Motherboard P9D WS
E8141 First Edition May 2013 Copyright © 2013 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Notices ........................................................................................................................ vi Safety information...................................................................................................... vii About this guide........................................................................................................ viii P9D WS specifications summary...............................................................................
Contents Chapter 3: 3.1 3.2 3.3 3.4 3.5 3.6 BIOS setup program................................................................................... 3-2 3.2.1 3.2.2 Ai Tweaker menu......................................................................................... 3-9 Advanced menu........................................................................................ 3-24 3.6.1 CPU Configuration..................................................................... 3-25 3.6.3 SATA Configuration....
Contents 4.3.3 EPU.............................................................................................. 4-7 4.3.5 USB 3.0 Boost........................................................................... 4-10 4.3.4 4.3.6 4.3.7 4.3.8 4.3.9 4.3.10 4.3.11 Chapter 5: 5.1 Fan Xpert 2.................................................................................. 4-8 EZ Update.................................................................................. 4-11 Network iControl..................
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • • • • • • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This guide contains the following parts: • • • • • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports. Chapter 2: Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components.
Conventions used in this guide To ensure that you perform certain tasks properly, take note of the following symbols used throughout this manual. DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Instructions that you MUST follow to complete a task. NOTE: Tips and additional information to help you complete a task.
P9D WS specifications summary CPU LGA1150 socket for 4th Gen Intel® Core™ i3 processors LGA1150 socket for Intel® Xeon® E3-1200/ 12x5 v3 series processor Supports 22nm CPU * Supports Intel® Turbo Boost technology 2.0. ** Refer to www.asus.com for Intel® CPU support list. Chipset Intel® C226 Chipset Memory 4 x DIMMs, max. 32GB, DDR3 1600 / 1333 MHz, ECC non-ECC, un-buffered memory Dual-channel architecture Supports Intel® Extreme Memory Profile (XMP) **Refer to www.asus.
P9D WS specifications summary ASUS Unique Features Workstation Unique Features Back Panel I/O Ports BIOS features Manageability ASUS Power Design - 8+2 Phase Power Design ASUS EPU - EPU, EPU Switch ASUS Exclusive Features - USB 3.
P9D WS specifications summary Internal I/O connectors 1 x USB 3.0/2.0 connector supports additional 2 USB ports (19-pin) 2 x USB 2.0/1.1 connectors support additional 2 USB ports 1 x USB 2.0/1.
Chapter 1 Chapter 1: Product introduction 1.1 Welcome! Thank you for buying an ASUS® P9D WS motherboard! The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your motherboard package for the following items.
1.3 Special features 1.3.1 Product highlights Green ASUS Chapter 1 This motherboard complies with the European Union’s Energy-related Products (ErP) requirements, which requires products to meet certain energy efficiency criteria for energy consumption. This in in keeping with ASUS’ vision of creating environment-friendly and energy-efficient products to reduce a product’s carbon footprint and reduce its environmental impact.
Complete USB 3.0 Integration Chapter 1 This motherboard offers you the strategic USB 3.0 accessibility for both the front and rear panels, allowing you to experience the convenience of the latest plug & play connectivity solution at speed up to ten times faster than USB 2.0. GPU Boost GPU Boost accelerates the integrated GPU for extreme graphics performance, facilitates flexible frequency adjustments, and easily delivers stable system-level upgrades for every use.
Quick Gate Chapter 1 Quick Gate is a vertical USB connector on the motherboard that allows you to install USB devices directly without any messy cables and stops important data storage devices from breaking off unexpectedly. This revolutionary and unique design offers a convenient and safe way to install data and applications on your system. Diagnosis LED Diag. LED offers an intuitive way to locate the root problems in seconds.
ASUS Fanless Design—Heat-sink solution Chapter 1 The crystal-shaped heatsink features 0-dB thermal solution that offers users a noiseless PC environment. Not only the beautiful shape upgrades the visual enjoyment for motherboard users, but also the heatsink design lowers the temperature of the chipset and power phase area through high efficient heat-exchange.
ASUS CrashFree BIOS 3 ASUS CrashFree BIOS 3 allows you to restore a corrupted BIOS file from a USB storage device containing the BIOS file. Chapter 1 IEEE 1394a interface IEEE 1394a interface provides high speed digital interface for audio/video devices such as digital television, digital video camcorders, storage peripherals and other portable devices.
Chapter 2 Chapter 2: Hardware information 2.1 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity.
2.2 Motherboard overview 2.2.1 Motherboard layout Chapter 2 Refer to 2.2.8 Internal connectors and 2.3.10 Rear panel connection for more information about rear panel connectors and internal connectors.
Layout contents Connectors/Jumpers/Switches/Slots Page 2. LGA1150 CPU Socket 2-26 3. CPU, chassis, and power fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN1-4) 2-4 2-5 4. DDR3 DIMM slots 2-22 6. USB 3.0 connector (20-1 pin USB3_12) 2-20 5. MemOK! switch 7. ASUS Dr. POWER switch 8. Intel C226 Serial ATA 6.0 Gb/s connectors (7-pin SATA6G_1-6 [yellow]) ® 2-11 2-17 2-18 9. DirectKey button 2-13 11. System panel connector (20-8 pin PANEL) 2-15 10. Clear RTC RAM (3-pin CLRTC) 12.
2.2.2 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA1150 socket designed for the Intel® 4th Generation Core™ i3 desktop Processors and Intel® Xeon® E3-1200/ 12x5 v3 series Server/ Workstation Processors. Chapter 2 Ensure that all power cables are unplugged before installing the CPU. 2-4 • Ensure that all power cables are unplugged before installing the CPU. • Ensure that you install the correct CPU designed for LGA1150 only.
2.2.3 System memory The motherboard comes with four Double Data Rate 3 (DDR3) Dual Inline Memory Modules (DIMM) slots. Chapter 2 A DDR3 module is notched differently from a DDR or DDR2 module. DO NOT install a DDR or DDR2 memory module to the DDR3 slot.
Memory configurations You may install 1GB, 2GB, 4GB, 8GB unbuffered ECC or non‑ECC DDR3 DIMMs into the DIMM sockets depending on the installed CPU. • You may install varying memory sizes in Channel A and Channel B. The system maps the total size of the lower-sized channel for the dual-channel configuration. Any excess memory from the higher-sized channel is then mapped for single-channel operation. • According to Intel CPU spec, DIMM voltage below 1.5V is recommended to protect the CPU. The max.
