的 硬件設備。 5. LAN1 (RJ-45) 端口:這組接口可經網絡集線器連接至局域網(LAN), 實現千兆連接。請參考下表中各燈號的說明。 6. LAN2 (RJ-45) 端口:這組接口可經網絡集線器連接至局域網(LAN), 實現千兆連接。請參考下表中各指示燈的說明。 7. LAN3 (RJ-45) 端口 (僅 P8B-C/4L, P8B-C/SAS/4L):這組接口可經網絡 集線器連接至局域網(LAN),實現千兆連接。請參考下表中各燈號的說 明。 8.
2.7.2 內部連接端口 1.
2. SAS 接口 (7-pin SAS1–4 [藍色]; 7-pin SAS5–8 [黑色]; 僅 P8B-C/SAS/2L, P8B-C/SAS/4L ) 本主板具備八個 Serial Attached SCSI (SAS) 接口,此種接口為新 一代存儲技術,可同時支持 Serial Attached SCSI (SAS) 與 Serial ATA (SATA)。每個插槽可連接一個設備。 3.
4. USB 擴展套件排線插槽 ( 10-1 pin USB34, USB56, A-Type USB7 ) 這些插槽可用來連接 USB 2.0 擴展端口。將 USB 擴展套件連接線連 接到 USB34 與 USB56,然後將擴展套件安裝到機箱背部的一箇空置插 槽位置。這三組 USB 擴展套件排線插槽支持 USB 2.0 規格,傳輸速率 高達 480Mbps。 5.
6. 中央處理器,前面板與後面板風扇電源插座(4-pin CPU_FAN1, FRNT_ FAN1, FRNT_FAN2, FRNT_FAN3, REAR_FAN1) 您可以將 350mA~740mA(最大 8.88W)或者一個合計為 3.15 ~6.66 安 培(最大 53.
7. 串行通用輸入輸出連接排針 (6-1 pin SGPIO1) 這些排用於 SGPIO 接口,用作為 Intel Rapid Storage Technology RAID SATA 指示燈。 8.
9. 熱敏傳感器連接排針 (3-pin TR1) 這些排針用與連接溫度監控器。將熱敏傳感器連線的一端連接到這箇 排針,另一端連接到您要監控溫度的設備。 您可以將熱敏傳感器連接排針連接至 pin 1-2 或 pin 2-3。 10.
11. TPM 連接排針(20-1 pin TPM) 這組連接排針支持 TPM 系統,該系統能夠安全存儲按鍵,電子證 書,密碼與數據。同時,該系統也有助於提高網絡安全,維護數字身份 (digital identities),保證平臺完整。 12.
13. ATX 電源插座 (24-pin ATXPWR1, 8-pin ATX12V1) 這個插座為提供給 ATX 電源使用。由電源所提供的連接插頭已經過特 別設計,只能以一個特定方向插入主板上的電源插座。找到正確的插入方 向後,僅需穩穩地將之套進插座中即可。 • 請不要忘記連接 24+8-pin 電源插座,否則系統將不會開機。 • 如果您想要安裝其他的硬件設備,請務必使用較高功率的電 源供應器以提供足夠的設備用電需求。若電源供應器無法提 供設備足夠的用電需求,則系統將會變得不穩定或無法開 啟。 • 此主板支持 ATX 2.
14. 系統控制面板連接排針 (20-1 pin PANEL1) 這一組連接排針包括了數個連接到電腦主機前面板的功能接針。 1. 系統電源指示燈連接排針 (3-pin PLED) 這組排針可連接到電腦主機面板上的系統電源指示燈。在您啟動電腦並 且使用電腦的情況下,該指示燈會持續亮著;而當指示燈閃爍亮著時, 即表示電腦正處於睡眠模式中。 2. 信息指示燈連接排針 (2-pin MLED) 這組排針可將信息指示燈的數據線連接至前面板信息指示燈。信息指示 燈顯示啟動狀態。啟動過程中信息指示燈會一直閃耀,直到進入系統。 3. 機箱喇叭連接排針 (4-pin SPEAKER) 這組四腳位排針連接到電腦主機機箱中的喇叭。當系統正常開機便可聽 到嗶嗶聲,若開機時發生問題,則會以不同長短的音調來警示。 4. 硬盤動作指示燈連接排針 (2-pin HDDLED) 您可以連接此組 LED 接針到電腦主機面板上的硬盤動作指示燈號,如此 一旦硬盤有讀寫動作時,指示燈隨即亮起。 5.
15. 輔助系統控制面板連接排針 (20-2 pin AUX_PANEL1) 本組接針支持前面板上的多個功能,包括前面板 SMB,Locator LED 指示燈與開關,機箱開啟警示連接排針,以及網絡狀態指示燈。 1. 前面板 SMBus 連接排針(6-1 pin FPSMB) 這組連接排針可以讓您連接 SMBus(系統管理總線)設備。 2. 網絡狀態指示燈(2-pin LAN13_LED、LAN24_LED) 這兩組 2-pin 排針可通過 Gigabit 網絡指示燈連接線來連接到 LAN 的狀 態指示燈。 3. 機箱開啟警示連接排針(4-1 pin CHASSIS) 這組排針提供給設計有機箱開啟檢測功能的電腦主機機箱之用。此外, 尚須搭配一個外接式檢測設備,譬如機箱開啟檢測感應器或者微型開 關。在本功能啟用時,若您有任何移動機箱元件的動作,感應器會隨即 檢測到並且送出一信號到這組接針,最後會由系統記錄下這次的機箱開 啟事件。默認設置為 CASEOPEN 與 GND 接腳短路,此功能關閉。 4.
1. 前面板 SMBus 連接排針(6-1 pin FPSMB) 這組連接排針可以讓您連接 SMBus(系統管理總線)設備。 2. 網絡狀態指示燈(2-pin LAN1_LED、LAN2_LED) 這兩組 2-pin 排針可通過 Gigabit 網絡指示燈連接線來連接到 LAN 的狀 態指示燈。 3. 機箱開啟警示連接排針(4-1 pin CHASSIS) 這組排針提供給設計有機箱開啟檢測功能的電腦主機機箱之用。此外, 尚須搭配一個外接式檢測設備,譬如機箱開啟檢測感應器或者微型開 關。在本功能啟用時,若您有任何移動機箱元件的動作,感應器會隨即 檢測到並且送出一信號到這組接針,最後會由系統記錄下這次的機箱開 啟事件。默認設置為 CASEOPEN 與 GND 接腳短路,此功能關閉。 4. Locator 指示燈號連接排針(2-pin LOCATORLED1、2-pin LOCATORLED2) 這兩組 2-pin 排針為 Locator 指示燈號,通過 Locator LED 連接線來連 接。當您按下 Locator 按鍵時,這個燈則會亮起顯示。 5.
2-44 第二章:硬件設備信息
本章節說明開啟電腦電源的順序,以 及電腦開機後所發出各種不同類型嗶聲 的代表意義。 3 第三章:開啟電源
3 章節提綱 3.1 第一次啟動電腦....................................................................................... 3-3 3.2 關閉電源.....................................................................................................
3.1 第一次啟動電腦 1. 確認所有排線與接腳都接妥,然後蓋上機箱的外蓋。 2. 確定所有的開關都已關閉。 3. 將電源線接上機箱背面的電輸入插座。 4. 情況許可的話,最好將電源線路上加接突波吸收/保護器。 5. 您可以先開啟以下外圍設備的電源: a. 顯示器 b. 外接存儲設備(從連接鏈中的最後一個設備開始) b. 系統電源供應器 6. 送電之後,機箱面板上應該會有電源指示燈亮起才對。如果是使用 ATX 電源供應器的話,必須等到面板按鈕被觸碰後才會啟動電源,電源指示 燈此時才會亮起。如果您的顯示器符合綠色省電標準,或具備電源待機 功能,則需要等系統 LED 指示燈亮起後,顯示器指示燈才會亮起或由橙 色切換為綠色。 如果開機過程一切順利的話,不久就可以在顯示器上看到畫面了,如果 送電之後超過 30 秒而畫面沒有動靜的話,表示電腦的設置尚有問題存 在,請再進一步地的檢查各項動作,如果還是不行,就需要向廠商求助 了! 7.
3.2 關閉電源 3.2.1 使用操作系統關閉功能 如果您使用的操作系統為 Windows® 2008 Server: 1. 點擊“開始”,將光標移動到退出右邊的三角,選擇“關機”。 2. 在“關閉事件跟蹤程序”對話框中選擇您要關機的理由。 3. 請確認您勾選了“計划的”複選框。 4. 如果需要,您可以輸入註釋。 5. 點擊“確定”。 3.2.2 使用雙重功能電源按鈕 當系統正在運行時,按下電源按鈕持續四秒以內,依 BIOS 設置將系統 調整為睡眠模式或軟關機模式。若不考慮 BIOS 設置,持續按住電源按鈕超 過4秒可使系統以進入軟關机模式。更多信息請參考第四章“4.
