User's Manual
Table Of Contents
- P8H77-V LE 仕様一覧
- Chapter 1
- 製品の概 要
- Chapter 2
- UEFI BIOS設定
- 2.1 UEFI BIOS管理更新
- 2.2 UEFI BIOS Utility
- 2.3 メインメニュー
- 2.4 Ai Tweaker メニュー
- 2.4.1 Ai Overclock Tuner [Auto]
- 2.4.2 Memory Frequency [Auto]
- 2.4.3 iGPU Max. Frequency [xxx]
- 2.4.4 EPU Power Saving Mode [Disabled]
- 2.4.5 GPU Boost [OK]
- 2.4.6 DRAM Timing Control
- 2.4.7 CPU Power Management
- 2.4.8 DIGI+ VRM
- 2.4.9 CPU Voltage [Offset Mode]
- 2.4.10 iGPU Voltage [Offset Mode]
- 2.4.11 DRAM Voltage [Auto]
- 2.4.12 VCCSA Voltage [Auto]
- 2.4.13 PCH Voltage [Auto]
- 2.4.14 CPU PLL Voltage [Auto]
- 2.5 アドバンスドメニュー
- 2.6 モニターメニュー
- 2.7 ブートメニュー
- 2.7.1 Bootup NumLock State [On]
- 2.7.2 Full Screen Logo [Enabled]
- 2.7.3 Wait for ‘F1’ If Error [Enabled]
- 2.7.4 Fast Boot [Enabled]
- 2.7.5 Option ROM Messages [Force BIOS]
- 2.7.6 CSM Support [Enabled]
- 2.7.7 Setup Mode [EZ Mode]
- 2.7.8 UEFI/Legacy Boot [Enabled both UEFI and Legacy]
- 2.7.9 PCI ROM Priority [Legacy ROM]
- 2.7.10 Boot Option Priorities
- 2.8 ツールメニュー
- 2.9 終了メニュー
- 2.10 Intel® 2012 Desktop Responsiveness Technology 概要
- 付録
ASUS P8H77-V LE
A-1
付録
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
• This device may not cause harmful interference.
• This device must accept any interference received including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with manufacturer’s instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment o and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit dierent from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required
to assure compliance with FCC regulations. Changes or modications to this unit not
expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.
IC: Canadian Compliance Statement
Complies with the Canadian ICES-003 Class B specications. This device complies with RSS
210 of Industry Canada. This Class B device meets all the requirements of the Canadian
interference-causing equipment regulations.
This device complies with Industry Canada license exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
Cut appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Cet appareil est conforme aux normes CNR exemptes de licence d’Industrie Canada. Le
fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas provoquer d’interférences et
(2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer
un fonctionnement non souhaité de l’appareil.
ご注意