P9D WS Motherboard Qualified Vendors Lists (QVL) DDR3 1600 MHz capability Vendors Part No. Size SS/ DS Chip Brand Chip NO.
P9D WS Motherboard Qualified Vendors Lists (QVL) DDR3 1600 MHz capability Vendors Part No. Size SS/ DS Chip Brand Chip NO. Timing Voltage DIMM socket support (Optional) G.SKILL F3-12800CL7D-8GBRH (XMP) 8GB ( 2x 4GB ) DS - - 7-8-7-24 1.
P9D WS Motherboard Qualified Vendors Lists (QVL) DDR3 1600 MHz capability Vendors Part No. Size SS/ DS Chip Brand Chip NO. Timing Voltage DIMM socket support (Optional) SanMax SMD-4G68NG-16KK 4GB DS ELPIDA J2108BDBG-GN-F - - Silicon Power SP004GBLTU160V02(XMP) 4GB DS S-POWER 20YT5NG 9-9-9-24 1.5 • • 4GB DS Hynix H5TC2G83BFRH9A 9-9-9-24 1.
P9D WS Motherboard Qualified Vendors Lists (QVL) DDR3 1333 MHz capability Vendors Part No. Size SS/ DS Chip Brand Chip NO. Timing Voltage DIMM socket support (Optional) G.SKILL F3-10666CL9D-8GBXL 8GB ( 2x 4GB ) DS - - 9-9-9-24 1.5 GEIL GG34GB1333C9DC 4GB ( 2x 2GB ) DS GEIL GL1L128M88BA115FW 9-9-9-24 1.
2.2.4 Expansion slots Chapter 2 Ensure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. Slot No. Slot Description 1 PCIe 3.0 x16_1 slot (single at x16 or dual at x8/x8 mode) 2 PCIe 2.0 x1_1 slot 3 PCIe 3.0 x16_2 slot (single at x8 or dual at x4/x4 mode) 4 PCI1 slot 5 PCIe 3.0 x16_3 slot (x4 mode) 6 PCI2 slot 7 PCIe 2.
Standard Interrupt assignments IRQ Priority Standard function 1 2 Keyboard Controller 0 2 4 5 6 7 8 9 Chapter 2 10 11 12 13 14 1 - 12 13 14 15 3 4 5 6 7 8 9 System Timer Programmable Interrupt Communications Port (COM1) IRQ Holder for PCI Steering Reserved Reserved System CMOS/Real Time Clock IRQ Holder for PCI Steering IRQ Holder for PCI Steering IRQ Holder for PCI Steering Reserved Numeric Data Processor Primary IDE Channel IRQ assignments for this motherboard PCIEx16_1 PCIEx16_2 PCIEx16_
2.2.5 Onboard buttons and switches Onboard buttons and switches enhance overclocking and gaming performance when working on a bare or open-case system. 1. EPU switch Turning this switch to Enable will automatically detect the current PC loadings and intelligently moderate the power consumption. Chapter 2 For ensuring the system performance, turn the switch setting to Enable when the system is powered off. 2. ASUS Dr. POWER switch This switch allows you to enable or disable the ASUS Dr.
3. DirectKey button This feature allows your system to go to the BIOS Setup program with the press of a button. With DirectKey, you can enter the BIOS anytime without having to press the key during POST. It also allows you to turn on or turn off your system and conveniently enter the BIOS during boot-up. Chapter 2 Ensure to save your data before using the DirectKey button. 2-14 • When the system is on and you press the DirectKey button, your system will shut down.
MemOK! button When you install DIMMs that are not compatible with the motherboard, this may cause the system boot failure, and the DIAG_DRAM near the MemOK switch lights continuously. Simply press the MemOK button until the DIAG_DRAM starts blinking to patch memory compatibility issues and ensure the system’s successful bootup. Chapter 2 4. • Refer to section 2.2.6 Onboard LEDs for the exact location of the DIAG_DRAM. • The DIAG_DRAM also lights when the DIMM is not properly installed.
2.2.6 1. Onboard LEDs POST State LEDs The POST State LEDs indicate the status of these key components during POST (Power-on-Self Test): CPU, memory modules, VGA card, and hard disk drive. If an error is found, the critical component’s LED stays lit up until the problem is solved. Chapter 2 2. 2-16 EPU LED The EPU LED lights up when the EPU switch is turned to Enable.
Standby power LED The motherboard comes with a standby power LED that lights up to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should shut down the system and unplug the power cable before removing or plugging in any motherboard component. The illustration below shows the location of the onboard LED. Chapter 2 3. 4. DIAG_DRAM The DIAG_DRAM lights up when the installed DIMMs incompatible with the motherboard or improperly installed.
5. PWR_SUPPLY LED The ASUS Dr. Power LED near EATX PWR connector lights up when the ASUS Dr. Power switch setting is turned to Enable and the power supply unit failed. Chapter 2 6. 2-18 PGLED3 LED The ASUS Dr. Power LED near the ASUS Dr. Power switch lights up when the ASUS Dr. Power switch is turned to enable.
+12V_PWR LED The ASUS Dr. Power LED near EATX12V connector lights up when the ASUS Dr. Power switch setting is turned to enable and there is no power detected going into the processor. Chapter 2 7. 8. CPU warning LED (CPU_PWR_ERR) The CPU warning LEDs light up to indicate an impending failure of the corresponding CPU.
9. DIMM warning LED (DRAM_PWR_ERR) The DIMM warning LEDs light up to indicate an impending failure of the corresponding DIMMs.
2.2.7 1. Jumper Clear RTC RAM (3-pin CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM 1. Turn OFF the computer and unplug the power cord. 3. Plug the power cord and turn ON the computer. 2.
2. Chapter 2 2-22 Chassis Fan control setting (3-pin CHAFAN_SEL) These jumpers allow you to switch for fan pin selection. The CHAFAN_SEL jumper is for the front fans and rear fans control. Set to pins 1–2 when using 3-pin fans or pins 2–3 when using 4-pin fans. • If you use a 4-pin fan but set the jumper to pin 1-2, the fan you installed may not work. • If you use a 3-pin fan but set the jumper for a 4-pin fan, the fan control will not work and the fan you installed will always run at full speed.
2.2.8 Intel® C226 Serial ATA 6.0 Gb/s connectors (7-pin SATA6G_1-6 [yellow]) These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA 6.0 Gb/s signal cables. Chapter 2 1. Internal connectors • These connectors are set to [AHCI Mode] by default. If you intend to create a Serial ATA RAID set using these connectors, set the SATA Mode item in the BIOS to [RAID Mode]. Refer to section 3.5.4 SATA Configuration for details. • Before creating a RAID set, refer to section 4.