在電腦系統中,BIOS 程序調校的優 劣與否和整個系統的運行性能有極大的 關係。針對您自己的配備來作最優化 BIOS 設置是讓您的系統性能再提昇的 要角。接著本章節將逐一說明 BIOS 程 序中的每一項設置。 4 第四章:BIOS 程序設置
4 章節提綱 4.1 管理、更新您的 BIOS 程序................................................................. 4-3 4.2 BIOS 程序設置......................................................................................... 4-7 4.3 主菜單(Main)................................................................................... 4-10 4.4 Event Logs 菜單(Event Logs Menu).................................... 4-12 4.5 高級菜單(Advanced).................................................................... 4-14 4.6 顯示器菜單(Monitor)..
4.1 管理、更新您的 BIOS 程序 下列軟件讓您可以管理與更新主板上的 BIOS(Basic Input / Output system)設置。 1. ASUS CrashFree BIOS 3 (當 BIOS 文件遺失或損壞時,可啟動 U 盤來恢 復 BIOS 。) 2. ASUS EZ Flash 2 (使用軟盤或 USB 閃存盤更新 BIOS。) 3. BUPDATER (USB 啟動盤在 DOS 模式下更新 BIOS。) 上述軟件請參考相關章節的詳細使用說明。 建議您先將主板原始的 BIOS 程序備份到 U 盤中,以備您往後需 要再度安裝原始的 BIOS 程序。使用 BUPDATER 來拷貝主板原 始的 BIOS 程序。 4.1.
4.1.2 使用華碩 EZ Flash 升級 BIOS 程序 華碩 EZ Flash 程序讓您能輕鬆地升級 BIOS 程序,可以不必再到操作系 統模式下運行。 從華碩網站上(www.asus.com.cn)下載最新的 BIOS 文件。 請依據以下步驟使用 EZ Flash 升級 BIOS: 1. 將含有最新 BIOS 文件的 USB 閃存盤插入 USB 接口。 2. 進入 BIOS 設置程序。來到 Tools 菜單並選擇 EZ Flash 並按下 <Enter> 鍵將其開啟。 Exit ASUSTek EZ Flash BIOS ROM Utility V00.75 Flash Info MODEL: P8B-C-SAS-4L VER: 0202 DATE: 02/25/2011 fs0:\ Drive Folder Info fs0:\ ROM fs1:\ 12/09/10 10:23p 4194304 P 8 B - C s e r i e s .
•本功能僅支持採用 FAT 32/16 格式單一扇區的 USB 設備,如 USB 閃存盤。 •當升級 BIOS 時,請勿關閉或重置系統以避免系統開機失敗。 請確定讀取 BIOS 中的出廠默認值以保證系統的兼容性與穩定性。 按下 并選擇【Yes】加載 BIOS 初始設置。 4.1.2 使用 BUPDATER 升級 BIOS 程序 BUPDATER 程序讓您在 DOS 操作系統中,使用含有已更新的 BIOS 文件 的 USB 啟動盤來升級 BIOS 程序。 以下 BIOS 畫面僅供參考。實際畫面可能會有所不同。 升級 BIOS 文件: 使用 BUPDATER 升級 BIOS 程序 1. 訪問華碩網站 www.asus.com.cn 下載最新主板 BIOS 文件,并將其保存 在 U 盤中。 2. 訪問華碩技術支持網站 support.asus.com,複製 BUPDATER 程序 (BUPDATER.exe) 至您預先創建的 USB 啟動盤。 3. 在 DOS 模式中啟動系統,在提示符處輸入: BUPDATER /i[filename].
4. BUPDATER 先確認文件,然後開始升級 BIOS。 ASUSTek BIOS Update for DOS V1.06 (09/08/04) FLASH TYPE: MXIC 25L1605A Update ROM Current ROM BOARD: P8B-C-SAS-4L BOARD: P8B-C-SAS-4L VER: 0201 VER: 0202 DATE: 12/01/2010 DATE: 02/25/2011 PATH: WARNING! Do not turn off power during flash BIOS Note Writing BIOS: 當更新 BIOS 時請不要關閉或重啟系統,以防止系統啟動失敗! 5. 當 BIOS 更新完畢后該程序會返回 DOS 命令。請從硬盤重新啟動系 統。 The BIOS update is finished! Please restart your system.
4.2 BIOS 程序設置 主板擁有一片可編程的 LPC 芯片,您可以依照“4.
4.2.1 BIOS 程序菜單介紹 菜單項目 Main 功能表列 在線操作說明 設置值 Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc. Event Logs Advanced Monitor Boot Tool Exit BIOS Information BIOS Version Build Date 0202 x64 02/25/2011 Set the Date, Use Tab to switch between Data elements. CPU Information Intel(R) Xeon(R) CPU E31230 @ 3.
4.2.3 菜單項目 於功能表列選定選項時,被選擇的功能將會反白,如右圖紅線所框選的地 方,即選擇 Main 菜單所出現的項目。 點擊菜單中的其他項目(如:Advanced、Monitor、Boot、Tool 與 Exit) 也會出現該項目不同的選項。 4.2.4 子菜單 在菜單畫面中,若功能選項前面有一個小三角形標記,代表此為子菜單, 您可利用方向鍵來選擇,並按下 鍵來進入子菜單。 4.2.5 導航鍵 在菜單屏幕右下角有設置 BIOS 程序的導航鍵。使用導航鍵選擇菜單中的 項目并更改設置。 4.2.6 在線操作說明 在菜單畫面的右上方為目前所選擇的作用選項的功能說明,此說明會依選 項的不同而自動更改。 4.2.7 設置值 此區域顯示菜單項目的設置值。這些項目中,有的功能選項僅為告知用戶 目前運行狀態,並無法更改,此類項目就會以淡灰色顯示。而可更改的項目, 當您使用方向鍵移動項目時,被選擇的項目以反白顯示。 設置值被選擇後以反白顯示。要改變設置值請選擇此項目,並按下 <Enter> 鍵以顯示設置值列表。 4.2.
4.3 主菜單(Main) 當您進入 BIOS 設置程序時,首先出現的第一個畫面即為主菜單,內容如 下圖。 Main Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc. Event Logs Advanced Monitor Boot Tool Exit BIOS Information BIOS Version Build Date Set the Date, Use Tab to switch between Data elements. 0202 x64 02/25/2011 CPU Information Intel(R) Xeon(R) CPU E31230 @ 3.20GHz Memory Information Total Memory 1024 MB System Date System Time Access Level [Wed 03/09/2011] [15:07:28] Administrator Security 4.3.
管理員密碼(Administrator Password) 若您已經設置了一個管理員密碼,建議您輸入管理員密碼來進入系統。否 則,您只能看到或變更 BIOS 設置程序中的部分內容。 請依照以下步驟設置系統管理員密碼: 1. 選擇【Administrator Password】項目並按下 <Enter>。 2. 在“Create New Password”窗口出現時,輸入欲設置的密碼,輸入完 成按下 <Enter>。 3. 在彈出的確認窗口中再一次輸入密碼以確認密碼正確。 請依照以下步驟變更系統管理員密碼: 1. 選擇【Administrator Password】項目並按下 <Enter>。 2. 在“Enter Current Password”窗口出現時,輸入現在的密碼,輸入完成 按下 <Enter>。 3. 在“Create New Password”窗口出現時,輸入欲設置的新密碼,輸入 完成按下 <Enter>。 4.
4.4 事件記錄菜單(Event Logs ) 事件記錄菜單(Event Logs)選項允許您更改事件記錄設置以及查看系 統事件記錄。 Main Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc. Event Logs Advanced Monitor Boot Tool Exit Change Smbios Event Log Settings View Smbios Event Log Press to change the Smbios Event Log configuration. 更改 Smbios Event Log 設置 Main Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc.
Log OEM Codes [Enabled] 允許您開啟或關閉 EFI 狀態編碼記錄作為 OEM 編碼。設置值有: [Disabled] [Enabled] Convert OEM Codes [Disabled] 允許您開啟或關閉 EFI 狀態編碼轉變為標準 Smbios 編碼。設置值 有:[Disabled] [Enabled] View Smbios Event Log 按下 查看 Smbios 項目登錄時間。 華碩 P8B-C 系列主板用戶手冊 4-13
4.5 高級菜單(Advanced) 高級菜單可讓您改變中央處理器與其他系統設備的細部設置。 注意!在您設置本高級菜單的設置時,不正確的數值將導致系統 損壞。 Main Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc. Event Logs Advanced Monitor Boot Tool Exit System ACPI Parameters ACPI Settings Trusted Computing WHEA Configuration CPU Configuration North Bridge South Bridge SATA Configuration Intel TXT(LT) Configuration USB Configuration Onboard Devices Configuration APM Serial Port Console Redirection 4.5.