2. USB 2.0 connectors (Type A: 10-1 pin USB910/ USB1112; Type B: USB13) These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed. Chapter 2 Never connect a 1394 cable to the USB connectors.
USB 3.0 connector (20-1 pin USB3_12) These connectors allow you to connect a USB 3.0 module for additional USB 3.0 front or rear panel ports. With an installed USB 3.0 module, you can enjoy all the benefits of USB 3.0 including faster data transfer speeds of up to 5Gbps, faster charging time for USB-chargeable devices, optimized power efficiency and backward compatibility with USB 2.0. Chapter 2 3. The USB 3.0 module is purchased separately. 4.
5. IEEE 1394a port connector (10-1 pin IE1394_1) This connector is for an IEEE 1394a port. Connect the IEEE 1394a module cable to this connector, then install the module to a slot opening at the back of the system chassis. Chapter 2 Never connect a USB cable to the IEEE 1394a connector. Doing so will damage the motherboard! The IEEE 1394a module is purchased separately. 6. Digital audio connector (4-1 pin SPDIF_OUT) This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port.
7. CPU, chassis, and power fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN1-4) Chapter 2 Connect the fan cables to the fan connectors on the motherboard, ensuring that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components.
8. Chapter 2 9. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector. • We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s high-definition audio capability.
10. TPM connector (20-1 pin TPM) Chapter 2 This connector supports a Trusted Platform Module (TPM) system, which can securely store keys, digital certificates, passwords, and data. A TPM system also helps enhance network security, protects digital identities, and ensures platform integrity. This connector can also serve for G.P. Diagnosis card installtion. G.P. Diagnosis card layout LED 0 and 1 Power Switch. Press to turn ON or OFF the motherboard. Reset Button. Press to restart the motherboard�.
Installing G.P. Diagnosis card Ensure to turn off the power supply unit before installing the diagnosis card to avoid electrical shock hazard. 1. 2. Locate the TPM connector (20-1 pin TPM) on the motherboard. With the LEDs of the diagnosis card facing to the PCIe slots, align the card connector with the TPM connector and press firmly until the card sits on the connector completely. Chapter 2 Code table for G.P.
Direct Connector (2-pin DRCT) This connector is for the chassis-mounted button that supports the DirectKey function. Connect the button cable that supports DirectKey, from the chassis to this connector on the motherboard. Chapter 2 11. Ensure that your chassis comes with the extra button cable that supports the DirectKey feature. Refer to the technical documentation that came with the chassis for details. 12.
13. Chapter 2 2-32 ATX power connectors (24-pin EATXPWR, 8-pin EATX12V) These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. • For a fully configured system, we recommend that you use a power supply unit (PSU) that complies with ATX 12 V Specification 2.0 (or later version) and provides a minimum power of 350 W.
14. System panel connector (20-8 pin PANEL) • • • • • Chapter 2 This connector supports several chassis-mounted functions. System power LED (2-pin PWR_LED) This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. Hard disk drive activity LED (2-pin HDD_LED) This 2-pin connector is for the HDD Activity LED.
2.3 Building your computer system 2.3.1 Additional tools and components to build a PC system Chapter 2 1 bag of screws Philips (cross) screwdriver PC chassis Power supply unit Intel LGA 1150 CPU Intel LGA 1150 compatible CPU Fan DIMM SATA hard disk drive SATA optical disc drive (optional) Graphics card (optional) The tools and components in the table above are not included in the motherboard package.
2.3.
4 Chapter 2 5 C A B 6 2-36 Chapter 2: Hardware information
2.3.3 CPU heatsink and fan assembly installation Apply the Thermal Interface Material to the CPU heatsink and CPU before you install the heatsink and fan if necessary.
To uninstall the CPU heatsink and fan assembly 1 Chapter 2 2 A B B A 2-38 Chapter 2: Hardware information
2.3.
2.3.5 Motherboard installation The diagrams in this section are for reference only. The motherboard layout may vary with models, but the installation steps remain the same.
Chapter 2 3 DO NOT overtighten the screws! Doing so can damage the motherboard.
2.3.
2.3.
2.3.8 Front I/O Connector To install ASUS Q-Connector 1 2 IDE_LED+ IDE_LED- PWR Ground Chapter 2 Reset Ground IDE_LED R POWE SW RESET SW To install USB 2.0 Connector To install front panel audio connector AAFP USB 2.0 To install USB 3.0 Connector USB 3.
2.3.
2.3.10 BIOS update utility USB BIOS Flashback USB BIOS Flashback allows you to easily update the BIOS without entering the existing BIOS or operating system. Simply insert a USB storage device to the USB port, press the USB BIOS Flashback button for three seconds, and the BIOS is updated automatically. To use USB BIOS Flashback: 1. 2. Place the bundled support DVD to the optical drive and install the USB BIOS Flashback Wizard. Follow the onscreen instructions to complete the installation.
Rear panel connection Chapter 2 2.3.11 Rear panel connectors 1. PS/2 mouse and keyboard port 7. ����������� DisplayPort 2. ����������������������� Optical S/PDIF Out port 8. ��������� HDMI port 3. LAN (RJ-45) port 2* 9. 4. DVI port 10. ������������������������� USB BIOS Flashback button 5. LAN (RJ-45) port 1* 11. USB 3.0 ports 3 and 4 6. USB 2.0 ports 7 and 8 12. Audio I/O ports** USB 2.
• Due to USB 3.0 controller limitation, USB 3.0 devices can only be used under Windows® OS environment and after the USB 3.0 driver installation. • USB 3.0 devices can only be used as data storage only. • We strongly recommend that you connect USB 3.0 devices to USB 3.0 ports for faster and better performance for your USB 3.0 devices.
Connect to Headphone and Mic Chapter 2 Connect to Stereo Speakers Connect to 2.1 channel Speakers Connect to 4.
Connect to 5.1 channel Speakers Chapter 2 Connect to 7.
2.4 Starting up for the first time 1. After making all the connections, replace the system case cover. 3. Connect the power cord to the power connector at the back of the system chassis. 2. 4. 5. Be sure that all switches are off. Connect the power cord to a power outlet that is equipped with a surge protector. Turn on the devices in the following order: a. Monitor c. System power b. 6.
Chapter 2 2-52 Chapter 2: Hardware information
Chapter 3 Chapter 3: BIOS setup 3.1 Knowing BIOS The new ASUS UEFI BIOS is a Unified Extensible Interface that complies with UEFI architecture, offering a user-friendly interface that goes beyond the traditional keyboardonly BIOS controls to enable a more flexible and convenient mouse input. You can easily navigate the new UEFI BIOS with the same smoothness as your operating system. The term “BIOS” in this user manual refers to “UEFI BIOS” unless otherwise specified.
3.2 BIOS setup program Use the BIOS Setup to update the BIOS or configure its parameters. The BIOS screen include navigation keys and brief onscreen help to guide you in using the BIOS Setup program. Entering BIOS at startup To enter BIOS Setup at startup: • Press during the Power-On Self Test (POST). If you do not press , POST continues with its routines. Entering BIOS Setup after POST To enter BIOS Setup after POST: • Press ++ simultaneously.
3.2.1 EZ Mode By default, the EZ Mode screen appears when you enter the BIOS setup program. The EZ Mode provides you an overview of the basic system information, and allows you to select the display language, system performance mode and boot device priority. To access the Advanced Mode, click Exit/Advanced Mode, then select Advanced Mode or press hot key for the advanced BIOS settings. The default screen for entering the BIOS setup program can be changed. Refer to the Setup Mode item in section 3.
3.2.2 Advanced Mode The Advanced Mode provides advanced options for experienced end-users to configure the BIOS settings. The figure below shows an example of the Advanced Mode. Refer to the following sections for the detailed configurations. To access the Advanced Mode, click Exit, then select Advanced Mode or press F7 hotkey.
Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting Main shows the Main menu items. The other items (Ai Tweaker, Advanced, Monitor, Boot, Tool, and Exit) on the menu bar have their respective menu items. Back button This button appears when entering a submenu. Press or use the USB mouse to click this button to return to the previous menu screen.
Last Modified button This button shows the items that you last modified and saved in BIOS Setup. 3.3 My Favorites MyFavorites is your personal space where you can easily save and access your favorite BIOS items. Chapter 3 Adding items to My Favorites To add frequently-used BIOS items to My Favorites: 1. Use the arrow keys to select an item that you want to add. When using a mouse, hover the pointer to the item. 2.
3.4 Main menu The Main menu screen appears when you enter the Advanced Mode of the BIOS Setup program. The Main menu provides you an overview of the basic system information, and allows you to set the system date, time, language, and security settings. Security Chapter 3 The Security menu items allow you to change the system security settings. • If you have forgotten your BIOS password, erase the CMOS Real Time Clock (RTC) RAM to clear the BIOS password. See section 1.2.
Administrator Password If you have set an administrator password, we recommend that you enter the administrator password for accessing the system. Otherwise, you might be able to see or change only selected fields in the BIOS setup program. To set an administrator password: 1. Select the Administrator Password item and press . 2. From the Create New Password box, key in a password, then press . 3. Confirm the password when prompted. To change an administrator password: 1.
To change a user password: 1. Select the User Password item and press . 2. From the Enter Current Password box, key in the current password, then press . 3. From the Create New Password box, key in a new password, then press . 4. Confirm the password when prompted. To clear the user password, follow the same steps as in changing a user password, but press when prompted to create/confirm the password.
Ai Overclock Tuner [Auto] Allows you to select the CPU overclocking options to achieve the desired CPU internal frequency. Select any of these preset overclocking configuration options: [Auto] [X.M.P.] Loads the optimal settings for the system. Allows your system to automatically optimize the CPU ratio, BCLK frequency, and memory parameters. If you install memory modules supporting the eXtreme Memory Profile (X.M.P.
4-Core Ratio Limit [Auto] Select [Auto] to apply the CPU default Turbo Ratio setting or manually assign a 4-Core Limit value that must be higher than or equal to the 3-Core Ratio Limit. If you assign a value for 4-Core Ratio Limit, do not set the 1-Core Ratio Limit, 2-Core Ratio Limit, and 3-Core Ratio to [Auto]. Min CPU Cache Ratio [Auto] Allows you to set the minimum possible ratio on the Uncore part of the processor. Use the <+> or <-> keys to adjust the value. The values depend on the CPU installed.
Primary Timings DRAM CAS# Latency [Auto] Configuration options: [Auto] [1] – [31] DRAM RAS# to CAS# Delay [Auto] Configuration options: [Auto] [1] – [31] DRAM RAS# PRE Time [Auto] Configuration options: [Auto] [1] – [31] DRAM RAS# ACT Time [Auto] Configuration options: [Auto] [1] – [63] DRAM Command Rate [Auto] Configuration options: [Auto] [1] – [3] Secondary Timings DRAM RAS# to RAS# Delay [Auto] Configuration options: [Auto] [1] – [15] DRAM REF Cycle Time [Auto] Configuration options: [Auto] [1] –
DRAM RTL (CHA_R1D0) [Auto] Configuration options: [Auto] [1] - [63] DRAM RTL (CHA_R1D1) [Auto] Configuration options: [Auto] [1] - [63] DRAM RTL (CHB_R0D0) [Auto] Configuration options: [Auto] [1] - [63] DRAM RTL (CHB_R0D1) [Auto] Configuration options: [Auto] [1] - [63] DRAM RTL (CHB_R1D0) [Auto] Configuration options: [Auto] [1] - [63] DRAM RTL (CHB_R1D1) [Auto] Configuration options: [Auto] [1] - [63] DRAM IO-L (CHA_R0D0) [Auto] Configuration options: [Auto] [1] - [15] DRAM IO-L (CHA_R0D1) [Auto]
tWRRD_dr [Auto] Configuration options: [Auto] [1] – [15] tWRRD_dd [Auto] Configuration options: [Auto] [1] – [15] tWRWR [Auto] Configuration options: [Auto] [1] – [7] tWRWR_dr [Auto] Configuration options: [Auto] [1] – [15] tWRWR_dd [Auto] Configuration options: [Auto] [1] – [15] Dec_WRD [Auto] Configuration options: [Auto] [0] – [1] tRDWR [Auto] Configuration options: [Auto] [1] – [31] tRDWR_dr [Auto] Configuration options: [Auto] [1] – [31] tRDWR_dd [Auto] Configuration options: [Auto] [1] – [31]
DIGI+ Power Control CPU Load-Line Calibration [Auto] Load-line is defined by Intel® VRM specification and affects CPU power voltage. The CPU working voltage will decrease proportionally to CPU loading. Higher load-line calibration could get higher voltage and good overclocking performance, but increases the CPU and VRM thermal conditions. Select from Level 1 to Level 8 to adjust CPU power voltage from 0% to 100%. The actual performance boost may vary depending on your CPU specification.