4.5.2 可信計算(Trusted Computing) Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc. Advanced TPM Configuration TPM SUPPORT [Disabled] Current TPM Status Information NO TPM Hardware Enables or Disables TPM support. O.S. will not show TPM. Reset of platform is required. TPM Support [Disabled] 本項目用來開啟或關閉 TPM 支持。設置值有:[Disabled] [Enabled] 4.5.3 WHEA 設置(WHEA Configuration) Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc.
4.5.4 處理器設置(CPU Configuration) 本項目可讓您得知中央處理器的各項信息與變更中央處理器的相關設 置。若處理器不支持某些功能,則這些功能不顯示。 Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc. Advanced Includes TM1, TM2 and EMTTM CPU Configuration Intel(R) Xeon(R) CPU E31230 @ 3.
Intel(R) Virtualization Tech [Enabled] Intel® Virtualization 技術支持一塊硬盤上分別或同時運行多個操作系統,可 讓一個系統虛擬地發揮多個系統的功能。設置值有:[Disabled] [Enabled] Enchanced SpeedStep (TM) Tech [Enabled] 允許您開啟或關閉增強型 Intel® SpeedStep 技術(EIST)。設置值有: [Disabled] [Enabled] TurboMode [Enabled] Turbo 模式允許處理器核心在特定狀態下以高於標示頻率運行。設置值 有:[Disabled] [Enabled] CPU C1E [Enabled] 本項目允許您開啟或關閉支持 Enhanced Halt State。設置值有:[Disabled] [Enabled] C3 State [Enabled] 本項目允許您選擇 CPU C3 動作。 C6 State [Enabled] 本項目允許您選擇 CPU C6 動作。 Package C State limit [No Limit] 設置值有
4.5.5 北橋設置(North Bridge) 北橋內置於 CPU 內。 Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc.
4.5.7 SATA 設備設置(SATA Configuration) 當您進入 B I O S 設置程序時,程序會自動檢測系統已存在的 S ATA 設 備。若對應接口中沒有安裝 SATA 設備,則【SATA Port】項目顯示為 [Not Present]。 Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc. Advanced SATA Configuration SATA Mode Serial-ATA Controller 0 Serial-ATA Controller 1 S.M.A.R.T. Status Check SATA SATA SATA SATA SATA SATA [IDE Mode] [Enhanced] [Enhanced] [Enabled] Port1 Port2 Port3 Port4 Port5 Port6 (1) IDE Mode. (2) AHCI Mode. (3) RAID Mode. ST3160812AS (160.
4.5.8 Intel TXT(LT) Configuration Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc. Advanced Enables Legacy USB support. AUTO option disables legacy Intel TXT support only can be enabled/disabled if SMX support if no USB devices are is enabled. VT and VT-d support must also be enabled connected. DISABLE option will keep USB devices available prior to TXT. only for EFI applications.
USB transfer time-out [20 sec] 允許您選擇 USB 轉移暫停值。設置值有:[1 sec] [5 sec] [10 sec] [20 sec] Device reset time-out [20 sec] 允許您選擇 USB 設備重置暫停值。設置值有:[10 sec] [20 sec] [30 sec] [40 sec] Device power-up delay [Auto] 設置值有:[Auto] [Manual] Device power-up delay in seconds [XX] 僅當【Device power-up delay】項目設置為 [manual] 時此選擇才會出 現,使用 <+> 與 <-> 方向鍵調節設置值。設置值以一秒為間隔,在 1 至 40 之間變化。 4.5.10 內置設備設置 (Onboard Devices Configuration) 本菜單允許您對於內置設備進行高級設置。 Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc.
Change Settings [Auto] 允許您選擇串口基地位址。 設置值有:[Auto] [IO=3F8h; IRQ=4] [IO=3F8h: IRQ=3, 4, 5, 6, 7, 9, 10, 11, [IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, [IO=3E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, [IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12] 12] 12] 12] Serial Port 2 Configuration 這個子項目允許您設置串口 2 設置。 Serial Port [Enabled] 允許您開啟或關閉串口(COM)。 設置值有:[Enabled] [Disabled] Change Settings [Auto] 允許您選擇串口基地位址。 設置值有:[Auto] [IO=2F8h; IRQ=3] [IO=3F8h: IRQ=3, 4, 5, 6, 7, 9, 10, 11, [IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, [IO=3E8h;
4.5.11 高級電源管理設置(APM) Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc. Advanced Restrore AC EuP Ready Power On By Power On By Power On By Power On By Power Loss PCI PCIE Ring RTC [Power Off] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] Specify what state to go to when power is re-applied after a power failure (G3 state).
4.5.12 串口控制台重定向(Serial Port Console Redirection) Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc.
Stop Bits [1] 停止位指的是串聯數據包的終端。設置值有:[1] [2] Flow Control [Hardware RTS/CTS] 流量控制可防止緩衝過度時的數據丟失。設置值有:[N o n e] [Hardware RTS/CTS] Recorder Mode [Disabled] 開啟此選項只能發送文本。該選項用來捕捉終端數據。設置值有: [Disabled] [Enabled] Legacy OS Redirction Resolution [80x24] 設置 L e g a c y 操作系統的行與欄的數量。設置值有:[80x24] [80x25] COM2 Console Redirection [Disabled] 開啟或關閉操作臺重定向。設置值有:[Disabled] [Enabled] Console Redirection Settings 請參閱在 COM1 下的【Console Redirection Settings】選項的內容。 華碩 P8B-C 系列主板用戶手冊 4-25
4.6 顯示器菜單(Monitor) 本菜單可顯示系統溫度或電源狀態并允許您改變風扇設置。 Main Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc. Event Logs Advanced Monitor Boot Tool Exit CPU Temperature(PECI) MB Temperature TR1 Temperature CPU FAN1 Speed FRNT FAN1 Speed FRNT FAN2 Speed FRNT FAN3 Speed REAR FAN1 Speed FAN Speed Control VCORE1 +3.3V +5V +12V VBAT +3VSB +1.5V [ +35ºC/ +94ºF] [ +35ºC/ +94ºF] [ N/A ] [ 1305 RPM] [ N/A ] [ N/A ] [ N/A ] [ N/A ] [Generic Mode] [ +1.200 V ] [ +3.360 V ] [ +5.
4.7 啟動菜單(Boot) 本菜單可讓您改變系統啟動設備與相關功能。請選擇下列選項並按下 <Enter> 鍵來顯示設置選項。 Main Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc. Event Logs Advanced Monitor Boot Tool Exit Setup Prompt Timeout Bootup NumLock State Full Screen Logo Option ROM Messages Interrupt 19 Capture EFI Boot Boot Device Seeking 5 [On] [Enabled] [Force BIOS] [Enabled] [Disabled] [Endless PXE] Boot Option Priorities Boot Option #1 [IBA GE Slot 0200 v...] Number of seconds to wait for setup activation key.
Interrupt 19 Capture [Enabled] 允許 Option ROM 阻止 interrupt 19。設置值有:[Disabled] [Enabled] EFI Boot [Disabled] 開啟或關閉 EFI Boot。設置值有:[Disabled] [Enabled] Boot Device Seeking [Endless PXE] [Endless PXE] 不 停 尋 找 遠 程 啟 動 圖 標 直 至 找 到 或 用 戶 停 止 ( 按 下 Ctrl+Alt+Del)。 [Normal] 僅尋找遠程啟動圖標一次然後停止。 Boot Option Priorities 本項讓您自行選擇啟動盤並排列開機備順序。屏幕上顯示的設備數量依 據系統中安裝的設備而定。 • 要選擇系統開機的啟動備,請在 A S U S 的圖標出現時按下 。 • 要以安全模式進入 Windows 操作系統,在開機自檢完成後, 按下 。 Boot Override 這些選項顯示可用設備。屏幕上顯示的設備數量依據系統中安裝的設備 而定。點擊一個選項開始啟動所選設備。 Network
4.8 工具菜單(Tools) 本工具菜單可以讓您針對特別功能進行設置。請選擇菜單中的選項並按下 鍵來顯示子菜單。 Main Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc. Event Logs Advanced Monitor Boot Tool Exit ASUS EZ Flash Utility Be used to update BIOS ASUS EZ Flash Utility 本項目可以讓您運行 ASUS EZ Flash。當您按下 <Enter> 鍵後,便會 有一個確認信息出現。請使用 左/右 方向鍵來選擇 [Yes] 或 [No],接著按 下 <Enter> 鍵來確認您的選擇。 4.9 退出 BIOS 程序(Exit) 本菜單可讓您保存或刪除您對 BIOS 選項的更改。 Main Aptio Setup Utility - Copyright (C) 2010 American Megatrends, Inc.