CPU Power Phase Control [Auto] Allows you to set the power phase control of the CPU. Configuration options: [Auto] [Standard] [Optimized] [Extreme] [Manual Adjustment] DO NOT remove the thermal module when setting this item to [Extreme] and [Manual Adjustment]. The thermal conditions should be monitored. The following item appears only when you set the CPU Power Phase Control to [Manual Adjustment].
DRAM Current Capability [100%] A higher value brings a wider total power range, and extends the overclocking range simultaneously. Configuration options: [100%] [110%] [120%] [130%] [140%] DRAM Voltage Frequency [Auto] Allows you to adjust the DRAM switching frequency. Assign a fixed high DRAM frequency to increase the O.C. range, or a low DRAM frequency for a better system stability.
Turbo Mode Parameters Long Duration Package Power Limit [Auto] Allows you to limit the Turbo Ratio’s time duration that exceeds the TDP (Thermal Design Power) for maximum performance. Use the <+> or <-> keys to adjust the value. The values range from 1W t0 4096W. Package Power Time Window [Auto] Also known as Power Limit 1, and allows you to maintain the time window for Turbo Ratio over TDP (Thermal Design Power). Use the <+> or <-> keys to adjust the value. The values range from 1 to 127 in seconds.
Power Decay Mode [Auto] Allows your system to improve the power saving mode on the Fully Integrated Voltage Regulator as the processor goes into low current state. Configuration options: [Auto] [Disabled] [Enabled] Idle Power-in Response [Auto] Allows you to set the slew rate for the Fully Integrated Voltage Regulator as it enters manual override mode.
CPU Core Voltage [Auto] Allows you to configure the amount of voltage fed to the cores of the processor. Increase the amount of voltage when increasing core frequency. Configuration options: [Auto] [Manual Mode] [Offset Mode] [Adaptive Mode] • The Adaptive Mode option appears only if you are using an Intel® Core™ i3 series processors. • The following item appears only when you set the CPU Core Voltage to [Manual]. CPU Core Voltage Override [Auto] Allows you to set the CPU Core Voltage override.
Offset Mode Sign [+] [+] To offset the voltage by a positive value. [–] To offset the voltage by a negative value. CPU Cache Voltage Offset Allows you to set the CPU cache voltage offset. Use the <+> or <-> keys to adjust the value. The values range from 0.001V to 0.999V with a 0.001V interval. CPU Graphics Voltage [Auto] Allows you to configure the amount of voltage fed to the onboard graphics unit on the processor. Increase the amount of voltage when increasing iGPU frequency.
CPU System Agent Voltage Offset Mode Sign [+] [+] [–] To offset the voltage by a positive value. To offset the voltage by a negative value. CPU System Agent Voltage Offset [Auto] Allows you to configure the amount of voltage fed to the system agent of the processor including its PCIe controller and power control unit. Increase the amount of voltage when increasing DRAM frequency. Use the <+> or <-> keys to adjust the value. The values range from 0.001V to 0.999V with a 0.001V interval.
DRAM DATA REF Voltage on CHA [Auto] This item is the DRAM reference voltage for the data lines on Channels A and B. You can use the <+> or <-> keys to adjust the value. The values range from 0.395x to 0.630x with a 0.005x interval. DRAM DATA REF Voltage on CHB [Auto] This item is the DRAM reference voltage for the data lines on Channels A and B. You can use the <+> or <-> keys to adjust the value. The values range from 0.395x to 0.630x with a 0.005x interval.
3.6 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Be cautious when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction.
3.6.1 CPU Configuration The items in this menu show the CPU-related information that the BIOS automatically detects. Chapter 3 The items in this menu may vary based on the CPU installed. Intel Adaptive Thermal Monitor [Enabled] [Enabled] [Disabled] Enables the overheated CPU to throttle its clock speed to cool down. Disables the CPU thermal monitor function.
Active Processor Cores [All] Allows you to choose the number of CPU cores to activate in each processor package. Configuration options: [All] [1] [2] [3] Limit CPUID Maximum [Disabled] [Enabled] [Disabled] Allows legacy operating systems to boot even without support for CPUs with extended CPUID functions. Disables this function. Execute Disable Bit [Enabled] [Enabled] [Disabled] Enables the No-Execution Page Protection Technology. Forces the XD feature flag to always return to zero (0).
Turbo Mode [Enabled] Allows you to set the processor cores to run faster than the base frequency when operating below power, current and temperature specification limit. Configuration options: [Enabled] [Disabled] CPU C States [Auto] Allows you to enable or disable the CPU C states. Configuration options: [Auto] [Enabled] [Disabled] The following items appear only when you set the CPU C States to [Enabled]. Enhanced C1 state [Enabled] Allows your processor to reduce power when the system is in idle mode.
3.6.2 PCH Configuration PCI Express Configuration Allows you to configure the PCI Express slots. DMI Link ASPM Control [Auto] Allows you to control the ASPM (Active State Power Management) on both Northbridge side and Southbridge side of the DMI Link. Configuration options: [Disabled] [Enabled] [Auto] ASPM Support [Disabled] Allows you to set the ASPM level. Configuration options: [Disabled] [Auto] [L0s] [L1] [L0sL1] PCIe Speed [Auto] Allows you to select the PCI Express port speed.
Active Memory Threshold [0] Key in the value for the additional partition size for Rapid Start Technology to work. Ensure that the caching partition size is larger than the total memory size. Hybrid Hard Disk Support [Disabled] Allows you to enable or disable the hybrid hard disk support. Configuration options: [Enabled] [Disabled] Intel Smart Connect Technology [Disabled] Allow you to enable or disable the Intel® Smart Connect Technology. Configuration options: [Enabled] [Disabled] 3.6.
SATA Mode Selection [AHCI] Allows you to set the SATA configuration. [Disabled] [IDE] [AHCI] [RAID] Disables the SATA function. Set to [IDE Mode] when you want to use the Serial ATA hard disk drives as Parallel ATA physical storage devices. Set to [AHCI Mode] when you want the SATA hard disk drives to use the AHCI (Advanced Host Controller Interface).
3.6.4 System Agent Configuration VT-d [Disabled] Allows you to enable virtualization technology function on memory control hub. [Enabled] Enables the function. [Disabled] Disables this function. This item will appear only if the CPU supports virtualization technology function. CPU Audio Devices [Enabled] Allows you to enable or disable CPU SA Audio devices. Configuration options: [Enabled] [Disabled] Chapter 3 DVI Port Audio [Enabled] Allows you to enable or disable DVI port Audio.
NB PCIe Configuration Allows you to configure the NB PCI Express settings. PCIEx16_1/2/3 Link Speed [Auto] Allows you to configure the PCIEx16 speed. Configuration options: [Auto] [Gen1] [Gen2] [Gen3] DMI Link ASPM Control [Auto] Allows you to enable or disable the control of Active State Power Management on SA side of the DMI Link. Configuration options: [Auto] [Disabled] [L0s] [L1] [L0sL1] PEG - ASPM [Disabled] Allows you to control ASPM support for the PEG device.
3.6.5 USB Configuration The items in this menu allow you to change the USB-related features. The USB Devices item shows the auto-detected values. If no USB device is detected, the item shows None. Legacy USB Support [Enabled] [Enabled] Enables the support for USB devices on legacy operating systems (OS). [Disabled] The USB devices can be used only for the BIOS setup program. It cannot be recognized in boot devices list. Allows the system to detect the presence of USB devices at startup.
3.6.6 Platform Misc Configuration The items in this menu allow you to configure the platform-related features. PCI Express Native Power Management [Disabled] Allows you to enhance the power saving feature of PCI Express and perform ASPM operations in the operating system. Configuration options: [Disabled] [Enabled] The following item appears only when you set the PCI Express Native Power Management to [Enabled].
3.6.7 Onboard Devices Configuration Scroll down to view the other BIOS items. HD Audio Controller [Enabled] [Enabled] Enables the High Definition Audio Controller. [Disabled] Disables the controller. Chapter 3 The following items appear only when you set the HD Audio Controller to [Enabled]. Front Panel Type [HD] Allows you to set the front panel audio connector (AAFP) mode to legacy AC’97 or high-definition audio depending on the audio standard that the front panel audio module supports.
Intel LAN1 OPROM [Disabled] This item appears only when you set the previous item to [Enabled] and allows you to enable or disable the PXE OptionRom of the Intel LAN1 controller. Configuration options: [Enabled] [Disabled] Intel LAN2 Controller [Enabled] [Enabled] [Disabled] Enables the Intel® LAN2 controller. Disables the Intel® LAN2 controller.
3.6.8 APM ErP Ready [Disabled] Allows you to switch off some power at S4+S5 or S5 to get the system ready for ErP requirement. When set to [Enabled], all other PME options will be switched off. Configuration options: [Disabled] [Enabled (S4+S5)] [Enabled (S5)] Restore AC Power Loss [Power Off] [Power On] The system goes into ON state after an AC power loss. [Last State] The system goes into either OFF or ON state, whatever the system state was before the AC power loss.
3.6.9 Network Stack Network Stack [Disable] This item allows user to disable or enable the UEFI network stack. Configuration options: [Disable] [Enable] The following item appears only when you set the Network Stack to [Enabled]. Ipv4/Ipv6 PXE Support [Enabled] Allows you to enable or disable the Ipv4/Ipv6 PXE boot option.
3.7 Monitor menu The Monitor menu displays the system temperature/power status, and allows you to change the fan settings. Scroll down to display the other BIOS items. Chapter 3 CPU Temperature / MB Temperature [xxxºC/xxxºF] The onboard hardware monitor automatically detects and displays the CPU and motherboard temperatures. Select [Ignore] if you do not wish to display the detected temperatures.
CPU Q-Fan Control [Enabled] Allows you to set the CPU Q-Fan operating mode. [Enabled] Enables the CPU Q-Fan control feature. [Disabled] Disables the CPU Q-Fan control feature. The following items appear only when you set the CPU Q-Fan Control to [Enabled]. CPU Fan Speed Low Limit [300 RPM] Allows you to set the low limit warning for CPU Fan speed.
Chassis Fan Speed Low Limit 1/4 [300 RPM] This item appears only when you enable the Chassis Q-Fan Control feature and allows you to disable or set the chassis fan warning speed. Configuration options: [Ignore] [200 RPM] [300 RPM] [400 RPM] [500 RPM] [600 RPM] Chassis Fan 1/4 Profile [Silent] This item appears only when you enable the Chassis Q-Fan Control feature. It allows you to set the appropriate performance level of the chassis fan.
3.8 Boot menu The Boot menu items allow you to change the system boot options. Boot Configuration Fast Boot [Enabled] [Disabled] Allows your system to go back to its normal boot speed. [Enabled] Allows your system to accelerate the boot speed. Chapter 3 The following items appear only when you set the Fast Boot to [Enabled]. USB Support [Partial In...] 3-42 [Disabled] All USB devices will not be available until OS boot up for a fastest POST time.
PS/2 Keyboard and Mouse Support [Auto] Select any of these settings when PS/2 keyboard and mouse are installed. These settings only apply when Fast Boot is enabled. [Auto] For a faster POST time, PS/2 devices will only be available when the system boots up or rebooted when the PS/2 devices have not been reconnected or changed. If you disconnect or change PS/2 devices before restarting the system, PS/2 devices will not be available and BIOS setup program will not be accessible via PS/2 devices.
Post Delay Time [3 sec] This item appears only when you set the Full Screen Logo item to [Enabled]. This item allows you to select a desired additional POST waiting time to easily enter the BIOS Setup. You can only execute the POST delay time during normal boot. The values range from 0 to 10 seconds. This feature will only work when set under normal boot. Bootup NumLock State [On] Set the power-on state of the NumLock to [On]. [On] Set the power-on state of the NumLock to [Off].
Boot Devices Control [UEFI and Legacy OpROM] Allows you to select the type of devices that you want to boot. Configuration options: [UEFI and Legacy OpROM] [Legacy OpROM only] [UEFI only] Boot from Network Devices [Legacy OpROM first] Allows you to select the type of network devices that you want to launch. Configuration options: [Legacy OpROM first] [UEFI driver first] [Ignore] Boot from Storage Devices [Legacy OpROM first] Allows you to select the type of storage devices that you want to launch.
PK Management The Platform Key (PK) locks and secures the firmware from any permissible changes. The system verifies the PK before your system enters the OS. Delete PK Allows you to delete the PK from your system. Once the PK is deleted, all the system’s Secure Boot keys will not be active. Configuration options: [Yes] [No] Load PK from File Allows you to load the downloaded PK from a USB storage device.