4-30 第四章:BIOS 程序設置
在本章節中,我們將介紹服務器內 所支持的磁盤陣列的設置與說明。 5 第五章:RAID 磁盤陣列設置
5 章節提綱 5.1 RAID 功能設置......................................................................................... 5-3 5.2 LSI 軟件 RAID 設置程序 (僅 P8B-C/4L)...................................... 5-5 5.3 Intel® Rapid Storage TechnologyOption ROM 工具程序.... 5-25 5.4 LSI Corporation MPT 設置程序 (僅 P8B-C/SAS/2L, P8B-C/SAS/4L).........................................
5.1 RAID 功能設置 本服務器主板支持以下 RAID 設置: 本主板可支持以下 SATA RAID 方案: • LSI MegaRAID 軟件 RAID 設置程序 (僅 P8B-C/4L ) 支持 RAID 0、 RAID 1 與 RAID 10(適用於 Linux 與 Windows)。 • Intel Rapid Storage 技術支持 RAID 0、RAID 1、RAID 10 與 RAID 5 (僅適用於 Windows)。 • LSI Corporation MPT 設置程序 (僅 P8B-C/SAS/2L, P8B-C/SAS/4L ) 支持 RAID 0, RAID 1, RAID 1E, 與 RAID 10。 5.1.
5.1.2 安裝硬盤 本主板支持 Serial ATA 硬盤。為了最佳的性能表現,當您要建立陣列模 式設置時,請盡可能採用具備相同型號與容量的硬盤。 請依照以下安裝方式來建構 SATA RAID 磁盤陣列: 1. 按照說明將 SATA 硬盤安裝至硬盤槽中。 2. 將 SATA 信號線連接到 SATA 硬盤背部的信號線接口。 3. 將 SATA 電源線連接到 SATA 硬盤背部的電源接口。 5.1.3 設置 BIOS 中的 RAID 選項 在您開始建立陣列之前,您必須先在 B I O S 程序設置中設置由芯片支持 SATA 接口的 RAID 選項。請依照下列步驟進行操作︰ 1. 在開機自檢(POST)過程中進入 BIOS 設置界面。 2. 進入主菜單(Main)後,選擇 SATA Configuration 選項,然後按 。 3. 將 Configuration SATA 項目設置為 [RAID]。 4. 按下<F10>保存您的設置值並退出 BIOS 程序。 關於如何在 BIOS 中針對菜單進行瀏覽與輸入,請參考第四章的 說明。 5.1.
5.2 LSI 軟件 RAID 設置程序 (僅 P8B-C/4L) LSI MegaRAID 軟件設置程序可以提供您創建 RAID 0、RAID 1 或 RAID 10 設置,通過主板上內置的南橋芯片所連接的 SATA 硬盤來創建。 請依照以下的步驟來進入 LSI MegaRAID 軟件設置程序: 1. 安裝所有 SATA 硬盤後啟動系統。 2. 在開機自檢過程中,LSI MegaRAID 軟件設置程序會自動偵測到安裝的 SATA 硬盤並顯示已存在的 RAID 磁盤陣列。按下 + 進入應 用程序。 LSI MegaRAID Software RAID BIOS Version A.
菜單 Configure Initialize Objects Rebuild Check Consistency 說明 本選項提供您以簡易快速的方式或設置新的命令來創建 RAID 0,RAID 1 或 RAID 10 設置。這個選項也可以 讓您查看、增加或刪除 RAID 的設置,或是選擇啟動的 硬盤設備。 允許您初始化已創建 RAID 設置的虛擬磁盤。 允許您初始化邏輯磁盤或更改虛擬磁盤的參數。 允許您重建失效的磁盤 提供您檢查已創建 RAID 設置的虛擬磁盤的數據一致 性。 5.2.
2. 在“ARRAYSELECTION MENU”畫面中,顯示目前連接且可用的SATA 硬盤有多少部。選擇您要進行設置 RAID 的硬盤,然後按下空格鍵。當 選擇時,硬盤指示會從 READY 更改成 ONLIN A[X] - [Y],而 X 所代表 的是 Array 數字,且 Y 表示硬盤設備的數字代號。 LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010 BIOS Version A.10.09231523R Easy Configuration - ARRAY SELECTION MENU Management Menu Configure Initialize Objects Rebuild Check Consistency PORT # 0 ONLIN A00-00 1 ONLIN A00-01 2 READY 3 READY Port # 2 DISK 74.74GB HDS728080PLA380 05.
5. 再按 <F10> 鍵,出現虛擬硬盤信息,包括“Virtual Drive”菜單。 您可設置虛擬硬盤參數。 LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010 BIOS Virtual VersionDrive(s) A.10.09231523R Configured LD RAID Size #Stripes StripSzMENU Status Easy Configuration - ARRAY SELECTION Management 0 Menu 1 148.
8. 選擇“Virtual Drive”菜單中的 Units 項目,然後按下 。 9. 在菜單中將 virtual drive 大小設置為 units,然後按下 <Enter>。 LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010 BIOS Virtual VersionDrive(s) A.10.09231523R Configured LD RAID Size #Stripes StripSzMENU Status Easy Configuration - ARRAY SELECTION Management 0 Menu 1 148.
12. 完成對選定虛擬磁盤的設置後,從菜單中選擇【A c c e p t】,然後按下 <Enter> 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010 BIOS Virtual VersionDrive(s) A.10.09231523R Configured LD RAID Size #Stripes StripSzMENU Status Easy Configuration - ARRAY SELECTION Management 0 Menu 1 148.
使用 New Configuration 設置 當一個 RAID 設置已經存在了,使用 New Configuration 命令來 清除存在的 RAID 設置數據。若您不要刪除已存在的 RAID 設置, 使用 View/Add Configuration 選項來查看或創建其他的 RAID 設 置。 請依照以下的步驟,使用 New Configuration (增加設置)模式來創建 一個 RAID 設置: 1. 在“Management Menu”中,選擇【Configure】選項,使用方向鍵來 選擇【New Configuration】項目,然後按下 <Enter> 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010 BIOS Version A.10.
5.2.2 增加或查看一個 RAID 設置 您可以使用 View/Add Configuration 功能來增加一個新的 RAID 或者是 查看一個現存的 RAID 設置。 增加一個 RAID 設置 請依照以下的步驟,來增加一個 RAID 設置: 1. 在“Management Menu”中,選擇【Configure】選項,再選擇【View/ Add Configuration】項目,然後按下 <Enter> 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010 BIOS Version A.10.
5.2.3 將虛擬盤初始化 當您完成創建 RAID 設置時,您必須將虛擬磁盤做初始化。您可以通過 Management Menu 中的 Initialize 或 Objects 選項,來進行虛擬磁盤初始化 的動作。 使用 Initialize 命令設置 請依照以下的步驟,來使用 Initialize(初始化)功能: 1. 進入“M a n a g e m e n t M e n u”後,選擇【I n i t i alize】選項,然後按下 <Enter> 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010 BIOS Version A.10.09231523R Management Menu Configure Initialize Objects Rebuild Check Consistency Initialize VD(s) Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option 2.
3. 按下 鍵來初始化硬盤設備。此時出現詢問框,選擇 [Yes],然後 按下 <Enter>。 LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010 BIOS Version A.10.09231523R Management Menu Configure Initialize Objects Rebuild Check Consistency LD RAID 0 1 Virtual Drive(s) Configured Size #Stripes StripSz 148.580GB 2 Status 64 KB ONLINE Initialize? Yes No Virtual Drives Virtual Drive 0 Init Will Destroy Data On Selected VD(s) SPACE-(De)Select, F10-Initialize 初始化硬盤設備的動作,將會清除所有硬盤內的數據。 4.
使用 Objects 命令設置 請依照以下的步驟,來使用 Objects 功能: 1. 在“Management Menu”中,選擇【Objects】選項中的【Virtual Drive】,然後按下 <Enter> 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010 BIOS Version A.10.09231523R Objects Management Menu Adapter Configure Virtual Drive Initialize Physical Drive Objects Rebuild Check Consistency Change VD Parameters Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option 2.
3. 從彈出子菜單中選擇【Initialize】選項,然後按下 <Enter> 鍵開始進行 硬盤初始化。 LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010 BIOS Version A.10.09231523R Vitual Drive(1) Virtual Drive 0 Objects Management Menu Adapter Configure Virtual Drive Initialize Physical Drive Objects Vitual Drive(0) Rebuild Initialze Check Consistency Check Consistency View/Update Parameters Initilize VD Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option 4.