Append db from File Allows you to load the additional db from a storage device so that more images can be loaded securely. Configuration options: [Yes] [No] The db file must be formatted as a UEFI variable structure with time-based authenticated variable. DBX Management The dbx (Revoked Signature database) lists the forbidden images of db items that are no longer trusted and cannot be loaded. Delete the dbx Allows you to delete the dbx file from your system.
3.9 Tools menu 3.9.1 ASUS EZ Flash 2 Utility The Tools menu items allow you to configure options for special functions. Select an item then press to display the submenu. Allows you to run ASUS EZ Flash 2. When you press , a confirmation message appears. Use the left/right arrow key to select between [Yes] or [No], then press to confirm your choice. For more details, refer to section 3.11.2 ASUS EZ Flash 2. 3.9.2 ASUS O.C.
Save to Profile Allows you to save the current BIOS settings to the BIOS Flash, and create a profile. Key in a profile number from one to eight, press , and then select Yes. Load from Profile Allows you to load the previous BIOS settings saved in the BIOS Flash. Key in the profile number that saved your BIOS settings, press , and then select Yes.
3.10 Exit menu The Exit menu items allow you to load the optimal default values for the BIOS items, and save or discard your changes to the BIOS items. You can access the EZ Mode from the Exit menu. Load Optimized Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press , a confirmation window appears. Select Yes to load the default values.
3.11 Updating BIOS The ASUS website publishes the latest BIOS versions to provide enhancements on system stability, compatibility, or performance. However, BIOS updating is potentially risky. If there is no problem using the current version of BIOS, DO NOT manually update the BIOS. Inappropriate BIOS updating may result in the system’s failure to boot. Carefully follow the instructions of this chapter to update your BIOS if necessary. Visit the ASUS website at www.asus.
3.11.2 ASUS EZ Flash 2 ASUS EZ Flash 2 allows you to update the BIOS without having to use a bootable floppy disk or an OS‑based utility. Before you start using this utility, download the latest BIOS from the ASUS website at www.asus.com. To update the BIOS using EZ Flash 2: Insert the USB flash disk that contains the latest BIOS file to the USB port. 2. Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select ASUS EZ Flash Utility and press to enable it. 3.
• ������������������������������������������������������������������������������������� This function can support devices such as a USB flash disk with FAT 32/16 format and single partition only. • ������������������������������������������������������������������������������� DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure! Ensure to load the BIOS default settings to ensure system compatibility and stability.
3.11.4 ASUS BIOS Updater The ASUS BIOS Updater allows you to update the BIOS in DOS environment. This utility also allows you to copy the current BIOS file that you can use as a backup when the BIOS fails or gets corrupted during the updating process. The succeeding utility screens are for reference only. The actual utility screen displays may not be same as shown. Before updating BIOS 1. Prepare the motherboard support DVD and a USB flash drive in FAT32/16 format and single partition. 2.
3. When the Make Disk menu appears, select the FreeDOS command prompt item by pressing the item number. 4. At the FreeDOS prompt, type d: and press to switch the disk from Drive C (optical drive) to Drive D (USB flash drive). Welcome to FreeDOS (http://www.freedos.org)! C:\>d: D:\> Updating the BIOS file To update the BIOS file using BIOS Updater: 1. At the FreeDOS prompt, type bupdater /pc /g and press . D:\>bupdater /pc /g 2. The BIOS Updater screen appears as below.
4. Select Yes and press . When BIOS update is done, press to exit BIOS Updater. Restart your computer. DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure! • ����������������������������������������������������������������������������������������� For BIOS Updater version 1.3 or later, the utility automatically exits to the DOS prompt after updating BIOS.
Chapter 4 Chapter 4: Software support 4.1 Installing an operating system • This motherboard supports Windows® 7 32/64-bit and Windows® 8 32/64-bit operating systems (OS). • ������������������������������������������������������������������������������� Motherboard settings and hardware options vary. The setup procedures presented in this chapter are for reference only. Refer to Windows® operating system documentation for detailed information. 4.
4.2.2 Obtaining the software manuals The software manuals are included in the support DVD. Follow the instructions below to get the necessary software manuals. The software manual files are in Portable Document Format (PDF). Install the Adobe® Acrobat® Reader from the Utilities tab before opening the files. To read about your motherboard’s utility guide: 1. Click Manual tab > ASUS Motherboard Utility Guide. 2. From the Manual folder, open the folder of the software manual that you wish to read. 3.
4.3 Software information 4.3.1 AI Suite 3 Most of the applications in the support DVD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software application for more information. AI Suite 3 is an all-in-one interface that integrates several ASUS utilities and allows you to launch and operate these utilities simultaneously. Installing AI Suite 3 To install AI Suite 3 on your computer: 1.
AI Suite 3 main menu bar DIGI+VRM Fan Xpert 2 EZ Update EPU USB 3.0 Boost Network iControl System Information USB BIOS Flashback USB Charger+ • ������������������������������������������������������������������������������������ The screeshots of AI Suite 3 in this user manual are for reference only. The actual screenshots vary with models.
4.3.2 DIGI+ VRM DIGI+ Power Control utility allows you to adjust the CPU and DRAM power settings for an optimum system efficiency, overall system stability and performance. Adjusting the CPU power Click or tap to undo the changes Click or tap to apply the changes CPU Load-line Calibration CPU Load-line Calibration adjusts the voltage range and controls the system temperature.
Adjusting the DRAM power Click or tap to undo the changes Click or tap to apply the changes DRAM Current Capability A higher value brings a wider total power range and extends the overclocking frequency range simultaneously. DRAM Voltage Frequency Allows you to adjust the DRAM switching frequency for system stability or to increase OC range.
4.3.3 EPU EPU is an enery-saving utility that allows you to adjust the CPU, GPU, and Fan Control settings to their power-saving conditions. To launch EPU, click EPU on the AI Suite 3 main menu bar.
4.3.4 Fan Xpert 2 Fan Xpert 2 automatically detects and tweaks the fan speeds, and provides you with optimized fan settings based on the fans’ specifications and positions. To launch Fan Xpert 2, click Fan Xpert 2 on the AI Suite 3 main menu bar.
RPM Mode RPM Mode allows you to set the fan speed when the CPU temperature is below 75oC. Click and drag to adjust the fan’s speed Click to go back to the previous screen Click to switch between the CPU and chassis fan screens • When the CPU temperature reaches 75o C, the fan will automatically run at full speed to protect the CPU. • For motherboard models without the CPU fan detection latch, only 4-pin CPU fans are controllable in Fan Xpert 2.
4.3.5 USB 3.0 Boost USB 3.0 Boost technology supports UASP (USB Attached SCSI Protocol) that automatically speeds up the transfer rates of your USB storage devices. To launch USB 3.0 Boost, click USB 3.0 Boost on the AI Suite 3 main menu bar. Using USB 3.0 Boost 1. Connect a USB 3.0 device to the USB 3.0 port. 2. From the USB 3.0 Boost screen, click to select a USB device. 3. To enable UASP on your USB device, click UASP. To revert to its normal transfer rate, click Normal.
4.3.6 EZ Update EZ Update is a utility that allows you to automatically update your motherboard’s softwares, drivers and the BIOS version easily. With this utlity, you can also manually update the saved BIOS and select a boot logo when the system goes into POST. To launch EZ Update, click EZ Update on the AI Suite 3 main menu bar.
4.3.7 Network iControl Network iControl is a one-stop setup network control center that allows you to manage your network bandwidth and set the bandwidth priority for your running programs. Launching Network iControl To launch Network iControl, click or tap the menu, then select Network iControl. on the top edge of the AI Suite 3 main • Ensure to install the LAN drivers before using this utility. • Network iControl can only support the onboard LAN.
EZ Profile screen Click or tap to save the profile settings or rename the profile Click or tap to select a network profile Click or tap to set the program as High, Normal, or Low priority Tick to assign a schedule of your network programs to avoid network congestions Chapter 4 Select a program from this list and click to add to your network profile ASUS P9D WS 4-13
4.3.8 System Information This utility allows you get the detailed information of the motherboard, CPU, and memory settings. To launch System Information, click System Information on the AI Suite 3 main menu bar. Viewing the motherboard information From the System Information screen, click MB tab to view the motherboard’s information. Viewing the CPU information From the System Information screen, click CPU tab to view the processor’s information.
Viewing the SPD information Chapter 4 From the System Information screen, click SPD tab to view the memory’s information.
4.3.9 USB BIOS Flashback USB BIOS Flashback allows you to check and save the latest BIOS version to a USB storage device. Use this utility to quickly check for the latest available BIOS and set a schedule to when you can download for a newer version. To launch USB BIOS Flashback, click USB BIOS Flashback on the AI Suite 3 main menu bar.
4.3.10 USB Charger+ USB Charger+ allows you to quick-charge your portable USB devices even if your computer is off, in sleep mode or hibernate mode. The USB Charger+ will not work if the ErP-ready item in the BIOS is enabled. Launching USB Charger+ To launch USB Charger+, click on the AI Suite 3 main menu bar.
4.3.11 Audio configurations The Realtek audio CODEC provides 8-channel audio capability to deliver the ultimate audio experience on your computer. The software provides Jack-Sensing function, S/PDIF Out support, and interrupt capability. The CODEC also includes the Realtek® proprietary UAJ® (Universal Audio Jack) technology for all audio ports, eliminating cable connection errors, and giving users plug and play convenience.
B. Realtek® HD Audio Manager with DTS UltraPC II for Windows® 8 / Windows® 7 / Windows® Vista To display Quick Volume Adjustment Bar, click To launch Realtek® HD Audio Manager, click from the taskbar then click . from the taskbar then double-click .
Chapter 4 4-20 Chapter 4: Software support
Chapter 5 Chapter 5: 5.1 ATI® CrossFireX™ technology Multiple GPU technology support The motherboard supports the ATI® CrossFireX™ technology that allows you to install multigraphics processing units (GPU) graphics cards. Follow the installation procedures in this section. 5.1.1 • • Requirements In CrossFireX mode, you should have two identical CrossFireX-ready graphics cards or one CrossFireX-ready dual-GPU graphics card that are ATI® certified.
5.1.3 Installing two CrossFireX™ graphics cards Chapter 5 The following pictures are for reference only. The graphics cards and the motherboard layout may vary with models, but the installation steps remain the same. 1. Prepare two CrossFireX-ready graphics cards. 2. Insert the two graphics card into the PCIEX16 slots. If your motherboard has more than two PCIEX16 slots, refer to Chapter 1 in this user manual for the locations of the PCIEX16 slots recommended for multi-graphics card installation. 3.
Connect two independent auxiliary power sources from the power supply to the two graphics cards separately. 6. Connect a VGA or a DVI cable to the graphics card. 5.1.4 Chapter 5 5. Installing three CrossFireX™ graphics cards 1. Prepare three CrossFireX-ready graphics cards. 2. Insert the three graphics card into the PCIEX16 slots.
5.1.5 Chapter 5 5-4 Installing four CrossFireX™ graphics cards 1. Prepare four CrossFireX-ready graphics cards. 2. Insert the four graphics card into the PCIEX16 slots. Refer to Chapter 1 in this user manual for the locations of the PCIEX16 slots recommended for multi-graphics card installation. 3. Ensure that the cards are properly seated on the slots. 4. Align and firmly insert the four CrossFireX bridge connectors to the goldfingers on each graphics card.
5.1.6 Installing the device drivers Chapter 5 Refer to the documentation that came with your graphics card package to install the device drivers. Ensure that your PCI Express graphics card driver supports the AMD® CrossFireX™ technology. Download the latest driver from the AMD website (www.amd.com). 5.1.7 Enabling the AMD® CrossFireX™ technology After installing your graphics cards and the device drivers, enable the CrossFireX™ feature through the AMD Catalyst™ Control Center in Windows environment.
Enabling Dual CrossFireX technology Chapter 5 1. In the Catalyst Control Center window, click Performance > AMD CrossFireXTM. 2. Select Enable CrossFireXTM. 3. Select a GPU combination from the drop-down list. 4. Click Apply to save and activate the GPU settings made.
ASUS contact information ASUSTeK COMPUTER INC. Address Telephone Fax E-mail Web site Technical Support Telephone Online support 15 Li-Te Road, Peitou, Taipei, Taiwan 11259 +886-2-2894-3447 +886-2-2890-7798 info@asus.com.tw tw.asus.com +86-21-38429911 support.asus.com ASUS COMPUTER INTERNATIONAL (America) Address Telephone Fax Web site Technical Support Telephone Support fax Online support 800 Corporate Way, Fremont, CA 94539, USA +1-812-282-3777 +1-510-608-4555 usa.
(510)739-3777/(510)608-4555 800 Corporate Way, Fremont, CA 94539. Asus Computer International Signature : Date : Representative Person’s Name : Apr. 29, 2013 Steve Chang / President This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