5.2.4 重新創建失效的硬盤 您可以採用手動的方式重新創建損壞的硬盤設備,通過使用主畫面中的 Rebuild 命令來達成。 請依照以下的步驟來重新創建失效的硬盤: 1. 進入“M a n a g e m e n t M e n u”後,選擇【R e b u i l d】選項,然後按下 <Enter> 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010 BIOS Version A.10.09231523R Management Menu Configure Initialize Objects Rebuild Check Consistency Rebuild PD(s) Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option 2.
3. 當選擇欲重新創建的硬盤之後並按下 鍵,所選擇的硬盤設備則會 顯示 RBLD 的指示。當出現對話框時,請按下 <Y> 來重新創建硬盤 設備。 LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010 BIOS Version A.10.09231523R REBUILD - PHYSICAL DRIVES SELECTION MENU Management Menu PORT # Configure 0 ONLIN A00-00 Initialize Objects 1 RBLD A00-01 Rebuild Check Consistency Rebuilding Of Drive Will Take A Few Minutes.
5.2.5 檢查硬盤數據的一致性 您可以檢查與核對所選擇硬盤設備裡的數據一致性的正確性。這個工具 程序自動檢測與或採自動檢測與正確的數據任何差異,選擇【Objects】> 【Adapter】選項來進行。 Check Consistency(一致性檢查)命令可用在包含 RAID 1 或 RAID 10 設置下的虛擬磁盤。 使用 Check Consistency 命令設置 請依照以下步驟,使用 Check Consistency 命令檢查數據的一致性: 1. 在“Management Menu”中,選擇【Check Consistency】選項,然後 按下 <Enter> 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010 BIOS Version A.10.
3. 當出現提示時,按下空格鍵來從“Consistency Check”的對話框中選擇 [Yes],然後按下 <Enter> 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010 BIOS Version A.10.09231523R Management Menu Configure Initialize Objects Rebuild Check Consistency LD 0 Virtual Drive(s) Configured RAID Size #Stripes StripSz 10 154494MB 4 64 KB Yes No Status ONLINE Consistency Check? Virtual Drives Virtual Drive 0 Select VD SPACE-(De)Select, F10-Check Consistency 這時會出現進行中的完成百分比畫面。 LSI Software RAID Configuration Utility Ver C.
使用 Objets 命令 請依照以下的步驟,使用 Objets 命令檢查數據的一致性: 1. 在“Management Menu”中,選擇“Objets”中的【Virtual Drive】選 項。 2. 使用方向鍵來選擇您所要檢查的虛擬磁盤,然後按 <Enter> 鍵。 3. 從子菜單中,選擇【Check Consistency】,然後按下 <Enter> 鍵。 4. 當出現對話框時,按下 [Yes] 來開始進行檢查硬盤。 5.
5.2.6 刪除一個 RAID 設置 您可以依照以下的步驟,來刪除一個 RAID 設置: 1. 在“M a n a g e m e n t M e n u”中,選擇【C o n f i g u r e】>【C l e a r Configuration】,然後按 <Enter> 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010 BIOS Version A.10.
5.2.7 從 RAID 設置中選擇啟動磁盤 在您要設置選擇啟動磁盤前,您必須已經創建好一個新的 RAID 設置。請 參考“5.2.1 創建 RAID 陣列”的說明。 您可以依照以下的步驟,來選擇啟動磁盤: 1. 進入“Management Menu”後選擇【Configure】>【Select Boot Drive】,然後按 <Enter> 鍵。 LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010 BIOS Version A.10.
5.2.8 開啟 WriteCache 您可以開啟 RAID 控制功能的 WriteCache 選項,來增加數據傳輸性能。 當您開啟 WriteCache 功能時,您可能會在當一個電源間歇發生 在硬盤間傳輸或交換過程時,遺失文件。 設置 RAID 1 與 RAID 10 時建議使用 WriteCache 功能。 您可以依照以下的步驟,來啟用 WriteCache 功能: 1. 進入“Management Menu”後,選擇【Objects】>【Adapter】,然後 按下 <Enter> 鍵顯示改寫的特性。 2. 選擇【Disk WC】,然後按下 <Enter> 鍵來開啟選項。 LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010 BIOS Version A.10.
5.3 Intel® Rapid Storage Technology Option ROM 工具程序 Intel® Rapid Storage Technology Option ROM 工具程序通過南橋芯片的 支持,可讓您使用連接到主板上 Serial ATA 接口上的 Serial ATA 硬盤創建 RAID 0、RAID 1、RAID 10(RAID 1+0) 與 RAID 5 的陣列設置。 請依照以下步驟進入 Intel® Rapid Storage Technology Option ROM 應用 程序: 1. 安裝所有的 Serial ATA 硬盤。 2. 開啟系統。 3. 在開機自檢(POST)過程中,按下 + 進入程序主菜單。 Intel(R) Rapid Storage Technology - Option ROM - 10.1.0.1008 Copyright(C) 2003-10 Intel Corporation. All Rights Reserved. [ MAIN MENU ] 1. Create RAID Volume 2.
5.3.1 創建 RAID 陣列 請依照以下步驟創建 RAID: 1. 從程序主菜單中,選擇 1. Create RAID Volume,然後按下 。此 時將出現以下畫面。 Intel(R) Rapid Storage Technology - Option ROM - 10.1.0.1008 Copyright(C) 2003-10 Intel Corporation. All Rights Reserved. [ CREATE VOLUME MENU ] Name: RAID Level: Disks: Strip Size: Capacity: Sync: Volume0 RAID0(Stripe) Select Disks 128KB 0.0 GB N/A Create Volume [ HELP ] Enter a unique volume name that has no special characters and is 16 characters or less.
6. 使用向上、向下方向鍵來選擇 RAID 0 磁盤陣列要分割的容量(僅 RAID 0、RAID 10、RAID 5),然後按下 按鍵。分割的數值可 由 4KB 遞增至 128KB。數值為: RAID 0: 128KB RAID 10: 64KB RAID 5: 64KB 若此系統欲作為服務器使用,建議您選擇較低的磁區大小;若此 系統欲作為多媒體電腦用來運行影音的編輯製作,建議您選擇較 高的磁區大小來獲得最佳的性能。 7. 選擇 Capacity 項目,輸入您所要的陣列容量,接著按下 按鍵。 本項目默認值是採用最高可容許的磁盤容量。 8. 在 Create Volume 的提示對話框中再按下 按鍵來建立磁盤陣列, 接著便會出現如下圖的警示窗口畫面。 WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST. Are you sure you want to create this volume? (Y/N): 9.
2. 為您的修復磁區鍵入一個名稱,然後按下 <Enter> 按鍵。 3. 當 RAID Level 項目高亮時,按上/下鍵頭選擇 Recovery,然後按下 。 4. 當 Disk 選項高亮時,請按下 鍵以選擇要包含在修復設置中的硬 盤設備。接著如下圖所示的畫面便會出現。 [ SELECT DISKS ] Port 0 1 2 3 Drive Model ST3160812AS ST3160812AS ST3160812AS ST3160812AS Serial # 9LS0HJA4 9LS0F4HL 3LS0JYL8 9LS0BJ5H Size 149.0GB 149.0GB 149.0GB 149.0GB Status Non-RAID Non-RAID Non-RAID Non-RAID Disk Disk Disk Disk Select 1 Master and 1 Recovery disk to create volume.
5.3.3 刪除 RAID 磁區 在操作此功能時請務必非常小心,所有在硬盤中的數據將被一併 刪除。 請依照以下步驟刪除磁區: 1. 從程序主菜單中,選擇 2. Delete RAID Volume,然後按下 。此 時將出現以下畫面。 Intel(R) Rapid Storage Technology - Option ROM - 10.1.0.1008 Copyright(C) 2003-10 Intel Corporation. All Rights Reserved. [ DELETE VOLUME MENU ] Name Volume0 Level RAID0(Stripe) Drives 2 Capacity 298.0GB Status Normal Bootable Yes [ HELP ] Deleting a volume will reset the disks to non-RAID. WARNING: ALL DISK DATA WILL BE DELETED.
5.3.4 重新設置硬盤為非陣列硬盤 請注意!當您將 RAID 陣列硬盤設置為無 RAID 陣列狀態時,所 有磁盤陣列中的數據與陣列本身的結構數據都將被去除。 請依照以下步驟重新設置非陣列硬盤: 1. 從程序主菜單中,選擇 3. Reset Disks to Non-RAID,然後按下 。 此時將出現以下畫面。 [ RESET RAID DATA ] Resetting RAID disk will remove its RAID structures and revert it to a non-RAID disk. WARNING: Resetting a disk causes all data on the disk to be lost. (This does not apply to Recovery volumes) Port Drive Model Serial # Size Status 0 ST3160812AS 9LS0HJA4 149.0GB Member Disk 1 ST3160812AS 9LS0F4HL 149.
5.3.5 Recovery Volume 選項 若您創建了修復磁區,您可以進行更多修復。 請參考 5.3.2 創建修復磁區來建修復磁區。 請依照以下步驟設置修復磁區: 1. 從程序主菜單中,選擇 4. Recovery Volume Options 然後按下 。 此時將出現以下畫面。 Intel(R) Rapid Storage Technology - Option ROM - 10.1.0.1008 Copyright(C) 2003-10 Intel Corporation. All Rights Reserved. [ RECOVERY VOLUME OPTIONS ] 1. 2. Enable Only Recovery Disk Enable Only Master Disk [ HELP ] Enable Only Recovery Disk - enables recovery disk if available and disables master disk.
5.3.6 退出 Intel® Rapid Storage Technology 請依照以下步驟退出程序: 1. 從程序主菜單中,選擇 5. Exit 然後按下 。此時將出現以下畫 面。 [ CONFIRM EXIT ] Are you sure you want to exit? (Y/N): 2. 按下 退出,或按下 回到程序主菜單。 5.3.7 重建 RAID 本選項僅適用於 RAID 1 陣列。 使用未設置 RAID 的硬盤重建 RAID 陣列 若任何包含 RAID 1 陣列的 SATA 硬盤失敗,系統在 POST 過程中顯示 RAID volume 的狀態為“Degraded”。您可使用其他沒有設置 RAID 的硬盤 重建 RAID 陣列。 請依照以下步驟使用未設置 RAID 的硬盤重建 RAID 陣列: 1. 提示出現時,按下 + 進入 Intel Rapid Storage Technology 工具 程序。 2.
3. 選擇硬盤後程序自動開始重建。RAID volume 的狀態變為“Rebuild”。 Intel(R) Rapid Storage Technology - Option ROM - 10.1.0.1008 Copyright(C) 2003-10 Intel Corporation. All Rights Reserved. [ MAIN MENU ] 1. Create RAID Volume 2. Delete RAID Volume 5. Exit 3. Reset Disks to Non-RAID 4.
5.3.8 設置 BIOS 設置程序中的啟動陣列 當使用 Intel® Rapid Storage Technology 創建 multi-RAID 時,您可以為 RAID 陣列設置 BIOS 中的啟動優先級。 請依據以下步驟設置啟動陣列: 請設置至少一個啟動陣列。 1. 重啟系統並在 POST 過程中按下 進入 BIOS。 2. 點擊 Boot 菜單,選擇 Boot Device Priority 項目。 3. 使用上/下方向鍵選擇啟動優先級,然後按下 。更多信息請參 考“ 4.7.1 啟動設備順序 ”。 4. 在 Exit 菜單中選擇 Save Changes & Exit,然後按下 。 5.
5.
5.4.1 RAID 1 磁盤陣列 RAID 1 功能支持同時由兩塊硬盤購成鏡像磁盤陣列。 RAID 1 功能支持熱插拔,所以,當一組 RAID 1 磁盤陣列的硬盤失效時, 您可以輕鬆恢復磁盤陣列,而插拔後的硬盤會自動重新鏡像。 請依照以下步驟創建一個 RAID 1 磁盤陣列: 1. 安裝完 SAS 硬盤後啟動系統。 2. 在 POST過程中,請按下 進入 SAS 設置程序。 LSI Corporation MPT SAS2 BIOS MPT2BIOS-7.05.01.00 (2010.04.30) Copyright 2000-2010 LSI Corporation. Press Ctrl-C to start LSI Corp Configuration Utility... 為防止數據丟失,創建過程中請不要關閉系統。 3. 以下畫面出現。選擇一個通道並按下 來進入設置程序。 LSI Corp Config Utility Adapter List Global Properties v7.07.00.00 (2010.04.
4. Adapter Properties 畫面出現。 使用方向鍵選擇 RAID Properties,然後按下 。 LSI Corp Config Utility Adapter Properties -- SAS2008 v7.07.00.00 (2010.04.30) Adapter PCI Slot PCI Address(Bus/Dev) MPT Firmware Revision SAS Address NVDATA Version Status Boot Order Boot Support RAID Properties SAS Topology Advanced Adapter Properties Esc = Exit Menu Enter = Select Item SAS 2008 00 01:00 8.00.00.00-IR 500E0180:00010424 07.
6. Create New Volume 畫面顯示了您可以添加以構成 RAID 1 磁盤陣列的硬 盤。使用方向鍵選擇一塊硬盤,然後移動光標到 RAID Disk 列。要將此硬 盤包含在陣列中,請按下 <+>、<-> 或空格鍵。 LSI Corp Config Utility Create New Volume -- SAS2008 v7.07.00.00 (2010.04.
5.4.2 RAID 1E/10 磁盤陣列 RAID 1E/10 支持三至十塊硬盤,或七塊鏡像盤加兩塊 hot spare 盤。 使用奇數個硬盤創建 RAID 1E。使用偶數個硬盤創建 RAID 10。 請依照以下步驟創建 RAID1E/10 磁盤陣列: 1. 依照“RAID 1 磁盤陣列”部分的步驟 1–4 操作。 2. Select New Volume Type 畫面出現。 使用方向鍵選擇 Create RAID1E/10 Volume,然後按下 。 LSI Corp Config Utility v7.07.00.00 (2010.04.30) Select New Volume Type -- SAS2008 Create RAID 1 Volume Create a RAID 1 volume consisting of 2 disks plus up to 2 optional hot spares.
LSI Corp Config Utility Create New Volume -- SAS2008 v7.07.00.00 (2010.04.
5.4.3 RAID 0 磁盤陣列 RAID 0 功能提供支持二至十塊硬盤組成的 RAID 0 磁盤陣列。您可以用一 個 RAID 1 或 RAID 1E/10 磁盤陣列來創建一組 RAID 0 磁盤陣列。 請依照以下步驟創建 RAID 0 磁盤陣列: 1. 依照“RAID 1 磁盤陣列”部分的步驟 1–4 操作。 2. Select New Volume Type 畫面出現。 使用方向鍵選擇 Create RAID 0 Volume,然後按下 。 LSI Corp Config Utility v7.07.00.00 (2010.04.30) Select New Volume Type -- SAS2008 Create RAID 1 Volume Create a RAID 1 volume consisting of 2 disks plus up to 2 optional hot spares.
默認情況下,在陣列創建之前,RAID Disk 欄位顯示為 No。在 以下几種情況下,此欄位為灰色無法設置: • 硬盤不符合 RAID 陣列的最低要求。 • 硬盤容量較小,無法鏡像第一塊硬盤中的已有數據。 • 硬盤已是另一陣列的一部分。 4. 重複步驟 3 添加其他硬盤到磁盤陣列。 5. 完成後,按下 創建陣列,然後選擇 Save changes then exit this menu。 Create and save new volume? Cancel Exit Save changes then exit this menu Discard changes then exit this menu Exit the Configuration Utility and Reboot 6. 工具程序開始創建陣列。 LSI Corp Config Utility v7.07.00.00 (2010.04.30) Processing...may take up to 1 minute Creating RAID Volume...
5.4.4 管理陣列 LSI Corporation MPT 設置工具程序可讓您完成設置與管理 RAID 磁盤陣 列相關的其他任務。 請參考本章節查看磁盤陣列屬性,管理 hot spare 硬盤,同步陣列,激活 陣列與刪除陣列。 查看磁盤陣列屬性 請依照以下步驟查看磁盤陣列屬性: 1. 在主菜單上,點擊 RAID Properties。 LSI Corp Config Utility Adapter Properties -- SAS2008 v7.07.00.00 (2010.04.
3. View Volume 畫面出現。這裡您可以查看已創建的 RAID 陣列的屬性。 若您設置了 hot spare,它也將被列出。若您創建了不止一組陣列,您 可以按下 查看下一組陣列。 LSI Corp Config Utility View Volume -- SAS2008 Volume Identifier Type Size(GB) Status Task v7.07.00.00 (2010.04.
管理 hot spare 硬盤 您可以設置一塊硬盤作為 global hot spare 來保護 RAID 1/1E/10 磁盤陣列 中的重要數據。您可以在創建 RAID 1/1E/10 磁盤陣列的同時創建 hot spare 硬盤。當您需要在已有的磁盤陣列中添加 hot spare 硬盤時,請參考本章節 的說明。 若 RAID 1/1E/10 磁盤陣列中的一塊硬盤失效,工具程序會自動將 失效硬盤中的數據重新創建到 hot spare 硬盤中。當失效硬盤被 替換,工具程序將指定新加入的硬盤為新的 hot spare 硬盤。 請依照以下步驟創建 hot spare 硬盤: 1. 依照“查看磁盤陣列屬性”部分的步驟 1–3 操作。 2. 在 View Volume 畫面,選擇 Manage Volume,然後按下 。 LSI Corp Config Utility View Volume -- SAS2008 Volume Identifier Type Size(GB) Status Task v7.07.00.00 (2010.04.
4. 使用方向鍵選擇您想要設置為 hot spare 的硬盤,然後將光標移至 Hot Spr 列,按下 <+>, <-> 或空格鍵。 按下 確認更改,然後選擇 Save changes then exit this menu。 Drive Status 列將顯示 Hot Spare。 LSI Corp Config Utility View Volume -- SAS2008 Volume Identifier Type Size(GB) Status Task v7.07.00.00 (2010.04.
激活陣列 若一個陣列從一個控制器/電腦中刪除或移到另一控制器/電腦,陣列即被 認為是未激活狀態。當您要將陣列重新添加至系統時,您可以重新激活這個 陣列。 請依照以下步驟激活陣列: 1. 在 Manage Volume 畫面,選擇 Activate Volume,然後按下 。 LSI Corp Config Utility Manage Volume -- SAS2008 Identifier Type Size(GB) Status Task v7.07.00.00 (2010.04.30) LSI Logical Volume 3000 RAID 1 148 Inactive None Manage Hot Spares Consistency Check Activate Volume Delete Volume Online Capacity Expansion Esc = Exit Menu Enter = Select Item F1/Shift+1 = Help 2.
刪除陣列 • 若您刪除了一個陣列,您將無法恢復丟失的數據。在刪除陣 列之前,請確保您已備份了重要數據。 • 若您刪除了一個 RAID 1 磁盤陣列,第一塊硬盤中的數據將 被保留。 請依照以下步驟刪除陣列: 1. 在 Manage Volume 畫面,選擇 Delete Volume,然後按下 。 LSI Corp Config Utility Manage Volume -- SAS2008 Identifier Type Size(GB) Status Task v7.07.00.00 (2010.04.30) LSI Logical Volume 3000 RAID 1 148 Optimal None Manage Hot Spares Consistency Check Activate Volume Delete Volume Online Capacity Expansion Esc = Exit Menu Enter = Select Item F1/Shift+1 = Help 2.
擴大磁盤陣列容量 您可以使用兩塊新硬盤來代替已存在的一塊,擴大 RAID 磁盤陣列容量。 • 在擴大磁盤陣列容量之前,請先完成已存在的 RAID 磁盤陣 列的後台初始化。 • 新硬盤的容量需比已存在的硬盤大 50GB。 • 僅當 RAID 1 磁盤陣列處於最佳狀態(Optimal)時,此功能 才有用。 依據以下步驟擴展當前 RAID 磁盤陣列的容量: 1. 在 Manage Volume 畫面中,選擇 Online Capacity Expansion,然後按 下 。 LSI Corp Config Utility Manage Volume -- SAS2008 Identifier Type Size(GB) Status Task v7.07.00.00 (2010.04.
5.4.5 查看 SAS 拓樸 1. 在 Adapter Properties 畫面,選擇 SAS Topology,按下 <Enter>。 LSI Corp Config Utility Adapter Properties -- SAS2008 v7.07.00.00 (2010.04.30) Adapter PCI Slot PCI Address(Bus/Dev) MPT Firmware Revision SAS Address NVDATA Version Status Boot Order Boot Support RAID Properties SAS Topology Advanced Adapter Properties Esc = Exit Menu Enter = Select Item SAS 2008 00 01:00 8.00.00.00-IR 500E0180:00010424 07.
5.4.6 一般屬性(Global Properties) 在 Adapter List 畫面,按下 進入 Global Properties 菜單。在這 個菜單中您可以更改相關設置。 LSI Corp Config Utility Adapter List Global Properties Adapter SAS 2008 PCI BUS 01 PCI Dev 00 v7.07.00.00 (2010.04.30) PCI Fnc 00 PCI Slot 00 FW Revision Status 8.00.00.
Boot Information Display Mode 設置硬盤信息顯示模式。設置值有:[Display adapters & installed devices] [Display adapters only] [Display adapters and all devices] [Display minimal information] LSI Corp Config Utility Adapter List Global Properties v7.07.00.00 (2010.04.
Restore Defaults 本選項可讓您放棄您所做的選擇並恢復系統默認設置。 LSI Corp Config Utility Adapter List Global Properties v7.07.00.00 (2010.04.
5-54 第五章:RAID 磁盤陣列設置
在本章節中,我們將介紹主板所支持 的相關驅動程序的安裝與設置說明。 6 第六章:安裝 驅動程序
6 章節提綱 6.1 安裝 RAID 驅動程序.............................................................................. 6-3 6.2 安裝 Intel 芯片組軟件......................................................................... 6-15 6.3 安裝網卡驅動程序................................................................................ 6-17 6.4 安裝顯卡驅動程序................................................................................ 6-20 6.5 安裝管理應用與工具程序..................................................................
6.1 安裝 RAID 驅動程序 當您在系統中創建好 RAID 陣列模式後,現在您就可以開始安裝操作系統 至獨立的硬盤設備或具開機功能的磁盤陣列。這章節將來介紹在安裝操作系 統的過程中如何安裝 RAID 控制器的驅動。 6.1.1 創建一張 RAID 驅動程序軟盤 本系統不含軟驅。當您創建 RAID 驅動程序軟盤時需要使用軟驅。 若您使用 LSI 軟件 RAID 設置程序創建 RAID 陣列,您必須手動 調節 SATA 光驅的啟動順序。否則,系統將不會從連接的 SATA 光驅中啟動。 當您在進行 Windows® 或 Red Hat® Enterprise 操作系統安裝時,必須使 用一張 RAID 驅動程序軟盤,來指定所使用的陣列模式。您可以在 DOS 模 式下,創建 RAID 驅動程序軟盤(使用應用程序光盤中的 Makedisk 工具程 序進行製作)。 在 DOS 環境下,創建一張含有 RAID 驅動程序的軟盤: 1. 在光驅中放入本主板的驅動程序及應用程序光盤。 2. 重新開啟電腦,然後進入 BIOS 設置畫面。 3.
LSI 2008 SAS2 驅動程序 C20x LSI RAID Driver Windows XP 32 bit Windows XP 64 bit Windows Server 2003 32 bit Windows Server 2003 64 bit Windows Vista 32 bit Windows Vista 64 bit Windows Server 2008 32 bit Windows Server 2008 64 bit Windows 7 32 bit Windows 7 64 bit Windows Server 2008 R2 64 bit RHEL 4 UP7 32 bit RHEL 4 UP7 64 bit RHEL 4 UP8 32 bit RHEL 4 UP8 64 bit Back Exit 6. 找到 RAID 驅動程序並將一張高密度空白軟盤放入軟驅。 7. 按下 。 8.
在 Windows® 中創建 RAID 驅動程序軟盤: 1. 打開 Windows 操作系統。 2. 將主板應用程序光盤放入光驅。 3. 進入“Make Disk”菜單,選擇想要創建的 RAID 驅動程序軟盤的類型。 4. 將軟盤插入軟驅。 5. 按照屏幕指示完成操作。 寫入保護軟驅免受電腦病毒的侵害。 在 Red Hat® Enterprise Linux 服務器中創建 RAID 驅動程序軟盤: 1. 將一張空白格式化的高密度軟盤插入 USB 軟驅中。 2. 輸入 dd if=XXX.img of=/dev/fd0 在驅動程序與應用程序光盤中, 由以下路徑將文件減壓縮至軟盤: LSI MegaRAID 驅動程序: \Drivers\C20x LSI RAID\Driver\makedisk\Linux 3.
6.1.2 安裝 RAID 控制器驅動程序 在 Windows® Server 2008 操作系統安裝過程中 請依照以下步驟在 Windows ® Server 2008 操作系統安裝過程中安裝 RAID 控制器驅動程序: 1. 用 Windows® 服務器操作系統安裝光盤啟動系統。依據屏幕指示完成安 裝。 2. 在安裝類型中選擇“Custom(Advanced)”。 3.
4. 出現一條信息,提示您插入包含 RAID 控制器驅動程序的安裝媒體。若您 的系統中只有光驅,先退出 Windows 操作系統安裝盤,然後放入主板驅 動程序與應用程序光盤,點擊 Browse 繼續。 5. 找到光盤中的驅動程序,點擊 OK 繼續。 6. 從列表中選擇您需要的 RAID 控制器驅動程序,點擊 Next。 7. 當系統加載完成 RAID 驅動程序後,將驅動程序與應用程序光盤拿出,重 新放入操作系統安裝盤。選擇安裝系統的磁盤,點擊 Next。 8.
Red Hat® Enterprise Linux 5.0 操作系統 在 Red Hat® Enterprise 操作系統安裝時安裝 RAID 控制器驅動程序: 1. 使用 Red Hat® 操作系統安裝光盤啟動系統。 2. 在【Boot:】後輸入 linux dd noprobe=ata1 noprobe=ata2..., 然後按下 鍵。 - To install or upgrade in graphical mode, press the key. - To install or upgrade in text mode, type: linux text . - Use the function keys listed below for more information.
6. 選擇【No】並按下 鍵繼續。 More Driver Disks? Do you wish to load any more driver disks? Yes No 7. 按照屏幕提示完成 RedHat 操作系統安裝。 8. 安裝完成後,請勿點擊重新啟動。按下 + + 切換命令 行界面至圖形用戶界面。 9. 若使用 Legacy 軟驅,輸入以下指令: mkdir /mnt/driver mount /dev/fd0 /mnt/driver cd /mnt/driver sh replace_ahci.
SUSE Linux 11 操作系統 請依照以下的步驟,在 SUSE Linux Enterprise Server 操作系統安裝過程 中安裝 RAID 驅動程序: 1. 使用 SUSE 操作系統安裝光盤啟動系統。 2. 在【Boot Options】(啟動選項)菜單中,用方向鍵選擇【Installation】 (安裝)。 Boot from Hard Disk Installation Repair Installed System Rescue System Check Installation Media Firmware Test Memory Test Boot Options | F1 Help F2 Language F3 Video Mode English(US) 1024 X768 F4 Source DVD F5 Kernel F6 Driver Default No 3.
4. 將 RAID 驅動程序軟盤放入軟驅。 在 【Boot Options】(啟動選項) 後輸 入命令行:acpi=off apic=bigsmp brokenmodules=ahci,然後按下 鍵。 Boot from Hard Disk Installation Repair Installed System Rescue System Check Installation Media Firmware Test Memory Test Boot Options acpi=off apic=bigsmp brokenmodules=ahci F1 Help F2 Language F3 Video Mode English(US) 1024 X768 F4 Source DVD F5 Kernel F6 Driver Default Yes 5. 當以下畫面出現時,選擇【sda: USB Floppy】作為驅動程序升級媒介。 選擇【OK】,然後按下 鍵。 Please choose the Driver Update medium.
6. RAID 控制器驅動程序安裝到系統,如下圖所示。 Please choose the Driver Update medium. sda: USB Floppy sr0: CD-ROM, ASUS DRW-1612BLT sdb: Disk, LSI MEGA RAID sd3: Disk, LSI MEGA RAID Console other device OK Back 7.
6.2 安裝 Intel 芯片組軟件 本章節將介紹如何為系統中的 Intel® 芯片組安裝即插即用組件。 在 Windows 操作系統下,您需要手動安裝 Intel® 芯片組軟件。 1. 重新開機,使用 Administrator(管理員)權限登錄 Windows 系統。 2. 於光驅中放入主板/系統所附的應用程序與驅動程序光盤,若您的系統 已經啟動了光驅“自動播放”的功能,那麼稍後一會光盤會自動顯示 Drivers 菜單(驅動程序菜單)窗口。 若您的系統未啟動光驅“自動播放”的功能,請瀏覽光盤的文件 內容,找到 ASSETUP.EXE 文件,並雙擊 ASSETUP.EXE啟動光 盤。 4.
5. 選擇【Yes】接受許可同意條款,並且繼續安裝進程。 6. 閱讀文檔的信息並且按下【Next】鍵繼續安裝。 7.
6.3 安裝網卡驅動程序 本章節將介紹如何在 Windows® 服務器操作系統中安裝 Intel® 千兆網絡 控制器驅動程序。 請依照以下的步驟安裝網卡控制驅動程序: 1. 重新開機,使用 Administrator(管理員)權限登錄 Windows 系統。 2. 於光驅中放入主板/系統所附的應用程序與驅動程序光盤,若您的系統 已經啟動了光驅“自動播放”的功能,那麼稍後一會光盤會自動顯示 Drivers 菜單(驅動程序菜單)窗口。 • Windows ® 會自動偵測 LAN 控制器並顯示窗口。點擊【取 消】關閉窗口。 • 若您的系統未啟動光驅“自動播放”的功能,請瀏覽光盤的 文件內容,在 BIN 文件夾內找到 ASSETUP.EXE 文件。雙擊 ASSETUP.EXE 打開光盤。 3.
4. 當 Intel(R) 網絡連接–InstallShield Wizard 窗口出現時,點擊【Next】。 5. 勾選“I accept the terms in the license agreement”,然後點擊 【Next】繼續。 6.
7. 按照畫面指示完成安裝。 8.
6.4 安裝顯卡驅動程序 6.4.1 安裝 XGI Volari Z9s 顯卡驅動程序 (R1.0x) 本章節將介紹如何安裝 XGI® Z9s 顯示驅動程序。 您需要在 Windows® 操作系統中手動安裝 XGI® Z9s 顯示驅動程序。 1. 重新開機,使用 Administrator(管理員)權限登錄 Windows 系統。 2. 於光驅中放入主板 / 系統所附的應用程序與驅動程序光盤,若您的系 統已經啟動了光驅“自動播放”的功能,那麼稍後一會光盤會自動顯示 Drivers 菜單(驅動程序菜單)窗口。 若您的系統未啟動光驅“自動播放”的功能,請瀏覽光盤的文件 內容,找到 AUTORUN.EXE 文件,並雙擊 AUTORUN.EXE 運行 隨機光盤。 3. 點擊【XGI VOLARI Z9s Display Driver】項目。 4.
5. 點擊【Next】開始安裝。 5.
6.4.2 安裝 ASPEED AST1100 顯卡驅動程序 (R2.0x) 本章節將介紹如何安裝 ASPEED AST1100 顯示驅動程序。 您需要在 Windows® 操作系統中手動安裝 ASPEED AST1100 顯示驅動 程序。 1. 重新開機,使用 Administrator(管理員)權限登錄 Windows 系統。 2. 於光驅中放入主板 / 系統所附的應用程序與驅動程序光盤,若您的系 統已經啟動了光驅“自動播放”的功能,那麼稍後一會光盤會自動顯示 Drivers 菜單(驅動程序菜單)窗口。 若您的系統未啟動光驅“自動播放”的功能,請瀏覽光盤的文件 內容,找到 AUTORUN.EXE 文件,並雙擊 AUTORUN.EXE 運 行隨機光盤。 3. 點擊【ASPEED AST1100 Display Driver】項目。 4.
5. 要讓系統更新顯卡驅動程序,依據以下步驟操作。完成後點擊【Next】。 a. 接受條款。Accept the terms in the license agreement. b. 輸入用戶名與組織。(選填) c. 選擇設置類型。 6. 點擊【Install】開始安裝。 7.
6.5 安裝管理應用與工具程序 在主板所附的應用程序與驅動程序光盤中,包含有驅動程序、管理應用程 序,以及一些工具程序,讓您可以搭配在主板上操作使用。 應用程序與驅動程序光盤中的聯系信息,可能會因為不定時的情 況而有所更動。請參考華碩網頁(www.asus.com.cn)上的信息 來升級至最新的聯系信息。 6.5.1 運行驅動程序與應用程序光盤 將此光盤放入系統的光驅中,然後光驅會自動顯示 Drivers 菜單(驅動程 序)畫面。(若您的系統已經啟動了光驅“自動播放”的功能。) 如果 Drivers 菜單並未自動出現,那麼您也可以應用程序與驅動 程序光盤中的 BIN 文件夾裡面直接點擊 ASSETUP.EXE 主程序 來開啟菜單窗口。 6.5.
6.5.3 工具軟件菜單 應用程序菜單提供了您目前 所需要的工具軟件。請點擊您 所需要的軟件,來進行安裝。 6.5.4 制作磁盤菜單 此菜單中的項目可讓您制作 Intel RAID 與 LSI MegaRAID 驅動磁盤。 6.5.
6-24 第六章:安裝驅動程序
本章包含安裝主板時可以參考的相 關信息。 A 附錄:相關信息
A 附錄提綱 A.1 P8B-C 架構圖...........................................................................................
A.1 P8B-C 系列架構圖 P8B-C/4L (R1.
P8B-C/4L (R2.
P8B-C/SAS/2L (R1.
P8B-C/SAS/2L (R2.
P8B-C/SAS/4L (R1.
P8B-C/SAS/4L (R2.